HD CCTV

Digital Video Dome Camera

OPERATION MANUAL

M149-HDD122-001

Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.

C A U T I O N

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

2

C O N T E N T S

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

• Menu structure

• Function Description

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that

may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Caution

Any changes or modifications in construction of this devices which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera

for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality

75Ω video impedance level.

If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reflective light, which may

cause smear on the picture and possible damage to the Image Sensor.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing

connection.

4

1. CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

Household users should contact either the retailer where they for disposal.

5

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

6

3. FEATURES

• High Resolution

SONY 1 / 3” 2.1 M Progressive Color CMOS Image Sensor, 1920x1080 30fps

• Support various digital video output

720p60, 720p50, 1080p30, 1080p25

• Video Outputs

Primary HD-SDI (BNC)

Test/Setup TV Out (Test Point-adapter to BNC included), NTSC/PAL selectable

• OSD menu for setup and configuration

• Provides True Day / Night Capability with Motorized IR Cut Filter.

( TDN Type Model Only )

• 30 Long Life IR illuminations for 0 Lux viewing performance and

range to 20m ( 65feet ) ( LED type model only )

• Lens Control

DC Iris / Board Lens

• Power Source

DC 12V / AC24V ( Dual Power Type )

DC 12V ( DC Power Type )

• 3-Acix Gimbal

Pan Rotation

Tilting angle

70˚

Tilt Rotation

70˚

Horizontal Rotation

Standard Type

7

LED Type

4. EQUIPMENT AND ACCESSORIES

Camera

Template

Screws

Manual

Service Video Output Test Cable

8

5. CAMERA COMPONENT DESCRIPTIONS

• LED Type

I R L E D 3 0 e a

P h o t o C e l l

• Standard Type

S e r v i c e V i d e o C o n n e c t o r

F u n c t i o n S e t u p S w i t c h

• CONTROL FUNCTION

(OSD JOYSTICK)

U P

R I G H T

L E F T

M E N U

D O W N

*PRESS INWARD FOR MENU

9

S e r v i c e V i d e o C o n n e c t o r

F u n c t i o n S e t u p S w i t c h

6. INSTALLATION

3

1

2

Lens Focus Knob

Lens Zoom Knob

4

5

6

10

Separate LED Cover (Sunshield Cover) and adjust LENS ZOOM / FOCUS KNOB

After setting the LENS, assemble the

LED Cover (Sunshield Cover).

7

8

9

6

7

4

5

NO

1

2

3

8

9

PART NAME

Mount Guide

Housing Bottom

Holder Panning

Holder Tlit

Holder Rotate

Cover IR Led (LED Type)

Cover Sun Shield (Standard Type)

Housing Top

Dome Cover

6. INSTALLATION

• MONITOR CONNECTION

- DC12V/AC24V

B N C F E M A L E V I D E O

HD SDI IN

SDI

RECEIVER

DISPLAY

DEVICE

MONITOR

DC 12V / AC 24V POWER SUPPLY

- DC12V

- Service Video connector

BNC FEMALE V I D E O

HD SDI IN

SDI

RECEIVER

DISPLAY

DEVICE

MONITOR

DC 12V POWER SUPPLY

HANDHELD

MONITOR

OPEN

COVER

VIDEO IN

Service Video Connector TEST CABLE

When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.

11

7. DIMENSIONS

Unit(mm)

Ø100

Ø135

Ø108.5

12

8. SPECIFICATION

Model

Image Device

Effective Pixels

Unit cell size

Video Output Mode

Minimum Illumination

S/N Ratio

Shutter Speed

Manual Shutter Speed

Standard Type LED Type

SONY 1/3” 2.1M Progressive

Color CMOS Image Sensor

1984 (H) x 1105 (V) 30fps

2.8um (H) x 2.8um (V)

HD-SDI: 720p60, 720p50,1080p30, 1080p25

TV Out: NTSC / PAL selectable

0.1 Lux 0 Lux

More than 50dB

Auto / Manual selectable

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K

IR CUT Pass Filter change

29 dB

AUTO / AUTOext / PUSH / MANUAL

DC IRIS / Board Lens

Yes

True Day/Night

Controllable Max Gain

White Balance

Lens Control

OSD Menu

Power

Consumption

IR LED

IR Beam Range

Dimension

Weight

DC

Dual

DC12V(±10%), Max. 180mA

DC12V(±10%), Max. 220mA

AC24V(±10%), Max. 3.1W

-

-

136.4(

Φ

343g

DC12V(±10%), Max. 370mA

DC12V(±10%), Max. 470mA

AC24V(±10%), Max. 5.6W

Up to 20M (65 Feet)

) x 95.3(mm)

850nm, 30ea

Conformity

Temperature / Humidity

(no condensing)

CE, FCC, KC

Operation: 14°F~122°F(-10°C~+50°C / 20~80%)

Storage: - 4 ° F ~ 1 5 8 ° F ( - 2 0 ° C ~ + 7 0 ° C / 2 0 ~ 9 5 % )

S p e c i f i c a t i o n s a n d d e s i g n s a r e s u b j e c t t o c h a n g e f o r i m p r o v i n g t h e f u n c t i o n a l i t y o f t h i s p r o d u c t w i t h o u t n o t i c e .

13

9. OSD MANUAL

• Menu structure

SETUP

EXPOSURE

WHITE BALANCE

WDR / BLC

DNR

DAY & NIGHT

IMAGE

SPECIAL

SYSTEN

RESET DATA ALL

EXT

Main

EXPOSURE

WHITE

BALANCE

WDR / BLC

DNR

Sub Menu Sub Menu

BRIGHTNESS 0 ~ 20

AE MODE

(DC IRIS Only)

LENS (IRIS)

(DC IRIS Only)

NORMAL AE / INDOOR

MANUAL / AUTO

SHUTTER

MANUAL /

LEVEL

AUTO

RETURN

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.

BACK / EXIT

OFF, X2, X3, X4. X5, X6, X7, X8 DSS

AGC

BASE FREQ

0 ~ 10

60Hz / 50Hz

RESET DATA BACK / DEF.

RETURN

WB MODE

BACK / EXIT.

COLORTEMP. LOW / MIDDLE / HIGH

AUTO

/AUTOext

/PUSH

/MANUAL

R-GAIN

B-GAIN

RETURN

0 ~ 20

0 ~ 20

BACK / EXIT

SATURATION 0 ~ 20

RESET DATA BACK / DEF.

RETURN

MODE

BACK / EXIT.

OFF/ WDR/ BLC/ D-WDR

WDR WGT

BLC OSD

BLC POS-X

BLC POS-Y

0 ~ 4

OFF, ON

0 ~ 20

0 ~ 20

BLC SIZE-X

BLC SIZE-Y

0 ~ 20

0 ~ 20

RESET DATA BACK / DEF.

RETURN BACK / EXIT.

OFF / LOW / MIDDLE / HIGH

14

9

. OSD MANUAL

Main

DAY &

NIGHT

IMAGE

SPECIAL

SYSTEM

Sub Menu Sub Menu

D&N DETECT

COLOR /

B&W /

AUTO

DELAY

D->N LEVEL

N->D LEVEL

RESET DATA

RETURN

AGC / SENSE (LED Type Only)

1sec, 3, 5, 10, 15, 20, 25, 30, 40, 50, 60sec

0 ~ 20(AGC) / 0 ~10(SENSE)

0 ~ 20(AGC) / 0 ~10(SENSE)

BACK / DEF.

BACK / EXIT.

SHARPNESS

GAMMA

0 ~ 20

0 ~ 4

FLIP OFF, H FLIP, V FLIP, HV FLIP

LENS SHADING OFF, ON

DZOOM

RESET DATA

RETURN

1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x

BACK / DEF.

BACK / EXIT.

ZONE NO.

0 ~ 23

PRIVACY

HLMASK

PATTERN

RESET DATA

RETURN

SDI FORMAT

SDI FPS

OFF/ ON

ZONE OP.

X-POS

Y-POS

X-SIZ

Y-SIZ

COLOR

TRANS.

RESET DATA

OFF/ ON

OFF / 0 / 1

BACK / DEF.

BACK / EXIT.

1080P / 720P

RETURN

LEVEL

COLOR

RESET DATA

RETURN

OFF/ ON

0 ~ 60

0 ~ 40

0 ~ 40

0 ~ 40

BLK, WHI, YEL, CYN, GRN, MAG, RED, BLU

0 ~ 4

BACK / DEF.

BACK / EXIT.

0 ~ 20

BLK, WHI, YEL, CYN, GRN, MAG, RED, BLU

BACK / DEF.

BACK / EXIT.

CVBS FORMAT

SYSTEM INFO.

30(60) / 25(50)

CVBS OUT

NTSC /

PAL

CVBS VIEW

RETURN

S/W VERSION

SET VERSION

RETURN

AUTO / OFF / ON(WDR OFF)

CROP / FULL

BACK / EXIT.

BACK / EXIT.

REBOOT

RETURN BACK / EXIT.

15

9

. OSD MANUAL

• Function Description

0. SETUP

- EXPOSURE : Go sub menu for camera exposure control.

- WHITE BALANCE : Go sub menu for camera white balance control.

- WDR/BLC : Go sub menu for camera WDR or BLC action.

- DNR

- DAY & NIGHT

- IMAGE

: Control noise reduction setting.

: Go sub menu for camera day & night control.

: Go sub menu for adjust image functions.

- SPECIAL

- SYSTEM

- RESET DATA ALL

: Go sub menu for special feature control.

: Go sub menu for system control & information.

: Reset camera’s all feature data to default value.

1. EXPOSURE

- BRIGHTNESS

- AE MODE

- LENS(IRIS)

- SHUTTER

• LEVEL

- DSS

- AGC

- BASE FREQ

: Adjust image brightness value.

: Adjust AE control mode. ( DC Iris Model Only )

: Select lens iris control type. ( DC Iris Model Only )

: Select shutter speed control type.

: Adjust shutter speed at manual shutter mode.

: Adjust digital slow shutter control level.

: Adjust max gain level for brightness control.

: Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE

• AUTO

: Select white balance control mode.

: Full auto control mode in color temperature rage

2300K~10000K.

• AUTOext

• PUSH

: Extended auto mode for special illumination.

: Enable fix the control setting for specific environment.

Push & release, for fix WB control setting.

• MANUAL

: Enable WB control setting by user’s intention.

◦

COLOR TEMP. : Select color temperature range for WB control at manual mode

◦

R-GAIN

◦

B-GAIN

: Adjust red color gain for WB control at maual mode.

: Adjust blue color gain for WB control at manual mode.

- SATURATION : Adjust color saturation level.

16

9

. OSD MANUAL

3. WDR/BLC

- MODE

• WDR

• BLC

• D-WDR

- WDR WGT

- BLC OSD

- BLC POS-X

- BLC POS-Y

- BLC SIZ-X

- BLC SIZ-Y

: Select WDR / BLC mode.

: Act in wdie dynamic rage mode. Controled video frame rate in 1/2.

: Act in Backlight compensation mode.

: Digital wide dynamic range control.

: WDR weight control level settig at WDR mode.

: Display BLC control zone in screen.

: Select BLC control zone vertical position.

: Select BLC control zone horizontal position.

: Select BLC control zone vertical size.

: Select BLC control zone horizontal size.

4. DNR

: Reduce image’s noise

5. DAY & NIGHT

- MODE

• AUTO

: Select TDN(True Day & Night control) mode.

: Camera controlled automatically to decide day or night

environment using AGC calculation data.

• COLOR

: Fix to mode at day environment setting.

• B&W

Make video image act in color.

: Fix to mode at night environment setting.

Make video image act in B/W and IR filter change.

■

D/N DETECT : Select AGC or CDS control for TDN auto control.

■

DELAY

■

D->N LEVEL

■

N->D LEVEL

: Delay time for change day or night mode at auto mode.

: Threshold level for change Day to Night mode.

: Threshold level for change Night to Day mode.

6. IMAGE

- SHARPNESS

- GAMMA

- FLIP

: Adjust image sharpness level.

: Gamma Curve Select.

: Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

7. SPECIAL

- PRIVACY

• ZONE NO.

• ZONE OP.

• X-POS

• Y-POS

• X-SIZ

• Y-SIZ

• COLOR

• TRANS.

: Setting for protect private area in image using mask setting.

: Select private mask zone number.

: Select zone mask display on/off.

: Select zone horizontal position.

: Select zone vertical position.

: Select zone horizontal size.

: Select zone vertical size.

: Select mask color.

: Select mask transparency level.

17

9

. OSD MANUAL

- HLMASK

• LEVEL

• COLOR

- PATTERN

8. SYSTEM

- SDI FORMAT

- SDI FPS

- CVBS FORMAT

• CVBS OUT

◦

ON, OFF

◦

AUTO

• CVBS VIEW

◦

CROP

◦

FULL

: Mask image high light area.

: Select high light level.

: Select mask color.

: Color bar display Select.

: 1080P / 720P.

: 30 or 25 fps in 1080p mode. 60 or 50 fps in 720p mode.

: NTSC / PAL.

: Select mode for CVBS out action.

: Enable or Disable CVBS out data.

: Check automatically CVBS video cable connection.

If connected, CVBS out data is enable and WDR mode

is setted off automatically.

: CVBS out video angle setting.

: Cut the scene outside area for keep image aspect ratio.

: Fill the full angle scene into image with

H-V size & ratio change.

- SYSTEM INFO.

• S/W VERSION

• SET VERSION

: Camera’s basic software version.

: Camera’s feature control setting version.

18