advertisement
HIGH SENSITIVITY COLOR CAMERA
INSTRUCTION MANUAL
SHC-730N/P
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703
TEL : 82-31-740-8137~41 FAX: 82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)
Samsung House, 1000 Hillswood Drive Hillswood Business
Park Chertsey Surrey KT16 OPS
TEL : 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
•
SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)
Closed Circuit Division 40 Seaview Drive, Secaucus N.J 07094,
U.S.A
TEL : (201) 902-0347 FAX: (201) 902-0429
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL : 86-22-2761-9698 FAX: 86-22-2761-6514
P/No. : Z6806-0541-01A
VAN 04. 12
SAMSUNG CCD CAMERA
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
Features
Fine Picture in Ultra Low illumination.
SV-III built-in DSP and 1/3 high density
CCD allows bright and high quality images to be captured in ultra low light condition.
- 0.13Lux at Color
- 0.001Lux at Sens-Up mode
Day & Night
The camera provides automatic mode change over by sensing day or night conditions. It can change color mode in the day condition for optimal color and
BW mode in night condition for clear identification.
Wide Dynamic Range(WDR)
SV-III DSP has Strong compensation performance in WDR.
So It always shows obvious, clear and perfect light contrast picture in any environment.
Motion Detection
The camera transmits an alert signal to the MD Output Terminal when it detects motion of an object. If you connect an optional alarm to the camera, you can get the effective surveillance.
SSNR(Samsung Super Noise
Reduction)
SHC-730 has powerful DSP that can remove image noise efficiently and it shows clean and obvious image in low luminance.
VIDEO/DC Lens Selectable
The camera accepts 2 types of auto iris lenses (DC type/VIDEO type) and is set with the VIDEO/DC selection switch.
High Resolution
The horizontal resolution of 520TV lines at Color mode and 570TV lines at BW mode can be achieved by using a high density CCD having Double Speed
410,000 pixels SONY CCD, which provides clean, noiseless and reliable pictures.
Miscellaneous Function
Privacy, Flip(H/V-REV), D-ZOOM, Burst
ON/OFF, SYNC(INT/LL), COLOR, TONE,
SHARPNESS.
Controlled by OSD menu and
RS-232C
You can control the camera using OSD menu and RS-232C jack at a remote place.
COLOR CCD CAMERA
4
User’s Manual
Warning
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
COLOR CCD CAMERA
5
User’s Manual
Contents
Precautions
Composition
Name and Function of Each Part
Front
Side
Bottom
Back
Connection
Lens
• Installing Auto Iris Lens
• Installing C/CS-Mount Lens
Connecting to Monitor
Connecting to Power
11
11
12
13
14
15
15
8
10
19
20
Operating Your Camera
Configuration of The Menu
Setting Up The Menu
• CAMERA ID
• BACKLIGHT
• WHITE BALANCE
• MOTION DETECTION
• LENS SELECTION
• SHUTTER SPEED CONTROL
• AGC
• SENSE UP
• SSNR
• SPECIAL
Using Reomte Jack / MD Output / D&N Input
Troubleshooting
Specifications
40
42
44
21
21
22
23
32
34
35
36
37
26
27
28
30
COLOR CCD CAMERA
6
User’s Manual COLOR CCD CAMERA
7
User’s Manual
Precautions
Do not install the camera in extreme temperature conditions.
Do not install or use the camera in an environment where the humidity is high.
Do not drop the camera or subject them to physical shocks.
Never keep the camera face to strong light directly.
Only use the camera under conditions where temperatures are between -10˚C and +50˚C. Be especially careful to provide ventilation when operating under high temperatures.
It can cause the image quality to be poor.
Do not install the camera under unstable lighting conditions.
Do not touch the front lens of the camera.
It can cause malfunctions to occur.
Do not expose the camera to rain or spill beverage on it.
It can damage the CCD.
Do not expose the camera to radioactivity.
Severe lighting change or flicker can cause the camera to work improperly.
It is one of the most important parts of the camera. Be careful not to be stained by fingerprint.
COLOR CCD CAMERA
8
User’s Manual
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode the electronic components.
If it is exposed to radioactivity,
For heated CCD, it will be out of order.
Notes
• If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.
• Please check that the power satisfies the normal specification before connecting the camera.
COLOR CCD CAMERA
9
User’s Manual
Composition
1. High Sensitivity Color Camera
2. Auto Iris Lens Plug
3. Remote Plug
4. C-Mount Adapter
5. Instruction Manual
COLOR CCD CAMERA
10
User’s Manual
Name and Function of Each Section
Front
C-Mount Lens Adapter
Used to attach C-mount lens.
Tripod Mounting Bracket
Screw Hole
Used to fix the Tripod mounting bracket on the top of the camera.
Back Focus Adjustment Lever
Used to adjust back focal length
COLOR CCD CAMERA
11
User’s Manual
Name and Function of Each Section
Side
BACK FOCUS ADJUSTMENT LEVER
When you don’t obtain focused point after adjusting lens focus, adjust the lever.
Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
DC/VIDEO Selection Switch
Used to choose DC or VIDEO according to the type of your Auto Iris Lens.
Menu Setup Buttons Cover
Bottom
Tripod Mounting Hole
Used to install the camera on an optional tripod. The tripod must be equipped with the screw specified as shown below.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)
Tripod Mounting Bracket
L
Menu Setup Buttons
• SET Button: Used to access menu mode. Also used to confirm the setting.
• UP/DOWN Button: Used to choose the desired menu item. It also moves the cursor up or down in the menu screen.
• LEFT/RIGHT Button: Used to change the parameter of the selected menu item.
It also moves the cursor the left or right in the menu screen.
COLOR CCD CAMERA
12
User’s Manual
You can remove and install this bracket on the top of the camera. You must use the supplied screw or the equivalent (within 4mm). If not, the bracket may not be fixed properly.
COLOR CCD CAMERA
13
User’s Manual
Name and Function of Each Section
Back
Video Output Jack
Used to connect an external video monitor in jack.
Power LED
The LED turns on when power is supplied.
Remote Jack
Used to connect a remoteplug.
D&N
Used to input Day & Night
Control Signal
MD Output Terminal
Used to output motion detection signal.
Frame Ground
AC / DC Power Terminal
Used to connect an AC 24V or DC 12V power source.
COLOR CCD CAMERA
14
User’s Manual
Connection
LENS
The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and
CS-mount lens.
Notes
If the lens is marked with fingerprints or other marks, the image quality might be poor.
It is recommended to use a high quality lens to improve the image quality under low illumination.
For using main functions it is recommended to use Auto Iris Lens with DC type.
Installing Auto Iris Lens
1. Peel approximately 8mm from the end of the lens cable outer cover.
approx. 8mm
2. Peel approximately 2mm from the end of the cable inner cover.
approx. 2mm
COLOR CCD CAMERA
15
User’s Manual
Connection
3. Remove the cover from the iris lens plug supplied, and solder the lens cable to the plug as shown below.
• Video type :
No. 1 Pin --- Red (Power source)
No. 2 Pin --- N.C
No. 3 Pin --- White (Video signal)
No. 4 Pin --- Black (GND)
• DC type :
No. 1 Pin --- Damping -
No. 2 Pin --- Damping +
No. 3 Pin --- Drive +
No. 4 Pin --- Drive -
Lens cable
No. 3 Pin
No. 1 Pin connector
No. 4 Pin
No. 2 Pin
4. Remove the protective cap, and attach the lens to the camera by turning clockwise.
5. Connect the lens plug to the auto iris connector on the right side of the camera.
Installing C/CS-Mount lens
Before mounting a lens, please check whether it is a C-mount or CS-mount lens.
The back focus is set for the CS-mount lens at the factory.
• Mounting a CS-Mount lens
After removing the protecting cap, attach the lens into the camera by turning clockwise.
6. Set the DC/VIDEO selection switch to DC or VIDEO according to the type of the lens.
COLOR CCD CAMERA
16
User’s Manual
Notes
Use the lens under the specification as shown. Otherwise the lens can damage the camera or abnormal fixing may result.
C-mount lens : 10 mm or less
CS-mount lens : 5 mm or less
A heavy lens may disturb the balance with the camera and possibly result in damage. Don't use a lens heavier than 450g.
It is recommended to set the lens ALC mode to Av mode (Average). Pk mode can be occurred hunting.
COLOR CCD CAMERA
17
User’s Manual
Connection
• Mounting a C-Mount lens
1. Attach the C-Mount lens adapter by turning clockwise.
2. Attach the lens to the camera by turning clockwise.
COLOR CCD CAMERA
18
User’s Manual
Connecting to Monitor
Connect the VIDEO Out jack to the monitor VIDEO In jack.
CCD Camera Monitor
• As the connecting method varies with the instruments, refer to the manual supplied with the instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera. For details, see page 40.
• Only connect the cable when the power is turned off.
• Set the 75Ω/Hi-Z selection switch as shown below if you have an intermediate device.
Intermediate End monitor
CCD Camera
COLOR CCD CAMERA
19
User’s Manual
Connection
Connecting to Power
Each model has different power specification. Please check the name of the model and power specification before connecting to power source.
For AC / DC Power Type
• The wire is polarized. Be sure to connect the wire that white line is on covering to ‘-’ terminal and connect the other one to ‘+’ terminal.
• Use AC 24V/500mA or DC 12V/500mA power source for SHC-730N/P
Resistance of copper wire [at 20C˚ (68˚F)]
Copper wire size (AWG) #24(0.22mm
2
) #22(0.33mm
2
)
Resistance (Ω / m)
Voltage Drop (V/m)
0.078
0.028
0.050
0.018
#20(0.52mm
2
) #18(0.83mm
2
)
0.030
0.011
0.018
0.006
• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
COLOR CCD CAMERA
20
User’s Manual
Operating Your Camera
Configuration of The Menu
SETUP MENU CAMERA ID
• OFF • ON
BACKLIGHT
• WDR • OFF
WHITE BAL.
• ATW • AWC • MANUAL
MOTION DET.
• OFF • ON
LENS
• DC / Video • Manual
SHUTTER
• ESC • A.FLK • MANUAL
AGC
• OFF • LOW • MIDDLE • HIGH
SENSE UP
• OFF • AUTO
SSNR
• OFF • LOW • MIDDLE • HIGH
SPECIAL
• D-ZOOM • PRIVACY • DAY/NIGHT • SYNC
• IMAGE ADJ • PRESET • RETURN • EXIT
EXIT
COLOR CCD CAMERA
21
User’s Manual
Operating Your Camera
Setting Up The Menu
Use the five Setup Menu buttons on side of the camera.
UP button
LEFT button
SET button
DOWN button
RIGHT button
1. Press the SET button to access the setup mode.
• Setup menu is displayed on the monitor screen.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
SPECIAL
EXIT
AUTO
MIDDLE
2. Select the desired feature using the UP or DOWN button.
• Each time you press the UP or DOWN button, the arrow indicator moves up or down.
• Move the arrow indicator to the desired feature item.
Select the function using the UP or DOWN button.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
AUTO
MIDDLE
SPECIAL
EXIT
Change the status using the LEFT or RIGHT button.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
Notes
• For the mode with you can access submenu.
• You can access submenu using SET button.
Camera ID
If you enter a camera ID, the name will be displayed in the screen monitor.
1. Press the SET button to display the setup menu and move the arrow indicator to 'Camera ID' using the UP or DOWN button.
2. Set 'Camera ID' to 'ON' using the LEFT or RIGHT button.
Notes
• If the camera ID feature is set to 'OFF', the name will not displayed in the monitor.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
SPECIAL
AUTO
MIDDLE
EXIT
Operating Your Camera
3. Press SET button.
Camera ID
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z
- . 1 2 3 4 5 6 7 8 9
CLR POS END
4. You can enter up to 15 characters.
Move the cursor to character-enter location by using the LEFT or
RIGHT button.
Select the desired character by using LEFT, RIGHT,UP or DOWN button.
Camera ID
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z
- . 1 2 3 4 5 6 7 8 9
CLR POS END
Press the SET button to confirm the blinking character. The first character is saved and the cursor in the bottom of the screen moves to the next position.
Repeats steps and until you create the full name you want.
Notes
• If you make a mistake while entering name
Move the cursor to ‘CLR’ and press ‘SET’ button, all characters will be removed.
If you want to correct each character, locate the cursor on the position that you desire to erase using the arrow sign. And correct the character.
COLOR CCD CAMERA
24
User’s Manual
5. Select the position at which the camera ID will be located on the screen.
Move the cursor to 'Pos' and press SET button.
Camera ID
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z
- . 1 2 3 4 5 6 7 8 9
CLR POS END
The camera ID is displayed on the top-left of the monitor screen. (Default position)
FRONT DOOR
Select the position by using the 4-directional buttons, then press the SET button to confirm the position.
FRONT DOOR to Locate, then SET
6. When completed, move the cursor to 'End' and press SET button.
COLOR CCD CAMERA
25
User’s Manual
Operating Your Camera
Backlight
SV-III DSP chip built-in provides intelligent light level control to overcome the severe Backlight conditions.
1. Press the SET button to display the setup menu and move the arrow indicator to ‘Backlight’ using the UP or DOWN button.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
2. SET ‘Backlight’ to the desired mode using the LEFT or RIGHT button.
WDR: In case that bright and dark parts exist on the screen at the same time, your camera allows you to see both parts clearly
OFF: Deactivation
WDR OFF
3. Press the ‘SET’ button.
• When ‘WDR’ is chosen, you can adjust the LIMIT.
WDR SETUP
WDR LIMIT
LOW
Press SET to Return
You can select the level(LOW,MIDDLE,HIGH).
WDR sensitivity is increased or decreased.
4. When completed, press the SET button.
COLOR CCD CAMERA
26
User’s Manual
Notes
• If you select manual in ‘shutter’ menu, you can’t use WDR mode.
• If you select WDR mode, the following phenomenon may appear by lighting condition. In these cases do not select WDR mode.
Unnatural color change or unnatural phenomenon on the screen
Noise of bright part on the screen
• According to the area of bright part on the screen there may be the difference of
WDR performance so be sure to adjust the degrees of the visual angle when installing your camera.
• If you change WDR LIMIT, unnatural phenomenon may appear.
• For the optimal WDR performance, in case of observing the object that is in the place of the changing illumination, recommend to use Auto Iris Lens(Video or
DC type, not manual)
White Balance Control
Your camera provides 3 ‘White Bal.’ control modes. You can select the most suitable one. You can adjust the white balance.
1. Press the SET button to display the setup menu and move the arrow indicator to 'White Balance' using the UP or DOWN button.
2. Set ‘White Bal.’ to the desired mode using LEFT or RIGHT button.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
The four white balance control modes are as follows :
ATW(Auto Tracking White Balance): When color temperature is 1800 ~
10500K, select this mode.
COLOR CCD CAMERA
27
User’s Manual
Operating Your Camera
AWC(Auto White balance Control): The white balance is automatically adjusted in a specific environment. In order to obtain the best result, press the SET button while the camera focuses on white paper. If the environment including the light source is changed, you have to adjust the white balance again.
Manual: To fine adjust, select the Manual mode. You can increase or decrease the red or blue factor while monitoring the difference on the screen. Set to 'Manual' mode and press the SET button. Increase or decrease the value for red(R-Gain) and blue(B-Gain), watching the color of the picture, and press the SET button when you obtain the best color.
Notes
• Proper White Balance may not be obtained under the following conditions, in these cases select the AWC mode.
When the scene contains mostly high color temperature object, such as a blue sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the place of the changing illumination.
Motion Detection
Your camera transmits an alert signal when it detects motion of an object on the screen. If you connect the camera to an external alarm, you can pay attention to the screen when the alarm sounds. This feature is useful when you have to monitor several screens simultaneously.
1. Press the SET button to display the setup menu and move the arrow indicator to 'Motion Det.' using the UP or DOWN button.
COLOR CCD CAMERA
28
User’s Manual
2. Set ‘Motion Det.’ to the ON mode using LEFT or RIGHT button.
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
Press SET button.
Select the two kinds of ZONE NUMBER(1 or 2), ZONE 1 covers larger area than 2.
Turn on ZONE STATE, then MD starts to be activated.
Move the cursor to the desired menu and adjust it. You can increase or decrease the detection area adjusting TOP, BOTTOM, LEFT, RIGHT values.
You can increase or decrease the detection sensitivity adjusting SENSITIVITY value.
COLOR CCD CAMERA
29
User’s Manual
Operating Your Camera
· When completed, press END button.
Notes
Tips on Using the Motion Detection Feature
• After selecting zone and sensitivity, perform a test operation to make sure it works properly.
• If the lighting flickers, the motion detection feature might not work properly.
• The object should occupy 10% or more of its zone. The bigger the object, the higher sensitivity.
• If the brightness of an object changes rapidly by sudden lighting change, the camera may detect it as a motion.
• When this feature is activated, another algorithm may take more time to be operated.
• This system does not guarantee prevention of fires or thefts. The manufacturer is not responsible for any accident or damage.
• You can use the MD output terminal jack on the rear of the camera to connect an external alarm device. For details, see page 40.
DC / Video: When using auto iris lens
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
When using Auto Iris Lens with Video type
Adjust ALC volume on the lens properly. Normally ALC volume should be turned all the way to Av(Average).
According to the type of the lens used, the lens may not perform properly.
In such a case, adjust the volume level on the lens.
For using VIDEO LENS, at first, execute IRIS ADJ(Press ‘SET’ button locating the cursor on ‘IRIS ADJ’). If operation fails, ‘Err Can’t Close : Turn down’ or
‘Iris Test Err Flicker’ message is displayed. Then you should adjust volume level. Until ‘Lens Level Adjustment OK’ message is displayed, adjust volume level repeatly.
Lens Selection
You can set the type of the lens, and control the brightness of the screen.
1. Press the SET button to display the setup menu and move the arrow indicator to 'Lens' using the UP or DOWN button.
2. Set ‘Lens’ to the desired mode using LEFT or RIGHT button.
• You can select from DC / Video, Manual
COLOR CCD CAMERA
30
User’s Manual
Notes
• When trying to execute IRIS ADJ, do it under as below conditions.
- shoot a white paper or bright wall.
- shoot light resource or bright area. (more than 150lux)
COLOR CCD CAMERA
31
User’s Manual
Operating Your Camera
Manual: When using manual lens
Notes
• When the auto iris lens is mounted, you have to set the DC/Video selection switch on the side of the camera properly according to the type of the lens. The setup window displays DC or Video according to status of this selection switch.
(refer to page 12 picture)
• If you select 'DC'/'Video' mode, you can adjust the desired Brightness.
3. When completed move the arrow indicator to ‘END’ and press the SET button.
Shutter Speed Control
You can control brightness of the screen by the shutter speed.
1. Press the SET button to display the setup menu and move the arrow indicator to ‘Shutter’ using the UP or DOWN button.
2. Set ‘Shutter’ to the desired mode using the LEFT or RIGHT button.
A.FLK(1/100 for NTSC Model,1/120 for PAL Model)
: Flickerless mode
ESC: When setting the optimal shutter speed automatically
Manual: When setting shutter speed manually
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
3. If you choose ‘Manual’, select the optimal shutter speed.
COLOR CCD CAMERA
32
User’s Manual
• You can select speed from ‘1/60’ to ‘1/120,000’sec (NTSC Models), ‘1/50’ to ‘1/120,000’sec (PAL Models).
* It is possible to adjust Sens-Up(x2 ~ x128) mode manually.
• When the shutter speed is increased or decreased using the LEFT or RIGHT button, you can find the difference by monitoring the brightness of the screen.
4. When completed, press the SET button.
Notes
• For effective A.FLK mode set WDR mode in Backlight menu to OFF. A.FLK mode is not effective with WDR mode.
• If the camera directly faces strong fluorescent light with 'ESC' mode, the image may become unstable.
• If you choose ‘ESC’, you can adjust the brightness of monitor screen using the
LEFT or RIGHT button.
• If you choose Manual mode, you can’t use WDR mode in ‘Backlight’ menu.
• If you select manual or A.FLK mode, Sense up is not operated.
COLOR CCD CAMERA
33
User’s Manual
Operating Your Camera
AGC (Auto Gain Control)
To get brighter picture.
1. Press the SET button to display the setup menu and move the arrow indicator to ‘GAIN’ using the UP or DOWN button.
2. Set ‘gain’ to desired mode using the LEFT or RIGHT mode.
HIGH: Gain is increased or decreased from 0 to 34dB automatically as following the illumination.
MIDDLE: Gain is increased or decreased from 0 to 27dB automatically as following the illumination.
LOW: Gain is increased or decreased From 0 to 24dB automatically as following the illumination.
OFF: Deactivation
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
AUTO
MIDDLE
SPECIAL
EXIT
Sense up
You can always get the clear image with this function under night or lowlighting level.
1. Press the SET button to display the setup menu and move the arrow indicator to 'Sense up' using the UP or DOWN button.
2. Set ‘Sense up’ to the desired mode using the LEFT or RIGHT button.
Auto: When your camera is under night or low-lighting level, select this mode.
OFF: Deactivation
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
AUTO
MIDDLE
SPECIAL
EXIT
Notes
• If you press the set button on ‘Auto’ mode. You can adjust brightness by increasing or decreasing the shutter speed. (EX. x2,...., x32, x64, ...., x128)
• If you increase the number of shutter speed, moving object gets an more afterimage.
• Under Sense up activated noise, sports or a whitish phenomenon may appear in the picture as the sensitivity of the camera is increased. This is normal phenomenon.
COLOR CCD CAMERA
34
User’s Manual COLOR CCD CAMERA
35
User’s Manual
Operating Your Camera
SSNR(Samsung Super Noise Reduction)
To reduce the noise on the screen.
1. Press the SET button to display the setup menu and move the arrow indicator to ‘SSNR’ using the UP or DOWN button.
2. Set ‘SSNR’ to desired mode using the LEFT or RIGHT mode.
LOW: low reduction of the noise
MIDDLE: middle reduction of the noise
HIGH: high reduction of the noise
OFF: Deactivation
SETUP
CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL.
ATW
MOTION DET.
LENS
OFF
DC
SHUTTER ESC
AGC MIDDLE
SENSE UP
SSNR
AUTO
MIDDLE
SPECIAL
EXIT
Notes
• If you change the ‘AGC’ menu from LOW to HIGH, sensitivity is increased as well as noise on the screen.
• If AGC is OFF, you can’t select LOW/MIDDLE/HIGH on SSNR menu.
SPECIAL
1. Press the SET button to display the setup menu and move the arrow indicator to ‘SPECIAL’ using the UP or DOWN button.
2. Press the SET button.
D-ZOOM: You can select an electronic zoom mode among x2, x4,x8 mode.
- After selecting zoom mode you want, adjust PAN and TILT value by pushing the left or right key to locate the position that you want to see.
COLOR CCD CAMERA
36
User’s Manual COLOR CCD CAMERA
37
User’s Manual
Operating Your Camera
PRIVACY: To mask area which you want to mask
- OFF: Deactivation
- ON: Privacy mode activated
· Press the SET button.
· 4 AREAS are selectable. Select the area you want(AREA1, AREA2, AREA3,
AREA4)
· Set AREA STATE ‘ON’ using LEFT or RIGHT button.
· Make the size of PRIVACY AREA by changing TOP, DOWN, LEFT, RIGHT values.
DAY/NIGHT: choose color or B/W mode.
- COLOR : color mode
- B/W : B/W mode
- EXT : It enables user to control DAY/NIGHT mode by Inputing external signal.
- AUTO : Under general condition, D/N filter is fixed at DAY mode, but under low luminance condition, it change into NIGHT mode automatically. The case of the opposition is also same.
COLOR CCD CAMERA
38
User’s Manual
Notes
• When you use Auto Iris Lens with Video type, do not set the level on the lens to too low, Color/BW may not change over automatically.
• When Gain in SET UP menu is OFF, Color / BW do not change over automatically.
• If AGC is OFF, you can’t select AUTO mode on DAY/NIGHT menu.
• For the stable operation, whenever the mode is changed over between color and BW mode, five setup menu buttons on the camera do not operate for about 3 seconds.
• It is possible to turn on or off the burst signal on B/W mode.
• The object may be more out of focus when using a source of near-infrared light than using the visible light.
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and
EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronizes the video signal between cameras without a synchronous generator. The line-lock synchronization is only used in the areas of 60Hz (NTSC
Models) / 50Hz (PAL Models).
- INT : Internal synchronization - LL : External line-lock synchronization
· If you choose ‘LL’, you can adjust the desired phase. Press the SET button.
-You can adjust the desired phase from 0 to 359.
Notes
• When the power frequency is 50Hz, you can not use line-lock mode(NTSC Models).
• When the power frequency is 60Hz, you can not use the line-lock mode(PAL Models).
• ‘Sync.’ mode is fixed to ‘INT’ in DC 12V input power.
COLOR CCD CAMERA
39
User’s Manual
Operating Your Camera
IMAGE ADJ: This includes the factors related to the image quality or special function.
- H-REV : Set ‘ON’, then each side of image(left and right) is exchanged on vertical axis.
- V-REV : Set ‘ON’, then image changes upside down.
- TONE : As you increase the value using left or right button the whole level would be brighter.
- SHARPNESS : As the value goes high, edge of image become strong and obvious. But if increasing the value too much, some noise may appears on image and image may looks unnatural.
- COLOR : As you increase or decrease the value, image chroma level increases or decreases but the burst level doesn’t.
PRESET: To reset your camera to factory default condition
RETURN: To move Top-menu
EXIT: To finish setting menu
Notes
• the reflected letters on mirror will be seen when activating H-REV or V-REV.
Using Remote Jack / MD Output / D&N Input
If you connect a remote plug to the REMOTE jack on the rear of the camera as shown below, you can access the menu setup mode from a remote place.
COLOR CCD CAMERA
40
User’s Manual
1. RS-232C Communication Setting.
• Mode : Serial • Data Bit : 8 • Bit/sec : 9600bps • Stop Bit : 2
• Port : Com1 • Parity : None • Flow Control : XON/XOFF
2. Setup menu Command.
Setup menu
Set
Up
Down
Right
Left
Command
153
65
66
67
68
Byte
1
1
1
1
1
3. MD(Motion Detection) output Signal Level(less than 10mA)
+4.0V~+5.0V
There is motion
0V
There is no motion
5±0.5sec
4. D&N input Control Signal
If you want to use EXT mode, consist proper system that satisfy below condition
• For DAY mode, D&N terminal should be open from external signal
• For B/W mode, D&N terminal should be short to ground.
Notes
• You must turn the camera power off when you connect or remove the remote plug.
COLOR CCD CAMERA
41
User’s Manual
Troubleshooting
If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician.
Problem
Nothing appears on the screen.
The image on the screen is dim.
The image on the screen is dark.
The camera is not working properly, and the surface of the camera is hot.
Solution
• Check that the power cord and line connection between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
• Check that the DC/VIDEO selection switch on the side of the camera is set to a proper position according to the type of your auto iris lens.
• Are you using Auto Iris Lens with VIDEO type?
Adjust VR Level properly (refer to page 31)
• Is lens stained with dirt? Clean your lens with soft, clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change the camera position.
• Adjust the lens’ focus properly.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω / Hi-z properly. (refer to page 19)
• Are you using the Auto Iris Lens? Adjust the level on the lens properly.
• Check that you have properly connected the camera to an appropriate power source. (refer to page 20)
COLOR CCD CAMERA
42
User’s Manual
Problem
Motion Detection function is not active.
The color of the picture is not matched.
The image on the screen flickers.
L/L mode isn’t able to be selected.
L/L is not operating properly.
Solution
• Have you set ‘Motion Det.’ menu to OFF?
• Have you set ‘SENSITIVITY’ to too low?
• Have you set ‘MD Area’ properly?
• Check that you have properly set the ‘White Bal.’ menu.
• Is the camera facing to direct sunlight or fluoresent lighting? Change the camera position.
• Are you using Auto Iris Lens? Check that you have properly connected the lens plug to the Auto Iris connector on the side of the camera.
• Have you connected your camera to DC power source? Connect it to AC power source.
• Check the frequency of power supply.
(60Hz for NTSC, 50Hz for PAL)
COLOR CCD CAMERA
43
User’s Manual
Specifications n c.
S y
POWER
Total Pixels
C
C
D
Effective Pixels
Size
Scanning System
Synchronization
Frequency
Resolution
Video Output
S/N (Y signal)
Min. Illumination
I
C
T
R
A
L
E
C
E
L
WDR
Day & Night
Gain Control
White Balance
Electronic shutter speed
Sens-Up
O.S.D
Motion Detection
RS-232C
SSNR
FLIP
D. ZOOM
Privacy Function
IRIS Control
Lens Mount
Dimension
Operating temperature
Operating Humidity
Weight
NTSC (SHC-730N) PAL (SHC-730P)
AC24/DC12(±10%), 4.5W
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
1/3 inch, Vertical double density interline CCD
2:1 Interlace
Internal/Line Lock
Horizontal:15.734KHz, Vertical :59.94Hz
Horizontal: 15.625KHz, Vertical : 50.00Hz
520TV Lines(Min.);Color, 570TV Lines(Min.);B/W 520TV Lines(Min.);Color, 570TV Lines(Min.);B/W
1.0Vp-p/75Ω(Video 0.714Vp-p, Sync 0.286Vp-p) 1.0Vp-p/75Ω(Video 0.7Vp-p, Sync 0.3Vp-p)
52dB (AGC Off,Weight ON)
0.13Lux/F1.2 at Color(50IRE), 0.01Lux/F1.2 at BW(50IRE)
52dB
COLOR / BW/AUTO (Filter Auto Change) / EXT
(External Day/Night mode control capability via terminal at the back panel)
Low,Middle,High,OFF Selectable
ATW/AWC/Manual (1800˚K ~10,500˚K)
AUTO/MANUAL (1/60 ~ 1/120,000sec) AUTO/MANUAL (1/50 ~ 1/120,000sec)
ON/OFF (selectable limit~X128)
Built-in
ON/OFF (Built-in Alarm output connector)
Built-in
Low, Middle, High, OFF Selectable
Built-in (Up/Down, Left/Right)
Built-in (~x8, Pan Tilt)
ON/OFF (4 Programmable Zone)
DC / Video
CS Mount (Easy Focus type)
(C-Mount is mountable by using adaptor)
70(W) X 56(H) X 130(D)mm
-10˚C ~ +50˚C [14˚F ~ 122˚F]
Max 90% RH
480g
COLOR CCD CAMERA
44
User’s Manual
DECLARATION OF CONFORMITY
Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
Model Name
Beginning Serial NO.
Year of Manufacture
Conformance to
CCTV Camera
SHC-730P
S4120001
2004. 12. 01
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name
Position
YOUNG TAEK SON
QUALITY CONTROL MANAGER
Full Name
Position
Place
Date 2004. 12. 01 Date
MEMO MEMO
advertisement
Related manuals
advertisement