BMC Teammachine SLR User Manual

TEAMMACHINE

SLR01

User

M

anual for Teammachine

SLR 01, ICS Carbon Cockpit and ICS2 Stem

Assembly I nstructions T eammachine SLR 01

7

8

5

6

3

4

1

2

9

10

11

General N ote and S ymbols

Overview of G rease and T hread L ocker

Seatpost C lamp & C over

Stem A ssembly P reparation

Steerer L ength and S teerer C utting I nstructions ( ICS 2 and C arbon C ockpit)

Brake A ssembly

Shimano D i2 A ssembly I nstructions

Fork I nstallation and C able R outing

I CS C arbon C ockpit I nstallation

I CS 2 S tem I nstallation

Spare P arts

General

Note

The assembly instructions are intended to support dealers and/or customers during the build of Teammachine SLR01 framesets.

• The user must be familiar with the methods used to build a bicycle.

• The user is knowledgeable on how to assemble the latest parts and components.

• The user can handle the tools needed for the proper assembly.

• The user is aware that the frames and parts are sensitive products, and he treats them with care.

Symbols

These symbols are used in the assembly instructions and indicate the appropriate actions, described below.

Grease Torque Setting Thread locker

Overview of Grease and Thread Locker

Apply grease on the contact surface between the seatpost wedge and the frame.

Do not apply grease on the contact surface between the seatpost clamp and seatpost wedge.

Seatpost Clamp and

Seatpost Installation

Seatpost Clamp Installation

•

•

•

Apply grease on the contact surface between wedge and frame.

Install the clamp wedge onto the frame.

Do not apply grease between the seatpost clamp and the seatpost!

DO NOT APPLY GREASE

BETWEEN THE

SEATPOST CLAMP AND

THE SEATPOST!

Seatpost Clamp Cover

There are two different covers for the seatpost clamp:

•

Size 48 and 51

•

Size 54 to 61

The indentation will help you making sure you are using the correct one.

The seatpost clamp cover can be inserted by pressing it into the clamp, no tools required.

•

•

•

Seatpost Installation

Apply carbon friction paste onto the seatpost. Do not apply grease.

Insert the seatpost into the frame.

Tighten the seatpost clamp to a range from 5-7 Nm.

•

•

•

Shimano Di2 Battery Installation

Install the Shimano Di2 battery into the seatpost using the adapter supplied.

Insert the battery into the adapter.

Thread the adapter into the seatpost, the foam will keep it securely in place.

Derailleur Hangers

Rear Derailleur Hangers

Shimano and SRAM rear derailleur (RD) hangers are available for the

Teammachine SLR01.

Apply grease to the RD hanger’s contact surface, before the installation.

Hand-tighten the bolt or tighten it to 2Nm, if using a torque wrench.

SRAM

Shimano

SRAM

Shimano

Stem Assembly

Preparation

Fork, Headset and Stem Pre-tensioning

•

Apply grease to the lower bearing seat on the frame and on the fork crown, then position the lower bearing on it.

• Apply grease on the upper bearing seat on the frame and then position the upper bearing on it.

• Install the fork into the headtube.

• Install the circlip onto the upper bearing.

• Install the fork onto the frame.

Topcone, Spacers and Stem/Cockpit configuration

Select the desired topcone/spacer configuration, choosing between:

• Low topcone or high topcone

• Spacers (10mm or 3mm)

• Assemble the components on the frame.

• Make sure the spacers are aligned with the topcone.

• The two halves of the spacers must be correctly aligned and engage with a click.

See details below.

3

1.

High or low topcone

2.

Spacers

3.

ICS2 Stem or ICS Carbon Cockpit

Top View concave face

• The two halves of the spacers are not identical!

Ensure the concave face is facing up and the convex face is facing down.

• Spacers are locked by applying pressure.

Spacers can be connected only when aligned correctly.

Bottom View convex face

2

1

Topcap Options

• The open topcap can be used on ICS Carbon and ICS2 to add standard round spacers above the stem.

• This allows the finetuning of the riding position before cutting the steerer to its final length.

• Consult the next page to check the detailed assembly and ensure you are using the correct parts.

• All parts are included in the delivery of the complete bikes, modules and stems/cockpits parts.

Closed Top c ap

ICS

Carbon

ICS

2

Open Top c ap

Closed Top c ap

Open Top c ap

ICS

Carbon

3

2

1

4

8

7

5

6

Closed Topcap

1. Bolt

2. Flush Topcap

3. Steerer Wedge

Open Topcap

4. Compression Bolt

5. Round Topcap

6. Standard Spacer

7. Lipped Steerer Wedge for Round Spacers

8. Shaped Top Cap for Round Spacers

ICS 2

2

1

3

6

4

5

Closed Topcap

1. Compression Bolt

2. Flush Topcap

Open Topcap

3. Compression Bolt

4. Round Topcap

5. Standard Spacer

6. Lipped Steerer Wedge for Round Spacers

Steerer Cutting

Instructions

(ICS Carbon Cockpit and ICS2 Stem)

• Compress the assembled parts by hand and make sure that the topcone, spacers and stem are aligned properly.

• This procedure is identical for both ICS2 and ICS Carbon, the illustration below displays the procedure on the ICS Carbon cockpit.

• For the closed topcap configuration, mark the topcap contact surface level on the steerer.

• The example below demarcates the contact surface area for the closed topcap configuration on ICS carbon.

Closed topcap configuration

Shaped topcap contact surface

• For the open topcap configuration, mark the steerer at the contact level above the top round spacer

• The example below demarcates the contact surface area using a spacer on the stem.

Closed topcap configuration

Shaped Topcap contact surface

Fork Steerer Cutting Mark

Once the height of the topcap contact point has been marked on the steerer (see previous instructions) you can proceed to mark the steerer a second time.

The second mark is used to cut the steerer.

Note that the cutting mark is different with ICS2 and ICS Carbon.

• ICS Carbon: the steerer is cut 4mm below the topcap contact surface.

• ICS2: the steerer is cut 3mm below the topcap contact surface.

ICS Carbon : 4mm

ICS2 : 3mm

• Proceed to cut the steerer. To ensure a precise cut, use a fork-cutting jig and a vice.

•

Deburr the steerer with fine grain sandpaper.

• After the steerer has been cut, the self-cutting bolt can be installed until it is level with the surface.

• Grease the self-cutting bolt for easier installation.

•

Remove any excess material from the bolt installation.

Check Headset Operability

• Install the fork, the headset, the stem and the topcap onto the frame to check the headset functionality:

ü The headset must have no play

•

ü

The headset torque can be easily adjusted

ü The stem does not compress the fork steerer when tightened •

If the steerer has not been cut correctly (i.e. it’s too long for the chosen configuration), the topcap might be interfering with the steerer, not allowing the headset to be compressed.

Shorten the steerer accordingly

Ensure a gap of 1mm between the steerer and the topcap after the topcap has been installed!

Brake Assembly

Rear Brake Assembly

• Install the rear brake caliper onto the frame.

• The brake line enters the frame at the chainstay.

• Inside the frame, the brake line is threaded over the BB cartridge.

• The brake hose exits at the top of the headtube.

• A foam tube must be installed over the brake line in the downtube. Slide it over when the hose exits the headtube.

Front Brake Assembly

• Attach the front brake to the adapter.

• Tighten it according to manufacturer’s instructions.

• Make sure the brake mount is in the correct position.

• The “UP” mark must face up and out, as shown in the illustration below.

UP

• Guide the brake hose into the fork.

• Attach the front brake to the fork.

Standard Style Brake-Assembly for ICS2

The front brake hose runs along the left side of the steerer tube.

UK Style Brake-Assembly for ICS2 and Standard Brake-Assembly for ICS

Carbon

For UK style brake-assembly and for ICS Carbon, the front brake hose runs along the right side of the steerer tube.

This is because the cables cross to the opposite side inside the ICS Carbon cockpit.

Shimano Di2

Assembly Instructions

Shimano Di2 Groupset Assembly

• Prepare the DTi downtube cover and Shimano EW-

RS910 (Shimano Di2 Junction Box) for installation on the down tube.

• These parts will only be assembled after the Di2 wires are routed through the frame.

Shimano Di2 Cable Routing:

1.

1x Shimano Di2 Battery (Shimano BT-DN110-A-1)

2.

1x Shimano Di2 Junction A (Shimano EW-RS910)

•

•

3.

2 x Shimano Di2 Junction B (Shimano SM-JC41)

•

1 X Shimano EW-SD50 Di2 cable, 700mm (from SM-JC41 to Rear Derailleur)

• 1 X Shimano EW-SD50 Di2 cable, 1000mm (from SM-JC41 to Battery)

•

1 X Shimano EW-SD50 Di2 cable, 350mm (from SM-JC41 to Front Derailleur)

• 1 X Shimano EW-SD50 Di2 cable, 700mm (from SM-JC41 to EW-RS910)

1 X Shimano EW-SD50 Di2 cable, 150mm (from EW-RS910 to SM-JC41)

2 X Shimano EW-SD50 Di2 cable, 1000mm (from Handlebar to SM-JC41)

TIP

Use Shimano EW-SD50-I cable ties on every Di2 cable to improve the cable stability inside the frame

1

3

2

TIP

Cover Di2 junctions with foam padding to avoid noise.

Derailleurs and Cranks

Install front/rear derailleurs and cranks according to Shimano instructions.

Shimano Di2 Battery Installation

Install the Shimano Di2 battery into the seatpost using the adapter supplied.

Insert the battery into the adapter.

Thread the adapter into the seatpost. The foam will keep it in place.

SRAM RED eTAP and eTAP AXS

For SRAM eTap and eTAP AXS, no electric wires need to be installed in the frame.

The assembly of the brake lines is similar to the assembly of the Shimano brakes.

Install the DT-Cover on the cable exit of the downtube.

Install SRAM AXS components according to SRAM instructions.

Fork Installation and

Cable Routing

ICS Carbon and ICS2

Fork Installation

• Install the lower headset bearing into the fork and slide it through the frame.

• Make sure the rear brake hose runs along the right side of the fork steerer according to standard ICS2 assembly.

• It is recommended to use electric tape to prevent the brake hose from moving inside the headtube.

• For countries with inverted brakes (e.g. UK) and for ICS Carbon, the rear brake hose runs along the left side of the steerer tube. Check the diagram on the next page for details.

• Install the upper headset bearing and the cone.

• The bearings need to be greased!

ICS Carbon Cable Routing

1

ICS Carbon Standard Assembly

1.

Rear Brake Routing

2.

Front Brake Routing

3.

Shimano Di2 Cables

ICS Carbon Inversed Assembly (UK)

1.

Front Brake Routing

2.

Rear Brake Routing

3.

Shimano Di2 Cables

2

1

2

ICS Carbon Standard Assembly

1.

Rear Brake Routing

2.

Front Brake Routing

3.

Shimano Di2 Cables

ICS Carbon Inversed Assembly (UK)

1.

Front Brake Routing

2.

Rear Brake Routing

3.

Shimano Di2 Cables

ICS2 cable routing

1

2

3

ICS2 Standard Assembly

1.

Rear Brake Routing

2.

Front Brake Routing

3.

Shimano Di2 Cables

ICS2 Inversed Assembly (e.g. UK)

1.

Front Brake Routing

2.

Rear Brake Routing

3.

Shimano Di2 Cables

ICS2 Standard Assembly

1.

Rear Brake Routing

2.

Front Brake Routing

3.

Shimano Di2 Cables

ICS Carbon

Cockpit Installation

Prepare the topcap and spacer/topcone configuration based on where the steerer has been cut.

2

1

1. High or Low Topcone

2. Spacers

Install the topcap and spacer/topcone configuration you have selected.

Install the open topcap to maintain a longer steerer tube and be able to still adjust the riding position if needed.

Install the closed topcap for the cleanest look if you know your stack height.

Important Note:

Make sure the correct steerer wedges are installed before installing the topcaps.

Closed Topcap Open Topcap

Slide the topcone over the fork steerer and hoses.

• Install the spacers.

• The two halves of the spacers must connect properly and engage with a click.

•

The two halves of the spacers are not identical!

Ensure the concave face is facing up and the convex face is facing down.

• Spacers are locked by applying pressure.

Spacers can be connected only when oriented correctly.

Run the cables through the cockpit, using the cable liners supplied, or another tool for internal cable routing.

Please refer to the video manual for more specific instructions.

Install the Steerer Wedges

• Make sure you are using the correct wedge, either for open or closed topcap configuration (see below).

• Make sure the wedges are aligned correctly (illustration on the right).

Closed Topcap Open Topcap

Install the Topcap for the Selected Configuration

• Closed (flush)

• Open (with round spacers over the stem)

Closed Topcap Open Topcap

• Alternate whilst tightening the retention bolts for even torque distribution.

•

Apply 3 Nm of torque

• Install the bolt cover

3

2

1

ICS2

Stem Installation

Slide the topcone over the fork steerer and hoses.

• Install the spacers.

• The two halves of the spacers must connect properly and engage with a click.

• The two halves of the spacers are not identical!

Ensure the concave face is facing up and the convex one is facing down

• Spacers are locked applying pressure

Spacers can be connected only when correctly oriented

Install the cable guide.

Make sure the brake lines do not get squeezed between the spacers, cable guide or stem. This could damage the brake lines.

Install the stem body Make sure only the upper stem bolt is installed onto the stem body at this point.

Install the topcap and spacer/topcone configuration you have selected.

Install the open topcap to maintain a longer steerer tube and be able to still adjust the riding position if needed.

Install the closed topcap for the cleanest look if you know your stack height.

Important Note:

Make sure the correct steerer wedges are installed before installing the topcaps.

Closed Topcap

Open Topcap

Install the topcap and adjust the headset play free.

Install the lower stem bolt and tighten both bolts to 5 Nm.

•

Attach the cable to the stem using the cable clip.

Tighten to 2Nm

•

Install the cover

Tighten to 2Nm

Connect the brake hoses with the levers and proceed with a brake bleed according to the manufacturer’s guidelines.

Attention:

Make sure to keep an even alignment of the handlebar and stem with the fork.

Never rotate the handlebar and stem in relation to the fork!

This damages the internal brake hoses.

Computer Mounts

ICS2

• The alloy computer mount is compatible with ICS01 and ICS2 stems and features Garmin and Wahoo inserts.

• Single and double mounts are available, allowing the installation of additional devices that use the GoPro interface.

• The alloy brackets (Nr.1&2) are installed between the stem faceplate and the handlebar, as shown below.

ICS2

3

1. Single Mount

2. Double Mount

2 1

3. Alloy Computer Mount

(Garmin and Wahoo inserts)

Correct Installation of the Alloy Bracket

ICS Carbon

• The alloy computer mount features Garmin and Wahoo inserts, allowing the installation of additional devices that use the GoPro interface.

• The computer mount can be adjusted to adapt to different device sizes.

•

Note: The washers must be positioned between the bolt and the computer mount.

• Tighten to 2.5 Nm.

ICS Carbon

1

2

1. Alloy Computer Mount

Garmin and Wahoo inserts)

2. Go-Pro Low Mount (available in the aftermarket)

Spare parts

TEAMMACHINE SLR 01

9

10

11

12

6

7

8

2

3

4

Pos. N° Part N°

1 30000704

5

30000699

30000714

30000705

30000698

30000700

30000701

30000702

212500

30000742

30000741

30000743

Part Name

HS-B-13

Axle Kit #7 Stealth

BRK MOUNT ADP SLR01/SLR

Cable Guide #26

Aero Cage Set

Description

Headset, w/o top cone →ICS2 stem for 160mm rotor

Dropout # 71

Dropout # 72

SP CMP # 26

Standard (Shimano/Sram/Campa)

Direct mount (Shimano only) incl. Both cover for all frame sizes

Internal battery adapter

SP SLR01 SLR 15mm offset 400mm standard part

SP SLR01 SLR 0mm offset 400mm fitting part

SP SLR01 SLR 30mm offset 400mm fitting part

TEAMMACHINE SLR

13

14

10

11

12

6

8

9

10

3

4

5

Pos. N° Part N°

1 213682

2 30000811

30000704

30000699

30000714

30000713

30000700

30000701

212500

219532

30000702

30000742

30000741

30000743

Part Name

Expander # 2

TC Set RSTR

HS-B-13

Axle Kit #7 Stealth

BRK MOUNT ADP SLR01/SLR

Description

Headset w/o top cone

Cable guide #27

Dropout # 71

Dropout # 72

Internal battery adapter for mechanical, Di2 and wireless

Standard (Shimano/Sram/Campa)

Direct mount (Shimano only) for S/P with foam core

Battery adapter, compliance post for S/P without foam core

SP CMP # 26 incl. Both cover for all frame sizes

SP SLR01/SLR, 15mm offset,

400mm

SP SLR01/SLR, 0mm offset,

400mm

SP SLR01/SLR, 30mm offset,

400mm stealth stealth

Stealth

ICS CARBON

Pos. N°

2 to 10

15, 16

11 (2x), 12 (3x), 13, 14

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

1 to 4, 7 to 10

Part N°

30000723

Part Name

TC Set ICS2 ICS CBN RED

30000726 CKP ICS Carbon 90 400 RED

Description

30000709 CKP ICS Carbon Small part kit RED including self cutting bolt

30000720 COM ICS CBN for Garmin & Wahoo, incl GO PRO

Mount red top cones and spacers

30000727 CKP ICS Carbon 100 420 RED

30000728 CKP ICS Carbon 110 420 RED

30000729 CKP ICS Carbon 120 420 RED

CKP ICS Carbon 110 400 RED

30000730 TEAM

30000731

30000732

30000733

CKP ICS Carbon 120 400 RED

TEAM

CKP ICS Carbon 130 400 RED

TEAM

CKP ICS Carbon 140 400 RED

TEAM w/o open top cap and wedge w/o spacers or top cones w/o computer mount

Drop Reach

127

127

127

127

127

127

127

127

77

77

77

67

67

67

67

77

ICS 2

Pos. N°

1 to 12, 13 (1x), 14 (3x)

1 to 12, 13 (1x), 14 (3x)

1 to 12, 13 (1x), 14 (3x)

1 to 12, 13 (1x), 14 (3x)

1 to 12, 13 (1x), 14 (3x)

1 to 12, 13 (1x), 14 (3x)

Part N°

30000734

30000735

30000736

30000737

Part Name

ST ICS2 80mm

ST ICS2 90mm

ST ICS2 100mm

ST ICS2 110mm

30000738 ST ICS2 120mm

30000739 ST ICS2 130mm

Description

Top cone not included

Top cone not included

Top cone not included

Top cone not included

Top cone not included

Top cone not included

1 to 12, 13 (1x), 14 (3x) 30000740 ST ICS2 140mm

2 to 12

13 (2x), 14 (3x), 15,16

15,16

15,16

17, 18, 19

19

30000708

30000724

30000722

30000725

ICS 2 Small part kit

TC Set ICS2 ICS CBN BLK

TC Retrofit Set ICS2 ICS CBN BLK

Top cone not included

Cover for all stem length included

ICS2 stem → ICS2 frame*

TC Retrofit Set ICS1 ICS AERO BLK ICS1 stem → ICS2 frame

30000718 ICS1/2 - computer mount

302189 ICS01 Garmin Mount Long Alloy

ICS2 stem → ICS1 frame**

Aluminium

20

20

301707006919 Handlebar RCB01

301707006920 Handlebar RCB01

20 301707006921 Handlebar RCB01

*ICS2 frames: Teammachine SLR01, SLR, MY21

400mm, stealth

420mm, stealth, ca. 193g

440mm, stealth

**ICS1 frames: Teammachine SLR01/ SLR02 MY18-20; Roadmachine >MY20; UnReStricted URS

Roadmachine MY17-19 and Timemachine Road are not compatible

-12.5°

-12.5°

-12.5°

-12.5°

Angle

-12.5°

Drop Reach

-12.5°

-12.5°

117mm 77mm

117mm 77mm

117mm 77mm

ICS Compatibility

ICS Frames

TEAMMACHINE SLR01

[MY21 à ]

ROADMACHINE 01 & URS 01

[MY20 à ]

TEAMMACHINE SLR 01

[MY18/19/20]

ALPENCHALLENGE AMP CARBON

[MY19 à ]

TIMEMACHINE 01 Road

[MY19 à ]

ROADMACHINE 01

[MY17/18/19]

ICS COMPATIBILITY CHART

ICS Configurations

®

ICS2 / ICS Carbon

®

ICS01 / ICS01 0°

®

ICS Aero

Parts Needed

ICS Carbon & ICS2

(MY21 SLR01)

Topcones marked as

#1 (5mm) or #2 (30mm) art. 30000723 (RED)

TC Set ICS2 ICS CBN RED art. 30000724

TC Set ICS2 ICS CBN BLK

ICS Carbon & ICS2

(Retrofit)

Topcones marked as

#3 (5mm) or #4 (30mm) art. 30000722

TC Retrofit Set ICS2 ICS CBN

BLK

ICS01 & ICS Aero

(Retrofit for MY21 SLR01) art. 30000725

TC Retrofit Set ICS1 ICS AERO

BLK

Topcones marked as

#5 (5mm) or #6 (30mm)

ICS01/ICS01 0

°

& ICS Aero

(Retrofit for other Platforms)

Low topcones are standard in complete bike builds and modules. Additional topcones are available for customization.

art. 302084

Topcone ICS high 32 mm

(MY20 à RM/URS, MY19 à AC

AMP CARBON, MY18/19/20

SLR01) art. 300712 / 300713

MY17/18/19 Roadmachine 01 topcone (38mm High/18mm

Low) art. 300717 / 300718

MY17/18/19 Roadmachine 02 topcone (38mm High/18mm

Low) art. 301705 / 301706

MY19

à

Timemachine 01 Road topcone (27mm High/12mm

Low)

TOPCONE IDENTIFICATION

The topcones designed for MY21, Teammachine SLR01 frames, for the retrofitting of ICS Carbon cockpits and ICS2 stems, feature clear indentations for easy identification and compatibility check.

Topcone ICS2, ICS

Carbon

– MY21 Teammachine SLR01

Topcones that feature #1 and #2 indentations (available in red or black) are designed to fit ICS2 stems and ICS Carbon cockpits on MY21 Teammachine SLR01 frames.

Topcone ICS2,

ICS

Carbon - Retrofit

Topcones that feature #3 and #4 indentations (only available in black) are designed to retrofit ICS2 stems and ICS Carbon cockpits on the following platforms:

• TEAMMACHINE SLR01: MY18 à MY20

• ROADMACHINE 01: MY20 à

• URS 01: MY20 à

• ALPENCHALLENGE AMP CARBON: MY19 à

Topcone ICS01 / ICS Aero – MY21 Teammachine SLR01

#5 and #6 topcones (only available in black) can be used to fit ICS Aero, ICS01 and ICS01 0° stems and the MY21 TEAMMACHINE SLR01.

Notes

• An additional topcone, marked as #7 allows the installation of round-steerer forks on MY21 Teammachine SLR frames.

• Timemachine 01 Road is currently not compatible with ICS2 and ICS Carbon.

TOPCONE MARKING INDEX

Part Identification

#1 ICS2-CARBON 5mm

#2 ICS2-CARBON 30mm

#3 ICS2-CARBON 5mm

#4 ICS2-CARBON 30mm

#5 ICS1-AERO 5mm

#6 ICS1-AERO 30mm

#7 ROUND 8mm

Part Description

Topcone ICS2, ICS Carbon, Low 5mm (MY21 SLR01)

Topcone ICS2, ICS Carbon, High 30mm (MY21 SLR01)

Topcone ICS2, ICS Carbon, Low 5mm (Retrofit)

Topcone ICS2, ICS Carbon, High 30mm (Retrofit)

Topcone ICS01 / ICS Aero, Low 5mm (MY21 Teammachine SLR)

Compatibility

• MY21 TEAMMACHINE SLR01 ONE

•

MY21 TEAMMACHINE SLR01 TWO

• MY21 TEAMMACHINE SLR01 ICS CARBON

MODULES

• MY21 TEAMMACHINE SLR01 ONE

• MY21 TEAMMACHINE SLR01 TWO

•

MY21 TEAMMACHINE SLR01 ICS CARBON

MODULES

• ROADMACHINE 01 MY20

®

• URS 01 MY20

®

• ALPENCHALLENGE AMP CARBON MY19

®

• TEAMMACHINE SLR01 MY18

®

20

• ROADMACHINE 01 MY20

®

• URS 01 MY20

®

• ALPENCHALLENGE AMP CARBON MY19

®

• TEAMMACHINE SLR01 MY18

®

20

•

MY21 TEAMMACHINE SLR01

Topcone ICS01 / ICS Aero, High 30mm (MY21 Teammachine SLR)

• MY21 TEAMMACHINE SLR01

Topcone Round Steerer, 8mm (MY21 Teammachine SLR) • MY21 TEAMMACHINE SLR