AM/FM STEREO CD CASSETTE RECORDER

USER MANUAL

KT2028A

CAUTION: Electrically Operated Product – Please use care

when plugging into AC outlet.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD,DO NOT USE THIS PLUG WITH AN EXTENSION CORD,RECEPTACLE OR

OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT

FIRE OR SHOCK HAZARD.DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol , within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING : TO REDUCE THE RISK OF

ELECTRIC SHOCK , DO NOT

REMOVE COVER (OR BACK), NO

USER SERVICEABLE PARTS INSIDE,

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The Caution Marking is located at the bottom of the unit.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Cleaning – Unplug this product from the wall outlet before cleaning, do not use liquid cleaners or aerosol cleaners.

Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product.

Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

A Product and Cart Combination Should Be Moved with Care – Quick stops, excessive force and uneven surfaces may cause the product and cart combination to overturn.

9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

12. Only use attachments/accessories specified by the manufacturer.

13. Unplug this apparatus during lightening storms or when unused for long period of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on the apparatus.

16. Do not overload wall outlet. Use only power source as indicated.

17. Use replacement part as specified by the manufacturer.

18. The product may be mounted to a wall only if recommended by the manufacturer.

19. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks.

20. Excessive sound pressure from earphones and headphones can cause hearing loss.

21. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

1

CAUTION

CLASS 1 LASER PRODUCT

CLASS 1 LASER PRODUCT

APPAREIL LASER DE CLASSE 1

PRODUCTO LASER DE CLASE 1

This product contains a low power laser device.

CAUTION

INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCKS

DEFEATED.

AVOID EXPOSURE TO BEAM

Follow the advice below for safe operations.

·

·

·

·

·

ON PROTECTION AGAINST LASER ENERGY EXPOSURE

· As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the casing.

Stop operation immediately if any liquid or solid object should fall into the cabinet.

Do not touch the lens or poke at it. If you do, you may damage the lens and the player may not operate properly.

Do not put anything in the safety slot. If you do, the laser diode will be “ON” when the CD door is still open.

If the unit is not to be used for a long period of time, make sure that all power sources are disconnected from the unit. Remove all batteries from the battery compartment, and unplug the AC cord from the wall outlet.

Make it a practice to remove the AC cord by grasping the main body and not by pulling the cord.

This unit employs a laser. The use of controls or adjustment or performance of procedures other than those specified here may result in exposure to hazardous radiation.

·

·

ON PLACEMENT

· Do not use the unit in places which are extremely hot, cold, dusty or humid.

Place the unit on a flat and even surface.

·

·

·

Do not restrict the air-flow of the unit by placing it in a place with poor ventilation, by covering it with a cloth or by placing it on a carpet.

ON CONDENSATION

When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit.

When there is condensation inside the unit, the unit may not function normally.

Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.

Should any trouble occur, remove the power source and refer servicing to qualified personnel.

2

FUNCTIONS AND CONTROLS

1. TELESCOPIC ANTENNA

2. CD COMPARTMENT LID

3. CD OPEN BUTTON

4. DIAL LENS

5. CD PLAY/PAUSE BUTTON

6. CASSETTE COMPARTMENT

7. CD SKIP BACKWARD BUTTON

8. REPEAT INDICATOR (REPEAT)

9. PLAY INDICATOR (PLAY )

10. CD SKIP FORWARD BUTTON

11. CD REPEAT BUTTON

12. CD STOP BUTTON

13. PROGRAM INDICATOR (PROGRAM)

14. LCD DISPLAY

15. REPEAT ALL INDICATOR (ALL)

16. CD PROGRAM BUTTON

17. AC INPUT SOCKET (AC IN~)

18. AUX IN JACK

19. FUNCTION/POWER SWITCH

20. VOLUME CONTROL

21. BAND SELECTOR

22. TUNING CONTROL

23. BATTERY COMPARTMENT

24. PAUSE BUTTON

25. STOP/EJECT BUTTON

26. FAST FORWARD BUTTON

27. REWIND BUTTON

28. PLAY BUTTON

29. RECORD BUTTON

3

POWER SOURCE

This AM/FM STEREO CD Cassette Recorder operates on 8 x ‘LR14’ (‘C’) batteries (not included) or from AC 120V~ 60Hz line power supply.

A. BATTERY OPERATION

1. Remove the Battery Door.

2. Following the polarity diagram as shown in the battery compartment insert 8 x ‘LR14’ (‘C') batteries then replace the Battery Door.

IMPORTANT : Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.

3. Use only the size and type of batteries specified.

4. For better performance and longer operating time, we recommend the use of alkaline-type batteries.

5. Do not mix old and new batteries.

6. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

7. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and may void the warranty.

8. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

(Follow battery manufacturer’s directions).

9. Do not dispose of batteries in fire, batteries may leak or explode.

B. AC OPERATION

When the AC power cord (included) is connected to the AC INPUT Socket (# 17) at the back of the unit and the other end to a wall outlet with AC 120V ~ 60Hz power supply, the unit will disconnect the batteries automatically, and operate from AC power instead.

Note: plug is used as the disconnect device. The disconnect device shall remain readily operable.

In order to disconnect the apparatus from the mains completely, the mains plug should be

disconnected from the mains socket outlet completely

IMPORTANT :

This unit has a polarized AC plug with one wide blade and one narrow blade. This plug will only fit into a matching polarized AC outlet. This is a safety feature to reduce the possibility of electric shock. If this plug will not fit in your AC outlet, you probably have an outdated non-polarized outlet. You should have your out-dated outlet changed by a qualified, licensed electrician. Do not file the wide blade on the plug, or use an adaptor to make the plug fit onto your outlet. This defeats the safety feature and could expose you to electric shock.

AC Plug

AC Outlet

4

CD PLAYER OPERATION

Note: This player not only plays commercial CDs but also plays self-compiled CD-R/RW discs.

1. Set the Function/ Power Switch (# 19) to "CD" position. The player will display “- -”.

2. Open the CD LID by pressing the CD OPEN Button (# 3). Carefully place an audio CD,

with its label side upward, in the CD compartment and close the CD Door.

3. The total number of tracks on the CD will appear in the LCD Display (# 14) after

a few seconds.

4. Press the CD PLAY/PAUSE Button (# 5). The CD PLAY Indicator “ PLAY ”

will light and the CD will start playing from the first track.

5. Adjust the Volume Control (# 20) to obtain the desired sound level from

the Built-in Speakers.

6. To suspend playing, press the CD PLAY/PAUSE Button (# 5).

The CD PLAY Indicator “ PLAY ” will flash.

To resume playing, press the CD PLAY/PAUSE Button (# 5) again.

7. You can choose to play your favorite track directly by pressing either the CD Skip Forward

Button (#10) or CD Skip Backward Button (#7).

The LCD Display (#14) will indicate the correct track number selected.

8. To locate a particular passage within a track, keep the CD Search Forward Button (#10) or

CD Search Back ward Button (#7) depressed until it is found.

9. To repeat a particular track, press the CD REPEAT Button (# 11) once or until the CD REPEAT

Indicator “ REPEAT” (# 8) lights.

10. To repeat the entire CD, press the CD REPEAT Button (# 11) twice or until the CD REPEAT

Indicator “ REPEAT ALL” (# 8,15) lights.

11. To stop playing, press the CD STOP Button (# 12).

12. When you wish to turn off the CD PLAYER, set the Function/Power Switch (# 19) to "TAPE".

CD PROGRAMMED PLAY

This function allows the tracks to be played in a programmed sequence.

1. In CD stop mode, press the PROGRAM Button (#16) once. The CD PROGRAM

Indicator “ PROGRAM” (# 13) will flash and “00” will appear and blink in the

LCD Display (# 14) to prompt for input.

2. Press the CD Skip BACKWARD Button (#7) or CD Skip FORWARD Button

(#10) to select the song to be programmed. For example track 8 is selected.

3. Press the PROGRAM Button (# 16) again to store the selection. The Program

Channel No. will change to “ 00” and blink to prompt for Input.

4. Press the CD Skip Forward Button (#10) or CD Skip Backward Button (#7)

to select the next song to be programmed and press the PROGRAM Button (#16) to

store the selection. For example second selection is track 15.

5. You may repeat steps 2 - 4 to program as many as 20 tracks.

The LCD Display (#14) will display “- -” after programming 20 tracks.

6. Press the CD PLAY/PAUSE Button (# 5) to start playing in the programmed

sequence. The PLAY lndicator "PLAY " appears with the PROGRAM lndicator,

" PROGRAM", flashing in the Display.

7. Adjust the Volume Control (# 20) to obtain the desired sound level from the Built-in

Speakers.

8. To resume to normal playback, in CD Stop mode press the PLAY/PAUSE Button (#5) again.

9. When you wish to turn off the CD PLAYER, set the Function /Power Switch (# 19) to the

"TAPE" position.

5

Note on CD-R/RW discs

- Because of non-standardized format definition/ production of CD-R/RW,

playback quality and performance are not guaranteed.

- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions,

such as PC performance, writing software, media ability, etc.

- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.

- It is recommended to record only audio files on CD-R/RW discs for easy reading.

RADIO RECEPTION

1. Set the Function /Power Switch (# 19) to the "RADIO" position.

2. Set the Band Selector (# 21) to "AM" or “FM ST” for the desired radio band.

3. Turn the Tuning Control (# 22) to tune to your desired radio station.

4. Adjust the Volume Control (# 20) to obtain the desired sound level.

5. To turn the Radio off, set the Function /Power Switch (# 19) to the “TAPE” position.

TIPS FOR BEST RADIO RECEPTION

1. To insure maximum FM tuner sensitivity, the Telescopic Antenna (#1) should be fully extended

and rotated to obtain the best possible reception.

2. When tuning in AM reception, to insure best AM sensitivity, try repositioning the unit until the best

reception is obtained.

CASSETTE RECORDER OPERATION

1. Set the Function /Power Switch (# 19) to the "TAPE" position.

2. Open the Cassette Door (# 6) by pressing the STOP/EJECT Button (# 25) and insert a

pre-recorded cassette tape with the exposed tape facing upwards. Close the Cassette Door.

3. Press the Cassette Play Button (# 28) and adjust the Volume Control (# 20) to obtain the

desired sound level.

4. Press the Cassette Pause Button (# 24) to suspend play. Press the same button again to resume.

5. Press the Cassette F. FWD Button (# 26) or the Cassette REW Button (# 27) to rapidly

advance or rewind the tape.

6. Press the Cassette Record Button (# 29) to record either from the Radio or CD.

Use the Function /Power Switch (# 19) to choose your signal source accordingly.

7. Press the STOP/EJECT Button (# 25) to stop operation.

AUTOMATIC STOP

To protect your cassette tapes and prevent unnecessary wear to the pinch rollrt of the cassette mechanism,this unit is equipped with an Automatic Stop System. When the tape ends during play,the

Cassette Play Button (#28) will automatically release to stop the cassette from running.

6

CASSETTE TAPE OPERATING TIPS

1. High quality tapes are recommended to obtain maximum quality reproduction from recordings.

2. Tapes with playing time of 120 minutes (C-120) are not recommended because they contain

thinner and longer tape that has a greater chance to malfunction and jam, which may damage

the cassette mechanism.

3. To obtain good reproduction, the head should be cleaned after every 10 to 20 hours of use.

It is also recommended that the cassette be kept away from excessive heat or cold.

4. If there is slack in the tape, remove the slack prior to inserting the cassette. To remove the slack,

insert a pencil into the hub and rotate clockwise as shown below:

Tape Supply Reel

Tape Take-up Reel

5. A leader tape is provided at the beginning on each cassette. There is no recording on this area,

so it is necessary to let the tape run for about five seconds to clear the head.

6. Keep the tape head clean since a dirty head can cause distorted sound or improper tape speed.

Depress the Cassette Play Button (# 28) and use a small cotton swab with tape head cleaner or

alcohol to clean the tape head, capstan and pinch roller as shown below:

Pinch Roller

Capstan

Playback Head

AUX IN OPERATION

This CD Player provides the AUX IN JACK to enjoy your iPod, MP3 PLAYER MUSIC.

1. Connect the headphone jack of your external device and the AUX IN jack (# 18) located on the

back of this CD player. (The connection cable is not included.)

2. Turn on the CD player and it will enter the AUX function mode once the AUX IN jack is plugged.

3. Start to play your iPod, MP3 player or other audio device.

4. Slowly adjust both the volume controls on your CD player and the external device.

5. Turn off your iPod, MP3 player etc. when finish listening. Turn the CD player off and unplug the

AUX IN jack.

Remark: Once the AUX IN jack is plugged, the CD player will enter the AUX mode automatically no matter the FUNCTION/POWER Switch (# 19) is in RADIO, TAPE or CD mode.

Remember to disconnect the connection cable from the CD player after use in order to be able to listen to the RADIO, TAPE or CD player again.

7

CARE AND MAINTENANCE

1. Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.

2. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.

3. Keep your unit away from heating appliances and sources of electrical noise such as

fluorescent lamps or motors.

4. If drop-outs or interruptions occur in the music during CD play,

or if the CD fails to play at all, its bottom surface may require cleaning.

Before playing, wipe the disc fromthe center outwards with a good soft cleaning cloth.

COMPLIANCE WITH FCC REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio technician for help.

WARNING:

Changes or modifications to this unit not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment.

8

TROUBLESHOOTING GUIDE

If you experience difficulties in the use of this music system please check the following or call 1 800 777 5331 for Customer

Service.

Symptom

Noise or sound distorted on AM or

FM broadcast

AM or FM no sound

CD player will not play

CD skips while playing

Intermittent sound from CD Player

Cassette Player no sound

Sound distorted

Speed varies

Cassette Recorder will not record

Distorted sound on playback

Possible Cause

Station not tuned properly for AM or FM.

FM: Telescopic antenna is not extended.

AM: The bar antenna is not positioned correctly

Unit not in RADIO function mode.

Volume set at minimum

Unit not in CD function mode.

CD is installed incorrectly.

It the CD is self-compiled, the media used may not be compatible with the player.

Batteries become exhausted

Disc is dirty or scratched.

Solution

Retune the AM or FM broadcast station.

FM: Extend FM Telescopic antenna.

AM: Reposition the unit until the best reception is obtained.

Slide Function/Power Switch to RADIO position

Increase Volume

Select CD function mode.

Insert CD with label side up.

Use better quality blank media and retest.

Replace all batteries with new ones.

Wipe CD with clean cloth or use another disc.

Clean or replace the defective disc

Use a CD-lens cleaning disc to clean the lens

Dirty or defective disc

Dirty pick up lens

Player is subject to excessive shock or vibration

Unit not in TAPE function mode

Volume at minimum

Dirty tape head

Tape old or worn

Dirty roller and capstan

Prevention tab removed

Defective tape or dirty tape head

Slide Function/Power Switch to TAPE

Increase volume

Clean the head

Clean the headReplace the tape

Clean roller and capstan

Cover hole with tape

Replace tape or clean tape head

9

90 DAY LIMITED WARRANTY AND SERVICE

VALID IN THE U.S.A ONLY

SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective materials or factory workmanship for a period of 90 days from the date of original customer purchase and provided the product is utilized within the U.S.A. This warranty is not assignable or transferable.

Our obligation under this warranty is the repair or replacement of the defective unit or any part thereof, except batteries, when it is returned to the SPECTRA Service Department, accompanied by proof of the date of original consumer purchase, such as a duplicate copy of a sales receipt.

You must pay all shipping charges required to ship the product to SPECTRA for warranty service. If the product is repaired or replaced under warranty, the return charges will be at SPECTRA’s expense.

There are no other express warranties other than those stated herein.

This warranty is valid only in accordance with the conditions set forth below:

1. The warranty applies to the SPECTRA product only while:

a. It remains in the possession of the original purchaser and proof of purchase is demonstrated.

b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the

descriptions and warnings covered within the user manual or non-SPECTRA approved

modifications.

c. Claims are made within the warranty period.

2. This warranty does not cover damage or equipment failure caused by electrical wiring not in

compliance with electrical codes or SPECTRA user manual specifications, or failure to provide

reasonable care and necessary maintenance as outlined in the user manual.

3. Warranty of all SPECTRA products applies to residential use only and is void when products are

used in a nonresidential environment or installed outside the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the unit carefully and send it freight prepaid to SPECTRA at the address shown below. IF THE UNIT IS RETURNED WITHIN THE

WARRANTY PERIOD shown above, please include a proof of purchase (dated cash register receipt) so that we may establish your eligibility for warranty service and repair of the unit without cost. Also include a note with a description explaining how the unit is defective. A customer service representative may need to contact you regarding the status of your repair, so please include your name, address, phone number and email address to expedite the process.

IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $25.00 to cover the cost of repair, handling and return postage. All out of warranty returns must be sent prepaid.

It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at [email protected] for updated information on the unit requiring service. In some cases the model you have may be discontinued, and SPECTRA reserves the right to offer alternative options for repair or replacement.

SPECTRA MERCHANDISING INTERNATIONAL, INC.

4230 North Normandy Avenue,

Chicago, IL60634, USA.

1-800-777-5331

To register your product, visit the link below to enter your information.

http://www.spectraintl.com/wform.htm

Printed in China

10