Aydin Displays CAMBRIDGE CFP47W1 User Manual

CAMBRIDGE

USERS MANUAL

CFP47W1 Large Screen Series

VESA Wall Mount

LCD Monitor User Guide

Document No. 150-CFP-470

Contents

Important Safety Instructions ………………………………………………... 3

Safety Precautions …………………………………………………………………...…… 3

Installation ………………....………………………………………………………….…… 3

Technical Help ……………………………….…………………………………………… 3

Cleaning Your Display ……………….…………………………………….……………… 3

Features………………………………………………………………….……........ 4

Package Contents ……….....…………………….……………………………... 4

Dimension ……………………………………………………………………………….… 6

Installation ……………………………………………………………………………….… 7

Power Input …………….…….………………………………………………………….… 7

Power Interface ………..…….………………………………………………………….… 7

Connection …………….…..……….……………………..…………………………….… 8

Single Source Input ………….……………………………………………….................. 8

Operating The Monitor …….…………….……………………………............... 9

The Side Controller Of The Monitor ……….....……………………..….…………….… 9

The Remote Controller (RCU) Instructions ……………..…………………………….… 9

Change The RCU Battery ………………..….………………………….……………..… 10

Display Mode ……..…………………..………… ……………….……………..… 11

OSD Menu Function ……..…………………..………………………….……………..… 12

OSD Operating ……………..……………..….………………………….……………..… 13

Default Setting …………………………………………………………….……... 16

Supported Timing ………..…………………………….………………….……... 17

Specification …………..……………….………................................................ 18

Troubleshooting …………………………………….……….…………………... 19

Compliance ……………………………..…………………….…………………... 19

Appendix ………………………………..…………………….…………………... 20

Appendix II …..…………………………..…………………….………………….. 21

※

Please read this user’s manual completely before operating this monitor.

Safety Precautions

To turn off the power of the monitor, press”O” on the main power switch at back cover.

The power standby/on indicator goes off and the set cannot to be turned on/ off by using the POWER button on the remote control. (To turn on/off the monitor by the remote control, press the main power switch again and light the power standby/on indicator.)

When turning off the monitor by pressing the POWER button on the remote control, the main power of the monitor is not turned off completely.

To disconnect the monitor completely from power supply, remove the power plug from the outlet.

Press”O”to turn off monitor completely

If the power cord or plug is damaged or becomes hot, turn off the main power switch of the monitor, make sure the power plug has cooled down and remove the power plug from the outlet.

Installation (when install the monitor, please follow the instruction on the manual )

Don't install in temperatures exceeding specifications.

If the monitor used in environments with temperatures exceeding specifications, it may cause the case or other parts be distorted, damaged, overheating or an electric shock.

Don't install in a high-humidity environment exceeding specifications.

This may cause overheating or an electric shock.

Technical Help

When having technical problems, please contact Aydin Displays customer service.

Cleaning Your Display

Cleaning the surface of the monitor.

When the surface of the monitor is polluted, please wipe the surface with the cotton or clean cloth lightly.

If pollution is not easy to clean out, can use the cloth with 50% of the alcohol .

Please notice carefully that not to let alcohol enter the monitor, it may cause electrical failures.

Features

High-resolution HD panel

This monitor supports 1920 x 1080 HDTV format and can display true 16.7M colors, you can enjoy extreme fine pictures.

MVA system less-reflection black TFT LCD panel

MVA system and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the windows, the monitor shows bright and clear image with little reflection. The viewing angles of the monitor are as wide as 170° both horizontally and vertically, enough to enjoy clear images at any view angle.

Offer varieties of connection

Video system Input:

There are 3 choices of connection

VIDEO RCA

S-VIDEO Mini Din 4 pin

COMPONENT Mini Din 8 pin

RGB Input:

There are 2 choices of connection

RGB ANALOG D-Sub 15pin

RGB DIGITAL DVI-ID 24pin

Signal delivery

RS-232C in D-sub 9pin (Option)

Other functions

Building the light sensor inside, the monitor will adjust the brightness according to the surrounding light intensity.

There are two brightness levels pre-set. Under the bright condition, it will adjust to the bright mode.

Under the dim condition, the monitor will adjust to dim mode automatically.

Signal source auto detection.

PIP/ PAP function. Please see the chapter “ Display mode ”

Zoom in/out function.

Package Contents

Unpacking

CFP47W1 is packed by the carton box. During transportation, in order to protect the monitor, CFP47W1 is packed by cushions to be safe protect and package.

Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet for your monitor first.

Set the LCD Monitor box in an upright position and open from the top of the box before removing the top cushions.

Step 1: Remove the white handle and cut the bundle

Step 2: Remove the top cushion and take the accessories box out.

Top cushion &

Accessories Box

The Monitor

Bottom cushion

Packing list

Q’ty Item Q’ty

1 set CFP47W1 1 pcs

Item

DVI-D 24 pin cable

1 pcs Power cord 1 pcs D-SUB 15pin cable

1 pcs User's manual 1 pcs S-VIDEO Mini Din 4 pin cable

1 pcs Remote controller 1 pcs Component Mini Din 8 pin cable

1 pcs RCA cable 1 pcs RS232C D-sub 9pin cable (Option)

Dimension (Front & Back)

Installation

Environmental state

Operating temperature ︰ 5℃ ~ 4 0℃ (Fahrenheit : 41 ℉ ~ 104 ℉ )

Humidity ︰ max. 85%

Power Input

Power Cord

AC Power cord

This power cord is used to connect the side controls of the LCD monitor and the wall outlet.

Connect the power cord into main power of the monitor, “

│

” is power on, “

○

” is power off.

Input: 100-240V~ 3A 50/60Hz

The side of control

Single Input Interface

│ is power on

○

is power off

Main power –Switch &

AC socket

Power Interface

Main interface- switch & AC socket. Please see the chapter “ Power input ”

The side controller of the monitor

The remote control (RCU)

Connection

Video (RCA ) input

S-Video input

Component Y Pb/Pr input

DVI (DVI-D) input

RGB (VGA) input

RS-232C input (option)

Single Source Input

Input Interface

NO.

1

2

Name

Video-IN input connecter

S-video input connecter

3 Y-Pb-Pr (Y-Cb-Cr) inputs

4

5

DVI input connecter

RGB input connecter

6 Power cord input

7 RS232C-IN input (option)

The Video Signals Input

You can select Video input form 3 connections below:

Video signals Connection type

Remarks

RCA

Mini Din 4 pin

Mini Din 8 pin

DVI-D 24 pin

D-Sub 15 pin

D-Sub 9 pin

Video

S-Video

RCA

4 pins

8 pins (Y Pb/Cb Pr/Cr)

Suitable signal is automatically selected.

Signal

NTSC/PAL

NTSC/PAL

NTSC/PAL

RGB inputting

You can select RGB input for 2 connections as below:

RGB signals

RGB Analog VGA

Connection type

15 pins

RGB Digital DVI-D DVI-D 24 pins

Command delivery

RS-232C (Option)

Connection type

9 pin

Signal

RGB Analog

RGB Digital

Function communication port

Operating The Monitor

The Side Controller Of The Monitor

No. Key

1

2

3

4

5

6

7

Power

ENTER

〈 / +

〉/ -

＾

﹀

MENU

Power Switch ; Power ON/OFF

Activate selection

Menu right / Value increasing

Menu left / Value decreasing

Menu down

Menu up

Description

Enter OSD menu / Exit menu or select

The Remote Control (RCU) Instructions

No. Key Description

1 7

1

2

POWER

Y

Power ON / OFF

Menu left

2 8 3 △ Menu up

3 9

5 AUTO automatically

4

5

10

11

6

8

PIP

Z

Picture in picture

Menu right

6 12

9

10

11

12

▽

EXIT

SOURCE

SWITCH

Menu down

Exit and one level up

Input source selection

PIP picture switch

λ

OSD Lock/Unlock Control

Use control push buttons at side

Lock: Press ( Z /+) and ( ▽ ) at the same time and OSD will be locked.

Unlock: Press ( Z /+) and ( ▽ ) at the same time again and OSD will be unlocked.

Use remote controller

Lock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence and OSD will be locked.

Unlock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence again and OSD will be unlocked.

Change The RCU Battery (RCU option)

(1) (2)

(3) i. Push down as picture (1) and pull the back cover. ii. Replace with the new batteries as picture (2), 1 piece Lithium battery(CR2032) make sure the polarity of batteries are correct. iii. Place back cover and slide it is as picture (3). iv. Used batteries need to follow the city rule to discard. v. Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid resulting metal rust or fatal damage to the remote control hand unit. vi. Battery used according to the instruction

.

CAUTION

Risk of explosion if batty is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Display Mode

Main Source mode

The main source mode will be changed in the sequence as follows: VGA/DVI/ Composite (AV) / S-Video/

Component (YPbPr) by remote control or press “ MENU ”->” T ” by the side controller of the monitor.

PIP(sub source) mode

Press “ PIP ” button on the remote control (turn on PIP function), and press” source ” to select PIP input source.

There is no PIP button on side controller of the monitor.

The sub-source changes as the main source changes. (Picture 1)

Sub source

Main source

<Picture 1>

“ ● ” is activity option, “-----“ is inactivity option.

Example:

When main source is Composite (AV signal), the sub-source can select to VGA or DVI.

When main source is VGA, the sub-source can select to composite, S-Video or component.

OSD (On Screen Display) Menu Function

Main Menu

Main /

Second

Input signal setting

DISPLAY

Sub-Menu

(base on IGP mode)

Brightness

Contrast

Hue

Saturation

Flash-Tone

Description Setting

Adjust the brightness of the screen

Adjust the contrast of the screen

Adjust the picture hue of the screen

Adjust the picture saturation of the screen

Adjust the picture tone of screen

0~100

0~100

-45~+45

0,100

Off/Weak/Soft/Strong

Black Level

Adjust the black level of screen

(IGP mode enable only)

0,100

POSITION

PIP

CONTROL

Zoom

Zoom Horizontal Pan

Zoom Vertical Pan

Vertical

Horizontal

PIP Mode

PIP Size

Vertical

Horizontal

Scaling

Auto Adjust

Magnify the picture of screen

Select the left/right picture to magnify

Select the upper/down picture to magnify

Adjust the V-position of the Zoom picture

Adjust the H-position of the Zoom picture

Adjust the PIP mode

Adjust the PIP size

Adjust the V-position of PIP

Adjust the H-position of PIP

Select the picture ratio.

Auto adjustment

In/Out

Left/Right

Down/Up

0~255

0~255

Off/Singe/PAP

Small/Med\/Large

0~100

0~100

1:1/Fill/Aspect/panor

Select

Phase

Adjust the screen phase

(IGP mode enable only)

0~255

IMAGE

Clock

MEPG NR

Noise Reduction

Adjust the screen clock

(IGP mode enable only)

No working.

Future option

(IGP mode disable)

Select the noise reduction mode

(IGP mode disable)

0~255

Off/Low/Med/High

Angle Filtering

Film mode Defect

Sharpness

Gamma correction

Select the angle filtering function

(IGP mode disable)

Select the film mode defect function

( IGP mode disable)

Adjust the sharpness of the screen

(IGP mode disable)

Select the Gamma setting

Off/ On

Off/ On

-15~ 29

COLOR

Audio setting

( option )

Color Temperature

Red

Green

Blue

Volume

Balance

Bass

Treble

Select the color temperature setting

Adjust red color

Adjust green color

Adjust blue color

Adjust the volume of the OSD menu

Adjust the balance of the OSD menu

Adjust the bass of the OSD menu

Adjust the treble of the OSD menu

Off/ 2.2/ 2.4

User/3200K/6500K,

7500K/9300K

0~255

0~255

0~255

0~100

-15~+15

-7 ~+7

-7 ~+7

OSD menu

Vertical

Horizontal

Blend

Time out

OSD Zoom

Language

Adjust the OSD menu V-position

Adjust the OSD menu H-position

Adjust the OSD menu of blend

Adjust the OSD menu display time

Magnify the OSD menu

0~255

0~255

0~15

0~60

On/Off

Language Language setting English

Default setting

RCU

Factory reset

Set display address

Light Sensor

Light sensor Value

Input signal selection

Reset to the factory default setting

Select monitor ID address(optional)

Select the light sensor setting

Adjust the light sensor value

Yes/ No

0~255

On/ Off

0~100

VGA

DVI

Composite

S-Video

Component

(IVP) means selection is working on Video mode.

(IGP) means selection is working on VGA mode.

OSD Operating

Structure of OSD Menus

λ

Main Menu

On side of controller:

Press “ MENU ” to enter Main Menu

Press“

＜/ ¬

” or “

＞

/

﹣

” to select Main Menu ex (Picture setting,

Language, Original Default Setting)

On RCU:

Press “ MENU ” to enter Main Menu

Press“ Z ” or “ Y ” to select Main Menu ex (Picture setting,

Language, Original Default Setting).

λ

Display Setting-

On side of controller:

1. Press “ MENU ” ->” ENTER ” to enter “ DISPLAY ” item.

2. Press ”

﹀

” to select sub-item(Brightness, contrast, Hue….),

3. Press“ ＜/ ¬

” or “ ＞ / ﹣ ” to adjust

4. Press “ ENTER ” to save the setting, when finished adjusting.

5. Press “ MENU ” to exit the item.

On RCU:

1. Press the “ MENU ” ->” ENTER ” to enter “ DISPLAY ” item.

2. Press ” ▽ ” to enter sub-item(Brightness, contrast, Hue….),

3. Press “ Z ” or “ Y ” to adjust

4. Press ” ENTER ” to save the setting, when finish adjusting.

5. Press “ EXIT ” to exit the item.

λ

Picture Setting

On side of controller:

1. Press “ MENU ” to enter Main Menu.

2. Press “

＞

/

﹣

“ 2 times to select picture setting.

3. Press “ Enter ” to enter item.

4. Press ”

﹀

” to select sub-item(Vertical, Horizontal, Blend...),

5. Press “ ＜/ ¬

” or “ ＞ / ﹣ ” to adjust

6. Press ” Enter ” to save the setting, when finish adjusting.

7. Press the “ MENU ” to exit the item.

On RCU:

1. Press the “ MENU ” ->” ENTER ” to enter picture setting

2. Press“ Z ” or “ Y ” to select Main Menu.

3. Press the “ ENTER “ to enter item.

4. Press ” ▽ ” to enter sub-item(Vertical, Horizontal, Blend…),

5. Press “ Z ” or “ Y ” to adjust

6. Press “ ENTER ” to save the setting, when finish adjusting.

7. Press” EXIT “ to exit the item

λ

Language Setting (English only)

On side of controller:

1. Press “ MENU ” to enter Main Menu.

2. Press “ ＞ / ﹣ ” 3 times and press the “ Enter ” to enter item.

3. Press ”

﹀

” to select sub-item(English only),

4. Press ” Enter ” to save the setting, when finish adjusting.

5. Press “ MENU ” to exit the item.

On RCU:

1. Press “ MENU ” ->” ENTER ” to enter picture setting

2. Press“ Z ” or “ Y ” to select Main Menu.

3. Press “ ENTER “ to enter item.

4. Press ” ▽ ” to enter sub-item(English only),

5. Press “ ENTER ” when finish adjusting.

6. Press” EXIT “ to exit the item

λ

Original Default Setting

On side of controller:

1. Press “ MENU ” to enter Main Menu.

2. Press “

＞

/

﹣

” 4 times to select original default setting.

3. Press “ Enter ” to enter item.

4. Press ” ﹀ ” to select sub-item(Factory Reset. Set display …),

5. Press “

＜/ ¬

” or “

＞

/

﹣

”to adjust

6. Press ” Enter ” to save the setting ,when finish adjusting.

7. Press “ MENU ” to exit the item.

On RCU:

1. Press “ MENU ” to enter Main Menu.

2. Press“ Z ” or “ Y ” to select Main Menu.

3. Press “ ENTER “ to enter item.

4. Press ” ▽ ” to enter sub-item(Factory Reset. Set display …),

5. Press “ Z ” or “ Y ” to adjust

6. Press “ ENTER ” to save the setting, when finish adjusting..

7. Press” EXIT “ to exit the item

λ

Input Signal Selection

On side of controller:

1. Press the “ MENU ” to enter Main Menu.

2. Press “

﹀

” to enter

3. Press “ ＜/ ¬

” or “ ＞ / ﹣ ” to select single input.

4. Press ” Enter ” when finish adjusting.

On RCU:

1. Press the “ MENU ” to enter Main Menu.

2. Press ” ▽ ” to enter

3. Press “ Z ” or “ Y ” to select single input.

4. Press “ Enter ” when finish adjusting.

Default Setting

Item Default

Power switch Off

Brightness 80

Contrast 50

Color temp. User

Red 255

Green 255

Blue 255

Language English

Auto Adjust On

Supported Timing

Video Mode fH

(kHz) fV

(Hz)

Sync polarity

Horizontal (dot) Vertical (line)

Dot clock

(MHz) H V A B C D E O P Q R S Analog

18

19

20

21

22

23

24

25

26

27

7

8

9

10

5

6

1

2

3

4

11

12

13

14

VESA

15 Macintosh

16

VGA 640x480

SVGA 800x600

31.469 59.940 25.175 N N 800 96 48 640 16 526 2 33 480 11 O O

37.861 72.809 31.500 N N 832 40 128 640 24 520 3 28 480 9 O O

37.500 75.000 31.500 N N 840 64 120 640 16 500 3 16 480 1 O O

35.156 56.250 36.000 P P 1024 72 128 800 24 625 2 22 600 1 O O

37.879 60.317 40.000 P P 1056 128 88 800 40 628 4 23 600 1 O O

48.077 72.188 50.000 P P 1040 120 64 800 56 666 6 23 600 37 O O

46.875 75.000 49.500 P P 1056 80 160 800 16 625 3 21 600 1 O O

48.363 60.004 65.000 N N 1344 136 160 1024 24 806 6 29 768 3 O O

56.476 70.069 75.000 N N 1328 136 144 1024 24 806 6 29 768 3 O O XGA 1024x768

60.023 75.029 78.750 P P 1312 96 176 1024 16 800 3 28 768 1 O O

1152x864 67.500 75.000 108.000

P P 1600 128 256 1152 64 900 3 32 864 1 O O

SXGA

1280x1024

63.981 60.020 P P 1688 112 248 1280 48 1066 3 38 1024 1 O O

79.976 75.025 P P 1688 144 248 1280 16 1066 3 38 1024 1 O O

832x624 49.725 74.500 57.283 N N 1152 64 224 832 32 667 3 39 624 1 O O

17 WXGA 1360x768

37.50 50.000 74.250 N N 1980 40 220 1280 440 750 5 20 720 5 O O

720p 1280x720 1280 750 5 20 720 5 O O

1280 750 5 20 720 5 O O

1920 562 2 5 540 15 O O

33.716 59.94 74.176 P P 2200 44 88 1920 148 562 3 19 540 O O O

33.716 59.94 74.176 P P 2200 44 88 1920 148 562 3 19 540 O O O

O

1920 1250 O

1920 1125

1080p 1920x1080

67.433 59.94 148.352

P P 2200 44 148 1920 88 1125 5 36 1080 4 O

O

O

O

O

Video Mode fH

(kHz) fV

(Hz)

Dot clock

(MHz)

1 480i NTSC

2 576i

3 480P 720X480 31.542 27.00

4 576P 720X576 31.25 28.812

O O O O

O O O O

O

O

Specification

Item Specification Unit

LCD panel

Graphic

Active Area

Driver Element

Pixel Number

Pixel Arrangement

Display Color

Trans-missive Mode

Viewing Angle (H / V)

Brightness

Contrast Ratio

Response Time

Separate Sync.

Horizontal Sync.

Vertical Sync.

Input Connector

Performance

Power supply

Physical

Function

Power consumption

Auto Adjust

Screen Scaling

Power Management

Gamma Correction

Color Adjustment

OSD Language

PIP

Zoom

Input AC

Operation Mode

Power Saving Mode

Dimension, (WxHxD)

Net Weight

Gross Weight

OSD key

Wall mount

1042.56(H) x 586.44(V) 47” diagonal a-si TFT active matrix

1920 x R.G.B. x 1080

RGB Vertical Stripe

16.7M

Normally Black

176 / 176

500 (typ.)

1000(typ.)

8 (Gray to Gray, typ.)

LVDS Level

Positive / Negative

Positive / Negative

D-Sub 15 pins, DVI-D 24 pins, Component

Composite, S-Video, RS-232C(option)

Clock, Phase, H Position & V Position

-

-

VGA/SVGA/XGA/SXGA/WXGA Full Screen Display -

VESA DPMS, DVI DMPM -

Off, 2.2, 2.4

User, 3200K, 5400K, 6500K & 9300K -

English -

-

-

-

4 size; small/ Middle/ Large/PAP

Zoom in / out

V (Worldwide)

≤

290 (max.)

≤

20(max)

W

W

1139.4x126.4x684.39 (w/o stand) mm

43.7

50.7

7

VESA standard 200x 200 ;200x 600 kg kg key mm

Mm

- pixel

- color

- degree cd/m2

- msec

Troubleshooting

Before calling Aydin Displays customer service, please check the following chart for a possible cause to the trouble you are experiencing.

Perform the adjustments according to page 10 “Operation The Monitor”

Refer to the following items if you can’t find a proper item listed in the Operating the Monitor or if the problem remains. if the problem you have experienced isn’t described below or you can’t correct the problem, stop using the monitor and call service personnel or your dealer.

No Display

Problem Check these things

Check the power plug insert on wall outlet..

Check the main power switch

If AC socked is OK, please check another set of equipment.

Display is not in the center.

Display is shaking.

The remote control doesn’t work

Check input single, the signal may not be suitable.

If the signal timing of the computer is within the spec.

If the signal timing of the computer is within the spec.

Make sure the battery is inserted matching the + and – marks of the battery compartment.

The battery may be exhausted..

Use the remote control aiming at the remote control sensor.

The picture color is pale, or not clear Check picture quality to adjust.

If you are using YUV terminals, make sure cables are correctly connected.

Compliance

FCC Compliance Statement:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CE

EN 55022 、 EN 61000-3-2 、 EN-61000-3-3

EN 55024 、 IEC61000-4

EN 60950 [Low-Voltage Directive (73/23/EEC)]

Appendix I

Moving Notice:

Moving the monitor requires at least two people. If not, it may drop and a serious injury may result.

Moving/shipping the monitor, please hold the white handles and be sure to make the bundle. If not, it may drop and a serious injury may result. Please see as below pictures.

Appendix II

Industrial VESA Wall Mount kit

Please follow all manual instructions and refer all servicing to qualified service personnel.

Moving the monitor requires at least two people. If not, it may drop and a serious injury may result.

Before installing, please check the installing manual in wall mount kit box.

Before installing, please make sure the wall is strong enough. Ex. A solid cement wall.