Red Lion Controls PAXCDC 10, 1C, 20, 2C Serial Communications Card User Manual

PDF

Dokument

Oglas

Bulletin No. PAXCDC-E

Drawing No. LP0402

Released 3/05

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839 www.redlion.net

MODEL PAXCDC -SERIAL COMMUNICATIONS PLUG-IN OPTION CARDS

DESCRIPTION

This bulletin serves as a guide for the installation, configuration and operation of the RS232 and RS485 cards for the PAX family of meters. Only one communication card can be used at a time.

The PAX meter can be fitted with up to three different option cards. The slot bays of the option cards are dedicated to a particular card function. The option card functions are: serial communications, analog output and setpoint output.

Only one card from each function category can be installed into the meter.

INSTALLING AN OPTION CARD

Caution: The option and main circuit cards contain static sensitive components. Before handling the cards, discharge static charges from your body by touching a grounded bare metal object. Ideally, handle the cards at a static controlled clean workstation. Also, handle the cards by the edges only. Dirt, oil or other contaminants that may contact the cards can adversely affect circuit operation.

Warning: Exposed line voltage exists on the circuit boards. Remove all power to the meter AND load circuits before accessing the unit.

1. Remove the main assembly from the rear of the case. Squeeze the finger holds on the rear cover, or use a small screwdriver to depress the side latches to release it from the case. It is not necessary to separate the rear cover from the main circuit card.

2. Locate the option card connector for the type of option card to be installed.

Hold the unit by the rear connector, not the display board, when installing an option card.

3. Install the option card by aligning the option card connector with the slot bay in the rear cover. The cards are keyed by position with different main board connector locations. Be sure the connector is fully engaged and the tab on the option card rests in the alignment slot on the display board.

4. Slide the assembly back into the case. Be sure the rear cover latches fully into the case.

5. Apply the option card label to the bottom side of the meter. Do not cover

the vents on the top surface of the meter. The surface of the case must be clean for the label to adhere properly. Apply the label to the area designated by the large case label.

TOP VIEW

ORDERING INFORMATION

MODEL

PAXCDC

DESCRIPTION

RS485 Serial Communications Output Card with

Terminal Block

Extended RS485 Serial Communications Output

Card with Dual RJ11 Connector

RS232 Serial Communications Output Card with

Terminal Block

Extended RS232 Serial Communications Output

Card with 9 Pin D Connector

PART NUMBER

PAXCDC10

PAXCDC1C

PAXCDC20

PAXCDC2C

SPECIFICATIONS

PAXH Isolation For Both Cards:

Isolation To Sensor Common: 1400 Vrms for 1 min.

Working Voltage: 125 V

Isolation To User Input Common: 500 Vrms for 1 min.

Working Voltage: 50 V

RS485 Communication Card

Type: RS485 multi-point balanced interface

Isolation To Sensor & User Input Commons: 500 Vrms for 1 min.

Working Voltage: 50 V. Not Isolated from all other commons.

Baud Rate: 300 to 19.2k

Data Format: 7/8 bits; odd, even, or no parity

Bus Address: 0 to 99, max 32 meters per line

Transmit Delay: Selectable; 2 - 50 msec or 50 - 100 msec

RS232 Communication Card

Type: RS232 half duplex

Isolation To Sensor & User Input Commons: 500 Vrms for 1 min.

Working Voltage: 50 V. Not Isolated from all other commons.

Baud Rate: 300 to 19.2k

Data Format: 7/8 bits; odd, even or no parity

WIRING CONNECTIONS

RS232 Communications

Terminal Block Connection Figure

Extended Comms Connection Figure

RS232 is intended to allow only two devices to communicate over distances up to 50 feet. Data Terminal Equipment (DTE) transmits data on the Transmitted

Data (TXD) line and receives data on the Received Data (RXD) line. Data

Computer Equipment (DCE) receives data on the TXD line and transmits data on the RXD line. The PAX emulates a DTE. If the other device connected to the meter also emulates a DTE, the TXD and RXD lines must be interchanged for communications to take place. This is known as a null modem connection. Most printers emulate a DCE device while most computers emulate a DTE device.

Some devices cannot accept more than two or three characters in succession without a pause in between. In these cases, the meter employs a busy function.

As the meter begins to transmit data, the RXD line (RS232) is monitored to determine if the receiving device is “busy”. The receiving device asserts that it is busy by setting the RXD line into a space condition (logic 0). The meter then suspends transmission until the RXD line is released by the receiving device.

RS485 Communications

The RS485 communication standard allows the connection of up to 32 devices on a single pair of wires, distances up to 4,000 ft. and data rates as high as 10M baud (the PAX is limited to 19.2k baud). The same pair of wires is used to both transmit and receive data. An RS485 bus is therefore always halfduplex, that is, data cannot be received and transmitted simultaneously.

Transmit

Enable

+5V

33K

( )

(+)

COMM.

15 NC

* OPTIONAL

Terminal Block Connection Figure

Extended Comms Connection Figure

MODULE 7 - S

ERIAL

OMMUNICATIONS

ARAMETERS

(

!"#$%

)

PARAMETER MENU

It is necessary to match the PAX meter’s serial communications parameters to the host’s parameters before communications can be established. This is accomplished by using the PAX front panel keys to enter (:,-8 .

Indicates Program Mode Alternating Display.

Parameter

$%&' "

!"##

Selection/Value

Factory Settings are shown.

METER ADDRESS

%''"

0 to 99

Enter the serial node address. With a single unit on a bus, an address is not needed and a value of zero can be used (RS232 applications). Otherwise, with multiple bussed units, a unique address number must be assigned to each meter.

The node address applies specifically to RS485 applications.

$%&' "

!"##

BAUD RATE

300 1200

600 2400

4800

9600

19200

Set the baud rate to match that of other serial communications equipment.

Normally, the baud rate is set to the highest value that all of the serial communications equipment is capable of transmitting.

%$-.

*+,

ABBREVIATED PRINTING

YES NO

Select abbreviated transmissions (numeric only) or full field transmission.

When the data from the meter is sent directly to a terminal for display, the extra characters that are sent identify the nature of the meter parameter displayed. In this case, select /0 . When the data from the meter goes to a computer, it may be desirable to suppress the node address and mnemonic when transmitting. In this case, set this parameter to 4+5 .

'%)% "

(

DATA BIT

7 8

Select either 7 or 8 bit data word lengths. Set the word length to match that of other serial communication equipment. Since the meter receives and transmits 7-bit ASCII encoded data, 7 bit word length is sufficient to request and receive data from the meter.

1%"

0''

PARITY BIT

Odd EVEN NO

Set the parity bit to match that of the other serial communications equipment used. The meter ignores the parity when receiving data, and sets the parity bit for outgoing data. If no parity is selected with 7-bit word length the meter transmits and receives data with 2 stop bits. (For example: 10 bit frame with mark parity)

01) "

PRINT OPTIONS

YES NO

4+5 - Enters the sub-menu to select those meter parameters to appear in the block print. For each parameter in the sub-menu select 4+5 for the parameter to appear with the block print, and /0 to disable the parameter.

*Setpoints 1-4 are setpoint plug-in card dependent.

Input Value

Max and Min Values

Total Value

Setpoint values*

2/3 4+5 /0

7280 4+5 /0

)9) 4+5 /0

53/) 4+5 /0

Sending Commands and Data

When sending commands to the meter, a string containing at least one command character must be constructed. A command string consists of a command character, a value identifier, numerical data (if writing data to the meter) followed by a the command terminator character * or $.

Command Chart

Command Description

Notes

Node Address

Specifier

Transmit Value (read)

Value change (write)

Reset

Block Print Request

(read)

Address a specific meter. Must be followed by one or two digit node address. Not required when node address = 0.

Read a register from the meter. Must be followed by register ID character.

Write to register of the meter. Must be followed by register ID character and numeric data.

Reset a register or output. Must be followed by register ID character

Initiates a block print output. Registers are defined in programming.

Command String Construction

The command string must be constructed in a specific sequence. The meter does not respond with an error message to illegal commands. The following procedure details construction of a command string:

1. The first 2 or 3 characters consist of the Node Address Specifier (N) followed by a 1 or 2 character node address number. The node address number of the meter is programmable. If the node address is 0, this command and the node address itself may be omitted. This is the only command that may be used in conjunction with other commands.

2. After the optional address specifier, the next character is the command character.

3. The next character is the register ID. This identifies the register that the command affects. The P command does not require a register ID character.

It prints according to the selections made in print options.

4. If constructing a value change command (writing data), the numeric data is sent next.

5. All command strings must be terminated with the string termination characters * or $. The meter does not begin processing the command string until this character is received. See timing diagram figure for differences of

* and $ terminating characters.

Receiving Data

Data is transmitted by the meter in response to either a transmit command

(T), a print block command (P) or User Function print request. The response from the meter is either a full field transmission or an abbreviated transmission.

In this case, the response contains only the numeric field. The meter response mode is established in programming.

Full Field Transmission

Byte

1, 2

4-6

7-18

Description

2 byte Node Address field [00-99]

<SP> (Space)

3 byte Register Mnemonic field

12 byte data field; 10 bytes for number, one byte for sign, one byte for decimal point (The T command may be a different byte length)

<CR> carriage return

<LF> line feed

<SP>* (Space)

<CR>* carriage return

<LF>* line feed

* These characters only appear in the last line of a block print.

The first two characters transmitted are the node address, unless the node address assigned =0, in which case spaces are substituted. A space follows the node address field. The next three characters are the register ID (Serial

Mnemonic).

The numeric data is transmitted next. The numeric field is 12 characters long

(to accommodate the 10 digit totalizer), with the decimal point position floating within the data field. Negative value have a leading minus sign. The data field is right justified with leading spaces.

Register Identification Chart

ID Value Description

Register

Applicable Commands/Comments

A Input INP T, P

Total

Max Input

Min Input

Setpoint 1

Setpoint 2

Setpoint 3

TOT

MAX

MIN

SP1

SP2

SP3

T, P, R

T, P, V, R

(Reset command resets total to zero)

(Reset command resets MAX to current reading)

(Reset command resets MIN to current reading)

(Reset command resets the setpoint output)

T, V (Applies to manual mode)

H Setpoint 4

Analog Output

Control Status

SP4

AOR

CSR T, V

Command String Examples:

1. Node address = 17, Write 350 to Setpoint 1, response delay of 2 msec min

String: N17VE350$

2. Node address = 5, Read Input value, response delay of 50 msec min

String: N5TA*

3. Node address = 0, Reset Setpoint 4 output, response delay of 50 msec min

String: RH*

Sending Numeric Data

Numeric data sent to the meter must be limited to 5 digits (-19,999 to

99,999). If more than 5 digits are sent, the meter accepts the last 5. Leading zeros are ignored. Negative numbers must have a minus sign. The meter ignores any decimal point and conforms the number to the scaled resolution. (For example: the meter’s scaled decimal point position = 0.0 and 25 is written to a register. The value of the register is now 2.5 In this case, write a value = 25.0).

Note: Since the meter does not issue a reply to value change commands, follow with a transmit value command for readback verification.

The end of the response string is terminated with a carriage return <CR> and

<LF>. When block print is finished, an extra <SP><CR> <LF> is used to provide separation between the blocks.

Abbreviated Transmission

Byte Description

1-12

12 byte data field, 10 bytes for number, one byte for sign, one byte for decimal point

13 <CR> carriage return

14 <LF> line feed

15 <SP>* (Space)

16 <CR>* carriage return

17 <LF>* line feed

* These characters only appear in the last line of a block print.

The abbreviated response suppresses the node address and register ID, leaving only the numeric part of the response.

Meter Response Examples:

1. Node address = 17, full field response, Input = 875

17 INP 875 <CR><LF>

2. Node address = 0, full field response, Setpoint 2 = -250.5

SP2 -250.5<CR><LF>

3. Node address = 0, abbreviated response, Setpoint 2 = 250, last line of block print

250<CR><LF><SP><CR><LF>

SERIAL COMMANDS FOR PAX SOFTWARE

(CSR) Control Status Register

The Control Status Register is used to both directly control the meter’s outputs (setpoints and analog output), and interrogate the state of the setpoint outputs. The register is bit mapped with each bit position within the register assigned to a particular control function. The control function are invoked by writing to each bit position. The bit position definitions are: bit 0: Setpoint 1 Output Status

0 = output off

1 = output on bit 1: Setpoint 2 Output Status

0 = output off

1 = output on bit 2: Setpoint 3 Output Status

0 = output off

1 = output on bit 3: Setpoint 4 Output Status

0 = output off

1 = output on bit 4: Manual Mode

0 = automatic mode

1 = manual mode bit 5: Always stays 0, even if 1 is sent.

bit 6: Sensor Status (PAXT only)

0 = sensor normal

1 = sensor fail bit 7: Always stays 0, even if 1 is sent.

Although the register is bit mapped starting with bit 7, HEX < > characters are sent in the command string. Bits 7 and 5 always stay a zero, even if a “1” is sent. This allows ASCII characters to be used with terminals that may not have extended character capabilities.

Writing a “1” to bit 4 of CSR selects manual mode. In this mode, the setpoint outputs are defined by the values written to the bits b0, b1, b2, b3; and the analog output is defined by the value written to the AOR. Internal control of these outputs is then overridden.

In automatic mode, the setpoint outputs can only be reset off. Writing to the setpoint output bits of the CSR has the same effect as a Reset command (R).

The contents of the CSR may be read to interrogate the state of the setpoint outputs and to check the status of the temperature sensor (PAXT only).

Examples:

1. Set manual mode, turn all setpoints off:

VJ<30>* or VJ0*

7 6 5 4 3 2 1 0:bit location

ASCII 0 = 0 0 1 1 0 0 0 0 or <30>

V is command write, J is CSR and * is terminator.

2. Turn SP1, SP3 outputs on and SP2, SP4 outputs off:

VJ<35>* or VJ5*

ASCII 5 = 0

0:bit location

1 or <35>

3. Select Automatic mode:

VJ<40>* or VJ@*

ASCII @ = 0

0:bit location

0 or <40>

Note: Avoid writing values <0A> (LF), <0D> (CR), <24> ($) and <2E> (*) to the CSR. These values are interpreted by the meter as end of command control codes and will prematurely end the write operation.

(AOR) Analog Output Register

The Analog Output Register controls the analog output of the meter. The manual mode must first be engaged by setting bit 4 of the Control Status

0 mA, 0 V and 20 mA, 10 V; respectively. The table lists correspondence of the output signal with the register value.

Register Value

2047

4094

4095

Output Signal*

I (mA) V (V)

0.000

0.005

0.000

0.0025

10.000

19.995

20.000

5.000

9.9975

10.000

*Due to the absolute accuracy rating and resolution of the output card, the actual output signal may differ 0.15% FS from the table values. The output signal corresponds to the range selected

(20 mA or 10 V).

Writing to this register while the meter is in the manual mode causes the output signal to update immediately. While in the automatic mode, this register may be written to, but the output will not update until the meter is placed in manual mode.

Examples:

1. Set output to full scale:

VI4095*

2. Set output to zero scale:

VI0*

Command Response Time

The meter can only receive data or transmit data at any one time (half-duplex operation). The meter ignores commands while transmitting data, but instead uses RXD as a busy signal. When sending commands and data to the meter, a delay must be imposed before sending another command. This allows enough time for the meter to process the command and prepare for the next command.

Timing Diagram Figure

At the start of the time interval t

, the computer program prints or writes the string to the com port, thus initiating a transmission. During t

, the command characters are under transmission and at the end of this period, the command terminating character (*) is received by the meter. The time duration of t

1 dependent on the number of characters and baud rate of the channel.

is t

= (10 * # of characters) / baud rate

At the start of time interval t

, the meter starts the interpretation of the command and when complete, performs the command function. This time interval t

2 varies from 2 msec to 50 msec. If no response from the meter is expected, the meter is ready to accept another command.

If the meter is to reply with data, the time interval t

2 is controlled by the use of the command terminating character. The standard command line terminating character is ‘*’. This terminating character results in a response time window of

50 msec minimum and 100 msec maximum. This allows sufficient time for the release of the sending driver on the RS485 bus. Terminating the command line with ‘$’ results in a response time window (t

) of 2 msec minimum and 50 msec maximum. The faster response time of this terminating character requires that sending drivers release within 2 msec after the terminating character is received.

At the beginning of time interval t

, the meter responds with the first character of the reply. As with t

, the time duration of t number of characters and baud rate of the channel. t

3 is dependent on the

= (10 * # of characters) / baud rate. At the end of t

, the meter is ready to receive the next command.

The maximum serial throughput of the meter is limited to the sum of the times t

, t

2 and t

Communication Format

Data is transferred from the meter through a serial communication channel.

In serial communications, the voltage is switched between a high and low level at a predetermined rate (baud rate) using ASCII encoding. The receiving device reads the voltage levels at the same intervals and then translates the switched levels back to a character.

The voltage level conventions depend on the interface standard. The table lists the voltage levels for each standard.

LOGIC INTERFACE STATE RS232*

0 mark (idle) space (active)

* Voltage levels at the Receiver

TXD,RXD; -3 to -15 V

TXD,RXD; +3 to +15 V

RS485* a-b < -200 mV a-b > +200 mV

Data is transmitted one byte at a time with a variable idle period between characters (0 to

∞

). Each ASCII character is “framed” with a beginning start bit, an optional error detection parity bit and one or more ending stop bits. The data format and baud rate must match that of other equipment in order for communication to take place. The figures list the data formats employed by the meter.

Start bit and Data bits

Data transmission always begins with the start bit. The start bit signals the receiving device to prepare for reception of data. One bit period later, the least significant bit of the ASCII encoded character is transmitted, followed by the remaining data bits. The receiving device then reads each bit position as they are transmitted. Since the sending and receiving devices operate at the same transmission speed (baud rate), the data is read without timing errors.

Character Frame Figure

Parity bit

After the data bits, the parity bit is sent. The transmitter sets the parity bit to a zero or a one, so that the total number of ones contained in the transmission

(including the parity bit) is either even or odd. This bit is used by the receiver to detect errors that may occur to an odd number of bits in the transmission.

However, a single parity bit cannot detect errors that may occur to an even number of bits. Given this limitation, the parity bit is often ignored by the receiving device. The PAX meter ignores the parity bit of incoming data and sets the parity bit to odd, even or none (mark parity) for outgoing data.

Stop bit

The last character transmitted is the stop bit. The stop bit provides a single bit period pause to allow the receiver to prepare to re-synchronize to the start of a new transmission (start bit of next byte). The receiver then continuously looks for the occurrence of the start bit.

This page intentionally left blank

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship for a period limited to one year from the date of shipment, provided the products have been stored, handled, installed, and used under proper conditions. The Company’s liability under this limited warranty shall extend only to the repair or replacement of a defective product, at The Company’s option. The Company disclaims all liability for any affirmation, promise or representation with respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims, and expenses arising out of subsequent sales of RLC products or products containing components manufactured by RLC and based upon personal injuries, deaths, property damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be to any extent liable, including without limitation penalties imposed by the Consumer Product Safety

Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty

Act (P.L. 93-637), as now in effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except those expressly contained herein. The Customer acknowledges the disclaimers and limitations contained herein and relies on no other warranties or affirmations.

Red Lion Controls

20 Willow Springs Circle

York PA 17402

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls BV

Basicweg 11b

NL - 3821 BR Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls AP

31, Kaki Bukit Road 3,

#06-04/05 TechLink

Singapore 417818

Tel +65 6744-6613

Fax +65 6743-3360

Živjo! Sem AI chatbot, posebej usposobljen za pomoč pri Red Lion Controls PAXCDC 10. Temeljito sem pregledal dokument in vam lahko pomagam najti točne informacije, ki jih potrebujete, ali razložim vsebino na jasen in preprost način. Ne glede na to, ali iščete navodila o določenih funkcijah, korake za odpravljanje težav ali splošno uporabo, lahko zastavite svoja vprašanja. Več podrobnosti kot navedete o svojih pomislekih ali potrebah, natančneje in učinkoviteje vam lahko pomagam!

Pomočnik tipka

Pomočnik je prekinil povezavo. Poskusite znova pozneje.

Izgleda, da ste prišli do dokumenta, ki je napisan v več jezikih, vključno z jezikom, ki ni vaš materni jezik. Uporabite lahko naslednje povezave, da začasno skrijete strani brez jezika, ki ga želite.