advertisement
P460,P450,
P442,P430,
P400
P430
P460
P450
P442
P400
P4TS
Compact Stand for the P4, Bravo
®
II, and Bravo Speakers
Required Tools: (not included)
• Flat head
Screwdriver
P4TS Included
Hardware:
Speaker screw (short) x 2
• Phillips head
Screwdriver
• Pliers*
*Required for Bravo II and Bravo only
Speaker Screw (long) x 2
M5 x 18 Threaded
Machine Screw x 3
Split Washer (small) x 3
2 3 ⁄
4
"
70mm
Split Washer (large) x 2
P4TS Included
Parts:
8 1 ⁄
4
"
210mm
P4TS Base x 1
6 1 ⁄
2
"
165mm
1 ⁄
4
"-20 Threaded Nut x 2
2 3 ⁄
4
"
70mm
4 7 ⁄
8
"
123mm
P4TS
Horizontal Post x 1
Rubber Feet x 6
Plug x 1
P4TS
Vertical Post x 1
14 7 ⁄
32
"
136mm
P4 Vertical Mount Assembly Instructions:
This configuration is compatible with Models: P460,
P450, P442, and P430.
Step One: Attach Base
Attach the base to the vertical post with the three included threaded machine screws and split washers (small) using a
Phillips head screwdriver. The post has already been threaded to ease screw installation. Attach rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route the speaker wire through the opening in bottom of the base, down through, and out the opening in the post. Use the top opening for the P430 and P442 and the bottom opening for the P450 and
P460. Leave several extra inches of speaker wire exposed to ease connection with the P4 speaker.
Step Three: Mounting the P4 Speaker
Due to the weight of the P4 speaker, it is recommended that the installation be performed with the P4 speaker laying face down with the grille removed on a soft surface such as a plush carpeted floor or the P4 shipping carton. Inspect the area where the speaker will lay making sure that there are no objects that could damage the speakers or scratch the front of the P4.
1.
Position the P4TS close to the P4 speaker as illustrated.
2.
Connect the speaker wire to the terminals on the P4 speaker.
3.
Mount the speaker to the post by lining up the two threaded inserts in the back of the P4 speaker with the two outside machined holes (middle hole is not used) in the post. Insert the two speaker screws (short) and tighten. Insert the plug into the unused machined hole on the post.
Note: Do not over-tighten the screws.
4.
Take up any slack in the speaker wire by gently pulling the wire at the opening in the base.
Required Tools:
•Flat head
Screwdriver
•Phillips head
Screwdriver
Hardware / Parts:
Speaker
Screw
(short) x 2
Threaded
Machine
Screw x 3
Split Washer
(small) x 3
P4TS
Base x 1
P4TS
Vertical
Post x 1
Plug x 1
P4 Horizontal Mount Assembly Instructions:
This configuration is compatible with Models: P460,
P450, P442, P430, and P400.
Step One: Attach Base
Attach the base to the horizontal post with the three included threaded machine screws and split washers (small) using a
Phillips head screwdriver. The post has already been threaded to ease screw installation. Attach rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route the speaker wire through the opening in bottom of the base, down through, and out the opening near the top of the post. Leave several extra inches of speaker wire exposed to ease connection with the P4 speaker.
Step Three: Mounting the P4 to the Stand
1. Using the speaker screws (long) and speaker screws
(short), mount the P4 wall bracket to the P4TS post.
The wall bracket is threaded to accept the speaker screws. Use the speaker screws (long) on the upper two threaded inserts and the speaker screws (short) on the lower two threaded inserts.
2.
Mount the retaining screws (included with P4 speaker) and connect the speaker wire to the terminals on the back of the P4 Speaker.
3.
Slide the speaker into the retaining channels. The speaker is held in place by gravity.
Note: For detailed instructions on installing the speaker to the wall bracket, please refer to the P4 owners manual.
4.
Take up any slack in the speaker wire by gently pulling the wire at the opening in the base.
Required Tools:
•Flat head
Screwdriver
•Phillips head
Screwdriver
Hardware / Parts:
Speaker
Screw
(short) x 2
Speaker
Screw
(long) x 2
Threaded
Machine
Screw x 3
Split Washer
(small) x 3
P4TS
Base x 1
P4TS
Horizontal
Post x 1
Bravo Vertical Mount Assembly Instructions:
This configuration is compatible with Models: Bravo II and Bravo.
Step One: Attach Base
Attach the base to the vertical post with the three included threaded machine screws and split washers (small) using a
Phillips head screwdriver. The post has already been threaded to ease screw installation. Attach rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route the speaker wire through the opening in bottom of the base, down through, and out the slot in the opening near the top of the post. Leave several extra inches of speaker wire exposed to ease connection with the Bravo speaker.
Step Three: Mounting the Bravo Speaker
1.
Using the speaker screws (long), washer, and 1 ⁄
4
"-20 threaded nut, mount the
Bravo mounting bracket to the P4TS post.
2.
Remove the speaker’s grille by grasping the back of the cabinet in one hand, while gently pulling the grille away with the other hand.
3.
Connect the speaker wire to the terminals on the Bravo speaker.
4.
Align the openings in the back of the speaker with the two posts protruding from the bracket as shown and attach the speaker to the bracket by inserting the supplied screws through the holes in the front of the speaker and into the bracket as shown. Insert the plug into the unused machined hole on the post.
Note: For detailed instructions on installing the speaker to the wall bracket, please refer to the Bravo owners manual.
4.
Take up any slack in the speaker wire by gently pulling the wire at the opening in the base.
Required Tools:
•Flat head
Screwdriver
•Phillips head
Screwdriver
•Pliers
Hardware / Parts:
Speaker
Screw
(long) x 2
Threaded
Machine
Screw x 3
Plug x 1
P4TS
Base x 1
Split
Washer
(small) x 3
P4TS
Vertical
Post x 1
Split
Washer
(large) x 2
1 ⁄
4
"-20
Threaded
Nut x 2
If Service Seems Necessary
First, contact the dealer from whom you purchased the speakers. If that is not possible, write to:
Boston Acoustics, Inc.
Attn: Parts and Service
300 Jubilee Drive
Peabody, MA 01960 U.S.A.
Or contact us via e-mail at: [email protected]
We will promptly advise you of what action to take. If it is necessary to return your P4TS compact stand to the factory, please ship it prepaid. After it has been repaired, we will return it freight prepaid in the U.S.A. and Canada.
300 Jubilee Drive
Peabody, MA 01960
U.S.A.
978.538.5000
www.bostonacoustics.com
Boston, Boston Acoustics, Bravo, and the Boston Acoustics logo are registered trademarks of Boston Acoustics, Inc.
Specifications are subject to change without notice.
© 2004 Boston Acoustics, Inc.
042-002139-1
advertisement
Related manuals
advertisement