SICOM3024 Industrial Ethernet Switch User`s Manual

SICOM3024 Industrial Ethernet Switch User Manual

SICOM3024 Industrial Ethernet Switch

User’s Manual

KYLAND Telecom Technology Co., Ltd.


SICOM3024 Industrial Ethernet Switch

User’s Manual

Copyright © 2006 KYLAND Telecom Technology CO., LTD.

All rights reserved.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of KYLAND

Corporation.

Publisher：KYLAND Telecom Technology CO., LTD.

Address：P.O. Box 100096, 085, Beijing, China

Website：http://www.kyland.cn postcode：100096

Tel：（+8610）82900771

FAX：（+8610）82900780

E-mail：[email protected]

Version：V1, Jan. 2007

No.：s3a01070101


Preface

SICOM3024 is a high-performance network-managed industrial Ethernet switch specially designed by KYLAND Telecom Technology CO., LTD. for industrial applications. Its high-performance switch engine, solid and closed case design, high-efficient single-rib shape case heat dispersion surface without fans, overcurrent, overvoltage and EMC protection at power input side, and excellent EMC protection of

RJ45 port allows SICOM3024 applicable in harsh and dangerous industrial environments. The redundant function of optical fiber network, independent entire network management channel, redundant power input function, and powerful entire network real-time management system provides multiplex guarantee for reliable operation of the system.

The user’s Manual for SICOM3024 Industrial Ethernet Switch mainly introduces the information on technical principles, performance indexes, installation and commissioning, network management etc. to provide users with references in startup, expansion and routine maintenance. It is a practical teaching material that can be used for knowledge and understanding of SICOM3024 industrial Ethernet Switch.

This manual mainly includes the following contents:

Chapter 1 Overview and system features of SICOM3024 industrial Ethernet switch;

Chapter 2 Performance and service functions of SIOCM3024 industrial Ethernet switch;

Chapter 3 Hardware structure of SICOM3024 industrial Ethernet switch;

Chapter 4 Installation of SICOM3024 industrial Ethernet switch;

Chapter 5 Field test methods for SICOM3024 industrial Ethernet switch;

Chapter 6 Networking modes and system configuration of SICOM3024.

Chapter 7 WEB management of SICOM3024 industrial Ethernet switch;

Chapter 8 CLI of SICOM3024 industrial Ethernet switch;

Appendix A Introduces twisted pair and pin distribution rules of SICOM3024 industrial

Ethernet switch;

Appendix B Introduces cable types and specifications of SICOM3024 industrial


Ethernet switch;

Appendix C Introduces abbreviations used in this manual.

Appendix D FTP application of software upgrade

Statement: as product and technology upgrades and improves constantly, the contents of this document may not completely accord with the actual product. For product upgrading information, please visit our company’s website or directly contact with our business representative.


Notice for Safety Operation

This product offers reliable performances as long as it is used within the designed scope. Artificial damage or destruction of the equipment should be avoided. z Carefully read this manual and well preserve this manual for future reference; z Do not place the equipments near water sources or damp places; z Do not place anything on power cable which should be placed in unreachable places; z Do not tie or wrap the cable to prevent fire. z Power connectors and connectors for other equipments should be firmly interconnected and frequently checked.

In the following cases, please immediately disconnect the power supply and contact with our company:

1. Water gets into the equipments;

2. Equipment damage or shell breakage;

3. Abnormal operation conditions of equipment or the demonstrated performances have changed;

4. The equipment emits odor, smoke or noise. z Please keep optical fiber plugs and sockets clean. During operation of equipments, do not stare directly into the cross section of optical fiber; z Please keep the equipment clean; if necessary, wipe the equipment with soft cotton cloth; z Do not repair the equipment by yourself, unless it is clearly specified in the manual.


Explanation of Warning Marks:

This manual uses two kinds of noticeable warning signs to arouse special attention of users during operation. The implications of these signs are as follows:

Warning: pay special attention to the notes behind the mark, improper operation will result in serious damage of the switch or injury of operation personnel.

Caution, attention, warning, danger: remind the positions requiring attention during operation.


Contents

Chapter 1 System Overview ......................................................................................................................... 1

1.1 Product Overview ................................................................................................................................ 1

1.2 System Features................................................................................................................................... 1

1.3 Packing list and unpacking check........................................................................................................ 2

第二章 Performance Specifications ............................................................................................................ 5

2.1 System Specifications.......................................................................................................................... 5

2.2 Service Interface .................................................................................................................................. 5

2.3 Service Function .................................................................................................................................. 7

第三章 Hardware Structure ........................................................................................................................ 9

System Structure...................................................................................................................................... 9

3.1 .............................................................................................................................................................. 9

3.1.1 Case ........................................................................................................................................... 9

3.1.2 Front Panel............................................................................................................................... 10

3.2 Interface Description ......................................................................................................................... 11

3.2.1 Gigabit Optical Fiber interface ................................................................................................ 11

3.2.2 Optical Fiber interface ............................................................................................................. 12

3.2.3 RJ45 interface .......................................................................................................................... 13

第四章 Hardware installation ................................................................................................................... 17

4.1 Installation requirement ..................................................................................................................... 17

4.2 Mainframe installation....................................................................................................................... 17

4.2.1 Stable rack mounting ............................................................................................................... 17

4.3 Cable connecting ............................................................................................................................... 18

4.4 Optical Fiber Connection................................................................................................................... 18

4.5 Cable wiring ...................................................................................................................................... 19

第五章 Test methods .................................................................................................................................. 21

5.1 Self inspection ................................................................................................................................... 21

5.2 TP Port Test........................................................................................................................................ 21

-i-


5.3 Fiber Port Test ....................................................................................................................................21

第六章 Networking ways............................................................................................................................23

6.1 Network ways.....................................................................................................................................23

6.2 System configure................................................................................................................................23

第七章 WEB Management Software ........................................................................................................25

7.1 Login Web service..............................................................................................................................25

7.2 Equipment State Display ....................................................................................................................26

7.2.1 Basic information .....................................................................................................................26

7.2.2 Port State ..................................................................................................................................26

7.2.3 Port Flow..................................................................................................................................27

7.3 Equipment basic configuration...........................................................................................................27

7.3.1 IP address configure .................................................................................................................28

7.3.2 Equipment name configure ......................................................................................................28

7.3.3 Port configure...........................................................................................................................28

7.3.4 Password change ......................................................................................................................29

7.3.5 Software edition inquiry...........................................................................................................30

7.3.6 Software update........................................................................................................................30

7.4 Advanced Configuration ....................................................................................................................31

7.4.1 Port Traffic Control ..................................................................................................................31

7.4.2 VLAN Configuration ...............................................................................................................31

7.4.3 Port Mirroring Configuration ...................................................................................................32

7.4.4 Port Aggregation Configuration ...............................................................................................33

7.4.5 Redundant Ring Configuration ................................................................................................34

7.4.6 Port Priority Setting..................................................................................................................35

7.4.7 Other Configuration .................................................................................................................36

7.4.8 SNMP Configuration................................................................................................................37

7.4.9 IGMP-SNOOPING ..................................................................................................................37

7.4.10 ACL list control ......................................................................................................................38

7.5 Device Management...........................................................................................................................38

第八章 CLI Command ...............................................................................................................................41

-ii-

8.1Connect to the Switch and Login........................................................................................................ 41

8. 1.1 Command Line ....................................................................................................................... 41

8.1.2 Command syntax ..................................................................................................................... 41

8.1.3 Syntax help .............................................................................................................................. 42

8.1.4 Use syntax help to fill the command ....................................................................................... 42

8.1.5 Symbols in the command......................................................................................................... 44

8.1.6 Types of Command.................................................................................................................. 44

8.1.7 Command abbreviation............................................................................................................ 45

8.1.8 History commands ................................................................................................................... 46

8.1.9 Frequently used commands ..................................................................................................... 46

8.2 Common management methods ........................................................................................................ 53

8.3 Using Console port to manage switch ............................................................................................... 53

8.4 Configure Port ................................................................................................................................... 54

8.4.1 Enabled/Disabled Port ............................................................................................................. 54

8.4.2 Configure Port Rate, Duplex Mode and Flow Control ............................................................ 54

8.4.3 View Port................................................................................................................................. 55

8.4.4 View/Delete Port Statistics ...................................................................................................... 55

8.5 TRUNK ............................................................................................................................................. 56

8.6 Port Mirroring.................................................................................................................................... 57

8.7 Port Prioritization .............................................................................................................................. 57

8.8 VLAN ................................................................................................................................................ 57

8.8.1 VLAN Overview ..................................................................................................................... 57

8.8.2 Default VLAN ......................................................................................................................... 58

8.8.3 Create VLAN........................................................................................................................... 58

8.8.4 Change VLAN Name .............................................................................................................. 58

8.8.5 Add/Delete VLAN Port ........................................................................................................... 59

8.8.5 Show VLAN ............................................................................................................................ 59

8.9 IGMP Snooping................................................................................................................................. 60

8.9.1 IGMP Snooping overview ....................................................................................................... 60

8.9.2 Configure IGMP Snooping...................................................................................................... 60

8.10 DT-Ring........................................................................................................................................... 61

-iii-


8.10.1DT-Ring Overview ..................................................................................................................61

8.10.2 Create/Delete DT-Ring Domain .............................................................................................62

8.10.3 Add/Delete Ring-port .............................................................................................................62

8.10.4 DT-Ring Domain protocol enable/disable..............................................................................63

8.10.5 Display DT-Ring Domain State..............................................................................................63

Appendix A Twisted-pair and Pin Distribution.........................................................................................65

Appendix B Cable Type and Specifications...............................................................................................67

Appendix C Glossary...................................................................................................................................69

Appendix D FTP Application of Switch Software Update .......................................................................69

-iv-


Chapter 1 System Overview

1.1 Product Overview

SICOM3024 is a high-performance network-managed industrial Ethernet switch specially designed by KYLAND Telecom Technology CO., LTD. for industrial applications. Its high-performance switch engine, solid and closed case design, high-efficient single-rib shape case heat dispersion surface without fans, over-current, over-voltage and EMC protection at power input side, and excellent EMC protection of

RJ45 port allows SICOM3024 applicable in harsh and dangerous industrial environments. The redundant function of optical fiber network, independent entire network management channel, redundant power input function, and powerful entire network real-time management system provides multiplex guarantee for reliable operation of the system.

SICOM3024 series gigabit industrial Ethernet switch offers strong web-management which support CLI, Telnet, WEB, SNMP and OPC-based network management.

SICOM3024 supports 19 inch stable rack mounting for installation. There are two or four 1000M SFP interface in back panel. It offers twenty-four 10Base-T/100Base-TX , or sixteen 10Base-T/100Base-TX and (0-8) pair single(multi) 100Base-FX fiber port.

The fiber-ports can consist 1000Mbit redundant network and recovery time < 300ms.

The 100M fiber ports can consist 100Mbit redundant network and recovery time <

300ms. The six TP 10Base-T/100Base-TX ports 10/100M, full/half duplex,

MDI/MDI-X adaptive.

1.2 System Features

1.

High performance industrial Ethernet switch

Plug and play for 1000M SFP, changeable

-1-


2(4)G+8F fiber port provide various network for customers

Support various management software, easy entrance for user such as: CLI,

TELNET, SNMP, OPC.

10Base-T/100Base-TX self-adoptive Ethernet connector (full/half duplex),

MDI/MDI-X adoptive

100Base-FX full/half duplex SM/MM redundant connector

Recovery time < 50ms increase the system reliability

Setting and query for alarm of power and ports link.　

Broadcast storm control

IEEE802.3/802.U/802.3X store and forward

VLAN Tag

FTP online update, easy for equipment management and renew

2. Industrial Power Design

Provide industrial power input: DC24V、DC-48V、AC220V、DC110/220V

Power input over-current, over-voltage protection and EMC

3. Rugged design

Ribbed heat-removal design (fanless); operation at -35℃ to +75℃

Solid and closed case design, IP40, can be used in harsh environment

1.3 Packing list and unpacking check

１. Packing list

The packing case includes the following items:

SICOM3024 1 unit

User’s Manual for SICOM3024 Industrial Ethernet Switch 1 copy

Customer Service Guideline 1 copy

Ф4 grounding cold pressed terminal, M3×8 grounding screw 1 piece each

-2-

Chapter One System Overview

２. Unpacking check

Before opening the case, place it stably, pay attention to the direction of the packing case, and ensure its right side is facing upward, so as to prevent SICOM3024 from falling apart after opening the case. If a hard object is used to unclench the case, do not overly extend the hard object into the case to avoid damage of the equipments inside the case.

After opening the case, check the amount of SICOM3024 equipments (including main unit of SICOM3024, parts of equipment, user’s manual, customer service guideline) according to the packing list, and check the appearance quality of

SICOM3024.

Warning:

For the built-in precise parts of equipments, please handle with care and avoid strenuous vibration to avoid affecting the performances of equipments.

-3-


第二章 Performance Specifications

2.1 System Specifications

The system performance specifications of SICOM3024 industrial Ethernet switch are shown in Table 2-1.

Table 2-1 System Specs

Specs Description

Quantity of RJ45 port 24~16

×10Base-T/100Base-TX redundant port

Quantity of 100M redundant port

0-8 个 100Base-FX-SM/MM

System performance

Ethernet port

Fiber port

CONSOLE interface

Power supply

Standard: IEEE802.3、IEEE 802.3x、IEEE 802.3u

Store-and-Forward speed: 1488100 bps

Max. filtering speed: 1488100 bps

Switching mode: Store-and-Forward

Switching bandwidth of system: 32G

Electromagnetic compatibility interference: EN55022

Electromagnetic compatibility immunity: EN50082-2

Physical port: shielded RJ-45

RJ-45 port: 10Base-T/100Base-TX, supporting automatic negotiation function

Port standard: in line with IEEE802.3 standard

Transmission distance: <100m

Optical power: >-13dbm(SM) >-20dbm(MM)

Receiving sensitivity: <-28dbm(SM) <-35dbm(MM)

Wave length: 1310nm(SM) 1550nm(SM) 1310 nm(MM)

Transmission distance: 20～80Km(SM) <2Km(MM)

Connector type: LC, SC/FC

Transmission rate: 1.2Gbps, 125Mbps

Physical interface: shielded RJ-45

Interface standard: in line with RS232 standard (3 lines)

Interface rate: 9600bps

Input voltage: AC 220V（AC 200V～240V，50Hz～60Hz）

DC24V（DC 18V～36V）

DC-48V (DC -36V～-72V)

DC110V

-5-


Mechanical parameter

Ambient conditions

DC220V

Input power consumption: 14~22W

Over-current Protection: build-in

Physical dimensions (height

×width×depth): 44 ㎜×482.6 ㎜

×245 ㎜

Mounting mode: 19’ Stable rack mounting

Heat removal method: Ribbed aluminum casing heat dissipation without fan.

Outlet type: back outlet for service,

Shell protection: IP40

Weight: 4 ㎏

Operating temperature: -35℃～75℃

Storage temperature: -45℃～85℃

Humidity: 10%～95% （non-condensing）

2.2 Service Interface

1． 16/24-port 10Base-T/100Base-TX RJ45，Each RJ45 port has self adaptation function, capable of automatically configuring to 10Base-T or 100Base-TX state and automatically working in full duplex or half duplex operation mode. The transmission distance is 100m max.

2． Redundant 100Base-FX single mode or multi-mode optical fiber interfaces. The maximum throughput of each pair of optical fiber interface is 100Mbps, and it is forced to work in 100M full duplex mode. They support optical fiber line redundancy technology, with the recovery time less than 50ms.

3． 2/4 pairs of uplink redundant 100Base-FX single mode or multi-mode optical fiber interfaces. The maximum throughput of each pair of optical fiber interface is

100Mbps, and it is forced to work in 100M full duplex mode. They support optical fiber line redundancy technology, with the recovery time less than 50ms.

4. Conform to IEEE802.3/802.3U/802.3X /802.3Z/ab

5. Meanings of RJ45 port indicator: yellow lamp – rate indicator; on:100M, off:

10M; RJ45 Green lamp – connection state indicator, on: effective connection of network; blink: network active; off: no connection.

-6-

Chapter Three Hardware Structure

2.3 Service Function

The service function for SICOM3024 mainly include:

LED Indicator

The LEDs (front panel) indicate the port status correctly including transmission rate, link status and system status.

Layer-2 Switching

Switches work in two ways: Cut-Through and Store-and-Forward. In Cut-Through, a data packet is immediately relayed further after detecting the target address; in

Store-and-Forward, a data packet is first read-in completely and checked for errors before the switch relays the same. SICOM3024 employs Store-and-Forward that is a switching mode widely used.

VLAN

VLAN will divide one network into multiple logical subnets. Data packets cannot be transmitted between different VLANs so as to control the broadcast domain and segment flow and improve the reliability, security and manageability. SICOM3024 series supports IEEE802.1q VLAN tag. It can be divided into up to 4094 VLANs based on ports. The VLAN division can be realized via WEB, CLI, Kyvision3.0 software.

QoS Priority

IEEE 802.1p is the most popular priority solution in the LAN environment. SICOM3024 series supports 802.1p standard, by which you can configure the port-based priority when the terminal does not support 802.1p and different priority for the ports is wanted.

Port Trunking

In SICOM3024, multiple physical ports can be aggregated into one logic port, which has the same rate, duplex and VLAN ID. Port Trunking can be configured in one single switch for max 7 ports. In this way, the pressure of network traffic is reduced.

Port Mirroring

The data of one port can be mapped to another port for user to real-time monitor the communication.

Configure Port Working Modes

SICOM3024 is able to configure the working mode of all ports through management: full/half duplex adaptive, enforced full/half duplex, 10M/100M adaptive, enforced 100M full-duplex for 10M/100M fiber ports, enforced 1000M full-duplex for 1000M fiber/TP

-7-

-8-


ports.

Configure Port Traffic Flow

You can configure the TX and RX rate of all ports via the management software of

SICOM3024. For port of 100Mbps, it can be set as 128K、256K、512K、1M、2M、

10M、50M、100M. For Gigabit port, it can be set as 100M、500M、1000M.

IGMP

IGMP is Internet Group Multicast Protocol. SICOM3024 series offers IGMP monitor and query functions. Data packets can be transmitted to multiple necessary host computers to prevent overloading. This solves the problems of occupied bandwidth when broadcasting.

Broadcasting Storm Control

SICOM3024 series offers broadcast storm protection ensuring the smooth communication platform of the switch network. The switch will filter out the over flow once the bandwidth of broadcast flow exceed the limit.

DT-Ring

Each Ethernet port or fiber port of SICOM3024 series is able to configure as redundant mode or not. It makes you form different Gigabit or 100M redundant ring easily and flexibly. The recovery time is less than 50ms.


第三章 Hardware Structure

3.1 System Structure

3.1.1 Case

SICOM3024 case is 19’ stable rack mounting type structure. The entire unit has a six-side-enclosed structure, with protection class up to IP40. The case’s left and right side plates made of ribbed aluminum profile are a part of the heat dispersion system of the entire unit. The single-rib structure can double heat dissipation area. The heat generated when the unit is working is effectively dissipated into the environment via the ribbed heat-dissipation surface in the form of radiation and convection greatly increasing the high temperature resistance of equipment. Discarding the traditional form of axial fan heat dispersion reduces power consumption of the entire unit and increases the stability of the system. The figuration of SICOM3024 case is shown in

Figure 3-1.

Its contour dimension is44 ㎜×482.6 ㎜×245 ㎜（height×width×thickness） a.SICOM3024-2GX-24T

b.SICOM3024-2GX-8S（M）-16T

-9-


Figure 3-1 outline drawing of SICOM3024

Warning:

The shell of this switch is a part of the heat dissipation system of the unit. It may get hot during working, so never touch the shell when the equipment is working to avoid burning.

3.1.2 Front Panel

SICOM3024 Industrial Ethernet switch front panel is show as Figure 3-3： a.SICOM3024-4GX front panel b.SICOM3024-2GX front panel

Figure 3-3 Front panel

LED Indicators

The indicators on the front panel of SICOM3024 can show system operation and port status, helping detect and eliminate faults.

Table 3-1 describes the meanings of all indication lights on the front panel.

Table 3-1 descriptions for LED indicators

LED Condition

RUN1

Blinking

1Hz

OFF

System state LED

Switch operates normally

Switch not operate

State

-10-


Gigabit Optical fiber interface state LED（optical fiber interface G0、G1、G2、G3）

DXP On

Effective network connection has been established for the port.

Ethernet RJ45 port state LED

Each RJ45 Ethernet port has two indicators, a yellow lamp and a green lamp. The yellow lamp indicates port speed, and the green lamp indicates port link state.

10M/100M On 100M working status（i.e. 100Base-TX）

(Yellow)

Off

10M working status (i.e. 10Base-T）

On

Effective network connection has been established for the port

LINK/ACT

（ Green）

Blinking

Off

Network activities are available at the port

No effective network connection has been established for the port.

3.2 Interface Description

3.2.1 Gigabit Optical Fiber interface

SICOM3024 offers two or four pairs of redundant 1000Base-FX full duplex single mode or multi-mode optical fiber interface (LC connector), or

1000Base-TX RJ45 (SFP connector) interface. Optical fiber interface should be used in pairs (TX and RX are a pair), TX interface is the transmitting end connected to the receiving end RX of the optical fiber interface of another remote switch; RX is the receiving end connected to the transmitting end TX of the same optical fiber interface of the same remote switch.

Figure 3-4 SFP Plug and Play unit

-11-


Gigabit SFP FX/TX Plug and play steps：

Insert SFP unit，Figure 3-4： z There are two breaks on Fiber-port (LC) and one break on Ethernet port

(RJ45) of SFP unit.

Insert the SFP into case backward to the PCB board. The position is right when you hear a sound. Ready for use if the SFP handle horizontal with connector.

Pull SFP unit: z The fiber part could be separate from SFP case when angle 90 degree between handle of SFP unit and connector.

Pull out the fiber part from case.

器件豁口

器件笼子

光器件拉手

Figure 3-5 SFP Process for Plug and Play

3.2.2 Optical Fiber interface

SICOM3024 offers eight pairs of redundant 100Base-FX full duplex single mode or multi-mode optical fiber interface, with port number of 17~24 and SC or FC connector. Optical fiber interface should be used in pairs (TX and RX are a pair),

TX interface is the transmitting end connected to the receiving end RX of the optical fiber interface of another remote switch; RX is the receiving end

-12-

Chapter Three Hardware Structure connected to the transmitting end TX of the same optical fiber interface of the same remote switch. Two pairs of redundant 100Base-FX optical fiber interface can be used to form an optical fiber redundant ring network. In the event of the system fault, the recovery time of the redundant ring network is less than 50ms, effectively increasing the reliability of network operation.

3.2.3 RJ45 interface

SICOM3024 offers six 10Base-T/100Base-TX RJ45 Ethernet ports numbering

1~16（24. Each RJ45 port has self-adaptation function, support MDI/MDI-X connection and can be connected to end equipments, servers, hubs or other switches in straight-through or cross-over way. Each port supports IEEE802.3x self-adaptation, so the most suitable transmission mode (half duplex or full duplex) and data rate (10 Mbps or 100Mbps) will be automatically selected (the connected equipment should also support this characteristic). If the equipment connected to these port does not support self-adaptation, the ports will be able to send at proper speed but transmission mode is default as half duplex.

LED indicators

The indicators on the front panel of SICOM3024 can show system operation and port status, helping detect and eliminate faults.

Table 3-1 describes the meanings of all indication lights on the front panel.

Table 3-1 LED indicators

LED

Conditio n

State

System state LED

RUN1

Blinking

1Hz

OFF

Switch operates normally

Switch not operate

Gigabit Optical fiber interface state LED（optical fiber interface G0、G1、G2、G3）

DXP On

Effective network connection has been established for the port.

Ethernet RJ45 port state LED

Each RJ45 Ethernet port has two indicators, a yellow lamp and a green lamp. The yellow lamp indicates port speed, and the green lamp indicates port link state.

-13-

-14-


10M/100M

On

(Yellow)

Off

LINK/ACT

（ Green）

On

Blinking

Off

100M working status（i.e. 100Base-TX）

10M working status (i.e. 10Base-T）

Effective network connection has been established for the port

Network activities are available at the port

No effective network connection has been established for the port.

Power input terminal

DC24V or DC-48V: Three-wire terminal with interval of 3.81 ㎜ is used for power connection. The diameter of power cable is less than 1.5 ㎜.

Connection sequence is shown in Figure 3-7. Connection and mounting procedures are as follows:

1． Strip 5mm-long sheath from power cable and twist the bare copper wires together into a bundle;

2． Use a 2.5 ㎜ one-slot screwdriver to unscrew the “power cable locking screw”, insert the power cable into the hole at the terminal tail, and screw down the “power cable locking screw”;

Insert the power terminal into the DC power socket of the equipment and use a 2.5mm one-slot screwdriver to screw down the two “terminal locking screws” to firmly connect the terminal with the power connector.

端子锁紧螺钉

电源线锁紧螺钉

电源地

+24V

保护地 PG

Figure 3-7 DC Power

AC Power input terminal：

AC Power input terminal：2A fuse is used in SICOM3024 Industrial

Ethernet Switch AC power. Step by step phase as show in following figure.：


Figure 3-6 a STEP 1

Figure 3-6 b STEP 2

RS232 Network management interface（CONSOLE）

The network management interface of SICOM3024 is shielded RJ45 connector and its interface communication standard is 3-wire RS232. Users can use a network management cable with end bearing RJ45 plug and another end DB9F plug to connect the network management interface of SICOM3024 with the 9-pin serial port of the control computer. Operating the local management software to set up SICOM3024 by CLI. The wiring sequence for network management interface of SICOM3024 and the 9-pin serial port of PC computer is shown in

Figure 3-9.

-15-

-16-


PC机9针串口

SICOM3024

CONSOLE口

1

1

6

8

5

Figure 3-9 CONSOLE wiring diagram

9


第四章 Hardware installation

4.1 Installation requirement

As a monomer structure switch. It can be fixed on standard 19’ rack .

Before installation, make sure all condition match the installation requirement.

1：Power supply: （18VDC～36VDC）。

-condensing) 10％～95%（

3：Earth resistance: <5

Ω

4：Make sure all fiber are ready for use

5：Avoid sunshine, and strong EMC area

4.2 Mainframe installation

4.2.1 Stable rack mounting

SICOM3024 Industrial Ethernet switch proved rack mounting, before mounting; make sure the following is ready:

1． Make sure the rack is burliness, and there still have enough space for

SICOM3024.

2． The power supply is available for SICOM3024.

After selecting the mounting location. Fix the SICOM3024 as following figures.

KIEN3016

Industrial Ethernet Switch

9 10 11 12 13 14 15 16

10M/100M

LINK/ACT

Figure 4-1 SICOM3024 mounting drawing

-17-


机架安装立柱

M5法兰安装螺钉

KIEN3016

Industrial Ethernet Switch

RUN A B C D

DPX

LINK

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

10M/100M

16

LINK/ACT

Figure 4-2 Mounting the SICOM3024 on the rack

4.3 Cable connecting

After fixed the SICOM3024,the next step is connect the cables.

1：Service interface.

SICOM3024 has 10Base-T/100Base-TX Ethernet RJ45 port, can connect the terminal equipment with cable directly.

2：Connecting power

The power supply to the SICOM3024 should be DC24V, after connecting all the cable.

The equipment can be used

4.4 Optical Fiber Connection

SICOM3024 provide two or four redundancy duplex 100Base-FX ports (single mode or multi-mode) SC or FC type are available.

CAUTION ：

This switch use fiber as transmitting medium, in order to avoid hurt by the laser, don’t look the fiber port and terminator directly after electrifying

The connecting procedure as below

-18-

Chapter Tour Hardware installation

1: Remove the rubber cape of the fiber interface. and keep them for 2:protecting the fiber terminator when unused

3: Inspect the fiber terminator and ensure it is in good condition

4: Connecting the fiber port between the switch and terminal equipment .show as picture 4-6.

4.5 Cable wiring

Cable wiring should meet the following requirements:

1． Before cable wiring, check whether the specifications, models and quantities of all cables comply with the construction drawing design and contract requirements.

2． Before cable wiring, it is necessary to check whether there is damaged cable and whether the cables are accompanied by ex-factory records and vouchers attesting their quality such as quality assurance certificate etc.

3． The specifications, quantities, route directions and laying position of the cables to be laid should meet the design requirements of construction drawings. The laying length of each cable should be determined according to its actual position.

4． No intermediate break or joint is allowed for the cables to be laid.

5． User’s cables and power cable should be laid separately.

6． Inside walkways, the cables should be properly arranged in good order, with uniform, smooth and flat turnings.

7． Cables should be straightly laid in cable channels. Extruding of cable from cable channels to block other outlet or inlet holes is not allowed. The cables at the outlet part of cable channel or at turnings should be bundled and fixed.

8． If cables, power line and grounding conductor are laid in the same channel, cables, power line and grounding conductor should be not folded or blended together. If a cable line is overly long, coil and place it in the middle of the cabling rack, do not let it cover on other cables.

9． When laying the pigtail, avoid knotting of optical fiber cable, minimize the amount of turnings and avoid turnings with overly small radius. Bundle pigtails in proper tightness and avoid too tightly bundling. If laid on a cabling rack, it

-19-

-20-


should be placed separately from other cables.

10． There must be the relevant marks at both ends of cable and the information on the marks should be explicit to facilitate maintenance.

Attention:

When laying pigtails, prevent optical fiber cable from knotting, minimize the amount of turnings and avoid turnings with too small radius, because turning with too small radius will result in serious consumption of optical signal of links, affecting communication quality.


第五章 Test methods

5.1 Self inspection

When electrify the equipment, all service indicator light will flash, after the first, the

POW indicator light will light and the RUN will flash(not flash be setting)

5.2 TP Port Test

Showing as Picture 5-1.after electrifying, connect the TP port with the computer, send the “ping” command each other. Each part should receive complete command. The yellow indicator light will light (100M state)or quench (10M),these state shows the TP port are in good condition

PC1 PC2

图 5-1 TP port test

5.3 Fiber Port Test

Connect two equipments as picture 5-2, and connect each equipment with computer through TP port. Send the “ping” commands each other, Both part should receive complete command, and the LINK/ACT lamp should light. these show the Fiber port are in good condition.

-21-

-22-


PING commands example：

图

5-2 Fiber test

Suppose the IP address for one computer is. 192.168.100.10 and the other one is

192.168.100.11, operate the “begin” menu on the one computer, and select the: operation” item. input “cmd” or ”command”, sending Ping 192.168.100.11 –l 1000 -t， operate the “begin” menu on the second computer, and select the: operation” item. input “cmd” or ”command”, sending ping 192.168.100.10 –l 1000 –t. return “Reply from 192.168.100.11：bytes=1000 time<10ms TTL=128”,for the second computer,

Return “Reply from 192.168.100.10：bytes=1000 time<10ms TTL=128”,after ten minutes for operating ,use CTL+C command to Stat. the missing rate. If the missing rate is “0” shows the equipment are in good condition


第六章 Networking Method

6.1 Networking

SICOM3024 provides sixteen to twenty-four 10Base-T/100Base-TX Ethernet RJ45 port. each port can connect the terminal directly, and two redundancy 100Base-FX

Fiber ports.(single or multi-mode) with the redundancy Fiber port ,SICOM3024 can build redundancy ring .the recover time is less than 50ms,it can be widely used in various Industrial field.

图 6-1 SICOM300 build the redundancy ring

6.2 System configure

SICOM3024 is a integrative industrial Ethernet switch, has 16-24 ix

10Base-T/100Base-TX Ethernet RJ45 port. And two redundancy fiber ports (single or multi-mode),the power supply for SICOM3024 should be DC24V.detailed configure showing as table 6-1

Table 6-1 SICOM3024 configure table

-23-

-24-


Model

SICOM3024-4GX-24T

SICOM3024-2GX-24T

SICOM3024-24T

SICOM3024-2GX- 16T -nS（M）

8SICOM3024-16T-nS（M）

Description

4 × 1000Base-LX/T,

24 × 100Base-TX，

Support WEB-managed 、 Telnet 、 SNMP-based management 、RMON、DT-ring2.0,RSTP

2 × 1000Base-LX/T,

24 × 100Base-TX，

Support WEB-managed 、 Telnet 、 SNMP-based management 、RMON、DT-ring2.0, RSTP

24 × 100Base-TX，


2× 1000Base-LX/T,

0- 8 pair Sigle(multi) mode Fiber port,

16×100Base-TX，


0- 8 pair Sigle(multi) mode Fiber port,

16×100Base-TX，


注： n 等于 0-8


第七章 WEB Management Software

SICOM3024 support WEB page management, Through web page can monitor the working state of the switch and can configure the switch through web page.

7.1 Login Web service

Connecting the switch with a computer, input the IP address “192.168.1.71” in the IE browser, a window will appear as Figure 7-1,the default password is 123.click confirm to enter.

Figure 7-1 Login interface

The main page as Figure 7-2

The left page shows the management tree menu. Include equipment state, basic configure, advanced configure, equipment management, save all amend. Recover default and so on. ,each menu may include some child menu.

-25-


Figure 2 Main Page

7.2 Equipment State Display

The Equipment state display. Menu include: basic information. Port state, port flow.

7.2.1 Basic information

Click basic information and enter the interface, showing as Figure 7-3, including

MAC address, IP address, software edition, hardware edition etc

Figure 3 Basic Information

7.2.2 Port State

Click port state and enter the page showing as Figure 7-4, this page can show the link state, link speed, duplex/semi duplex and flow control state

-26-


Figure 7-4 Port State

7.2.3 Port Flow

Click Port flow and enter the page ,the page display each port flowing Stat information.

Figure 7-5 Port Flow

7.3 Equipment basic configuration

The Equipment basic configure page include IP address, equipment name, port configure, password modify, software edition inquiry, software update.

-27-


7.3.1 IP address configuration

Click the IP address menu and enter the page (as Figure 7-6),this page support IP address modify. Child network mask, gateway modifies. After modifying, click application .and reset the switch.

Figure 7-6 IP Address Configuration

7.3.2 Equipment name configuration

Click the “equipment name” menu and enter the interface show as Figure 7-7, change the equipment name as you want and click application.

Figure 7-7 Equipment name Configure

7.3.3 Port configuration

Click Port configures on the lift menu list and enters the interface show as Figure

-28-


7-8,this menu can realize the port state configure ,automatic consulting. Speed configure, duplex state configure, flow control .after configuring, click application button to take effect.

Figure 7-8 Port Configure

7.3.4 Password change

Click Password change menu and enter the interface shown as Figure 7-9, input the old password, new password and reconfirm the new password. After doing so, click apply button to take effect.

Figure 7-9 Change Password

-29-


7.3.5 Software edition query

Click the Software edition query menu and enter the interface show as figure 7-10, two editions will appear. One is activities and another is inactive. This function mainly use for software update.

Figure 7-10 Software edition inquiry

7.3.6 Software update

Click the Software update menu and enter the interface show as Figure 7-11, for detailed update method please refer to appendix D

After entering the WEB management homepage, z

-30-

Figure 7-11 Software Update

Configure the server address, username, password and select the software for updating, till it update succeed.

Click the navigation item and inquiry the software edition, put the updated one as the default and select reset bottom


After 30 seconds, start the WEB management system. and make sure it was completely updated..

7.4 Advanced Configuration

Advanced Configuration includes Port Traffic Control, VLAN Configuration, Port

Mirroring, Port Aggregation, Redundant Ring Configuration, Port Priority Setting and

Other Configuration of switch.

7.4.1 Port Traffic Control

Click the “Port Traffic Control” on left control menu to enter the interface shown as

Figure 7-12, in this control interface, you can set transmit and receive rate of each ports. The granularity for FE ports is: 128K, 256K, 512K, 1M, 2M, 10M, 50M, 100M; for GE ports is 100M, 500M, 1000M. Click “apply” when you finished the configuration.

Figure 7-12 Port Traffic Control

7.4.2 VLAN Configuration

Click the “VLAN Configuration” on left control menu to enter the interface shown as

Figure 7-13 Choose the VLAN mode: Based on 802.1Q and then click “add” to enter the interface shown as Figure 7-14.

Fill in the VLAN Name, VLAN ID (default ID is 1), and choose VLAN member, Tag /

-31-


Untag. After configuration, click “apply” to save.

Attention：Default

VLAN ID is “1”, Available VLAN ID range is from ”2~4093” .

Figure 7-13 Add VLAN

Figure 7-14 VLAN Configuration

7.4.3 Port Mirroring Configuration

Click the “Port Mirroring” on left control menu to enter the interface shown as Figure

7-15, choose the ports you want to mirror to, the port range is from port1 to port24 and

G0, G1; choose the mirrored port No. There are 3 types of data can be mirrored: TX,

-32-


RX, TX&RX. After configuration, click “apply” to save.

Figure 7-15 Port Mirroring Configuration

7.4.4 Port Aggregation Configuration

Click the “Port Aggregation” on left control menu to enter the interface shown as

Figure 7-16,

SICOM3024 supports two aggregation groups. Click , to add and delete the ports you want to aggregate. After configuration, click “apply” to save.

Attention：

G0、G1 can only aggregated with each other, and can not

aggregated with FE ports.

-33-


Figure 7-16 Port Aggregation Configuration

7.4.5 Redundant Ring Configuration

Click the “Redundant Ring Configuration” on left control menu to enter the interface shown as Figure 7-17, and click “add” to enter the interface as Figure 7-18. Fill the

Domain ID number (ID = 1~32 ) and the Domain Name; set the type of station.

Mater/Slave; choose port number of the ring (suggest G0, G1 for GE ring and FE23,

FE24 for FE ring). After configuration, click “apply” to save.

Attention：The ID number in one redundant ring must be same.

Redundant Ring network support DT-Ring Protocol.

Figure 7-17Redundant Ring Configuration

-34-


Figure 7-18 Detail of Configuration

Figure 7-19 Detail of Inquiry

7.4.6 Port Priority Setting

Click the “Port Priority setting” on left control menu to enter the interface shown as

Figure 7-20. Enable QOS mode, and set the port’s priority level as High/low. After configuration, click “apply” to save.。

Attention：SICOM3024 support 2 priority level

-35-


Figure 7-20 Port priority Setting

7.4.7 Other Configuration

Click the “Other Configuration” on left control menu to enter the interface shown as

Figure 7-21. This interface includes Broadcast Storm Control and MAC address aging configurations.

Broadcast Control includes 5 Options: disable, 1/2, 1/4, 1/8, 1/16. when broadcast package reach 1/2, 1/4, 1/8, 1/16 of total bandwidth, the broadcast packet will be discarded. Disable option means no limitation of broadcast package.

MAC address aging time includes 4 options: disable, 150s, 300s, 600s

-36-


Figure 7-21 Other Configuration

7.4.8 SNMP Configuration

Click the SNMP configuration on left control menu to enter the interface shown as

Figure 7-22. Enable SNMP mode, and set IP address of TRAP service and port number of it. After configuration, click “apply” to save.

Figure 7-22 SNMP Configuration

7.4.9 IGMP-SNOOPING

Click the IGMP- SNOOPING configuration on left control menu to enter the interface shown as Figure 7-23. IGMP-SNOOPING-STATUS as “ENABLE”；AUTO DETECT

STATUS as “ENABLE” . After configuration, click “apply” to save.

-37-


Figure 7-23 IGMP- SNOOPING

7.4.10 ACL list control

Click the ACL configuration on left control menu to enter the interface shown as

Figure 7-24. Enable SNMP mode, and set IP address of TRAP service and port number of it. After configuration, click “apply” to save.

Enable Port Acl Mode Set, select port state FE1~24、G0~G3 as “none”、“reject”、

“accept”. After configuration, click “apply” to save.

Enable Port Acl MAC Set, fill in MAC address in port FE1~24、G0~G3. After configuration, click “apply” to save.

Figure 7-24 ACL

7.5 Device Management

Device management includes: Save All Changes and Return to Default

-38-


Click the “Save All Changes” on left control menu to enter the interface and click

“Save” to save all the changes on WEB page configuration.

Click the “Return to Default” on left control menu to enter the interface and click

“Return to default” to reset all configurations.

-39-


第八章 CLI Command

This chapter mainly introduce how to config SICOM3024 via CLI command line, and the explanation of commands.

8.1Connect to the Switch and Login

8. 1.1 Command Line

You can connect and log in via Serial port or Telnet

To log in via Serial Port, connection between serial port and PC is required. The detailed connection method and serial line sequence, please refer to Chapter 3.2.3

Switch on the switch, open the serial port and type “Enter”, you can see the prompt

(default is “kyland>”)

Attention：

If users want to remain the change after the switch reboot, please use the

“write flash” command after you configuration to save the changes. See the Common Command

Description

。

8.1.2 Command syntax

This part describes the steps to enter CLI command line.

Step one: type “enable” after you enter the command interface to enter the command line mode. It will show the prompt kyland#

-41-


Step two：Type the command name. If the command doesn’t contain any parameter options, go to step three. If the command has parameter options, please type the parameter and the key value.

Command parameters are normally refers to the user input parameter, which could be a range of Numerical Value, Chat Script or IP address. The key value is the objective controlled by the command. If the command need more than one parameters, please type each parameter and key value follow the command help, until the <cr> display in the command window.

Step three: After input the full command, type “enter”

Example (in the case of no parameters) kyland# exit

“exit” is a command without parameter, command name is “exit” when input this command, type “enter” to finish.

Example (in the case parameters required)

8.1.3 Syntax help

The help is integrated in command line interface. If not sure about the syntax, please type the first part with the wildcard “?” of “space + ?” The command line will automatically display rest of command and the possible command list. Users can choose the right command and type rest part until the command line show “<cr>”.

Then type “enter” to finish.

8.1.4 Use syntax help to fill the command

When user type the first part of a command and “Tab”, management soft ware can fill rest command automatically and move the cursor to the end. If the first part marches more than one command, the possible command list will be displayed.

For example：

-42-


Step one: type command

KYLAND#show

Step Two: type a “space”, and then type “Tab”. the information as below will be displayed: broadcontrol Broadcontrol clock Display the system clock config System configuration fdb Fdb history Display the session command history igmp Igmp snooping protocol interface Interface status and configuration manager Management station status memory System memory statistics information dt-ring dt-ring protocol rstp Rapid spaning tree protocol running-config Current operating configuration snmp SNMP status switch Show switch status telnet Telnet configure information timer Show timer message trunk Show vlan information uptime Display the system uptime version System hardware and software status vlan Show vlan information

Above information are the possible commands users can use after the “show” command. Users can type the correct command or part of the command with a “Tab”.

-43-


8.1.5 Symbols in the command

In the management software, there only one type of symbol supported, which is “<>”.

It means in this part of the command a parameter is required.

For example： dt-ring new <1-32> domain <1-32> master

2-5

8.1.6 Types of Command

Normally the command in an angle bracket “<>” is command parameters. There are four types of command parameters in this series switches.

Numerical Value

When the numbers in the angle bracket is connected by a Dash, which means the parameter is a number between this range.

For example: <1-255> means user can input any integer greater than 1 and less than

255. such as “2”.

IP address

The “A.B.C.D” in angle bracket means it is IP address. User must input a correct IP address.

For example: 192.168.0.1 is a leag

Chat Script

If the content in the angle bracket is not above two forms, it means the input parameters are chat script or hex number. Uses can input a “?” at this place to know the detail parameter description.

For example: <macaddr> means the required input is a hex Mac address, Such as

005023344325 is a legal Mac address. <name> means the input is a chat script as the subject’s name.

-44-


8.1.7 Command abbreviation

Command abbreviation means users can only input command or the first several letters, as long as that part don’t have different meaning, switch will recognize that command.

Users can just type “enter” to run that command. The user input parameter, such as

VLAN name (in the blow example, it is “market”) etc. need to be fully input

Example, add port1 to “market” VLAN as untagged form

KYLAND>

KYLAND>enable

KYLAND#config terminal

KYLAND(config)#

KYLAND(config)#vlan 2

KYLAND(config-vlan2)#description market

KYLAND(config-vlan2)#add port 1 untag priority 0

(Above command line can be abbreviated as:)

KYLAND>

KYLAND>ena

KYLAND#con ter

KYLAND(config)#

KYLAND(config)#vlan 2

KYLAND(config-vlan2)#desc market

KYLAND(config-vlan2)#add port 1 un pr 0

(Above to parts have identical function)

-45-


Attention：when use abbreviated commands, users must input

enough letters to ensure there is no different meanings

8.1.8 History commands

The management soft ware can memorize the latest 10 commands.

Users can use “show history” to display the recent command list:

Users can also use up or down in you keyboard to choose the above or next history command.

Example: after log in to the system, input: show history

Follow information will be displayed: enable

8.1.9 Frequently used commands

This part mainly describe several frequently used commands, some specially used commands will be discussed in the next chapters. Command lines provide two types of modes: one is Read Only, anther is Configuring Mode. At Read Only mode, users can only examine part of system configuration information. At Configuring Mode, users can examine or configure all the system configuration information. At this mode, users can use some commands to enter certain protocols’ independent configuration mode.

Such as: “KYLAND#” is interface configuration mode.

At Read Only mode, the prompt end with “>” i.e. “KYLAND>”

At Configuring mode, the prompt end with “#” i.e. “KYLAND#”

¾

enable

at Read Only mode, to end Configuring mode use this command:

KYLAND>enable

For Example:

-46-


KYLAND>enable

Press “enter” and system will ask for password

Password:

After input password correctly, enter the Configuring mode.

KYLAND#

Attention：at default status, password is empty.

¾

enable password <1-20>

At Configuring mode, users can set password.

Using the command below:

KYLAND(config)# enable password <1-20>

¾

exit

To return to above level, use command:

exit

¾

show version

To show the software version, use command:

show version

¾

help

At any mode, to get information of how to use “?” or need help, use command help

For example:

Kyland# help

2

-Help may be requested at any point in a command by entering a question mark '?'. If nothing matches, the help list will be empty and you must backup until entering a '?' shows the available options.

-47-

-48-


Two styles of help are provided:

1. Full help is available when you are ready to enter a command argument (e.g. 'show ?') and describes each possible argument.

Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input

(e.g. 'show pr?'.)

¾

Hostname

At Configuring mode, users can use below command to set host name:

hostname <hostname>

Attention：

In same network, please lay out all hosts’ names with same naming strategy.

For example：

Kyland(config)# hostname userA userA(config)#

¾

clear

At any modes, to clear screen display use command：clear

Attention：

Use this command when there are too much useless information displayed on the screen.

¾

show running- config

At configuring mode, to display current system configuration, use this command:show

running-config

Attention：This is a very useful command to help system


administrator examine current system configuration status.

For example：

!config

dt-ring new vlan domain 1 master

rstp hello-time 15

rstp forwarding-delay 0

!interface-eth 1

vlan tag 2

no flow-control

rate ingress 0

rate egress 0

!interface-eth 2

no auto-negotiation

duplex

no flow-control

rate ingress 0

rate egress 0

!interface-eth 3

no flow-control

rate ingress 0

rate egress 0

-49-

-50-


!interface-eth 4

no auto-negotiation

duplex

no flow-control

rate ingress 0

rate egress 0

!interface-eth 5

no flow-control

rate ingress 0

rate egress 0

!interface-eth 6

no auto-negotiation

duplex

no flow-control

rate ingress 0

rate egress 0

!interface-eth 7

no flow-control

rate ingress 0 rate egress 0

!interface-eth 8

no auto-negotiation


duplex

no flow-control

rate ingress 0

rate egress 0

!interface-eth 9

no auto-negotiation

speed 1000m

duplex

no flow-control

rate ingress 0

rate egress 0

!interface-eth 10

no auto-negotiation

speed 1000m

duplex

no flow-control

rate ingress 0

rate egress 0

!interface-down

!interface-backup

-51-

-52-


!vlan 2

description market

add port 1 untag priority 0

!dt-ring 1

protocol enable

ringport add 2

ringport add 5

!config terminal

fdb agetime 300

no bcast-control

¾ save

At configuring mode, to save all changed configuration, use this command

:

Save

Attention：If users want current configuration available after

system reboot of power switched off, please use this command to save all changed configuration.

For Example：

Kyland# save

Preparing configuration data to save...Done.

Starting write configuration data to flash...Done.

Configuration save to flash successfully.

¾ load default


At configuring mode, to delete all saved system start configuration, please use this command

load default

-1

Attention：If users want to reset switch start configuration, please

use this command to delete all changed configuration.

For example：

KYLAND# load default

Trying erase all configuration from flash, please wait ...... finished.

Successfully erase all configuration info from flash.

8.2 Common management methods

SICOM3024 series switches are mainly managed by the following methods:

using a terminal (or simulation software) to connect to switch’s console port, to visit switch’s CLI interface

using Telnet to manage switch (not available at the moment) using SNMP to manage switch (not available at the moment)

8.3 Using Console port to manage switch

Users can connect to switch’s CLI interface via the RJ45 port marked with “console” on the switch front board.

For SICOM-3000 series, the configuration of Console port is as below:

Baud rate：115200

Bit ：8

CRC ：No

Stop bit ：1

Flow control ：No

-53-


When connect switch with Console port, VT100 simulation terminal is recommended.

Configuration steps are: at hyper terminal interface, open “file” menu, select “attribute” tool bar, and click “configure” at the window appeared, then select VT100 in the list.

8.4 Configure Port

8.4.1 Enabled/Disabled Port

For a switch that is started, all the ports are default enabled. You can also configure each port state based on requirements. To enable or disable one/more ports, you can use the following command:

KYLAND(config-if-eth1)#Lock/no lock

EX：

KYLAND>enable

No password set!


KYLAND(config)#interface ethernet 1

KYLAND(config-if-eth1)#lock

KYLAND(config-if-eth1)#no lock

8.4.2 Configure Port Rate, Duplex Mode and Flow Control

Fast Ethernet port can be connected in 10Base-T or 100Base-TX networks and works in half or full duplex mode, which require you to configure it according to application.

All ports are default set as adaptive mode. The software will adjust the port rate and duplex mode automatically. You can also configure the rate, duplex and flow control mode manually.

Attend：

To configure the rate, duplex and flow control mode manually, you must close the adaptive mode firstly.

-54-


¾ Configure adaptive mode

Use the following command to configure adaptive mode:

KYLAND(config-if-eth1)#auto-negotiation/ no auto-negotiation

¾ Configure port rate:

Use the following command to configure port rate:

KYLAND(config-if-eth1)#speed 10m/100m/1000m

¾ Configure duplex:

Use the following command to configure duplex mode：

KYLAND(config-if-eth1)#Duplex/ no duplex

¾ Configure flow control mode

Use the following command to configure flow control mode：

KYLAND(config-if-eth1)#Flow-control/ no flow control

Attend：

The 100Mbit and Gigabit fiber ports are both default set as closed auto-negotiation and full-duplex. The auto-negotiation, duplex and rate can not be

configured.

8.4.3 View Port

Use the following command to view information on all ports:

KYLAND#show interface ethernet

Use the following command to view information on some port:

KYLAND#show interface ethernet <1-10>

8.4.4 View/Delete Port Statistics

Use the following command to view the port statistics:

KYLAND(config-if-eth1)#show stats

Use the following command to delete the port statistics and make it restart to count:

KYLAND(config-if-eth1)# clear stats

-55-


Attend：

After the port statistics are deleted, the port data are set as zero.

8.5 TRUNK

You can enlarge the bandwidth of switches by creating trunk group. Trunk will bind several ports to act as one logic port. For example, the trunk group in the VLAN is a logic port. Trunk also offers assurance for the data packets between clients. When a port in the trunk group fails, the data packet can be distributed to other port and transmitted. If the fault port recovers, the data packet will be distributed into all ports in the trunk group to increasing the bandwidth of switch. SICOM3024 supports totally 3 trunk groups. 7 FE ports can be grouped into 2 trunks (port 1 can not be added into any trunk group). 2 GE can be grouped into one trunk.

5

Attend：

You must set up trunk both in two connected switches or network loop will happens and cause the switch to fail.

The ports in the trunk group must be in the same duplex state and rate, and must be in the sale VLAN.

It is very useful to increase transmission speed to create trunk group when more than 2 ports of one switch need to communicate with other switch.

Configure TRUNK

KYLAND>enable

No password set!


KYLAND(config)#trunk <1-3>

KYLAND(config-trunk1)#create

KYLAND(config-trunk1)#add port <1,10>

-56-


8.6 Port Mirroring

SICOM3024 supports port mirroring，which directs all data of given port to the mirrored port for diagnostics.

Configure mirroring port:

SICOM3024 only supports one mirroring port, to use the following command:

KYLAND(config)#interface ethernet <1-10>

KYLAND(config-if-eth1)#mirror enable

KYLAND(config-if-eth1)#mirror add ingress port <1-10>

mirror enable is to enable mirroring port: mirror add/delete ingress/egress port <1-10> is for adding or deleting mirrored port.

8.7 Port Prioritization

Switch supports port prioritization by which the important task is protected. You can configure the priority of the ports(low and high). To validate port prioritization, you need to enable QOS firstly. When QOS is enabled default, all ports are in low priority.

You need to configure the priority by command.

¾ Qos enabled command：

KYLAND(config)#qos enable

¾ Use the following command to configure priority：

KYLAND(config)#qos add/delete hqport <1-10>

8.8 VLAN

8.8.1

VLAN Overview

VLAN（Virtual Local Area Networks）is a devices group which seems to work in the same physically local area network. It makes network manager to manage more easily by create VLAN for switches. Any group of any port(even all ports) can be considered as a VLAN, which is not limited by hardware physical connection. You can divide ports, create and define VLAN by command easily.

-57-


SICOM3024 supports total 4093 different VLANs. The name of each VLAN can be started with any letter and less than 30 characters, which can only be letters, figures or

“_” other marks are not allowed.

VLAN name is only a local mark, which means the name is only meaningful to the switch where the VLAN is set.

Attend：

For better network management, you should name VLAN universally.

8.8.2 Default VLAN

Each SICOM3024 has a factory default VLAN which is set as below:

VLAN name is default ；

Including all ports；

All ports of default VLAN are untagged except for CPU port(tagged);

default VLAN’s ID is1；

default VLAN can not be changed；

When a port is added into a VLAN in untagged way, it will be deleted in the default

VLAN automatically. When a port is deleted in a VLAN in untagged way, it will be automatically added into the default VLAN.

8.8.3 Create VLAN

In the configuration mode, to create VLAN won’t be shown. The VLAN will be deleted when there is no port in it. When a port is added into the VLAN in tagged/untagged way, VLAN is created automatically.

Use the following command to enter into VLAN configuration mode:

KYLAND(config)#vlan <1-4093>

<1-4093> is the ID range of VLAN。

-58-

8.8.4 Change VLAN Name

When you create a VLAN and want to change the name only, you can use the


following command:

KYLAND(config-vlan2)#description <1-31>

8.8.5 Add/Delete VLAN Port

The ports of SICOM30240 can be added into a VLAN in two ways:

IEEE 802.1Q tagged

IEEE 802.1Q untagged

At default, all ports are added into default VLAN in untagged way.

In untagged way, a port can only be in one VLAN. In tagged way, a port can be in more than one VLAN simultaneously. Each port in VLAN can have only one default

VID. The port’s default VID is the VID of one of the VLANs where the port belongs to.

The data without 802.1Q Tag value received in the port will be transferred in the

VLAN of default VID.

¾

Use the following command to add untagged port into VLAN：

KYLAND(config-vlan2)#add port <1-10> untag priority <0-7>

<1-10> is for port number；<1-7> is for the port priority。

¾

Use the following command to add tagged port into VLAN：

KYLAND(config-vlan2)#add port <1-10> tag

<1-10> is for port number。

¾

Use the following command to delete VLAN port：

KYLAND(config-vlan2)#delete port <1-10>

<1-10> is for port number。

8.8.5 Show VLAN

You can view the VLAN which has been configured by using the following command:

¾ Show some VLAN settings: show vlan <2-4093>

<2-4093> is for VLAN ID

¾ Show all VLAN settings:

-59-


Show vlan

8.9 IGMP Snooping

8.9.1 IGMP Snooping overview

IGMP（Internet Group Management Protocol）is a part of IP protocol group to support and manage the IP multicast between PC and router. Multicast allow to discover resources and reduce network load the minimum, realizing the most efficient transmission.

SICOM3024 supports IGMP Snooping, which is used to monitor and process the

IGMP report between PC and router. IGMP Snooping enables the switch to track each of its physically connected group members. It works between PC and router and manages group members.

SICOM 3024 supports not only automatic inquiry, but also restraint function. Its apply network environment without layer-three switch.

8.9.2 Configure IGMP Snooping

8.9.2.1 Automatic inquiry of IGMP Snooping

It must configure IGMP automatic inquiry function if without layer-three switch. To start IGMP, you need to choose router-port firstly. Router-port is the connecting port of multicasting server

¾ Enable IGMP

KYLAND(config)#igmp auto-query enable

¾ Disable IGMP

KYLAND(config)#igmp quto-query disable

8.9.2.2 Enable/Disable IGMP Snooping

In the setting mode, use the following command to enable/disable IGMP：

¾

Enable IGMP Snooping

-60-


KYLAND(config)#igmp enable

¾

Disable IGMP Snooping

Attend：

Router-port. You must configure router-port before start IGMP

8.9.2.3 Display IGMP Snooping

In configuration mode to display information about team member:

¾ Display IGMP Snooping

KYLAND#show igmp-snooping

8.10 DT-Ring

8.10.1DT-Ring Overview

DT-Ring is develop and owned by Kyland ltd proprietarily. This protocol test the state of ring port and pass few protocol messages to decide the state of port on ring and ensure the redundant ring network work properly, to make the redundant Ethernet fast and stable, and finally to meet the needs of industrial communication.

Network mode as figure 8-1；

主站

从站

从站

从站

Figure 8-1 DT-Ring Network Mode

-61-


Configuration Instruction:

¾

On the same switch, can configure several domains to set the tangency ring network mode

¾ In the same ring, every switch needs to configure same ID of domain. For the convenience of maintaining, to set the same name of domain is better.

¾ In one ring, only one master, others are all slave

8.10.2 Create/Delete DT-Ring Domain

¾ Create DT-Ring

KYLAND(config)#dt-ring new <1-31> domain <1-32> master/slave

The first parameter is domain name, the second one is domain ID

Can set DT-Ring as master, or as slave.

¾ Delete DT-Ring demain；

KYLAND(config)#mr del domain <1-32>

Attend：

Set

DT-Ring，need to create DT-Ring domain first.

8.10.3 Add/Delete Ring-port

In DT-Ring, need to setup ring-port as needs to consist redundant network protection.

¾ Add Ring-port

KYLAND(config)#mrp <1-32>

KYLAND(config-mrp-1)#ringport add <1-10>

<1-32>indicate domain ID；<1-10>indicate Ring-port ID。

¾ Delete Ring-port

KYLAND(config)#mrp <1-32>

KYLAND(config-mrp-1)#ringport delete <1-10>

<1-32>indicate domain ID; <1-10>indicate port ID

Attend：

-62-


There are only two Ring-ports; if setup just one ring-port may not work properly.

8.10.4 DT-Ring Domain protocol enable/disable

Need to set Enable to make DT-Ring work

¾ DT-Ring domain enable

KYLAND(config)#dt-ring <1-32>

KYLAND(config-dt-ring-1)#protocol enable

<1-32>indicate domain ID

¾ DT-Ring domain disable

KYLAND(config)#dt-ring <1-32>

KYLAND(config-dt-ring-1)#protocol disable


8.10.5 Display DT-Ring Domain State

Display DT-Ring state command, include basic setup and protocol state information.

¾ Display DT-Ring domain state

KYLAND#show mr <1-32>


-63-


Appendix A Twisted-pair and Pin Distribution

For the connection of 10Base-T/100Base-TX, the twisted-pair must have two pair cable. Each pair is distinguished with two different colors. For example, one strand is green, and the other is the alternate of green and white stripes. RJ-45 connector should be equipped at both ends of the cable.

Warning:

Don’t insert a telephone plug into any RJ-45 port. Only use twisted-pair with RJ45 connectors at both ends conforming to FCC standard.

Fig. A-1 Shows how the connector of RJ-45 is numbered please make sure that the inserting direction is correct.

1

8

8

1

Figure A-1 Connector of RJ-45

Pin distribution of 10Base-T/100Base-TX

Unshielded twisted- pair (UTP) or shielded twisted-pair (STP) will be used for the connection of RJ-45: for the connection of 10Mbps, category 3, 4 and 5 of 100 ohm will be used, and cat.5 of 100 ohm will be used for 100Mbps. Additionally, do make sure that the connecting length of any twisted-pair shall not exceed 100 meter.

Port of RJ-45 supports automatic MDI/MDI-X operation, PC or server may be connected with straight-through cable, or connect with other switch or hub. In straight-through cable, pin 1, 2, 3 and 6 at one end of the cable are connected to pin 1, 2, 3 and 6 at the other end of the straight-through cable

-65-

-66-


respectively. Cross-over cable must be used for switch or hub with MDI-X port. The pin distribution of 10Base-T/100Base-TX is listed in the table A-1.

Pin

1

2

3

6

4，5，7，8

Table A-1 Pin distribution of 10Base-T/100Base-TX

MDI-X signal name

Receiving data ＋（RD+）

Receiving data －（RD-）

MDI signal name

Output data＋（TD+）

Output data －（TD-）

Output data－（TD-） Receiving －（ RD-）

Unused Unused

Note: “+”“-”denoting cable polarity.

Definition of straight-through cable from RJ45 (8-pin) to RJ45 (8-pin)

Figure A-2 Cable sequence of straight-through cable

Definition of Cross-over cable from RJ45 (8-pin) to RJ45 (8-pin)

Figure A-3 Cable sequence of cross-over cable


Appendix B Cable Type and Specifications

The cable type and specifications are shown as table B-1:

Table B-1 Cable type and specificati

Connect length or

10Base-T Cat 3,4 and 5 100 ohmUTP

100m（328foot）

RJ-45

100Base-TX

100Base-FX

Cat 5 -100ohmUTP

100m（328foot）

50/125 or 62.5/125μm core

2km（1.24mile） multi-mode fiber（MMF）

RJ-45

SC/FC

100Base-FX

1000Base-T

1000Base-LX

1000Base-LX

9/125μm single-mode fiber

（

SMF）

Cat 5-100 ohm UTP

20km（12.43mile）

SC/FC

100m（328foot） RJ-45

9μm or 10μm core sigle-mode fiber(1310nm)

5km（3.1mile） LC

50/125 or 62.5/125μm core multi-mode fiber （ MMF ）

550m LC

(850nm)

-67-


Appendix C Glossary

10Base-T

100Base-TX

100Base-ＦX

Adaptive

Bandwidth

Baud Rate

Bridge

Terminology Explanation

Twisted-pair standard of Cat3, Cat4 and Cat5 in IEEE specification for 10Mbps Ethernet

Twisted-pair standard of Cat5 or above in IEEE specification for 100Mbps Fast Ethernet

Fast Ethernet which uses one pair of multi-mode or single mode optical fiber to transmit.

A characteristic that is automatically configured to adaptive mode for the speed, duplex and traffic control port.

The information capacity that the channel can transmit.

For instance, the bandwidth of the Fast Ethernet is

100Mbps（bit per second）.

It expresses the signaling rate which is defined as the change times of the status for the electric or optical transmission medium within 1 second.

One of network equipments which run on the layer2 in the OSI layer7 model, and it can be connected to the LAN or network segment which uses the same protocol. It presents the automatic network address learning and network configuration function.

-69-

-70-

Traffic Control

Full Duplex

Half Duplex

MDI

MDI-X

VLAN

Broadcast

Broadcast storm

It is a congestion control mechanism. The network equipment sends the data to the equipment which has overloaded and causes the port to congest. The traffic control can prevent the data packet from loss and avoid the congestion for the port.

It is the Virtual Local Area Network, which means that it takes the network management software to establish the point to point logic network which can cross different network segment and various network on the switching

LAN.

One data packet is sent to all equipments on the network.

Restless forward broadcast frame or multicast frame on bridge caused by the bridge ring.

Use switches to set up the point to point connection among nodes in the LAN and allow them to receive and send data packet at the same time.

The communication for two nodes can only move toward one direction at the same time, but can not move toward both directions.

It is the Medium Dependent Interface, in which, one

Ethernet port is taken as the receiving terminal to connect to the port of other equipment.

Medium Dependent Interface Cross-over


Appendix D FTP Application for Switch

Software Update

You can use web management to upgrade SICOM-3000 software through switch by

FTP protocol (Switch as Ftp client；PC as Ftp server）. Before update, you need to setup the Ftp server；FTP server is well-known software, and can be downloaded on the internet. Here is the steps for configuring FTP server.

1． Install WFTPD in PC. Load WFTPD；shown in figure 1：

Figure 1 WFTPD startup

Type in user name, password, main path; click on Security menu, click on Users/rights, click on the New User in the User/Rights Security Dialog window. As Figure D-2：

FigureD- 2 WFTPD

User Name and Password

Type in your user name in New User window; here is “test”, click OK, as FigureD-3：

-69-

SICOM3024 工业以太网交换机用户手册

Figure 3 WFTPD User Name Setup

In Change Password window, type in the password in New Password and Verify area, for instance ”test”, click OK ;

Figure D-4 WFTPD Password Setup

Set home directory; here is C:\

-70-

Figure D User information setup dialog box

Click Done to finish FTP server setup

2． Upload the software to home directory on FTP server, here is under C:\。

FTP server setup is finished now. For the successful setup we support two software version:

Host and Backup. The Host version is the one we currently used which is not allowed to update for the purpose of protecting software. We use WEB management software to upgrade it, steps：

附录 D 交换机软件升级的 FTP 的应用

3． Enter into WEB management page, click navigation bar to set Update, as

FigureD-4：

Figure D-4 Software Setup Interface

4． Set FTP server IP address, user name, password, Update software name, click Apply button, record update software ID；

5． Wait for upgrade software, Update successful；

6．

Click on navigation bar to check version; set updated software ID as startup version; as FigureD-5：

Figure D-4 Display Software Version Dialog Bo

7．

Click Restart under equipment management in navigation bar; as Figure D-6：

-71-

SICOM3024 工业以太网交换机用户手册

Figure D-5 Software Restart

8．

Wait for 30 seconds，start Web management system; click on navigation bar to check equipment basic information; software version; sure about the update successfully. As Figure D-7：

Update is Finished.

Figure D-6 Equipment Informatio

-72-

SICOM3024 Industrial Ethernet Switch User`s Manual

SICOM3024 Industrial Ethernet Switch

User’s Manual

SICOM3024 Industrial Ethernet Switch

User’s Manual

Preface

Notice for Safety Operation

Explanation of Warning Marks:

Warning: pay special attention to the notes behind the mark, improper operation will result in serious damage of the switch or injury of operation personnel.

Caution, attention, warning, danger: remind the positions requiring attention during operation.

Contents

Chapter 1 System Overview

1.1 Product Overview

1.2 System Features

1.3 Packing list and unpacking check

第二章 Performance Specifications

2.1 System Specifications

2.2 Service Interface

2.3 Service Function

第三章 Hardware Structure

3.1 System Structure

3.1.1 Case

3.1.2 Front Panel

LED Indicators

3.2 Interface Description

3.2.1 Gigabit Optical Fiber interface

3.2.2 Optical Fiber interface

3.2.3 RJ45 interface

LED indicators

Power input terminal

AC Power input terminal：

RS232 Network management interface（CONSOLE）

第四章 Hardware installation

4.1 Installation requirement

4.2 Mainframe installation

4.2.1 Stable rack mounting

4.3 Cable connecting

4.4 Optical Fiber Connection

4.5 Cable wiring

Attention:

第五章 Test methods

5.1 Self inspection

5.2 TP Port Test

PC1 PC2

5.3 Fiber Port Test

PING commands example：

第六章 Networking Method

6.1 Networking

6.2 System configure

第七章 WEB Management Software

7.1 Login Web service

7.2 Equipment State Display

7.2.1 Basic information

7.2.2 Port State

7.2.3 Port Flow

7.3 Equipment basic configuration

7.3.1 IP address configuration

7.3.2 Equipment name configuration

7.3.3 Port configuration

7.3.4 Password change

7.3.5 Software edition query

7.3.6 Software update

7.4 Advanced Configuration

7.4.1 Port Traffic Control

7.4.2 VLAN Configuration

Attention：Default

7.4.3 Port Mirroring Configuration

7.4.4 Port Aggregation Configuration

Attention：

7.4.5 Redundant Ring Configuration

Attention：The ID number in one redundant ring must be same.

Redundant Ring network support DT-Ring Protocol.

7.4.6 Port Priority Setting

Attention：SICOM3024 support 2 priority level

7.4.7 Other Configuration

7.4.8 SNMP Configuration

7.4.9 IGMP-SNOOPING

7.4.10 ACL list control

7.5 Device Management

第八章 CLI Command