USER MANUAL

 TE STEER
High Resolution IR Camera
The product image may differ from the actual product.
Please read the instructions thoroughly before using the product.
FEATURES
USER MANUAL
2362
. Excellent image quality
=] CO LT Y Pd =
PACKAGE CONTENT
. IR LED effective range reaches up to 15 meters
. IP66 standard approved outdoor housing
. Cable management to hide the cable in the bracket for cable damage prevention
. High resolution for clearer and sharper images
. High sensitivity in the dark environment, 0.6Lux / F2.0, OLux (IR ON)
. Day and night features for 24-hour surveillance
> — IR camera with a power and video cable * 1
> Bracket * 1
ооо
La
> Accessorypack x1
= User Manual * 1
4
SPECIFICATIONS*
Pick up Element 1/3" HR Color CCD image sensor
Number of Pixel 771(H) x 492(V) <NTSC= / 753(H) x 582(V) <PAL>
Resolution 500 TV Lines |
Minimum illumination 0.6Lux / F2.0, OLux (IR ON)
IR LED 21 units
IR Effective Range Up to 15 Meters
S/N Ratio More than 48dB (AGC off)
Electronic Shutter 1/60 (1/50) to 1/100,000 sec.
Lens f3.6mm / F2.0
Lens Angle 92.6"
IRIS Mode AES
White Balance ATW
IP Rating IP66
Video Output 1.0Vp-p composite, 750
Power Source (+10%) DC12V
Current Consumption (+10%) 90mA (IR OFF), 210mA (IR ON)
Dimensions (mm)** 116.13(L) x 60(W) x 79.58(H)
* The specifications are subject to change without notice.
** Dimensional Tolerance; + 5mm
K136C V1.2
INSTALLATIONS
1. Find the supplied intemal part of the bracket (as shown in Figure 1) in the accessory pack.
2. Pass the video cable first, and then pass the power cable through the middle hole of the intemal part of the bracket (as shown
in Figure 1).
3. Use the supplied three screws to attach the intemal part of the bracket to the wall or ceiling (as shown in Figure 2). Then apply
one of the two following methods:
3.1 Drill a hole in advance on the proper position of the wall or ceiling for the power and video cable to pass through later.
3.2 Pull the cables through one of the gaps of the intemal part of the bracket.
4. When 3.1 is applied, after the video and power cables are passed through the intemal part of the bracket, pull the cables till the
internal part of the bracket is joined to the main body of the bracket.
When 3.2 is applied, cut the thinner part of the bracket's main body (as pointed by the red amow in Figure 3) to allow the video
and power cables to pass through later.
5. Adjust the viewing angle of the camera (as shown in Figure 4), then use the supplied wrench to fasten the joint lock by
clockwise and rotate the attached screw to the end.
Video Cable
Power Cable
Figure 1 Figure 2 Figure 3 Figure 4
CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a 12V DC regulated power supply.
Note: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The power tolerance of
this unit is DC12Y + 10%. Over maximum DC 12V power input will damage this unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output and the monitor video input with 750) coaxial cable.
RISK OF ELECTRIC SHOCK
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of such
damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, Is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
>>
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the Restriction of
Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly “lead-free”
and without the hazardous substances cited in the directive.
A
O
L
un
3
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected seperately
at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of
these products as unsorted municipal waste.
| 3
CE Mark
This apparatus is manufactured to comply with the radio interference.
A
mM
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or
remove any content in this manual at any time,