advertisement
Steampunk Bay ™
CF-8502 & CF-8602
Widespread Lavatory Faucet
Installation Instructions
CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED
BY A LICENSED PROFESSIONAL
IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer.
Operating Specifications:
Recommended Supply Pressure: 20 to 70 psi *†
Maximum Flow Rate: 1.2 gpm
*
Operating pressures between hot and cold supplies should vary no more than 30 psi.
†
If water pressure exceeds 70 psi, install a Pressure-Reducing Valve (PRV).
1 INSTALLING SPOUT TO SINK/DECK
1
Tighten spout BASE (4) and DECORATIVE NUT
(2) onto spout RISER (3) , and slide onto spout
SHANK (1a)
1a
2
Insert spout SHANK (1a) though sink/deck hole
3
NOTE: Sink/Deck recommended hole size shall be Ø 1-3/8”
4
From underside, place SLOTTED WASHER (5) onto spout SHANK (1a) and tighten SPOUT (1) into place with NUT (6)
Insert RUBBER WASHER (7) into TEE (8) and attach to spout SHANK (1a)
IMPORTANT: TEE (8) should be tightened to create watertight seal and positioned to allow ease of attachment of valve hoses
CF-8502_ii_190102
1a
6
5
7
8
Pg 1
2 INSTALLING VALVE
From underneath insert VALVE (12) though appropriate sink/deck hole
IMPORTANT: VALVES (12) are labeled as follows:
BLUE is COLD left turning (counter-clockwise) closed
RED is HOT right-turning (clockwise) closed
Position flange NUT (10) , WASHER (9) , and
SPACER (11) so that VALVE (12) extends 1-1/2” above sink/deck surface
Attach INVERTED NUT (13) to VALVE (12)
Use HANDLE (15) to confirm proper VALVE (12) alignment, rotate VALVE (12) if necessary
NOTE: See image in Section 4 to confirm proper alignment of other handles
3 INSTALLING ESCUTCHEON
NOTE: Confirm orientation of RISER (14c) ; hash marks at bottom as shown
Insert O-RING (14f) into handle BASE (14e) , place
COINED RING (14d) on handle BASE (14e) , position handle RISER (14c) on COINED RING
(14d) , fit WASHER (14b) to ESCUTCHEON
(14a) , place ESCUTCHEON (14a) onto RISER
(14c)
Place ESCUTCHEON ASSEMBLY (14) onto VALVE
(12) and secure to sink/deck surface by tightening
ESCUTCHEON (14a)
Use a ruler or straight edge to align the spout base, and handle bases of the faucet as shown
After alignment retighten ESCUTCHEON (14a) and spout NUT (6)
NOTE: Return to Section 2 if valve is not aligned properly
CF-8502_ii_190102
15
12
11
10
1-1/2"
13
9
12
14d
14e
14f
14a
14b
14c
12
Pg 2
4
INSTALLING HANDLE
Slide HANDLE (15) down onto and engage valve
STEM (12a)
Tighten handle NUT (15b)
5 INSTALLING VALVE HOSES
Attach small hose NUT (16a) to spout TEE (8a)
Attach large hose NUT (16b) to valve side
OUTLET (12b)
Repeat on other side valve
CF-8502_ii_190102
15b
15b
15b
16a
16b
8a 12b
Pg 3
15
15
15
12a
6
INSTALLING DRAIN
Slide white foam WASHER (17) up under flange of
BODY (18)
- or -
Apply thin film of Silicon ® sealant (or equivalent –
DO NOT use petroleum-based sealant as this WILL void finish warranty) to underside of flange on
BODY (18)
Insert BODY (18) down through sink drain hole
From underside, slide MACH-WASHER (19) and
FRICTION-WASHER (19a) up onto BODY (18)
Secure BODY (18) into place with flange NUT
(20)
Apply Teflon ® tape (22) (not supplied) to threaded portion of TAILPIECE (21) & tighten onto BODY
(18)
7 INSTALLING SUPPLY LINES
IMPORTANT: Prior to attachment, flush supply lines to remove debris that may cause damage or malfunction to valve cartridge.
The following are two types of supply lines (not included) that may be installed to the valve bodies:
Ballnose riser for exposed application
Install BALLNOSE RISER (23a) using valve NUT
(12c) to secure riser to valve INLET (12b)
Flexible riser for non-exposed application
Discard valve NUT (12c) & install FLEX RISER
(23b) to valve INLET (12b)
Final connections
Attach drain tailpiece to p-trap (not supplied)
Turn on water supply valves & check for leaks
CF-8502_ii_190102
19
19a
20
22
21
17
18
12c
12b
23a
23b
californiafaucets.com 5271 Argosy Ave. Huntington Beach, CA 92649 800-822-8855 Pg 4
advertisement
Related manuals
advertisement