Quick Start Guide

CamFi Pro

Packaging List

1. CamFi Pro

2. 3200 mAH battery

3. Mini USB cable for connecting to the camera

4. Micro USB cable for charging the battery

5. Quick start guide

CamFi Pro Overview

Power

Battery

Wi-Fi

USB

USB port

ON/OFF

Charging port

Reset

Power Light

Turned on when the system is starting up

Battery Light

The light is on when the battery is low.

Wi-Fi Light

The WiFi starts up normally, when the light is on.

USB Light

Turned on when the USB is connecting.

Hot shoe screw

Battery compartment

Charging Battery

Use the micro USB cable to connect to a mobile phone charger or the USB port of a computer to charge the battery of the CamFi device.

USB

Micro USB

Connect to CamFi Pro

CamFi Limited

Quick Installation

1. Connect CamFi Pro to your camera

Connect the CamFi Pro device to your camera using the mini USB cable, then turn on the CamFi

Pro and your camera.

Get the CamFi app

You will need to install the CamFi app on your smartphone or your PC. The CamFi app is available for iPhone®, Android ™ , Mac and Windows®. For a full list of supported devices, visit: http://www.cam-fi.com/download.html

1. On your smartphone or your computer browser, visit: http://www.cam-fi.com/download.html

2. Follow the instructions to install the CamFi app on your smartphone or your computer.

Connect to the Wi-Fi hotspot of the CamFi Pro

After you turn on CamFi Pro and the system status indicator light turns a constant green, you can find and connect to the Wi-Fi hotspot of the CamFi

Pro with the name prefixed with “CamFi-Pro”on your smart phone or your computer.

CamFi-Pro-xxxxxx

Start CamFi App

Launch the CamFi app on your smart phone or your computer.

Firmware Upgrade

The CamFi app will automatically check if there is a new version of firmware available for the CamFi

Pro. When there is a new version available, the app will start the upgrade wizard to upgrade the firmware of the CamFi Pro. You can follow the instructions provided by the wizard to upgrade the firmware.

Need Further Assistance?

For answers to common questions and troubleshooting steps, please visit: http://www.cam-fi.com/support.html

You can also contact us with the following contact information:

E-mail: [email protected]

Address: A1002, Tsinghua Science Park, 1st

College Road, Zhuhai, Guangdong, China

Website: http://www.cam-fi.com

FCC Warning:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures: o Reorient or relocate the receiving antenna.

o Increase the separation between the equipment and receiver.

o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

o Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not

explicitly approved by manufacturer could void your

authority to operate this equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure

limits set forth for an uncontrolled environment. This

device and its antenna must not be located or operating in conjunction with any other antenna or

transmitter.