1
GSM/GPRS/GPS Vehicle Tracker
GPS103B User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.
2
Contents
1.
Introduction ........................................................................................................................ 3
2.
Hardware Description ......................................................................................................... 3
3.
Accessories Name ............................................................................................................... 3
4.
Specifications...................................................................................................................... 4
5.
Operating Instructions ........................................................................................................ 5
6.
Function setting .................................................................................................................. 7
6.1
Initialization ..................................................................................................................... 7
6.2
Change 123456 ................................................................................................................ 7
6.3
Authorization ................................................................................................................... 8
6.4
Single Tracking ............................................................................................................... 8
6.5
Continuous Tracking Automatically ............................................................................... 8
6.6
LBS Tracking .................................................................................................................. 9
6.7
Modes switch between “track” & “monitor” .................................................................. 9
6.8
Data logging .................................................................................................................... 9
6.9
Alarms ........................................................................................................................... 10
6.9.1 Low battery alarm ........................................................................................................... 10
6.9.2 Power off alarm............................................................................................................... 10
6.9.3 GPS blind Spot alarm...................................................................................................... 10
6.9.4 SOS alarm ....................................................................................................................... 11
6.9.5 Geo-fence alarm .............................................................................................................. 11
6.9.6 Movement alarm ............................................................................................................. 11
6.9.7 Overspeed alarm ............................................................................................................. 12
6.9.8 ACC working alarm ........................................................................................................ 12
6.9.9 Vibration alarm ............................................................................................................... 12
6.9.10 Set all alarm mode ........................................................................................................ 13
6.10
Cut off the Oil and Power System ............................................................................. 13
6.11
Resume the Oil and Power System ............................................................................ 13
6.12
Arm ............................................................................................................................ 13
6.13
Function of Remote Controller (Option) ................................................................... 14
6.14
Disarm ........................................................................................................................ 14
6.15
Silent Mode ................................................................................................................ 15
6.16
Switch between GPRS and SMS Mode ..................................................................... 15
6.17
Check the Vehicle State ............................................................................................. 15
6.18
Device Resetting ........................................................................................................ 16
6.19
IMEI Checking........................................................................................................... 16
6.20
Time Setting ............................................................................................................... 17
6.21
TCP/UDP switch ........................................................................................................ 17
6.22
GPRS Setting ............................................................................................................. 17
6.22.1 Set APN ..................................................................................................................... 17
6.22.2 Set IP and Port ........................................................................................................... 18
6.23
Set up monitor central number ................................................................................... 18
7.
Cautions ............................................................................................................................ 18
8 ． Faults & the Solutions ...................................................................................................... 19
3
1.
Introduction
This tracker is a new product based on the GSM / GPRS network and GPS satellite positioning system, which set multiple functions of security, positioning, monitoring surveillance, emergency alarms and tracking in its entirety. It can track and monitor remote target by SMS or internet.
2.
Hardware Description
① . USB jack
② . External Connection jack
③ . Power/GSM/GPS LED indicator
④ . Monitor jack
⑤
.GPS Antenna jack
⑩
. Remote control receiver antenna
（
Option
）
3.
Accessories Name
4
NO.
1
2
3
4
5
8
4.
Specifications
Content
DIM.
Weight
Network
Band
GSM/GPRS Module
GPS Module
GPS Sensitivity
GPS Accuracy
PHOTOES NAME
GPS Antenna
GSM Antenna
Microphone
Power wire
Relay
Remote control specifications
81.8mm x 35.7mm x 60.3mm
60g
GSM/GPRS
850/900/1800/1900Mhz
MT6260A
Ublox7020
-159dBm
5m
NOTE
3 meters
3 meters
1.5 meters
10PIN
12V/40A
1
5
GPS Start time
Cold status 45s
Warm status 35s
Hot status 1s
Voltage of car power system
Backup battery
Storage Temp.
Operation Temp.
Humidity
5.
Operating Instructions
12 V-24V
Chargeable changeable 3.7V 500mAh Li-ion battery
-40°C to +85°C
-20°C to +65°C
5%--95% non-condensing
5.1 Terminal Installation
5.1.1 Please ask the qualified engineers to install it.
5.1.2 Do not install it in a environment which is more than GSM performance,
And please pay attention to fix the antennas in a exactly position with good signals.
5.1.3 Pay attention to make installation location preventing water and dust.
5.1.4 Find the 10 PIN harness and insert it into the corresponding holes of the products, and connect the wires with the original car circuit showing below:
6
Wiring diagram
5.1.5
Note: The blue wire can be connected to the original car alarm horn;
5.1.6 Know about the type of the door trigger is positive or negative trigger.
Please connect the orange wire to the door control circuit if it is positive, and connect purple wire if it is negative.
5.1.7 Please install the SOS button on the place driver can touch.
5.1.8 Insert the external monitor Microphone into the monitor jack.
5.1.9 Connected the GPS and GSM antenna to the right jack, and find a appropriate place and fix the antennas to make sure it receive signals very well.
5.2 SIM CARD Installations
5.2.1 Use a tweezers or a sharp thing to touch the SIM CARD popup switch, the
SIM CARD slot will pop up, take out the SIM card slot and put SIM card in it. And then put the SIM card slot back to its original position after
7 confirm the SIM card in the right place.
5.2.2 Please make sure that the SIM card is able to execute the function of incoming calls display, no calls can be diverted and the PIN code is locked. The SMS format must be TXT format, and can’t recognize the
PDU format.
5.3 Turn on the Tracker Device.
5.3.1 Connect the positive and negative wire, red and black ones, with 12V or
24V car power system, wait for 1 minute after connecting power to wait tracker works normal.
6.
Function setting
6.1
Initialization
Send SMS “ begin+123456
” to the unit, it will reply “BEGIN,CONFIG OK ” and initialize all the settings to default factory settings.
（ default 123456:
123456
）
For example: send SMS “begin123456”, it will reply “BEGIN,CONFIG OK ”.
The “+” in the command, please don’t type “+”, space means press the space keyboard on your cell phone.
6.2
Change 123456
6.2.1 Send SMS “ 123456+password+space+new password ” to the unit to change the 123456.
8
For example: send SMS “123456123456 888888” to the unit. If succeeded,
“123456,CONFIG OK” will reply to your cell phone from the device tracker.
6.2.2 Make sure the new 123456 is in 6 digits, or else the tracker cannot recognize the 123456.
6.3
Authorization
There are 5 numbers to be allowed to authorize in the tracker at most.
6.3.1 Authorization: Send SMS“ admin+123456+space+cell phone number ” to set up an authorized number, the other central number should be set by the first authorized number, if the number is successfully authorized, the unit will reply”
ADMIN,CONFIG OK” by SMS.
6.3.2 Delete authorization: Send SMS“ noadmin+123456+space+authorized number
” to delete the authorized number.
6.4
Single Tracking
Make a missed call or send SMS “ smslink123456 ” to device number, it will reply a real time tracking message include Long & Lat info.
6.5
Continuous Tracking Automatically
6.5.1
Send SMS command “ ITV+123456+space+moving time interval+space+static time interval ” to the tracker device.
6.5.2
For example: send SMS “ITV123456 10 500” it will report data to server
9 at 10s time interval when vehicle is moving; 500s time interval when vehicle is static.
6.6
Cell ID Tracking
6.6.1 You must set up the APN of your local GSM network for the SIM card in tracker first before using this function, if there is user name and 123456 for
GPRS login, Please refer to following to configure the APN, user name and
123456 for GPRS login.
6.6.2 After configure the APN, send SMS “ cell+123456 ” to device, it will reply
SMS with nearest GSM tower cell ID info. (This function need platform support )
6.7
Modes switch between “track” & “monitor”
6.7.1 The default mode is “track” (track mode).
6.7.2 Send SMS command " monitor+123456 " to tracker device of vehicle terminal, it will reply "MONITOR,CONFIG OK" and switch to “monitor” mode. In this mode, the user can dial up the tracker device to monitor the voice.
6.7.3 Send SMS command " tracker+123456 " to tracker device of vehicle terminal, It will return "TRACKER,CONFIG OK" and restore to “track” mode.
6.8
Data logging
6.8.1 Auto logging
：
When the tracker device lost GSM signals or fall offline from GPRS, tracker will log the tracking position and alerts automatically in the
10
SD card on the basis of the pre-set condition, when GSM signals get back, all the event alerts will be auto-sent to the authorized numbers or monitoring platform (server), but the logged tracking data should be loaded to the monitoring platform via SMS command. ( Must insert TF card )
6.9
Alarms
Note: All Alarms will be sent to Central Number
6.9.1 Low battery alarm
6.9.1.1 Send SMS “ lowbat+123456+space+1 ” to activate the function, it will send SMS“low battery+latitude/longitude” to central number when voltage of battery is below about 3.6V.
6.9.1.2 This function disactivates as default, send SMS “ lowbat+
123456+space+0
” to deactivate.
6.9.2 Power off alarm
6.9.2.1 Send “ extpower+123456+space+1 ” to activate, it will send SMS
“power alarm+latitude/longtitude” to central number when external power is cut off.
6.9.2.2 This function disactivates as default. Cancel: Send SMS “ extpower+
123456+space+0 ” to deactivate it.
6.9.3 GPS blind Spot alarm
6.9.3.1 This function disactivates as default, send SMS “ gps+
123456+space+1 ” to activate the function, it will send alert SMS “no gps+last
11 valid latitude/longitude before lost signal”
6.9.3.2 Send SMS “ gsm+123456+space+1 ” to deactivate.
6.9.4 SOS alarm
Long Press the SOS button for 3 seconds, （ press button on remote controller for 3 seconds
）
, the tracker device will send SMS
“ help me!+lat./long.” to all the central number.
6.9.5 Geo-fence alarm
Set up a geo-fence for the tracker device to restrict its movements within a district. The unit will send SMS to the central number when it detects alarm.
Remark: 0 represents close alarm; 10 represents out fence alarm; 01 represents enter fence alarm; 11 represents out and enter fence alarm.
6.9.5.1 Set Up:
Send SMS“ stockade+123456+space+semi-diameter+space+alarm type
” to unit to set the restricted district. In case of breach, it will send SMS
“stockade!+geo-info” to the central number.
For example: send SMS “stockade000000 500 1” stands for based on device current coordinates as center, 500 is semi-diameter, set 1 as out fence alarm type.
6.9.5.2 Cancel: Send SMS “ nostockade+123456 ” to deactivate this function.
6.9.6 Movement alarm
Device will send movement alarm once vehicle moved 100 meters. The function is default activate if detected vehicle ACC ON. When vehicle ACC
12
OFF stands for closing movement alarm.
(Note: this function must connect ACC wire ).
6.9.7 Overspeed alarm
6.8.7.1 Set up: Send SMS “ speed+123456+space+80 ” to the unit(suppose the speed is 80km/h),and it will reply “speed OK!”. When the target moves exceeding 80km/h.the unit will send SMS “speed+Geo-info” to the central number.
6.9.7.2 Cancel: Send SMS “ speed+123456+space+0 ” to deactivate the overspeed alarm.
Remark: It is recommended that the speed alarm is set at not less than
30km/h.For below that rate; it may cause the excursion of the GPS signal influenced by clouds etc.
6.9.8 ACC working alarm
6.9.8.1 This function is disabled as default. To active this functions, send
" ACC+123456+Space+1 " to tracker, it will reply "ACC,CONFIG OK". And tracker will send "ACC on+latitude & longitude" to central number when detect ignition action, that means the vehicle has been started.
6.9.8.2 Send " ACC+123456+Space+0 " to disabled this function, tracker will reply "ACC,CONFIG OK".
6.9.9 Vibration alarm
Send SMS “ vibrate+123456+space+0 ” to deactivate this function.
Send SMS “ vibrate+123456+space+1-15 ” to set up vibrate level from 1 to 15
13
(1 is strongest level, 15 is lowest level)
6.9.10 Set all alarm mode
Send SMS" KC +123456+space+0 " to tracker to close the function.
Send SMS" KC +123456+space+1 " to tracker to choose alarm by SMS.
Send SMS" KC +123456+space+2 " to tracker to choose alarm by calling.
6.10
Cut off the Oil and Power System
Send SMS command “ DY+123456 ” to the tracker device, it will reply “DY
CONFIG OK” to your cell phone from the tracker device, and stop your car oil pump or elec as well.
6.11
Resume the Oil and Power System
Send SMS command “
TY+123456
” to the unit, It will reply “TY,CONFIG
OK” and resume your car oil pump or elec as well.
6.12
Arm
6.10.1 Set up arm by SMS
6.10.1.1 Send SMS command “ DOOR+123456+1 ” to the tracker device in the vehicle. It will reply “DOOR,CONFIG OK” in both armed and disarmed state, and the SMS command will make the tracker device enter into armed state if the unit currently disarmed.
6.10.1.2 User must stop the engine, (that is ACC is lower voltage).Sending SMS
14
“DOOR+123456+1” when close the door and left. You will set up arm status fail if the engine is turned on (the ACC is high voltage).
6.10.2 Set up arm by remote controller (Option)
Press button on the remote controller for 0.5 seconds, the car enters into armed state and the siren will beep one time, no SMS reply.
6.13
Function of Remote Controller (Option)
Description Button Function
ARM
DISARM
SOS
Press
Press for one time for one time
Press for one time, tracker will send SOS alert to authorized phone numbers.
Deterrence/car
Press search for one time when it is in arm state, siren will beep 10 seconds, press disarm button to quit.
6.14
Disarm
6.12.1 Disarm by SMS
Send SMS command " DOOR+123456+space+0 " to the tracker device in the vehicle, It will reply “DOOR,CONFIG OK” in both armed and disarmed state,
15 and the SMS command will make the tracker device enter into disarmed state if the unit currently armed.
6.12.2 Disarm by remote control (Option)
Press button on the remote control, the car enters into disarm state, and the siren will alarm two times, no SMS reply.
6.15
Silent Mode
6.13.1 Set up silent mode by SMS
1) Send SMS “ silent+123456+space+1 ” to tracker device, it will reply “silent ok!”. It means tracker device enters into silent mode, siren won’t be sound after alarm is triggered, but tracker will send alarm SMS to authorized number.
2) Quit silent mode send disarm command “ silent+123456+space+0
” to disable the function.
6.16
Switch between GPRS and SMS Mode
Send SMS “ GPRS+123456+space+1 ” to tracker device to switch to GPRS mode; Send SMS “ GPRS+123456+space+0 ” to tracker device disable GPRS mode. Both will reply “GPRS,CONFIG OK”.
6.17
Check the Vehicle State
Send SMS command “ check+123456 ” to the tracker device in the vehicle, it will reply following SMS:
16 imei: unique IMEI number for register in tracking platform. apn: APN info. Of SIM card.
IP: server IP and Port number.
Cnum: central number for receive alarms.
GPS: 1 means GPS working, 0 means searching signal, -1 means GPS sleep for lower power consumption purpose.
GSM: 100 means GSM signal value normal.
ITV: moving time interval is default 10s, static time interval is 300s.
TZ: time zone is default GMT 0.
OS: overspeeding alarm, 0 means deactivate, 1 means activate.
GF: Geo-fence function.
Dr:1 means door open.
Vib: vibration level.
6.18
Device Resetting
6.16.1 SMS Reset
Send SMS “ reset+123456
” to tracker device to reset the GSM module and GPS module of the tracker device, it will reply “reset ok”.
6.19
IMEI Checking
6.17.1 Send SMS command " getimei+123456 " to the unit. E.g. Send SMS command "getimei123456" to the tracker device, an IMEI number in 15 digits will reply to your cell phone.
6.17.2 Send SMS command " setimei+123456+space+15 digits IMEI number " to the unit.
17
E.g. Send SMS command "setimei123456 123456789012345" to the tracker device, it will reply SMS “SETIMEI,CONFIG OK”.
6.20
Time Setting
6.18.1
Send SMS command “ timezone123456+space+time ” to the tracker unit,
If succeed, It will reply “time OK”
6.18.2
For example: Send SMS “timezone123456 8”, 8 is Chinese time zone, If your country time zone is minus, send SMS “time zone123456 -8”.
6.21
TCP/UDP switch
Send SMS to switch TCP to UDP, SMS Command:" UDP+123456+space+1 " switch to UDP mode.
Send SMS Command:" UDP+123456+space+0 " switch off UDP mode.
6.22
GPRS Setting
User must send SMS via cell phone to set up APN, IP and port before starting tracking by GPRS on tracking system.
6.22.1 Set APN
6.22.1.1 APN standards for Access Point Name and differs from country to country. For more information about your local APN, please inquire with your local GPRS network operator.
6.22.1.2 Send SMS “ APN+123456+space+local APN+space+APN
18 name+space+APN 123456 ” via a cell phone and if succeeded, the tracker will return the message “APN OK”.
6.22.1.3 E.g. Send SMS command “APN123456 CMNET”. If succeeded, it will reply SMS “APN OK”
Notes: CMNET is the APN of one of china GPRS Network Operator (China mobile), it has no APN name and 123456.
6.22.2 Set IP and Port
Send SMS: “ adminip+123456+space+IP Address+space+port number ”, If succeeded, it will reply “ADMINIP,CONFIG OK”. E.g. Send SMS:
“adminip123456 116.205.4.114 8169” to the tracker device, (116.205.4.114 is IP,
8169 is port).
6.23
Set up monitor central number
6.23.1 Setup: send command “ centernum+123456+space+number
” to tracker, it will reply “centernum ok”. After setup monitor center number, the messages of auto track by SMS will be set to this center number, if all alarms need to be sent to this number too, then this center number must be setup as authorized number.
6.23.2 Cancel: Send “ centernum+123456 ” to tracker, it will reply
“CENTERNUM,CONFIG OK”.
7.
Cautions
Please comply with the instructions to extend the unit life:
19
1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry.
2. Don’t use & store the unit in dusty places.
3. Don’t put the unit in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
6. Don’t paint the unit, this may cause some foreign materials left in between the parts.
7. Don’t disassemble or refit the unit.
8. Please read the user manual carefully before installation and operation, learn something more about the voltage range. Otherwise, it won’t work properly or destroy the product.
8
．
Faults & the Solutions
Faults Solution
Startup Fail
Please check out the power wiring in correct place.
Call Fail Check the GSM antenna connected.
Hang up Fail
Monitor Fail Check if the authorized number is setup
Location report in
Check out if the GPS external antenna well. digits of zeros.
20
