mount-it! MI-2781 Dual Monitor Desk Stand for 13 in. to 32 in. Monitors Use and Care Manual
Add to my manuals
6 Pages
advertisement
Installation Instruction
English
UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other !
protective surface to avoid damage.
!
Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts.
!
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before !
installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.
!
Please call a qualified installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
1
Supplied Par ts List
(1) Pole-a
(2) VESA Plate-d
(1) Weighted Base-b (1) Swivel Arm-c
(3) M5x14 Bolt-e
(2) Nut-h
(1)M10 Bolt-i (1)Support Plate-j (1)M10 Washer-k (1)Spring Washer-l
(1) Grommet Base
Plate-m
(1)Wire Clip-n1 (4)Wire Clip-n2 (1)Allen Key-o
(1)Wrench-p
!
WARNING
(8)M4x12 Bolt-q (8)M4x30 Bolt-r (8)M4 Spacer-s
Tools Required
CAUTION!
The monitor desktop mount must be evenly positioned on a stable horizontal surface. If the mount is not positioned in a balanced manner, it may fall, resulting in possible injury and/or damage. The optional desktop bolt may be used to provide additional stability.
2
Phillips Screwdriver
Step 1 Install the Pole to the Desktop
Option A: Weighted Base Install
1. Install the Pole(a) to the Weighted
Base(b) using 3pcs M5x14 Bolts(e), and tighten using the Allen Key(o), see Figure 1.
2. Optionally, you can drill a 10mm diameter hole in your desk and secure using the
Support Plate (j), M10 Washer(k), Spring
Washer(l) and M10 Bolt(i). Fasten the M10
Bolt with provided Wrench(p), see Figure 2.
a l l i k j
Figure 2
Figure 1 e b
Option B: Grommet Base Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(e), and tighten using the Allen Key(o), see Figure 3.
2. Position the Pole(a) on the mounting surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 4.
e
Figure 3
Figure 4 l i k j a m
3
Step 1 Install the Pole to the Desktop
Option B: Grommet Base Install
Self Drilled Grommet Hole Installation
1. Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked position through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(e), and tighten using the Allen Key(o), see Figure 5.
3. Position the Pole(a) on the mounting surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 6.
e
Figure 5
Figure 6 l i k j a m
Step 2 Install Arm to the Pole
Install Swivel Arm(c) to the
Pole(a). Fasten the bolt with supplied Allen Key(o). Attach the Wire Clip(n1,n2) to the
Pole(a) and Swivel Arm(c).
c o n1 n2
4
Step 3 Attach the VESA Plate to the Monitor q s r
For Monitor with Flat Back For Monitor with Curved or
Recessed Back
Step 4 Slide the Monitor onto the Head of Swivel Arm h
Slide the monitor onto the head of
Swivel Arm(c) as shown in the above diagram.
Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.
5
Step 5 Fix the Tilt Angle and Adjust the Level of Monitor o o
Fix the tilt angle
Tighten the bolt with the supplied Allen
Key(o) to fix the tilt angle.
Ignore this step if monitors are level
If one monitor is lower, remove the Nut(h) and turn the bolt counter-clockwise with supplied
Allen key(o) to raise the monitor. Install the
Nut(h) after the adjustment.
Step 6 Make the Necessary Adjustments and Manage the Wires o n1
Use the supplied Allen Key(o) to make the necessary adjustments.
Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use.
Thank you for choosing our products!
6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement