Citroën C3 01/05/2014 - 28/02/2015 Owner Manual
Advertisement
Advertisement
Handbook
On-line handbook
Referring to the handbook on-line also gives you access to the latest information available, easily identified by the bookmark, associated with this symbol:
Find your handbook on the CITRoËn
website, under "MyCITROËN".
This personal and customisable space allows you to establish direct and special contact with
CITRoËn.
Select one of the following means of access to view your handbook on-line...
If the "MyCITRoËn" function is not available on the CITRoËn
public website for your country, you can find your handbook at the following address: http://service.citroen.com/ddb/
Select: the language, the vehicle, its body style, the print edition of your handbook appropriate for the date of registration of your vehicle.
Scan this code for direct access to your handbook.
We draw your attention to the following...
Reading the detailed sections is essential to make the most of your vehicle, in complete safety.
Your vehicle is fitted with only some of the equipment described in this document, depending on the trim level, version and the specifications for the country in which it is sold.
The fitting of electrical equipment or accessories which are not recommended by CITRoËn may result in a failure of your vehicle's electronic system. Contact a CITRoËn dealer for information on the recommended equipment and accessories.
Key
safety warning additional information contributes to the protection of the environment refer to the page indicated
CITRoËn has a presence on every continent, a complete product range, bringing together technology and a permanent spirit of innovation, for a modern and creative approach to mobility.
We thank you and congratulate you on your choice.
At the wheel of your new vehicle, getting to know each system, each control, each setting, makes your trips, your journeys more comfortable and more enjoyable.
Happy motoring!
Contents
deactivating the passenger's front airbag 89
Contents
Tyre under-inflation detection
Overview
Exterior
Zenith windscreen
This large windscreen provides incomparable visibility and light in the passenger compartment.
Temporary puncture repair kit
This kit is a complete system consisting of a compressor and a sealant cartridge, for the temporary repair of a tyre.
4
Stop & Start
This system puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, etc...). The engine restarts as soon as you want to move off. The Stop & Start system reduces fuel consumption, exhaust emissions and the noise level when stationary.
Rear parking sensors / reversing camera
These systems detect and warn you of any obstacle located behind the vehicle.
Interior
Scented air freshener
The scented air freshener diffuses the selected fragrance throughout the passenger compartment from its location in the ventilation system.
Digital air conditioning
after setting the desired level of comfort, the system then automatically controls this level according to the ambient conditions.
Audio and communication systems
These systems benefit from the latest technology: MP3 compatible audio system,
USb port, bluetooth hands-free system, eMyWay with 16/9 colour screen, auxiliary inputs, Hi-Fi audio system.
eMyWay
Audio system
Overview
.
Interior mood lighting
This subdued passenger compartment lighting improves visibility inside the vehicle in low lighting conditions. It comprises several lamps, located in the automatic day/night mirror support and in the lower dashboard storage compartment.
Gear efficiency indicator
depending on the driving conditions and your style of driving, this system may suggest when to change up to reduce your fuel consumption.
5
6
Overview
Instruments and controls
1.
audio equipment steering mounted controls.
2.
Steering lock and ignition.
3.
Wipers / screenwash / trip computer control stalk.
4.
Instrument panel.
5.
Scented air freshener.
6.
driver's airbag.
Horn.
7.
Gear lever.
8.
Parking brake.
9.
Central armrest with storage.
10.
door mirror controls.
Electric window controls.
Rear doors and electric windows deactivation control.
11.
Storage compartment.
12.
Electric child lock button or alarm button.
Electronic stability programme button
(dSC/aSR).
Stop & Start deactivation button.
13.
Side adjustable air vent.
14.
Front door window demisting/defrosting vent.
15.
Speaker (tweeter).
16.
Windscreen demisting/defrosting vent.
Instruments and controls
1.
Steering wheel adjustment control.
2.
Headlamp height adjustment.
3.
Cruise control / speed limiter controls.
4.
Lighting and direction indicator control stalk.
5.
Microphone.
6.
Central locking button.
7.
Multifunction screen.
8.
Hazard warning lamps button.
9.
Central adjustable air vents.
10.
Sunshine sensor
Hi-Fi audio system central speaker.
11.
Passenger's airbag.
12.
Glove box / Passenger's airbag deactivation / Fusebox.
13.
bonnet release lever.
14.
12 V accessory socket
USb port / auxiliary socket.
15.
Upper and lower storage.
16.
audio system or eMyWay.
17.
Heating / air conditioning controls.
Overview
.
7
8
Eco-driving
Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO
2
emissions.
Optimise the use of your gearbox
With a manual gearbox, move off gently and change up without waiting. during acceleration change up early.
With an automatic or electronic gearbox, give preference to automatic mode and avoid pressing the accelerator pedal heavily or suddenly.
The gear shift indicator invites you engage the most suitable gear: as soon as the indication is displayed in the instrument panel, follow it straight away.
For vehicles fitted with an electronic or automatic gearbox, this indicator appears only in manual mode.
Control the use of your electrical equipment
Before moving off, if the passenger compartment is too warm, ventilate it by opening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air vents open.
Remember to make use of equipment that can help keep the temperature in the passenger compartment down (sunroof and window blinds...).
Switch off the air conditioning, unless it has automatic regulation, as soon as the desired temperature is attained.
Switch off the demisting and defrosting controls, if not automatic.
Switch off the heated seat as soon as possible.
Drive smoothly
Maintain a safe distance between vehicles, use engine braking rather than the brake pedal, and press the accelerator progressively. These practices contribute towards a reduction in fuel consumption and CO
2 emissions and also helps reduce the background traffic noise.
Switch off the headlamps and front foglamps when the level of light does not require their use.
Avoid running the engine before moving off, particularly in winter; your vehicle will warm up much faster while driving.
If your vehicle has cruise control, make use of the system at speeds above 25 mph (40 km/h) when the traffic is flowing well.
as a passenger, if you avoid connecting your multimedia devices
(film, music, video game...), you will contribute towards limiting the consumption of electrical energy, and so of fuel.
disconnect your portable devices before leaving the vehicle.
Eco-driving
.
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest items in the bottom of the boot, as close as possible to the rear seats.
Limit the loads carried in the vehicle and reduce wind resistance (roof bars, roof rack, bicycle carrier, trailer...). Use a roof box in preference.
Remove roof bars and roof racks after use.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when cold, referring to the label in the door aperture, driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the tyres on any trailer or caravan.
At the end of winter, remove snow tyres and refit your summer tyres.
Have your vehicle serviced regularly (engine oil, oil filter, air filter, passenger compartment filter...) and observe the schedule of operations recommended in the maintenance and warranty guide.
With a blueHdi diesel engine, if the SCR system is faulty your vehicle becomes polluting; go to a CITROËN dealer or a qualified workshop without delay to have the emissions of nitrous oxides brought back to the legal level.
When refuelling, do not continue after the third cut-off of the nozzle to avoid any overflow.
At the wheel of your new vehicle, it is only after the first 1 800 miles
(3 000 kilometres) that you will see the fuel consumption settle down to a consistent average.
9
Monitoring
Instrument panels with manual gearbox
Panel grouping together the vehicle operation indication dials and warning lamps.
Dials Screen
10
1.
Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2.
Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
3.
Fuel level.
Indicates the quantity of fuel remaining in the tank.
4.
Screen.
5.
Display management button
Servicing information.
adjust the time and choose units.
Reset the service indicator.
6.
Instrument panel lighting button.
adjusts the brightness of the lighting of the instruments and controls.
For more information, refer to the section on the button or function and its associated display.
A.
Ambient temperature.
(°Celsius or °Fahrenheit)
B.
Gear efficiency indicator.
C.
Time.
D.
Engine oil level indicator.
Appears a few seconds after switching on the ignition, then disappears.
E.
Trip computer.
F.
Service indicator.
(miles or km) then,
Total mileage.
These two functions are displayed successively when switching on the ignition.
Monitoring
Instrument panels for electronic or automatic gearboxes
Panel grouping together the vehicle operation indication dials and warning lamps. Depending on the version, the instrument panel may have permanent back-lighting.
Dials Screen
1
1.
Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2.
Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
3.
Fuel level.
Indicates the quantity of fuel remaining in the tank.
4.
Screen.
5.
Display management button
Alternates display between range and trip mileage recorder.
Servicing information.
Resets the selected function to zero (trip distance recorder or service indicator).
6.
Instrument panel lighting button.
adjusts the brightness of the lighting of the instruments and controls.
For more information, refer to the section on the button or function and its associated display.
A.
Speed limiter
(mph or km/h) or
Cruise control.
B.
Gear efficiency indicator.
C.
Electronic or automatic gearbox information.
D.
Range
(miles or km) or
Trip mileage recorder.
E.
Service indicator
(miles or km), then
Total mileage recorder.
These two functions are displayed successively when switching on the ignition
F.
Engine oil level indicator.
Appears a few seconds after switching on the ignition, then disappears.
11
12
Monitoring
Indicator and warning lamps
Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or of the occurrence of a fault
(warning lamp).
When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignition is switched on.
When the engine is started, these same warning lamps should go off.
If they remain on, before moving off, refer to the information on the warning lamp concerned.
Associated warnings
The illumination of certain warning lamps may be accompanied by an audible signal and a message in the multifunction screen.
The warning lamps may come on continuously
(fixed) or flash.
Certain warning lamps may come on in one of two different modes. Only by relating the type of illumination to the operating status of the vehicle can it be ascertained whether the situation is normal or whether a fault has occurred.
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.
Warning/indicator lamp is on
Left-hand direction indicator flashing with buzzer.
Cause
The lighting stalk is pushed down.
Action / Observations
Right-hand direction indicator flashing with buzzer.
Hazard warning lamps flashing with audible signal.
The lighting stalk is pushed up.
The hazard warning lamps switch, located on the dashboard, has been operated.
The left-hand and right-hand direction indicators and their associated indicator lamps flash simultaneously.
Sidelamps fixed.
The lighting stalk is in the
"Sidelamps" position.
Warning/indicator lamp is on
Dipped beam headlamps fixed.
Main beam headlamps fixed.
Front foglamps fixed.
Rear foglamps fixed.
Diesel engine pre-heating fixed.
Parking brake fixed.
Monitoring 1
Cause
The lighting stalk is in the "dipped beam headlamps" position.
The lighting stalk is pulled towards you.
The front foglamps are switched on using the ring on the lighting control stalk.
The rear foglamps are switched on.
Action / Observations
Pull the stalk to return to dipped beam headlamps.
Turn the ring on the lighting control stalk rearwards twice to switch off the front foglamps.
Turn the ring on the stalk rearwards to switch off the rear foglamps.
The key is at position 2 (ignition on) in the ignition switch.
Wait until the warning lamp goes off before starting.
The period of illumination of the warning lamp is determined by the climatic conditions (up to about thirty seconds in extreme climatic conditions).
If the engine does not start, switch the ignition off and then on, wait until the warning lamp goes off again, then start the engine.
The parking brake is applied or not properly released.
Release the parking brake to switch off the warning lamp, keeping your foot on the brake pedal.
observe the safety recommendations.
For more information on the parking brake, refer to the corresponding section.
13
14
Monitoring
Warning/indicator lamp
Engine coolant temperature
Stop & Start is on fixed blue fixed.
flashes for a few seconds, then goes off.
Cause on starting the engine, it indicates that the engine is cold.
Action / Observations
After a few minutes driving, it swiches off to indicate that the engine temperature is normal.
In order to protect your engine, avoid driving too hard until the warning lamp has switched off.
When the vehicle stops (red lights, traffic jams, ...) the Stop & Start system has put the engine into SToP mode.
The warning lamp goes off and the engine restarts automatically in START mode, as soon as you want to move off.
SToP mode is temporarily unavailable.
or
STaRT mode is invoked automatically.
For more information on special cases with STOP mode and STaRT mode, refer to the "Stop & Start" section.
Warning/indicator lamp is on
Foot on the brake pedal fixed.
flashing.
Automatic wiping fixed.
Cause
The brake pedal must be pressed.
Monitoring 1
Action / Observations
With an electronic gearbox, press the brake pedal to start the engine (lever in position N ).
With an automatic gearbox, with the engine running, press the brake pedal before releasing the parking brake, to unlock the lever and come out of position P .
If you wish to release the parking brake without pressing the brake pedal, this warning lamp will remain on.
With an electronic gearbox, if you hold the vehicle on an incline using the accelerator for too long, the clutch overheats.
The wiper control is pushed downwards.
Use the brake pedal and/or the parking brake.
Automatic front wiping is activated.
15
16
Monitoring
Deactivation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.
This is may be accompanied by an audible signal and a message on the multifunction screen.
Warning/indicator lamp is on
Passenger's airbag system fixed.
Cause Action / Observations
The control, located in the glove box, is set to the OFF position.
The passenger's front airbag is deactivated.
You can install a "rearward facing" child seat, unless there is a fault with the operation of the airbags (airbag warning lamp on).
Set the control to the ON position to activate the passenger's front airbag.
In this case, do not fit a child seat in the rearward facing position.
Dynamic stability control
(DSC/ASR) fixed.
The button, located at the bottom left of the dashboard, is pressed. Its indicator lamp is on.
The dSC/aSR is deactivated.
dSC: dynamic stability control.
aSR: anti-slip regulation.
Press the button to activate the dSC/aSR. Its indicator lamp goes off.
The DSC/ASR system is activated automatically when the vehicle is started.
If deactivated, the system is reactivated automatically from around 30 mph (50 km/h).
Warning lamps
When the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates a fault which requires action on the part of the driver.
Monitoring
Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the multifunction screen.
If you encounter any problems, do not hesitate to contact a CITROËN dealer or a qualified workshop.
Warning/indicator lamp is on
STOP
Service
Cause Action / Observations fixed, alone or associated with another warning lamp, accompanied by an audible signal and a message on the screen.
temporarily.
Illumination of the warning lamp is associated with a serious braking system or engine coolant temperature problem.
Stop as soon as it is safe to do so as the engine may cut out when driving.
Park, switch off the ignition and call a CITROËN dealer or a qualified workshop.
Minor problems have occurred for which there is no specific warning lamp.
Identify the problem by reading the message shown in the screen, such as, for example:
- the engine oil level,
-
the screenwash level,
- the remote control battery,
- saturation of the particle emission filter on diesel vehicles
(refer to the "Particle emissions filter (diesel)" section).
For any other faults, contact a CITRoËn dealer or a qualified workshop.
fixed.
Major problems have occurred for which there is no specific warning lamp.
Identify the problem by reading the message shown in the screen and contact a CITRoËn dealer or a qualified workshop.
1
17
18
Monitoring
Warning/indicator lamp is on
Braking fixed, associated with the STOP warning lamp.
Cause
The braking system fluid level is too low.
Action / Observations
You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by a
CITROËN dealer or a qualified workshop.
+
Anti-lock
Braking System
(ABS) fixed.
Electronic stability programme
(ESP/ASR)
Engine autodiagnosis system fixed, associated with the SToP and abS warning lamp.
The electronic brake force distribution
(EbFd) system has a fault.
You must stop as soon as it is safe to do so.
Have it checked by a CITRoËn dealer or a qualified workshop.
flashing.
fixed.
flashing.
fixed.
The anti-lock braking system has a fault.
The vehicle retains conventional braking.
drive carefully at reduced speed and contact a
CITROËN dealer or a qualified workshop without delay.
The ESP/aSR regulation is operating.
The system optimises traction and improves the directional stability of the vehicle.
Unless it has been deactivated
(button pressed and its indicator lamp on) the ESP/aSR system has a fault.
Have it checked by a CITRoËn or a qualified workshop.
The engine management system has a fault.
The emission control system has a fault.
Risk of destruction of the catalytic converter.
Have it checked by a CITRoËn dealer or a qualified workshop.
The warning lamp should go off when the engine is started.
If it does not go off, contact a CITRoËn dealer or qualified workshop without delay.
Warning/indicator lamp is on
Low fuel level fixed.
Maximum coolant temperature fixed.
Engine oil pressure fixed.
Battery charge fixed.
Monitoring 1
Cause Action / Observations
When it first comes on there remains approximately 5 litres of fuel in the tank.
You must refuel as soon as possible to avoid running out of fuel.
This warning lamp will come on every time the ignition is switched on, until a sufficient addition of fuel is made.
Fuel tank capacity: approximately 50 litres (petrol),
46 litres (Diesel) or 37 litres (LPG); depending on version: approximately 30 litres (petrol or diesel).
never continue to drive until you run out of fuel as this could damage the emission control and injection systems.
The temperature of the cooling system is too high.
Stop as soon as it is safe to do so.
Wait until the engine has cooled down before topping up the level, if necessary.
If the problem persists, contact a CITRoËn dealer or qualified workshop.
There is a fault with the engine lubrication system.
You must stop as soon it is safe to do so.
Park, switch off the ignition and contact a CITROËN dealer or a qualified workshop.
The battery charging circuit has a fault (dirty or loose terminals, slack or cut alternator belt, ...).
The warning lamp should go off when the engine is started.
If it does not go off, contact a CITRoËn dealer or a qualified workshop.
19
20
Monitoring
Warning/indicator lamp is on
Door(s) open fixed if the speed is below 6 mph (10 km/h).
Cause a door or the boot is still open.
Airbags fixed and accompanied by an audible signal if the speed is above
6 mph (10 km/h).
temporarily.
fixed.
This lamp comes on for a few seconds when you turn on the ignition, then goes off.
one of the airbag or seat belt pretensioner systems has a fault.
Action / Observations
Close the door or boot.
This lamp should go off when the engine is started.
If it does not go off, contact a CITRoËn dealer or a qualified workshop.
Have it checked by a CITRoËn dealer or a qualified workshop.
Seat belt not fastened / unfastened
Power steering fixed then flashing accompanied by an increasing audible signal.
fixed.
The driver and/or the front passenger has not fastened or has unfastened their seat belt.
Pull the strap then insert the tongue in the buckle.
The power steering has a fault.
drive carefully at reduced speed.
Have it checked by a CITRoËn dealer or a qualified workshop.
+
Monitoring 1
Warning/indicator
Particle emissions filter
(Diesel) lamp
Water in Diesel is on fixed.
Cause
The Diesel fuel filter contains water.
Action / Observations
Risk of damage to the injection system on diesel engines.
Contact a CITROËN dealer or a qualified workshop without delay.
fixed, accompanied by an audible signal.
This indicates that the particle emissions filter is starting to become saturated.
As soon as driving conditions allow, regenerate the filter by driving at a speed of at least 35 mph (60 km/h) until the warning lamp goes off (see the "Checks -
Particle emissions filter" section).
Under-inflation fixed, accompanied by an audible signal.
This indicates the low level of the additive reservoir.
fixed, accompanied by an audible signal and a message.
The pressure in one or more wheels is too low.
Have the reservoir topped up as soon as possible by a CITROËN dealer or a qualified workshop (see the
"Checks - additive level" section).
Check the pressure of the tyres as soon as possible.
This check should preferably be carried out when the tyres are cold.
You must reinitialise the system after the adjustment of one or more tyre pressures and after changing one or more wheels.
For more information, refer to the "Under-inflation detection" section.
flashing then fixed, accompanied by the
Service warning lamp.
The system has fault: the tyre pressures are no longer monitored.
Check the tyre pressures as soon as possible.
have the system checked by a CITRoËn dealer or a qualified workshop.
21
22
Monitoring
Service indicator
System which informs the driver when the next service is due, in accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator zero reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service.
Between 600 miles (1 000 km) and 1800 miles (3 000 km) remain before the next service is due
For a few seconds after the ignition is switched on, the spanner symbolising the service operations comes on. The distance recorder display line indicates the distance remaining before the next service is due.
Example:
1 700 miles (2 800 km) remain before the next service is due.
Less than 600 miles (1 000 km) remain before the next service is due
Example:
560 miles (900 km) remain before the next service is due.
For a few seconds after the ignition is switched on, the display indicates:
More than 1800 miles (3000 km) remain before the next service is due
When the ignition is switched on, no service information appears in the screen.
For a few seconds after the ignition is switched on, the screen indicates:
A few seconds after the ignition is switched on, the spanner goes off
; the distance recorder resumes its normal operation. The screen then indicates the total and trip distances.
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a service must be carried out soon.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible.
Example: the service is overdue by 180 miles
(300 km).
For a few seconds after the ignition is switched on, the display indicates:
Monitoring
Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account.
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded the period since the last service, indicated in the maintenance and warranty guide.
Service indicator zero reset
after each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:
F switch off the ignition,
F press and hold the trip distance recorder zero reset button,
F switch on the ignition; the distance recorder display begins a countdown,
F when the display indicates
"=0" , release the button; the spanner disappears.
Retrieving the service information
You can access the service information at any time.
F Press the trip distance recorder zero reset button.
The service information is displayed for a few seconds, then disappears.
1
23
Monitoring
Engine oil level indicator*
Oil level correct Oil level indicator fault
On vehicles fitted with an electric oil level indicator, information on the oil level is displayed in the instrument panel for a few seconds when the ignition is switched on, after the service information.
The level shown will only be correct if the vehicle is on level ground and the engine has been off for more than
30 minutes.
Oil level low
This is indicated by the flashing of "OIL" , accompanied by illumination of the service warning lamp, an audible signal and a message.
If the low oil level is confirmed by a check using the dipstick, the level must be topped up to prevent damage to the engine.
Refer to the "Checking levels" section.
This is signaled by the flashing of "OIL--" .
Contact a CITRoËn dealer or a qualified workshop.
In the event of a fault with the electric oil level indicator, the engine oil level is no longer monitored.
While the system is faulty, you should check the engine oil level using the manual dipstick located under the bonnet.
Refer to the "Checking levels" section.
24
* depending on version.
Monitoring
Distance recorders
The total and trip distances are displayed for thirty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.
Clock
When traveling abroad, you may have to change the units of distance: the display of road speed must be in the official units (miles or km) for the country. The change of units is done via the screen configuration menu, with the vehicle stationary.
Total distance recorder
It measures the total distance travelled by the vehicle since its first registration.
Trip distance recorder
It measures the distance travelled since it was reset to zero by the driver.
F With the ignition on, press the button until zeros appear.
Adjusting the time - Choice of units
To adjust the time of the clock and choose the units used by the screen, use the right-hand button on the instrument panel, carrying out the operations in the following order:
F press the button for more than two seconds: the minutes flash,
F press the button to increase the minutes,
F press the button for more than two seconds: the hours flash,
F press the button to increase the hours,
F press the button for more than two seconds:
24H or 12H is displayed,
F press the button to select 24H or 12H,
F press the button for more than two seconds:
°C or °F is displayed,
F press the button to select °C or °F,
F press the button for more than two seconds to complete the adjustments.
After approximately 30 seconds without any action, the screen returns to the normal display.
1
25
Monitoring
Lighting dimmer
System for manual adjustment of the brightness of the instruments and controls in relation to the exterior brightness.
Black panel
System allowing certain displays to be switched off for night driving.
26
Activation
When the lighting is on:
F press the button to change the brightness of the instruments and controls,
F when the level of brightness required is reached, release the button.
Deactivation
When the lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.
The instrument panel remains illuminated with only the vehicle speed and cruise control or speed limiter information, if in use.
If there is an alert or a change in a function or to a setting, the black panel mode is interrupted.
Activation
F With the lighting on, press the left hand button of the instrument panel several times to progressively reduce the dashboard lighting level.
F Press the button again to reduce the lighting to the minimum level and switch off the interior mood lighting.
F Press the button again to activate the black panel.
Trip computer
System that gives you information on the current journey (range, fuel consumption…).
- distance travelled,
Screen in the instrument panel
- average fuel consumption,
Information displays
F Press the button, located at the end of the wiper stalk , to display the various items of trip computer information in succession.
- average speed.
Monitoring 1
Monochrome screen A
The trip computer provides the following information:
- range,
F The next press then returns you to the normal display.
- current fuel consumption,
* Available only with the monochrome screen A.
- the Stop & Start time counter*,
Zero reset
F Press the control for more than two seconds to reset to zero the distance travelled, the average fuel consumption and the average speed.
27
28
Monitoring
Monochrome screen C
16/9 colour screen
(eMyWay)
- the current information tab with:
● the range,
● the current fuel consumption,
● the distance remaining to be travelled or the Stop &
Start time counter.
- the trip "1"
tab with:
● the distance travelled,
● the average fuel consumption,
● the average speed,
for the first trip.
- the trip "2"
tab with:
● the distance travelled,
● the average fuel consumption,
● the average speed,
for the second trip.
Trip zero reset
F When the trip required is displayed, press the button on the end of the wiper stalk for more than two seconds.
Trips "1" and "2" are independent but their use is identical.
For example, trip "1" can be used for daily figures, and trip "2" for monthly figures.
Information displays
F Press the button, located at the end of the wiper stalk , to display the various trip computer tabs in succession:
F Pressing the button again returns you to the normal display.
Trip computer, a few definitions
Range
(miles or km)
The distance which can still be travelled with the fuel remaining in the tank (related to the average fuel consumption over the last few miles (kilometres) travelled).
Current fuel consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.
This function is only displayed from
20 mph (30 km/h).
This value may vary following a change in the style of driving or the relief, resulting in a significant change in the current fuel consumption.
When the range falls below 20 miles (30 km), dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is displayed when it exceeds 60 miles (100 km).
Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip computer reset.
If dashes are displayed continuously while driving in place of the digits, contact a CITRoËn dealer or a qualified workshop.
Average speed
(mph or km/h)
Calculated since the last trip computer reset.
Monitoring 1
Distance travelled
(miles or km)
Calculated since the last trip computer reset.
Distance remaining to destination
(miles or km)
This is the distance remaining to be travelled to the final destination. It can be entered by the user.
If the distance is not entered, dashes are displayed in place of the digits.
Stop & Start time counter
(minutes / seconds or hours / minutes)
If your vehicle is fitted with Stop &
Start, a time counter calculates the time spent in SToP mode during a journey.
It resets to zero every time the ignition is switched on with the key.
29
Multifunction screens
Monochrome screen a
Displays in the screen Controls Main menu
30
This displays the following information:
- time,
- date,
- ambient temperature (this flashes if there is a risk of ice),
- status of the doors and boot,
- audio sources (radio, Cd...),
- trip computer (refer to the "Instruments and controls" section).
Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.:
"boot open") may appear temporarily. These can be cleared by pressing the "Back" button.
From the control panel of your audio system, you can:
F press the "MENU" button to gain access to the main menu ,
F press the " 5 " or " 6 " buttons to scroll through the items in the screen,
F press the "MODE" button to change the permanent application (date, audio source...),
F press the " 7 " or " 8 " buttons to change a setting value,
F press the "OK" button to confirm, or
F press the "Back" button to abandon the operation in progress.
F Press the "MENU" button to gain access to the main menu , then press the " 5 " or " 6 " buttons to scroll through the various menus:
- radio-Cd,
- vehicle configuration,
- options,
- display settings,
- languages,
- units.
F Press the "OK" button to select the menu required.
Radio-CD
With the Audio system switched on, once the
"Radio-Cd" menu has been selected you can activate or deactivate the functions linked with use of the radio (RDS, REG), or the CD
(introscan, shuffle, Cd repeat).
For more information on the "Radio-Cd" application, refer to the "audio system" section.
Multifunction screens
Vehicle configuration
Display settings
once the "display settings" menu has been selected, you can gain access to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Setting the date and time
F Press the MENU button.
F Select "display settings" using the " 5 " or " 6 " button.
F Press to confirm the selection.
F Select the "Year" function using the " 5 " or " 6 " button.
F Press to confirm the selection.
F Choose the desired value, using the " 7 " or " 8 " button.
F Press to confirm the selection.
F Repeat the procedure to set the "Month",
"day", "Hours", and "Minutes".
F once you have selected a setting, press the " 7 " or " 8 " buttons to change its value.
once the "Vehicle Configuration" menu has been selected, you can activate or deactivate the following equipment:
- wiper linked with reverse gear (refer to the
"Visibility"),
- guide-me-home lighting (refer to the
"Visibility"),
- parking sensors (refer to the "driving" section).
Using this menu, you can also reinitialise the tyre under-inflation detection system (see the
"Safety" section).
Options
once the "options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
F Press the " 5 " or " 6 " buttons to switch respectively to the previous or next setting.
F Press the "OK" button to save the change and return to the normal display or press the "Back" button to cancel.
2
31
32
Multifunction screens
Languages
once the "Languages" menu has been selected, you can change the language used by the display, by choosing a new language from the list offered.
Units
once the "Units" menu has been selected, you can change the units of the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or km/l).
once the fuel consumption units have been set to mpg, the information in the instrument panel screen on speed and distance will also be in mph and miles.
For safety reasons, configuration by the driver of the multifunction screen must only be done when stationary.
Monochrome screen C
Displays in the screen Controls Main menu
Multifunction screens
2
This displays the following information:
- time,
- date,
- ambient temperature (this flashes if there is a risk of ice),
- status of doors and boot,
- audio sources (radio, Cd, USb port / auxiliary socket etc.),
- trip computer (refer to the "Instruments and controls" section).
Warning messages (E.g. "Emissions control system faulty") or information messages
(E.g.: automatic headlamps active") may appear temporarily. These can be cleared by pressing the "Back" button.
From your audio system control panel, you can:
F press the "MENU" button to gain access to the main menu ,
F press the " 5 " or " 6 " buttons to scroll through the items in the screen,
F press the "MODE" button to change the permanent application (trip computer, audio source...),
F press the " 7 " or " 8 " buttons to change a setting value,
F press the "OK" button to confirm, or
F press the "Back" button to abandon the operation in progress.
F Press the "MENU" button to gain access to the main menu :
- audio functions,
- the trip computer,
- personalisation-configuration,
- telephone (hands-free kit).
F Press the " 5 " or " 6 " buttons to select the menu required, then confirm by pressing the "OK" button.
"Audio functions" menu
With the Audio system switched on, once this menu has been selected you can activate or deactivate the functions linked with use of the radio (RdS, REG, RadioText), the Cd
(introscan, shuffle, Cd repeat) or the MP3 player (USb port / auxiliary socket).
For more information on the "audio functions" application, refer to the "audio system" section.
33
Multifunction screens
34
"Trip computer" menu Status of functions
This summarises the status (active or inactive) of the vehicle's functions.
once this menu has been selected, you can consult information concerning the status of the vehicle (warnings log, status of functions, etc.)
Alert log
This summarises the active warning messages, displaying them in succession in the multifunction screen.
Enter distance to destination
This allows you to enter an approximate distance until your final destination.
F Press the "MENU" button to gain access to the general menu.
F Press the arrows, then the
"OK" button to select the "Trip computer" menu.
F In the "Trip computer" menu, select one of the following applications:
"Personalisation-
Configuration" menu
once this menu has been selected, you can gain access to the following functions:
- define the vehicle parameters,
- display configuration,
- choice of language.
Example: setting of the duration of the guideme-home lighting
F Press the " 5 " or " 6 " buttons, then the "OK" button to select the menu required.
Define the vehicle parameters
once this menu has been selected, you can activate or deactivate the following equipment:
- wiper linked to reverse gear (refer to the
"Visibility"),
- guide-me-home lighting and duration (see
"Visibility"),
- parking sensors (refer to the "driving" section).
Using this menu, you can also reinitialise the tyre under-inflation detection system (see the
"Safety") section.
F Press the " 5 " or " 6 " buttons, then the "OK" button to select the "Guide-mehome headlamps" line.
F Press the " 7 " or " 8 " buttons to set the value required (15, 30 or 60 seconds), then press the "OK" button to confirm.
Multifunction screens
2
F Press the " 5 " or " 6 " buttons, then the "OK" button to select the "OK" box and confirm or press the "Back" button to cancel.
35
36
Multifunction screens
"Telephone" Menu
Display configuration
once this menu has been selected, you can gain access to the following settings:
- brightness-video setting,
- date and time setting,
- selection of units.
once the fuel consumption units have been changed to mpg, the information in the screen relating to speed and distance also changes to mph and miles respectively.
Choice of language
once this menu has been selected, you can change the language used by the display, by choosing a new language from the list offered.
With audio system on, once this menu is selected you can configure your bluetooth hands-free system (pairing), view the various telephone directories (list of calls, services...) and manage your calls (call, hang up, second call, secret mode...).
For more information on the "Telephone" function, refer to the "audio system" section.
Setting the date and time
F Select the " Set date and time " function using the " 5 " or " 6 " button.
F Press to confirm the selection.
F adjust the settings one by one using the " 7 " or " 8 " button then confirm with
"OK" .
F Then select the "OK" box in the screen and confirm.
For safety reasons, configuration by the driver of the multifunction screen must only be done when stationary.
16/9 colour screen (eMyWay)
Displays in the screen Controls "SETUP" menu
Multifunction screens
2
It displays the following information automatically and directly:
- time,
- date,
- altitude,
- ambient temperature (the value displayed flashes if there is a risk of ice),
- check of the doors,
- parking sensor information,
- warning and vehicle function status messages, displayed temporarily,
- audio functions,
- trip computer information (see the
"Instrument s and controls" section),
- satellite navigation system information.
- the settings menus for the display screen, navigation system and vehicle systems.
To select one of the applications, from the eMyWay control panel:
F press the dedicated "RADIO" , "MUSIC" ,
"NAV" , "TRAFFIC" , "SETUP" or
"PHONE" button for access to the corresponding menu,
F turn the knob to change the selection,
F press the knob to confirm the selection,
or
F press the "Back" button to abandon the current operation and return to the previous display.
For more information on these applications, refer to the "eMyWay" section or to the specific user guide given to you with the other owner's documents.
F Press the "SETUP" button to gain access to the configuration menu. This allows you to select from the following functions:
- " Display configuration ",
- " Voice synthesis ",
- " Language ",
- " Vehicle parameters ",
- " Trip computer ",
37
38
Multifunction screens
Display configuration
This menu allows you to choose a colour scheme for the screen, adjust the brightness, date and time and choose the units for distance
(km or miles), fuel consumption (l/100 km, mpg or km/l) and temperature (°Celsius or
°Fahrenheit).
Date and time
F Press .
F Select the " Display configuration " and press the knob to confirm.
F Select " Adjust date and time " and press the knob to confirm.
F adjust the settings in turn using the directional arrows then confirm by pressing the knob.
Select " Synchronise minutes with GPS " so that the minutes are adjusted automatically by satellite reception.
Adjustment of voice synthesis
This menu allows you to adjust the volume for navigation instructions and choose the type of voice (male or female).
Language
This menu allows you to choose the language used by the display from a defined list.
Vehicle parameters
This menu allows you to activate or deactivate certain driving and comfort systems, arranged by category:
- " Parking sensors "
- " Rear wiper operation "
● "
Rear wiper in reverse: O
" (Rear wiper coupled to reverse)
Refer to the corresponding section.
- " Lighting configuration "
● "
Duration of guide-me-home lighting: O " (automatic guide-me-home lighting)
Refer to the corresponding section.
- " Driving assistance "
● "
Initialisation of under-inflation "
(Reinitialisation of the tyre underinflation detection system)
Refer to the corresponding section.
Trip computer
This menu allows you to see information on the state of the vehicle. You can choose between the following functions:
- "alert log".
List of active alerts.
- "State of functions"
List of the state of functions (activated, deactivated or faulty).
For safety reasons, configuration of the multifunction screen by the driver must only be done when stationary.
Comfort
Ventilation
Air intake
The air circulating in the passenger compartment is filtered and originates either from the outside via the grille located at the base of the windscreen or from the inside in air recirculation mode.
Air treatment
The incoming air follows various routes depending on the controls selected by the driver:
- direct arrival in the passenger compartment (air intake),
- passage through a heating circuit (heating),
- passage through a cooling circuit (air conditioning).
The temperature control enables you to obtain the level of comfort required by mixing the air of the various circuits.
The air distribution control enables you to diffuse the air in the passenger compartment combining several air vents.
The air flow control enables you to increase or reduce the speed of the ventilation blower.
Control panel
The controls of this system are grouped together on control panel A on the centre console. depending on the model, the functions offered are:
- the level of comfort required,
- air flow,
- air distribution,
- demisting-defrosting,
- manual or digital air conditioning controls.
Air distribution
1.
Windscreen demisting-defrosting vents.
2.
Front side window demisting-defrosting vents.
3.
Side adjustable air vents.
4.
Central adjustable air vents.
5.
Air outlets to the front footwells.
6.
Air outlets to the rear footwells.
3
39
40
Comfort
Recommendations for ventilation and air conditioning
In order for these systems to be fully effective, follow the operation and maintenance guidelines below:
F To obtain an even air distribution, take care not to obstruct the exterior air intake grilles located at the base of the windscreen, the nozzles, the vents and the air outlets, as well as the air extractor located in the boot.
F Do not cover the sunshine sensor, located on the dashboard; this is used for regulation of the air conditioning system.
F Operate the air conditioning system for at least 5 to 10 minutes, once or twice a month to keep it in perfect working order.
F Ensure that the passenger compartment filter is in good condition and have the filter elements replaced regularly.
We recommend the use of a combined passenger compartment filter. Thanks to its special active additive, it contributes to the purification of the air breathed by the occupants and the cleanliness of the passenger compartment (reduction of allergic symptoms, bad odours and greasy deposits).
F To ensure correct operation of the air conditioning system, you are also advised to have it checked regularly as recommended in the maintenance and warranty guide.
F If the system does not produce cold air, switch it off and contact a CITROËN dealer or a qualified workshop.
When towing the maximum load on a steep gradient in high temperatures, switching off the air conditioning increases the available engine power and so improves the towing ability.
If after an extended stop in sunshine, the interior temperature is very high, first ventilate the passenger compartment for a few moments.
Put the air flow control at a setting high enough to quickly change the air in the passenger compartment.
The air conditioning system does not contain chlorine and does not present any danger to the ozone layer.
The condensation created by the air conditioning results in a discharge of water under the vehicle which is perfectly normal.
Heating / Ventilation Manual air conditioning
Manual control panel Manual control panel
Electric control panel Electric control panel
Comfort
The heating / ventilation or air conditioning systems operates with the engine running, as well as in STOP mode with Stop & Start.
1. Temperature adjustment
F Turn the dial from blue
(cold) to red (hot) to adjust the temperature to your requirements.
2. Air flow adjustment
F Turn the dial from position 1 to position 5 to obtain a comfortable air flow.
3
F If you place the air flow control in position 0 (deactivation of the system), the temperature is no longer maintained at a comfortable level. However, a slight flow of air, due to the movement of the vehicle, can still be felt.
41
Comfort
42
3. Air distribution adjustment
Windscreen and side windows.
Windscreen, side windows and footwells.
Footwells.
Central and side vents.
The air distribution can be adapted by placing the dial in an intermediate position.
4. Air intake / Air recirculation 5. Air conditioning On / Off
The intake of exterior air avoids the formation of mist on the windscreen and side windows.
The recirculation of interior air insulates the passenger compartment from exterior odours and smoke.
Return to exterior air intake as soon as possible to prevent deterioration of the air quality and the formation of mist.
Manual control panel
F Move the manual control to the left to be in the
"recycling interior air" position.
F Move the manual control to the right to return to the
"fresh air intake" position.
The air conditioning is designed to operate effectively in all seasons, with the windows closed.
It enables you to:
- lower the temperature, in summer,
- increase the effectiveness of the demisting in winter, above 3 °C.
Switching on
F Press the "A/C" button, the button's indicator lamp comes on.
The air conditioning does not operate when the air flow adjustment control
2 is in position "0" .
To obtain cooled air more quickly, you can use recirculation of interior air for a few moments. Then return to fresh air intake.
Electric control panel
F Press the button to recirculate the interior air. The indicator lamp comes on to confirm this.
F Press the button again to allow fresh air into the passenger compartment. The indicator lamp goes off to confirm this.
Switching off
F Press the "A/C" button again, the button's indicator lamp goes off.
Switching off may affect comfort levels
(humidity, condensation).
Front demist - defrost
These markings on the control panel indicate the control positions for rapid demisting or defrosting of the windscreen and side windows.
With the heating / ventilation system
F Put the temperature and air flow controls to the dedicated marked position.
F Put the air intake control to the "Exterior air intake" position
(manual control to the right or electric control with indicator lamp off).
F Put the air distribution control to the
"Windscreen" position.
With the manual air conditioning system
F Put the temperature and air flow controls to the dedicated marked position.
F Put the air intake control to the "Exterior air intake" position
(manual control to the right or electric control with indicator lamp off).
F Put the air distribution control to the
"Windscreen" position.
F Switch on the air conditioning by pressing the "A/C"
button; the associated green warning lamp comes on.
With Stop & Start, when the demisting, air conditioning and air flow functions are activated, SToP mode is not available.
Comfort
3
43
44
Comfort
digital air conditioning
The air conditioning operates when the engine is running, as well as in STOP mode with Stop & Start.
Automatic operation
1. Automatic "comfort" programme
Press the "AUTO" button.
The "AUTO" symbol is displayed.
We recommend that you use this mode.
It provides optimised automatic control of all of the following functions: passenger compartment temperature, air flow, air distribution and air intake, in accordance with the comfort value that you have chosen.
This system is designed to operate effectively in all seasons, with the windows closed.
For your comfort, when the engine is switched off, the settings are retained until the engine is switched on again.
To prevent too great a distribution of cold air when the engine is cold, the air flow will only reach its optimum level gradually.
2. Temperature adjustment
The value indicated on the display corresponds to a level of comfort and not to a temperature in degrees Celsius or Fahrenheit.
Press the " 5 " and " 6 " buttons to change this value. a setting around the value 21 enables optimum comfort to be obtained. However, depending on your requirements, a setting between 18 and 24 is usual.
on entering the vehicle, if the interior is very cold or hot, there is no need to change the value displayed in order to reach the required level of comfort.
The system corrects the temperature difference automatically and as quickly as possible.
3. Automatic "visibility" programme
The automatic comfort programme may not be sufficient for rapid demisting or defrosting of the windscreen and side windows (humidity, several passengers, ice, etc.).
In this case, select the automatic visibility programme. The button 3 indicator lamp comes on.
The system automatically controls the air conditioning and the flow of air and provides optimum air distribution to the windscreen and side windows. It deactivates air recirculation
5 .
To exit this programme, press button 3 again or
"AUTO" , the indicator lamp on the button goes off and "AUTO" is displayed.
Manual override
It is possible to adjust one or more functions manually while leaving the other functions in automatic mode.
The "AUTO"
symbol switches off.
To return to automatic mode, press the
"AUTO" button.
Switching to manual mode may not be suitable (temperature, humidity, odour, condensation) and does not provide optimum comfort.
Comfort
For maximum cooling or heating of the cabin, it is possible to go beyond the minimum 14 or maximum 28 values.
F Press the blue button 2 until "LO" is displayed or the red button 2 until "HI" is displayed.
Press this button again or press the "AUTO" button to resume automatic management of the intake of air. The air recirculation symbol 5 goes off.
avoid prolonged recirculation of interior air (risk of condensation or deterioration of the air quality).
7. Air flow adjustment
Press the "full fan" button to increase the air flow.
The air flow symbol, the fan, fills progressively according to the value requested.
Press the "empty fan" button to decrease the air flow.
4. Air conditioning on/off
Press this button to switch off the air conditioning.
Stopping the air conditioning may cause some problems (humidity, misting).
automatic operation of the air conditioning is resumed when the button is pressed again.
The symbol "A/C" is displayed.
5. Air intake / Air recirculation
Press this button for recirculation of the interior air. The air recirculation symbol 5 is displayed.
air recirculation enables the passenger compartment to be isolated from exterior odours and smoke.
6. Air distribution adjustment
Pressing this button several times in succession enables the air flow to be directed in turn towards:
- the windscreen and the side windows
(demisting or defrosting),
- the windscreen, side windows and air vents,
- the windscreen, the side windows, the air vents and the footwells,
- the windscreen, the side windows and the footwells,
- the footwells,
- the air vents and the footwells,
- the air vents.
Switching the system off
Press the air flow
"empty fan" button 7 until the fan symbol disappears.
This action switches off all of the functions of the air conditioning system.
Thermal comfort is no longer controlled.
A slight flow of air resulting from the movement of the vehicle, remains perceptible however.
Pressing the air flow
"full fan" button 7 or on
"AUTO"
reactivates the system with the values set before it was switched off.
Avoid driving for long periods with the air conditioning switched off (risk of misting and reduction of the air quality in the cabin).
3
45
46
Comfort
Rear screen demist - defrost
The control button is located on the heating or air conditioning system control panel.
Switching on
The rear screen demisting/defrosting can only operate when the engine is running.
F Press this button to demist/defrost the rear screen and (depending on version) the door mirrors. The indicator lamp associated with the button comes on.
Switching off
The demisting/defrosting switches off automatically to prevent an excessive consumption of current.
F It is possible to stop the demisting/ defrosting operation before it is switched off automatically by pressing the button again. The indicator lamp associated with the button switches off.
With Stop & Start, when demisting has been activated, the SToP mode is not available.
If the engine is switched off before the demisting/defrosting is switched off automatically, demisting/defrosting will resume next time the engine is switched on.
F Switch off the demisting/defrosting of the rear screen and door mirrors as soon as appropriate as lower current consumption results in reduced fuel consumption.
Comfort
Scented air freshener
System permitting the diffusion of a fragrance in the passenger compartment in accordance with your requirements, by means of the adjustment dial and the various fragrance cartridges available.
Adjustment dial Fragrance cartridge
This cartridge can be removed easily. The first time it is used, replace the plug with a real cartridge.
You can change it at any time and store it in the sealed case which keeps it closed once it has been opened.
You can obtain different fragrance cartridges from a CITRoËn dealer or a qualified workshop.
This dial is located on the dashboard.
It allows you to adjust the intensity of diffusion of the fragrance.
F Turn the dial to the right to permit diffusion of the fragrance.
F Turn the dial to the left to stop diffusion of the fragrance.
Leave the central vents open.
do not discard the original cartridge as this serves as a plug when no fragrance cartridge is in use.
In order to preserve the service life of the cartridge, turn the dial fully to the left when you no longer wish to diffuse the fragrance in the passenger compartment.
The intensity of diffusion of the fragrance may depend on the ventilation or air conditioning settings.
as a safety precaution, do not carry out any action on the cartridge while driving.
do not dismantle the cartridges.
do not attempt to refill the fragrance diffuser or the cartridges.
Avoid all contact with the skin and eyes.
keep out of reach of children and animals.
Removing the cartridge
F Press the dial and turn it a quarter of a turn anti-clockwise.
F Remove the cartridge.
F Refit its sealing case.
3
Fitting the cartridge
F Remove the cartridge from the sealing case.
F Install the cartridge (flower at top left).
F Press the dial and turn it a quarter of a turn clockwise.
47
Comfort
Front seats
Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfort.
Adjustments
Forwards-backwards Height Seat backrest angle
48
F Raise the control and slide the seat forwards or backwards.
F Pull the control upwards to raise or push it downwards to lower, as many times as required, to obtain the position required.
F Push the control rearwards.
Before moving the seat backwards, ensure that there is nothing that might prevent the full travel of the seat, so as to avoid the risk of of jamming the seat caused by the presence of objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement immediately.
Additional adjustments
Head restraint height
F To raise the head restraint, pull it forwards and upwards at the same time.
F To remove the head restraint, press the lug A and pull the head restraint upwards.
F To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back.
F To lower the head restraint, press the lug
A and the head restraint at the same time.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact.
The adjustment is correct when the upper edge of the head restraint is level with the top of the head.
Never drive with the head restraints removed; they must be in place and adjusted correctly.
Comfort
3
49
Comfort
Rear seats
Bench seat with fixed one-piece cushion and split backrest (right hand 2/3, left hand 1/3) to adjust the load space in the boot.
Rear head restraints
These have one position for use (up) and a stowed position (down).
Folding the backrest Repositioning the seat backrest
50
They can also be removed.
To remove a head restraint:
F release the backrest using control 1 ,
F tilt the backrest 2
slightly forwards,
F pull the head restraint upwards to the stop,
F then, press the lug A .
F Move the corresponding front seat forward if necessary.
F Check that the seat belt is positioned correctly on the side of the seat backrest.
F Place the head restraints in the low position.
F Straighten the seat backrest 2 and secure it.
F Check that the red indicator, located next to the control 1 , is no longer visible.
When repositioning the seat backrest, take care not to trap the seat belts.
With passengers in the rear seats, never drive with the head restraints removed; they must be in place and correctly adjusted.
F Pull control 1
forwards to release the seat backrest 2 .
F Fold the seat backrest 2 on to the cushion.
Comfort
Mirrors
Door mirrors
Folding
F From outside: lock the vehicle using the remote control or the key.
F From inside: with the ignition on, with the control A in the central position, pull it downwards.
If the mirrors are folded using control A , they will not unfold when the vehicle is unlocked. Pull again on control A .
3
Each fitted with an adjustable mirror glass permitting the lateral rearward vision necessary for overtaking or parking. They can also be folded for parking in confined spaces.
Adjustment
F Move control A to the right or to the left to select the corresponding mirror.
F Move control B in all four directions to adjust.
F Return control A to the central position.
Demisting - Defrosting
If your vehicle is fitted with heated mirrors, the demisting-defrosting operates with the engine running, by switching on the heated rear screen
(refer to the "Rear screen demist-defrost" page).
The objects observed are, in reality, closer than they appear.
Take this into account in order to correctly judge the distance of vehicles approaching from behind.
Unfolding
F From outside: unlock the vehicle using the remote control or the key.
F From inside: with the ignition on, with the control A in the central position, pull it downwards.
The folding and unfolding of the door mirrors using the remote control can be deactivated by a CITRoËn dealer or a qualified workshop.
never fold or unfold the electric folding mirrors manually.
51
52
Comfort
Steering wheel adjustment
Rear view mirror
Adjustable mirror providing a central rearward view.
Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to the driver caused by the sun, headlamps from other vehicles...
Manual day/night model
Automatic day/night model
Adjustment
F adjust the mirror so that the glass is directed correctly in the "day" position.
Day / night position
F Pull the lever to change to the "night" antidazzle position.
F Push the lever to change to the normal
"day" position.
as a safety measure, the mirrors should be adjusted to reduce the "blind spot".
By means of a sensor, which measures the light from the rear of the vehicle, this system automatically and progressively changes between the day and night uses.
In order to ensure optimum visibility during your manoeuvres, the mirror lightens automatically when reverse gear is engaged.
F When stationary , pull the control lever to release the adjustment mechanism.
F adjust the height and reach to suit your driving position.
F Push the control lever to lock the adjustment mechanism.
as a safety precaution, these operations should only be carried out with the vehicle stationary.
Access
Remote control key
System which permits central unlocking or locking of the vehicle using the lock or from a distance. It is also used to locate and start the vehicle, as well as providing protection against theft.
Unlocking the vehicle
Unlocking is confirmed by rapid flashing of the direction indicators for approximately two seconds.
according to version, the door mirrors unfold at the same time.
If one of the doors or the boot is still open, the central locking does not take place.
When the vehicle is locked, if it is unlocked inadvertently, it will relock automatically after thirty seconds unless a door or the boot is open.
Locking the vehicle
Locking using the remote control
Unfolding the key
F First press this button to unfold the key.
F Press the closed padlock to lock the vehicle.
The folding and unfolding of the door mirrors using the remote control can be deactivated by a CITRoËn dealer or a qualified workshop.
Unlocking using the remote control
F Press the open padlock to unlock the vehicle.
Locking using the key
F Turn the key to the left in the driver's door lock to lock the vehicle completely.
4
Unlocking using the key
F Turn the key to the right in the driver's door lock to unlock the vehicle.
Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds.
according to version, the door mirrors fold at the same time.
53
54
Access
Deadlocking using the remote control
F Press the closed padlock to lock the vehicle completely.
F Press the closed padlock again within five seconds to deadlock the vehicle.
Deadlocking using the key
F Turn the key to the left in the driver's door lock to lock the vehicle completely.
F Turn the key to the left again within five seconds to deadlock the vehicle.
deadlocking is confirmed by fixed lighting of the direction indicators for approximately two seconds.
according to version, the door mirrors fold at the same time.
deadlocking renders the exterior and interior door controls inoperative.
It also deactivates the manual central control button.
Therefore, never leave anyone inside the vehicle when it is deadlocked.
Folding the key
F First press this button to fold the key.
If you do not press the button when folding the key, there is a risk of damage to the mechanism.
Access
Locating your vehicle
F Press the closed padlock to locate your locked vehicle in a car park.
This is indicated by lighting of the courtesy lamps and flashing of the direction indicators for a few seconds.
Anti-theft protection Ignition switch
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched on, this code must be recognised in order for starting to be possible.
This electronic engine immobiliser locks the engine management system a few minutes after the ignition is switched off and prevents starting of the engine by anyone who does not have the key.
In the event of a fault, you are informed by illumination of this warning lamp, an audible signal and a message in the screen.
In this case, your vehicle will not start; contact a CITRoËn dealer as soon as possible.
- Position 1: Stop
- Position 2:
Ignition
- Position 3: Starting
Keep safely, away from your vehicle, the label attached to the keys given to you on acquisition of the vehicle.
Starting the vehicle
F Insert the key in the ignition switch.
The system recognises the starting code.
F Turn the key fully towards the dashboard to position 3 (Starting) .
F When the engine starts, release the key.
4
55
Access
56
Switching the vehicle off
F Immobilise the vehicle.
F Turn the key fully towards you to position 1 (Stop) .
F Remove the key from the ignition switch.
do not attach any heavy objects to the key as this could weigh down on it when in the ignition switch and cause a fault.
Remote control problem
Following disconnection of the vehicle battery, replacement of the remote control battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your vehicle.
F First of all, use the key in the lock to unlock or lock your vehicle.
F Then, reinitialise the remote control.
Key reminder
If the key is left in the ignition switch, an audible signal sounds when the driver's door is opened.
Reinitialisation
F Switch off the ignition.
F Turn the key to position 2 (Ignition on) .
F Press the closed padlock immediately for a few seconds.
F Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is flat, you are informed by illumination of this warning lamp, an audible signal and a message.
F Unclip the casing using a coin at the notch.
F Slide the flat battery out of its location.
F Slide the new battery into its location observing the original direction.
F Clip the casing.
F Reinitialise the remote control.
If the problem persists, contact a CITRoËn dealer as soon as possible.
Lost keys
Go to a CITROËN dealer with the vehicle's registration document, your personal identification documents and if possible the key code label.
The CITROËN dealer will be able to look up the key code and the transponder code required to order a new key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without you being aware of it.
do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it from working and the remote control would have to be reinitialised.
No remote control can operate when the key is in the ignition switch, even when the ignition is switched off, except for reinitialisation.
Locking the vehicle
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
as a safety precaution, never leave children alone in the vehicle, except for a very short period.
In all cases, it is essential to remove the key from the ignition switch when leaving the vehicle.
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a CITRoËn dealer, to ensure that only your keys can be used to open and start the vehicle.
Access
Do not throw the remote control batteries away, they contain metals which are harmful to the environment.
Take them to an approved collection point.
4
57
58
Access
alarm
System which protects and provides a deterrent against the theft of your vehicle. It provides two types of protection, exterior and interior, as well as a self-protection function.
Exterior perimeter protection
The system detects opening of the vehicle.
The alarm is triggered if anyone tries to enter the vehicle by forcing a door, the boot or the bonnet.
Locking the vehicle with full alarm
If an opening - door or boot - is not closed fully, the vehicle is not locked, but the exterior perimeter protection will be activated after 45 seconds at the same time as the interior volumetric protection.
Interior volumetric protection
The system detects any variation in the volume in the passenger compartment.
The alarm is triggered if anyone breaks a window or moves inside the vehicle.
If you wish to leave a pet in the vehicle or a window partially open, deactivate the interior volumetric protection.
Self-protection function
The system detects the putting out of service of its components.
The alarm is triggered if anyone tries to put the wires of the siren, the central control or the battery out of service.
do not make any modifications to the alarm system, this could cause malfunctions.
Activation
F Switch off the ignition and get out of the vehicle.
F Lock or deadlock the vehicle using the locking button on the remote control.
The alarm is activated; the indicator lamp in button A flashes once per second.
The exterior perimeter protection is activated,
5 seconds after the locking button on the remote control is pressed.
The interior volumetric protection is activated,
45 seconds after the locking button on the remote control is pressed.
Deactivation
F Unlock the vehicle using the unlocking button on the remote control.
The alarm is deactivated; the indicator lamp in button A goes off.
Access
Locking the vehicle with exterior perimeter protection only
Deactivation of the interior volumetric protection
F Switch off the ignition.
F Within ten seconds, press button A until the indicator lamp is on continuously.
F Get out of the vehicle.
F Lock or deadlock the vehicle without delay using the locking button on the remote control.
The exterior perimeter protection alone remains activated; the indicator lamp in button
A flashes once per second.
To be effective, this deactivation must be carried out each time the ignition is switched off.
Triggering of the alarm
This is indicated by sounding of the siren and flashing of the direction indicators for approximately thirty seconds.
after it has been triggered, both types of protection are again operational.
If the alarm is triggered ten times in succession, the eleventh time will result in it becoming inactive.
If the indicator lamp in button A flashes rapidly, this indicates that the alarm was triggered during your absence. When the ignition is switched on, this flashing stops immediately.
To avoid triggering the alarm when washing your vehicle, lock it using the key in the driver's door lock.
Reactivation of the interior volumetric protection
F Unlock the vehicle using the unlocking button on the remote control.
F Relock the vehicle using the remote control.
The alarm is activated again with both types of protection; the indicator lamp in button
A flashes once per second.
Failure of the remote control
F Unlock the vehicle using the key in the driver's door lock.
F Open the door; the alarm is triggered.
F Switch on the ignition; the alarm stops.
Locking the vehicle without activating the alarm
F Lock or deadlock the vehicle using the key in the driver's or passenger's door lock.
Malfunction
When the ignition is switched on, illumination of the indicator lamp in button A for ten seconds indicates malfunction with the siren.
Have it checked by a CITRoËn dealer or a qualified workshop.
Automatic activation*
2 minutes after the last door or the boot is closed, the alarm is activated automatically.
F To avoid triggering the alarm on entering the vehicle, first press the unlocking button on the remote control.
* according to country.
4
59
60
Access
Window controls
System which opens or closes a window manually or automatically. It is fitted with a system which provides protection if an obstacle is detected on the one-touch models and a deactivation system to prevent misuse of the rear switches on all models.
The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until a front door is opened.
During this period of 45 seconds, if you open a door while opening a window, the window stops. The ignition must then be switched on again to operate the windows.
One-touch electric windows
There are two methods of operation:
1.
Driver's electric window.
2.
Passenger's electric window.
3.
Rear right electric window.
4.
Rear left electric window.
5.
Deactivating the rear electric window and door switches.
Electric windows
F Press or pull the switch. The window stops as soon as the switch is released.
- manual mode
F Press or pull the switch gently. The window stops as soon as the switch is released.
- automatic mode
F Press or pull the switch fully. The window opens or closes completely when the switch is released.
F Pressing the switch again stops the movement of the window.
Access
Safety anti-pinch
The one-touch front electric windows are fitted with a safety anti-pinch function.
When the window rises and meets an obstacle, it stops and partially lowers again.
In the event of unwanted opening of the window on closing (for example in the presence of frost):
F press the switch beyond the point of resistance and then release it: the window opens completely,
F then pull it immediately without passing the point of resistance until the window closes completely,
F continue to hold the switch for approximately one second after the window has closed.
The safety anti-pinch function is not active during these operations.
Deactivating the rear window and door switches
F
For the safety of your children, press switch
5 to prevent operation of the rear windows irrespective of their position.
With the lamp on, the rear controls are deactivated.
With the lamp off, the rear controls are activated.
This control also deactivates the interior rear door controls (see "Child safety -
§ Electric child lock").
Reinitialisation
In the event of a malfunction you have to reinitialise the operation of the electric windows:
F release the switch and pull it again until the window closes completely,
F hold the switch for approximately one second after closing,
F press the switch to lower the window automatically.
The safety anti-pinch function is not active during these operations.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
In the event of contact during operation of the windows, reverse the movement of the window. To do this, press the switch concerned.
When the driver operates the passenger electric window switches, they should ensure that no one is preventing correct closing of the windows.
The driver should ensure that passengers use the electric windows correctly.
Be particularly aware of children when operating the windows.
4
61
62
Access
doors
Opening
From outside
F after unlocking the vehicle using the remote control or the key, pull the door handle.
From inside
F Pull the front door control to open the door; this unlocks the vehicle completely.
F Pull the rear door control to open the door; this unlocks only the door opened.
Closing
When a door or the boot is not closed correctly:
- When the engine is running , this warning lamp comes on, accompanied by a message in the multifunction screen for a few seconds,
- When the vehicle is moving (speed higher than 6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message in the multifunction screen for a few seconds.
Version with deadlocking
The interior door controls do not operate when the vehicle is deadlocked.
Access
Manual central locking control
System which provides full manual locking or unlocking of the doors from the inside.
Locking
F Press button A to lock the vehicle.
The red indicator lamp on the button comes on.
Unlocking
F Press button A again to unlock the vehicle.
The red indicator lamp on the button switches off.
Automatic central locking
System which provides full automatic locking or unlocking of the doors and the boot while driving.
You can activate or deactivate this function.
4
If the vehicle is locked from the outside, the red indicator lamp flashes and button A is inactive.
F In this case, use the remote control or the key to unlock the vehicle.
Driving with the doors locked can make access more difficult for the emergency services in the event an emergency.
Locking
When the speed exceeds 6 mph (10 km/h), the doors and the boot lock automatically.
If one of the doors is open, the automatic central locking does not take place.
If the boot is open, the automatic central locking of the doors is active.
Unlocking
F above 6 mph (10 km/h), press button A to unlock the doors and the boot temporarily.
If one of the doors is open, central locking from the inside does not take place.
63
64
Access
Emergency control
To lock or unlock the doors manually in the event of a malfunction of the central locking system or failure of the battery.
Locking the front and rear passenger doors
Check that the rear doors child lock is not on.
In the event of a malfunction with the central locking system, the battery must be disconnected to lock the boot and so secure the vehicle completely.
Activation
F Press button A
for more than two seconds.
a confirmation message appears on the multifunction screen, accompanied by an audible signal.
Deactivation
F Press button A again for more than two seconds.
a confirmation message appears on the multifunction screen, accompanied by an audible signal.
Driving with the doors locked may make access more difficult for the emergency services in an emergency.
Locking the driver's door
F Insert the key in the lock, then turn it to the left.
Unlocking the driver's door
F Insert the key in the lock, then turn it to the right.
F Remove the black cap, located on the edge of the door, using the key.
F Insert the key in the recess, then turn it as far as it will go.
F Remove the key and refit the cap.
Unlocking the front and rear passenger doors
F Pull the interior door opening control.
Access
boot
Opening
F after unlocking the vehicle using the remote control or the key, pull the handle and raise the tailgate.
Closing
F Lower the tailgate using the interior grab handle.
If the tailgate is not closed correctly:
- when the engine is running , this warning lamp comes on, accompanied by a message on the multifunction screen for a few seconds,
- when the vehicle is moving (speed above
6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message on the multifunction screen for a few seconds.
Tailgate release
System for mechanical unlocking of the boot in the event of a battery or central locking malfunction.
Unlocking
F Fold back the rear benchseat to gain access to the lock from inside the boot.
F Insert a small screwdriver into hole
A of the lock to unlock the tailgate.
4
65
66
Access
Fuel tank
Fuel tank capacity: approximately
50 litres (petrol) or 46 litres (Diesel) or
37 litres (LPG); (Depending on version: approximately 30 litres (petrol or Diesel)).
Low fuel level
When the fuel tank minimum level is reached this warning lamp comes on on the instrument panel. When it first comes on there remains approximately
5 litres of fuel in the tank.
You must refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (diesel), refer also to the
"Checks" section.
To fill the tank safely:
F the engine must be switched off,
F open the fuel filler flap,
F insert the key in the cap, then turn it to the left,
F remove the cap and hook it onto the clip located on the inside of the flap,
F fill the tank, but do not continue after the
3rd cut-off of the pump
; this could cause malfunctions.
Filling
a label affixed to the inside of the flap reminds you of the type of fuel to be used depending on your engine.
Additions of fuel must be of at least 7 litres, in order to be registered by the fuel gauge.
With Stop & Start, never refuel with the system in STOP mode; you must switch off the ignition with the key.
When you have filled the tank:
F put the cap back in place,
F turn the key to the right, then remove it from the cap,
F close the flap.
The key cannot be removed from the lock until the cap is refitted.
opening the filler cap may create a noise caused by an inrush of air. This vacuum is entirely normal, resulting from the sealing of the fuel system.
Fuel used for petrol engines
The petrol engines are compatible with
E10 bio-petrol (containing 10 % ethanol), conforming to European standards EN 228 and EN 15376.
E85 type fuels (containing up to 85 % ethanol) are reserved exclusively for vehicles marketed for the use of this type of fuel (bioFlex vehicles). The quality of the ethanol must comply with European standard EN 15293.
Fuel used for Diesel engines
The Diesel engines are perfectly with biofuels which conform to current and future European standards (Diesel fuel which complies with standard EN 590 mixed with a biofuel which complies with standard EN 14214) available at the pumps (containing up to 7 % Fatty Acid
Methyl Ester).
The b30 biofuel can be used in certain diesel engines; however, this use is subject to strict application of the special servicing conditions indicated in the maintenance and warranty guide. Contact a CITRoËn dealer or a qualified workshop.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or diluted, domestic fuel...) is strictly prohibited (risk of damage to the engine and fuel system).
Access
4
67
68
Access
Misfuel prevention (diesel)*
Operation
When a petrol filler nozzle is introduced into the fuel filler neck of your diesel vehicle, it comes into contact with the flap. The system remains closed and prevents filling.
Do not persist but introduce a Diesel type filler nozzle.
Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong fuel.
Located in the filler neck, the misfuel prevention device appears when the filler cap is removed.
It remains possible to use a fuel can to fill the tank.
In order to ensure a good flow of fuel, do not place the nozzle of the fuel can in direct contact with the flap of the misfuel prevention device and pour slowly.
Travelling abroad
as diesel fuel pump nozzles may be different in other countries, the presence of the misfuel prevention device may make refuelling impossible.
Before travelling abroad, we recommend that you check with the
CITROËN dealer network, whether your vehicle is suitable for the fuel pumps in the country in which you want to travel.
* according to country of sale.
Visibility
Lighting controls
System for selection and control of the various front and rear lamps providing the vehicle's lighting.
Main lighting
The various front and rear lamps of the vehicle are designed to adapt the driver's visibility progressively according to climatic conditions:
- sidelamps, to be seen,
- dipped beam headlamps to see without dazzling other drivers,
- main beam headlamps to see clearly when the road is clear.
Manual controls
The lighting is controlled directly by the driver by means of the ring A and the stalk B .
Model without AUTO lighting
A.
Main lighting mode selection ring: turn it to position the symbol required facing the mark.
Lighting off / daytime running lamps.
automatic illumination of headlamps.
5
Sidelamps only.
Additional lighting
other lamps are installed to fulfil the requirements of particular conditions of visibility:
- a rear foglamp to be seen from afar,
- front foglamps for even better forward vision.
Programming
Various automatic lighting control modes are also available according to the following options:
- guide-me-home lighting,
- automatic illumination of headlamps.
Model with AUTO lighting
dipped or main beam headlamps.
B.
Stalk for switching the headlamp beam: pull the stalk to switch between dipped and main beam headlamps.
In the lamps off and sidelamps modes, the driver can switch on the main beam headlamps temporarily ("headlamp flash") by maintaining a pull on the stalk.
Displays
Lighting of the corresponding indicator lamp on the instrument panel confirms the switching on of the lighting selected.
depending on version, the instrument panel may have permanent back-lighting. Illumination of the instrument panel is therefore not linked to the exterior lighting.
69
Visibility
70
Model with rear foglamp only
Model with front foglamps and a rear foglamp
C.
Foglamp selection ring.
The foglamps operate with the dipped and main beam headlamps.
Rear foglamp
F To switch on the foglamp, turn the ring
C forwards.
When the lighting is switched off automatically
(with AUTO model), the foglamp and the dipped beam headlamps will remain on.
F To switch off all of the lighting, turn the ring C
rearwards.
Front and rear foglamps
When the lighting is switched off automatically
(with AUTO model) or when the dipped headlamps are switched off manually, the foglamps and sidelamps will remain on.
F Turn the ring rearwards to switch off the foglamps, the sidelamps will then switch off.
In good or rainy weather, by both day and night, the front foglamps and the rear foglamp are prohibited. In these situations, the power of their beams may dazzle other drivers.
Do not forget to switch off the front foglamps and the rear foglamp when they are no longer necessary.
Rotate and release the ring C :
F forwards a first time to switch on the front foglamps,
F forwards a second time to switch on the rear foglamp,
F rearwards a first time to switch off the rear foglamp,
F rearwards a second time to switch of the front fog lamps.
Lighting on audible warning
When the ignition is switched off, all of the lamps switch off automatically, unless guide-me-home lighting is activated.
If the lighting is switched on manually after switching off the ignition, there is an audible signal when a front door is opened to warn the driver that they have forgotten to switch off the vehicle's lighting, with the ignition off.
Manual guide-me-home lighting
The temporary illumination of the dipped beam headlamps after the vehicle's ignition has been switched off makes the driver's exit easier when the light is poor.
In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal surface of the glass of the headlamps and rear lamps is normal; it disappears after the lamps have been on for a few minutes.
Switching on
F With the ignition off, "flash" the headlamps using the lighting stalk.
F A further "headlamp flash" switches the function off.
Switching off
The manual guide-me-home lighting switches off automatically after a set time.
Visibility
5
71
72
Visibility
Automatic illumination of headlamps
The sidelamps and dipped beam headlamps are switched on automatically, without any action on the part of the driver, when a low level of external light is detected or in certain cases of activation of the windscreen wipers.
as soon as the brightness returns to a sufficient level or after the windscreen wipers are switched off, the lamps are switched off automatically.
Activation
F Turn ring to the "AUTO" position. The automatic illumination of headlamps is accompanied by a message in the screen.
Deactivation
F Turn ring to a position other than "AUTO" . deactivation is accompanied by a message in the screen.
Association with the automatic
"Guide-me-home" lighting
Association with the automatic illumination of headlamps provides "guide-me-home" lighting with the following additional options:
- selection of the lighting duration to 15, 30 or
60 seconds in the functions that can be set in the vehicle configuration menu (except in the case of the monochrome screen a, for which the duration is set: 60 seconds),
- automatic activation of "guide-me-home" lighting when automatic illumination of headlamps is in operation.
Operating fault
In the event of a fault with the sunshine sensor, the lighting come on, this warning lamp is displayed in the instrument panel and/or a message appears in the screen, accompanied by an audible signal.
Contact a CITRoËn dealer or a qualified workshop.
In fog or snow, the sunshine sensor may detect sufficient light. Therefore, the lighting will not come on automatically.
do not cover the sunshine sensor, coupled with the rain sensor and located in the centre of the windscreen behind the rear view mirror; the associated functions would no longer be controlled.
Visibility
LEd lamps
Allowing the signature of the vehicle to be identified, this daytime external lighting comprises two sets of six light emitting diodes (LEDs), located below each front lamp unit.
Programming
For countries where exterior lighting by day is not a legal requirement, you can activate or deactivate the function via the multifunction screen configuration menu.
on starting the vehicle, in daylight the LEd lamps come on automatically, if the lighting stalk is in position "0" or "AUTO" .
If the sidelamps and headlamps are switched on manually or automatically, the LEd lamps switch off.
Headlamp adjustment
In countries where daytime lamps are a legal requirement:
- this function is activated by default; it cannot be deactivated,
- in daylight, the sidelamps and number plate lamps also come on,
- If the sidelamps or headlamps are switched on manually or automatically, the LEd lamps switch off.
In these countries, for versions not fitted with LED lamps, it is the dipped beam headlamps that come on automatically on starting the vehicle.
To avoid causing a nuisance to other road users, the height of the headlamps should be adjusted in relation to the load in the vehicle.
0.
driver only or driver + front passenger.
-.
Intermediate setting
1.
5 people.
-.
5 people + load in the boot.
2.
driver only + maximum authorised load in the boot.
This position is sufficient to avoid causing dazzle.
Higher settings may limit the spread of light from the headlamps.
5
The initial setting is position "0" .
73
74
Visibility
Wiper controls
System for selection and control of the various front and rear wiping modes for the elimination of rain and cleaning.
The vehicle's front and rear wipers are designed to improve the driver's visibility progressively according to the climatic conditions.
Model with intermittent wiping
Programming
Various automatic wiper control modes are also available according to the following options:
- automatic rain sensitive windscreen wipers,
- rear wiping on engaging reverse gear.
Model with AUTO wiping
Manual controls
The wiper commands are issued directly by the driver by means of the stalk A and the ring B .
Windscreen wipers
A.
Wiping speed selection stalk.
Fast (heavy rain).
normal (moderate rain).
Intermittent (proportional to the speed of the vehicle).
off.
Single wipe (press down and release).
or
Automatic, then single wipe
(see the corresponding section).
Visibility
Rear wiper
B.
Rear wiper selection ring: park, intermittent wipe, wash-wipe (set duration).
If a significant accumulation of snow or ice is present, or when using a tailgate bicycle carrier, deactivate the automatic rear wiper via the multifunction screen configuration menu.
Reverse gear
When reverse gear is engaged, the rear wiper will come into operation if the windscreen wipers are operating.
Programming
The function is activated or deactivated via the vehicle configuration menu.
This function is activated by default.
Windscreen wash
Pull the wiper stalk towards you.
The windscreen wash, then the windscreen wipers, operate for a pre-determined time.
5
75
Visibility
76
Automatic rain sensitive windscreen wipers
The windscreen wipers operate automatically, without any action on the part of the driver, if rain is detected (sensor behind the rear view mirror), adapting their speed to the intensity of the rainfall.
Activation
This is controlled manually by the driver by pushing stalk A to the "AUTO" position.
It is accompanied by the illumination of this indicator lamp in the instrument panel and a message in the multifunction screen.
Switching off
This is controlled manually by the driver by moving stalk A
upwards, returning it to position "0" .
It is accompanied by the indicator lamp in the instrument panel going off and a message in the multifunction screen.
The automatic wiping must be reactivated if the ignition has been off for more than one minute, by pushing stalk A
downwards.
Operating fault
If an automatic wiping fault occurs, the wipers will operate in intermittent mode.
Have it checked by a CITRoËn dealer or a qualified workshop.
Do not cover the rain sensor, linked with the sunshine sensor and located in the centre of the windscreen behind the rear view mirror.
Switch off the automatic wiping when using an automatic car wash.
In winter, it is advisable to wait until the windscreen is completely clear of ice before activating the automatic wiping.
Vertical windscreen wiper position
This position allows the wiper blades to be lifted for winter parking, cleaning or replacement without damaging the bonnet.
In the minute following switching off of the ignition, any action on the wiper stalk positions the wipers vertically.
To park the wipers after this has been done, switch on the ignition and operate the wiper stalk.
To retain the effectiveness of the flat wiper blades, it is advisable to:
- handle them with care,
- clean them regularly using soapy water,
- not use them to hold a sheet of cardboard against the windscreen,
- replace them at the first signs of wear.
Visibility
Courtesy lamps
Selection and control of the various passenger compartment lamps.
Central or rear courtesy lamps
In this position, the courtesy lamp comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when a door is opened,
- when the remote control locking button is activated, in order to locate your vehicle.
Version without Zenith windscreen
A.
Central courtesy lamp
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Version with Zenith windscreen
1.
Rear side reading lamps
2.
Rear courtesy lamp
Permanently off.
Permanent lighting.
In permanent lighting mode, the lighting duration varies, according to the circumstances:
- with the ignition off, approximately ten minutes,
- in energy economy mode, approximately thirty seconds,
- with the engine running, unlimited.
To switch off the rear courtesy lamp, place it in the "permanently off" position.
Front side reading lamps
F With the ignition on, the first press of the corresponding switch switches on the reading lamp concerned in permanent lighting mode.
F Following a second press, it comes on:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when a door is opened,
- when the remote control locking button is pressed, in order to locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
5
77
78
Visibility
Interior mood lighting
The dimmed passenger compartment lighting improves visibility in the vehicle when the light is poor.
Switching on
at night, the illumination of the central dashboard storage compartment comes on automatically when the sidelamps are switched on.
on certain versions, three lamps located in the support between the roof and the automatic day/night interior mirror come on as well.
boot lamp
Switching off
The interior mood lighting switches off automatically when the sidelamps are switched off.
It can be switched off manually using the instrument panel lighting rheostat button.
F With the lighting on, press several times on the left hand button of the instrument panel to progressively reduce the dashboard lighting level.
F Press again to reduce the lighting level to the minimum and switch off the interior mood lighting.
This comes on automatically when the boot is opened and goes off automatically when the boot is closed.
The lighting time varies according to the circumstances:
- when the ignition is off, approximately ten minutes,
- in energy economy mode, approximately thirty seconds,
- when the engine is running, no limit.
Interior fittings
1.
Sun visor
2.
Glove box
(details on following page)
3.
Storage compartments
4.
Door pockets
5.
Upper storage compartment
6.
Lower storage compartment with nonslip mat
7.
USB port / auxiliary socket
(details on following page)
or
Coin holder
8.
12 V accessories socket
(details on following page)
9.
Centre armrest with storage
(details on following page)
or
Cup / bottle holder
Fittings
6
79
80
Fittings
Zenith Windscreen
Blind Sun visors
System comprising a panoramic tinted glass area to increase lighting and vision in the cabin.
Fitted with a manual blind to improve thermal comfort and sun visors to avoid dazzle.
F To open the blind, take it by its central grip A
, then pull it backwards and guide it to the desired position.
F To close the blind, take it by its central grip A
, then pull it forwards and guide it to the desired position.
before moving the blind, the sun visors must be in the folded position.
F Lower the sun visors to avoid dazzle.
do not attach or hang heavy objects to the blind or its guide rails.
Sun visor
Component which protects against sunlight from the front or the side.
Glove box
Fittings
Centre armrest
Comfort and storage system for the driver and front passenger.
Storage
Version without Zenith windscreen
The sun visors are fitted with a courtesy mirror, with concealing flap for the driver and a ticket / card holder.
Version with Zenith windscreen
Refer to the "Familiarisation - Zenith windscreen" section.
F To open the glove box, raise the handle.
It houses the front passenger airbag deactivation switch
A .
It gives access to the dashboard fusebox (see the "Practical information - § Changing a fuse" section).
F For access to the closed storage box, lift the lever to open the lid.
F For access to the open storage box below the armrest, lift the complete armrest towards the rear.
These can be used for portable devices (mobile phone, MP3 player...) which can be connected to the USb port / auxiliary socket or charged from the 12 V socket in the centre console.
6
81
Fittings
auxiliary socket USb Player
12 V accessory socket
82
The auxiliary socket is located in the " AUX " box on the centre console.
It permits the connection of a portable device, such as a digital audio player of the iPod ® type, to listen to your music files using the vehicle's speakers.
The management of the files is done using your portable device.
For more information on the use of this equipment, refer to the "audio system" or
"eMyWay" section.
The USb port is located in the "AUX" box on the centre console.
It permits the connection of a portable device, such as a digital audio player of the iPod ® generation 5 and later type or USB memory stick type.
It reads the audio file formats (mp3, ogg, wma, wav...) which are transmitted to your audio equipment and played via the vehicle's speakers.
You can manage these files using the steering mounted controls or the audio equipment control panel and display them on the multifunction screen.
When it is in use, the portable device charges automatically.
F To connect a 12 V accessory (max power:
120 W), lift the cover and connect a suitable adaptor.
For more information on the use of this equipment, refer to the "audio system" section.
Fittings
Storage drawer
Mats
Removable carpet protection.
The storage drawer is located under the driver's seat.
Opening
F Raise the front of the drawer and pull it.
Removal
F Bring the drawer to the end of its travel.
F
Press the ends of the slides.
F Raise the drawer and pull it fully.
Refitting
F Engage the drawer in its slides.
F at the end of its travel, press on the top of the drawer to secure it.
do not place heavy objects in the drawer.
Fitting
When fitting the mat for the first time, on the driver's side use only the fixings provided in the wallet attached.
The other mats are simply placed on the carpet.
Removal
To remove the mat on the driver's side:
F move the seat as far back as possible,
F unclip the fixings,
F remove the mat.
Refitting
To refit the mat on the driver's side:
F
position the mat correctly,
F
refit the fixings by pressing,
F
check that the mat is secured correctly.
To avoid any risk of jamming of the pedals:
- only use mats which are suited to the fixings already present in the vehicle; these fixings must be used,
- never fit one mat on top of another.
The use of mats not approved by
CITROËN may interfere with access to the pedals and hinder the operation of the cruise control / speed limiter.
The mats approved by CITRoËn have two fixings located below the seat.
6
83
84
Fittings
Boot fittings
1.
Rear parcel shelf
(see following page for details)
2.
Hooks
(see following page for details)
3.
Location for Hi-Fi amplifier
4.
Stowing rings
5.
Storage box (version equipped with a temporary puncture repair kit)
(see following page for details)
or
Tool box (version equipped with a spare wheel)
(refer to section "Practical Information - §
Changing a wheel")
Rear parcel shelf Hooks Storage box
Fittings
To remove the shelf:
F unhook the two cords,
F raise the shelf slightly, then unclip it on each side.
The hooks can be used to hold shopping bags.
F Raise the boot carpet by pulling the strap upwards to gain access to the storage box.
This has areas for storing a temporary puncture repair kit, a box of spare bulbs, a first aid kit, two warning triangles, ...
6
F refit the boot floor carpet by folding it slightly in the middle.
85
Child safety
General points relating to child seats
Although one of CITROËN main criteria when designing your vehicle, the safety of your children also depends on you.
For maximum safety, please observe the following recommendations:
- in accordance with European regulations, all children under the age of 12 or less than one and a half metres tall must travel in approved child seats suited to their weight
, on seats fitted with a seat belt or ISoFIX mountings*,
- statistically, the safest seats in your vehicle for carrying children are the rear seats,
- a child weighing less than 9 kg must travel in the "rearward facing" position both in the front and in the rear.
CITROËN recommends that children should travel on the rear seats of your vehicle:
- "rearward-facing" up to the age of 3,
- "forward-facing" over the age of 3.
86
* The regulations on carrying children are specific to each country. Refer to the legislation in force in your country.
Child seat at the rear
"Rearward facing" "Forward facing"
Child safety
Centre rear seat
A child seat with a support leg must never be installed on the centre rear passenger seat .
7
When a "rearward facing" child seat is installed on a rear passenger seat , move the vehicle's front seat forwards and straighten the backrest so that the "rearward facing" child seat does not touch the vehicle's front seat.
When a "forward facing" child seat is installed on a rear passenger seat , move the vehicle's front seat forwards and straighten the backrest so that the legs of the child in the "forward facing" child seat do not touch the vehicle's front seat.
Ensure that the seat belt is correctly tensioned.
For child seats with a support leg, ensure that this is in firm contact with the floor. If necessary, adjust the front seat of the vehicle.
87
Child safety
Child seat in the front*
"Rearward facing" "Forward facing"
88
When a "rearward facing" child seat is installed on the front passenger seat , adjust the seat to the intermediate longitudinal position, with the backrest straightened.
The passenger's front airbag must be deactivated. Otherwise, the child would risk being seriously injured or killed if the airbag were to inflate .
When a "forward facing" child seat is installed on the front passenger seat , adjust the vehicle's seat to the intermediate longitudinal position with seat backrest straightened and leave the passenger's front airbag activated.
Passenger seat adjusted to the intermediate longitudinal position.
* The rules on carrying children are specific to each country. Refer to the current legislation in your country before installing a child seat on this seat.
Ensure that the seat belt is correctly tensioned.
For child seats with a support leg, ensure that the support leg is in stable contact with the floor. If necessary, adjust the passenger seat.
Child safety
deactivating the passenger's front airbag
Never install a rearward facing child restraint system on a seat protected by an active front airbag. This could cause the death of the child or serious injury.
The warning label present on both sides of the passenger's sun visor repeats this advice. In line with current legislation, the following tables contain this warning in all of the languages required.
Passenger airbag OFF
7
For information on deactivating the passenger's front airbag, refer to the
"airbags" section.
89
90
Child safety aR bG
НИКОГА НЕ инсталирайте детско столче на седалка с АКТИВИРАНА предна ВЪЗДУШНА ВЪЗГЛАВНИЦА. Това може да причини
СМЪРТ или СЕРИОЗНО НАРАНЯВАНЕ на детето.
CS
NIKDY neumisťujte dětské zádržné zařízení orientované směrem dozadu na sedadlo chráněné AKTIVOVANÝM čelním AIRBAGEM. Hrozí nebezpečí SMRTI DÍTĚTE nebo VÁŽNÉHO ZRANĚNÍ.
da brug aLdRIG en bagudvendt barnestol på et sæde, der er beskyttet af en akTIV aIRbaG. baRnET risikerer at blive aLVoRLIGT kVÆSTET eller dRÆbT.
dE Montieren Sie auf einem Sitz mit akTIVIERTEM Front-airbag nIEMaLS einen kindersitz oder eine babyschale entgegen der Fahrtrichtung, das Kind könnte schwere oder sogar tödliche Verletzungen erleiden.
EL
Μη χρησιμοποιείτε ΠΟΤΕ παιδικό κάθισμα με την πλάτη του προς το εμπρός μέρος του αυτοκινήτου, σε μια θέση που προστατεύεται από
ΜΕΤΩΠΙΚΟ αερόσακο που είναι ΕΝΕΡΓΟΣ. Αυτό μπορεί να έχει σαν συνέπεια το ΘΑΝΑΤΟ ή το ΣΟΒΑΡΟ ΤΡΑΥΜΑΤΙΣΜΟ του ΠΑΙΔΙΟΥ
En
NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the
CHILd can occur
ES no InSTaLaR nUnCa un sistema de retención para niños de espaldas al sentido de la marcha en un asiento protegido mediante un
AIRBAG frontal ACTIVADO, ya que podría causar lesiones GRAVES o incluso la MUERTE del niño.
ET Ärge MITTE kUnaGI paigaldage "seljaga sõidusuunas" lapseistet juhi kõrvalistmele, mille ESITURVaPadI on akTIVEERITUd. Turvapadja avanemine võib last TÕSISELT või ELUoHTLIkULT vigastada.
FI ÄLÄ koSkaan aseta lapsen turvaistuinta selkä ajosuuntaan istuimelle, jonka edessä suojana on käyttöön aktivoitu TURVaTYYnY. Sen laukeaminen voi aiheuttaa LaPSEn kUoLEMan tai VakaVan LoUkkaanTUMISEn.
FR
NE JAMAIS installer de système de retenue pour enfants faisant face vers l’arrière sur un siège protégé par un COUSSIN GONFLABLE frontal ACTIVÉ.
Cela peut provoquer la MORT de l’ENFANT ou le BLESSER GRAVEMENT
HR
NIKADA ne postavljati dječju sjedalicu leđima u smjeru vožnje na sjedalo zaštićeno UKLJUČENIM prednjim ZRAČNIM JASTUKOM. To bi moglo uzrokovati SMRT ili TEŠKU OZLJEDU djeteta.
HU
SOHA ne használjon menetiránynak háttal beszerelt gyermekülést AKTIVÁLT (BEKAPCSOLT) FRONTLÉGZSÁKKAL védett ülésen. Ez a gyermek HALÁLÁT vagy SÚLYOS SÉRÜLÉSÉT okozhatja.
IT non installare MaI seggiolini per bambini posizionati in senso contrario a quello di marcia su un sedile protetto da un aIRbaG frontale aTTIVaTo. Ciò potrebbe provocare la MoRTE o FERITE GRaVI al bambino.
LT
NIEKADA neįrenkite vaiko prilaikymo priemonės su atgal atgręžtu vaiku ant sėdynės, kuri saugoma VEIKIANČIOS priekinės ORO
PAGALVĖS. Išsiskleidus oro pagalvei vaikas gali būti MIRTINAI arba SUNKIAI TRAUMUOTAS.
LV
NEKAD NEuzstādiet uz aizmuguri vērstu bērnu sēdeklīti priekšējā pasažiera sēdvietā, kurā ir AKTIVIZĒTS priekšējais DROŠĪBAS GAISA
SPILVEnS.
Tas var izraisīt BĒRNA NĀVI vai radīt NOPIETNUS IEVAINOJUMUS.
Child safety
MT
Qatt m’ghandek thalli tifel/tifla marbut f’siggu dahru lejn l-Airbag attiva, ghaliex tista’ tikkawza korriment serju jew anke mewt lit-tifel/tifla nL
Plaats NOOIT een kinderzitje met de rug in de rijrichting op een zitplaats waarvan de AIRBAG is INGESCHAKELD. Bij het afgaan van de airbag kan het KIND LEVENSGEVAARLIJK GEWOND RAKEN no
Installer ALDRI et barnesete med ryggen mot kjøreretningen i et sete som er beskyttet med en frontal AKTIVERT KOLLISJONSPUTE, baRnET risikerer å bli dREPT eller HaRdT SkadET.
PL
NIGDY nie instalować fotelika dziecięcego w pozycji "tyłem do kierunku jazdy" na siedzeniu wyposażonym w CZOŁOWĄ PODUSZKĘ
POWIETRZNĄ w stanie AKTYWNYM. Może to doprowadzić do ŚMIERCI DZIECKA lub spowodować u niego POWAŻNE OBRAŻENIA
CIAŁA.
PT nUnCa instale um sistema de retenção para crianças de costas para a estrada num banco protegido por um aIRbaG frontal aCTIVado.
Esta instalação poderá provocar FERIMENTOS GRAVES ou a MORTE da CRIANÇA.
Ro nu instalati nICIodaTa un sistem de retinere pentru copii, dispus cu spatele in directia de mers, pe un loc din vehicul protejat cu aIRbaG frontal aCTIVaT. aceasta ar putea provoca MoaRTEa CoPILULUI sau RanIREa lui GRaVa.
RU
ВО ВСЕХ СЛУЧАЯХ ЗАПРЕЩАЕТСЯ использовать обращенное назад детское удерживающее устройство на сиденье, защищенном ФУНКЦИОНИРУЮЩЕЙ ПОДУШКОЙ БЕЗОПАСНОСТИ, установленной перед этим сиденьем.
Это может привести к ГИБЕЛИ РЕБЕНКА или НАНЕСЕНИЮ ЕМУ СЕРЬЕЗНЫХ ТЕЛЕСНЫХ ПОВРЕЖДЕНИЙ
Sk
NIKDY neinštalujte detské zádržné zariadenie orientované smerom dozadu na sedadlo chránené AKTIVOVANÝM čelným AIRBAGOM.
Mohlo by dôjsť k SMRTEĽNÉMU alebo VÁŽNEMU PORANENIU DIEŤAŤA.
SL
NIKOLI ne nameščajte otroškega sedeža s hrbtom v smeri vožnje, če je VARNOSTNA BLAZINA pred sprednjim sopotnikovim sedežem
AKTIVIRANA. Takšna namestitev lahko povzroči SMRT OTROKA ali HUDE POŠKODBE.
SR
NIKADA ne koristite dečje sedište koje se okreće unazad na sedištu zaštićenim AKTIVNIM VAZDUŠNIM JASTUKOM ispred njega, jer mogu nastupiti SMRT ili OZBILJNA POVREDA DETETA.
SV Passagerarkrockkudden fram MÅSTE vara avaktiverad om en bakåtvänd bilbarnstol installeras på denna plats. annars riskerar barnet att dÖdaS eller SkadaS aLLVaRLIGT.
TR
KESİNLKLE HAVA YASTIĞI AKTİF olan ön koltuğa yüzü arkaya dönük bir çocuk koltuğu yerleştirmeyiniz. Bu ÇOCUĞUN ÖLMESİNE veya
ÇOK AĞIR YARALANMASINA sebep olabilir.
7
91
92
Child safety
Child seats recommended by CITRoËn
CITROËN offers a range of recommended child seats which are secured using a three point seat belt .
Group 0+: from birth to 13 kg
L1
"RÖMER baby-Safe Plus"
Installed in the rearward facing position.
Groups 2 and 3: from 15 to 36 kg
L4
"kLIPPan optima"
From 22 kg (approximately 6 years), the booster is used on its own.
L5
"RÖMER kIdFIX"
Can be fitted to the vehicle's ISoFIX mountings.
The child is restrained by the seat belt.
Child safety
Installing child seats attached using the seat belt
In accordance with European regulations, this table indicates the options for installing child seats secured using a seat belt and universally approved
(a) in accordance with the weight of the child and the seat in the vehicle.
Seat
Front passenger seat (c) outer rear seats
Centre rear seat
Under 13 kg
(groups 0 (b) and 0+)
Up to approx 1 year
Weight of the child and indicative age
From 9 to 18 kg
(group 1)
1 to 3 years approx
From 15 to 25 kg
(group 2)
3 to 6 years approx
U U U
From 22 to 36 kg
(group 3)
6 to 10 years approx
U
U
U
U
U
(a) Universal child seat: child seat that can be installed in all vehicles using a seat belt.
(b) Group 0: from birth to 10 kg. Shells seats and baby carriers cannot be installed in the front passenger seat. When installed in the 2 nd
row, they may prevent use of the other seats.
(c) Consult the legislation in force in your country before installing your child on this seat.
U : Seat suitable for the installation of a child seat secured using a seat belt and universally approved, "rearward facing" and/or "forward facing".
U
U
U
U
Remove and stow the head restraint before installing a child seat with a backrest on a passenger seat. Refit the head restraint once the child seat has been removed.
7
93
94
Child safety
"ISoFIX" mountings
Your vehicle has been approved in accordance with the latest ISoFIX regulation .
The seats, represented below, are fitted with regulation ISoFIX mountings:
There are three rings for each seat:
- a ring B , behind the seat, referred to as the
TOP TETHER for fixing the upper strap.
To secure the child seat to the top tether:
- remove and stow the head restraint before installing the child seat on this seat (refit it once the child seat has been removed),
- pass the child seat strap over the top of the backrest of the seat, keeping it centred between the head restraint apertures,
- secure the hook of the upper strap to the ring B ,
- tighten the upper strap.
When fitting an ISoFIX child seat to the right hand rear seat, before fixing the seat in place, first move the centre rear seat belt towards the middle of the vehicle so as to not interfere with the operation of the seat belt.
The TOP TETHER is used to secure the upper strap of child seats that have one. This arrangement limits the forward tipping of the child seat in the event of a front impact.
This ISoFIX mounting system provides fast, reliable and safe fitting of the child seat in your vehicle.
The ISOFIX child seats
are fitted with two latches which are secured on the two rings
A .
Some seats also have an upper strap
which is attached to ring B .
The incorrect installation of a child seat in a vehicle compromises the child's protection in the event of an accident.
Follow strictly the advice given in the installation instructions provided with the child seat.
- two rings
A
, located between the vehicle seat back and cushion, indicated by a label,
Refer to the table for the possibilities for fitting
ISoFIX child seats in your vehicle.
Child safety
ISoFIX child seat recommended by CITRoËn and approved for your vehicle
RÖMER Duo Plus ISOFIX
(size category B1 )
Group 1: from 9 to 18 kg
Installed only in the forwards-facing position.
Fitted with an upper strap to be secured on the upper ring
B , referred to as the ToP TETHER.
Three seat body angles: sitting, reclining, lying.
adjust the front seat of the vehicle so that the child's feet do not touch the back of the seat.
Can be installed forwards-facing by attaching it to the seat using a three-point seat belt
7
This child seat can also be used on seats which are not fitted with ISOFIX mountings. In this case, it must be attached to the vehicle seat using the three point seat belt.
Follow the instructions for fitting the child seat given in the seat manufacturer's installation guide.
95
96
Child safety
Installing ISoFIX child seats
In accordance with European regulations, this table indicates the options for the installation of ISOFIX child seats on the vehicle seats fitted with
ISoFIX mountings.
In the case of the universal and semi-universal ISOFIX child seats, the child seat's ISOFIX size category, determined by a letter between
A and G , is indicated on the child seat next to the ISoFIX logo.
Type of ISOFIX child seat
Less than 10 kg
(group 0) approx
Up to 6 months
Infant car seat
Weight of the child and indicative age
Less than 10 kg
(group 0)
Less than 13 kg
(group 0+)
Up to 1 year approx
From 9 to 18 kg (group 1)
From 1 to 3 years approx
"rear facing" "rear facing" "forward facing"
C D A B B1 ISOFIX size category F G C D E
Universal and semi-universal ISOFIX child seats which can be installed on the outer rear seats
X X IL-SU
IUF: seat suitable for the installation of an I sofix U niversal seat, " F orward facing" and secured using the "ToP TETHER" upper strap.
IL-SU: seat suitable for the installation an I sofix S emiU niversal seat which is:
- "rearward facing" fitted with a "Top Tether" upper strap or a stay,
- "forward facing" fitted with a stay,
- baby cot fitted with a "Top Tether" upper strap or a stay.
For the securing of the "Top Tether" upper strap, refer to the "ISoFIX Mountings" section.
X:
seat which is not suitable for the installation of an ISOFIX child seat or cot of the weight group indicated.
X IL-SU
Remove and stow the head restraint before installing a child seat with a backrest on a passenger seat. Refit the head restraint once the child seat has been removed.
IUF
IL-SU
Child safety
advice on child seats
The incorrect installation of a child seat in a vehicle compromises the child's protection in the event of an accident.
Ensure that there is no seat belt or seat belt buckle under the child seat, as this could destabilise it.
Remember to fasten the seat belts or the child seat harnesses keeping the slack relative to the child's body to a minimum, even for short journeys.
When installing a child seat using the seat belt, ensure that the seat belt is tightened correctly on the child seat and that it secures the child seat firmly on the seat of your vehicle. If your passenger seat is adjustable, move it forwards if necessary.
At rear seating positions, always leave sufficient space between the front seat and:
- a "rearward facing" child seat,
- the child's feet for a child seat fitted
"forward facing".
To do this, move the front seat forwards and, if necessary, move its backrest into the upright position.
For optimum installation of the "forwardfacing" child seat, ensure that the back of the child seat is as close as possible to the backrest of the vehicle's seat, in contact if possible.
You mst remove the head restraint before installing a child seat with backrest to a passenger seat.
Ensure that the head restraint is stored or attached securely to prevent it from being thrown around the vehicle in the event of sharp braking. Refit the head restraint when the child seat is removed.
Children at the front
The legislation on carrying children on the front passenger seat is specific to each country. Refer to the legislation in force in your country.
Deactivate the passenger airbag when a
"rearward-facing" child seat is installed on the front seat.
Otherwise, the child would risk being seriously injured or killed if the airbag were to inflate.
Installing a booster seat
The chest part of the seat belt must be positioned on the child's shoulder without touching the neck.
Ensure that the lap part of the seat belt passes correctly over the child's thighs.
CITRoËn recommends the use of a booster seat which has a back, fitted with a seat belt guide at shoulder level.
as a safety precaution, do not leave:
- a child or children alone and unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with the windows closed,
- the keys within reach of children inside the vehicle.
To prevent accidental opening of the doors and rear windows, use the "Child lock".
Take care not to open the rear windows by more than one third.
To protect young children from the rays of the sun, fit side blinds on the rear windows.
7
97
Child safety
Electric child lock
Remote control system to prevent opening of the rear doors using their interior controls and use of the rear electric windows*.
The control is located:
- either on the dashboard, driver's side, for versions without rear electric windows,
- or on the driver's door, with the electric window controls, for versions fitted with rear electric windows.
Activation
F Press this button.
The indicator lamp on the button comes on, accompanied by a message in the multifunction screen.
This indicator lamp remains on until the child lock is deactivated.
Deactivation
F Press the button again.
The indicator lamp on the button goes off, accompanied by a message in the multifunction screen.
This indicator lamp remains off until the child lock is activated.
This system is independent and in no circumstances does it take the place of the central locking control.
Check the status of the child lock each time you switch on the ignition.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
98
* according to version.
Safety
direction indicators
Selection of the left or right direction indicators to signal a change of direction of the vehicle.
Hazard warning lamps
A visual warning by means of the direction indicators to alert other road users to a vehicle breakdown, towing or accident.
Automatic operation of hazard warning lamps
When braking in an emergency, depending on the deceleration, the hazard warning lamps come on automatically.
They switch off automatically the first time you accelerate.
F You can also switch them off by pressing the button.
F Left: lower the lighting stalk beyond the point of resistance.
F Right: raise the lighting stalk beyond the point of resistance.
Three flashes of the direction indicators
F Press briefly upwards or downwards, without going beyond the point of resistance; the direction indicators will flash 3 times.
F Press this button, the direction indicators flash.
They can operate with the ignition off.
8
99
100
Safety
Horn
Audible warning to alert other road users to an imminent danger.
Emergency or assistance call
F Press one of the spokes of the steering wheel.
This system allows you to make an emergency or assistance call to the emergency services or to the dedicated CITRoËn service.
For more information on the use of this function, refer to the "audio and telematics" section.
Safety
Tyre under-inflation detection
System which automatically checks the pressure of the tyres while driving.
The system monitors the pressures on the four tyres, once the vehicle is moving.
It compares the information given by the four wheel speed sensors with reference values, which must be reinitialised every time the tyre pressures are adjusted or a wheel changed .
The system triggers an alert as soon as it detects a drop in the inflation pressure of one or more tyres.
The under-inflation detection system does not replace the vigilance or the responsibility of the driver.
This system does not avoid the need to check the tyre pressures (including the spare wheel) every month as well as before a long journey.
Driving with under-inflated tyres impairs road holding, extends braking distances and causes premature tyre wear, particularly under arduous condition
(high loading, high speed, long journey).
The inflation pressures defined for your vehicle can be found on the tyre pressure label.
See the "Identification markings" section.
Tyre pressures should be checked when the tyres are "cold" (vehicle stopped for 1 hour or after a journey of less than 6 miles (10 km) at moderate speeds).
Otherwise (when hot), add 0.3 bar to the pressures shown on the label.
8
Driving with under-inflated tyres increases fuel consumption.
101
102
Safety
Under-inflation alert
This is given by fixed illumination of this warning lamp, accompanied by an audible signal and, depending on equipment, the display of a message.
F Reduce speed immediately, avoid excessive steering movements and sudden braking
F Stop the vehicle as soon as it is safe to do so.
F In the event of a puncture, use the temporary puncture repair kit or the spare wheel (depending on equipment), or
F if you have a compressor, such as the one in the temporary puncture repair kit, check the pressures of the four tyres when cold, or
F if it is not possible to make this check immediately, drive carefully at reduced speed.
The loss of pressure detected does not always cause visible bulging of the tyre.
Do not satisfy yourself with just a visual check.
The alert is maintained until the system is reinitialised.
Reinitialisation
It is necessary to reinitialise the system every time one or more tyre pressure is adjusted, and after changing one or more wheels.
a label attached to the middle pillar, left hand side, gives a reminder of this.
before reinitialising the system, ensure that the pressures of the four tyres are correct for the use of the vehicle and in line with the recommendations on the tyre pressure label.
The under-inflation detection system does not give a warning if a pressure is incorrect at the time of reinitialisation.
Safety
Reinitialisation of the system must be done with the ignition on and the vehicle stationary, in the vehicle configuration menu.
Monochrome screen A
F Press the MENU button for access to the main menu.
F Press the " 5 " or " 6 " button to select the menu Veh config , then confirm by pressing the OK button.
F Press the " 5 " or " 6 " button to select the
" Reinit inflat ", menu, then confirm by pressing the OK button.
a message is displayed to confirm the instruction.
F Confirm by pressing the OK button.
Monochrome screen C
F Press the MENU button for access to the main menu.
F Press the " 5 " or " 6 " button to select the menu, " Personalisation-configuration " then confirm by pressing the OK button.
F Press the " 5 " or " 6 " button to select the
" Define vehicle parameters " menu, then confirm by pressing the OK button.
F Press the " 5 " or " 6 " button to select the " Tyre pressures " menu, then the
" Reinitialisation " menu, then confirming by pressing the OK button.
a message confirms the reinitialisation.
Colour screen
F Press the " SETUP " button for access to the configuration menu.
F Select the " Vehicle parameters " menu, then confirm.
F Select " Driving assistance ", then confirm.
F Select " Initialisation of under-inflation ", then confirm.
a message is displayed to confirm the reinitialisation instruction.
F Select " Yes " or " No ", then confirm.
a message confirms the reinitialisation.
8
The new pressure settings registered are considered to be reference values by the system.
103
104
Safety
Operating fault
The under-inflation alert is only dependable if the system has been reinitialised with all four tyres inflated to the correct pressures.
Snow chains
The system does not have to be reinitialised after fitting or removing snow chains.
The flashing and then fixed illumination of the under-inflation warning lamp accompanied by illumination of the Service warning lamp indicates a fault with the system.
In this case, under-inflation monitoring of the tyres is no longer assured.
Have the system checked by a CITRoËn dealer or a qualified workshop.
before doing anything to the system, the pressures of the four tyres must be checked and the system reinitialised.
Safety
braking assistance systems
Group of supplementary systems which help you to obtain optimum braking in complete
Operating fault
safety in emergency situations:
- anti-lock braking system (abS),
- electronic brake force distribution (EbFd),
If this warning lamp comes on, accompanied by an audible signal
- emergency braking assistance (Eba).
and a message in the screen, it indicates a malfunction of the antilock braking system which could result in loss of control of the vehicle when braking.
Anti-lock braking system and electronic brake force distribution
Linked systems which improve the stability and manoeuvrability of your vehicle when braking, in particular on poor or slippery surfaces.
If this warning lamp comes on, together with the
STOP and ABS warning lamps, accompanied by an audible signal and a message in the screen, it indicates a malfunction of the electronic brake force distribution which could result in loss of control of the vehicle when braking.
Activation
The anti-lock braking system comes into operation automatically when there is a risk of wheel lock.
normal operation of the abS may make itself felt by slight vibration of the brake pedal.
You must stop as soon as it is safe to do so.
In either case, contact a CITRoËn dealer or a qualified workshop.
When replacing wheels (tyres and rims), ensure that they conform to the manufacturer's recommendations.
When braking in an emergency, press very firmly without releasing the pressure.
Emergency braking assistance
System which, in an emergency, enables you to obtain the optimum braking pressure more quickly, thus reducing the stopping distance.
Activation
It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in the resistance of the pedal and an increase in braking efficiency.
When braking in an emergency, press firmly without releasing the pressure.
8
105
106
Safety
Trajectory control systems
Anti-slip regulation (ASR) and dynamic stability control (DSC)
The anti-slip regulation (also known as traction control) optimises traction to prevent skidding of the wheels, by acting on the brakes of the driving wheels and on the engine.
The electronic stability control acts on the brake of one or more wheels and on the engine to keep the vehicle on the trajectory required by the driver, within the limits of the laws of physics.
Activation
These systems are activated automatically each time the vehicle is started.
They come into operation in the event of a grip or trajectory problem.
Deactivation
In exceptional conditions (starting a vehicle which is bogged down, stuck in snow, on soft ground...), if you are unable to make progress, it may be advisable to temporarily deactivate these systems, so that the wheels can spin freely and allow the vehicle to move.
F Press the "ESP OFF" button, located near the steering wheel.
This is indicated by flashing of this warning lamp in the instrument panel.
If this warning lamp comes on in the instrument panel and the indicator lamp in the button comes on, this indicates that these systems are deactivated.
It is recommended that the systems be reactivated as soon as possible.
Reactivation
These systems are reactivated automatically each time the ignition is switched back on or from 30 mph (50 km/h).
F Press the "ESP OFF" button again to reactivate them manually.
Operating fault
If this warning lamp comes on, accompanied by an audible signal and a message in the screen, this indicates a fault with these systems.
Have it checked by a CITRoËn dealer or a qualified workshop.
The trajectory control systems offer increased safety in normal driving, but this should not encourage the driver to take extra risks or drive at high speed.
The correct functioning of these systems is assured provided that manufacturer's recommendations are observed on:
- wheels (tyres and rims),
- braking components,
- electronic components,
- assembly and repair procedures.
after an impact, have these systems checked by a CITRoËn dealer or a qualified workshop.
Safety
Seat belts
Front seat belts
The front seat belts are fitted with a pretensioning and force limiting system.
This system improves safety in the front seats in the event of a front or side impact. depending on the severity of the impact, the pretensioning system instantly tightens the seat belts against the body of the occupants.
The pretensioning seat belts are active when the ignition is on.
The force limiter reduces the pressure of the seat belt on the chest of the occupant, so improving their protection.
Fastening
F Pull the strap, then insert the tongue in the buckle.
F Check that the seat belt is fastened correctly by pulling the strap.
Unfastening
F Press the red button on the buckle.
F Guide the seat belt as it is reeled in.
Seat belt not fastened / unfastened warning lamp
When the ignition is switched on, this warning lamp comes on in the instrument panel, if the driver and/or the front passenger has not fastened their seat belt.
From approximately 12 mph (20 km/h) this warning lamp flashes for two minutes accompanied by an audible signal of increasing volume. Once these two minutes have elapsed, this warning lamp remains on until the driver and/ or the front passenger fastens their seat belt.
Rear seat belts
The rear seats are each fitted with a three-point inertia reel seat belt.
Fastening
F Pull the strap, then insert the tongue in the buckle.
F Check that the seat belt is fastened correctly by pulling the strap.
Unfastening
F Press the red button on the buckle.
F Guide the seat belt as it is reeled in.
8
107
108
Safety
The driver must ensure that passengers use the seat belts correctly and that they are all restrained securely before setting off.
Wherever you are seated in the vehicle, always fasten your seat belt, even for short journeys.
do not interchange the seat belt buckles as they will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the length of the strap to your size. The seat belt is stowed automatically when not in use.
before and after use, ensure that the seat belt is reeled in correctly.
The lower part of the strap must be positioned as low as possible on the pelvis.
The upper part must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation in the event of a collision, emergency braking or if the vehicle rolls over. You can release the device by pulling the strap firmly and then releasing it so that it reels in slightly.
In order to be effective, a seat belt must:
- be tightened as close to the body as possible,
- be pulled in front of you with a smooth movement, checking that it does not twist,
- be used to restrain only one person,
- not bear any trace of cuts or fraying,
- not be converted or modified to avoid affecting its performance.
In accordance with current safety regulations, for all repairs on your vehicle's seat belts, go to a qualified workshop with the skills and equipment needed, which a
CITRoËn dealer is able to provide.
Have your seat belts checked regularly by a CITROËN dealer or a qualified workshop, particularly if the straps show signs of damage.
Clean the seat belt straps with soapy water or a textile cleaning product, sold by
CITRoËn dealers.
after folding or moving a seat or rear bench seat, ensure that the seat belt is positioned and reeled in correctly.
Recommendations for children
Use a suitable child seat if the passenger is less than 12 years old or shorter than one and a half metres.
never use the same seat belt to secure more than one person.
Never allow a child to travel on your lap.
For more information, refer to the "Child seats" section.
In the event of an impact
Depending on the nature and seriousness of the impact , the pretensioning device may be deployed before and independently of the airbags. deployment of the pretensioners is accompanied by a slight discharge of harmless smoke and a noise, due to the activation of the pyrotechnic cartridge incorporated in the system.
In all cases, the airbag warning lamp comes on.
Following an impact, have the seat belts system checked, and if necessary replaced, by a CITRoËn dealer or a qualified workshop.
Safety
airbags
System designed to contribute towards improving the safety of the occupants (with the exception of the rear centre passenger) in the event of violent collisions. The airbags supplement the action of the force-limiting seat belts (with the exception of the centre rear passenger).
If a collision occurs, the electronic detectors record and analyse the front and side impacts sustained in the impact detection zones:
- in the case of a serious impact, the airbags are deployed instantly and contribute towards better protection of the occupants of the vehicle (with the exception of the rear centre passenger); immediately after the impact, the airbags deflate rapidly so that they do not hinder visibility or the exit of the occupants,
- in the case of a minor or rear impact or in certain roll-over conditions, the airbags may not be deployed; the seat belt alone contributes towards ensuring your protection in these situations.
The airbags do not operate when the ignition is switched off.
This equipment will only deploy once.
If a second impact occurs (during the same or a subsequent accident), the airbag will not be deployed again.
Impact detection zones
A.
Front impact zone.
B.
Side impact zone.
deployment of one or more of the airbags is accompanied by a slight emission of smoke and a noise, due to the activation of the pyrotechnic cartridge incorporated in the system.
This smoke is not harmful, but sensitive individuals may experience slight irritation.
The noise of detonation related to the deployment of one or more airbags may result in a slight loss of hearing for a short time.
Front airbags
System which protects the driver and front passenger in the event of a serious front impact in order to limit the risk of injury to the head and chest.
The driver's airbag is fitted in the centre of the steering wheel; the front passenger's airbag is fitted in the dashboard above the glove box.
Deployment
The airbags are deployed, except the passenger's front airbag if it is deactivated, in the event of a serious front impact applied to all or part of the front impact zone A , in the longitudinal centreline of the vehicle on a horizontal plane and directed from the front to the rear of the vehicle.
The front airbag inflates between the head-thorax of the front occupant of the vehicle and the dashboard to cushion their forward movement.
8
109
110
Safety
Deactivation
only the passenger's front airbag can be deactivated:
F with the ignition off , insert the key in the passenger airbag deactivation switch,
F turn it to the "OFF" position,
F then, remove the key keeping the switch in the new position.
To assure the safety of your child, the passenger's front airbag must be deactivated when you install a
"rearward facing" child seat on the front passenger seat.
Otherwise, the child would risk being seriously injured or killed if the airbag were deployed.
Reactivation
When you remove a child seat that has been fitted "rearward facing", with the ignition off, turn switch to the
"ON" position to re-activate the airbag and so assure the safety of your front passenger in the event of an impact.
Operating fault
If this warning lamp comes on in the instrument panel, accompanied by an audible warning and a message in the multifunction screen, contact a
CITROËN dealer or qualified workshop without delay to have the system checked. The airbags may no longer be deployed in the event of a serious impact.
If this warning lamp flashes, contact a
CITROËN dealer or a qualified workshop without delay. The passenger's front airbag may no longer be deployed in the event of a serious impact.
If at least one of the two airbag warning lamps come on continuously, do not install a child seat on the front passenger seat.
Have it checked by a CITRoËn dealer or a qualified workshop.
This warning lamp comes on in the instrument panel when the ignition is on and until the airbag is re-activated.
Lateral airbags
System which protects the driver and front passenger in the event of a serious side impact in order to limit the risk of injury to the chest, between the hip and the shoulder.
Each lateral airbag is fitted in the seat backrest frame, door side.
Impact detection zones
Deployment
a lateral airbag is deployed unilaterally in the event of a serious side impact applied to all or part of the side impact zone B , perpendicular to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside towards the inside of the vehicle.
The lateral airbag inflates between the hip and shoulder of the front occupant of the vehicle and the corresponding door trim panel.
A.
Front impact zone.
B.
Side impact zone.
Safety
Curtain airbags
System which contributes towards improving the protection of the driver and passengers (with the exception of the rear centre passenger) in the event of a serious side impact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and the upper passenger compartment area.
Deployment
The curtain airbag is deployed at the same time as the corresponding lateral airbag in the event of a serious side impact applied to all or part of the side impact zone B , perpendicular to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside towards the inside of the vehicle.
The curtain airbag inflates between the front or rear occupant of the vehicle and the windows.
8
111
112
Safety
For the airbags to be fully effective, observe the following safety rules:
Sit in a normal upright position.
Wear a correctly adjusted seat belt.
Do not leave anything between the occupants and the airbags (a child, pet, object...). This could hamper the operation of the airbags or injure the occupants.
after an accident or if the vehicle has been stolen or broken into, have the airbag systems checked.
All work on the airbag system must be carried out by a CITRoËn dealer or a qualified workshop.
Front airbags
Do not drive holding the steering wheel by its spokes or resting your hands on the centre part of the wheel.
Passengers must not place their feet on the dashboard.
do not smoke as deployment of the airbags can cause burns or the risk of injury from a cigarette or pipe.
Never remove or pierce the steering wheel or hit it violently.
Do not fit or attach anything to the steering wheel or dashboard, this could cause injuries with deployment of the airbags.
Lateral airbags
Use only approved covers on the seats, compatible with the deployment the lateral airbags.
For information on the range of seat covers suitable for your vehicle, you can contact a
CITRoËn dealer.
Refer to the "accessories" section.
do not fix or attach anything to the seat backs (clothing...). This could cause injury to the chest or arms if the lateral airbag is deployed.
Do not sit with the upper part of the body any nearer to the door than necessary.
Even if all of the precautions mentioned are observed, a risk of injury or of minor burns to the head, chest or arms when an airbag is deployed cannot be ruled out. The bag inflates almost instantly (within a few milliseconds) then deflates within the same time discharging the hot gas via openings provided for this purpose.
Curtain airbags
do not fix or attach anything to the roof. This could cause injury to the head if the curtain airbag is deployed.
If fitted on your vehicle, do not remove the grab handles installed on the roof, they play a part in securing the curtain airbags.
Parking brake 6-speed manual gearbox
Engaging 5
th
or 6
th
gear
F Move the lever fully to the right to engage
5 th or 6 th gear.
Engaging reverse gear
Driving
Applying
F Pull the parking brake lever fully up to immobilise your vehicle.
Releasing
F Pull the parking brake lever gently, press the release button then lower the lever fully.
When the vehicle is being driven, if this warning lamp and the
STOP
warning lamp come on, accompanied by an audible signal and a message in the multifunction screen, this indicates that the parking brake is still on or has not been properly released.
When parking on a slope, direct your wheels against the pavement, apply the parking brake and engage a gear.
Failure to follow this advice may cause permanent damage to the gearbox
(engagement of 3 rd or 4 th gear by mistake).
F Raise the ring under the knob and move the gear lever to the left then forwards.
Only engage reverse gear when the vehicle is stationary with the engine at idle.
9 as a safety precaution and to facilitate starting of the engine:
- always select neutral,
- press the clutch pedal.
113
114
Driving
Electronic gearbox
Five or six-speed electronically controlled gearbox which offers a choice between the comfort of automated operation or the pleasure of manual gear changing.
Two driving modes are offered:
- automated mode for automatic control of the gears by the gearbox, without any action by the driver,
- manual mode for the sequential changing of the gears by the driver, using the gear lever or the steering mounted control paddles.
In automated mode, you can temporarily take control of gear changes at any time, using the steering mounted control paddles.
Gear lever Steering mounted controls
R.
Reverse.
F With your foot on the brake, move the lever forwards to select this position.
N.
neutral.
F With your foot on the brake, select this position to start the engine.
A.
automated mode.
F Move the lever backwards to select this mode.
M + / -.
Manual mode with sequential gear changing.
F Move the lever backwards, then to the left to select this mode, then:
- push forwards to change up a gear,
- or push backwards to change down a gear.
+.
Paddle to the right of the steering wheel for changing up.
F Press the back of the steering mounted "+" paddle to change up a gear.
-.
Paddle to the left of the steering wheel for changing down.
F Press the back of the steering mounted "-" paddle to change down a gear.
The steering mounted paddles do not allow neutral to be selected, reverse gear to be engaged or disengaged, or the driving mode to be changed.
Driving
Display in the instrument panel Moving off
F Select position N .
F Press the brake pedal fully.
F Start the engine.
You must keep your foot on the brake pedal while starting the engine.
N appears in the instrument panel.
F Accelerate away.
do not press the brake and clutch pedals simultaneously. This can cause rapid clutch wear.
Gear lever positions
N.
neutral
R.
Reverse
1 2 3 4 5 / 6.
Gears in manual mode.
AUTO.
This comes on when automated mode is selected. It goes off when changing to manual mode.
F
Place your foot on the brake when this warning lamp flashes
(e.g.: starting the engine).
N flashes in the instrument panel screen if the gear lever is not in position N
when starting.
F Select automated mode (position A ), manual mode (position M ) or reverse
(position R ).
AUTO and 1 , 1 or R appear in the instrument panel.
F Release the parking brake.
F Progressively take your foot off the brake pedal.
depending on the type of electronic gearbox, the vehicle may move off on its own (refer to the paragraph "Creep function").
Creep function
(depending on equipment)
This function allows the vehicle to be manoeuvred more easily at low speeds (when parking, in traffic jams...).
With the gear lever in position A , M or R , the vehicle moves as soon as you take your foot off the brake pedal
, at low speed and with the engine at idle.
9 do not leave children unsupervised inside the vehicle when the engine is running.
The creep function may be temporarily unavailable if the clutch temperature is too high or the slope too steep.
115
116
Driving
Automated mode
F Select position A .
AUTO and the gear engaged appear in the instrument panel.
The gearbox then operates in auto-adaptive mode, without any action on the part of the driver. It continuously selects the most suitable gear taking account of:
- optimisation of fuel consumption,
- driving style,
- road conditions,
- vehicle load.
For optimum acceleration, when overtaking another vehicle for example, press the accelerator pedal fully down, beyond the point of resistance.
Temporary control of gear changing
You can temporarily take over control of gear changes using the steering mounted "+" and "-" control paddles: if the engine speed allows, the gear change is carried out.
This function allows you to anticipate certain situations such as overtaking another vehicle or approaching a bend.
After a few moments without any action on the paddles, the gearbox resumes control of gear changing automatically.
Manual mode
F Select position M .
The gears engaged appear in succession in the instrument panel.
The gear change requests are only carried out if the engine speed permits.
It is not necessary to release the accelerator pedal during gear changes.
When braking or slowing down, the gearbox changes down automatically so that the vehicle picks up in the right gear.
Under full acceleration, the change up will not take place unless the driver operates the gear lever or steering mounted control paddle
(unless the engine is close to its maximum speed).
You can change mode at any time by moving the gear lever from A to M or the other way round.
never select neutral (position N
) when moving.
You can change mode at any time by moving the gear lever from A to M or the other way round.
never select neutral (position N
) when moving.
Driving
Reverse
To engage reverse, the vehicle must be immobilised with your foot on the brake.
F Select position R .
There is an audible signal on engagement of reverse.
At low speed, if reverse gear is requested, the N
warning lamp flashes and the gearbox goes into neutral automatically.
To engage reverse, put the gear lever into position N , then to position R .
Stopping the vehicle
Before switching off the engine:
- change to position N to be in neutral, or
- leave the vehicle in gear; in this case the vehicle cannot be moved.
For all parking situations, you must apply the parking brake to immobilise the vehicle.
When immobilising the vehicle with the engine running, you must put the gear lever into neutral (position N ).
before doing anything under the bonnet, ensure that the gear lever is in neutral (position N ) and that the parking brake is applied.
Reinitialisation
(5-speed electronic gearbox)
Following disconnection of the battery, it is necessary to reinitialise the gearbox.
F Switch on the ignition.
AUTO and - appear in the instrument panel.
F Select position N .
F Press the brake pedal.
F Wait for around 30 seconds until N or a gear appears in the instrument panel.
F Move the gear lever to position A , then to position N .
F With your foot still on the brake pedal, start the engine.
The gearbox is operational again.
In exceptional circumstances, the gearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.
AUTO and - appear in the instrument panel.
Follow the procedure described above.
Operating fault
With the ignition on, if this warning lamp comes on and AUTO flashes, accompanied by an audible signal and a message in the multifunction screen, this indicates a gearbox fault.
Have it checked by a CITRoËn dealer or a qualified workshop.
9
117
118
Driving
automatic gearbox
Four-speed automatic gearbox which offers a choice between the comfort of fully automatic operation, enhanced by sport and snow programmes, or manual gear changing.
There are therefore four driving modes:
- automatic operation for electronic management of the gears by the gearbox,
- sport programme for a more dynamic style of driving,
- snow
programme to improve driving when traction is poor,
- sequential operation for manual changing of the gears by the driver.
Gear lever
Gear selection gate
1.
Gear lever.
2.
button (sport) .
3.
button " (snow) .
Displays in the instrument panel
P.
Park.
- Immobilisation of the vehicle, parking brake on or off.
- Starting the engine.
R.
Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.
N.
neutral.
- Immobilisation of the vehicle, parking brake on.
- Starting the engine.
D.
automatic operation.
M + / -.
Manual operation with sequential changing of the four gears.
F Push forwards to change up through the gears.
or
F Pull backwards to change down through the gears.
When you move the lever in the gate to select a position, the corresponding indicator is displayed in the instrument panel.
P.
Park
R.
Reverse
N.
neutral
D.
drive (automatic driving)
S.
Sport programme
T .
Snow programme
1 2 3 4.
Gears engaged during manual operation
-.
Invalid value during manual operation
Foot on brake
F Press the brake pedal when this indicator lamp is displayed in the instrument panel (e.g.: starting the engine).
Driving
Moving off
F apply the parking brake.
F Select position P or N .
F Start the engine.
If this procedure is not followed, there is an audible signal, accompanied by the display of an warning message.
F With the engine running, press the brake pedal.
F Release the parking brake.
F Select position R , D or M .
F Gradually release the brake pedal.
The vehicle moves off immediately.
If position N is selected inadvertently while driving, allow the engine to return to idle then select position D to accelerate.
When the engine is running at idle, with the brakes released, if position R , D or
M is selected, the vehicle moves even without the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision.
When carrying out maintenance with the engine running, apply the parking brake and select position P .
Automatic operation
F Select position D for automatic changing of the four gears.
The gearbox then operates in auto-adaptive mode, without any intervention on the part of the driver. It continuously selects the most suitable gear according to the style of driving, the profile of the road and the load in the vehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal down fully (kick down). The gearbox changes down automatically or maintains the gear selected until the maximum engine speed is reached.
On braking, the gearbox changes down automatically to provide efficient engine braking.
If you release the accelerator sharply, the gearbox will not change to a higher gear for safety reasons.
Sport and snow programmes
These two special programmes supplement the automatic operation in very specific conditions of use.
Sport programme "S"
F Press button "S" , after starting the engine.
The gearbox automatically favours a dynamic style of driving.
S appears in the instrument panel.
Snow programme "
T
"
F Press button " T ", after starting the engine.
The gearbox adapts to driving on slippery roads.
This programme improves starting and drive when traction is poor.
9 never select position N
while the vehicle is moving.
never select positions P or R unless the vehicle is completely stationary.
T appears in the instrument panel.
119
120
Driving
Return to automatic operation
F at any time, press the button selected again to quit the programme engaged and return to auto-adaptive mode.
Manual operation
F Select position M for sequential changing of the four gears.
F Push the lever towards the
+ sign to change up a gear.
F Pull the lever towards the
sign to change down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speed permit; otherwise, the gearbox will operate temporarily in automatic mode.
Invalid value during manual operation
This symbol is displayed if a gear is not engaged correctly (selector between two positions).
D disappears and the gears engaged appear in succession in the instrument panel.
If the engine speed is too low or too high, the gear selected flashes for a few seconds, then the actual gear engaged is displayed.
It is possible to change from position D
(automatic) to position M (manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox selects gear
M1 automatically.
The sport and snow programmes do not operate in manual mode.
Driving
Stopping the vehicle
Before switching off the engine, you can engage position P or N to place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle.
If the lever is not in position P
, when the driver's door is opened or approximately
45 seconds after the ignition is switched off, a warning message appears in the screen.
F Return the lever to position P
; the message disappears.
Operating fault
When the ignition is on, the lighting of this warning lamp, accompanied by an audible signal and a message in the multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel a substantial knock when changing from
P to R and from N to R
. This will not cause any damage to the gearbox.
do not exceed 60 mph (100 km/h), local speed restrictions permitting.
Contact a CITRoËn dealer or a qualified workshop as soon as possible.
There is a risk of damage to the gearbox:
- if you press the accelerator and brake pedals at the same time,
- if you force the movement of the gear lever from the P position to another position when the battery is flat.
To reduce fuel consumption when at a prolonged standstill with the engine running (traffic jam...), put the gear lever in the N position and apply the parking brake.
If the ambient temperature is below
-23°C, the engine should be left running at idle for four minutes, in order to ensure the correct operation and durability of the engine and gearbox.
9
When traversing a flooded road or a ford, drive at walking pace.
121
Driving
Gear efficiency indicator*
System which reduces fuel consumption by advising the driver to change up.
With an electronic or automatic gearbox, the system is only active in manual mode.
Example:
- You are in third gear.
- You press the accelerator pedal moderately.
- The system may suggest that you engage a higher gear, if appropriate.
Operation
The system intervenes only when driving economically.
depending on the driving situation and your vehicle's equipment, the system may advise you to skip one or more gears. You can follow this instruction without engaging the intermediate gears.
The gear engagement recommendations must not be considered compulsory. In fact, the configuration of the road, the amount of traffic and safety remain determining factors when choosing the best gear. Therefore, the driver remains responsible for deciding whether or not to follow the advice given by the system.
This function cannot be deactivated.
The information appears in the instrument panel in the form of an arrow accompanied by the suggested gear.
In the case of driving which makes particular demands on the performance of the engine (firm pressure on the accelerator pedal, for example, when overtaking...), the system will not recommend a gear change.
The system never suggests:
- engaging first gear,
- engaging reverse gear,
- engaging a lower gear.
122
* depending on engine.
Driving
Stop & Start
The Stop & Start system puts the engine temporarily into standby - SToP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Perfect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Operation
Going into engine STOP mode
The "ECO"
warning lamp comes on in the instrument panel and the engine goes into standby:
- with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear lever into neutral, and you release the clutch pedal.
- with a 5 or 6-speed electronic gearbox , when stationary or at speeds below 5 mph
(8 km/h) (depending on version), when you press the brake pedal or put the gear lever in position N .
For your comfort, during parking manoeuvres, SToP mode is not available for a few seconds after coming out of reverse gear.
SToP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...
Never refuel with the engine in STOP mode; you must switch off the ignition with the key.
Special cases: STOP mode not available
STOP mode is not invoked when:
- the driver's door is open,
- the driver's seat belt is not fastened,
- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine start using the key,
- the engine is needed to maintain a comfortable temperature in the passenger compartment,
- demisting is active,
- some special conditions (battery charge, engine temperature, braking assistance, ambient temperature...) where the engine is needed to assure control of a system.
9 a time counter calculates the sum of the periods in SToP mode during a journey. It rests itself to zero every time the ignition is switched on with the key.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is perfectly normal.
123
124
Driving
Deactivation
Going into engine START mode
The "ECO"
warning lamp goes off and the engine starts:
- with a manual gearbox
, when you depress the clutch pedal,
- with a 5-speed or 6-speed electronic gearbox :
● gear lever in position
A or M
, when you release the brake pedal,
● or gear lever in position
N and the brake pedal released, when you move the gear lever to position A or M ,
● or when you engage reverse gear.
Special cases: START invoked automatically
For reasons of safety and for your comfort,
START mode is invoked automatically when:
- you open the driver's door,
- you unfasten the driver's seat belt,
- the speed of the vehicle exceeds 7 mph
(11 km/h) with the electronic gearbox system,
- some special conditions (battery charge, engine temperature, braking assistance, ambient temperature...) where the engine is needed for control of a system.
at any time, press the "ECO OFF"
switch to deactivate the system.
This is confirmed by the switch warning lamp coming on accompanied by a message in the screen.
The "ECO"
warning lamp flashes for a few seconds, then goes off.
If the system has been deactivated in SToP mode, the engine restarts immediately.
This operation is perfectly normal.
With a manual gearbox in SToP mode, if you engage a gear without fully depressing the clutch pedal, a message is displayed asking you to fully depress the clutch pedal so that the engine can restart.
Driving
Operating fault Maintenance Reactivation
Press the "ECO OFF"
switch again.
The system is active again; this is confirmed by the switch warning lamp going off, accompanied by a message in the screen.
The system is reactivated automatically at every new start using the key.
In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes then comes on continuously.
Have it checked by a CITRoËn dealer or a qualified workshop.
In the event of a fault in SToP mode, the vehicle may stall. all of the instrument panel warning lamps come on. It is then necessary to switch off the ignition and start the engine again using the key.
before doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury resulting from automatic operation of
STaRT mode.
This system requires a battery with a special specification and technology (reference numbers available from a CITRoËn dealer or a qualified workshop).
Fitting a battery not listed by
CITRoËn introduces the risk of malfunction of the system.
The Stop & Start system makes use of advanced technology. All work on this type of battery must be done by a CITRoËn dealer or a qualified workshop.
9
125
126
Driving
Hill start assist
System which holds your vehicle temporarily
(approximately 2 seconds) when starting on a slope, the time it takes to move your foot from the brake pedal to the accelerator pedal.
This function is only active when:
- the vehicle is completely stationary, with your foot on the brake pedal,
- certain conditions on a slope are met,
- with the driver’s door closed.
The hill start assist function cannot be deactivated.
Operation
On an ascending slope, with the vehicle stationary, the vehicle is held momentarily when you release the brake pedal:
- provided you are in automated mode
(position A ) or in manual mode (position M ) on an electronic gearbox.
On a descending slope, with the vehicle stationary and reverse gear engaged, the vehicle is held momentarily when you release the brake pedal.
Operating fault
Do not leave the vehicle while it is being held in the hill start assist phase.
If you need to leave the vehicle with the engine running, manually apply the parking brake then ensure that the parking brake warning lamp is on (not flashing) in the instrument panel.
If a malfunction of the system occurs, these warning lamps come on. Contact a CITROËN dealer or a qualified workshop to have the system checked.
Driving
Speed limiter
System which prevents the vehicle from exceeding the speed programmed by the driver.
When the programmed speed limit is reached, pressing the accelerator pedal in the normal manner no longer has any effect.
The speed limiter is switched on manually: it requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is switched off by manual operation of the control.
The programmed speed can be exceeded temporarily by pressing the accelerator firmly.
To return to the programmed speed, simply slow down to a speed below the programmed speed.
Steering mounted controls Displays in the instrument panel
The controls of this system are grouped together on stalk A .
1.
Speed limiter mode selection thumb wheel.
2.
Value decrease button.
3.
Value increase button.
4.
Speed limiter on / off button.
The programmed information is grouped together in the instrument panel screen.
5.
Speed limiter on / off indication.
6.
Speed limiter mode selection indication.
7.
Programmed speed value.
The programmed speed remains in the memory when the ignition is switched off.
9
The speed limiter cannot, in any circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance on the part of the driver.
127
Driving
Programming
F Turn thumb wheel
1 to the "LIMIT" position: the speed limiter mode is selected but is not switched on in order to set the speed.
F Set the speed value by pressing button 2 or 3
(e.g.: 55 mph
(90 km/h)).
on (PaUSE).
You do not have to switch the speed limiter
You can then change the programmed speed using buttons 2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
F Switch the speed limiter on by pressing button
4 .
F Switch the speed limiter off by pressing button
4 : the display confirms that it has been switched off (PAUSE).
F Switch the speed limiter back on by pressing button
4 again.
128
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not have any effect unless you press the pedal firmly past the point of resistance .
The speed limiter is deactivated temporarily and the programmed speed, which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional deceleration of the vehicle, automatically cancels the flashing of the programmed speed.
Leaving limiter mode
F Turn thumb wheel
1 to the "0" position: the speed limiter mode is deselected. The display returns to the distance recorder.
Operating fault
In the event of a speed limiter fault, the speed is cleared resulting in flashing of the dashes.
Have it checked by a CITRoËn dealer or a qualified workshop.
on a steep descent or in the event of sharp acceleration, the speed limiter will not be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:
- ensure that the mat is secured correctly,
- do not fit one mat on top of another.
Driving
Cruise control
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control is switched on manually: it requires a minimum vehicle speed of 25 mph
(40 km/h), as well as the engagement of:
- fourth gear on a manual gearbox,
- second gear on a or automatic or electronic gearbox, in sequential mode,
Steering mounted controls Displays in the instrument panel
position D on an automatic gearbox.
The cruise control is switched off manually or by pressing the brake or clutch pedal or on triggering of the ESP system for safety reasons.
The controls of this system are grouped together on stalk A .
1.
Cruise control mode selection thumb wheel.
2.
Value decrease button.
3.
Value increase button.
4.
Cruise control off/resume button.
The programmed information is grouped together in the instrument panel screen.
5.
Cruise control off/resume indication.
6.
Cruise control mode selection indication.
7.
Programmed speed value.
9
It is possible to exceed the programmed speed temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply release the accelerator pedal.
Switching off the ignition cancels any programmed speed value.
The cruise control cannot, in any circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance on the part of the driver.
129
130
Driving
Programming
F Turn thumb wheel
1 to the "CRUISE" position: the cruise control mode is selected but is not switched on (PaUSE).
F Set the programmed speed by accelerating to the required speed, then press button 2 or 3
(e.g.: 70 mph
(110 km/h)).
You can then change the programmed speed using buttons 2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
F Switch off the cruise control by pressing button
4 : the screen confirms that it has been switched off (PAUSE).
F Switch the cruise control back on by pressing button
4 again.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results in flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or unintentional deceleration of the vehicle, automatically cancels the flashing of the speed.
Leaving cruise control mode
F Turn thumb wheel
1 to the "0" position: the cruise control mode is deselected. The display returns to the distance recorder.
Operating fault
In the event of a cruise control malfunction, the speed is cleared resulting in flashing of the dashes. Have it checked by a CITRoËn dealer or a qualified workshop.
When the cruise control is switched on, be careful if you maintain the pressure on one of the programmed speed changing buttons: this may result in a very rapid change in the speed of your vehicle.
do not use the cruise control on slippery roads or in heavy traffic.
on a steep descent, the cruise control will not be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:
- ensure that the mat is secured correctly,
- never fit one mat on top of another.
Driving
Rear parking sensors
System consisting of four proximity sensors, located in the rear bumper.
Activation
This detects any obstacle (person, vehicle, tree, gate, etc.) behind the vehicle, except obstacles located just below the bumper.
An object, such as a stake, a roadworks cone or any other similar object may be detected at the beginning of the manoeuvre, but may no longer be detected when the vehicle comes close to it.
The system is activated as soon as reverse gear is engaged, accompanied by an audible signal. The proximity information is given by:
- an audible signal, which becomes more rapid as the vehicle approaches the obstacle.
- a graphic (according to version) in the multifunction screen, with blocks which become increasingly closer to the vehicle.
When the distance between the rear of the vehicle and the obstacle is less than thirty centimetres, the audible signal becomes continuous and the "danger" symbol appears in the multifunction screen.
On completion of the manoeuvre, when you exit reverse gear, the system becomes inactive.
The parking sensor system cannot in any circumstances take the place of vigilance on the part of the driver.
9
131
132
Driving
Programming
You can activate or deactivate the system by means of the multifunction screen configuration menu. The system state is memorised when switching off the ignition.
For more information on access to the parking sensors menu, refer to "Vehicle configuration" or "Vehicle parameters" section for your multifunction screen.
Operating faults
If there is an operating fault, when reverse gear is engaged this warning lamp comes on in the instrument panel, accompanied by an audible signal (short beep) and a message in the multifunction screen.
The system will be deactivated automatically when towing a trailer or when a bicycle carrier is fitted (vehicle fitted with a towbar or bicycle carrier recommended by CITRoËn).
In bad or wintry weather, ensure that the sensors are not covered with mud, frost or snow.
Driving
Reversing camera
a reversing camera is activated automatically when reverse gear is engaged.
The colour image is provided in the navigation screen.
The space between the blue lines represents the width of your vehicle except for the door mirrors.
The reversing camera cannot in any circumstances be a substitute for vigilance on the part of the driver.
The blue lines represent the general direction of the vehicle.
The red line represents a distance of about
30 cm beyond the edge of your vehicle's rear bumper. The audible signal becomes continuous from this limit.
The green lines represent distances of about 1 and 2 metres beyond the edge of your vehicle's rear bumper.
9
Clean the reversing camera regularly using a soft, dry cloth.
133
134
Checks
ToTaL & CITRoËn
Partners in performance and protecting the environment
Innovation in the search for performance
For over 40 year, the ToTaL Research and development departments have developed for
CITRoËn, lubricants to match the latest technical innovations on CITRoËn vehicles, both for competition and for everyday motoring.
For you, this is an assurance that you will obtain of the best performance for your engine.
Optimum protection for your engine
by having your CITRoËn vehicle serviced with TOTAL lubricants, you are contributing towards improving the life and performances of your engine, while also protecting the environment.
prefers
Checks
bonnet
Protects the components of the engine and provides access for checking levels.
Opening
before doing anything under the bonnet, switch off the Stop & Start system to avoid any risk of injury resulting from an automatic change to
STaRT mode.
F Unclip the bonnet stay C from its housing, holding it by its foam protection.
F Fix the stay in the notch to hold the bonnet open.
F open the front left door.
F Pull the interior release lever A , located at the bottom of the door aperture.
Closing
F Take the stay out of the support notch.
F Clip the stay in its housing.
F Lower the bonnet and release it at the end of its travel.
F Pull on the bonnet to check that it is fully latched.
F Push the exterior safety catch B to the left and raise the bonnet.
The location of the interior release lever prevents opening of the bonnet while the front left door is closed.
When the engine is hot, handle the exterior safety catch and the stay with care.
To avoid damaging the electric units, the use of a high pressure jet wash under the bonnet is strictly prohibited.
10
135
136
Checks
Running out of fuel
(diesel)
If your vehicle is fitted with an HDI engine, the fuel system must be primed if you run out of fuel.
This system consists of a priming pump and a transparent pipe under the bonnet.
F Fill the fuel tank with at least five litres of diesel.
F open the bonnet.
F depending on version, unclip the cover to gain access to the priming pump.
F Squeeze and release the priming pump until resistance is felt (could be from the first application) and fuel appears in the transparent pipe with the green connector.
F operate the starter until the engine starts.
F depending on version, put the cover back in position and clip it in place.
F Close the bonnet.
If the engine does not start at the first attempt, do not try again.
operate the priming pump again, then the starter.
Petrol engines
1.
Screenwash fluid reservoir.
2.
Coolant header tank.
3.
air filter.
4.
brake fluid reservoir.
5.
battery.
6.
Fusebox.
7.
Engine oil dipstick.
8.
Engine oil filler cap.
Checks
10
137
138
Checks
diesel engines
1.
Screenwash fluid reservoir.
2.
Coolant header tank.
3.
air filter.
4.
brake fluid reservoir.
5.
battery.
6.
Fusebox.
7.
Engine oil dipstick.
8.
Engine oil filler cap.
9.
Priming pump (on fuel filter).
Checks
Checking levels
Check all of these levels regularly, in line with the maintenance and warranty guide. Top them up if necessary, unless otherwise indicated.
If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop.
Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start at any time
(even with the ignition off).
Engine oil level
The check is carried out either when the ignition is switched on using the oil level indicator in the instrument panel for vehicles with an electric oil level gauge, or using the dipstick.
Checking using the dipstick
Refer to the "Petrol engine" or "diesel engine" section for the location of the dipstick in the engine compartment of your vehicle.
F Take the dipstick by its coloured grip and remove it completely.
F Wipe the end of the dipstick using a clean non-fluffy cloth.
F Refit the dipstick and push fully down, then pull it out again to make the visual check: the correct level is between the marks
A and B .
If you find that the level is above the A mark or below the
B mark, do not start the engine .
- If the level is above the MAX mark (risk of damage to the engine), contact a
CITROËN dealer or a qualified workshop.
- If the level is below the
MIN mark, you must top up the engine oil.
To ensure that the reading is correct, your vehicle must be parked on a level surface with the engine having been off for more than 30 minutes.
A = MaX
Oil grade
before topping-up the oil or changing the oil, check that the oil is the correct grade for your engine and conforms to the manufacturer's recommendations.
10
It is normal to top up the oil level between two services (or oil changes). CITROËN recommends that you check the level, and top up if necessary, every 3 000 miles (5 000 kms).
B = MIn
139
140
Checks
Topping up the engine oil level
Refer to the "Petrol engine" or "diesel engine" section for the location of the oil filler cap in the engine compartment of your vehicle.
F Unscrew the oil filler cap to reveal the filler aperture.
F add oil in small quantities, avoiding any spills on engine components (risk of fire).
F Wait a few minutes before checking the level again using the dipstick.
F add more oil if necessary.
F after checking the level, carefully refit the oil filler cap and the dipstick in its tube.
Engine oil change
Refer to the maintenance and warranty guide for details of the interval for this operation.
In order to maintain the reliability of the engine and emission control system, never use additives in the engine oil.
Brake fluid level
The brake fluid level should be close to the "MaX" mark. If it is not, check the brake pad wear.
Changing the fluid
Refer to the maintenance and warranty guide for details of the interval for this operation.
Fluid specification
The brake fluid must conform to the manufacturer's recommendations.
After topping up the oil, the check when switching on the ignition with the oil level indicator in the instrument panel is not valid during the 30 minutes after topping up.
Checks
Coolant level
The coolant level should be close to the "MaX" mark but should never exceed it.
When the engine is warm, the temperature of the coolant is regulated by the fan.
The cooling fan may start after switching off the engine: take care with articles and clothing that might be caught by the fan blades.
In addition, as the cooling system is pressurised, wait at least one hour after switching off the engine before carrying out any work.
To avoid any risk of scalding, unscrew the cap by two turns to allow the pressure to drop. When the pressure has dropped, remove the cap and top up the level.
Changing the coolant
The coolant does not have to be replaced at routine services.
Fluid specification
The coolant must conform to the manufacturer's recommendations.
Screenwash fluid level
Top up the level when necessary.
Fluid specification
For optimum cleaning and to avoid freezing, this fluid must not be topped up or replaced with plain water.
In wintry conditions, it is recommended that you use an ethyl alcohol or methanol based fluid.
Used products
avoid prolonged contact of used oil or fluids with the skin.
Most of these fluids are harmful to health or indeed very corrosive.
do not discard used oil or fluids into sewers or onto the ground.
Take used oil to a CITRoËn dealer or a qualified workshop (France) or to an authorised waste disposal site.
Additive level (Diesel with particle emissions filter)
according to your version of instrument panel, the additive reservoir low level is indicated by:
- fixed illumination of the particle emissions filter warning lamp, accompanied by an audible signal, or
- fixed illumination of the service warning lamp, accompanied by an audible signal and a message that the particle emissions filter additive level is too low.
Topping up
The reservoir must be topped up without delay by a CITROËN dealer or a qualified workshop.
10
141
142
Checks
Checks
Unless otherwise indicated, check these components in accordance with the maintenance and warranty guide and according to your engine.
Otherwise, have them checked by a CITROËN dealer or a qualified workshop.
12 V battery
The battery does not require any maintenance.
However, check that the terminals are clean and correctly tightened, particularly in summer and winter.
When carrying out work on the battery, refer to the "12 V battery" section for details of the precautions to be taken before disconnecting the battery and following its reconnection.
The presence of this label, in particular with the Stop & Start system, indicates the use of a specific 12 V lead-acid battery with special technology and specification. The involvement of a CITROËN dealer or a qualified workshop is essential when replacing or disconnecting the battery.
Air filter and passenger compartment filter
Refer to the maintenance and warranty guide for details of the replacement intervals for these components.
depending on the environment (e.g. dusty atmosphere) and the use of the vehicle (e.g. city driving), replace them twice as often if necessary .
a clogged passenger compartment filter may have an adverse effect on the performance of the air conditioning system and generate undesirable odours.
Oil filter
Replace the oil filter each time the engine oil is changed.
Refer to the maintenance and warranty guide for details of the replacement interval for this component.
Particle emission filter (Diesel)
according to your version of instrument panel, the start of saturation of the particle emissions filter is indicated by:
- fixed illumination of the particle emissions filter warning lamp, accompanied by an audible signal, or
temporary illumination of the service warning lamp, accompanied by an audible signal and a message that there is a risk of blockage of the particle emissions filter.
as soon as the traffic conditions permit, regenerate the filter by driving at a speed of at least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the
"additive level" section.
On a new vehicle, the first operations of regeneration of the particle emissions filter may be accompanied by the smell of "burning", which is perfectly normal.
Following prolonged operation of the vehicle at very low speed or at idle, you may, in exceptional circumstances, notice the emission of water vapour at the exhaust on acceleration. This does not affect the behaviour of the vehicle or the environment.
Checks
Manual gearbox
The gearbox does not require any maintenance (no oil change).
Refer to the maintenance and warranty guide for the checking interval for this component.
Electronic gearbox
The gearbox does not require any maintenance (no oil change).
Refer to the maintenance and warranty guide for details of the checking interval for this component.
Brake pads
Brake wear depends on the style of driving, particularly in the case of vehicles used in town, over short distances. It may be necessary to have the condition of the brakes checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fluid level indicates that the brake pads are worn.
Brake disc wear
For information on checking brake disc wear, contact a CITROËN dealer or a qualified workshop.
Automatic gearbox
The gearbox does not require any maintenance (no oil change).
Refer to the maintenance and warranty guide for details of the level checking interval for this component.
Parking brake
If excessive travel or a loss of effectiveness of this system is noticed, the parking brake must be checked, even between two services.
Checking this system must be done by a
CITROËN dealer or a qualified workshop.
only use products recommended by
CITRoËn or products of equivalent quality and specification.
In order to optimise the operation of units as important as those in the braking system, CITRoËn selects and offers very specific products.
After washing the vehicle, dampness, or in wintry conditions, ice can form on the brake discs and pads: braking efficiency may be reduced. Make light brake applications to dry and defrost the brakes.
10
143
144
Practical information
Temporary puncture repair kit
Complete system consisting of a compressor and a sealant cartridge which permits temporary repair of a tyre so that you can drive to the nearest garage.
It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.
Access to the kit Composition of the kit
This kit is installed in the storage box, under the boot floor.
1.
12 V compressor, with integral pressure gauge.
2.
Sealant cartridge, with integral hose.
3.
Speed limit sticker.
The vehicle's electric system allows the connection of a compressor for long enough to inflate a tyre after a puncture repair or for inflating a small inflatable accessory.
The speed limit sticker must be secured to the interior of the vehicle in the driver's field of vision, to remind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph
(80 km/h) when driving with a tyre repaired using this type of kit.
Practical information
Repair procedure
F Switch off the ignition.
F Secure the speed limit sticker inside the vehicle.
F Uncoil the pipe stowed under the compressor.
F Connect the pipe from the compressor to the sealant cartridge.
F Turn the the sealant cartridge and secure it in the cut-out provided on the compressor.
F Remove the valve cap from the tyre to be repaired, and place it in a clean area.
F Connect the hose from the sealant cartridge to the valve of the tyre to be repaired and tighten firmly.
avoid removing any foreign bodies which have penetrated into the tyre.
11
145
Practical information
If after around 5 to 7 minutes the pressure is not attained, this indicates that the tyre is not repairable; contact a CITRoËn dealer or a qualified workshop for assistance.
146
F Check that the compressor switch is at the " O " position).
F Uncoil fully the electric cable, stowed under the compressor.
F Connect compressor's plug to the vehicle's
12 V socket.
F Switch on the ignition.
F Start the compressor by placing the switch at the " I " position and leave it running until the tyre pressure reaches 2.0 bar.
The sealant product is injected into the tyre under pressure; do not disconnect the pipe from the valve during this operation (risk of splashing and stains).
Take care, the sealant product is harmful (e.g. ethylene-glycol, colophony...) if swallowed and causes irritation to the eyes.
keep this product out of the reach of children.
The use-by date is marked on the cartridge.
after use, do not discard the cartridge by the roadside, take it to a CITRoËn dealer or an authorised waste disposal site.
Don't forget to obtain a new sealant cartridge, available from a CITRoËn dealer or a qualified workshop.
Checking / adjusting tyre pressures
Practical information
F Place the switch in the "
O " position.
F Remove the kit.
F drive immediately for approximately three miles (five kilometres), at reduced speed (between 15 and 35 mph (20 and
60 km/h)), to plug the puncture.
F Stop to check the repair and the tyre pressure using the kit.
You can also use the compressor, without injecting sealant, to check and if necessary adjust the tyre pressures.
F Remove the valve cap from the tyre and place it in a clean area.
F Uncoil the pipe stowed under the compressor.
F Screw the pipe onto the valve and tighten firmly.
F Check that the compressor switch is at the
" O " position.
F Uncoil fully the electric cable, stowed under the compressor.
F Connect compressor's plug to the vehicle's
12 V socket.
F Switch on the ignition.
11
147
148
Practical information
Tyre under-inflation detection
After repair of the tyre, the warning lamp will remain on until the system is reinitialised.
For more information, refer to the
"Under-inflation detection" section.
F Start the compressor by placing the switch at the " I " position and adjust the pressure to the value shown on the vehicle's tyre pressure label.
To deflate: press the black button on the compressor pipe, at the valve connector.
F once the correct pressure is reached, put the switch to the "
O " position.
F Remove the kit then stow it.
Should the pressure of one or more tyres be adjusted, it is necessary to reinitialise the under-inflation detection system.
Refer to the "Under-inflation detection" section.
Practical information
Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
Access to the tools
The tools are installed in the boot under the floor.
To gain access to them:
F open the boot,
F raise the floor,
F remove the polystyrene storage box,
F unclip and remove the box containing the tools.
List of tools
all of these tools are specific to your vehicle. do not use them for other purposes.
1.
Wheelbrace.
For removing the wheel trim and removal of the wheel fixing bolts.
2.
Jack with integral handle.
For raising of the vehicle.
3.
"bolt cover" tool.
For removing the bolt protectors (covers) on alloy wheels.
4.
Socket for the security wheel bolts (located in the glove box).
For adapting the wheelbrace to the special
"security" wheel bolts (if your vehicle has them).
11
149
150
Practical information
Wheel with trim
When removing the wheel , first detach the trim using the wheelbrace
1 pulling at the valve passage hole.
When refitting the wheel , refit the trim starting by placing its cut-out at the valve and press around its edge with the palm of your hand.
Access to the spare wheel
The spare wheel is installed in the boot under the floor.
According to country, the spare wheel may be steel or of the "space-saver" type.
To gain access to it, refer to the paragraph
"access to the tools" on the previous page.
Fitting the steel or "spacesaver" type spare wheel
If your vehicle is fitted with alloy wheels, it is normal to notice, when tightening the bolts on fitting, that the washers do not come into contact with the steel or
"space-saver" type spare wheel. The wheel is secured by the conical contact of each bolt.
Practical information
Taking out the wheel
F Unscrew the yellow central bolt.
F Raise the spare wheel towards you from the rear.
F Take the wheel out of the boot.
Putting the wheel back in place
F Put the wheel back in its housing.
F Unscrew the yellow central bolt by a few turns then put it in place in the centre of the wheel.
F Tighten fully until the central bolt clicks to retain the wheel correctly.
F Put the box back in place in the centre of the wheel and clip it.
F Put the polystyrene storage box back in place.
F Refit the boot floor carpet by lightly folding it in two (refer to the section
"Fittings - § Storage box").
On vehicles equipped with a "spacesaver" type spare wheel, the punctured wheel cannot be stowed in place of the
"space-saver" wheel.
11
151
152
Practical information
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery.
Apply the parking brake, switch off the ignition and engage first gear* to lock the wheels.
If necessary, place a chock under the wheel diagonally opposite the wheel to be changed.
It is imperative that you ensure that the occupants get out of the vehicle and wait where they are safe.
never go underneath a vehicle raised using a jack; use an axle stand.
List of operations
F Remove the bolt cover from each of the bolts using the tool 3
(with alloy wheels only).
F Fit the security bolt socket 4 on the wheelbrace
1 to slacken the security bolt
(if your vehicle has them).
F Slacken the other bolts using the wheelbrace
1 only.
* position R
for an electronic gearbox; position P for an automatic gearbox.
Practical information
F Position the foot of the jack 2 on the ground, ensuring that it is directly below the front A or rear B jacking points provided on the underbody, whichever is closest to the wheel to be changed.
F Extend the jack 2 until its head comes into contact with the jacking point
A or B used.
The vehicle's contact surface A or B must be fully engaged with the central part of the head of the jack.
F Raise the vehicle until there is sufficient space between the wheel and the ground to admit the spare (not punctured) wheel easily.
F Remove the bolts and store them in a clean place.
F Remove the wheel.
Ensure that the jack is stable. If the ground is slippery or loose, the jack could slip or drop - Risk of injury!
Position the jack only at one of the jacking points A or B under the vehicle, ensuring that the vehicle's contact surface is positioned centrally on the head of the jack. Otherwise, there is a risk of damage to the vehicle and/or the jack dropping - Risk of injury!
11
153
154
Practical information
Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover.
When using the "space-saver" type temporary use spare wheel, do not exceed 50 mph (80 km/h).
Have the tightening of the bolts and the pressure of the spare wheel checked by a CITRoËn dealer or a qualified workshop without delay.
Have the punctured wheel repaired and replace it on the vehicle as soon as possible.
Do not drive with more than one temporary use spare wheel fitted to the vehicle at one time.
List of operations
F Put the wheel in place on the hub.
F Screw in the bolts by hand.
F Pre-tighten the security bolt (if your vehicle has them) using the wheelbrace
1 fitted with the security bolt socket
4 .
F Pre-tighten the other bolts using the wheelbrace
1 only.
Practical information
F Lower the vehicle fully.
F Fold the jack 2 and detach it.
F Tighten the security bolt (if your vehicle has them) using the wheelbrace
1
fitted with the security bolt socket 4 .
F Tighten the other bolts using the wheelbrace
1 only.
F Refit the bolt covers on each of the bolts.
F Store the tools in the box.
11
155
156
Practical information
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking.
The snow chains must be fitted only to the front wheels. They must never be fitted to "space-saver" type spare wheels.
Use only the chains designed to be fitted to the type of wheel fitted to your vehicle: original tyre size
185/65 R15
195/55 R16
205/45 R17
Maximum link size.
9 mm
7 mm
For more information on snow chains, contact a
CITROËN dealer or a qualified workshop.
Take account of the legislation in force in your country on the use of snow chains and the maximum running speed authorised.
Advice on installation
F If you have to fit the chains during a journey, stop the vehicle on a flat surface on the side of the road.
F apply the parking brake and position any wheel chocks to prevent movement of your vehicle.
F Fit the chains following the instructions provided by the manufacturer.
F Move off gently and drive for a few moments, without exceeding 30 mph
(50 km/h).
F Stop your vehicle and check that the snow chains are correctly tightened.
Avoid driving with snow chains on roads that have been cleared of snow, to avoid damaging your vehicle's tyres and the road surface. If your vehicle is fitted with alloy wheels, check that no part of the chain or its fixings is in contact with the wheel rim.
It is strongly recommended that before you leave, you practise fitting the snow chains on a level and dry surface.
Practical information
Changing a bulb
The headlamps are fitted with polycarbonate glass with a protective coating:
F do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,
F use a sponge and soapy water or a pH neutral product,
F when using a high pressure washer on persistent marks, do not keep the lance directed towards the lamps or their edges for too long, so as not to damage their protective coating and seals.
Changing a bulb should only be done after the headlamp has been switched off for several minutes (risk of serious burns).
F Do not touch the bulb directly with your fingers, use a lint-free cloth.
It is imperative to use only antiultraviolet (UV) type bulbs to avoid damaging the headlamp.
Always replace a failed bulb with a new bulb with the same type and specification.
Front lamps
1.
Direction indicators (PY21W amber).
2.
Sidelamps (W5W).
3.
Main beam headlamps (H1-55W).
4.
Dipped beam headlamps (H7-55W).
5.
LED daytime running lamps.
6.
Front foglamps (PSX24W).
11
157
Practical information
158
Changing direction indicator bulbs
Rapid flashing of the direction indicator warning lamp (right or left) indicates the failure of a bulb on that side.
F Turn the bulb holder a quarter of a turn and extract it.
F Pull out the bulb and change it.
To refit, carry out these operations in reverse order.
amber coloured bulbs, such as the direction indicators, must be replaced with bulbs of identical specifications and colour.
Changing dipped beam headlamp bulbs
F Remove the protective cover by pulling the tab.
F disconnect the bulb connector.
F Spread the springs to release the bulb.
F Pull the bulb out and change it.
To refit, carry out these operations in reverse order.
When refitting, close the protective cover carefully to preserve the sealing of the headlamp.
Practical information
Changing main beam headlamp bulbs
F Remove the protective cover by pulling on the tab.
F disconnect the bulb connector.
F Spread the springs to release the bulb.
F Remove the bulb and change it.
To refit, carry out these operations in reverse order.
Changing sidelamp bulbs
F Remove the protective cover by pulling on the tab.
F Pull the bulb holder pressing on the tabs on both sides.
F Pull the bulb and change it.
To refit, carry out these operations in reverse order.
11
159
Practical information
160
Changing integrated direction indicator side repeaters
F Insert a screwdriver towards the centre of the repeater between the repeater and the base of the door mirror.
F Tilt the screwdriver to extract the repeater and remove it.
F disconnect the repeater connector.
F Replace the module.
To refit, carry out these operations in reverse order.
Contact a CITRoËn dealer or a qualified workshop to obtain a replacement side repeater module.
Changing front foglamp bulbs
F access to the front foglamp is through the aperture below the bumper.
F disconnect the black bulb holder connector, by pressing on the tab at the top.
F Remove the bulb-holder by pressing on the
2 clips (at the top and the bottom).
F Replace the module.
To refit, carry out these operations in reverse order.
To obtain a replacement module, contact your CITRoËn dealer or a qualified workshop.
If you experience any difficulty in replacing bulbs, contact your CITRoËn dealer or a qualified workshop.
Practical information
Rear lamps
1.
Brake / sidelamps (P21/5W).
2.
Direction indicators (PY21W amber).
3.
Foglamp, right-hand side (PR21W red)
Reversing lamp, left-hand side (P21W).
amber or red bulbs, such as those for the direction indicators and rear foglamp, must be replaced by bulbs of the same rating and colour.
The lamps on the tailgate are dummy units. They are there for aesthetic purposes only.
Changing bulbs
These four bulbs are changed from inside the boot:
F open the boot,
F remove the access flap from the corresponding side trim panel,
F unscrew the butterfly nut securing the lamp unit,
F unclip the lamp unit connector,
F extract the lamp unit carefully pulling in its middle towards the outside,
F spread the four tabs and remove the bulb holder,
F turn the bulb a quarter of a turn and change it.
To refit, carry out these operations in reverse order.
Take care to engage the lamp unit in its guides, while keeping it in line with the vehicle.
11
161
Practical information
162
Changing the number plate lamp bulbs (W5W)
F Insert a thin screwdriver into one of the outer holes of the lens.
F Push it outwards to unclip.
F Remove the lens.
F Pull the bulb out and change it.
Third brake lamp
(4 W5W bulbs)
F open the boot.
F Remove the plugs A on the inner panel.
F Push on the centre of the lamp using two screwdrivers to lever it outwards.
F disconnect the connector and if necessary the screenwash pipe from the lamp.
F Turn the bulb holder for the faulty bulb a quarter of a turn.
F Pull out the bulb and change it.
To refit, carry out these operations in reverse order.
Practical information
Interior lighting
Interior lamp (1 / W5W)
Unclip the cover of the interior lamp 1
with a thin screwdriver, close to the button, to access the faulty bulb.
Boot lamp (W5W)
Unclip the unit by pushing it from the rear.
Side reading lamps (2 / W5W)
Unclip the cover of the reading lamp 2
with a small screwdriver at the switch end for access to the faulty bulb.
Central storage lamps (W5W)
Unclip the lamp for access to the bulb.
11
163
164
Practical information
Changing a fuse
Procedure for replacing a faulty fuse with a new fuse to rectify a failure of the corresponding function.
Access to the tools Changing a fuse
before changing a fuse, the cause of the failure must be identified and rectified.
F Identify the faulty fuse by checking the condition of its filament.
The extraction tweezer and the spare fuse storage locations are fitted to the back of the dashboard fusebox cover.
For access to them:
F open the glove box lid,
F unclip the fusebox cover by pulling on the side,
F remove the cover completely,
F remove the tweezer.
Good Failed
F Use the special tweezer to extract the fuse from its housing.
F Always replace the failed fuse with a fuse of the same rating.
F Check that the number marked on the box, the rating marked on the fuse and the tables below all agree.
Installing electrical accessories
Your vehicle's electrical system is designed to operate with standard or optional equipment.
before installing other electrical equipment or accessories on your vehicle, contact a CITRoËn dealer or a qualified workshop.
CITROËN will not accept responsibility for the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and not recommended by CITRoËn and not installed in accordance with its instructions, in particular when the combined consumption of all of the additional equipment connected exceeds 10 milliamperes.
Practical information
Dashboard fusebox
The fusebox is placed in the lower dashboard
(left-hand side).
Fuse tables
Fuse N°
FH36
FH37
FH38
FH39
FH40
Rating
5 A
-
20 A
-
40 A
Trailer relay unit.
not used.
HiFi amplifier.
not used.
Trailer relay unit.
Access to the fuses
F Refer to the paragraph "access to the tools".
Fuse N°
F1
F2
F3
F4
F5
F6
F7
Rating
-
-
5 A
10 A
30 A
30 A
5 A
Functions
Functions not used.
not used.
airbags and pretensioners control unit.
Air conditioning, clutch switch, electrochromatic mirror, particle filter pump (Diesel), diagnostic socket, airflow sensor (Diesel).
Electric windows panel, passenger's electric window control, front electric window motor.
Rear electric windows motors and driver's electric window motor.
11
Courtesy lamp, side reading lamps.
165
166
Practical information
F9
F10
F11
F12
F13
F14
F15
F16
F17
SH
Fuse N°
F8
15 A
30 A
-
40 A
-
15 A
15 A
15 A
5 A
Rating
20 A
30 A
Functions
Multifunction screen, audio system, navigation radio, instrument panel with clock, alarm control unit, alarm siren, audio system
(after-market), portable navigation system carrier supply.
Multifunction screen, audio system, navigation audio unit, instrument pnael with clock, alarm control unit, alarm siren, audio system (after-market), 12 V socket, portable navigation support supply, locking.
Steering mounted controls.
Ignition, diagnostic socket, automatic gearbox control unit.
Rain / sunshine sensor, trailer relay unit, driving school module.
Main stop switch, engine relay unit, electronic gearbox gear lever.
Parking sensors control unit, airbag control unit, instrument panel, automatic air conditioning, USb box, HiFi amplifier, reversing camera.
Locking.
not used.
Rear screen and door mirrors demisting/defrosting.
PaRC shunt.
Engine compartment fusebox
The fusebox is placed in the engine compartment near the battery (left-hand side).
All work on the fuses in the fusebox at the battery must be done by a
CITRoËn dealer or a qualified workshop.
Access to the fuses
F Unclip the cover.
F Change the fuse (see corresponding paragraph).
F When you have finished, close the cover carefully to ensure the sealing of the fusebox.
Practical information
11
167
168
Practical information
Fuse table
Fuse N°
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
Rating
20 A
15 A
10 A
20 A
15 A
10 A
10 A
25 A
10 A
30 A
40 A
Functions
Engine control unit supply, cooling fan unit control relay, multifunction engine control main relay, injection pump (diesel).
Horn.
Front / rear wash-wipe.
daytime running lamps, LEd daytime running lamps.
diesel heater (diesel), particle filter additive pump (diesel), air flow sensor (Diesel), fuel pump (1.1i and 1.4i), blow-by heater and electrovalves (VTi).
ABS/ESP control unit, secondary stop switch.
Electric power steering, automatic gearbox.
Starter control.
Switching and protection unit (Diesel).
Fuel heater (Diesel), blow-by heater (1.1i, 1.4i and Diesel), fuel pump (VTi), injectors and ignition coils (petrol), electronic thermostat and canister purge electrovalve (1.1i and 1.4i).
Heater blower.
Practical information
Fuse N°
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
Rating
30 A
40 A
30 A
10 A
10 A
15 A
15 A
15 A
10 A
5 A
Functions
Windscreen wipers slow / fast speed.
built-in systems interface supply (ignition positive).
Valvetronic supply (VTi).
Right-hand main beam headlamps.
Left-hand main beam headlamps.
Left-hand dipped beam headlamps.
Right-hand dipped beam headlamps.
oxygen sensors and electrovalves (VTi), electrovalves
(diesel), EGR electrovalve (diesel).
Pumps, electronic thermostat (VTi), water in fuel sensor
(diesel).
Fan assembly control supply, abS/ESP.
11
169
170
Practical information
Table of maxi-fuses
Fuse N°
MF1*
MF2*
MF3*
MF4*
MF5*
MF6*
MF7*
MF8*
Rating
60 A
30 A
30 A
60 A
60 A
-
80 A
-
Functions
Fan assembly.
abS / ESP pump.
abS / ESP electrovalves.
built-in Systems Interface (bSI) supply.
built-in Systems Interface (bSI) supply.
not used.
dashboard fusebox.
not used.
* The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried out by a CITROËN dealer or a qualified workshop.
Practical information
battery
Procedure for charging your battery when it is flat or for starting the engine using another battery.
after refitting the battery by a CITRoËn dealer or a qualified workshop, the Stop & Start system will only be active after a continuous period of immobilisation of the vehicle, a period which depends on the climatic conditions and the state of charge of the battery (up to about 8 hours).
The presence of this label, in particular with the Stop & Start system, indicates the use of a 12 V lead-acid battery with special technology and specification; the involvement of a CITRoËn dealer or a qualified workshop is essential when replacing or disconnecting the battery.
Failure to observe this recommendation may cause premature wear of the battery.
Access to the battery
The battery is located under the bonnet.
To gain access to it:
F open the bonnet using the interior release lever, then the exterior safety catch,
F secure the bonnet stay,
F lift the plastic cover on the (+) terminal.
11
171
Practical information
172
Starting using another battery
When the battery on your vehicle is discharged, the engine can be started using a slave battery
(external or on another vehicle) and jump leads.
First check that the slave battery has a nominal voltage of 12 V and a capacity at least equal to that of the discharged battery.
do not try to start the engine by connecting a battery charger.
Do not disconnect the (+) terminal when the engine is running.
F Connect the red cable to the positive terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B .
F Connect one end of the green or black cable to the negative terminal (-) of the slave battery B (or earth point on the other vehicle).
F Connect the other end of the green or black cable to the negative terminal C (or the engine mounting) of the broken-down vehicle.
F Start the engine of the other vehicle and allow it to run for a few minutes.
F Operate the starter of the broken-down vehicle and let the engine run.
If the engine does not start immediately, switch off the ignition and wait a few moments before trying again.
F Wait until the engine returns to idle, then disconnect the jump leads in reverse order.
Charging the battery using a battery charger
F Follow the instructions for use provided by the manufacturer of the charger.
do not disconnect the battery to charge it.
batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordance with regulations and must not, in any circumstances, be discarded with household waste.
Take used remote control batteries and vehicle batteries to a special collection point.
Protect your eyes and face before handling the battery.
all operations on the battery must be carried out in a well ventilated area away from naked flames and sources of sparks, so as to avoid the risk of explosion and fire.
Do not try to charge a frozen battery; the battery must first be thawed out to avoid the risk of explosion. If the battery has been frozen, before charging have it checked by a CITRoËn dealer or a qualified workshop who will check that the internal components have not been damaged and the casing is not cracked, which could cause a leak of toxic and corrosive acid.
do not reverse the polarity and use only a 12 V charger.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals first.
Wash your hands afterwards.
do not push the vehicle to start the engine if you have an electronic gearbox or automatic gearbox.
Some functions are not available if the battery is not sufficiently charged.
Practical information
11
173
174
Practical information
Load reduction mode
System which manages the use of certain functions according to the level of charge remaining in the battery.
When the vehicle is being driven, the load reduction function temporarily deactivates certain functions, such as the air conditioning, the heated rear screen...
The deactivated functions are reactivated automatically as soon as conditions permit.
Energy economy mode
System which manages the period of use of certain functions to conserve a sufficient level of charge in the battery.
after the engine has stopped, you can still use functions such as the audio equipment, windscreen wipers, dipped beam headlamps, courtesy lamps, etc. for a maximum combined period of thirty minutes.
This period may be greatly reduced if the battery is not fully charged.
Exiting economy mode
These functions are reactivated automatically the next time the vehicle is driven.
F In order to resume the use of these functions immediately, start the engine and let it run for a few minutes.
The time available to you will then be double the period for which the engine is left running.
However, this period will always be between five and thirty minutes.
Switching to economy mode
once this period has elapsed, a message appears on the multifunction screen indicating that the vehicle has switched to economy mode and the active functions are put on standby.
If the telephone is being used at the same time on the eMyWay audio navigation system, it will be interrupted after 10 minutes.
a flat battery prevents the engine from starting (refer to the corresponding paragraph).
Changing a front or rear wiper blade
Procedure for replacing a worn wiper blade with a new one without the use of tools.
Before removing a front wiper blade
F Within one minute after switching off the ignition, operate the wiper stalk to position the wiper blades in the vertical position.
This position must be used in order to avoid damaging the wiper blade and the bonnet.
Fitting
F At the front, check the size of the wiper blade as the shorter blade is fitted to the passenger side of the vehicle.
F Put the corresponding new wiper blade in place and clip it.
F Fold down the wiper arm carefully.
Removal
F Raise the corresponding wiper arm.
F Unclip the wiper blade and remove it.
After fitting a front wiper blade
F Switch on the ignition.
F Operate the wiper stalk again to park the wiper blades.
Practical information
11
175
176
Practical information
Towing the vehicle
Procedure for having your vehicle towed or for towing another vehicle using a removable towing eye.
Access to the tools
The towing eye is installed in the boot under the floor.
To gain access to it:
F open the boot,
F raise the floor,
F remove the polystyrene storage box,
F remove the towing eye from the holder.
General recommendations
observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed vehicle.
The driver must remain at the wheel of the towed vehicle and must have a valid driving licence.
When towing a vehicle with all four wheels on the ground, always use an approved towing arm; rope and straps are prohibited.
The towing vehicle must move off gently.
When towing a vehicle with the engine off, there is no longer any power assistance for braking or steering.
In the following cases, you must always call on a professional recovery service:
- vehicle broken down on a motorway or fast road,
- four-wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing arm available...
Practical information
Towing another vehicle Towing your vehicle
F
on the front bumper, unclip the cover by pressing at the bottom.
F Screw the towing eye in fully.
F Install the towing bar.
F Place the gear lever in neutral (position N for an electronic or automatic gearbox).
Failure to observe this special condition could result in damage to certain components (braking, transmission...) and the absence of braking assistance the next time the engine is started.
F Unlock the steering by turning the key one notch in the ignition switch and release the parking brake.
F Switch on the hazard warning lamps on both vehicles.
F Move off gently and drive for a short distance only.
F on the rear bumper, unclip the cover by pressing at the bottom.
F Screw the towing eye in fully.
F Install the towing bar.
F Switch on the hazard warning lamps on both vehicles.
F Move off gently and drive for a short distance only.
11
177
178
Practical information
Towing a trailer
Your vehicle is primarily designed for transporting people and luggage, but it may also be used for towing a trailer.
We recommend the use of genuine
CITROËN towbars and their harnesses that have been tested and approved from the design stage of your vehicle, and that the fitting of the towbar is entrusted to a CITRoËn dealer or a qualified workshop.
If the towbar is not fitted by a
CITRoËn dealer, it must still be fitted in accordance with the vehicle manufacturer's instructions.
Driving with a trailer places greater demands on the towing vehicle and the driver must take particular care.
Driving advice
Distribution of loads
F distribute the load in the trailer so that the heaviest items are as close as possible to the axle and the nose weight approaches the maximum permitted without exceeding it.
Air density decreases with altitude, thus reducing engine performance. above
1 000 metres, the maximum towed load must be reduced by 10 % for every 1 000 metres of altitude.
Refer to the "Technical data" section for details of the weights and towed loads which apply to your vehicle.
Side wind
F Take into account the increased sensitivity to side wind.
Cooling
Towing a trailer on a slope increases the temperature of the coolant.
as the fan is electrically controlled, its cooling capacity is not dependent on the engine speed.
F To lower the engine speed, reduce your speed.
The maximum towed load on a long incline depends on the gradient and the ambient temperature.
In all cases, keep a check on the coolant temperature.
Braking
Towing a trailer increases the braking distance.
To avoid overheating of the brakes on a long mountain type of descent, the use of engine braking is recommended.
Tyres
F Check the tyre pressures of the towing vehicle and of the trailer, observing the recommended pressures.
F If the warning lamp and the
STOP
warning lamp come on, stop the vehicle and switch off the engine as soon as possible.
Lighting
F Check the electrical lighting and signalling on the trailer.
The rear parking sensors will be deactivated automatically if a genuine
CITROËN towbar is used.
Practical information
11
179
Practical information
audio pre-equipment
Your vehicle is equipped with certain factoryfitted audio equipment:
- a dual-function aerial at the rear of the roof,
- a coaxial aerial cable,
- basic interference suppression,
- cabling for speakers in the front doors and tweeters in the dashboard,
- cabling for speakers in the rear doors
- a 40-way connector.
Fitting an audio unit
The audio unit is fitted in place of one of the storage boxes located below the heating and air conditioning control panel.
Fitting speakers
It is possible to fit:
- 165 mm diameter speakers in the front doors,
- 130 mm diameter speakers in the rear doors,
- 22.5 mm diameter tweeters in the top of the dashboard.
180 before installing a radio unit or speakers in your vehicle, you can contact a CITROËN dealer who will give you the part number for a suitable wiring harness.
F Unclip the storage box on each side using a screwdriver and pull out.
You will then have access to an aerial coaxial cable and a 40-way connector.
Then refer to the instructions provided with your audio unit.
Connector lines
a1
A2 a3
(+) Right hand rear speaker
(+) Right hand front speaker and tweeter
(+) Left hand front speaker and tweeter a4 (+) Left hand rear speaker
A5
(-) Right hand rear speaker a6
(-) Right hand front speaker and tweeter
A7 (-) Left hand front speaker and tweeter a8 (-) Left hand rear speaker a9 not used a10 not used a11 not used
A12
(+) Permanent a13 not used a14 not used
A15 (+) Ignition switched (operation of the audio system only with the ignition on) a16 Earth
Practical information
Never use a separate wire to connect the (+) of your audio equipment (risk of discharging of the battery).
11
181
182
Practical information
accessories
A wide range of accessories and genuine parts is available from the CITROËN dealer network.
These accessories and parts are all suitable for your vehicle and benefit from CITROËN's recommendation and warranty.
Conversion kits
You can obtain an "Enterprise" kit to convert a trade vehicle to a private car and vice-versa.
"Comfort" sun blinds, door deflectors, insulated module, smoking kit, fragrance cartridges, front centre armrest, moveable mirror, reading lamp, front and rear parking sensors, cup holder, coat hanger for head restraint, solar film for windows, security film for windows...
"Transport solutions": boot tray, boot carpet, boot net, boot containers, transverse roof bars, bicycle carrier, ski carrier, roof boxes, towbars, towbar wiring harnesses...
"Security and safety": anti-theft alarm, wheel security bolts, stolen vehicle tracking system, breathalyser, first aid kit, warning triangle, high visibility vest, dog guard, snow chains, non-slip covers, foglamps kit, child seats and booster cushions, pet transport protectors...
If a towbar and wiring are fitted outside the CITROËN dealer network, this must be done making use of the vehicle's electrical pre-equipment and following the manufacturer's recommendations.
"Protection": mats*, mudflaps, seat covers, door sill protectors, bumper protection strips, vehicle protective cover, side protectors, boot mat, boot liner...
"Style": leather steering wheel, gear lever knobs, front spoiler, rear diffuser, bumper trims, front foglamp trims, parking brake lever trims, aluminium footrest, alloy wheels, wheel trims, chrome tailgate finisher, chrome tailpipe finisher, chrome mirror shells, chrome door handles...
* To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fit one mat on top of another.
Practical information
"Multimedia": bluetooth ® hands-free kit, support for bluetooth ®
hands-free kit, audio systems with steering controls interface, portable satellite navigation system, semi-integral portable navigation system carrier, mapping updates for integral navigation system, dVd player, auxiliary cable for connecting a portable MP3 player, USb box, Hi-Fi module, speakers, Wi-Fi on board, rear multimedia support, telephone/ smartphone support, 230 V socket, telephone charge compatible with iPhone...
by going to a CITRoËn dealer, you can also obtain cleaning and maintenance products
(interior and exterior) - including ecological products in the "TECHnaTURE" range - products for topping up (screenwash fluid...), touch up pens and paint aerosols for the exact colour of your vehicle, recharges (cartridge for the temporary puncture repair kit...), ...
Installation of radio communication transmitters
before installing any after-market radio communication transmitter, you can contact a CITRoËn dealer for the specification of transmitters which can be fitted (frequency, maximum power, aerial position, specific installation requirements), in line with the Vehicle
Electromagnetic Compatibility
Directive (2004/104/EC).
depending on the legislation in force in the country, certain safety equipment may be compulsory: high visibility safety vests, warning triangles, breathalyzers, spare bulbs, spare fuses, fire extinguisher, first aid kit, mud flaps at the rear of the vehicle.
The fitting of electrical equipment or accessories which are not recommended by CITRoËn may result in a failure of your vehicle's electronic system and excessive electrical consumption.
Contact a CITRoËn dealer for information on the range of recommended equipment and accessories.
11
183
Technical data
Petrol engines and gearboxes
Model codes:
SC...
ZMZ0 HMZ0
Engines
Gearboxes
Cubic capacity (cc) bore x stroke (mm)
Max power: EU standard (kW)*
Max power engine speed (rpm)
Max torque: EU standard (nm)
Max torque engine speed (rpm)
Fuel
Catalytic converter
OIL CAPACITIES (in litres)
Engine (with filter replacement)
VTi 68
Manual
(5-speed)
999
71 x 84.1
50
6 000
95
3 000
Unleaded
Yes
3.25
VTi 82
HMZ0/P
Manual
(5 speed)
Electronic
(5-speed)
1 199
75 x 90.5
60
5 750
118
2 750
Unleaded
Yes
3.25
HMZ6/PS e-VTi 82
Euro 6
Electronic
(5-speed)
1 199
75 x 90.5
60
5 750
118
2 750
Unleaded
Yes
3.25
8FP0/P
VTi 95
Electronic
(5-speed)
1 397
77 x 75
70
6 000
136
4 000
Unleaded
Yes
4.25
5FS0
VTi 120
4.25
5FS9
Manual
(5-speed) automatic
(4-speed)
1 598
77 x 85.8
88
6 000
160
4 250
Unleaded
Yes
184
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
Technical data
Petrol weights and towed loads (in kg)
Engines VTi 68 VTi 82
Gearboxes
Model codes:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % gradient
- Braked trailer (within GTW limit) on a 12 % gradient
- Braked trailer* (with load transfer within the
GTW limit)
- Unbraked trailer
- Recommended nose weight
Manual
ZMZ0
973
1 048
1 500
1 950
450
775
450
46
Manual
HMZ0
975
1 050
1 511
2 311
800
1 100
520
46
Electronic
HMZ0/P
1 060
1 135
1 515
2 315
800
1 100
520
46 e-VTi 82
Euro 6
Electronic
HMZ6/PS
980
1 055
1 541
2 341
500
800
500
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
12
185
186
Technical data
Petrol weights and towed loads (in kg)
Petrol engines VTi 95 VTi 120
Gearboxes
Model codes:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % gradient
- Braked trailer (within the GTW limit) on a 12 % gradient
- Braked trailer* (with load transfer within the
GTW limit)
- Unbraked trailer
- Recommended nose weight
Electronic
8FP0/P
1 079
1 154
1 581
2 481
900
1 150
570
46
Manual
5FS0
1 075
1 150
1 579
2 479
900
1 150
570
46
Automatic
5FS9
1 089
1 164
1 612
2 512
900
1 150
570
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
Technical data
LPG engine and gearbox
Model codes:
SC...
Engine
KFT0/GPL
KFT0/1GPL
1.4 i
Gearbox
Cubic capacity (cc) bore x stroke (mm)
Max. power: EU standard (kW)*
Max. power speed (rpm)
Max torque: EU standard (nm)
Max. torque speed (rpm)
Fuel
Manual
(5-speed)
1 360
75 x 77
51.5 / 54
5 200 / 5 200
115 / 118
3 300 / 3 300
LPG / Unleaded
Catalytic converter Yes
OIL CAPACITY (in litres)
Engine (with filter replacement)
3.0
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
For more information on the operation and use of your LPG vehicle, refer to the specific insert attached to the other vehicle documents.
12
187
188
Technical data
LPG weights and towed loads (in kg)
Engines 1.4 i
Gearboxe
Model codes:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % slope
- Braked trailer (within GTW limit) on a 12 % slope
- Braked trailer* (with load transfer within the
GTW limit)
- Unbraked trailer
- Recommended nose weight
Manual
KFT0/GPL
KFT0/1GPL
1 070
1 145
1 529
2 329
1 000
1 000
500
44
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning, towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
Technical data
diesel engines and gearboxes
Model codes:
SC...
8HR4
Engines HDi 70 PEF
8HP4/PS 9HK0 e-HDi 70 PEF HDi 75
Gearboxes
Cubic capacity (cc) bore x stroke (mm)
Max. power: EU standard (kW)*
Max. power engine speed (rpm)
Max. torque: EU standard (nm)
Max. torque engine speed (rpm)
Fuel
Catalytic converter
Particle emissions filter (PEF)
Manual
(5-speed)
1 398
73.7 x 82
50
4 000
160
1 750 diesel
Yes
Yes
Electronic
(5-speed)
1 398
73.7 x 82
50
4 000
160
1 750 diesel
Yes
Yes
Manual
(5-speed)
1 560
75 x 88.3
55
4 000
185
1 500 diesel
Yes no
OIL CAPACITIES (in litres)
Engine (with filter replacement) 3.75
3.75
3.75
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
12
.../S:
e-HDi model fitted with Stop & Start.
189
190
Technical data
diesel engines and gearboxes
Model codes:
SC...
9HJ0 9HP0 9HPK/S 9HP8/PS 9HR8/S
Engines HDi 90 HDi 90 PEF e-HDi 90 PEF e-HDi 115 PEF
Gearboxes
Cubic capacity (cc) bore x stroke (mm)
Max. power: EU standard (kW)*
Max. power engine speed (rpm)
Max. torque: EU standard (nm)
Max. torque speed (rpm)
Fuel
Catalytic converter
Particle emissions filter (PEF)
OIL CAPACITIES (in litres)
Engine (with filter replacement)
Manual
(5-speed)
1 560
75 x 88.3
68
4 000
230
1 750 diesel
Yes no
3.75
Manual
(5-speed)
1 560
75 x 88.3
68
4 000
230
1 750 diesel
Yes
Yes
3.75
Manual
(5-speed)
Electronic gearbox system
(6-speed)
1 560
75 x 88.3
68
4 000
230
1 750 diesel
Yes
Yes
3.75
3.75
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
Manual
(6-speed)
1 560
75 x 88.3
84
3 600
270
1 750 diesel
Yes
Yes
.../S
: e-HDi model fitted with Stop & Start.
Technical data
Diesel weights and towed loads (in kg)
Engines HDi 70 PEF e-HDi 70 PEF HDi 75
Gearboxes
Model codes:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % gradient
- Braked trailer (within GTW limit) on 12 % gradient
- Braked trailer* (with load transfer with the
GTW limit)
- Unbraked trailer
- Recommended nose weight
Manual
8HR4
1 070
1 145
1 581
2 281
700
950
570
46
Electronic
8HP4/PS
1 080
1 155
1 610
2 310
700
950
570
46
Manual
9HK0
1 118
1 193
1 592
2 492
900
1 150
570
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
12
191
192
Technical data
Diesel weights and towed loads (in kg)
Engines HDi 90 HDi 90 PEF e-HDi 90 PEF e-HDi 115 PEF
Gearboxes
Model codes:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % slope
- Braked trailer (within the GTW limit) on a 12 % slope
- Braked trailer* (with transfer of load within the GTW limit)
- Unbraked trailer
- Recommended nose weight
Manual
9HJ0
1 142
1 217
1 605
2 505
900
1 150
570
46
Manual
9HP0
1080
1155
1608
2508
900
1150
570
46
Manual
9HPK/S
1 085
1 160
1 625
2 525
900
1 150
570
46
Electronic
9HP8/PS
1 090
1 165
1 634
2 534
900
1 150
570
46
Manual
9HR8/S
1 090
1 165
1 648
2 548
900
1 150
570
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
dimensions (in mm)
Technical data
12
193
Technical data
Identification markings
Various visible markings for the identification of your vehicle.
D. Tyre/paint label.
This label is affixed to the left hand centre pillar.
It bears the following information:
- the tyre pressures, laden and unladen,
- the tyre sizes (including the load index and speed rating for the tyre),
- the tyre pressure for the spare wheel,
- the paint colour code.
194
A. Vehicle identification number (VIN) under the bonnet.
This number is engraved on the bodywork near the passenger compartment filter.
C. Manufacturer's label.
The VIn is indicated on a self-destroying label affixed to the left hand centre pillar.
B. Vehicle identification number on the dashboard.
This number is indicated on a self-adhesive label which is visible through the windscreen.
The tyre pressures must be checked when the tyres are cold, at least once a month.
Low tyre pressures increase fuel consumption.
EMERGENCY OR ASSISTANCE CALL
195
EMERGENCY OR ASSISTANCE CALL
CITROËN Localised Emergency Call CITROËN Localised Assistance Call
In an emergency, press this button for more than
2 seconds. Flashing of the green LED and a voice message confirm that the call has been made to the
CITRoËn Localised Emergency Call centre*.
Pressing this button again immediately cancels the call. The green LEd goes off.
Pressing this button (at any time) for more than 8 seconds cancels the call.
The green LED remains on (without flashing) when communication is established. It goes off at the end of communication.
This call is dealt with by the
CITRoËn Localised Emergency Call centre which receives locating information from the vehicle and can send a detailed alert to the appropriate emergency services. In countries in which the team is not operational, or when the locating service has been expressly declined, the call is dealt with directly by the emergency services (112) without the vehicle location.
If an impact is detected by the airbag control unit, and independently of the deployment of any airbags, an emergency call is made automatically.
If you benefit from the CITROËN eTouch offer, you also have available additional services in your MyCITRoËn personal space, via the CITRoËn
Internet website in your country, accessible on www.citroen.com.
* These services are subject to conditions and availability.
Consult a CITRoËn dealer.
196
Press this button for more than 2 seconds to request assistance if the vehicle breaks down.
A voice message confirms that the call has been made*.
Pressing this button again immediately cancels the request.
The cancellation is confirmed by a voice message.
Operation of the system
When the ignition is switched on, the green LEd comes on for 3 seconds indicating that the system is operating correctly.
If the orange LED flashes: there is a system fault.
If the orange LEd is on continuously: the backup battery must be replaced.
In either case, contact a CITRoËn dealer.
If you purchased your vehicle outside the CITROËN dealer network, we invite you to have a dealer check the configuration of these services and, if desired, modified to suit your wishes. In a multi-lingual country, configuration is possible in the official national language of your choice.
For technical reasons, particularly to improve the quality of Telematic services to customers, the manufacturer reserves the right to carry out updates to the vehicle's on-board telematic system.
The system is protected in such a way that it will only operate in your vehicle.
For safety reasons, the driver must only carry out operations which require prolonged attention while the vehicle is stationary.
When the engine is switched off and to prevent discharging of the battery, the system switches off following the activation of the energy economy mode.
eMyWay
SATELLITE NAVIGATION SYSTEM
MULTIMEDIA BLUETOOTH
TELEPHONE AUDIO SYSTEM
CONTENTS
01 First steps - Control panel
02 Steering mounted controls
03 General operation
04 Navigation - Guidance
05 Traffic information
06 Using the telephone
07 Radio
08 Music media players
09 Audio settings
10 Configuration
11 Screen menu map
Frequently asked questions p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
198
200
201
203
216
219
229
232
238
239
p.
240
p.
244
197
01 FIRST STEPS
Selection and confirmation OK knob:
Selection of an item on the screen or in a list or a menu, then confirmation with a short press.
other than for menus and lists, a short press displays a contextual menu depending on the current screen.
Rotation with map displayed: zoom the map scale in and out.
Short press without the engine running: on / off.
Short press with the engine running: audio source off / restore.
" open the
Configuration
" menu.
Long press: access to the GPS coverage and the navigation demonstration mode.
Select:
- the previous/next line in a list or menu.
- the previous / next media folder.
- step by step selection of the previous/ next radio frequency.
- the previous / next MP3 folder.
Move up/down, in "
Move the map " mode.
Volume adjustment (each source is independent, including Ta messages and navigation instructions).
MODE button: Selection of the type of permanent display.
Long press: black screen
(daRk).
access to the
" Navigation - guidance " menu and display the recent destinations.
open the "
Traffic information " menu and display the current traffic alerts.
abandon the current operation, up one level in the menu.
Long press: return to the permanent display.
Select:
- the next lower / higher radio frequency automatically.
- the previous / next Cd track,
MP3 track or media.
- the left / right of the screen when a menu is displayed.
Move left / right in " Move the map " mode.
198
01 FIRST STEPS access to the " RADIO " menu and display the list of stations received.
Long press: display the audio settings screen for the radio tuner source.
access to the " MUSIC " menu, and display of the Cd/MP3/ apple ® tracks and folders.
Long press: display the audio settings screen for the
" MEDIA " (Cd/USb/iPod/Streaming/aUX) sources.
open the " Telephone " menu and display the list of recent calls or accept an incoming call.
Continuous press: reinitialisation of the system.
Short press: select pre-set radio station.
Long press: pre-set the current station.
199
02 STEERING MOUNTED CONTROLS
RadIo: change to the next radio station in the list.
Long press: automatic search for a higher frequency.
Cd: select the next track.
CD: continuous press: fast forward play.
SRC/TEL button: change the audio source, start a call from the address book, call/end call on the telephone, press for more than 2 seconds: access to the address book.
RadIo: change to the previous radio station in the list.
Long press: automatic search for a lower frequency.
Cd: select the previous track.
Cd: continuous press: fast reverse.
RadIo: select the previous/next preset station.
Select the next entry in the address book.
Volume increase.
Mute: press the volume increase and decrease buttons simultaneously.
Restore the sound by pressing one of the two volume buttons.
Volume decrease.
200
03 GENERAL OPERATION
Press the MODE
button several times in succession for access to the following displays:
" RADIO "
" MAP IN WINDOW "
(If navigation guidance in progress)
" TELEPHONE "
(If conversation in progress)
" FULL SCREEN MAP "
SETUP: PaRaMETERS date and time, display configuration, sound, vehicle settings.
For cleaning the screen, the use of a soft, non-abrasive cloth
(spectacles cloth) is recommended, with no additional product.
Changing the audio source:
RADIO: RadIo broadcasts.
MUSIC: playing MUSIC.
For the details of the menus, refer to the "Screen menu map" section.
201
03 GENERAL OPERATION
Display according to context
202 a press on the knob gives access to short-cut menus according to the display in the screen.
RADIO:
1
Change waveband
2
FM
2
AM
1
Services announcements
2
Traffic announcements (TA)
2
Information
2
Entertainment
2
Special or Urgent
TELEPHONE (call in progress):
1
Private mode
1
Put call on hold
1
DTMF ring tones
1
Hang up
MUSIC MEDIA PLAYERS,
CD or USB (according to media):
Play modes:
1
Normal
1
Random
1
Random on all media
1
Repetition
1
FULL SCREEN MAP OR IN A
NEW WINDOW:
Stop / Restore guidance
1
Select destination
2
Enter an address
2
Directory
2
GPS coordinates
1
Divert route
1
Move the map
2
Info. on location
2
Select as destination
2
Select as stage
2
Save this place (contacts)
2
Quit map mode
1
Guidance criteria
04 NAVIGATION - GUIDANCE
Access to the "NAVIGATION" menu
" Navigation - guidance "
Press NAV .
a short press on the end of the lighting control stalk repeats the last navigation message.
List of recent destinations.
" Select destination "
" Journey leg and route "
" Guidance options "
" Map management "
" Stop / Restore guidance "
To make full use of all of the functions of your navigation system, update the mapping regularly. Contact a
CITRoËn dealer or order your mapping update at http://citroen.navigation.com
To delete the list of recent destinations, Select " Guidance options " in the navigation menu then Select " Delete last destinations
" and confirm. Select "
Yes
" then confirm.
deleting just one destination is not possible.
Go from the list to the menu (left/right).
or
203
204
04 NAVIGATION - GUIDANCE
Selecting a destination
Towards a new destination
Press NAV to display the
" Navigation - guidance " menu.
Select " Select destination " and confirm, then Select "
Enter an address " and confirm.
Select the " Country " function then confirm.
Selection the town from the list offered, then confirm.
A pre-set list (by entering the first few letters) of the towns in the country selected can be accessed directly by selecting and confirming "
List " in the screen.
If possible, enter the " Road " and " N°/X " information in the same way.
Select " Archive
" to save the address entered in a contact file.
After about 60 seconds with no address entered, the system returns to the last home page; to return to the current input, start again with steps 1 and 2 then press again to find the current input.
Select the " Town " or " Post code " function then confirm.
Select the letters in the name of the town or the characters in a post code one at a time, confirming each one with the knob.
Confirm "
OK " to start guidance.
Select the guidance criteria: " Fastest route ", " Shortest route " or optimised
" Distance/Time ", then select the
" desired restriction criteria: " With tolls ",
With Ferry confirm "
OK
", or "
".
Traffic info
" then
04 NAVIGATION - GUIDANCE
Towards a recent destination
Press NAV to display the
" Navigation - guidance " menu.
Select the desired destination and confirm to start guidance.
Delete recent destinations
Press NAV to display the
" Navigation - guidance " menu.
Select " Options
" and confirm and then
" Delete recent destinations " and confirm.
Towards a contact in the contacts directory
Navigation towards a contact is only possible if it has an address entered in the audio navigation system.
Press NAV to display the
" Navigation - guidance " menu.
Select " Select destination " and confirm, then Select "
Directory " and confirm.
Selection the desired destination from your contacts and confirm "
OK " to start the guidance.
205
206
04 NAVIGATION - GUIDANCE
Towards GPS coordinates
Press NAV to display the
" Navigation - guidance " menu.
Towards a point on the map
With the map displayed, press OK to display the contextual menu. Select
" Move the map
" and confirm.
Move the cursor using the control to identify the desired destination.
Select " Select destination " and confirm, then Select "
GPS coordinates " and confirm.
Enter the GPS coordinates and confirm
" OK " to start the guidance.
Press OK to display the contextual menu for " Move the map " mode.
Select " Select as destination " or
" Select as stage
" and confirm.
04 NAVIGATION - GUIDANCE
Towards points of interest (POI)
Press NAV to display the
" Navigation - guidance " menu.
The points of interest (PoI) indicate all of the service locations in the vicinity
(hotels, various businesses, airports...).
Select " Search by Name " to search for PoIs by name and not by proximity.
Select the " Enter an address " function and confirm, then select
Select destination
and confirm.
To select a PoI close to your current location, Select " POI
" and confirm, then
Select " Around the current place " and confirm.
To select a PoI as a stage on the route,
Select " POI
" and confirm, then Select
" On the route
" and confirm.
To select a PoI as a destination, first enter the country and town (see
"Towards a new destination"), Select
" POI
" and confirm, finally Select "
Near " and confirm.
Search for PoIs in the categories suggested in the following pages.
Select the POI and confirm "
OK " to start the guidance.
207
04 NAVIGATION - GUIDANCE
This icon appears when several POIs are grouped together in the same area. Zooming in on this icon shows details of the POIs.
List of principal points of interest (POI)
Service station airport
Garage
CITRoËn
Railway station bus station
Covered car park
Car park
Rest area
Port
Industrial estate
Supermarket
Hotel
Restaurant
Cafeteria bed and breakfast
Vending machine
Sports complex, sports centre, sports ground
Swimming pool
Winter sports resort
Cinema
Theme parks
Hospital, Chemist, Vet
Police station
School
Town hall
Post office
Museum, Culture, Theatre,
Historic monument
Tourist information, Tourist attraction
Risk areas / danger areas*
* according to availability in the country.
208
An annual mapping update allows new points of interest to be presented to you.
You can also update the Risk areas / danger areas every month.
The detailed procedure is available on: http://citroen.navigation.com.
04 NAVIGATION - GUIDANCE
Settings for risk area / danger area alerts
These functions are only available if risk areas have been downloaded and installed on the system.
The detailed procedure for updating risk area PoIs can be found at http://citroen.navigation.com.
Press NAV to display the " Navigation - guidance " menu.
Select " Guidance options
" and confirm, then Select " Set parameters for risk areas
" and confirm.
Select:
- "Visual alert"
- "audible alert"
- "alert only in guidance"
- "overspeed alarm only".
The choice of time of notification defines how long in advance that Risk area warnings are given.
Select " OK
" to confirm the screen.
209
210
04 NAVIGATION - GUIDANCE
Adding a stage Organising stages
Press NAV to display the
" Navigation - guidance " menu.
Select " Journey leg and route " then confirm.
Select " Add a stage
" then confirm
The address of the stage is entered as a destination, by " Enter an address ", a contact in " Directory ", or " Previous destinations ".
Select " Close to " a route passing close to the stage or " Strict " for a route passing through the stage.
Confirm "
OK " to start the guidance, and give a general indication of the guidance route.
To organise stages, carry out operations 1 to 2 again, then select
" order/delete journey legs " and confirm.
Select the stage that you want to move in the order.
Select and confirm to save the modifications.
Select " Delete " to delete the stage.
04 NAVIGATION - GUIDANCE
Route options
Calculation criteria
Press NAV to display the
" Navigation - guidance " menu.
Select " confirm.
Define calculation criteria
" and
This function allows modification of:
- the guidance criteria: (" Fastest route ", " Shortest route ",
" Distance/Time "),
- the exclusion criteria: (" With tolls " or " With Ferry "),
- traffic avoidance: (" Traffic info
").
If traffic avoidance (Traffic info) is selected, the system suggests an alternative route if there is a delay on the guidance route.
Select " Guidance options
" and confirm.
Select " OK
" and confirm to save the modifications.
211
212
04 NAVIGATION - GUIDANCE
Map management
Selecting the points of interest displayed on the map
Press NAV to display the
" Navigation - guidance " menu.
Select from the various categories the ones that you want to display on the screen.
Select " Map management
" and confirm.
Select " Map details
" and confirm.
Select " Default " to have only " Filling stations, garages " and
" Risk areas " appear on the map (if installed in the system).
Select " OK
" then confirm and select
" OK
" again then confirm to save the modifications.
04 NAVIGATION - GUIDANCE
Map orientation
Press NAV to display the
" Navigation - guidance " menu.
Select " Map management
" and confirm.
Select:
- " Vehicle direction " to have the map follow the direction of travel,
- " North direction " to keep the map always North up,
- " Perspective view " to display a perspective view.
The colour of the map, different from the day and night mode, is configured in the "
SETUP " menu.
Select " Map orientation
" and confirm.
Street names are visible on the map from the 100 m scale.
213
214
04 NAVIGATION - GUIDANCE
Navigation voice synthesis
Adjusting the volume / Deactivation
The volume of messages can be adjusted during the transmission of the message using the volume adjustment control.
The volume setting of guidance messages is also accessible via the " SETUP " / " Voice synthesis " menu.
Press NAV to display the
" Navigation - guidance " menu.
Select the volume graph and confirm.
adjust the volume to the desired level and confirm.
Select " Deactivate " to deactivate voice messages.
Select " Guidance options
" and confirm.
Select " Set speech synthesis " and confirm.
Select " OK " and press the dial to confirm.
04 NAVIGATION - GUIDANCE
Male voice / Female voice
Press SETUP to display the configuration menu.
Select " Voice synthesis
" and confirm.
Select " Select male voice " or " Select female voice
" then confirm "
Yes " to activate a male or female voice.
The system restarts.
215
216
05 TRAFFIC INFORMATION
Access to the "TRAFFIC INFORMATION" menu
"
Traffic information
"
Press " TRAFFIC ".
List of TMC messages in order of distance from the vehicle.
"
Geographic filter
"
" Select TMC station "
(automatic, manual)
" Display/Do not display messages "
Go from the list to the menu (left/right).
or
05 TRAFFIC INFORMATION
Configure the filtering and display of TMC messages
TMC (Traffic Message Channel) messages with GPS Navigation provide traffic information in real time.
Press the TRAFFIC button to display the
"
Traffic information
" menu.
The system offers a choice of:
- " Retain all the messages ", or
- " Retain the messages "
● "
Around the vehicle
", (confirm the mileage to modify and select the distance),
● "
On the route ".
Select the "
Geographic filter
" function
Confirm "
OK
" to save the modifications.
We recommend:
- a filter on the route and
- a filter around the vehicle of:
- 12 miles (20 km) in urban areas,
- 30 miles (50 km) on motorways.
217
218
05 TRAFFIC INFORMATION
Principal TMC symbols
black and blue triangle: general information, for example:
Weather reports
Wind
Parking
Traffic reports
Fog
Snow / ice
Receiving TA messages
The TA (Traffic Announcement) function gives priority to TA alert messages. To operate, this function needs good reception of a radio station transmitting this type of message. When a traffic report is transmitted, the current audio source (Radio, Cd, USb, ...) is interrupted automatically to play the Ta message. normal playback of the audio source resumes at the end of the transmission of the message.
Press RADIO to display the menu.
Red and yellow triangle: traffic information, for example:
Modified signage
Slippery surface delay
Risk of explosion demonstration no entry
Narrow carriageway accident
Roadworks
Road closed danger
Traffic jam
Select " Service announcements " then confirm.
activate or deactivate " TA
" then confirm.
The volume setting for Ta messages can be adjusted only during the transmission of this type of alert.
activate or deactivate the function at any time by pressing the button.
during a message, press the button to interrupt it.
06 USING THE TELEPHONE
Access to the "TELEPHONE" menu
Press this button.
List of recent calls sent and received with the telephone connected to the system.
To make a call, select a number in the list and confirm " to start the call.
OK "
" Telephone "
" Dial "
" Directory of contacts "
" Contacts management "
" Phone functions "
" Bluetooth functions "
" Hang up "
In the top bar of the permanent display no telephone connected.
Telephone connected.
Incoming call.
outgoing call.
Synchronisation of contacts in progress.
Telephone call in progress.
Go from the list to the menu (left/right).
or
Connecting a different telephone deletes the list of recent calls.
219
220
06 USING THE TELEPHONE
Pairing a Bluetooth telephone
First connection
You can check the compatibility of your telephone at www.citroen.co.uk (services).
For reasons of safety and because they require prolonged attention on the part of the driver, the operations for pairing the bluetooth mobile telephone to the hands-free system of the audio unit must be carried out with the vehicle stationary .
Procedure from the system
Quick procedure from the telephone activate the telephone's bluetooth function and ensure that it is "visible to all" (telephone configuration).
In the bluetooth menu of your telephone, select the name "CITRoËn" from the list of devices detected.
Press this button.
Enter a minimum 4 figure code in the telephone and confirm.
Enter the same code in the system, select " OK
" and confirm.
Select " Bluetooth functions " and confirm.
Select " Peripherals search " and confirm.
The list of peripheral devices detected is displayed. Wait until the " Connect " button is available.
06 USING THE TELEPHONE
The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used. Check the telephone manual and with your network provider for details of the services available to you.
Select the name of the desired peripheral from the list of devices detected then confirm
Enter a minimum 4 figure code in the telephone and confirm.
Select " Connect
" and confirm.
The system offers to connect the telephone:
- in " Hands-free mode " (telephone only),
- in " Audio " mode (streaming: playing music files on the telephone),
- or " All " (for selection of both modes).
Select " OK
" and confirm.
The " Hands-free mode " should be used in preference if
"Streaming" is not desired.
The ability of the system to connect in only one mode depends on the telephone. The two modes may both connect by default.
Enter the same code in the system, select " OK
" and confirm.
Then accept automatic connection on the telephone to allow the telephone to reconnect automatically every time the vehicle is started.
Depending on the type of telephone, the system will ask you to accept or not the transfer of your contacts.
on return to the vehicle,the last telephone connected automatically reconnects, within around 30 seconds after switching on the ignition (Bluetooth activated and visible).
To modify the automatic connection mode, remove the pairing and pair the telephone again with the desired mode.
221
222
06 USING THE TELEPHONE
Directory configuration / Synchronisation with the telephone
Press PHONE then Select " Contacts management
" and confirm.
Select " New contact
" to enter a new contact.
Select " Sort by Name/First name " or
" Sort by First name/Name " to choose the order in which they appear.
Select " Delete all contacts " to delete the contacts saved in the system.
Select " Import all the entries " to import all the contacts in the telephone and save them in the system.
once imported, a contact remains visible whatever telephone is connected.
Select " Synchronization options ":
- no synchronization: only the contacts saved in the system
(always present).
- display telephone contacts: only the contacts saved in the telephone.
- display SIM card contacts: only the contacts saved on the SIM card.
- display all phone contacts: contacts on the SIM card and in the telephone.
Select " Contact mem. status " to see the number of contacts saved in the system or imported, and the free memory.
06 USING THE TELEPHONE
Editing, importing or deleting a contact
Press PHONE then Select " Directory of contacts
" and confirm.
Select " Search ", then turn the knob to choose in numerical or alphabetical order a group of contacts from the entries made previously, then confirm.
Go to the list of contacts, select the desired contact then confirm.
Select " Open
" to view a contact on the telephone or modify a contact saved in the system.
Select " Import " to copy a contact from the telephone to the system.
Select " Delete " to delete a contact recorded in the system.
It is not possible to modify or delete contacts in the telephone or the
SIM card via the bluetooth connection.
once the contact has been imported, the bluetooth symbol disappears, replaced by the telephone symbol which shows that the contact has been saved in the system.
In the " Directory of contacts " menu, the import and deletion of contacts is done one by one.
Select OK or press the back button to exit this menu.
223
224
06 USING THE TELEPHONE
Making a call
Calling a new number
Use of the telephone is not recommended while driving. We recommended that you park safely or make use of the steering mounted controls.
Calling a contact
Press TEL
or twice on
PHONE .
Press PHONE
twice.
Select " Dial
" then confirm.
dial the telephone number using the virtual keypad selecting each number in turn.
Confirm "
OK " to make the call.
Select " Directory of contacts " then confirm.
Select the desired contact and confirm.
If access was via the
PHONE button,
Select " Call
" and confirm.
Select the number and confirm to start the call.
06 USING THE TELEPHONE
Ending a call
Calling a recently entered number
Press PHONE then select " OK " to end the call.
Press TEL , Select " Call list " and confirm, or
Press PHONE to display the calls log.
or make a long press on TEL at the steering mounted controls.
Or make two short presses on
TEL at the steering mounted controls.
Select the desired number and confirm.
To erase the calls log, press PHONE
twice, Select "
Phone functions
" and confirm then Select "
Delete calls log
" and confirm.
It is always possible to start a call directly from the telephone; park the vehicle as a safety measure.
or press the MODE button, as many times as necessary, until the telephone screen is displayed.
Press " OK " to display the contextual menu then Select " Hang up " and confirm.
225
226
06 USING THE TELEPHONE
Receiving a call
an incoming call is announced by a ring and a superimposed display on the screen.
" Yes " to accept the call is selected by default.
Press " OK " to accept the call.
Select " No
" and confirm to reject the call.
a short press on TEL accepts an incoming call.
a long press on TEL rejects an incoming call.
06 USING THE TELEPHONE
Options during a call*
during a call, press the MODE button several times to select display of the telephone screen, then press " OK " to open the contextual menu.
or make a short press on this button.
Select " Private mode
" and confirm to take the call on the handset.
or Select " Hands-free mode " and confirm to take the call via the vehicle's speakers.
Select " Put call on hold
" and confirm to put the current call on hold.
or Select " Resume the call " and confirm to resume the call on hold.
Select " DTMF ring tones " to use the numerical keypad, so as to navigate through the menu of an interactive vocal server.
Select " Hang up " to end the call.
it is possible to hold a 3-way conference call by making 2 calls in succession*.
Select " Conference mode call " in the contextual menu accessible using this button.
* depending on the compatibility of the phone and your service plan.
227
228
06 USING THE TELEPHONE
Managing paired telephones Changing the ringtone
Press PHONE
twice.
Select " Bluetooth functions ".
Select " List of the paired peripherals " and confirm.
It is possible to:
- " Connect " or " Disconnect " the selected telephone,
- delete the pairing of the selected telephone.
It is also possible to select all pairings.
Press PHONE
twice.
Select " Phone functions
" and confirm.
Select " Ring options
" and confirm.
You can adjust the volume and the type of ringtone.
Select " OK
" and confirm to save the changes.
07 RADIO
Access to the "RADIO" menu
Press RADIO .
" FM / AM band " alphabetical list of stations received.
" Change Waveband " (" AM / FM ")
" Guidance options " (" TA, RDS ")
" Audio settings " (see this section)
" Update radio list "
Press 5 or 6 or use the rotary control to select the previous or next station in the list.
Go from the list to the menu (left/right).
or
229
230
07 RADIO
Changing waveband Selecting a station
The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode.
This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.
The quality of reception is represented by the number of active waves in this symbol.
Press RADIO or OK to display the contextual menu.
By alphabetical list
Press RADIO , select the station of your choice and confirm.
Select " Change waveband ".
By automatic frequency search
Press 7 or 8 for the automatic search for a lower or higher radio frequency.
Or turn the thumb wheel at the steering mounted controls.
Select " AM / FM
" and confirm.
By manual frequency search
Press 5 or 6 to adjust the radio frequency step by step.
07 RADIO
Presetting a station
after selecting a station, press one of the buttons on the numerical keypad for 2 seconds to preset the current station.
An audible signal confirms that the station has been preset.
Press the button on the numerical keypad to recall a preset station.
Or press then turn the thumb wheel at the steering mounted controls.
Activate / Deactivate RDS
RDS, if activated, allows you to continue listening to the same station by automatic retuning to alternative frequencies. However, in certain conditions, coverage of an RdS station may not be assured throughout the entire country as radio stations do not cover 100 % of the territory. This explains the loss of reception of the station during a journey.
Press RADIO .
Select " Guidance options " then confirm.
activate or deactivate " RDS " then confirm.
231
232
08 MUSIC MEDIA PLAYERS
Access to the "MUSIC MEDIA PLAYER" menu
" MEDIA "
Press MUSIC .
List of the current media tracks.
" Change media "
" Eject USB device " (if USb connected)
" Play mode " (" Normal ",
" Random ", " Random on all media ", " Repetition ")
" Audio settings " (see this section)
" Activate / Deactivate AUX input "
Go from the list to the menu (left/right).
or
08 MUSIC MEDIA PLAYERS
CD, MP3 CD / USB player
Information and advice
The audio equipment will only play audio files with ".wma, .aac, .flac,. ogg and.mp3" file extensions and with a bit rate of between 32 Kbps and 320 Kbps.
It also supports VbR (Variable bit Rate) mode.
No other type of file (.mp4, .m3u...) can be played.
WMA files must be of the standard wma 9 type.
The sampling rates supported are greater than 32 KHz.
It is advisable to restrict file names to 20 characters, without using of special characters (e.g.: " " ? ; ù) to avoid any playing and displaying problems.
The system supports USb mass storage or iPod devices via the USb port (suitable cable not supplied).
If a partitioned USb memory key is connected to the system, only the first partition is recognised.
Control of the peripheral device is with the audio system controls.
The number of tracks is limited to 2000 maximum,
999 tracks per folder.
If the current consumption at the USb port exceeds
500 mA, the system goes into protection mode and deactivates the port.
other peripherals, not recognised on connection, must be connected to the auxiliary socket using a Jack cable
(not supplied).
In order to be able to play a recorded CDR or CDRW, when recording it is preferable to select the ISO 9660 level 1, 2 or Joliet standard.
If the disc is recorded in another format (udf, ...), it may not be played correctly.
It is recommended that the same recording standard is always used for an individual disc, with as low a speed as possible (4x maximum) for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is recommended.
Give preference to multimedia USb memory sticks (in general formatted FAT32 File Allocation Table).
The system does not support the operation of an apple ® a USb memory stick connected at the same time.
player and
It is recommended that official Apple
® USb cables are used to ensure correct operation.
233
234
08 MUSIC MEDIA PLAYERS
Sources
Insert the Cd in the player, insert the USb memory stick in the USb player or connect the
USb peripheral to the USb port using a suitable cable (not supplied).
The system builds playlists (in temporary memory), an operation which can take from a few seconds to several minutes at the first connection.
Reduce the number of non-music files and the number of folders to reduce the waiting time.
The playlists are updated every time the ignition is switched off or connection of a USB memory stick. However, the system memorises these lists and if they are not modified, the loading time will be shorter.
Play starts automatically after a period which depends on the capacity of the USb memory stick.
Selection of source
The SOURCE
button on the steering mounted controls allows a direct change to the next media source.
" CD / CD MP3 "
" RADIO "
" USB, iPod "
" STREAMING " " AUX "
Press MUSIC to display the " MEDIA " menu.
Select " Following media source " and confirm.
Repeat the operation as many times as necessary to obtain the desired media source (except for radio which is accessible either with
SOURCE or RADIO ).
08 MUSIC MEDIA PLAYERS
Selecting a track
Previous track.
next track.
Previous folder.
next folder.
Fast forward.
Fast backward.
Pause: long press on SRC .
Long press
Long press
/
/
/
/
MUSIC: List of USB or CD tracks or folders
Up or down in the list.
Confirm, next menu level.
Up one menu level.
/
/ /
/
+ /
/
235
08 MUSIC MEDIA PLAYERS
Connecting APPLE
®
players Audio streaming
Connect the apple ® player to the USb port using a suitable cable
(not supplied).
Play starts automatically.
Control is via the audio system.
236
The classifications available are those of the portable device connected (artists / albums / genres / playlists / audiobooks / podcasts).
The default classification used is by artist. To modify the classification used, return to the first level of the menu then select the desired classification (playlists for example) and confirm to go down through the menu to the desired track.
The "Shuffle tracks" mode on an iPod
® corresponds to the "Random" mode on the audio system.
The "Shuffle albums" mode on an iPod
® corresponds to the "Random all" on the audio system.
"Shuffle tracks" is restored by default on each connection.
The version of software in the audio system may not be compatible with the generation of your Apple
® player.
Streaming allows audio files on your telephone to be played via the vehicle's speakers.
Connect the telephone: see " USING THE TELEPHONE ".
Select " Audio " or " All
" profile.
If play does not start automatically, it may be necessary to start the audio playback from the telephone.
Control is from the peripheral device or by using the audio system buttons.
once connected in streaming mode, the telephone is considered to be a media source.
It is recommended that you activate " peripheral.
Repeat " on the bluetooth
08 MUSIC MEDIA PLAYERS
Using the auxiliary input (AUX)
JACK/USB audio cable not supplied
Connect the portable device
(MP3, WMa player…) to the
JACK auxiliary audio socket or
USb port using a suitable cable.
Select " Activate / Deactivate AUX input
" and confirm.
First adjust the volume of your portable device (to a high level). Then adjust the volume of your audio system.
Press MUSIC to display the " MUSIC " menu.
display and management of the controls are via the portable device.
237
09 AUDIO SETTINGS
They are accessible by the MUSIC button in the control panel or by a long press on RADIO according to the source in use.
The audio settings ( Equalizer , Bass , Treble and different and independent for each sound source.
Loudness ) are
The settings for distribution and balance are common to all sources.
238
- " Equalizer " (choice of 6 musical ambiences)
- " Bass "
- " Treble "
- " Loudness " (activate/deactivate)
- " Distribution " (" Driver ", " All passengers ")
- " Le-Ri balance " (Left/Right)
- " Fr-Re balance " (Front/Rear)
- " Auto. Volume " depending on road speed (activate/deactivate)
The distribution (or spatialisation using the arkamys number of listeners in the vehicle.
© system) of sound is an audio process that allows the audio quality to be adapted to the on-board audio: arkamys © Sound Staging.
With Sound Staging, the driver and passengers are immersed in an
"audio scene" recreating the natural atmosphere of an auditorium: truly a part of the scene and its surroundings.
This new sensation is made possible by software in the audio system which processes the digital signals from the media players (radio,
CD, MP3…) without changing the audio settings. This processing takes account of the characteristics of the passenger compartment to produce optimum results.
The arkamys ©
software installed in your audio system processes the digital signal from the media players (radio, Cd, MP3, ...) and recreates a natural musical scene, with harmonious placement of instruments and voices in the space in front of passengers, level with the windscreen.
10 CONFIGURATION
Display configuration
Press SETUP to display the
"
Configuration
" menu.
Select " confirm.
Display configuration
" and
Select " Choose colour
" and confirm to select the screen colour harmony and the map presentation mode:
- day mode,
- night mode,
- automatic day/night mode, according to whether the headlamps are on.
Select " Adjust luminosity
" and confirm to adjust the screen brightness.
Press " OK " to save the changes.
The settings for day and night are independent.
239
11 SCREEN MENU MAP(S)
MAIN FUNCTION
1
2
Option A
Option A1
3 option a11
1
Option B...
"Navigation - guidance"
MENU
1
Select destination
2
Enter an address
2
Directory
2
GPS coordinates
1
Journey leg and route
2
Add a stage
3
Enter an address
3 directory
3
Previous destinations
2
Order/delete journey legs
2
Divert route
2
Chosen destination
1
Guidance options
2
Define calculation criteria
3
Fastest route
3
Shortest route
3 distance/Time
3
With tolls
3
With Ferry
3
Traffic info
2
Set speech synthesis
2
Delete last destinations
2
Set parameters for risk areas
240
1
Map management
2
Map orientation
3
Vehicle direction
3
3 north direction
Perspective view
2
Map details
2
Move the map
2
Mapping and updating
2
Description of risk areas database
1
Stop / Restore guidance
2
Fastest route
2
Shortest route
2
Distance/Time
2
With tolls
2
With Ferry
2
Traffic info
11 SCREEN MENU MAP(S)
"TRAFFIC INFORMATION"
MENU
1
Geographic filter
2
Retain all the messages:
2
Retain the messages:
3 around the vehicle
3 on the route
1
Select TMC station
2
Automatic TMC
2
Manual TMC
2
List of TMC stations
1
Display / Do not display messages
"TELEPHONE" MENU
1
Dial
1
Directory of contacts
2
Call
2
Open
2
Import
2
Search
2
Delete
1
2
Cancel
Contacts management
2
New contact
2
Sort by First name/Name
2
Delete all contacts
2
Import all the entries
2
Synchronization options
3 no synchronization
3 display telephone contacts
3 display SIM card contacts
3 display all phone contacts
2
Contact mem. status
1
Phone functions
2
Ring options
1
2
Delete calls log
Bluetooth functions
2
List of the paired peripherals
3
Connect
3 disconnect
3 delete
1
2
3 delete all
2
3
Cancel
Peripherals search
Rename radiotelephone
Hang up
241
11 SCREEN MENU MAP(S)
"RADIO" MENU
1
Change Waveband
2
FM
2
AM
1
Options
2
RDS station tracking
1
Audio settings
2
Equalizer
3 none
3
Classical
3
Jazz
3
Rock
3
Techno
3
Vocal
2
Bass
2
Treble
2
Loudness
3 activated / deactivated
2
Distribution
3 driver
3 all passengers
2
Le-Ri balance
2
Fr-Re balance
2
Auto. Volume
3 activated / deactivated
1
Update radio list
242
"MUSIC" MENU
1
Change Media
2
CD
2
Bluetooth streaming
2
USB/iPod
2
AUX
1
Read mode
2
Normal
2
Random
2
Random on all media
2
Repetition
1
Audio settings
1
Activate / Deactivate AUX input
11 SCREEN MENU MAP(S)
"SETUP" MENU
1
Display configuration
2
Choose colour
3
Harmony:
3
Cartography:
4 day mode
4 night mode
4 auto day/night
2
Adjust luminosity
2
Set date and time
2
Select units
1
Speech synthesis setting
2
Guidance instructions volume
2
Select male voice/Select female voice
1
Select language
2
Français
2
English
2
Italiano
2
Portuguese
2
Español
2
Deutsch
2
Nederlands
2
Turkçe
2
2
Polski
Русский
2
Cestina
2
Hrvatski
2
Magyar
1
1
Define vehicle parameters*
Trip computer
2
Alert log
2
Status of functions
* The settings vary according to the vehicle.
243
FREQUENTLY ASKED QUESTIONS
The following table groups together the answers to the most frequently asked questions concerning your audio system.
QUESTION
The route calculation is not successful.
ANSWER
The guidance criteria may conflict with the current location (exclusion of toll roads on a toll motorway).
SOLUTION
Check the guidance criteria on the navigation
Menu, "Guidance options"\ "define calculation criteria".
I am unable to enter my post code.
The system only accepts post codes of up to 7 characters.
The PoIs do not appear.
The PoIs have not been selected.
Select the PoIs in the list of PoIs.
The risk areas audible warning does not work.
The audible warning is not active.
Activate audible warnings in the Guidance options menu, "navigation - guidance", "Set parameters for risk areas".
Select the "Traffic info" function in the list of guidance criteria.
The system does not suggest a detour around an incident on the route.
The guidance criteria do not take account of TMC messages.
I receive a Risk area alert which is not on my route.
other than guidance, the system announces all Risk areas positioned in a cone located in front of the vehicle. It may provide an alert for a Risk area located on nearby or parallel roads.
Zoom in on the map to view the exact position of the Risk area. Select "on the route" to no longer receive alerts other than guidance or to reduce the time for the announcement.
244
FREQUENTLY ASKED QUESTIONS
QUESTION
Certain traffic jams along the route are not indicated in real time.
ANSWER on starting, it is several minutes before the system begins to receive the traffic information.
The filters are too restrictive.
SOLUTION
Wait until the traffic information is being received correctly (display of the traffic information icons on the map).
Modify the "Geographic filter" settings.
The altitude is not displayed.
I am unable to connect my bluetooth telephone.
The volume of the telephone connected in bluetooth mode is inaudible.
In certain countries, only major routes (motorways...) are listed for the traffic information.
This phenomenon is normal. The system is dependent on the traffic information available.
on starting, the initialisation of the GPS may take up to 3 minutes to receive more than 4 satellites correctly.
Depending on the geographical environment (tunnel...) or the weather, the conditions of reception of the GPS signal may vary.
The telephone's Bluetooth function may be switched off or the telephone may not be visible.
The Bluetooth telephone is not compatible with the system.
The volume depends both on the system and on the telephone.
The ambient noise level has an influence on the quality of telephone communication.
Wait until the system has started up completely.
Check that there is a GPS coverage of at least
4 satellites (long press on the SETUP button, then select "GPS coverage").
This phenomenon is normal. The system is dependent on the GPS signal reception conditions.
- Check that your telephone's bluetooth function is switched on.
- Check in the telephone settings that it is
"visible to all".
You can check the compatibility of your telephone on www.citroen.co.uk (services)
Increase the volume of the audio system, to maximum if required, and increase the volume of the telephone if necessary.
Reduce the ambient noise level (close the windows, reduce the booster fan speed, slow down, ...).
245
FREQUENTLY ASKED QUESTIONS
QUESTION
Some contacts are duplicated in the list.
ANSWER
The options for synchronizing contacts are synchronizing the contacts on the SIM card, the contacts on the telephone, or both . When both synchronizations are selected, some contacts may be duplicated.
Contacts are not shown in alphabetical order.
Some telephones offer display options. depending on the settings chosen, contacts can be transferred in a specific order.
SOLUTION
Select "display SIM card contacts" or "display telephone contacts".
Modify the display setting in the telephone directory.
The system does not receive
SMS text messages.
The Cd is ejected automatically or is not played by the player.
The bluetooth mode does not permit sending SMS text messages to the system.
The CD is inserted upside down, is unplayable, does not contain any audio data or contains an audio format which the player cannot play.
The CD has been recorded in a format that is not compatible with the player (udf, ...).
The CD is protected by an anti-pirating protection system which is not recognised by the audio system.
- Check that the Cd is inserted in the player the right way up.
- Check the condition of the Cd: the Cd cannot be played if it is too damaged.
- Check the content in the case of a recorded
Cd: refer to the information and advice in the
"MUSIC MEdIa PLaYERS" section.
- The audio system's Cd player does not play dVds.
- Some recorded CDs will not be played by the audio system because they are not of the correct quality.
This phenomenon is normal.
There is a long waiting period following the insertion of a Cd or connection of a
USb memory stick.
When a new medium is inserted, the system reads a certain amount of data (directory, title, artist, etc.). This may take from a few seconds to a few minutes.
The Cd player sound is poor.
The Cd used is scratched or of poor quality.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
Insert good quality Cds and store them in suitable conditions.
Set the treble or bass level to 0, without selecting an ambience.
246
FREQUENTLY ASKED QUESTIONS
QUESTION ANSWER
Some characters in the media information are not displayed correctly while playing.
The audio system does not display some types of characters.
SOLUTION
Use standard characters to name tracks and folders.
Playing of streaming files does not start.
The peripheral device connected does not support automatic play.
The names of tracks and the track length are not displayed on the screen when streaming audio.
The Bluetooth profile does not allow the transfer of this information.
The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function
(no sound, 87.5 Mhz is displayed...).
The vehicle is too far from the transmitter used by the station listened to or there is no transmitter in the geographical area through which the vehicle is travelling.
The environment (hills, buildings, tunnels, basement car parks...) block reception, including in RdS mode.
The aerial is absent or has been damaged (for example when going through a car wash or into an underground car park).
I cannot find some radio stations in the list of stations received.
The station is not received or its name has changed in the list.
The name of the radio station changes.
Some radio stations send other information in place of their name
(the title of the song for example).
The system interprets this information as the name of the station.
Start the playback from the device.
activate the "RdS" function by means of the short-cut menu to enable the system to check whether there is a more powerful transmitter in the geographical area.
This phenomenon is normal and does not indicate a fault with the audio system.
Have the aerial checked by a CITRoËn dealer.
247
FREQUENTLY ASKED QUESTIONS
QUESTION
In changing the setting of treble and bass the equalizer setting is deselected.
In changing the equalizer setting, treble and bass return to zero.
ANSWER
The selection of an equalizer setting imposes the balance settings.
Modifying one without the other is not possible.
SOLUTION
Modify the balance or equalizer settings to obtain the desired musical ambience.
When changing the balance settings, the distribution setting is deselected.
When changing an distribution setting, the balance setting is deselected.
There is a difference in sound quality between the different audio sources (radio, Cd...).
The selection of a distribution setting imposes the balance settings.
Modifying one without the other is not possible.
Modify the balance or distribution settings to obtain the desired musical ambience.
For optimum sound quality, the audio settings for Volume, bass, Treble,
Equalizer and Loudness can be adapted to the different sound sources, which may result in audible differences when changing source (radio,
Cd...).
Check that the audio settings for (Volume, bass,
Treble, Equalizer, Loudness) are adapted to the sources listened to. It is advisable to set the aUdIo functions (bass, Treble, Fr-Re balance,
Le-Ri balance) to the middle position, select the
"none", musical ambience and set the loudness correction to the "active" position in Cd mode or to the "Inactive" position in radio mode.
248
FREQUENTLY ASKED QUESTIONS
QUESTION
With the engine off, the system switches off after a few minutes of use.
ANSWER
When the engine is switched off, the system's operating time depends on the battery charge.
The switch-off is normal: the system switches to economy mode and switches off to prevent discharging of the vehicle's battery.
SOLUTION
Start the vehicle's engine to increase the battery charge.
Playback of my USb memory stick starts only after a very long wait
(around 2 to 3 minutes).
Some files supplied with the memory stick may greatly slow down access to reading the memory stick (multiplication by 10 of the catalogue time).
Delete the files supplied with the memory stick and limit the number of sub-folders in the file structure on the memory stick.
When I connect my iPhone as telephone and to the USb port at the same time, I am unable to play the music files.
When the iPhone connects automatically as a telephone, it forces the streaming function. The streaming function takes the place of the USb function which is then not useable, there is a period without sound of the track being played with Apple
® players.
disconnect and reconnect to the USb port
(the USb function takes priority over streaming).
249
250
Audio system
AUDIO SYSTEM / BLUETOOTH
®
Your Audio system is coded in such a way that it will only operate in your vehicle.
For safety reasons, the driver must only carry out operations which require prolonged attention while the vehicle is stationary.
When the engine is switched off and to prevent discharging of the battery, the audio equipment may switch off after a few minutes.
CONTENTS
01 First steps
02 Steering mounted controls
03 Main menu
04 Audio
05 USB Box
06 Bluetooth functions
07 Screen menu map(s)
Frequently asked questions p.
p.
p.
p.
p.
p.
p.
p.
252
253
254
255
258
261
264
269
251
01 FIRST STEPS
Select source: radio, audio Cd / MP3 Cd, USb,
Jack connection, Streaming, aUX.
Selection of aM / FM wavebands.
Eject Cd.
audio settings: front/ rear fader, left/right balance, bass/treble, loudness, audio ambiences.
display the list of local stations.
Long press: Cd tracks or MP3 folders (Cd / USb).
abandon the current operation.
TA (Traffic Announcements) on/off.
Long press: PTY* (radio
Programme TYpe) mode.
Select the screen display mode: date, audio functions, trip computer, telephone.
automatic frequency search down/up.
Select previous/next Cd, MP3 or USb track.
on/off, volume setting.
The daRk button changes the screen display for improved driving comfort at night.
1 st press: upper bar only illuminated.
2 nd press: black screen.
3 rd press: return to standard display.
buttons 1 to 6:
Select a pre-set radio station.
Long press: pre-set a station.
Confirm.
display main menu.
Select next frequency down/up.
Select previous/next MP3 folder.
Select previous/next folder / genre / artist / playlist (USb).
* available according to version.
252
02 STEERING MOUNTED CONTROLS
Radio: automatic search for a higher frequency.
Cd / MP3 / USb: selection of the next track.
CD / USB: continuous press: fast forwards play.
Move in the list.
Change audio source.
Confirm a selection.
Call/end call on the telephone.
Press for more than 2 seconds: telephone main menu.
Radio: automatic search for a lower frequency.
Cd / MP3 / USb: selection of the previous track.
Cd / USb: continuous press: fast reverse.
Move in the list.
Radio: select the previous/next pre-set station.
USb: select genre / artist / folder from the classification list.
Select the previous/next item in a menu.
Volume increase.
Mute: press the volume increase and decrease buttons simultaneously.
The sound is restored by pressing one of the two volume buttons.
Volume decrease.
253
254
03 MAIN MENU
AUDIO FUNCTIONS : radio, Cd, USb, options.
Screen C
TELEPHONE : bluetooth hands-free, pairing, management of a call.
TRIP COMPUTER : entering of distances, alerts, status of functions.
PERSONALISATION-
CONFIGURATION : vehicle parameters, display, languages.
Screen A
For a detailed global view of the menus available, refer to the
"Screen menu map" section.
04 AUDIO
Radio
Selecting a station
Press the SoURCE button several times in succession and select the radio.
Press the band aST button to select a waveband: FM1, FM2, FMast, AM.
Briefly press one of the buttons to carry out an automatic search of the radio stations.
Press one of the buttons to carry out a manual search up / down for radio frequencies.
Press the LIST REFRESH button to display the list of stations received locally (30 stations maximum).
To update this list, press for more than two seconds.
The external environment (hills, buildings, tunnels, basement car parks, ...) may block reception, including in RdS mode. This is a normal effect of the way in which radio waves are transmitted and does not indicate any failure of the audio system.
RDS
Press the MEnU button.
Select aUdIo FUnCTIonS then press ok.
Select the FM WaVEband
PREFEREnCES function then press ok.
Select aCTIVaTE RdS then press ok. RdS appears on the screen.
In radio mode, press ok directly to activate / deactivate RdS mode.
The RdS, if displayed, enables you to continue listening to the same station by automatic retuning to alternative frequencies. However, in certain conditions, coverage of an RdS station may not be assured throughout the country as radio stations do not cover 100% of the territory. Under conditions of very weak reception, the system may change to a regional station.
255
256
04 AUDIO
Receiving TA messages
The TA (Traffic Announcement) function gives priority to TA alert messages. To operate, this function needs good reception of a radio station transmitting this type of message. When a traffic report is transmitted, the current audio source (Radio, Cd, ...) is interrupted automatically to play the Ta message. normal playback of the audio source resumes at the end of the transmission of the message.
Press the Ta button to activate or deactivate traffic messages.
CD
Playing a CD
Insert circular compact discs only.
Some anti-pirating systems, on original discs or Cds copied using a personal recorder, may cause faults which are no reflection on the quality of the vehicle's player.
Without pressing the EJECT button, insert a CD in the player, play begins automatically.
To play a disc which has already been inserted, press the SoURCE button several times in succession and select Cd.
Press one of the buttons to select a track on the Cd.
Press the LIST REFRESH button to display the list of tracks on the Cd.
Press and hold one of the buttons for fast forwards or fast backwards.
04 AUDIO
MP3 CD
Playing an MP3 compilation
Insert an MP3 compilation in the player.
The audio equipment searches for all of the music tracks, which may take anything between a few seconds and several tens of seconds, before play begins.
On a single disc, the CD player can read up to 255 MP3 files spread over 8 folder levels. However, it is advisable to keep to a limit of two levels to reduce the access time before the CD is played.
While the CD is being played, the folder structure is not followed.
All of the files are displayed on a single level.
To play a disc which has already been inserted, press the SoURCE button several times in succession and select Cd.
Press one of the buttons to select a folder on the Cd.
Press one of the buttons to select a track on the Cd.
Press the LIST REFRESH button to display the list of directories of the MP3 compilation.
Press and hold one of the buttons for fast forward or backward play.
MP3 CD
Information and advice
The MP3 format, an abbreviation of MPEG 1.2 & 2.5 Audio Layer 3, is an audio compression standard which permits the recording of several tens of music files on a single disc.
In order to be able to play a recorded CDR or CDRW, when recording, the ISO 9660 level 1.2 or Joliet file format is recommended.
If the disc is recorded in another format, it may not be played correctly.
It is recommended that the same recording format is always used for an individual disc, with as low a speed as possible
(4x maximum) for optimum sound quality.
In the particular case of a multi-session CD, the Joliet format is recommended.
The audio system will only play files with the extension ".mp3" with a sampling rate of 22.05 KHz or 44.1 KHz. No other type of file
(.wma, .mp4, .m3u...) can be played.
It is advisable to restrict file names to 20 characters without using special characters (e.g. " ? ; ù) to avoid any playing or displaying problems.
Empty Cds are not recognised and may damage the system.
257
05 USB PLAYER
Using the USB BOX
258
This unit consists of a USb port and an auxiliary
Jack socket*. The audio files are transmitted from a portable device - digital player or a USb memory stick - to your audio system and heard via the vehicle's speakers.
USb memory stick or apple ® generation 5 or later:
player of
- Give preference to multimedia USb memory sticks (in general formatted FAT 32 File allocation Table),
- the apple ® player lead is essential,
- navigation through the file database is also possible by means of the steering mounted controls.
other apple ® players of earlier generations and players using the MTP protocol*:
- play via Jack-Jack lead only (not supplied),
- navigation through the file database is from the portable device.
Connecting a USB memory stick
Connect the memory stick to the port, directly or using a lead. If the audio equipment is switched on, the USb source is detected as soon as it is connected. Play begins automatically after a delay which depends on the capacity of the USB memory stick.
The file formats supported are .mp3 (mpeg1 layer 3 only) and .wma (standard 9 only,
128 kbits/sec compression).
Certain playlist formats are supported (.m3u, ...) on reconnection of the previous memory stick used, play is resumed automatically with the last track played.
The system puts together playlists (temporary memory) created over a period which depends on the capacity of the USB device.
The other sources are available during this time.
The playlists are updated each time the ignition is switched off or each time a USb memory stick is connected.
When connecting for the first time, the classification suggested is by folder. When you reconnect, the classification selected previously is retained.
* depending on vehicle.
05 USB PLAYER
Using the USB PORT
Press and hold LIST to display the different classifications.
Select by Folder / artist / Genre / Playlist, press OK to select the classification required, then press OK again to confirm.
- by Folder: all folders containing audio files recognised on the peripheral device.
- by artist: all of the artist names defined in the ID3 Tags, classified in alphabetical order.
- by Genre: all of the genres defined in the Id3 Tags.
- by Playlist: in accordance with the playlists recorded on the USb device.
Press LIST briefly to display the previously selected classification.
navigate through the list using the left/ right and up/down buttons.
Confirm the selection by pressing OK.
Press one of these buttons to gain access to the previous / next track on the classification list currently being played.
Press and hold one of the buttons for fast forward or backward play.
Press one of these buttons to gain access to the previous / next
Genre, Folder, artist or Playlist on the classification list currently being played.
Connecting an Apple ® player via the USB port
The lists available are Artist, Genre and Playlist (as defined in the apple ® player).
Selection and navigation are described in steps 1 to 4 above.
do not connect a hard disk or USb connection device other than audio equipment to the USb port. This could damage your installation.
259
260
05 USB PLAYER
Using the auxiliary input (AUX)
JACK socket or USB port (according to vehicle)
The auxiliary input, JACK or USB, allows the connection of a portable device (MP3 player...).
Do not connect a device to both the JACK socket and the USB port at the same time.
Connect the portable device (MP3 player…) to the JACK socket or to the USb port, using a suitable cable
(not supplied).
Adjusting the volume of the auxiliary source
First adjust the volume of your portable device.
Then adjust the volume of your audio system.
The display and control is via the portable device.
Press the SoURCE button several times in succession and select aUX.
06 BLUETOOTH FUNCTIONS
Bluetooth telephone
Screen C
(Available according to model and version)
The services offered depend on the network, the SIM card and the compatibility of the bluetooth equipment used.
Consult your telephone's manual and your operator to find out which services are available to you.
Pairing a telephone / First connection
For safety reasons and because they require prolonged attention on the part of the driver, the operations for pairing of the bluetooth mobile telephone with the Bluetooth hands-free system of your audio equipment must be carried out with the vehicle stationary and the ignition on.
Go to www.citroen.co.uk for more information (compatibility, more help, ...).
activate the telephone's bluetooth function and ensure that it is "visible to all" (telephone configuration).
The first 4 telephones recognised are displayed in this window.
The TELEPHONE menu permits access to the following functions in particular: directory*, Call list, Pairing management.
* If your telephone is fully compatible.
Select the telephone to be connected from the list. only one telephone can be connected at a time.
Press the MEnU button.
In the menu, select:
- bluetooth telephone function - audio
- Bluetooth configuration
- Perform a bluetooth search
A window is displayed with a message that a search is in progress.
a virtual keypad is displayed in the screen: enter a code with at least 4 digits.
Confirm by pressing OK.
a message is displayed in the screen of the telephone chosen. To accept the pairing, enter the same code on the telephone, then confirm with OK.
If pairing fails, the number of attempts is not limited.
a message that the pairing has been successful appears in the screen.
The automatic connection authorised is only active after the telephone has been configured.
The directory and the call list can be accessed after the synchronisation period.
261
06 BLUETOOTH FUNCTIONS
262
Receiving a call an incoming call is announced by a ring and a superimposed display in the vehicle's screen.
Select the YES tab on the display using the buttons and confirm by pressing ok.
Press this button to accept the call.
Making a call
From the bluetooth telephone function audio menu, select Manage the telephone call then Call, Call list or directory.
Press this button for more than two seconds for access to your directory, then navigate with the thumb wheel.
or
To dial a number, use your telephone's keypad, with the vehicle stationary.
The system accesses the telephone's contacts directory, depending on compatibility, and while the Bluetooth connection with it is maintained.
With certain telephones connected by bluetooth you can send a contact to the directory of the audio system.
Contacts imported in this way are saved in a permanent directory visible to all, whatever the telephone connected.
The menu for the directory is not accessible if it is empty.
06 BLUETOOTH FUNCTIONS
Ending a call during a call, press this button for more than
2 seconds.
Confirm with OK to end the call.
Bluetooth audio streaming*
Wireless transmission of music files on the telephone, played via the audio equipment. The telephone must be able to manage the appropriate Bluetooth profiles (Profiles A2DP / AVRCP).
Initiate the pairing between the telephone and the vehicle. This pairing can be initiated from the vehicle's telephone function menu or via the telephone's keypad. Refer to the steps in "Pairing a telephone" on the previous pages. during the pairing phase, the vehicle must be stationary with the key in the ignition.
Select the telephone to be connected from the telephone function menu.
The audio system connects to a newly paired telephone automatically.
activate the streaming source by pressing the SoURCE button**.
The tracks to be played can be controlled as usual via the buttons on the audio system control panel and the steering mounted controls***.
The contextual information can be displayed on the screen.
* depending on the compatibility of the telephone.
** In certain cases, playing of the Audio files must be initiated from the keypad.
*** If the telephone supports the function.
263
264
07 SCREEN MENU MAP(S)
Screen A
MAIN FUNCTION
1
2
Option A
Option A1
3 option a11
1
Option B...
1
Radio-CD
2
RDS options
2
REG mode
2
CD repeat
2
Shuffle play
1
Vehicle config*
2
R wiper in rev
2
Guide lighting
* The settings vary according to vehicle.
1
Options
2
Diagnostic
3
View
3 abandon
07 SCREEN MENU MAP(S)
1
Units
2
Temperature: °Celsius / °Fahrenheit
2
Fuel consumption:
KM/L - L/100 - MPG
1
Display adjust
2
Year
2
Month
2
Day
2
Hour
2
Minutes
2
12 H/24 H mode
1
Language
2
Français
2
Italiano
2
Nederlands
2
Portuguès
2
Portuguès-Brasil
2
Deutsch
2
English
2
Español
2
Cestina
2
Hrvatski
2
Magyar
265
266
07 SCREEN MENU MAP(S)
Screen C Press the ok dial for access to short-cut menus according to the display on the screen:
RADIO
1 activate / deactivate RDS
1 activate / deactivate REG mode
1 activate / deactivate radiotext
CD / MP3 CD
1 activate / deactivate Intro
1 activate / deactivate track repeat
(the entire current CD for CD, the entire current folder for MP3 CD)
USB
1 activate / deactivate track repeat (of the current folder / artist / genre / playlist)
1 activate / deactivate random play
(the entire current CD for CD, the entire current folder for MP3 CD)
1 activate / deactivate random play (of the current folder / artist / genre / playlist)
07 SCREEN MENU MAP(S)
Screen C
Pressing the MEnU button displays:
1
Audio functions
2
FM preferences
3 alternative frequencies (RdS)
4 activate / deactivate
3
Regional mode (REG)
4 activate / deactivate
3
Radio-text information (RdTXT)
4 activate / deactivate
2
Play modes
3 album repeat (RPT)
4 activate / deactivate
3
Track random play (RdM)
4 activate / deactivate
1
Trip computer
2
Enter distance to destination
3 distance: x miles
2
Alert log
3 diagnostics
2
State of systems *
3
Systems activated or deactivated
* The settings vary according to vehicle.
267
07 SCREEN MENU MAP(S)
1
Personalisation-Configuration
2
Define vehicle settings
*
2
Display configuration
3
Video-brightness adjustment
4 normal video
4 inverse video
4 brightness (- +) adjustment
3
Setting the date and time
4 setting day/month/year
4 hour/minute adjustment
4 choice of 12 h / 24 h mode
3
Choice of units
4 l/100 km - mpg - km/l
4
°Celsius / °Fahrenheit
2
Choice of language
268
1
Bluetooth telephone
2
Bluetooth configuration
3
Connect/disconnect an equipment
3
Telephone function
3 audio Streaming function
4
Consult the paired equipment
4 delete a paired equipment
4
Perform a bluetooth search
2
Call
3
Calls list
4 directory
2
Manage the telephone call
3
Terminate the current call
3 activate secret mode
* The settings vary according to vehicle.
FREQUENTLY ASKED QUESTIONS
QUESTION
There is a difference in sound quality between the different audio sources (radio, Cd...).
ANSWER
For optimum sound quality, the audio settings (Volume, bass, Treble, ambience, Loudness) can be adapted to the different sound sources, which may result in audible differences when changing source (radio,
Cd...).
SOLUTION
Check that the audio settings (Volume, bass,
Treble, ambience, Loudness) are adapted to the sources listened to. It is advisable to set the aUdIo functions (bass, Treble, Front-Rear balance, Left-Right balance) to the middle position, select the musical ambience "none" and set the loudness correction to the "active" position in Cd mode or to the "Inactive" position in radio mode.
The Cd is ejected automatically or is not played by the player.
The CD is inserted upside down, is unplayable, does not contain any audio data or contains an audio format which the player cannot play.
The CD is protected by an anti-pirating protection system which is not recognised by the audio equipment.
- Check that the Cd is inserted in the player the right way up.
- Check the condition of the Cd: the Cd cannot be played if it is too damaged.
- Check the content in the case of a recorded
Cd: consult the advice in the "audio" section.
- The audio equipment's Cd player does not play dVds.
- Due to their quality level, certain writeable
CDs will not be played by the audio system.
The message "USb peripheral error" is displayed on the screen.
The bluetooth connection is cut.
The battery of the peripheral may not be sufficiently charged.
The USb memory stick is not recognised.
The memory stick may be corrupt.
Recharge the battery of the peripheral device.
Reformat the memory stick.
269
FREQUENTLY ASKED QUESTIONS
QUESTION ANSWER
I am unable to access my voicemail.
Few telephones or service providers allow the use of this function.
SOLUTION
The Cd player sound is poor.
The Cd used is scratched or of poor quality.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
The stored stations do not function (no sound,
87.5 Mhz is displayed...).
An incorrect waveband is selected.
Insert good quality Cds and store them in suitable conditions.
Set the treble or bass level to 0, without selecting an ambience.
Press the band aST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored.
The traffic announcement
(Ta) is displayed. I do not receive any traffic information.
The radio station is not part of the regional traffic information network.
The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function
(no sound, 87.5 Mhz is displayed...).
The vehicle is too far from the transmitter used by the station listened to or there is no transmitter in the geographical area through which the vehicle is travelling.
The environment (hills, buildings, tunnels, basement car parks...) block reception, including in RdS mode.
The aerial is absent or has been damaged (for example when going through a car wash or into an underground car park).
270
Tune to a radio station which broadcasts traffic information.
activate the RdS function to enable the system to check whether there is a more powerful transmitter in the geographical area.
This phenomenon is normal and does not indicate a failure of the audio equipment.
Have the aerial checked by a CITRoËn dealer.
FREQUENTLY ASKED QUESTIONS
QUESTION ANSWER
Sound cut-outs of 1 to
2 seconds in radio mode.
during this brief sound cut-out, the RdS searches for any frequency permitting better reception of the station.
SOLUTION deactivate the RdS function if the phenomenon is too frequent and always on the same route.
With the engine off, the audio equipment switches off after a few minutes of use.
When the engine is switched off, the audio equipment operating time depends on the battery charge.
The switch-off is normal: the audio equipment switches to economy mode and switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery charge.
The message "the audio system is overheated" appears on the display.
In order to protect the installation if the surrounding temperature is too high, the audio equipment switches to an automatic thermal protection mode leading to a reduction of the volume or stopping of the playing of the Cd.
Switch the audio system off for a few minutes to allow the system to cool.
271
272
Visual search
Exterior
Remote control key
- opening/closing
- anti-theft protection
- starting
- battery
Door mirrors
Lighting controls
Headlamp adjustment
Changing bulbs
- front lamps
- foglamps
- direction indicator repeaters
Doors
- opening/closing
- central locking
- emergency control
Alarm
Electric child lock
Electric windows
Fuel tank
Misfuel prevention
Accessories
Hill start assist
Braking assistance
Trajectory control
Tyre pressures
Wiper controls
Changing a wiper blade
Boot
Temporary puncture repair kit
Changing a wheel
- tools
- removing/refitting
Changing bulbs
- rear lamps
- 3 rd brake lamp
- number plate lamps
Rear parking sensors
Reversing camera
Towbar
Towing
Interior
Boot fittings
- rear parcel shelf
- hooks
- stowing rings
Front seats
ISoFIX mountings
Rear seats
Child seats
Seat belts
Visual search
Interior fittings
- auxiliary sockets
- centre armrest
- mat
Glove box deactivating the passenger's airbag
audio pre-equipment
Airbags
.
273
274
Visual search
Instruments and controls
Lighting controls
Headlamp adjustment
Rear view mirror
Zenith windscreen blind
Sun visor
Multifunction screens
Hazard warning lamps
Scented air freshener
Ventilation / Heating
Manual air conditioning
Digital air conditioning
Rear screen demist/defrost
dashboard fuses
Opening the bonnet
Interior mood lighting
Manual gearbox
Electronic gearbox
Automatic gearbox
Gear efficiency indicator
Parking brake
Instrument panels
Warning lamps
Gauges and indicators
Adjustment buttons
- trip distance recorder /clock
- lighting dimmer / black panel
Steering wheel adjustment
Wiper controls
Trip computer
Stop & Start
Door mirrors
Electric windows
Speed limiter
Cruise control
Audio system
Setting the date/time eMyWay
Setting the date/time
Emergency or assistance call
Visual search
Technical data - Maintenance
Petrol engines
LPG engines
Diesel engines
Identification markings
Running out of diesel
Checking levels
- oil
- brake fluid
- coolant
- screenwash fluid
- additive (Diesel with particle emissions filter)
Changing bulbs
- front
- rear
- interior
Bonnet
Under-bonnet layout, petrol
Under-bonnet layout, diesel
Battery
Energy economy mode
Engine compartment fuses
Checking components
- battery
- air filter / passenger compartment filter
- oil filter
- particle filter (diesel)
- brake pads/discs
.
275
276
Alphabetical index
A abS and EbFd systems .............................
accessories ................................................
Accessory socket, 12V
.................................
adjusting headlamps ....................................
adjusting head restraints ..............................49
Adjusting the steering wheel
........................
airbags ........................................................109
airbags, curtain ....................................
airbags, front.......................................
airbags, lateral .....................................
air conditioning ............................................... 8
air conditioning, automatic .....................40, 44
air conditioning, manual ......................... 40, 41
air filter ........................................................
Air flow
............................................................8
air intake .......................................................44
air recirculation .............................................44
air vents ........................................................39
alarm .............................................................
ambient temperature (display)...................... 10
anti-lock braking system (abS) ..................
anti-pinch ......................................................60
anti-theft .......................................................
armrest, front ................................................ 81
assistance call ............................
Audible warning
..........................................100
audio streaming (bluetooth) ...............
audio system ...............................
automatic illumination of headlamps ........................................
automatic operation of hazard warning lamps
............................99
Automatic rain sensitive windscreen wipers
...................................................
auxiliary socket ...................................
auxiliary sockets .........................................
B battery .................................................
battery, charging .........................................
battery, remote control ...........................
black panel....................................................
blind ..............................................................80
bluetooth (hands-free) ........................
bluetooth (telephone) ..................................
bonnet .........................................................
boot ...............................................................
boot lamp ..............................................
brake discs ..................................................143
brake lamps ................................................ 161
braking assistance system .........................
Changing a bulb ..........................
Changing a fuse ..........................................164
Changing a wheel
....................................... 149
Changing a wiper blade
........................
Changing the date .............................
Changing the remote control battery.............................................
Changing the time .......................
Checking levels .................................... 139-141
Checking the engine oil level ........................
Checking tyre pressures
(using the kit) ............................................144
Checks ................................
Child lock .......................................................98
Children ................................................... 93-96
Child seats ...........................
Child seats, conventional ..............................
CITRoËn Localised assistance Call .........196
CITRoËn Localised Emergency Call.........196
Clock .............................................................
Closing the boot ......................................
Closing the doors ....................................
Connectors, audio ........................
Coolant level ............................................... 141
Courtesy mirror ............................................. 81
Cruise control ..............................................
Cup holder .....................................................
C
Capacity, fuel tank ........................................66
Cd MP3 .......................................................
Central locking ........................................
Alphabetical index
D date (setting) .....................................
daytime running lamps .................................
deactivating the passenger airbag .............109
Deactivating the rear windows
deadlocking ..................................................
defrosting ................................................ 41, 46
demisting ................................................ 41, 44
dials and gauges .................................... 10, 11
diesel additive level .................................... 141
Diesel engine pre-heat warning lamp
dimensions ................................................. 193
dipped beam .........................................
dipstick ..................................................
direction indicators ...............................99, 161
doors .............................................................
doors emergency control .............................64
door trays ......................................................
dynamic stability control (dSC) ......16, 18, 106
E
Eba (Emergency braking assistance) ........
Eco-driving ..................................................... 8
Eco-driving (advice) ........................................8
Economical driving ........................................8
Economy mode ...........................................
Electric window controls
...............................60
Electronic brake force distribution
(EbFd) ......................................................
Electronic engine immobiliser.................
Electronic gearbox system .............................8
Emergency boot release ...............................
Emergency braking system ........................
Emergency call ...........................
Emergency warning lamps
eMyWay ................................................
Energy economy mode ...............................
Engine compartment ..........................
Engine compartment fusebox .....................164
Engine, diesel .........................
Engine oil .................................................... 139
Engine oil level indicator .......................
Engine, petrol .................................
Engines .......................................
Environment ..............................................
Equipment settings ...................
Flashing indicators ........................................99
Foglamps, rear ..............................................
Fragrance cartridge ......................................
Front foglamps ......................................
Front seats ....................................................48
Fuel............................................................
Fuel consumption ............................................8
Fuel filler flap ...........................................66, 68
Fuel gauge ....................................................66
Fuel tank..................................................66, 68
Fusebox, dashboard ...................................164
Fuses ...........................................................164
F
Filling with fuel
........................................ 66-68
Fitting a wheel
.............................................
Fittings, boot .................................................84
Fitting speakers...........................................180
G
Gearbox, automatic ................
Gearbox, electronic ............
Gearbox, manual ............
Gear efficiency indicator .............................
Gear lever .......................................................8
Gear lever, automatic gearbox ................... 118
Gear lever,
electronic gearbox system ............... 114, 143
Gear lever, manual gearbox ....................... 113
Glove box ...................................................... 81
G.P.S. ..........................................................
Guidance .............................................
.
277
278
Alphabetical index
H
Hands-free kit .....................................
Hazard warning lamps
..................................99
Head restraints, front ....................................49
Head restraints, rear .....................................
Heating ...................................................... 8, 41
Height and reach adjustment, steering wheel
............................................
Hill start assist .............................................
Hooks ............................................................
Horn.............................................................100
I
Indicators, direction ......................................99
Inflating accessories (using the kit) ............144
Inflating tyres ..................................................8
Inputs for audio system ...............
Installing speakers ......................................180
Instrument panel lighting ..............................
Instrument panels ................................... 10, 11
Instrument panel screen .................
Interior fittings .........................................
Interior lamp ..........................................
Interior mood lighting ....................................
ISoFIX ..........................................................
ISoFIX child seats .................................. 94-96
ISoFIX mountings...................................94, 96
J
Jack
............................................................. 149
JACK socket
................................
Locking from the inside .................................63
LPG .............................................................
K keeping children safe .........
Key in ignition warning
..................................
Key with remote control
L
Labels, identification ...................................194
Lamps, front ................................................
Lamps, rear ................................................. 161
Lamps, warning and indicator
..........
LEd daytime running lamps .............................................
Level, brake fluid ......................................... 140
Levels and checks ...............................
Lighting bulbs
(replacement) ............................
Lighting control stalk .....................................69
Lighting dimmer ............................................
Lighting, guide-me home ........................
Lighting, interior ..............................
Loading ...........................................................8
Load reduction mode ..................................
Locating your vehicle ....................................
M
Main beam ............................................
Maintenance ...................................................8
Markings, identification ...............................194
Mat ................................................................83
Menu, main .................................................
Mini fuel level ................................................66
Mirror, rear view
............................................
Mirrors, door..................................................
Misfuel prevention .........................................68
Motorway function (direction indicators)
Mountings for ISoFIX seats ...................94, 96
MP3 Cd .......................................................
Music media players ...................................
N
navigation ...........................................
number plate lamps .................................... 161
Alphabetical index
O
oil filter ........................................................
oil level..................................................
opening the bonnet ....................................
opening the boot ....................................
opening the doors ..................................
opening the fuel filler flap .............................66
operation indicator lamps ......................
P
Paint colour code ........................................194
Parcel shelf, rear ...........................................
Parking brake ...................................... 113, 143
Parking sensors, rear.................................. 131
Particle emission filter ........................
Passenger compartment filter ....................
Player, Cd MP3 ...........................................
Port, USb ..............................
Preheater, diesel .......................................... 13
Priming the fuel system .............................. 136
Protecting children ........ 86-88, 93-96, 98, 109
Puncture ......................................................144
R
Radio ..........................................
Radio pre-equipment ..................................180
Rear foglamp............................................... 161
Rear screen (demisting) ................................46
Recharging the battery ...............................
Reduction of electrical load ........................
Regeneration of the particle emissions filter
Reinitialising the electric windows
Reinitialising the remote control ...................
Remote control ........................................
Removing a wheel
......................................
Removing the mat .........................................83
Replacing bulbs ..........................
Replacing fuses ..........................................164
Replacing the air filter .................................
Replacing the oil filter .................................
Replacing the passenger compartment filter ....................................
Replacing wiper blades
.........................
Resetting the service indicator .....................
Resetting the trip recorder ............................
Rev counter ............................................. 10, 11
Reversing camera ....................................... 133
Reversing lamp ........................................... 161
Risk areas (update) .....................................
Routine checks ...................................
Running out of fuel (diesel) ........................ 136
S
Safety for children ............................ 93, 96, 98
Scented air freshener ...................................
Screen, colour 16/9 .......................................
Screen, colour and mapping...............
Screen menu map ......................
Screen, monochrome ................
Screen, multifunction
(with audio equipment)
...................
Screenwash
..................................................
Screenwash fluid level
................................ 141
Screen-wash reservoir
............................... 141
Seat adjustment ............................................48
Seat belts ......................................
Seat, rear bench ...........................................
Seats, rear .....................................................
Serial number, vehicle ................................194
Service indicator ...........................................
Service warning light
....................................
Servicing .........................................................8
Setting the clock .........................
Short-cut menus .........................................
Sidelamps .....................................
Side repeater ..............................................
Snow chains
................................................
Spare wheel
................................................ 149
Speakers (fitting) .........................................180
Speed limiter ...............................................
Speedometer .......................................... 10, 11
Starting the vehicle .......................
Steering mounted controls, audio ..............
Stopping the vehicle .....................
Stop Start ..........
29, 46, 66, 123, 135, 142, 171
Storage ....................................................
Storage box ...................................................
Storage drawer
.............................................83
Stowing rings
................................................84
.
279
Alphabetical index
Sun visor ....................................................... 81
Synchronising the remote control .................
Synthesiser, voice .......................................
System, navigation......................................
Trajectory control systems ..........................106
Trip computer .....................................
Trip distance recorder ...................................
Tyre pressures ....................................148, 194
Tyres ................................................................ 8
Tyre under-inflation detection .............................
W
Warning lamps ..............................................
Wash-wipe, rear
............................................
Weights .......................................
Window controls
...........................................60
Wiper control stalk ...................................
Wiper, rear.....................................................
Wipers .....................................................
280
T
Table of weights
..........................
Tables of engines ........................
Tables of fuses ............................................164
Tank, fuel .................................................66, 68
Technical data .............................
Telephone ...........................................
Temperature adjustment ...............................44
Temporary tyre repair kit.............................144
Third brake lamp .........................................
Time .............................................................. 10
TMC (Traffic info) ........................................
Tools ............................................................ 149
Total distance recorder .................................
Towbar
.........................................................
Towed loads
................................
Towing another vehicle
...............................
Traction control (aSR) ....................16, 18, 106
Traffic information (Ta) ...............
Traffic information (TMC) .....................
Trailer ..........................................................
U
Under-inflation (detection) .......................... 101
Unlocking ......................................................
Unlocking from the inside .............................63
Update risk areas ........................................
USb box ........................................................
USb Reader ..........................................
V
Vehicle configuration ................
Ventilation ............................................... 39-41
Z
Zenith windscreen
.........................................80
This handbook describes all of the equipment available in the whole range.
Your vehicle will be fitted with some of this equipment described in this document, depending on its trim level, version and the specification for the country in which it is sold.
The descriptions and illustrations are given without any obligation. automobiles CITRoËn reserves the right to modify the technical specifications, equipment and accessories without having to update this edition of the handbook.
For any work on your vehicle, use a qualified workshop that has the technical information, competence and equipment required, which a
CITRoËn dealer is able to provide.
automobiles CITRoËn declares, by application of the provisions of the European regulation
(Directive 2000/53) relating to End of Life Vehicles, that it achieves the objectives set by this regulation and that recycled materials are used in the manufacture of the products that it sells.
This document is an integral part of your vehicle. It should be passed on to the new user in the event of sale or transfer.
In addition, there are labels present in your vehicle to warn you of the need for certain precautions to take for your safety; don't remove them, they will be useful again for a new owner.
Reproduction or translation of all or part of this document is prohibited without written authorisation from automobiles CITRoËn.
Printed in the EU anglais
04-14
14.C3.0030
anglais
2014 – DOCUMENTATION DE BORD
4Dconcept
Diadeis
Entagos
CRÉATIVE TECHNOLOGIE
Monitoring
Instrument panels with manual gearbox
Panel grouping together the vehicle operation indication dials and warning lamps.
Dials Screen
1.
Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2.
Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
3.
Fuel level.
Indicates the quantity of fuel remaining in the tank.
4.
Screen.
5.
Display management button
Servicing information.
Adjust the time and choose units.
Reset the service indicator.
6.
Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For more information, refer to the section on the button or function and its associated display.
A.
Ambient temperature.
(°Celsius or °Fahrenheit)
B.
Gear shift indicator.
C.
Time.
D.
Engine oil level indicator.
Appears a few seconds after switching on the ignition, then disappears.
E.
Trip computer.
F.
Service indicator or Range related to the AdBlue additive and the SCR system (miles or km), then, total mileage.
These functions are displayed successively when switching on the ignition.
2
C3-add_en_Chap01_Controle-de-marche_ed01-2014
Warning/indicator lamp is on
AdBlue additive
(BlueHDi Diesel)
fixed, on switching on the ignition, accompanied by an audible signal and a message indicating the remaining driving range.
Cause
The remaining driving range is between 350 miles (600 km) and
1500 miles (2400 km).
+ flashing associated with the SERVICE warning lamp, accompanied by an audible signal and a message indicating the remaining driving range.
The remaining driving range is between 0 and 375 miles (600 km).
Monitoring 1
Action / Observations
Have the AdBlue ® additive tank topped up as soon as possible: go to a CITROËN dealer or a qualified workshop, or carry out this operation yourself by referring to the corresponding section.
You must top-up the AdBlue ® additive tank to avoid a breakdown : go to a CITROËN delaer or a qualified workshop, or carry out this operation yourself by referring to the corresponding section.
flashing, associated with the SERVICE warning lamp, accompanied by an audible signal and a message indicating that starting is prevented.
The AdBlue ® tank is empty: the starting inhibition system required by legislation prevents starting of the engine.
To be able to start the engine, you must top-up the
AdBlue ® additive tank: go to a CITROËN dealer or a qualified workshop, or carry out this operation yourself by referring to the corresponding section.
It is essential to add at least 3.8 litres of AdBlue the additive tank.
3
C3-add_en_Chap01_Controle-de-marche_ed01-2014
Monitoring
Warning/indicator lamp is on
+
SCR emissions control system
(BlueHDi Diesel)
fixed, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message.
Cause
A fault with the SCR emissions control system has been detected.
+
flashing, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message indicating the remaining driving range.
Action / Observations
This alert disappears once the exhaust emissions return to normal levels.
After confirmation of the fault with the emissions control system, you can drive for up to 650 miles (1 100 km) before the engine starting inhibition system is triggered.
Contact a CITROËN dealer or a qualified workshop without delay breakdown .
,
flashing, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message.
You have exceeded the authorised driving limit following confirmation of a fault with the emissions control system: the engine starting inhibition system prevents starting of the engine.
To be able to start the engine, you must call on a CITROËN dealer or a qualified workshop.
4
C3-add_en_Chap01_Controle-de-marche_ed01-2014
Service indicator
System which informs the driver when the next service is due, in accordance with the manufacturer's servicing schedule.
The point at which the next service is due is calculated from the last indicator zero reset, depending on the distance travelled and the time elapsed since the last service.
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no service information appears in the screen.
Between 600 miles (1 000 km) and 1 800 miles
(3 000 km) remain before the next service is due
For 5 seconds after the ignition is switched on, the spanner symbolising the service operations comes on. The distance recorder display line indicates the distance remaining before the next service is due.
Example: 1 700 miles (2 800 km) remain before the next service is due.
For 5 seconds after the ignition is switched on, the screen indicates:
For BlueHDi Diesel versions, the degree of deterioration of the engine oil is also taken into account (depending on the country of sale).
5 seconds after the ignition is switched on, the spanner goes off ; the distance recorder resumes its normal operation. The screen then indicates the total distance.
Monitoring 1
Less than 600 miles (1 000 km) remain before the next service is due
Example: 560 miles (900 km) remain before the next service is due.
For 5 seconds after the ignition is switched on, the screen indicates:
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a service must be carried out soon.
5
C3-add_en_Chap01_Controle-de-marche_ed01-2014
Monitoring
Service overdue
For 5 seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible.
Example: the service is overdue by 180 miles
(300 km).
For 5 seconds after the ignition is switched on, the screen indicates:
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the driving conditions.
Therefore, the spanner may also come on if you have exceeded the period since the last service, indicated in the manufacturer's service schedule.
For BlueHDi Diesel versions, the spanner may also be brought on earlier than expected, depending on the degree of deterioration of the engine oil
(depending on the country of sale).
The rate of deterioration of the engine oil depends on the driving conditions in which the vehicle is used.
For BlueHDi Diesel versions, this alert may also be accompanied by the fixed illumination of the service warning lamp when the ignition is on.
C3-add_en_Chap01_Controle-de-marche_ed01-2014
6
Running out of fuel (Diesel)
If your vehicle is fitted with an HDI engine, the fuel system must be primed if you run out of fuel.
This system consists of a priming pump and a transparent pipe under the bonnet.
BlueHDi 100 engines
Fill the fuel tank with at least five litres of Diesel.
Switch on the ignition (without starting the engine).
Wait around 6 seconds and switch off the ignition.
Repeat the operation 10 times.
Operate the starter to run the engine.
Fill the fuel tank with at least five litres of Diesel.
Open the bonnet.
Depending on version, unclip the cover to gain access to the priming pump.
Squeeze and release the priming pump until resistance is felt (could be from the first application) and fuel appears in the transparent pipe with the green connector.
Operate the starter until the engine starts.
Depending on version, put the cover back in position and clip it in place.
Close the bonnet.
If the engine does not start at the first attempt, do not try again.
Operate the priming pump again, then the starter.
7
C3-add_en_Chap10_Verifications_ed01-2014
Checks
10
Practical information
AdBlue
®
additive and SCR system for BlueHDi Diesel engines
To assure respect for the environment and conformity with the new Euro 6 emissions standard, without adversely affecting the performance or fuel consumption of Diesel engines, CITROËN has taken the decision to equip its vehicles with an effective system that associates SCR (Selective Catalytic Reduction) with a particle filter (FAP) for the treatment of exhaust gases.
The AdBlue ® additive is held in a special tank located under the boot at the rear of the vehicle. It has a capacity of 17 litres: this provides a driving range of about 12 500 miles
(20 000 km), after which an alert is triggered warning you when the reserve remaining is enough for just 1 500 miles (2 400 km).
During each scheduled service of your vehicle by a CITROËN dealer or a qualified workshop, the AdBlue additive tank is refilled in order to allow normal operation of the SCR system.
Presentation of the SCR system
Using an additive called AdBlue ® containing urea, a catalytic converter turns up to 85% of nitrous oxides (NOx) into nitrogen and water, which are harmless to health and the environment.
If the estimated mileage between two services is greater than 12 500 miles (20 000 km), we recommend that you go to a CITROËN dealer or a qualified workshop to have the necessary top-up carried out.
Once the AdBlue ® tank is empty, a system required by regulations prevents starting of the engine.
If the SCR is faulty, the level of emissions from your vehicle will no longer meet the Euro 6 standard: you vehicle becomes polluting.
In the event of a confirmed fault with the SCR system, you must go to a CITROËN dealer or a qualified workshop as soon as possible: after a running distance of 650 miles
(1 100 km), a system will be triggered automatically to prevent engine starting.
8
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
Range indicators
When switching on the ignition, an indicator gives an estimate of the distance that can be travelled with your vehicle before engine starting is automatically prevented, once the vehicle starts using the reserve of AdBlue ® or after a fault is detected with the SCR system.
In the event of simultaneous system fault and low AdBlue ® level, the shortest range is the one displayed.
In the event of the risk of nonstarting related to a lack of
AdBlue
The engine start prevention system required by regulations is activated automatically once the AdBlue ® tank is empty.
Range greater than 1 500 miles (2 400 km)
When the ignition is switched on, no information on range is displayed automatically in the instrument panel.
Depending on your vehicle's equipment, the range indicator will appear either:
- in the instrument panel screen (versions without audio system), or
- in the multifunction screen.
11
9
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
For vehicles without a multifunction screen, the range indicator appears in the instrument panel screen.
Remaining range between 350 and 1500 miles (600 and 2 400 km) Remaining range between 0 and 350 miles (0 and 600 km) Breakdown related to a lack of AdBlue ® additive
When switching on the ignition, the UREA warning lamp comes on, accompanied by an audible signal and the temporary display in the instrument panel of "NO START IN" and a distance, indicating the remaining range expressed in miles or kilometres before engine starting is prevented - (For example "NO START
IN 900 miles" means that "Starting will be prevented in 900 miles".
When driving, this display appears every
150 miles (300 km) until the additive tank has been topped-up.
Go to a CITROËN dealer or a qualified workshop to have the AdBlue ® tank topped-up.
You can also top-up the tank yourself.
Refer to the "Topping-up" section.
When switching on the ignition, the SERVICE warning lamp comes on and the UREA warning lamp flashes, accompanied by an audible signal and the temporary display in the instrument panel of "NO START IN" and a distance indicating the remaining range expressed in miles or kilometres before engine starting is prevented - (For example "NO START IN
350 miles" means "Starting will be prevented in
350 miles".
When driving, this display appears every
30 seconds until the additive tank has been topped-up.
Go to a CITROËN dealer or a qualified workshop to have the AdBlue ® tank topped-up.
You can also top-up the tank yourself.
Refer to the "Topping-up" section.
Otherwise you will not be able to restart your engine.
When switching on the ignition, the SERVICE warning lamp comes on and the UREA warning lamp flashes, accompanied by an audible signal and the temporary display in the instrument panel of "NO START IN" and 0 km or miles -
("NO START IN 0 miles" means "Starting prevented").
The AdBlue ® tank is empty: the system required by regulations prevents engine starting.
To be able to start the engine, we recommend that you call on a CITROËN dealer or a qualified workshop for the top-up required. If you carry out the top-up yourself, it is essential to add at least 3.8 litres of
AdBlue ® to the additive tank.
Refer to the "Topping-up" section.
10
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
For vehicles fi tted a multifunction screen, the range indicator appears in the screen.
Remaining range between 350 and 1500 miles (600 and 2 400 km) Remaining range between 0 and 350 miles (0 and 600 km) Breakdown related to a lack of AdBlue ® additive
When switching on the ignition, the
UREA warning lamp comes on, accompanied by an audible signal and the display of a message (e.g.: "Top up emissions additive:
Starting prevented in 900 miles") indicating the remaining range expressed in miles or kilometres.
When driving, the message is displayed every
150 miles (300 km) until the additive tank has been topped-up.
Go to a CITROËN dealer or a qualified workshop to have the AdBlue ® tank topped-up.
You can also top-up the tank yourself.
Refer to the "Topping-up" section.
When switching on the ignition, the SERVICE warning lamp comes on and the UREA warning lamp flashes, accompanied by an audible signal and the display of a message (e.g.
"Top up emissions additive: Starting prevented in 350 miles") indicating the remaining range expressed in miles or kilometres.
When driving, the message is displayed every
30 seconds until the additive tank has been topped-up.
Go to a CITROËN dealer or a qualified workshop to have the AdBlue ® tank topped-up. tank topped-up.
You can also top-up the tank yourself.
Refer to the "Topping-up" section.
Otherwise you will not be able to restart your engine.
When switching on the ignition, the SERVICE warning lamp comes on and the UREA warning lamp flashes, accompanied by an audible signal and the display of the message "Top up emissions additive: Starting prevented".
The AdBlue ® tank is empty: the system required by regulations prevents engine starting.
To be able to start the engine, we recommend that you call on a CITROËN dealer or a qualified workshop for the top-up required. If you carry out the top-up yourself, it is essential to add at least 3.8 litres of
AdBlue ® to the tank.
Refer to the "Topping-up" section.
11
11
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
In the event of a fault with the the SCR emissions control system
A system that prevents engine starting is activated automatically from
650 miles (1 100 km) after confirmation of a fault with the SCR emissions control system. Have the system checked by a CITROËN dealer or a qualified workshop as soon as possible.
For vehicles without a multifunction screen, the range indicator appears in the instrument panel screen.
In the event of the detection of a fault
During an authorised driving phase
(between 650 miles and 0 miles) (1 100 km and 0 km)
The UREA, SERVICE and diagnostic warning lamps comes on, accompanied by an audible signal.
The alert is triggered when driving, when the fault is detected for the first time, then when switching on the ignition for subsequent journeys, while the fault persists.
If it is a temporary fault, the alert disappears during the next journey, after a self diagnosis test of the SCR emissions control system.
If a fault with the SCR system is confirmed (after
30 miles (50 km) covered with the permanent display of the message signalling a fault), the
SERVICE and engine diagnostic warning lamps come on and the UREA warning lamp flashes, accompanied by an audible signal and the temporary display in the instrument panel of
"NO START IN" and a distance, indicating the remaining range express in miles or kilometres before engine starting is prevented -
(e.g.: "NO START IN 350 miles" means "Starting will be prevented in 350 miles".
While driving, this display appears every
30 seconds while the fault with the SCR system persists.
The alert is repeated when switching on the ignition.
You should go to a CITROËN dealer or a qualified workshop as soon as possible.
Otherwise, you will not be able to restart your engine.
12
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
Starting prevented
Every time the ignition is switched on, the
SERVICE and engine diagnostic warning lamps come on and the UREA warning lamp flashes, accompanied by the temporary display of "NO START IN" and 0 miles or kilometres -
("NO START IN 0 miles" means "Starting prevented").
You have exceeded the authorised driving limit: the starting prevention system inhibits engine starting.
To be able to start the engine, you must call on a CITROËN dealer or a qualified workshop.
13
C3-add_en_Chap11_Info-pratiques_ed01-2014
11
Practical information
For vehicles fi tted a multifunction screen, the range indicator appears in the screen.
In the event of the detection of a fault
During an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
Starting prevented
The UREA, SERVICE and diagnostic warning lamps comes on, accompanied by an audible signal and the display of a message
"Emissions fault".
The alert is triggered when driving when the fault is detected for the first time, then when switching on the ignition for subsequent journeys, while the fault persists.
If it is a temporary fault, the alert disappears during the next journey, after self-diagnosis of the SCR system.
If a fault with the SCR system is confirmed (after
30 miles (50 km) covered with the permanent display of the message signalling a fault), the SERVICE and engine diagnostic warning lamps come on and the
UREA warning lamp flashes, accompanied by an audible signal and the display of a message
(e.g.: "Emissions fault: Starting prevented in 150 miles") indicating the remaining range express in miles or kilometres.
While driving, the message is displayed every
30 seconds while the fault with the SCR system persists.
The alert is repeated when switching on the ignition.
You should go to a CITROËN dealer or a qualified workshop as soon as possible.
Otherwise, you will not be able to restart your engine.
14
Every time the ignition is switched on, the SERVICE and engine diagnostic warning lamps come on and the UREA warning lamp flashes, accompanied by an audible signal and the display of the message
"Emissions fault: Starting prevented".
You have exceeded the authorised driving limit: the starting prevention system inhibits engine starting.
To be able to start the engine, you must call on a CITROËN dealer or a qualified workshop.
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
Freezing of the AdBlue ® additive
The AdBlue ® additive freezes at temperatures below around -11°C.
The SCR system includes a heater for the AdBlue ® tank, allowing you to continue driving in very cold conditions.
15
C3-add_en_Chap11_Info-pratiques_ed01-2014
11
Practical information
Filling the AdBlue ® tank is an operation included in every routine service on your vehicle by a CITROËN dealer or a qualified workshop.
Nevertheless, given the capacity of the tank, it may be necessary to top-up the additive between services, more particularly if an alert
(warning lamps and a message) signals the requirement.
You can got to a CITROËN dealer or a qualified workshop.
If you envisage topping-up yourself, please read the following warnings carefully.
Precautions in use
The AdBlue ® additive is an urea-based solution. This liquid is non-flammable, colourless and odourless (kept in a cool area).
In the event of contact with the skin, wash the affected area with soap and water. In the event of contact with the eyes, wash (irrigate) the eyes with large amounts of water or with an eye wash solution for at least 15 minutes.
If a burning sensation or irritation persists, get medical attention.
If swallowed, immediately wash out the mouth with clean water and then drink plenty of water.
In certain conditions (high ambient temperature, for example), the risk of release of ammonia cannot be excluded: do not inhale the product. Ammonia vapour has en irritant effect on mucous membranes (eyes, nose and throat).
Use only AdBlue ® additive that meets the
ISO 22241 standard.
Never dilute the additive with water.
Never pour the additive into the Diesel fuel tank.
The supply in a non-drip bottle simplifies toping-up. You can obtain 1.89 litre (half a US gallon) bottles from a CITROËN dealer or a qualified workshop.
Keep AdBlue ® out of the reach of children, in its original bottle.
Never transfer AdBlue ® to another container: it would loose its purity.
Never top-up from an AdBlue ® dispenser reserved for heavy goods vehicles.
16
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
Recommendations on storage
AdBlue ® freezes at about -11°C and deteriorates above 25°C. It is recommended that bottles be stored in a cool area and protected from direct sunlight.
Under these conditions, the additive can be kept for at least a year.
If the additive has frozen, can be used once it has completely thawed out.
Procedure
Before topping-up, ensure that the vehicle is parked on a flat and level surface.
In wintry conditions, ensure that the temperature of the vehicle is above -11°C.
Otherwise, by freezing, the AdBlue ® cannot be poured into its tank. Park your vehicle in a warmer area for a few hours to allow the top-up to be carried out.
Never store bottles of AdBlue ® in your vehicle.
For access to the AdBlue ® tank, raise the boot carpet then, depending on equipment, lift out the spare wheel and/or the storage box.
Without pressing, turn the black cap a quarter turn anti-clockwise and lift it off. 11
Turn the blue cap a 6 th of a turn anticlockwise.
Lift off the cap.
17
C3-add_en_Chap11_Info-pratiques_ed01-2014
Practical information
Obtain a bottle of AdBlue ® . After first checking the use-by date, read carefully the instructions on use on the label before pouring the contents of the bottle into your vehicle's AdBlue ® tank.
Important :
AdBlue ®
if your vehicle's
tank is completely empty - which is confirmed by the alert messages and the impossibility of starting the engine, you must add at least 3.8 litres (so two 1.89 litre bottles).
After emptying the bottle, wipe away any spillage around the tank filler using a damp cloth.
If any additive is split or splashed, wash immediately with cold water or wipe with a damp cloth.
If the additive has crystallised, clean it off using a sponge and hot water.
Refit the blue cap to the tank and turn it a 6 th of a turn clockwise, to its stop.
Refit the black cap and turn it a quarter of a turn clockwise without pressing. Ensure that the indicator on the cap lines up with the indicator on the support.
Depending on equipment, return the spare wheel and/or the storage box to the bottom of the boot.
Refit the boot carpet and close the tailgate.
Important: in the event of a top-up after a breakdown because of a lack of additive , you must wait around 5 minutes before switching on the ignition, without opening the driver's door, locking the vehicle or introducing the key into the ignition switch .
Switch on the ignition, then, after
10 seconds, start the engine.
Never dispose of AdBlue ® additive bottles in the household waste. Place them in a special container provided this purpose or take them to your dealer.
18
C3-add_en_Chap11_Info-pratiques_ed01-2014
Technical data
Petrol engines and gearboxes
These engines are added to those already present in your Handbook.
Model code:
SC...
Engine
HNZ 6 / S
PureTech 110 S&S
Gearbox
Cubic capacity (cc)
Bore x stroke (mm)
Max power: EU standard (kW) *
Max power engine speed (rpm)
Max torque: EU standard (Nm)
Max torque engine speed (rpm)
Fuel
Manual
(5-speed)
1 199
75 x 90.5
81
5 500
205
1 500
Unleaded
HMZ 6
PureTech 82
Manual
(5-speed)
1 199
75 x 90.5
60
5 760
118
2 750
Unleaded
HMZ 6/PS
Puretech 82 S&S
ETG
(5-speed electronic)
1 199
75 x 90.5
60
5 760
118
2 750
Unleaded
ZMZ 6
PureTech 68
Manual
(5-speed)
999
71 x 84.1
60
6 000
95
3 000
Unleaded
Yes Yes Yes Yes Catalytic converter
OIL CAPACITIES (in litres)
Engine (with filter replacement) 3.5 3.25 3.25 3.25
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
12
19
C3-add_en_Chap12_Caracteristiques_ed01-2014
Technical data
Petrol weights and towed loads (in kg)
Engine PureTech 110 S&S PureTech 82
Gearbox
Model code:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % gradient
- Braked trailer (within GTW limit) on a 12 % gradient
- Braked trailer * (with load transfer within the
GTW limit)
- Unbraked trailer
- Recommended nose weight
Manual
(5-speed)
HNZ 6 / S
1 070
1 145
1 598
2 498
900
Manual
(5-speed)
HMZ 6
975
1 050
1 525
2 325
800
PureTech 82 S&S
ETG
(5-speed electronic)
HMZ 6 / PS
980
1 055
1 541
2 041
500
PureTech 68
Manual
(5-speed)
ZMZ 6
973
1 048
1 520
1 970
450
1 150
570
46
1 100
520
46
800
500
46
775
450
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
20
C3-add_en_Chap12_Caracteristiques_ed01-2014
Technical data
Diesel engines and gearboxes
These engines are added to those already present in your Handbook.
Model code:
SC...
Engine
Gearbox
Cubic capacity (cc)
BHY 6 / S
BlueHDi 100
Manual
(5-speed)
1 560
Bore x stroke (mm) 75 x 88.3
Max. power: EU standard (kW) *
Max. power engine speed (rpm)
Max. torque: EU standard (Nm)
Max. torque engine speed (rpm)
Fuel
Catalytic converter
73
3 750
254
1 750
Diesel
Yes
BHW 6
BlueHDi 75
Manual
(5-speed)
1 560
75 x 88.3
55
3 500
233
1 750
Diesel
Yes
Yes Yes Particle filter (FAP)
OIL CAPACITIES (in litres)
Engine (with filter replacement) 3.75 3.75
* The maximum power corresponds to the value type approved on a test bed, under conditions defined by European legislation (Directive 1999/99/EC).
12
.../S : model fitted with Stop & Start.
21
C3-add_en_Chap12_Caracteristiques_ed01-2014
Technical data
Diesel weights and towed loads (in kg)
Engine
Gearbox
BlueHDi 100
Manual
(5-speed)
Model code:
SC...
- Unladen weight
- Kerb weight
- Gross vehicle weight (GVW)
- Gross train weight (GTW) on a 12 % gradient
- Braked trailer (within GTW limit) on 12 % gradient
- Braked trailer * (with load transfer with the
GTW limit)
- Unbraked trailer
- Recommended nose weight
BHY 6 / S
1 085
1 160
1 652
2 552
900
1 150
570
46
BlueHDi 75
Manual
(5-speed)
BHW 6
1 080
1 155
1 645
2 545
900
1 150
570
46
* The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount. Warning: towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C, limit the towed load.
22
C3-add_en_Chap12_Caracteristiques_ed01-2014
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
