Inaxsys COAX2IP User manual

COAX2IP

10/100Base-Tx Long Reach

Ethernet Extender

BNC

User Manual

Introduction

Long Reach Ethernet Extender with one

Ethernet port (on 1 RJ-45 connector) and one

VDSL port on 1 BNC connector. This is a bridge mode modem accommodating Ethernet and

VDSL technologies to extend Ethernet over single-pair phone line by using a VDSL signal.

Up to 100/60 Mbps (or 90/90 Mbps with synchronous data rate) transition bandwidth within 300m and 40/10 Mbps for 1km long range connections provides ultra-high performance to the pervasive telephone line network. Its plug-n-play solution minimum installation time & cost by allowing video streaming and data to share the same telephone pair without interference.

With one DIP switches configuration, the product includes the CO (Central Office) site and CPE (Customer Premise Equipment) site.

The long distance support feature makes this extender be a great and ideal solution for FTTx

(Fiber to the Building, Fiber to the Campus or

Fiber to the Home) applications. It supports high bandwidth VDSL2 over existing telephone wires in the “last mile” from the ISP / Telecom /

Service provider’s fiber mode to the buildings and customers’ home.

LED Indicators

LED Status Description

Duplex

Speed

Link/Act

Power

CO

Nego

/Link

/Act

On

Off

On off

RJ 45 port full duplex

RJ 45 port half duplex

RJ 45 connect at 100M

RJ 45 connect at 10M

On

Blinking

On

RJ 45 port is link

RJ 45 port Data is transmitting or receiving

Power is on.

Off Power is off.

On flash

Blinking

Work as Master at Core center off

Work as CPE at Edge site

Blinking Negotiation

On Link is connected

Data Active

Key Features

Front Panel (LEDs)

 1 full-duplex VDSL links via BNC connector

 Selectable CO and CPE mode

 Selectable fast and interleaved mode

 Selectable target SNR margin

 Compliant with ETSI, ITU and

ANSI standards

DIP Switches Mode Configuration

DIP 1 2 3 4

On CO Fast 998ISDN 6dB

Off CPE Interleave Symmetric 9dB

 Pin 1 CPE or CO mode selection

 Pin 2 Interleave mode or fast mode selection

 Pin 3 Symmetric ISDN Mode or

998 ISDN Mode selection

 Pin4 Signal Noise Rate selection for 9dB or 6dB

Package Contents

Before you start to install this switch, please verify your package that contains the following items:

 One Long Reach Ethernet Extender

 One Power Adaptor

 One User Manual

Note: If any of these items is found missing or damaged, please contact your local supplier for replacement.

Mechanical Technical Specifications

Standards

IEEE802.3 10Base-T

IEEE802.3u 100Base-TX

IEEE802.3x Full Duplex

ETSI

ITU

ANSI

Full ITU-T G.993.1 (VDSL) compatible

G.997.1 compatible.

BNC for coaxial cable) Interface

Power Input

Dimensions

RJ-45 female Ethernet jack

Switching Method Store and Forward

Duplex

LED

Indicators

Speed

Link / Act

Power

Master

Link / Negotiation

DC 5V/2A

102 × 75 × 23 mm

(L x W x H)

Weight

Operating

Temperature

0 to 45℃

Storage

Temperature

-20 to 90℃

Humidity

Certifications

10 to 90% RH

(non-condensing)

FCC Class A, CE

FCC Warning

This device has been tested and found to comply with limits for a Class A digital device and pursuant to Part 15 of FCC Rules.

These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates and radiates radio frequency energy. If it’s not installed and used in accordance with the user’s manual, it may cause interference. In which case, users will be required to correct interference at their own expenses.

CE Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

8272 Pascal Gagnon, Saint-Leonard, Quebec, Canada, H1P 1Y4, www.inaxsys.com