OKI PT330 330, 331 POS printer User's Guide
Below you will find brief information for POS printer PT330 330, POS printer PT330 331. The PT330-331 are thermal POS printers, suitable for a variety of applications, including retail, hospitality, and healthcare. They offer high-speed printing, a variety of interface options, and a compact design. The printers are easy to set up and use, and they come with a variety of features, including automatic paper cutting, a paper near-end sensor, and a drawer kick connector.
Advertisement
Advertisement
1
2
Table of Contents
1. Appearance and Name of Components ························································5
1-1. Names of Components ································································ 5
1-2. Package Contents······································································· 6
3-1. Paper Width ················································································ 8
3-2. Paper Thickness ········································································· 8
3-3. Roll Paper··················································································· 8
3-4. Recommended Thermal Paper ····················································· 9
4-1. Connecting the Interface Cable (to the printer) ·························· 11
4-2. Connecting the Interface Cable (to the PC)································ 13
4-3. Connecting the Drawer Kick Cable············································· 15
4-4. Connecting the AC Adapter and Cable ······································· 16
4-5. Removing the AC Adapter ························································· 19
4-6. Installing the Printer·································································· 20
4-7. Power On ················································································· 24
4-8. Installing the Printer Software ··················································· 25
5-1. Opening the Top Cover ····························································· 26
5-2. Paper Width Setting (Width: 58mm / 80mm) ······························· 28
5-3. Setting the Paper······································································ 30
5-4. Closing the Top Cover······························································· 32
6-1. Control Panel············································································ 33
6-2. Error Indications ······································································· 34
7. Paper Jam Prevention and Removal ··························································36
7-1. Paper Jam Prevention······························································· 36
7-2. Paper Jam Removal ·································································· 36
7-3. If the Top Cover Does Not Open ··············································· 37
8-1. Problems at Power-on and Other Errors ···································· 40
8-2. Cutter Problems ······································································· 40
8-3. Printing Problems······································································ 41
3
9. Special Mode (Test Print, Setup Menu...)····················································42
9-1. Test Print ················································································· 42
9-2. Changing the Setup··································································· 44
9-3. Setup Settings ·········································································· 54
9-4. HEX Dump ················································································ 60
9-5. Command Trace········································································ 61
9-6. Sample Print ············································································· 62
10-1. Cleaning Paper Holder and Paper Transport ····························· 67
10-2. Cleaning the Platen Roller························································ 68
10-3. Cleaning the Thermal Head ······················································ 69
11-1 Serial Interface ········································································ 70
11-2. USB Interface ········································································· 73
11-3. LAN Interface ········································································· 74
11-4. Drawer Kick Connector ··························································· 76
11-5. Power Specifications ······························································· 78
12-1. General Specifications····························································· 79
12-2. Cutter Specifications······························································· 82
12-3. Roll Paper Supply Specifications ·············································· 82
12-4. Interface Specifications ··························································· 82
12-5. Environment Specifications······················································ 83
12-6. Reliability Specifications ·························································· 84
13-1. Paper Related Precautions ······················································ 85
13-2. Cutter Related Precautions ····················································· 86
13-3. Barcode/2D Code Printing Precautions···································· 86
13-4. USB Interface Usage Precautions ············································ 87
13-5. Installation Precautions ··························································· 87
13-6. Modular Type Connector Usage Precautions ···························· 87
4
1. Appearance and Name of Components
1-1. Names of Components
Standard Model
Top Cover
Middle Cover
Front Cover
Release Lever
Control Panel
Power Switch
Built-in Power Supply Model
•
Cover
Opens to replace paper.
•
Lever
Used for opening the top cover.
•
Power Switch
Turns the printer power ON/OFF.
•
AC Inlet
Control Panel
Contains switches for operating the printer and LEDs that indicate the printer status.
•
Cover
This can be removed in case of cutter jam or when the top cover does not open.
•
Inlet
Plug in the AC power supply cable here.
5
1-2. Package Contents
CD
Safety warranty sheet
Rubber Feet
(For vertical installation)
AC Adapter
(Standard Model)
6
Instruction sheet
Thermal Paper
58mm Width Separator
Power cable
2. AC Adapter
Only use the AC adapter specified below.
Item No.
AC Adapter KA02951-0120
Remarks
Input : 100 to 240V AC, 50-60Hz
Output : DC24V±5%,1.5A
Caution: Only use authorized AC adapters.
Caution: Do not use any other bundled AC adapter other than designed for this printer.
7
3. Paper Specifications
Only use the thermal paper roll specified below.
3-1. Paper Width
• 80mm paper
80
mm
0
1 .
0
• 58mm paper
58
mm
0
1 .
0
3-2. Paper Thickness
• 65 - 85μm
3-3. Paper Roll
• Outside diameter:
φ83mm or less
• Core diameter: φ12±0.5mm (inside) / φ18±0.5mm (outside)
• Printing surface: outer surface of the roll
• Treatment of end of paper: The roll paper must not be glued to the core.
The end of the paper must also not be folded back.
Caution: Do not use rolls that have rough sides or sides from which pieces of paper extrude. Such paper may cause unstable paper feeding, resulting in printer trouble.
8
3-4. Recommended Thermal Paper
Manufacturer Product
Name
Quality Characteristic
Oji Paper Co.,
Ltd.
PD160R
PD190R
Nippon Paper
Industries
Co., Ltd.
TF60KS-E
TP60KS-F1
TF50KS-E
TF62KS-E
Monochrome thermal paper
(high-grade preservation type )
Monochrome thermal paper
(mid-grade preservation type )
Monochrome thermal paper
(normal type)
Monochrome thermal paper
(mid-grade preservation type)
Monochrome thermal paper
(normal type)
Monochrome thermal paper
(normal type)
Paper
Thickness
75μm 100%
75μm 100%
75μm
75μm 100%
65μm 100%
85μm 100%
Caution: Using non-recommended paper may cause printer head
damage, bad printing quality, etc.
Density
100%
9
4. Preparation
No printer cable is provided with the product. Obtain a printer cable suitable for the product interface. If you have any question, consult your dealer. Before connecting or disconnecting cables, make sure of the following:
(1) The power to the printer and all other devices connected to the printer is turned off.
(2) The AC adapter power cable has been unplugged from the outlet.
Caution: When connecting cables or moving the printer, hold the middle part of the printer cover on both sides. Holding the top cover may cause it to open.
Top Cover
Middle Cover
10
4-1. Connecting the Interface Cable (to the printer)
4-1-1 Printers with serial and USB interfaces
Standard Model
USB Interface Cable Type-B
* Connect the printer to a PC through this connector.
Serial Interface Cable
* Use the screws to secure it in place after connection.
Built-in Power Supply Model
USB Interface Cable Type-B
* Connect the printer to a PC through this connector.
Serial Interface Cable
* Use the screws to secure it in place after connection.
Power Connector
Drawer Kick Connector
USB Interface
Type-B Connector
Serial Interface
Connector
Caution: Do not connect both the serial and USB interfaces at the same
time.
11
4-1-2 Printers with LAN interfaces
Standard Model
LAN Interface Cable
Built-in Power Supply Model
LAN Interface Cable
Power Connector
LED DIP Switch
LAN Interface
Connector
Drawer Kick Connector
Caution: Do not touch the DIP switches during normal use. This may change the network settings, disabling normal printing.
Caution: If the device is installed vertically, the LAN cable may be un-usable due to its shape. Please check before installing.
12
4-2. Connecting the Interface Cable (to the PC)
4-2-1 Serial Interface
(1) Connect the connector of serial interface cable to the serial port on the computer as shown in the figure.
4-2-2 USB Interface
(1) Connect the connector of USB interface cable to the USB port on the computer as shown in the figure.
13
4-2-3 LAN Interface
(1) Connect the connector of LAN interface cable to the LAN port on the computer as shown in the figure.
14
4-3. Connecting the Drawer Kick Cable
Standard Model
Drawer Kick Cable
Built-in Power Supply Model
Drawer Kick Cable
Caution: This product uses a special-purpose modular connector for the cash drawer. Do not attempt to use other types of connectors such as public telephone connectors.
15
4-4. Connecting the AC Adapter and Cable
Standard Model
(1) Connect the cable connector of the AC adapter to the power connector.
AC Adapter
Connector
Power Connector
Flat Side
Cable Connector
Power Cable
AC Inlet
AC Adapter
Caution: Before connecting the AC adapter, turn off the power switches on the printer and all the devices connected to the printer. Also, remove the plug of the AC adapter power cable from the outlet.
Caution: Use the specified AC adapters.
Caution: Perform the adapter connection with the device placed vertically for easy operation.
Caution: As the connector is clipped in place after insertion in order to prevent it from falling off, when performing insertion, (1) grip the cable base with one hand, (2) slide the outer part of the
connector upwards with the other hand (3) and push in until it
locks into place.
①
Cable Base
②
③
The Outer Section of the Connector
16
(2) Confirm that the cable is locked in place by gently pulling on the cable base after connection.
Cable Base
(3) Connect the power connector to the AC inlet of the AC adapter.
The AC Inlet of the AC Adapter
Power Cable
(4) Insert the plug of the power cable into the outlet.
17
Built-in Power Supply Model
(1) Connect the power connector to the AC inlet.
AC Inlet
Power Cable
Caution: switches on the printer and all the devices connected to the printer. Also, remove the plug of the power cable from the outlet.
Caution: vertically for easy operation.
Caution: If the device is installed vertically, use a right-angled power cable.
(2) Insert the plug of the power cable into the outlet.
18
4-5. Removing the AC Adapter
To remove the cable of the AC adapter, pull it while gripping the connector section on the cable side as shown in the following figure. The lock is released, making it easy to remove. Forcibly pulling the cable will damage the connector section.
The Cable Connector
Caution: Before removing the AC adapter, turn off the power switches on the printer and all the devices connected to the printer. Also, remove the plug of the AC adapter power cable from the outlet.
Caution: Perform adapter removal with the device placed vertically for easy operation.
19
4-6. Installing the Printer
Both horizontal installation (the paper exit is on the topside) and vertical installation (the paper exit is on the front side) orientations are available.
In the case of vertical installation, attaching the optional splash-proof cover can protect the printer from water.
The printer can also be fixed to the wall by using the optional wall-hanging bracket.
Horizontal Installation
Vertical Installation
If the printer is installed vertically, stick the rubber feet (included in the package) into the round indents on the printer rear cover.
Rubber Feet
Caution: Before sticking on the rubber feet, wipe off any dirt inside the indents.
20
Splash-proof Cover (Optional)
Mount the splash-proof cover at the top when the printer is installed vertically.
Splash-proof Cover
Caution: The splash-proof cover is used only for vertical installation.
21
Wall Hanging Bracket (Optional)
To fix the printer to a wall, follow the procedures below:
(1) Mount two metal screws (thread diameter: Φ4, head diameter: Φ7) on the wall, spaced 62mm apart in a horizontal line, such that the length of each screw entering the wall is at least 10mm and the length protruding outside is
2-4mm.
62mm
7~9mm
2~4mm
More than or equal to 10mm
4mm
Caution: In order to firmly fix the printer, mount the wall hanging bracket onto a wooden, concrete or metal wall. It is recommended that the wall thickness should be 10mm or more.
Use metal screws.
The screws mounted on the wall are required to have a pull-out strength of 150N (15.3kgf) or more.
Caution: The wall hanging bracket can be used only for printers that use an external AC adapter (Standard Model).
22
(2) Attach the wall hanging bracket to the printer and fix it securely with the enclosed screws.
Wall Hanging Bracket
(3) Align the holes of the wall hanging bracket with the screws mounted to the wall and hang the printer securely.
Screw Head Section
23
4-7. Power On
(1) Connect to the power cable according to 4-3 above.
(2) Turn on the power switch at the side of the printer.
After turning the power on, the POWER LED on the control panel will light up.
Standard Model
Control Panel
Power Switch
Built-in Power Supply Model
Control Panel
Power Switch
24
4-8. Installing the Printer Software
Refer to the "Installation Guide"(*1) in the enclosed CD for instructions on installing the printer driver and utility software.
*1: \Manuals\PT330-331_InstallGuide1_en.pdf
The "Installation Guide" can also be viewed by loading the CD in your PC's
CD drive and selecting "Manuals" on the "Setup" screen that appears.
25
5. Inserting Paper
5-1. Opening the Top Cover
(1) Pull the release lever in the direction of the arrow, and then open the top cover.
Release Lever
Top Cover
Caution: Lift the cover until it is vertical so that it will stay open.
Part A
Part C
Part B
The fulcrum point of top cover
Caution: To open the cover, use either side of part C to hold the printer steady and use part A or part B to lift the cover.
To prevent your fingers being pinched, please do not touch the area around the top cover hinge
.
26
Front part of Printer
(Shaded part)
Caution: When using printer vertically, steady the front part of the printer
(shaded part in the above picture) to open the top cover.
27
5-2. Paper Width Setting (Width: 58mm / 80mm)
As the factory setting for paper width is 80mm, follow the instructions in "5-3.
Setting the Paper" to set the paper roll when using 80mm paper.
When using 58mm paper, first attach the separator in accordance with the instructions in "5-2-1. Attaching the Separator" and then set the paper roll.
Also, follow the instructions in "9-2. Changing the Setup" to set the "Paper
Width" in the printer setup to "58mm/35columns" or "58mm/32columns".
Caution: Do not switch from the 58mm width paper to 80mm width paper when printing is in progress. When using narrow-width paper, a part of the thermal head may directly come in contact with the platen roller without any paper present. This causes the head to wear down, resulting in poor printing quality.
In addition, as the cutter blade also works on sections without paper, the cutter blade may wear down, resulting in a bad cut.
Caution: As the thermal head may be damaged by static electricity, do not touch the thermal head except for cleaning.
Thermal Head
Roll Holder
28
5-2-1 Attaching the
Separator
(1) Align the three lugs of the supplied 58mm width separator with the corresponding holes on the printer body, then push it into place.
58mm Width Separator
Setting Hole
Caution: Push the plate until it locks with a clicking sound and confirm
that the top side of the separator is horizontal.
Caution: When moving the separator follow the instructions in the
Special Mode section to set the paper width and align it with the printing area.
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
29
5-3. Setting the Paper
(1) In the case of a new roll of paper, remove the glued portion and tape on the paper roll.
When replacing the roll paper, first remove the old paper core.
Caution: Since the glued portion of the paper should not be printed on, remove about one turn (about 30 cm) of the roll paper from the beginning so that none of the remaining paper has glue on it.
Any adhesive or other matter remaining from the glue may adhere to the thermal head and cause a problem, such as voids on printouts. Therefore, do not forget to remove the glued portion of the paper.
(2) After inserting the new roll of paper with the orientation shown, pull the end of the paper in the direction indicated by the arrow [1].
Top of Cover
[1]
Platen Roller
Caution: Pull the end of the paper so that it passes over the top of the cover.
Caution: Do not damage or dent the platen roller.
Dents on the platen roller will cause gaps in the printing and/or line feed failure.
30
Caution: Setting the paper as shown in the following figures may cause paper or printing jams.
The paper does not pass over the top of the cover.
The paper has been set incorrectly.
Caution: Do not use deformed roll paper. Using rolls such as those shown below may cause trouble such as paper or printing jams.
Caution: If the roll paper is loose (slack) as shown below, remove the slack before using the roll. Using without removing the slack may cause paper or printing jams, or result in failure to detect the paper near end condition.
31
5-4. Closing the Top Cover
Set the paper correctly and carefully close the top cover.
Push
Top Cover
Caution: Set the paper correctly. Closing the top cover while the paper is skewed may cause a paper jam or messy printing.
Caution: When closing the top cover, close it securely by pressing around the central position (shown by the arrow in the figure) until you hear a clicking sound. If the cover has not locked into place, the printer may not function.
Front part of Printer
(Shaded part)
Caution: When the printer is mounted vertically, use the front of the printer (shaded part in the above picture) to hold it steady when opening the top cover.
32
6. Control Panel
6-1. Control Panel
POWER LED(
)
If the power switch is turned on and the printer is supplied with power, this
LED will light up.
ERROR LED(
)
This LED lights up or blinks to indicate an error.
FEED Button
Pressing this button once causes the printer to feed the paper by an amount equivalent to one line.
Holding it down feeds the paper continuously.
Rear of the Printer
Caution: When the printer is mounted vertically, always hold the rear of the printer when you press the FEED button to keep the printer steady and prevent it from falling over.
33
6-2. Error Indications
Recoverable errors
Error State
No paper
Paper end
Cover open
Cutter jam
LED Lamp
POWER (
)
ERROR (
)
POWER (
)
ERROR (
)
POWER (
)
ERROR (
)
Error State
Paper near end
Head hot
LED Lamp
POWER (
)
ERROR (
)
POWER (
)
ERROR (
)
Blinking Pattern
Constantly on
Constantly on
Constantly on
Constantly on
Constantly on
Constantly on
Blinking Pattern
Constantly on
Remains unchanged.
34
Unrecoverable errors
Error State
Internal error
LED Lamp Blinking Pattern
POWER(
)
——
—
—
ERROR(
)
—————
Repetition of two blinks of the
lamp and one blink of the
lamp
Head not installed
POWER(
)
——
—
—
—
ERROR(
)
———————
Low voltage
Over voltage
Watchdog timer error
Repetition of three blinks of the
lamp and one blink of the
lamp
POWER(
)
——
—
—
—
—
ERROR(
)
——————————
Repetition of four blinks of the
lamp and one blink of the
lamp
POWER(
)
——
—
—
—
—
—
ERROR(
)
————————————
Repetition of five blinks of the
lamp and one blink of the
lamp
POWER(
)
——
—
—
—
—
—
—
—
—
ERROR(
)
——————————————————
Repetition of eight blinks of the
lamp and one blink of the
lamp
35
7. Paper Jam Prevention and Removal
7-1. Paper Jam Prevention
Do not touch the paper while it is coming out or before cutting is complete.
Pressing or pulling the paper with your hand while it is coming out may cause a paper jam, bad cut, or bad line feed.
7-2. Paper Jam Removal
In case of a paper jam, remove the paper as follows:
(1) Turn off the power switch to disconnect the printer from the power.
(2) Pull the release lever towards you, and then open the top cover.
If the top cover does not open, refer to the instructions in "7-3. If the Top
Cover Does Not Open" to remove the cutter jam.
(3) Press the printer and remove the jammed paper.
Caution: When removing paper, remove the paper slowly without pulling it forcibly.
Caution: As the thermal head may be damaged by static electricity, do not touch the thermal head. Also, do not touch the thermal head as it may still be hot after printing.
(4) Set the paper correctly and carefully close the top cover.
Caution: Set the paper correctly. Closing the top cover while the paper is skewed may cause a paper jam or messy printing.
Caution: When closing the top cover, close it securely by pressing around the central position until you hear a clicking sound. If the cover has not locked into place, the printer may not function.
(5) Turn on the power switch . Also, at this time confirm that the ERROR lamp has turned off.
Caution: As printing data cannot be received while the ERROR lamp is on, firmly close the top cover.
36
7-3. If the Top Cover Does Not Open
When the printer has stopped with the cutter blade exposed due to some abnormality such as a paper jam, the top cover will not open.
In such a case, instead of opening it forcibly, perform the following steps:
(1) Turn off the power switch to disconnect the printer from the power.
(2) Turn the power on again. This causes the cutter to operate and may clear the paper jam.
(3) Pull the release lever toward you to check whether the top cover opens. If so, turn the power off again and follow the instructions from step (6) to clear the paper jam.
If the top cover still cannot be opened after the power is turned on, turn the power off again and follow the instructions from step (4) to clear the paper jam.
(4) Remove the front cover by lifting it as shown by the arrow.
Top Cover
Front Cover
37
(5) Lift the protective sheet as indicated by arrow A and rotate the cutter gear in the direction indicated by arrow B while pulling the release lever toward you.
If the auto-cutter blade fails to move despite rotating the cutter gear and the top cover still will not open, pull the release lever toward you and rotate the cutter gear in the opposite direction (indicated by arrow C) until the top cover is able to open.
A
Cutter Gear
Auto-cutter blade is protruding
Protective Sheet
B
C
Cutter Motor
Auto-cutter blade is retracted
Release Lever
Top cover cannot open
Top cover can open
Top Cover
Caution: Do not the touch the cutter motor, as it may still be hot after printing.
Caution: Do not touch the auto cutter, as its blade end is sharp and
dangerous.
Caution: When you cannot open Top Cover with rotating Cutter Gear to either direction, call your service provider.
38
(6) Open the top cover and remove the jammed paper while holding the printer steady.
Caution: When removing paper, remove the paper slowly without pulling it forcibly.
Caution: As the thermal head may be damaged by static electricity, do not touch the thermal head. Also, do not touch the thermal head as it may still be hot after printing.
(7) Set the paper correctly and carefully close the top cover.
Caution: Set the paper correctly. Closing the top cover while the paper is skewed may cause a paper jam or messy printing.
Caution: When closing the top cover, close it securely by pressing around the central position until you hear a clicking sound. If the cover has not locked into place, the printer may not function.
(8) Turn on the power switch. Also, at this time confirm that the ERROR lamp has turned off.
Caution: As printing data cannot be received while the ERROR lamp is on, firmly close the top cover.
39
8. Troubleshooting
This section provides solutions for printer malfunctions and print quality problems.
8-1. Problems at Power-on and Other Errors
Symptom Cause Solution
Although the power has been turned on, the
POWER lamp on the control panel does not light up and the printer does not start.
(1) The power cable is disconnected.
(2) The AC adapter is not plugged in.
(1) Connect the power cable.
* Refer to 4-3. Connecting the AC
Adapter and Cable.
(2) Connect the connector of the AC adapter.
* Refer to 4-3. Connecting the AC
Adapter and Cable.
The ERROR lamp on the control panel lights up and the printer does not work.
(1) There is no paper in the printer .
(2) The top cover is not completely closed.
(3) The thermal head is excessively hot.
(1) Set the paper.
* Refer to 5. Inserting Paper.
(2) Close the top cover completely.
* Refer to 5. Inserting Paper.
(3) Wait for the thermal head to cool down.
8-2. Cutter Problems
Symptom Cause
The paper is not cut.
The cutter does not return to its correct position.
(1) The cutter blade is damaged or worn out.
(2) Paper fragments or other foreign matter are stuck around the cutter or the sliding section.
Paper fragments or other foreign matter are stuck around the cutter or the sliding section.
Solution
(1) Turn off the power and request repair.
(2) Remove the paper fragments or other foreign matter.
Remove the paper fragments or other foreign matter.
40
8-3. Printing Problems
Symptom Cause
The printer does not print.
(1) The interface cable is disconnected or broken.
(2) The printer setup is not correct.
Solution
(1) Connect the interface cable correctly, or replace it.
* Refer to 4-1. Connecting the
Interface Cable
(2) Amend the setting.
Print is too dark or blurred.
Print is too faint.
Printing is uneven.
Vertical marks appear on the printout.
(1) Print density setting in the printer setup is incorrect.
(2) The thermal head is damaged.
(1) Print density setting in the printer setup is incorrect.
(2) The thermal head is damaged.
* Refer to 9-2. Changing the Setup.
(1) Set the printer at the suitable print density and/or print speed for the print paper.
* Refer to 9-2. Changing the Setup.
(2) Turn off the power and request repair.
(1) Set the printer at the suitable print density and/or print speed for the print paper.
* Refer to 9-2. Changing the Setup.
(2) Turn off the power and request repair.
Paper fragments or other
(1) Check and clean the thermal head. foreign matter are stuck to the
* Refer to 10-3. Cleaning the heating elements of the thermal
Thermal Head head.
(2) The setting of the printer setup is incorrect.
(2) Set the printer at the suitable print density and/or print speed for the print paper. Amend the setting.
* Refer to 9-2. Changing the Setup.
(3) Foreign matter is stuck on the platen roller.
(3) Remove the foreign matter from the platen roller.
(4) The thermal head is damaged.
* Refer to 10-2. Cleaning the Platen
Roller
(4) Turn off the power and request repair.
(1) Foreign matter is stuck in or dropped into the paper transport.
(2) Foreign matter is stuck on the thermal head.
(3) The thermal head is damaged.
(1) Clean the paper transport.
* Refer to 10-1. Cleaning Paper
Holder and Paper transport
(2) Clean the thermal head.
* Refer to 10-3. Cleaning the
Thermal Head
(3) Turn off the power and request repair.
41
9. Special Mode (Test Print, Setup Menu...)
9-1. Test Print
Ensure that paper is set in the printer. Turn off the power switch on the printer, then turn it on again while pressing the FEED button on the control panel. This outputs the following printout.
Caution: Press and hold the FEED button until the printer starts
printing.
Special Mode
1.Test Print
2.Setup Menu
3.Hex Dump
4.Command Trace
5.Sample Print
6.End
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
Then Press the FEED button once (select 1. Test Print) to start a test print.
The printer automatically cuts the paper and stops after performing a set amount of printing. To terminate the test print while in progress, press the FEED button.
This cuts the paper and terminates printing.
42
Test Print (Example)
PT330-331 Ver1.0
123456
Memory Switch 1
Power On Status
Receive Buffer
Busy Condition
Receive Error
Auto LF
DSR(#6)Reset
INIT(#25)Reset
USB Soft Reset
Memory Switch 2
Cover Open Error
Error
Batch (COM IF)
Batch (Other IF)
Serial Number
ASB
Font-B
Paper Width
Max Speed
Print Density
Hardware
Error Alert
Buzzer Interval
Buzzer Repetition
Graph/User NV-MEM
Cut at CoverClose
PNE Detect
Interface
Baudrate
Format
Protocol
USB
Enable
4KByte
Bufferfull
Disable
Disable
Disable
Enable
Auto Recovery
Auto Recovery
Enable
Disable
Disable
Enable
Mode1
80mm/48columns
180mm/s
100%
None
Pattern 2
Three
384KB/192KB
Disable
Enable
115200BPS
8NONE1
DSR/DTR
Printer
! " # $ % & ' ( ) * + , - . / 0 1 2 3 4
5 6 7 8 9 : ; < = > ? @ A B C D E F G H I
J K L M N O P Q R S T U V W X Y Z [ \ ] ^
_ ~ a b c d e f g h I j k l m n o p q r s
43
The Firmware Number and Firmware
Version vary according to the model.
“123456”is an example serial number.
9-2. Changing the Setup
This section explains how to setup the printer without using a PC.
Alternatively, when the printer is connected to a Windows PC, the settings can be changed using the utility software on the enclosed CD.
For instructions on installing and using the utility software, refer to the
"Installation Guide" and "Utility User's Guide" located in the Manuals folder of the CD.
•
Installation Guide : PT330-331_InstallGuide1_en.pdf
•
Utility User's Guide : PT330-331_UtilityGuide_en.pdf
The "Installation Guide" and "Utility User's Guide" can also be viewed by loading the CD in your PC’s CD drive and selecting "Manuals" on the "Setup" screen that appears.
Setting Example Select a higher print density
Print Density Changed from 100% to 130%
Perform setup as follows:
1. Check the printer state prior to setting.
(1) The power is off.
(2) The paper roll is set.
(3) The cover is closed.
44
2.
Ensure that paper is set in the printer. Turn off the power switch on the printer, then turn it on again while pressing the FEED button on the control panel. This outputs the printout shown in section 9-1.
Then Press the FEED button twice (to select 2. Setup Menu) enters setup mode and prints the following menu.
Setup Menu
1.Setting
2.Setup Print
3.Save & End
4.Default Set
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
45
3. Then Press the FEED button once (to select 1. Setting) enters setting mode and prints the following setting groups.
Setting
1.Memory Switch 1
2.Memory Switch 2
3.Print
4.Hardware
5.Interface
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
46
4. Then Press the FEED button three times (to select 3. Print) selects the
Print group and prints the following setting options.
1.Paper Width
2.Max Speed
3.Print Density
80mm/48columns
180mm/s
100%
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
<Setup Menu>
Continue to press FEED button more than
3 seconds.
47
5. Then Press the FEED button three times (select 3.Print Density) selects the Print Density setting and prints the following Print Density settings.
Print Density
1.70%
2.80%
3.90%
4.100%
5.110%
6.120%
7.130%
100%
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
<Setup Menu>
Continue to press FEED button more than
3 seconds.
48
6. Then Press the FEED button seven times (to select 7. 130%) returns to the Print settings group.
Changed items are displayed in bold and underlined.
1.Paper Width
2.Max Speed
3 . P r i n t D e n s i t y
80mm/48columns
180mm/s
1 3 0 %
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
<Setup Menu>
Continue to press FEED button more than
3 seconds.
To exit to the previous level (<Return>)
⇒ Go to Section 7-1
To exit directly to the setup menu (<Setup Menu>)
⇒ Go to Ssection 7-2
49
7-1. Exiting to Previous Level
Hold the FEED button down for 1 second or more until the buzzer sounds twice.
Release the FEED button after the buzzer sounds.
This returns to the previous level and prints the Setting group options.
Setting
1.Memory Switch 1
2.Memory Switch 2
3.Print
4.Hardware
5.Interface
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
50
Hold down the FEED button again for 1 second or longer until the buzzer sounds twice. Release the FEED button after the buzzer sounds.
This returns to the previous level and prints the Setup Menu.
Setup Menu
1.Setting
2.Setup Print
3.Save & End
4.Default Set
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
Proceed to step 8.
51
7-2. Exiting Directly to Setup Menu
Hold the FEED button down for 3 seconds or more to return to the Setup
Menu.
Although holding down the FEED button for a long time causes the buzzer to sound twice after 1 second, ignore this and continue to press the FEED button.
After about 3 seconds, the buzzer sounds three times and the following menu is printed.
Setup Menu
1.Setting
2.Setup Print
3.Save & End
4.Default Set
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
<Return>
Continue to press FEED button more than
1 second.
Proceed to step 8.
52
8. Pressing the FEED button three times (to select 3. Save & End) saves the settings, cuts the paper, and then exits setup mode.
Caution: If the power switch of the printer is turned off without selecting "Save & End", any changes made will not be saved.
Checking the Settings
To check that the settings have been applied, follow the instructions in section 9.1 to perform a test print.
The test print includes a list of printer settings. Use this to confirm your changes.
53
9-3. Setup Settings
Setting Groups
Settings Group
1
Memory Switch 1
2
Memory Switch 2
Description
3 Print
4 Hardware
Memory Switch 1 settings
Memory Switch 2 settings
Print settings
Hardware settings
5 Interface Serial and USB interface settings
(This group is not displayed on printers with a LAN interface.)
Setting Items and Detailed Setting Items
(Note) Setup items and the default values depend on the printer model and/or area.
(1) Memory Switch 1 Group
1
2
6 DSR(#6)Reset
7 INIT(#25)Reset
8
Power On Status
Receive Buffer
USB Soft Reset
Specifies Power ON notification.
Specifies receiver buffer size.
Sets the printer as BUSY (data reception not available).
1
2
Specifies what to do when a receive error occurs using the serial interface.
Specifies whether the CR code generates an automatic line feed.
1
2
Specifies whether receiving DSR
(#6) via the serial interface triggers a hardware reset.
1
2
Specifies whether receiving INIT
(#25) via the serial interface triggers a hardware reset.
1
2
Specifies whether a USB Soft Reset triggers a hardware reset when using printer class USB.
1
2
1
2
1
2
1
2
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
45bytes
4Kbytes
Buffer full
Offline/Buffer full
Ignore
Enable
Disable
54
(2) Memory Switch 2 Group
1
Cover Open Error
2
3
4
Error
Batch (COM IF)
Batch (Other IF)
6 ASB
7 Font-B
Recovery method for Cover Open Error during print
What to do at power on or after recovery from error
"Auto Recovery": Perform auto recovery to enable data reception.
"Recovery by CMND": Discard any received data until a reset command is received.
1
2
1
2
Specifies whether to use batch printing for the serial interface
1
2
Specifies whether to use batch printing for the USB or LAN interface
Specifies iSerial Number notification for
USB
"Disable": Returns “0” as the iSerial
Number.
1
2
1
2 serial number as the iSerial
Number
Specifies whether to enable the automatic status transmission function
(ASB: Automatic Status Back)
Specifies the number of columns for font
B (horizontal x vertical)
"Mode1" 10x24
"Mode2" 9x24
1
2
1
2
Auto Recovery
Recovery by CMND
Auto Recovery
Recovery by CMND
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Mode1
Mode2
55
(3) Print Group
1
Paper Width
2
Max Speed
Paper width and number of characters per line
Maximum print speed
The maximum for printing ladder barcodes and two-dimensional codes is 120mm/s.
Print density
The smaller the value the lower the print density.
The higher the value the higher the print density.
1
8
9
6
7
2
3
4
5
3
4
1
2
5
6
7
1
2
3
4
80mm/48columns
80mm/42columns
58mm/35columns
58mm/32columns
100mm/s
110mm/s
120mm/s
130mm/s
140mm/s
150mm/s
160mm/s
170mm/s
180mm/s
70%
80%
90%
100%
110%
120%
130%
56
(4) Hardware Group
1
2
Error Alert
*1
Buzzer Interval
*2
3
Buzzer Repetition
*2
4
5
Graph/User
NV-MEM
Cut at Cover
Close
Whether to sound a buzzer when an error occurs
"None": Does not beep.
"One Time": Beeps four times.
"Continuous": Beeps continuously.
The buzzer tone to use during printing
The buzzer beeps in the following cases during printing:
•
FEED button pressed while cover open
•
Buzzer command received
(ESC p 03h t1 t2 t3)
The number of buzzer beeps during printing
Zero specifies no buzzer.
The buzzer beeps in the following cases during printing:
•
FEED button pressed while cover open
•
Buzzer command received
(ESC p 03h t1 t2 t3)
3
4
1
2
5
6
NV graphic memory size and user NV memory size
Specifies the size of the registration area for graphics images and NV bit images, and the size of the area for storing any user data.
3
4
1
2
1
2
3
3
4
1
2
5
Whether to trigger the cutter when the cover is closed.
1
2
Whether to notify when near the paper end
1
2
None
One Time
Continuous
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Zero
One
Two
Three
Four
Five
384KB/192KB
448KB/128KB
512KB/64KB
576KB/0B
Enable
Disable
Enable
Disable
57
The operation when a "continuous" buzzer tone is output is as follows:
(Note) To stop the buzzer during continuous beeping, press the FEED button.
•
•
Recoverable Error (Excluding Paper Near End)
Continuous beeping of 500mSecON/200mSecOFF
Hardware Error
Continuous beeping of 1000mSecON/500mSecOFF
*2 "Buzzer Interval"
The buzzer patterns are as follows:
•
•
Pattern 1 40msON / 120msOFF
Pattern 2 140msON / 140msOFF
•
•
Pattern 3 200msON / 200msOFF
Pattern 4 10msON / 50msOFF
•
Pattern 5 30msON / 50msOFF
58
(5) Interface Group
1
Baud rate
2
Format
3 Protocol
4 USB
Baud rate for the serial interface
Data format for the serial interface
Buffer control protocol for the serial interface
Class for USB interface
1
2
1
2
3
4
1
2
5
1
4
5
2
3
6
7
2400BPS
4800BPS
9600BPS
19200BPS
38400BPS
57600BPS
115200BPS
7EVEN1
7ODD1
8NONE1
8ENEN1
8ODD1
DSR/DTR
XON/XOFF
Printer
V-COM
(Note) This group is not displayed for printers with a LAN interface.
59
9-4. HEX Dump
Ensure that paper is set in the printer. Turn off the power switch on the printer, then turn it on again while pressing the FEED button on the control panel. This outputs the printout shown in section 9-1.
Pressing the FEED button three times (select 3. Hex Dump) enters HEX dump mode.
This mode prints all the data sent to the printer as hex code. It is useful for checking whether the control codes being sent to the printer by the PC program are correct.
To clear this mode, turn the power switch off and on again.
HEX Dump Print (Example)
Hex Dump
Address Hex ASCII
000000 1B 40 1B 4D 02 1B 74 01 [email protected].
Addre ss
H e x
ASCII
60
9-5. Command Trace
Ensure that paper is set in the printer. Turn off the power switch on the printer, then turn it on again while pressing the FEED button on the control panel. This outputs the printout shown in section 9-1.
Pressing the FEED button four times (select 4. Command Trace) enters command trace mode.
This mode prints all the data sent to the printer in ASCII format (with
ESC/POS command explanations). It can be used to analyze the ESC/POS commands sent to the printer by the PC program.
To clear this mode, turn the power switch off and on again.
Command Trace Print (Example)
Command Trace
<1 B 4 0 :Initialize printer (ESC @)>
<1 B 4 D 0 2 :Set ANK font C (ESC M n)>
<1 B 7 4 8 0 :Set character code table (ESC t n)>
<1 D 4 2 0 0 :Disable reverse printing (GS B n)>
<1 B 6 1 0 2 :Set justification RIGHT (ESC a n)>
<1 C 2 E :Reset kanji mode (FS .)>
ABC
<0 A :Print and line feed (LF)> a. Undefined commands or commands with abnormal command parameters are treated as errors and printed with background and foreground reversed. b. Meaningless and unnecessary commands are printed with an underline as a warning. c. Command codes are printed in bold.
61
9-6. Sample Print
Ensure that paper is set in the printer. Turn off the power switch on the printer, then turn it on again while pressing the FEED button on the control panel. This outputs the printout shown in section 9-1.
Pressing the FEED button five times (select 5. Sample Print) enters sample print mode.
This mode prints an explanation of FEED button operation, performs a paper cut, and then prints sample patterns. (The FEED button explanation is only printed at the first time.)
" Press FEED button.
Short : Next pattern
Long : Same pattern"
After printing, pressing the FEED button briefly (less than one second) prints the following samples, one at a time.
* "Receipt" "Coupon" "Bar Code" "Receipt" in turn. (Printing pauses after each sample. Press the FEED button to print the next sample.)
Pressing the FEED button for a long time (one second or longer) prints the previous sample again.
62
To clear sample print mode, turn the power switch off and on again.
Sample print mode performs a cut after each sheet is printed.
Sample print mode uses the 80mm or 58mm pattern depending on the paper width setting in setup.
If a recoverable error occurs, the sample print resumes after recovery.
The following page shows examples printouts.
63
<Printing Results of Sample Print, 80mm Pattern>
"Receipt" Pattern "Coupon" Pattern
64
"Bar Code" Pattern
65
<Printing Results of Sample Print, 58mm Pattern>
"Receipt" Pattern "Barcode" Pattern
"Coupon" Pattern
66
10. Regular Cleaning
The print quality may be impaired by paper particles, dust, or other material.
To avoid this problem, remove any paper particles or dust from the paper holder, the paper transport, the platen roller, and the thermal head as described below.
Perform cleaning every six months.
10-1. Cleaning Paper Holder and Paper Transport
(1) Be sure to turn off the printer power.
(2) Open the top cover.
(3) Wipe off any dust, paper particles, glue, or other foreign material from the paper holder and paper transport using a soft, dry cloth.
Paper Holder and Paper Transport
67
10-2. Cleaning the Platen Roller
(1) Be sure to turn off the printer power.
(2) Open the top cover.
(3) Wipe off any dust, paper particles, glue, or other foreign material from the platen roller using a soft, dry cloth.
Platen Roller
Caution: Do not damage or dent the platen roller.
Dents on the platen roller will cause incomplete printing and/or line feed failure.
68
10-3. Cleaning the Thermal Head
(1) Be sure to turn off the printer power.
(2) Open the top cover.
(3) Using an alcohol solvent, remove black paper particles and other residue from the surface of the thermal head.
Thermal Head
Caution: The thermal head can easily be damaged. Clean it carefully using a soft cloth to avoid any damage.
Caution: The thermal head is still hot immediately after printing. Leave it to cool for about ten minutes before cleaning.
Caution: The thermal head may be damaged by static electricity. Take care to avoid exposing it to static electricity.
Caution: Wait until alcohol from the cleaning solvent has thoroughly dried before turning on the printer power.
Caution: Use only alcohol or isopropyl alcohol solvents.
69
11. Interface
11-1 Serial Interface
(1) Transmission Interface Specifications
Transmission
Method
Asynchronous
Line Type
Input/Output
Circuit
Baud Rate
Full duplex
Input: MAX211 Equivalent
Output: MAX211 Equivalent
2400, 4800, 9600, 19200, 38400, 57600, 115200BPS
(Setup Settings)
7 or 8 bits Transmission
Code Type
Transmission
Code Format
Start bits:
Stop bits:
1 bit
1 bit
Data bits: 7 or 8 bits (Setup Settings)
Parity: NONE, ODD, EVEN (Setup Settings)
Mark(1)
ST b0 b1 b2 b3 b4 b5 b6 b7 PT SP
Space(0)
LSB to MSB
Transmission
Sequence
Transmission
Code
Error Control
Connection Line
Length
Protocol
JIS code
Parity check (Setup Settings)
Max. 15m: (When power is supplied from the power connector)
Max. 2m: (When power is supplied from the interface connector)
DSR/DTR, XON/XOFF (Setup Settings)
70
(2) Serial Interface Connector
Pin No. Signal Name Direction
1
Signal Line Name
2 TXD Output Transmit
3 RXD Input Receive
4
5
6
RTS
CTS
DSR
7 SG
Output
Input
Input
Request to Send
Clear to Send
Data Set Ready
8~12 N.C
13 SG2
14 SG2
15~17 N.C
18 +24V
19 +24V
20 DTR
21~24 N.C
25 INIT
-
-
-
No
+24V Ground
+24V Ground
- No
-
-
Mechanical Drive Power
Mechanical Drive Power
Output Data Terminal Ready
- No
Input Forcible Signal
Caution: When the power is supplied from the power connector, ensure the pins shaded in grey are not connected.
Caution: Use a lock screw with an imperial thread on the connector.
71
(3) Connection Cable
The connection setup shown in the following figure is recommended.
Host
FG <
TXD<
RXD<
RTS<
CTS<
DSR<
DTR<
SG <
>FG
>TXD
>RXD
>RTS
>CTS
>DSR
>DTR
>SG
Printer
Caution: Supplying power from the interface connector is prohibited.
72
11-2. USB Interface
(1) Type-B Connector: 4 Pins
Pin No. Signal Name
3
4
1
2
Direction
Caution: Use a shielded USB cable.
Signal Line Name
73
11-3. LAN Interface
(1) LAN Interface Connector
Pin No. Signal Name Direction Signal Line Name
1
2 TX-
3 RX+
4 N.C
5 N.C
6 RX-
7 N.C
(2) LED
8 N.C
1
2
3
No. Meaning
Output
Input
-
-
Input
-
-
-
-
-
-
Description
1
2
10BASE-T Link
Lights up when the connection is recognized as
10BASE-T
100BASE-TX
Link
3 Status
Lights up when the connection is recognized as
100BASE-TX
Lights up for a period of time (50msec) when packets are received
74
(3) DIP Switches
Caution: These switches are for maintenance. During normal usage, leave them all in the OFF state.
No. ON OFF
1
2 Settings Information Initialization -
-
-
1 2 3 4 ON
Procedures for Settings Initialization
1) Turn off the printer power.
2) Set No.2 DIP switch to ON.
3) Turn on the printer power. Initialization takes about five seconds.
4) Turn off the printer power.
5) Set No.2 DIP switch to OFF.
Procedures for Test Print from LAN Board
1) Turn off the printer power.
2) Set No.3 and No.4 DIP switches to ON.
3) As soon as the printer power is turned on, a test print is performed.
4) Turn off the printer power.
5) Set No.3 and No.4 DIP switches to OFF.
Caution: Be careful with DIP switch operations.
75
11-4. Drawer Kick Connector
Pin No. Signal Name Direction
1
2 *DRD1
3 DRSNS1
4 +24V
5 *DRD2
6 SG
Signal Line Name
Output Drawer Kick Drive Signal 1
Input Drawer Sense Signal 1
Output Drawer Kick Drive Signal 2
- Signal Ground
1
6
<Connecting side>
76
<Connection>
Printer
1
2
6
3
4
5
Cable
5
4
3
6
2
4
Drawer 1
Drawer
Open/Close
Drawer Kick
Solenoid
(24Ω or bigger)
Drawer 2
Drawer Kick
Solenoid
(24Ω or bigger)
Caution: The drawer connection cable should be of the shielded type.
Caution: Simultaneous drive from the two drives is not available.
Caution: Specify the ON time and OFF time (t1 and t2) for the drawer using the pulse generation command (ESC p m t1 t2).
Caution: Set the drive duty cycle for the drawer in accordance with the following formula: ON time/(ON time + OFF time)
≤ 0.2
Caution: Always use printer power (connector pin 4) for the drawer power.
Caution: Use a drawer kick solenoid with a resistance value of at least
24
Ω. If it is under 24Ω, the solenoid may be damaged by excess current.
Caution: This product uses a special-purpose modular connector for the cash drawer and customer display connector. Do not attempt to use other types of connectors such as public telephone connectors.
77
11-5. Power Specifications
(1) Rated Input Voltage: 100-240V, 50-60Hz
(2) Rated Input Current: 1.1A
(3) Operating Voltage:
DC24V
±10%
(4) Power Consumption: During standby:
3.0W or less/0.1A on average (Dual Interface)
4.5W or less/0.1A on average (LAN Interface)
During operation: About38W/1.5A on average
(at 24V, 25°C, print density setting 100%, paper width 80mm, print duty 9%)
Note: Drawer Kick Drive Current: Max. 1A
However, do not operate two drawer kick at the same time.
Power Connector Pin Assignment
Pin No.
1
Signal Name
+24V
2 SG
3 N.C
1
3
2
Caution: Use the specified AC adapter for the power supply.
Caution: If our AC adapter is not used (power supply is supplied by the user), problems such as bad print quality, electromagnetic interference, or circuit noise may occur. In such cases, take note of the following points:
· Use an AC adapter whose capacity corresponds to the printing rate that will actually be used.
· Ensure in advance that there are no problems such as static electricity, electromagnetic interference, circuit noise, etc.
78
12. Specifications
12-1. General Specifications
(1) Printing Method: Direct Line Thermal Printing
(2) Print Speed: Maximum 180 mm/s (Monochrome only)
(3) Print Resolution: 8dot/mm (0.125mm)
(4) Relationship between Number of Print Column and Character Size
Body face ((Width)x(Height) dot)
Paper width: 58mm
ANK: Font A
ANK: Font B
ANK: Font C
ANK: Font A
Extension Font
ANK: Font B
Extension Font
ANK: Font A
ANK: Font B
ANK: Font C
32 column printing
32 columns: 12x24
38 columns: 10x24
42 columns: 9x24
48 columns: 8x16
32 columns: 12x24
38 columns: 10x24
42 columns: 9x24
42 columns: 10x24
46 columns: 9x24
52 columns: 8x16
42 columns: 10x24
46 columns: 9x24
Body face ((Width)x(Height) dot)
Paper width: 80mm
42 column printing 48 column printing
42 columns: 12x24
51 columns: 10x24
56 columns: 9x24
64 columns: 8x16
35 column printing
35 columns: 12x24
35 columns: 12x24
48 columns: 12x24
57 columns: 10x24
64 columns: 9x24
72 columns: 8x16
ANK: Font A
Extension Font
42 columns: 12x24 48 columns: 12x24
ANK: Font B
Extension Font
51 columns: 10x24
56 columns: 9x24
57 columns: 10x24
64 columns: 9x24
79
(5) Character Sets
Alphanumeric (95), Extension Graphic (128×20 Page), International
Character (48), Special Character (845)
(6) Character Size
Body face
(Width)x(Height) dot
(Width)x(Height) mm
ANK: Font A
ANK: Font B
ANK: Font C
12 x 24
10 x 24
9 x 24
8 x 16
1.5 x 3.0
1.25 x 3.0
1.125 x 3.0
1.0 x 2.0
ANK: Font A
Extension Font
ANK: Font B
Extension Font
12 x 24
10 x 24
9 x 24
1.5 x 3.0
1.25 x 3.0
1.125 x 3.0
Letter face
(Width)x(Height) dot
(Width)x(Height) mm
11 x 22
9 x 17
9 x 17
8 x 13
1.375 x 2.75
1.125 x 2.125
1.125 x 2.125
1.0 x 1.625
12 x 24
9 x 22
9 x 22
1.5 x 3.0
1.125 x 2.75
1.125 x 2.75
(Note) Print Column, Character Size and Character Sets depend on the printer model and/or area.
80
(7) Outline View
Standard Model
Built-in Power Supply Model
81
12-2. Cutter Specifications
(1) Cutting Method: Partial cut (the paper remains connected at one point)
Caution: Do not use the cutter continuously at a rate exceeding 10 cuts per minute (1 cut per 6 seconds or more). Excessive use may cause a malfunction.
12-3. Paper Roll Supply Specifications
(1) Loading Method: Rolls are loaded manually.
(2) Paper Near End: Detected when the remaining paper length is inadequate.
Caution: Core diameter
φ18mm is supported.
12-4. Interface Specifications
(1) Serial (RS-2332C)
(2) USB (USB 2.0 Full-speed)
(3) LAN (10BASE/100BASE-T)
82
12-5. Environment Specifications
(1) Temperature
Operating Operation Guaranteed at: 0°C - 40°C
Print Quality Guaranteed at: 5°C - 35°C
Non-operating
Transportation or storage (packaging)
-5°C - 60°C
-20°C - 60°C
(2) Humidity
Operating Operation Guaranteed at: 10%-95%RH (no condensation)
Non-operating
Print Quality Guaranteed at: 10%-85%RH (no condensation)
8%-95%RH (no condensation)
Transportation or storage (packaging) 5%-95%RH (no condensation)
(3) Maximum Wet Bulb Temperature 29°C or less
100
30°C /95%
90
80
70
60
50
40
30
20
10
0
Guaranteed
Operating
Range
40°C /65%
0 10 20 30 40 50
Ambient Temperature °C
83
12-6. Reliability Specifications
(1) Printer Life 20 million line-feed
(When the recommended paper of 75μm is used)
(2) Head Life Running Life: 100km
(When the recommended paper of 75μm is used)
Pulse Life: 100 million pulses
(When the recommended paper of 75μm is used)
(3) Cutter Life
Paper Thickness 75μm: 1.5 million cuts
(When the recommended paper of 75μm is used)
65μm/85μm: 1.0 million cuts
84
13. Usage Precautions
13-1. Paper Related Precautions
(1) High printing rates may cause blurred printing. Choose a suitable printing rate to avoid blurring. Alternatively, set a suitable combination of print speed and print density to avoid blurring.
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
(2) Printing characters from a non-standard character set in a thin serif or similar font will result in the characters appearing very faint. Use a bold sans serif font. contraction), feed the paper 1mm (8 dots) or more when restarting printing or after cutting the paper.
(4) In sequential printing, slow data transfer may cause white lines to run across the print, as printing and pausing are repeated alternately. If print quality has priority, use the Batch Print mode ("Batch (COM IF)", "Batch
(OTHER IF)").
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
(5) The top margin can be set to either 12mm or 3mm by a command. If the top margin is set to 3mm, be sure to remove the printed paper each time the printing and cutting operation is completed as rollback of paper takes place before printing. If printed and cut paper is not removed, the partial cut section may be torn or the cut surface may be folded causing a paper jam. Also, use at least 30 mm of paper for each transaction.
(6) Setting a high value for print density (110 % and over) can result in blurred or uneven printing at low temperatures, depending on the printing pattern.
If print quality has priority, print at a lower speed.
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
(7) Do not switch from narrower paper to wider paper (e.g. 58mm to 80mm) when printing is in progress. When using narrow-width paper, a part of the thermal head may directly come in contact with the platen roller without any paper present. This causes the head to wear down, resulting in poor printing quality. In addition, as the cutter blade also works at sections without paper, the cutter blade may wear down, resulting in a bad cut. Do not change paper width when printing is in progress.
85
(8) If the paper has been left in the printer for a long time, it may deform and cause faint printing. Therefore, if the paper has been left for a long time, feed the paper forward by 20-30mm before printing.
(9) If non-recommended paper is used, print quality and/or the thermal head life cannot be guaranteed. In particular, use of paper containing “Na+, K+, or Cl-” may significantly shorten the life span of the thermal head.
(10) Using a non-recommended AC adapter may cause blurred and/or uneven printing, so use only the recommended adapter.
(11) The paper may get marked during paper changing or when the top cover is shut, so feed the paper forward by 20-30mm before printing.
13-2. Cutter Related Precautions
(1) Do not use the cutter continuously at a rate exceeding 10 cuts per minute
(1 cut per 6 seconds or more). Excessive use may cause a malfunction.
(2) Do not remove paper while it is still being cut. Doing so may cause problems such as a paper jam.
(3) If the top margin is set at 3mm, be sure to remove the printed paper each time the printing and cutting operation is completed as roll back of the printer paper takes place before printing. Not doing so may cause problems such as a paper jam.
13-3. Barcode/2D Code Printing Precautions
(1) When using thick paper, the printing speed and density should be adjusted and readability should also be checked before using the printer as thick paper may cause blurring depending on the usage environment and the humidity.
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
(2) For 2D codes, adjust the printing speed and density to obtain a good recognition rate. As readability varies depending on the module width, print density, ambient temperature, type of thermal roll paper, and reader performance, check this before using the printer.
(Refer to 9 Special Mode: 9-2. Changing the Setup.)
86
(3) If a barcode is printed at the top of the printer paper when it is first fed, or at the bottom when paper feeding is completed, readability should be checked as accuracy in paper feeding may become unstable.
13-4. USB Interface Usage Precautions
(1) Connect the printer directly to the host computer.
(2) Be sure to turn on the printer power before printing.
(3) If an error occurs during printing, recover the printer from the error, and then retry printing.
(4) Do not turn off the printer or disconnect the USB cable while printing is in progress. Using the host computer to set Stand-by mode, Sleep mode,
Suspend mode or Pause mode is not recommended.
If the printer does not work properly even after implementing the above, try re-connecting the USB cable or turning on the printer power again. If the printer still does not print properly, restart the host computer.
13-5. Installation Precautions
(1) Use the printer indoors only. Outdoor usage may cause printer malfunction due to dust or other factors.
(2) When connecting a cable to the printer or shifting the position of the printer, perform the operation while holding the middle cover of the printer at the sides using both hands. If you perform the operation holding the top cover, the top cover may open.
13-6. Modular Type Connector Usage Precautions
(1) This product uses a special-purpose modular connector for the cash drawer and customer display connector. Do not attempt to use other types of connectors such as public telephone connectors.
87
88
89
Download
Advertisement
Key features
High-speed printing
Variety of interface options
Compact design
Automatic paper cutting
Paper near-end sensor
Drawer kick connector
Frequently asked questions
Connect the interface cable to the printer and the PC. Refer to the instructions in section 4-1. Connecting the Interface Cable.
Open the top cover, set the paper correctly, and close the top cover. Refer to the instructions in section 5. Inserting Paper.
Turn off the power switch, open the top cover, and remove the jammed paper. Refer to the instructions in section 7. Paper Jam Prevention and Removal.
Enter setup mode by turning on the printer while pressing the FEED button. Refer to the instructions in section 9-2. Changing the Setup.