DiyTracker REAL TIME GPS TRACKING ANDMONITORING SYSTEM User's Manual Installation And Operating Instructions

DiyTracker REAL TIME GPS TRACKING AND MONITORING SYSTEM is a reliable and user-friendly device that provides real-time tracking and monitoring of vehicles, allowing for peace of mind and enhanced security. Its advanced GPS technology ensures accurate location data, and its compact design enables discreet installation on motorcycles. With features like remote control arming and disarming, automatic arming, and panic button activation, DiyTracker offers comprehensive protection and control over your motorcycle.

PDF

Dokumen

REAL TIME GPS TRACKING AND

MONITORING SYSTEM

User’s Guide

Installation and Operating Instructions

It’s LIV

E racking

Anytim e, here in

REAL TIM

Intro duction

Thank you for purchasing our “DiyTracker”

Each unit has been manufactored to the highest quality to ensure reliability and ease of use.

Before Installing

This guide covers the installation of the DiyTrack device to ensure a safe and functional install of the unit by either a

Professional or novice installer

Prior to the installation process, thoroughly review this guide and adhere to the following:

- Use only a Digital or Analog Volt Meter - DO NOT USE TEST LIGHT!

- Check for possible installation locations for the tracker unit prior to permanent installation.

- Make sure that the installation process does not cause damage to any motorcycle hose, electrical loom,

or cause physical damage to the motorcycle

- Make note of the unit mobile and serial numbers prior to installation.

- Prior to installing this device, disconnect the motorcycle battery

- Make sure the device and all associated cables are securely mounted and do not impede any of the motorcycles’s controls.

- Ensure all connections are properly soldered and insulated, all un-used cables must be properly insulated.

- Use high quality electrical tape and shrink tubing were necessary motorcycle panel disassembly, and any other mechanical aspects of the motorcycle

GPS Fundamentals

There is a minimum of 24 operational GPS satellites at all times. The satellites, operated by the U.S. Air Force, orbit the earth every

12 hours. Each GPS satellite transmits data that indicates its location and the current time. All GPS satellites synchronize operations so that these repeating signals are transmitted at the same instant. The signals, moving at the speed of light, arrive at a GPS receiver determined by determining the amount of time it takes for their signals to reach the receiver.

When the receiver determines the distance to at least four GPS satellites, it can by triangulation, calculate its position in

three dimensions.

To ensure the GPS unit receives enough satellite signals at an acceptable signal strength, it must be mounted so that it has a clear view of the sky. In hidden locations, such as under the fairing or seat, it is important to keep any metal interference as far as possible from the top portion (map picture) of the GPS unit so that the most accurate position can be calculated.

While GPS data collection has improved in ease and speed, some obstacles remain. Solid or dense objects can block GPS signals.

Wet trees with heavy branches and leaves can mask or attenuate GPS signals. Mountains and buildings can block satellite transmission. users should be aware of obvious multipath environments.

All GPS Trackers require a SIM card

To get the location data from the GPS tracking unit to a users computer some transmission channel is required.

The Tracker uses GPRS and only sends a very small amount of data.

Hardware & Accessories

Contents of the Box

1. DiyTrack TellMe Pro Tracking Unit

2. Wiring harness with input and output cables

3. Relay

4. Microphone

5. Remote Control

Tools Needed for Installation

• Metric and standard socket set

• Scre w dri v er set

• Side cutters, wire cutters

• W ire strippers

• Pliers

• T erminal crimpers

• Digital Multimeter

• Electrical tape

• Flashlight

• Soldering iron and solder

Correct wire/cable joining method

Solder and insulate all connections. (Crimping should be avoided wherever possible.)

WARNING It is highly recommended that a Digital Multimeter be used when probing electrical systems on a motorcycle to prevent damage to factory components.

Installation Process

Installing and Mounting the GPS Unit

To ensure the GPS unit receives enough satellite signals at an acceptable signal strength, it must be mounted so that it has a clear view of the sky. In hidden locations, such as under the fairing or seat, it is important to keep any metal interference as far as possible from the top portion of the GPS unit so that the most accurate position can be calculated.

Ensure the “gps Antenna area” is “face up” towards the sky

Any metal objects between the GPS Antenna Sensing Area and the satellites will degrade the signal and reduce the overall performance.

The TellMe unit can be installed in any type of motorcycle. The unit should be mounted so it will not be exposed to or get damaged from people or objects.

“Face Up”

Wiring Diagram

Wire

Description

Power

Digital Output

Digtal Input

Microphone

RF Receiver

Antenna

Pin No. Wire Color

Red

Black

Orange

Blue

Grey

Yellow

Brown

Orange

Grey

Blue

Green

Red

Green

Black

Function/Specification Description

Power positive pole, 8-60V DC

Negative / Ground

Future Use

Engine Immobilizer

Ignition status Detection

Future Use

Panic Button

Future Use

Mic+

Mic-

3.3V Power

RF Data

Ground

10amp fuse GND

+12/24v

GND i c

Power cut relay (Optional connection)

This connection is to remotely immobilise your vehicle. Please be cautious if installing this optional immobiliser function as large currents are carried when starting a motorcycle and we would hate for you to have an unplanned stop due to an installation failure.

A. Connect Pin6 grey wire/cable to the yellow wire/cable (86) of the relay

B. Connect the white wire/cable (85) of the relay to a constant 12/24v source

C. Cut the positive wire of the motorcycle ignition coil / fuel pump / solenoid etc

D. Connect the green wire of the relay (30) to one end of the positive wire that you cut

E. Connect the green wire of the relay (87a) to one end of the positive wire that you cut

Relay

87a

+12/24v

Ignition Coil

Fuel Pump

Solenoid

Remote Control

Arm

Panic (Siren)

Disarm

Mute

Arm: Buzzer sounds once

Disarm: Buzzer Sounds Twice

Mute Key: Press this button to stop/mute the siren.

In panic, Activate Siren to sound. Or in parking lot, press this button for to locate the motorcycle

Remote Control / Transmitter OVERRIDE

If your transmitter is damaged, or the transmitter battery is flat, the system can be overridden by Ignition switch in conjunction with the Panic Button.

Please follow the below process to override the remote control / transmitter

1. Send an SMS command to clear all existing transmitter codes which is stored in the system

2. Disarm the system by SMS command

3. Press and Hold Panic button

4. Switch Key from ACC off to ON position continuously 7times

5. Buzzer will sound once to indicating Overridden mode has been entered

6. Press any button of the transmitter

7. Buzzer sound twice again to indicate override success and exit overridden mode

If the system enters into override mode, and no transmitter button was pressed or did not receive any incoming signal within 20seconds, buzzer will sound bibibi three times and the system will exit override mode

If you pressed the transmitter button during override mode, but system failed due to an unexpected reason, the system also will sound bibibi three times to indicate failure.

Installation Process

12/24v Power/Positive Connection (Red Wire)

Disconnect the negative terminal from the motorcycle battery to prevent a possible transient voltage surge that will damage your traking unit. Please note warranty does not cover damage from transient voltage surge.

Securely attach the wiring harness to the Tracking unit

12-24V DC Power Connection (Red Wire)

Locate the Red wire found on the wiring harness. The red wire must be connected to a constant

12 volt source from the motorcycle to power the tracker unit.

It’s important that the12 volt power source maintains 12 volts at all times.

Ground Connection (Black Wire)

Locate the Black wire found on the wiring harness

The black wire must be connected to the negative terminal of the motor cycle battery.

Re-connect the negative terminal to the motorcycle battery and proceed to the next step

Optional Connection

Switched Ignition 12/24v Connection

(Yellow Wire )

Locate the Yellow wire found on the wire harness supplied with your Tracking unit.

The Yellow must be connected to a switched 12/24v source from the motorcycle.

How to Find (+) 12/24v Ignition with a Multi Meter

1. Set your meter to DCV or DC voltage

2. Attach the (-) negative probe of the meter to the chassis ground

Your meter should read (+) 0v

4. Turn the ignition key to the “ON” position. If your meter reads (+)12/24VDC go to the next step, if not probe another wire.

5. Now turn the key to the start position. The meter display should stay steady (+) 12/24v, not dropping by more than a few tenths of a volt. If it drops close to or all the way to (0) zero, go back to step 3, If it stays steady at (+) 12/24v you have the ignition wire.

WARNING Solder and insulate all connections (Crimping should be avoided wherever possible)

Remote Control

ARMING AND DISARMING THE SYSTEM

To ARM the system To DISARM the system

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Automatic Arm:

The system can be configured to allow automatic Arming, it will arm automatically 8 Minutes after ignition is switched OFF, or you can arm the system manually before this time. If the system was Disarmed when ignition is OFF, it will arm automatically after 8 Minutes either way.

You can able this "AUTOMATIC ARM" function by SMS command. Factory Default is disabled

To Enable To Disable

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Testing & Troubleshooting

After the TellMe tracking unit has been powered on for atleast 5 minutes, dial the tracker simcard mobile number that is inserted in your tracking unit. Let it “ring” 3 times then hang up.

Now send the following SMS to the simcard mobile number that is inserted in your tracking unit:

*1234*P#

Please note the above SMS must be sent exactly like the example and all letters must be UPPER CASE

If the ITellMe tracking unit has been correctly installed and the GPS antenna has successfully fixed onto the satellites, then you will receice a SMS text message back from the TellMe tracking unit containing a “clickable” google map link showing you the current location of your motorcycle.

If no GPS fix has been acquired by the time the tests are complete, then verify that the TellMe tracking unit has been installed correctly and that there is NO metal blocking the signal between the GPS antenna and the sky and that motorcycle is outside.

SYMPTOM

Unit Does Not Power-up

CAUSES

Power is not connected to the unit. With a Digital Volt

Meter, measure the voltage at the input to the unit. A positive voltage should be measured on the + terminal of the unit when measuring between the + terminal and the - terminal or chassis ground. This voltage should also measure 12/24v. Correct the wiring to assure the correct polarity and the correct voltage level.

The main cause of this is poor signal strength due to shielding. Move the motorcycle outside the building ,

Unit Does Not Find

Cellular Service after 5min re-apply power to the unit.

Unit Does Not Receive a GPS Signal The cause is that the GPS receiver is not locking into the satellites. The main cause is due to the unit not receiving the signal from the satellites. Make sure that the unit “face up”is facing towards the sky.

If it is, then move the motorcycle outside of any building/garage to allow the GPS unit to have a clear view of the sky.

SMS Commands

Setting alarm alert numbers

The alarm alert numbers will receive SMS alerts such as panic alert and accident alert

A total of 3 mobile numbers can be programmed into the tracking unit to receive alerts

Replace [mobilenumber] with your own mobile numbers.

*1234*A 44mobilenumber *B 44mobilenumber *C 44mobilenumber #

Example SMS: *1234*A44721273167*B44789292882*C44843623686#

The mobile numbers “ 0721273167 and 0789292882 and 0843623686 will now be the authorised numbers

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

In Armed status, any illegal operation will trigger an alarm action. The system siren(buzzer) will sound for 15 seconds, and will also send alarm alert via SMS text and missed call to preset phone numbers A/B/C.

Please see following alarm events

Activate Accident Alert

Recipient numbers B+C will receive an SMS should the motorcycle be in an accident.

1st Set: *1234*CS*7,7,7#

*1234*GON#

*1234*GOFF#

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

SMS Commands

Immobilize the bike

If the relay is installed (see page 7) then an alert number can send SMS commands to the TellMe unit to immobilise the motorcycle.

To immobilise the motorcycle :

Send SMS: *1234*stop#

To restore power to the the motorcycle :

Send SMS: *1234*K#

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Auto Immobilize

Upon Alarm in armed status, the system will automatically activate the immobiliser function to immobilise the motorcycle.

To activate automatic immobilizer function.

To Enable To Disable

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Movement Alert

The system will detect all X,Y,Z acceleration, any changes in all X,Y,Z axis will be calculated, all changes which is over

0.1G, the system calculates as movement, the system scans and calculates every 5 Seconds

SMS commands for adjusting sensitivity

SMS:

NOTE:

*1234*VS*xxx# value xxx range from 1 - 200

1=most sensitive

200= Most insensitive

Default = 30

To Enable Alert To Disable

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

SMS Commands

S leep mode settings

Simple Sleep when Ignition Off:

GSM Sleeps with SMS/Call Active, NO GPRS Connection and GPS shut down

All Alarms Detection are active, if an an alarm is triggered the device will wake up to normal working mode.

Power Consumption in standby without alarm trigger: 10mA

Deep Sleep when Ignition Off:

GSM Sleeps with SMS/Call NOT Active, NO GPRS Connection and GPS shut down

Alarms trigger detection: Off 6seconds, detect 2seconds

if an an alarm is triggered the device will wake up and Fix a GPS location and process all alerts

Average power consumption without alarm trigger: <5mA

NO sleep when Ignition Off:

Please note:

*1234*SL*C#

GSM all ON with SMS/Call active, and GPRS connected with Server with continuously data sending

GPS ON

All alarm detection work normally

The SMS must be sent exactly like the above example with NO spaces and all

Voice monitoring mode (Voice Surveillance)

When the INFORMA receives this command from an authorised number, the unit will call back the authorised number that sent the command. Once the authorised number picks up the INFORMA will enter surveilance mode, the driver will not know that the authorised number is “listening in”

Replace [mobilenumber] with your own mobile number.

*1234*VM 44mobilenumber #

Example: If the user that wants to “listen in” cell number is 0829601981 then the user must send from that mobile phone the following SMS to the INFORMA tracking unit.

Example SMS: *1234*VM447951241136# note: If the unit failed to call you back please add the international code. example *12324*VM+447951241136#

Please note:

The SMS must be sent exactly like the above example with NO spaces and al

Speeding Alert

When the vehicle speed exceeds the preset value the tracker will send an SMS alert to the authorised numbers

Example SMS: *1234*SPD120#

Should the speed exceed 120 Km/h then an SMS will be sent to the authorised numbers.

NOTE: value range from 000 - 999 Km/h

000 means cancel over speed alert.

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

SMS Commands

Set Local Time

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Get Co-ordinates with Gmaps link

The authorised number will receive an SMS with the location co-ordinates of the vehicle and a clickable

Google Maps link. perfect for tracking on a cell phone with internet availability.

Send SMS: *1234*P#

Example text reply:

356823032252491

Clickable link

Lat:+ 50.723855

Lon: -3.531958

Speed:1.11KM/H http://maps.google.com/maps?q=+50.723855,-3.531958

Please note:

The SMS must be sent exactly like the above example with NO spaces and all

Warranty & Disclaimer

Warranty

Diy-Track warrants, to parties purchasing Diy-Track equipment directly from Diy-Track i.e., to its authorized distributors and to no other parties, that for 12 months following the date of purchase,

Diy-Track equipment will be free of defects in materials and workmanship when installed, operated, maintained, and serviced in strict accordance with Diy-Track and, if applicable, the manufacturer’s requirements.

If Diy-Track equipment fails because of a defect in materials or workmanship within the warranty period,

Diy-Track will, at its sole option and at no charge, repair or replace it.

Diy-Track agreement to repair using new or reconditioned parts or replace with a comparable new or reconditioned Diy-Track unit is the exclusive remedy with respect to Diy-Track Equipment found to be defective in materials or workmanship; this remedy will not be deemed to have failed of its essential purpose so long as Diy-Track is willing and able to repair or replace the defective unit as provided above or, at Diy-Track sole option, to refund the purchase price paid.

Parties purchasing Diy-Track equipment from a distributor are referred to the distributor with respect to any product claims they may have.

THE FOREGOING WARRANTY IS LIMITED AND IS THE ONLY WARRANTY OFFERED.

DIY-TRACK MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION,

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

TITLE, NON-INFRINGEMENT, AND NON-OBSOLESCENCE. THE FOREGOING WARRANTY FURTHERMORE DOES

NOT COVER DIY-TRACK DEVICES THAT (A) HAVE BEEN IMPROPERLY INSTALLED, MAINTAINED, OR

SERVICED; (B) HAVE BEEN TAMPERED WITH OR DEFACED; OR (C) HAVE BEEN SUBJECTED TO ABUSE

(D)TRANSIENT VOLTAGE SURGE OR A HOSTILE OPERATING ENVIRONMENT.

No Warranty – Services

ALL SERVICES ASSOCIATED WITH DIY-TRACK DEVICES INCLUDING, WITHOUT LIMITATION, NETWORK CONNECTIONS ENABLED

BY DIY-TRACK, ARE PROVIDED STRICTLY AS-IS, WITHOUT WARRANTY OF ANY KIND INCLUDING, WITHOUT LIMITATION

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON-INFRINGEMENT, NON-OBSOLESCENCE,

NON-INTERRUPTION, AND FREEDOM FROM ERROR.

IN THE EVENT OF A CLAIM UNDER THIS WARRANTY THE RECEIPT/PROOF OF PURCHASE MUST BE PRODUCED TOGETHER

WITH THIS WARRANTY.

Model Number:__________________________________________

Date of Purchase:_________________________________________

Place of Purchase:_________________________________________

Disclaimer

The use of a GPS vehicle tracking device to track a person without their permission could be illegal or result in a legal action against you, even if you own the vehicle. Tracking another person or their property is usually illegal without their permission and/or a warrant. You should seek legal advice before using any GPS vehicle tracking device as the regulations vary from country to country

We are not responsible for acts or omissions of any other service provider, for information provided through the equipment, for use of or installation of Diy-Track products unless caused by the sole and gross negligence of Diy-Track

Halo! Saya adalah chatbot AI yang secara khusus dilatih untuk membantu Anda dengan DiyTracker REAL TIME GPS TRACKING ANDMONITORING SYSTEM User's Manual Installation And Operating Instructions. Saya telah meninjau dokumen secara menyeluruh dan dapat membantu Anda menemukan informasi yang tepat yang Anda butuhkan atau menjelaskan konten dengan istilah yang jelas dan sederhana. Apakah Anda mencari panduan tentang fitur tertentu, langkah-langkah pemecahan masalah, atau penggunaan umum, jangan ragu untuk mengajukan pertanyaan Anda. Semakin banyak detail yang Anda berikan tentang kekhawatiran atau kebutuhan Anda, semakin akurat dan efektif saya dapat membantu Anda!

Tampilkan petunjuk terkait

Asisten sedang mengetik

Asisten sedang tidak ada di depan keyboard. Silakan coba lagi nanti.

Pertanyaan yang sering diajukan

The DiyTracker is a real-time GPS tracking and monitoring system that provides vehicle tracking and monitoring capabilities.

The DiyTracker box includes the DiyTrack TellMe Pro Tracking Unit, wiring harness with input and output cables, relay, microphone, remote control, and instruction manual.

The DiyTracker unit should be mounted in a location with a clear view of the sky to ensure optimal GPS signal reception.

Connect the red wire of the wiring harness to a constant 12-volt power source, and the black wire to the negative terminal of the motorcycle battery.

Connect the yellow wire of the wiring harness to a switched 12/24v ignition source.

To arm the system, send an SMS message with the code '1234S#'. To disarm the system, send an SMS message with the code '1234C#'.

Yes, the DiyTracker system can be configured for automatic arming. To enable this feature, send an SMS message with the code '1234AUTOARMON#'. To disable it, send an SMS message with the code '1234AUTOARMOFF#'.