www.teknikoffice.co.uk

Teknik

Sit and surf .

Steel Gorge Desk Milled Mesquite

Model

5

425907

Table of Contents

Part Identifi cation

Hardware Identifi cation

Assembly Steps

Français

Español

Safety

Warranty

3

4

5-28

29-32

33-36

37-38

39

Assembly Tools Required

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

Page 2

Part Identifi cation

Now you know our ABCs.

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.

A RIGHT LEG (1)

B LEFT LEG (1)

C CENTER LEG (1)

D TOP (1)

E RIGHT END (1)

F CENTER END (1)

G CENTER UPRIGHT (1)

H LEFT UPRIGHT (1)

I BACK (1)

J LARGE BACK (1)

K SHELF (1)

L LARGE EXTENSION BLOCK (2)

M SMALL EXTENSION BLOCK (2)

N BRACE (1)

O LONG BRACE (2)

P SHORT BRACE (2)

Q LARGE DRAWER RIGHT SIDE (1)

R LARGE DRAWER LEFT SIDE (1)

S LARGE DRAWER BACK (1)

T LARGE DRAWER BOTTOM (1)

U DRAWER RIGHT SIDE (1)

V DRAWER LEFT SIDE (1)

W DRAWER BACK (1)

X DRAWER BOTTOM (1)

Y DRAWER BRACE (1)

Z DRAWER FRONT (1)

AA LARGE DRAWER FRONT (1)

O

O

H

W

I

M

V

N

B

X

D

U

G

Z

M

F

J

C

K

S

T

P

Q

L

E

AA

R

P

L

Y

A

Page 3

Hardware Identifi cation

å Screws are shown actual size. You may receive extra hardware with your unit.

(EXTENSION SET SHOWN SEPARATED)

1 LEFT RAIL - 1 2 RIGHT RAIL - 1 3 EXTENSION RAIL - 2 4 EXTENSION SLIDE - 2

5 HIDDEN CAM - 12 6

SMALL HIDDEN

CAM - 12

7 CAM SCREW - 24 8 WOOD DOWEL - 4

9 METAL BRACKET - 6 10 KNOB SET - 2 11 NUT - 1 12 TOOL - 1 22

BUMPER

CARD - 1

Page 4

13 BLACK 1-3/4" PAN HEAD SCREW - 10

15 BLACK 1" FLAT HEAD SCREW - 8

23 BLACK 1" MACHINE SCREW - 2

19 BLACK 1/2" FLAT HEAD SCREW - 12

21 BLACK 5/16" MACHINE SCREW - 1

14 BLACK 1" PAN HEAD SCREW - 4

16 BLACK 11/16" FLAT HEAD SCREW - 4

18 BLACK 1/2" PAN HEAD SCREW - 22

20 BLACK 1/2" MACHINE SCREW - 4

Step 1

å

Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor.

å

Fasten the LEFT LEG (B) to the LEFT UPRIGHT (H). Use two BLACK 1-3/4" PAN HEAD SCREWS (13) and two

BLACK 1/2" PAN HEAD SCREWS (18).

13

BLACK 1-3/4" PAN HEAD SCREW

(2 used in this step)

B

Surface with holes

Edge with holes

H

Holes facing up

18

BLACK 1/2" PAN HEAD SCREW

(2 used in this step)

Page 5

Step 2

å

Fasten the LEFT RAIL (1) and one of the SMALL

EXTENSION BLOCKS (M) to the LEFT UPRIGHT (H) exactly as shown. Use two BLACK 11/16" FLAT

HEAD SCREWS (16).

å

NOTE: Find the back hole fi rst. Then, slide the inner cartridge of the LEFT RAIL in to fi nd the other hole that lines up with the hole in the SMALL EXTENSION BLOCK and LEFT UPRIGHT. Turn a SCREW into this hole.

å

NOTE: You should start each SCREW a few turns before completely tightening any of them.

16

BLACK 11/16" FLAT HEAD SCREW

(2 used in this step)

Holes facing up

These edges should be even.

H

1

M

Line up the back hole fi rst.

Finished surface

1

This hole is closer to this edge.

Page 6

Step 3

å

Fasten four METAL BRACKETS (9) to the CENTER

LEG (C) exactly as shown. Use four BLACK 1/2" PAN

HEAD SCREWS (18).

9

C

18

BLACK 1/2" PAN HEAD SCREW

(4 used in this step)

Page 7

Step 4

å

Fasten the CENTER LEG (C) to the CENTER END (F) and

CENTER UPRIGHT (G). Use four BLACK 1/2" PAN HEAD

SCREWS (18) through the METAL BRACKETS on the CENTER

LEG and into the CENTER END and CENTER UPRIGHT.

å

Finish fastening the CENTER LEG (C) to the CENTER END (F) and CENTER UPRIGHT (G). Use four BLACK 1-3/4" PAN

HEAD SCREWS (13).

å

Turn two CAM SCREWS (7) into the CENTER END (F).

18

BLACK 1/2" PAN HEAD SCREW

(4 used in this step)

C

Surface with fewer holes

G

Edge without holes

Sur

F

face with holes

7

13

BLACK 1-3/4" PAN HEAD SCREW

(4 used in this step)

Page 8

Step 5

å

Fasten one of the LARGE EXTENSION BLOCKS (L) to the

CENTER END (F). Use two BLACK 1" PAN HEAD SCREWS (14) in the outer holes.

BLACK 1" PAN HEAD SCREW

(2 used in this step)

14

This hole is closer to this edge.

C

Surface with more holes

L

F

Page 9

Step 6

å

Carefully fl ip the CENTER LEG (C) over.

å

Fasten the RIGHT RAIL (2) and the remaining SMALL

EXTENSION BLOCK (M) to the CENTER UPRIGHT (G) exactly as shown. Use two BLACK 11/16" FLAT HEAD SCREWS (16).

å

NOTE: Find the back hole fi rst. Then, slide the inner cartridge of the RIGHT RAIL in to fi nd the other hole that lines up with the hole in the SMALL EXTENSION BLOCK and CENTER

UPRIGHT. Turn a SCREW into this hole.

16

BLACK 11/16" FLAT HEAD SCREW

(2 used in this step)

2

These edges should be even.

G

Line up the back hole fi rst.

2

M

Finished surface

C This hole is closer to this edge.

Page 10

Step 7

å

Fasten two METAL BRACKETS (9) to the RIGHT

LEG (A) exactly as shown. Use two BLACK 1/2" PAN

HEAD SCREWS (18).

18

BLACK 1/2" PAN HEAD SCREW

(2 used in this step)

A

9

Page 11

Step 8

å

Fasten the RIGHT LEG (A) to the RIGHT END (E). Use two

BLACK 1/2" PAN HEAD SCREWS (18) through the METAL

BRACKETS on the RIGHT LEG and into the RIGHT END.

å

Finish fastening the RIGHT LEG (A) to the RIGHT END (E).

Use two BLACK 1-3/4" PAN HEAD SCREWS (13).

18

BLACK 1/2" PAN HEAD SCREW

(2 used in this step)

Page 12

A

13

BLACK 1-3/4" PAN HEAD SCREW

(2 used in this step)

E

face

Sur with holes

Edge without holes

Step 9

å

Fasten the remaining LARGE EXTENSION BLOCK (L) to the RIGHT END (E). Use two BLACK 1" PAN HEAD

SCREWS (14) in the outer holes.

BLACK 1" PAN HEAD SCREW

(2 used in this step)

14

A

E

Surface with more holes

L

This hole is closer to this edge.

Page 13

Step 10

å

Separate the EXTENSION SLIDES (4) from the EXTENSION RAILS (3) as shown in the enlarged diagram below. Be prepared, the parts are greasy.

å

Fasten the EXTENSION RAILS (3) to the LARGE EXTENSION BLOCKS (L).

Use four BLACK 1/2" FLAT HEAD SCREWS (19).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the back hole. Then, slide the inner cartridge of the EXTENSION RAIL in to fi nd the other hole that lines up with the hole in the LARGE EXTENSION BLOCK. Turn a SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the LARGE DRAWER.

3 4

Push up on the black lever and pull the SLIDE from the RAIL.

19

BLACK 1/2" FLAT HEAD SCREW

(4 used in this step)

3

Use these holes.

3

L

G

Back hole

C

Open end

A

3

L

Open end

Back hole

Open end

Page 14

Step 11

å

Separate the BLACK 1/2" MACHINE SCREWS (17 and 20). Use the thicker SCREW (20) in this step.

å

Turn two CAM SCREWS (7) into the RIGHT END (E).

å

Insert two SMALL HIDDEN CAMS (6) into the LARGE BACK (J).

å

Fasten the LARGE BACK (J) to the RIGHT END (E). Tighten two

HIDDEN CAMS.

å

Fasten the SHORT BRACES (P) to the RIGHT LEG (A). Use two

BLACK 1/2" MACHINE SCREWS (20).

1

6

The arrow must point toward the edge of the board.

2

3

7

Sur face with holes

J

6

These edges should be even.

E

These edges should be even.

P

Surface without holes

P

A

Surface without holes

20

BLACK 1/2" MACHINE SCREW

(2 used for the SHORT BRACES)

Page 15

Step 12

å

Insert two SMALL HIDDEN CAMS (6) into the LARGE BACK (J).

å

Fasten the CENTER END (F) to the LARGE BACK (J). Tighten two HIDDEN CAMS.

å

Fasten the CENTER LEG (C) to the SHORT BRACES (P). Use two BLACK 1/2" MACHINE SCREWS (20).

1

6

The arrow must point toward the edge of the board.

2

3

6

J

F

C

P

20

BLACK 1/2" MACHINE SCREW

(2 used for the SHORT BRACES)

P

Page 16

Step 13

å

Carefully stand your unit upright.

å

Turn four CAM SCREWS (7) into the SHELF (K).

å

Insert four HIDDEN CAMS (5) into the ENDS (E and F).

å

Fasten the SHELF (K) to the ENDS (E and F). Tighten four

HIDDEN CAMS.

1 2

5

The arrow must point toward the edge of the board.

3

7

You may need to loosen these SCREWS to position the SHELF in place.

K

Sur face with holes

5

F

E

5

K

Page 17

Step 14

å

Turn two CAM SCREWS (7) into the LEFT UPRIGHT (H).

å

Insert two HIDDEN CAMS (5) into the BACK (I).

å

Fasten the BACK (I) to the LEFT UPRIGHT (H). Tighten two HIDDEN CAMS.

å

Fasten the BRACE (N) to the LEFT LEG (B). Use two

BLACK 1/2" PAN HEAD SCREWS (18).

1 2

5

The arrow must point toward the edge of the board.

3

Surface with holes

I

5

Finished edge

N

7

H

B

18

BLACK 1/2" PAN HEAD SCREW

(2 used for the BRACE)

N

Page 18

Step 15

å

Carefully stand the LEFT LEG (B) upright.

å

Turn two CAM SCREWS (7) into the CENTER UPRIGHT (G).

å

Insert two HIDDEN CAMS (5) into the BACK (I).

å

Fasten the BACK (I) to the CENTER UPRIGHT (G). Tighten two HIDDEN CAMS.

å

Fasten the BRACE (N) to the CENTER LEG (C). Use two

BLACK 1/2" PAN HEAD SCREWS (18).

1 2

5

The arrow must point toward the edge of the board.

3

B

7

I

5

N

C

G

18

BLACK 1/2" PAN HEAD SCREW

(2 used for the BRACE)

Page 19

Step 16

å

Turn four CAM SCREWS (7) into the TOP (D).

å

Insert four HIDDEN CAMS (5) into the UPRIGHTS (G and H).

å

Fasten the TOP (D) to the UPRIGHTS (G and H). Tighten four

HIDDEN CAMS.

å

Fasten the TOP (D) to the RIGHT LEG (A). Use two BLACK

1-3/4" PAN HEAD SCREWS (13).

1 2

5

The arrow must point toward the edge of the board.

3

7

face

Sur with holes

D

7

D

A

13

BLACK 1-3/4" PAN HEAD SCREW

(2 used for the RIGHT LEG)

G

5

H

Page 20

Step 17

å

Fasten the LONG BRACES (O) to the LEGS (B and C). Use four

BLACK 1/2" PAN HEAD SCREWS (18).

å

NOTE: Start all the SCREWS a few turns before tightening them.

å

Fasten the LONG BRACES (O) together. Use the BLACK 5/16"

MACHINE SCREW (21) and NUT (11) in the center holes in the

LONG BRACES exactly as shown.

å

NOTE: If the center holes in the LONG BRACES (O) do not line up, loosen the SCREWS in the LEGS and then retighten once the LONG BRACES are fastened together.

å

NOTE: Tighten the NUT using the TOOL (12).

18

BLACK 1/2" PAN HEAD SCREW

(4 used in this step)

C

B

21

O

11

12

21

BLACK 5/16" MACHINE SCREW

(1 used in this step)

Page 21

Step 18

å

Fasten the LARGE DRAWER SIDES (Q and R) to the

LARGE DRAWER BACK (S). Use four BLACK 1" FLAT

HEAD SCREWS (15).

å

Slide the LARGE DRAWER BOTTOM (T) into the grooves in the LARGE DRAWER SIDES (Q and R) and LARGE

DRAWER BACK (S).

å

Fasten the EXTENSION SLIDES (4) to the LARGE

DRAWER SIDES (Q and R). Use four BLACK 1/2" FLAT

HEAD SCREWS (19).

15

BLACK 1" FLAT HEAD SCREW

(4 used in this step)

R

S

S

R

Q

T

Finished sur face

Q

4

R

4

19

BLACK 1/2" FLAT HEAD SCREW

(4 used for the SLIDES)

4

Use these holes.

Page 22

Q

Groove

Step 19

å

Turn four CAM SCREWS (7) into the LARGE

DRAWER FRONT (AA).

å

Peel two BUMPERS from the BUMPER CARD (22) and stick them onto the LARGE DRAWER FRONT (AA) in the locations shown.

å

Insert four SMALL HIDDEN CAMS (6) into the LARGE

DRAWER SIDES (Q and R).

å

Fasten the LARGE DRAWER FRONT (AA) to the LARGE DRAWER

SIDES (Q and R). Tighten four HIDDEN CAMS.

å

Fasten a KNOB SET (10) to the LARGE DRAWER

FRONT (AA). Use one BLACK 1" MACHINE SCREW (23).

1

6

The arrow must point toward the edge of the board.

7

22

2

3

AA

7

Q

6

23

BLACK 1" MACHINE SCREW

(1 used for the KNOB SET)

R

10

AA

Be sure the LARGE DRAWER

BOTTOM (T) inserts into the groove in the LARGE DRAWER FRONT (AA).

Page 23

Step 20

å

Fasten the DRAWER SIDES (U and V) to the DRAWER

BACK (W). Use four BLACK 1" FLAT HEAD SCREWS (15).

å

Insert two WOOD DOWELS (8) into the holes in the

DRAWER BACK (W).

å

Push the DRAWER BRACE (Y) onto the WOOD DOWELS in the DRAWER BACK (W).

å

Slide the DRAWER BOTTOM (X) into the grooves in the

DRAWER SIDES (U and V) and DRAWER BACK (W).

8

W

V

15

BLACK 1" FLAT HEAD SCREW

(4 used in this step)

Groove

Groove

U

Y

X

Finished sur face

Page 24

Step 21

å

Turn four CAM SCREWS (7) into the DRAWER FRONT (Z).

å

Insert four SMALL HIDDEN CAMS (6) into the DRAWER

SIDES (U and V).

å

Insert two WOOD DOWELS (8) into the DRAWER BRACE (Y).

å

Fasten the DRAWER FRONT (Z) to the DRAWER SIDES (U and V). Tighten four HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWELS insert into the holes in the DRAWER FRONT.

å

Fasten a KNOB SET (10) to the DRAWER FRONT (Z).

Use one BLACK 1" MACHINE SCREW (23).

7

1

6

The arrow must point toward the edge of the board.

2

3

7

Z

8

V

6

Be sure the DRAWER

BOTTOM (X) inserts into the groove in the

DRAWER FRONT (Z).

Y

Z

X

U

23

BLACK 1" MACHINE SCREW

(1 used for the KNOB SET)

6

10

Page 25

Step 22

å

Pull the extensions of the RAILS (1 and 2) out from the

RAILS. Insert the DRAWER (Z) so it rests on the brackets of the RAILS. Line up the holes in the DRAWER SIDES (U and V) with the brackets on the RAILS.

å

Fasten the DRAWER (Z) to the RAILS (1 and 2). Use four

BLACK 1/2" FLAT HEAD SCREWS (19).

1

2

V Z

19

BLACK 1/2" FLAT HEAD SCREW

(4 used in this step)

U

Page 26

Step 23

å

To insert the LARGE DRAWER (AA) into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION

RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.

AA

Page 27

Step 24

å

NOTE: Please read the back pages of the instruction booklet for important safety information.

å

This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.

60 lbs.

30 lbs.

30 lbs.

20 lbs.

Page 28

WARNING

Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart.

Look out for:

• Overloaded shelves and drawers.

• Improper loading can cause the product to be top-heavy.

What can happen:

• Risk of injury.

• Top-heavy furniture can tip over.

• Overloaded shelves and drawers can break.

How to avoid the problem:

• Never exceed the weight limits shown in the instructions.

• Work from bottom to top when loading shelves and drawers. Place the heavier items on the lower shelves or in lower drawers.

• Improperly moving furniture that is not designed and equipped with casters.

• Placing TVs on furniture items that are not designed to support a television is hazardous.

• Furniture can tip over or break if improperly moved.

• Physical injury. Furniture can be very heavy.

• Breakage of tops - particularly with double pedestal furniture (drawers at both ends).

• Unload shelves and drawers from top to bottom before moving the unit.

• Do not push furniture, especially on a carpeted fl oor. Have a friend help you lift the item and set it in place.

• Provide support to the center section of the top when lifting the furniture.

• Risk of injury or death. TVs can be very heavy. Plus the weight and location of the picture tube tends to make TVs unbalanced and prone to tipping forward.

• This product is not designed to support a television.