Teknik 5420650 Boulevard Cafe L-Shaped Desk Instruction Booklet

www.teknikoffice.co.uk

Teknik

The original desktop .

Boulevard Cafe L-Shaped Desk

Model

5

420650

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

Table of Contents

Part Identifi cation

Hardware Identifi cation

Assembly Steps

Français

Español

Safety

Warranty

3

4-5

6-38

39-43

44-48

49-50

51

Assembly Tools Required

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

Page 2

Part Identifi cation

Now you know our ABCs.

å

While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.

A LARGE LEFT END (1)

B LARGE WIRE BACK (1)

C LONG SHELF (2)

D SHELF TUBE (3)

E SMALL TOP (1)

F BOX RIGHT END (1)

G BOX LEFT END (1)

H BOX FRONT (1)

J BOX BOTTOM (1)

K RIGHT BOTTOM (1)

L BACK(1)

M LARGE RIGHT END (1)

N SHORT RIGHT TUBE (2)

O LARGE UPRIGHT (1)

P REAR RIGHT TUBE (1)

Q SHORT BACK (1)

R SMALL WIRE BACK (1)

S SMALL LEFT END (1)

T SHORT LEFT TUBE (2)

U LEFT BOTTOM (1)

V SMALL RIGHT END (1)

W SMALL LEFT UPRIGHT (1)

X SMALL RIGHT UPRIGHT (1)

Y SHORT TUBE (2)

Z LONG BACK (1)

AA LARGE TOP (1)

BB LONG LEFT TUBE (1)

CC FRONT RIGHT TUBE (1)

DD SHELF (1)

EE DOOR (1)

FF LARGE DRAWER FRONT (1)

GG SMALL DRAWER FRONT (1)

HH DRAWER SIDE (4)

II LARGE DRAWER BACK (1)

JJ LARGE DRAWER BOX FRONT (1)

KK DRAWER BRACE (2)

LL LARGE DRAWER BOTTOM (1)

MM SMALL DRAWER BACK (1)

NN SMALL DRAWER BOX FRONT (1)

OO SMALL DRAWER BOTTOM (1)

B

A

D

D

C

C

D

Q

R

U

S

Z

V

T

T

AA

W

X

BB

II

G

Y

CC

H

P

LL

E

HH

J

F

JJ

FF

EE

O

N

DD

K

L

N

HH

KK

MM

HH

OO

HH

NN

GG

M

Page 3


å

Screws are shown actual size. You may receive extra hardware with your unit.

(EXTENSION SET SHOWN SEPARATED)

23 EXTENSION RAIL - 4 24 EXTENSION SLIDE - 4 25

LARGE HIDDEN

CAM - 2

26

SMALL HIDDEN

CAM - 15

27 CAM SCREW - 13

28

LONG CAM

SCREW - 4

29 METAL BRACKET - 7

30 WOOD DOWEL - 7 31 MAGNETIC CATCH - 1 32

MAGNETIC CATCH

SPACER - 1

33 GROMMET - 3 34 APPLIQUE CARD - 1 35 METAL PIN - 4

36 L-WRENCH - 1

Page 4


å

Screws are shown actual size. You may receive extra hardware with your unit.

37 BLACK 1-3/4" PAN HEAD SCREW - 6 38 BLACK 1-9/16" FLAT HEAD SCREW - 30

39 BLACK 1-3/8" HEX HEAD SCREW - 25 40 BLACK 7/8" HEX HEAD SCREW - 5

41 BLACK 13/16" PAN HEAD SCREW - 2

43 BLACK 5/8" FLAT HEAD SCREW - 14


47 BLACK 3/8" HEX HEAD SCREW - 19


44 BLACK 9/16" LARGE HEAD SCREW - 24

46 BLACK 1/2" FLAT HEAD SCREW - 24

Page 5

Step 1

å Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor.

å Push two LARGE HIDDEN CAMS (25) into the SMALL

RIGHT END (V).

V

25

Arrow

(2 used)

Arrow

The arrow in the HIDDEN

CAM must point toward the hole in the edge of the board.

Hole

Page 6

Step 2

å Push fi fteen SMALL HIDDEN CAMS (26) into the SMALL

LEFT END (S), BOX ENDS (F and G), BOX FRONT (H), BOX

BOTTOM (J), UPRIGHTS (X and W) and LONG BACK (Z).

26

Arrow

X

W

H

J

Arrow

Hole

The arrow in the HIDDEN

CAM must point toward the hole in the edge of the board.

S

F

Z

G

26

Arrow

(15 used)

Page 7

Step 3

å Fasten seven METAL BRACKETS (29) to the

SMALL RIGHT UPRIGHT (X), SHORT BACK (Q), and LONG BACK (Z). Use seven BLACK 5/8"

FLAT HEAD SCREWS (43).

å Turn thirteen CAM SCREWS (27) into the

SMALL TOP (E), LARGE TOP (AA), SMALL

RIGHT UPRIGHT (X), and BOX FRONT (H).

29

43

BLACK 5/8" FLAT HEAD SCREW

(7 used for METAL BRACKETS)

29

(7 used)

27

X

Z

H

Q

27

(13 used)

E

AA

Page 8

Step 4

å Turn four LONG CAM SCREWS (28) into the LARGE TOP (AA) and SHORT TUBES (Y).

Remember:

Righty tighty.

Lefty loosey.

AA

28

Y

Y

Page 9

Step 5

å Fasten the LARGE LEFT END (A) to the LARGE WIRE

BACK (B). Tighten two BLACK 1-3/8" HEX HEAD

SCREWS (39) using the L-WRENCH (36).

Page 10

39

BLACK 1-3/8" HEX HEAD SCREW

(2 used in this step)

A

36

B

Step 6

å Fasten the SHELF TUBES (D) to the LONG SHELVES (C).

Use twelve BLACK 9/16" LARGE HEAD SCREWS (44).

å NOTE: Be sure SHELF TUBES wrap around the edges of the LONG SHELVES.

44

BLACK 9/16" LARGE HEAD SCREW


Sur face with holes

D

D

Sur face with holes

C

D

C

These edges should be even.

Page 11

Step 7

å Fasten the LONG SHELF (C) with one SHELF TUBE (D) to the LARGE LEFT END (A). Tighten one BLACK 1-3/8" HEX

HEAD SCREW (39) using the L-WRENCH (36).

å Fasten the LONG SHELF (C) to the LARGE WIRE BACK (B).

Use four BLACK 9/16" LARGE HEAD SCREWS (44).

D

C

B

44



Page 12

39



A

36

Step 8

å Fasten the LONG SHELF (C) with two SHELF TUBES to the LARGE LEFT END (A). Tighten two BLACK 1-3/8" HEX

HEAD SCREWS (39) using the L-WRENCH (36).

39



A

36

C

Sur face with scr ews

Page 13

Step 9

å Fasten the FRONT RIGHT TUBE (CC) to the SMALL TOP (E).


å NOTE: Be sure the FRONT RIGHT TUBE wraps around the edge of the SMALL TOP.

å Fasten the MAGNETIC CATCH SPACER (32) and

MAGNETIC CATCH (31) to the SMALL TOP (E) exactly as shown. Use two BLACK 13/16" PAN HEAD SCREWS (41).

41

BLACK 13/16" PAN HEAD SCREW


31

32

44



CC E

Page 14

Step 10

å Fasten the BOX ENDS (F and G) to the BOX FRONT (H).

Use four BLACK 1-9/16" FLAT HEAD SCREWS (38).

å Fasten the BOX FRONT (H) and BOX ENDS (F and G) to the SMALL TOP (E). Tighten fi ve HIDDEN CAMS.

38

BLACK 1-9/16" FLAT HEAD SCREW


1

2

F

H

Surface with HIDDEN CAM

G

Surface with HIDDEN CAMS

E

H

F

G

Page 15

Step 11

å Fasten the BOX BOTTOM (J) to the BOX FRONT (H).

Tighten three HIDDEN CAMS.

1

2

H

J

Sur face with HIDDEN CAMS

Page 16

Step 12

å Fasten the BOX BOTTOM (J) to the BOX ENDS (F and G).

Use four BLACK 1-9/16" FLAT HEAD SCREWS (38).

38



J

F

G

Page 17

Step 13

å Fasten the SMALL TOP (E) to the LARGE LEFT END (A).

Tighten one BLACK 1-3/8" HEX HEAD SCREW (39) using the L-WRENCH (36).

å Fasten the SMALL TOP (E) to the LARGE WIRE BACK (B).


E

B

Page 18

39



A

36

44



Step 14

å

å NOTE: Do not completely tighten the SCREWS in this step.

Fasten the BACK (L) and RIGHT BOTTOM (K) to the

LARGE RIGHT END (M). Use fi ve BLACK 3/8" HEX HEAD

SCREWS (47) and the L-WRENCH (36).

M

K

L

47

BLACK 3/8" HEX HEAD SCREW


36

Page 19

Step 15

å

å NOTE: Do not completely tighten the SCREWS in this step.

Fasten the SHORT RIGHT TUBES (N) to the LARGE

RIGHT END (M). Use two BLACK 1-3/8" HEX HEAD


N

M

N

39



Page 20

Step 16

å Fasten the LARGE UPRIGHT (O) to the BACK (L). Tighten three BLACK 3/8" HEX HEAD SCREWS (47) with the

L-WRENCH (36).

å Fasten the LARGE UPRIGHT (O) to the RIGHT

BOTTOM (K). Use two BLACK 3/8" HEX HEAD


å Fasten the LARGE UPRIGHT (O) to the SHORT RIGHT

TUBES (N). Use two BLACK 1-3/8" HEX HEAD SCREWS

(39) and the L-WRENCH (36).

å NOTE: Now, completely tighten all of the SCREWS from

Steps 14-16.

O

39



L

N

K

N

47



36

Page 21

Step 17

å NOTE: Start all of the SCREWS before completely tightening any of them.

å Fasten the LARGE RIGHT END (M) to the SMALL TOP (E) and LONG SHELVES (C). Tighten six BLACK 1-3/8" HEX

HEAD SCREWS (39) using the L-WRENCH (36).

36

39



M

C

C

E

Page 22

Step 18

å Fasten the LARGE UPRIGHT (O) to the SMALL TOP (E).

Use three BLACK 5/8" PAN HEAD SCREWS (42).

å Fasten the REAR RIGHT TUBE (P) to the LARGE

UPRIGHT (O). Tighten one BLACK 3/8" HEX HEAD

SCREW (47) using the L-WRENCH (36).

å Fasten the REAR RIGHT TUBE (P) to the LARGE LEFT END (A).

Tighten one BLACK 1-3/8" HEX HEAD SCREW (39) using the

L-WRENCH (36).

Side Step: Make nachos. (Optional, but recommended.)

42



O

E

39



A

36

P

47



Page 23

Step 19

å

å

å

Fasten the SHORT BACK (Q) to the SMALL WIRE BACK (R). Use two BLACK 1-3/4" PAN HEAD SCREWS (37).

NOTE: Start all of the hex head SCREWS before completely tightening any of them.

Fasten the SMALL WIRE BACK (R) to the SMALL LEFT END (S). Use two BLACK 1-3/8" HEX HEAD SCREWS (39) and the L-WRENCH (36).

å Fasten the LEFT BOTTOM (U) to the SMALL LEFT END (S). Use three BLACK 3/8" HEX HEAD


å Fasten the SHORT LEFT TUBES (T) to the SMALL LEFT END (S). Use two BLACK 1-3/8" HEX HEAD SCREWS (47) and the L-WRENCH (36).

å Tighten all of the hex head SCREWS with the L-WRENCH.

Q

37

BLACK 1-3/4" PAN HEAD SCREW


R

T

S

T

U

R

Page 24

39



36

47



Step 20

å NOTE: Start all of the hex head SCREWS before completely tightening any of them.

å Fasten the SMALL RIGHT END (V) to the SMALL WIRE

BACK (R) and SHORT LEFT TUBES (T). Tighten four

BLACK 1-3/8" HEX HEAD SCREWS (39) using the

L-WRENCH (36).

å Fasten the SMALL RIGHT END (V) to the LEFT

BOTTOM (U). Use three BLACK 3/8" HEX HEAD


å Tighten all of the hex head SCREWS with the L-WRENCH.

39



36

V

T

U

T

R

36

47



Page 25

Step 21

å Insert two WOOD DOWELS (30) into the short edges of the SMALL UPRIGHTS (W and X).

å Fasten the SHORT TUBES (Y) to the SMALL

UPRIGHTS (W and X). Tighten two HIDDEN CAMS.

å NOTE: Be sure the WOOD DOWELS in the SMALL

UPRIGHTS insert into the holes in the SMALL TUBES.

1

2

X


W


Y

Y

30

Page 26

Step 22

å Insert a WOOD DOWEL (30) into the hole in the SMALL

RIGHT UPRIGHT (X).

å Fasten the SMALL RIGHT UPRIGHT (X) to the LONG

BACK (Z). Tighten the HIDDEN CAM.

å NOTE: Be sure the WOOD DOWEL in the SMALL RIGHT

UPRIGHT inserts into the LONG BACK.

å Fasten the SMALL LEFT UPRIGHT (W) to the LONG BACK (Z).

Use two BLACK 1-9/16" FLAT HEAD SCREWS (38).

1

2

38



30

Z

Sur

W

Sur

X

Sur face with HIDDEN CAM

Page 27

Step 23

å

å

å

Insert four WOOD DOWELS (30) into the LARGE TOP (AA).

Fasten the SMALL UPRIGHTS (W and X) and LONG BACK (Z) to the LARGE TOP (AA). Tighten two HIDDEN CAMS.

Fasten the SMALL RIGHT UPRIGHT (X) and LONG BACK (Z) to the LARGE TOP (AA). Use fi ve BLACK 5/8" FLAT

HEAD SCREWS (43).

å

å

å

å

å

NOTE: Be sure the WOOD DOWELS in the LARGE TOP insert int the holes in the SMALL LEFT UPRIGHT.

Fasten the SMALL ENDS (S and V) to the LARGE TOP(AA). Tighten four HIDDEN CAMS.

NOTE: Be sure the WOOD DOWELS in the LARGE TOP insert into the holes in the SMALL RIGHT END.

Fasten the SHORT BACK (Q) to the LARGE TOP (AA). Use a BLACK 5/8" FLAT HEAD SCREW (43).

Fasten the LONG BACK (Z) to the SMALL RIGHT END (V). Use a BLACK 5/8" FLAT HEAD SCREW (43).

1

43



2

X

W

Z

AA

V Q

S

30

Page 28

Step 24

å Separate the EXTENSION SLIDES (24) from the EXTENSION RAILS (23) as shown in the upper diagram below. Be prepared, the parts are greasy.

å Fasten the EXTENSION RAILS (23) to the SMALL ENDS (S and V) and SMALL LEFT UPRIGHT (W). Use twelve BLACK 1/2" FLAT HEAD

SCREWS (46).

å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION

RAIL in to fi nd the other holes that lines up with the holes in the ENDS and UPRIGHT. Turn a SCREW into these holes.

å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.

24 23

Push the black lever down and pull the SLIDE from the RAIL.

Open end

46



Open end

W

Open end

V

S

Page 29

Step 25

å This step will require two people to fasten the

LARGE TOP (AA) section to the SMALL TOP (E) section.

å

å Carefully stand the SMALL TOP (E) section upright.

Carefully stand the LARGE TOP (AA) section upright.

Fasten the SMALL UPRIGHTS (X and W) to the

SMALL TOP (E). Use four BLACK 1-3/4" PAN

HEAD SCREWS (37).

Pro Tip: Lift with your legs. And, you know, your arms.

AA W

X

E

37

BLACK 1-3/4" PAN HEAD SCREW


Page 30

Step 26

å Fasten the LONG LEFT TUBE (BB) to the SMALL

RIGHT END (V) and FRONT RIGHT TUBE (CC). Tighten two BLACK 3/8" HEX HEAD SCREWS (47) with the

L-WRENCH (36).

CC

BB

V

47



36

Page 31

Step 27

å Turn four METAL PINS (35) into the holes of your choice in the LARGE RIGHT END (M) and LARGE

UPRIGHT (O) for placement of the ADJUSTABLE

SHELF (DD).

å Place the ADJUSTABLE SHELF (DD) onto the

METAL PINS.

å Push three GROMMETS (33) into the large holes in the TOPS (E and AA).

AA

33

E

O

DD

M

35

(4 used)

Page 32

Step 28

å Fasten the hinges on the DOOR (EE) to the LARGE RIGHT

END (M). Use four BLACK 1/2" PAN HEAD SCREWS (45).

45



M

EE

Page 33

Step 29

å Fasten a DRAWER SIDE (HH) to the LARGE DRAWER BOX FRONT (JJ) and the LARGE DRAWER BACK (II). Use four

BLACK 1-9/16" FLAT HEAD SCREWS (38).

å Fasten the DRAWER BRACES (KK) to the LARGE DRAWER BOX FRONT (JJ) and the LARGE DRAWER BACK (II). Use four BLACK 1-9/16" FLAT HEAD SCREWS (38).

å Slide the LARGE DRAWER BOTTOM (LL) into the grooves of the DRAWER SIDE (HH), LARGE DRAWER BACK (II) and

LARGE DRAWER BOX FRONT (JJ).

å Fasten a DRAWER SIDE (HH) to the opposite end of the LARGE DRAWER BOX FRONT (JJ) and the LARGE

DRAWER BACK (II). Use four BLACK 1-9/16" FLAT HEAD SCREWS (38).

38



HH

II

KK

LL

JJ

KK

II

JJ

HH

38


Page 34

Step 30

å Fasten a DRAWER SIDE (HH) to the SMALL DRAWER BACK (MM) and SMALL DRAWER BOX FRONT (NN). Use four

BLACK 1-9/16" FLAT HEAD SCREW (38).

å Slide the SMALL DRAWER BOTTOM (OO) into the grooves of the DRAWER SIDE (HH), SMALL DRAWER BACK (MM) and SMALL DRAWER BOX FRONT (NN)

å Fasten the remaining DRAWER SIDE (HH) to the SMALL DRAWER BACK (MM) and SMALL DRAWER BOX FRONT (NN).

Use four BLACK 1-9/16" FLAT HEAD SCREW (38).

38



MM

HH

OO

NN

MM

HH

NN

HH

38


Page 35

Step 31

å Fasten the SMALL DRAWER FRONT (GG) to the SMALL

DRAWER BOX FRONT (NN). Tighten two BLACK 7/8"

HEX HEAD SCREWS (40) with the L-WRENCH (36).

å Fasten the LARGE DRAWER FRONT (FF) to the LARGE

DRAWER BOX FRONT (JJ). Tighten three BLACK 7/8"

HEX HEAD SCREWS (40) with the L-WRENCH (36).

40



36

JJ

NN

GG

FF

Page 36

Step 32

å Fasten the EXTENSON SLIDES (24) to the DRAWER

SIDES (H) as shown. Use twelve BLACK 1/2" FLAT

HEAD SCREWS (46).

24

H

Open end

24

H

Open end

H

24

Open end

46


(12 used for the EXTENSION SLIDES)

H

24

Open end

46


Page 37

Step 33

å

å Peel APPLIQUES from the APPLIQUE CARD (34) and stick them onto each visible HIDDEN CAM.

To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.

å

å NOTE: Please read the back pages of the instruction booklet for important safety information.

This completes assembly. Clean with a damp cloth. Wipe dry.

25 l bs.

15 l bs.

45 l bs.

60 l bs.

20 l bs.

15 l bs.

30 l bs

.

10 l bs.

34

30 lb s.

Page 38

WARNING

Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart.

Look out for:

• Overloaded shelves or drawers.

• Improper loading can cause the product to be top-heavy.

What can happen:

• Risk of injury.

• Top-heavy furniture can tip over.

• Overloaded shelves and drawers can break.

How to avoid the problem:

• Never exceed the weight limits shown in the instructions.

• Work from bottom to top when loading shelves and drawers. Place the heavier items on the lower shelves or in lower drawers.

• Improperly moving furniture that is not designed and equipped with casters.

• Placing TVs on furniture items that are not designed to support a television is hazardous.

• Furniture can tip over or break if improperly moved.

• Physical injury. Furniture can be very heavy.

• Breakage of tops - particularly with double pedestal furniture (drawers at both ends).

• Risk of injury or death. TVs can be very heavy. Plus the weight and location of the picture tube tends to make TVs unbalanced and prone to tipping forward.

• Unload shelves and drawers from top to bottom before moving the unit.

• Do not push furniture, especially on a carpeted fl oor. Have a friend help you lift the item and set it in place.

• Provide support to the center section of the top when lifting the furniture.

• This product is not designed to support a television.

No results