Kongsberg cNODE Mini Transponder Instruction manual
Kongsberg cNODE Mini Transponder is a versatile underwater positioning and data link system with interchangeable parts. Its modular construction allows for easy replacement of transducer, transponder electronics, battery pack, and options. With a depth rating of up to 7000 meters and a 12 kHz frequency band, the cNODE Mini 17-180-St is well-suited for deep-sea applications. Its 180° omnidirectional beamwidth transducer provides wide coverage, while its compatibility with both HiPAP Cymbal and HPR 400 channels enables precise positioning and reliable data transfer.
Oglas
Oglas
INSTRUCTION MANUAL cNODE Mini LF 7000 m
cNODE Mini
Low Frequency, 7000 m
Instruction Manual
411144/A
June 2016 © Kongsberg Maritime AS
411144/A
June 2016 © Kongsberg Maritime AS
Instruction Manual
Table of contents
ABOUT THIS MANUAL .............................................................. 5
CNODE MINI............................................................................ 6
CABLE LAYOUT AND INTERCONNECTIONS............................. 13
OPERATIONAL PROCEDURES ................................................. 17
MAINTENANCE ...................................................................... 22
SPARE PARTS ........................................................................ 27
411144/A
3
cNODE Mini
TECHNICAL SPECIFICATIONS................................................ 31
DRAWING FILE...................................................................... 36
4
411144/A
About this manual
Observe this general information about the cNODE Mini Instruction Manual; its purpose and target audience.
Purpose of manual
The purpose of this instruction manual is to provide the descriptions and procedures required to install, operate and maintain the cNODE Mini.
Target audience
The manual is intended for all users of cNODE Mini.
Registered trademarks
Observe the registered trademarks that apply.
Windows ® , Windows XP ® , and Windows ® 7 are either registered trademarks, or trademarks of Microsoft Corporation in the United States and/or other countries.
HiPAP ® is a registered trademark of Kongsberg Maritime AS in Norway and other countries.
cNODE ® is a registered trademark of Kongsberg Maritime AS in Norway and other countries.
cPAP ® is a registered trademark of Kongsberg Maritime AS in Norway and other countries.
5
411144/A
6 cNODE Mini
Topics
General supply conditions, page 11
cNODE Mini
411144/A
System description
cNODE Mini is a family of transponders for underwater positioning and data links.
cNODE Mini is designed to be a very versatile system with many interchangeable parts.
The transponders are operated from Acoustic Position Operator Station (APOS) with an acoustic telemetry link for command and data transfer. The transponders are compatible with both HiPAP Cymbal acoustic protocol for positioning and data link, and HPR 400 channels and telemetry. Perform SSBL positioning with a total of 52 HiPAP Cymbal channels and 56 HPR 400 channels, LBL positioning and acoustic link for command and data transfer. The transponders have both transponder and responder functions.
The transponders are rated to up to 7000 m with a housing made of stainless steel. The transponders are designed with a modular construction which means that the transducer, transponder electronics, battery pack and optional add-on’s can be replaced individually to suit the operation.
A transponder is normally a self-contained unit, receiving power from an internal rechargeable battery pack. The transponder can also be powered from an external power supply.
The transponder unit is designed with a modular construction such that the transponder electronics, battery pack and options (where applicable) can be replaced individually.
The transponder may be secured to a subsea structure using mounting brackets.
Note
Always make sure the vent screw is closed before deployment.
Naming description
The transponder name consists of the model name, the model number, the transducer beam width and any options included.
Model name
Mini
Model number
The two digit number in the transponder name describes the frequency band and the depth rating.
First number = Frequency band
1 = 12 kHz
Second number = Depth rating
7 = 7000 meters
411144/A
7
8 cNODE Mini
Transducer beam width
• 180 = 180° beam width
• 50V = 50° vertical beam width
Example of transponder name
The transponder name Mini 17-180-St indicates that this transponder unit is operating in the 12 kHz, rated to 7000 metres depth, with a 180° transducer beam width and a basic end cap. The standard transponder tube material is stainless steel.
Transponder identification
The transponders have labels that identifies:
• the transponder name
• serial number
• default channels
System diagram
The system diagram identifies the main components of the cNODE Mini.
cNODE Mini
A B C D
CD030103_001_001
C
D
A
B
Transducer
Top section module
Tube
End cap module
411144/A
System units
cNODE is a family of transponders for underwater positioning and data links. The cNODE Mini is designed to be a very versatile system with many interchangeable units.
TD180LF
The transducer has a 180° omnidirectional beamwidth, and is available in stainless steel.
Split transponder for remote transducer (S)
This top end cap has a standard external connector for remote transducers.
Transducer cable 6 m
The transducer cable has two Subconn connectors; MCIL4F and
MCIL4M. The cable connects all the remote transducers to the transponder.
TDR180 LF St
The remote transducer has a 180° omnidirectional beam width and is made of Super Duplex stainless steel.
TDR50V LF St
The remote transducer has a 50° vertical beam width and is made of
Super Duplex stainless steel.
411144/A
9
cNODE Mini
Tube
The tube contains the battery and the electronics for the Mini transponder. Available in aluminium and stainless steel.
End cap
The end cap has a vent screw, safety valve with on/off switch and two external connectors and is available in aluminium and stainless steel.
Battery
The battery is a rechargeable nickel-metal hybrid battery.
Battery charger
Charging the battery has some risks, read the procedure first.
Power supply
Use the AC to DC converter for continuous charging of the cNODE Mini from an AC source.
10
411144/A
TTC (Transponder Test and Configuration unit)
The TTC 10 unit is for on deck testing and configuration of low frequency transponders. It can test all KONGSBERG transponder channels, Cymbal and HPR 400. It can also test telemetry transponders with internal and external sensors.
Scope of supply
The following items are provided when you order a transponder.
• Transponder
• Instruction manual
General supply conditions
The following general supply conditions apply to this Kongsberg cNODE Mini delivery.
Receipt, unpacking and storage
Upon accepting shipment of the equipment, the shipyard and/or the dealer must ensure that the delivery is complete and inspect each shipping container for evidence of physical damage.
If the inspection reveals any indication of crushing, dropping, immersion in water or any other form of damage, the recipient should request that a representative from the company used to transport the equipment be present during unpacking.
All equipment must be inspected for physical damage, i.e. broken controls and indicators, dents, scratches etc. during unpacking. If any damage to the equipment is discovered, the recipient must notify both the transportation company and Kongsberg Maritime so that
Kongsberg Maritime can arrange for replacement or repair of the damaged equipment.
Once unpacked, the equipment must be stored in a controlled environment with an atmosphere free of corrosive agents, excessive humidity or temperature extremes.
The equipment must be covered to protect it from dust and other forms of contamination when stored.
411144/A
11
cNODE Mini
Equipment responsibility
Unless otherwise stated in the contract, the shipyard doing the installation and/or equipment dealer becomes fully responsible for the equipment upon receipt.
The duration of responsibility cover:
• The period of time the equipment is stored locally before installation
• The entire installation process
• Commissioning
• The period of time between commissioning and the final acceptance of the equipment by the end user or owner
Unless other arrangements have been made in the contract, the Kongsberg cNODE Mini guarantee period (as specified in the contract) begins when the acceptance documents have been signed.
Support information
If you need support for your Kongsberg cNODE Mini you must contact Kongsberg
Maritime AS.
• Company name : Kongsberg Maritime AS
• Address : Strandpromenaden 50, 3190 Horten, Norway
• Telephone, 24h support : +47 33 03 24 07
• Telefax : +47 33 04 76 19
• Website : http://www.km.kongsberg.com
• Support website : http://www.km.kongsberg.com/support_hpr
• E-mail address : [email protected]
12
411144/A
Cable layout and interconnections
Cable layout and interconnections
Topics
Power converter connectors, page 15
411144/A
13
cNODE Mini
End cap connectors
Battery charger connector
4
5
6
3
2
1
8
7
7
6
Signal connector
5
4
1
8 2
3
CD030103_004_001
The end cap has two connectors:
• External signal connector; 8 pin male subconn MCBH8M for serial line, external power supply and responder signal
• External charge connector; 8 pin female subconn MCBH8F for charging the battery
Signal connector pin out
4
5
2
3
6
7
Pin no.
1
8
Signal
TP TX
GND
TP RX
Responder +
Responder —
GND
Ext. power +15 VDC (use in parallel with 8)
Ext. power +15 VDC (use in parallel with 7)
14
411144/A
Cable layout and interconnections
6
7
8
4
5
2
3
Pin no.
1
Battery charger connector pin out
Signal
Charger A
Charger B
Charger C
NTC A
NTC B
NTC C
GND
GND
Power converter connectors
The end cap has two connectors:
• Power in connector; 6 pin male subconn MCBH6MAS
• Power out connector; 6 pin female subconn MCBH6FAS
Power in connector pin out
4
5
2
3
Pin no.
1
6
Signal
Responder +
115/230 VAC (L)
115/230 VAC (L)
Responder –
115/230 VAC (N)
115/230 VAC (N)
411144/A
15
cNODE Mini
Power out connector pin out
4
5
2
3
6
Pin no.
1
Signal
Responder +
15 VDC
15 VDC
Responder –
GND
GND
16
411144/A
Operational procedures
Topics
Charging the transponder, page 18
Powering up the transponder, page 19
Powering down the transponder, page 20
Setting up the internal tilt sensor, page 21
Configuring the transponder, page 21
17
411144/A
cNODE Mini
Charging the transponder
The battery is charged inside the cNODE Mini. This is connected with some risk, please read the information below and follow the charge procedure carefully.
Prerequisites
Caution
When you are charging the battery ensure good ventilation and stable temperature. Do not cover the transponder. No open fire, sparks or smoking in the area.
NiMH batteries can generate some hydrogen and oxygen gas, the amount depending on certain conditions. Most often this generation occurs during charging.
Procedure
1 Switch off the transponder.
2 Climatize the transponder.
The battery must have a temperature between 5 °C and 40 °C. Recommended charging temperature is 25 °C.
3 Unscrew the vent screw until you feel some resistance (a nylon washer is forced against a metal surface). The O-ring is now visible.
Hold the transponder in an upright position while you do this, so that any water droplets caught around the vent screw comes out, rather than going inside the cNODE Mini.
4 Connect the charger plug to the connector on the transponder marked CHARGE.
5 Connect Power supply to mains (110 or 220 VAC).
6 Switch on the charger.
The charger measures the battery status; all LEDs emit constant yellow light. If the temperature is out of range, the LEDs will flash orange/green.
Fast charge starts and the LEDs emit constant orange light.
When the battery is fully charged the LEDs will be green with a yellow flash every minute.
7 Switch off the charger.
8 Disconnect the charger plug from the transponder.
9 Close the vent screw.
Tighten the vent screw by hand only, until you feel a rather sudden resistance.
(an internal axial O-ring hits a metal surface, compresses 0.3 mm, before 2 metal surfaces meet). The main flat circular surface of the end cap should now align with the edge of a semicircular groove that runs all around the vent screw. This is to visually confirm that the vent screw has been properly tightened.
18
411144/A
Result
When the battery is fully charged the charger will start trickle charging the battery. It is not recommended to trickle charge the battery for a long time. It is better to fast charge, and then top up the battery just before operation.
Further requirements
Caution
When the charging is done, always make sure the vent screw is closed.
Deploying the transponder with the vent screw open will ruin the transponder.
Powering up the transponder
Before deploying the transponder you must connect the battery to the internal circuitry.
Procedure
1 See the alignment markers on the ON/OFF switch.
2 Align the markers using a suitable screwdriver.
Result
The unit transmits bursts when switched on.
Each time the transponder is switched on, it resets to the two default channels.
Note
Always make sure the vent screw is closed before deployment.
411144/A
19
cNODE Mini
Powering down the transponder
Procedure
• Use a suitable screwdriver to move the two marker dots away from each other.
Result
The transponder is off in all three other positions.
Note
Always keep the transponder switched off when not in use.
Always make sure the vent screw is closed before deployment.
Responder function
Procedure
• cNODE will automatically change to responder mode if a responder trigger signal is present. cNODE will change back to transponder mode if no new trigger signal is received within the next 30 seconds.
Result
See APOS online help for setting up a responder.
20
411144/A
Setting up the internal tilt sensor
The transponder needs to face the right way to show the correct values.
Procedure
• Top view of the transponder to the left in this figure - showing the FWD direction.
FWD is marked with the two holes in the bottom end cap module.
Configuring the transponder
The transponder channel and mode can be changed.
Prerequisites
The transponder is configured by Kongsberg Maritime. The channel and mode (FSK or cymbal) may be changed if required. The procedure to change configurations depends on the HiPAP/HPR system in use.
Procedure
• Change the channel and mode either by acoustic telemetry from a HiPAP system or via serial line from a Transponder Test and Configuration unit.
See APOS online help or the instruction manual for the TTC.
411144/A
21
cNODE Mini
Topics
Charging the transponder, page 23
Cleaning the transponder, page 24
Opening the transponder, page 25
Changing the transducer, page 25
Lubricating the subsea connector, page 26
Maintenance
22
411144/A
Charging the transponder
The battery is charged inside the cNODE Mini. This is connected with some risk, please read the information below and follow the charge procedure carefully.
Prerequisites
Caution
When you are charging the battery ensure good ventilation and stable temperature. Do not cover the transponder. No open fire, sparks or smoking in the area.
NiMH batteries can generate some hydrogen and oxygen gas, the amount depending on certain conditions. Most often this generation occurs during charging.
Procedure
1 Switch off the transponder.
2 Climatize the transponder.
The battery must have a temperature between 5 °C and 40 °C. Recommended charging temperature is 25 °C.
3 Unscrew the vent screw until you feel some resistance (a nylon washer is forced against a metal surface). The O-ring is now visible.
Hold the transponder in an upright position while you do this, so that any water droplets caught around the vent screw comes out, rather than going inside the cNODE Mini.
4 Connect the charger plug to the connector on the transponder marked CHARGE.
5 Connect Power supply to mains (110 or 220 VAC).
6 Switch on the charger.
The charger measures the battery status; all LEDs emit constant yellow light. If the temperature is out of range, the LEDs will flash orange/green.
Fast charge starts and the LEDs emit constant orange light.
When the battery is fully charged the LEDs will be green with a yellow flash every minute.
7 Switch off the charger.
8 Disconnect the charger plug from the transponder.
9 Close the vent screw.
Tighten the vent screw by hand only, until you feel a rather sudden resistance.
(an internal axial O-ring hits a metal surface, compresses 0.3 mm, before 2 metal surfaces meet). The main flat circular surface of the end cap should now align with the edge of a semicircular groove that runs all around the vent screw. This is to visually confirm that the vent screw has been properly tightened.
411144/A
23
cNODE Mini
Result
When the battery is fully charged the charger will start trickle charging the battery. It is not recommended to trickle charge the battery for a long time. It is better to fast charge, and then top up the battery just before operation.
Further requirements
Caution
When the charging is done, always make sure the vent screw is closed.
Deploying the transponder with the vent screw open will ruin the transponder.
Cleaning the transponder
The transponder must be cleaned after use.
Procedure
1 Remove any growth and dirt with a stiff brush or a wooden or plastic scraper. Be careful not to damage the transducer.
2 Clean the unit thoroughly with lots of fresh water.
3 Dry off, so no water can come inside when opening.
Inserting an O-ring
The O-rings must be inspected for damage as often as possible.
Procedure
Note
Make sure to keep the O-rings and mating surfaces free of dust and debris.
Do not use a screwdriver or similar when removing the O-ring, use an O-ring tool.
1 Open the transponder.
2 Remove the existing O-ring.
3 Clean the surface and cover it with a thin film of silicone grease.
Use lint-free objects when cleaning the surfaces.
4 Insert the new O-ring.
24
411144/A
5 Close the transponder.
Opening the transponder
In order to replace the WBAT transceiver battery - and to access the electronic module for maintenance - the unit must be opened.
Prerequisites
The WBAT transceiver must be cleaned and dried before opening, so that no dirt or water seeps into the unit when it is opened.
Procedure
1 Pull out the lock cord between the tube and the end cap.
If the lock cord is hard to remove, try carefully opening the vent screw. Pressure may have built up inside the transponder.
2 Remove the end cap.
There is a 5 mm orientation peg at either end of the tube. When pulling apart, make sure to keep this orientation until all parts are completely free from each other. Forceful twisting of the parts relative to each other while the internal parts are still mated, will damage the unit.
3 Pull out the lock cord between the transducer and the tube.
4 Remove the transducer carefully, the chassis and the battery is fastened to the transducer.
5 Replace the O-rings that are damaged or used for more than a year.
6 Make sure the mating surfaces and the O-rings are completely clean and wipe a thin film of silicone grease over the rings and mating surfaces.
Result
Follow the procedure for opening the transponder in reverse order to close it.
Changing the transducer
The transducer is a sealed unit and does not open. If the transducer is damaged, replace the whole unit.
Prerequisites
The transponder needs to be clean and open to change the transducer.
411144/A
25
cNODE Mini
Procedure
1 Remove the battery carefully.
2 Unscrew the chassis from the transducer.
3 Make sure the new transducer is of the same type as the old.
4 Fasten the transducer to the chassis and fit the battery.
Further requirements
Assemble the transponder.
Lubricating the subsea connector
The subsea connector must be kept clean from grit and dirt.
Prerequisites
Caution
Do not use silicone based sprays like 5–55, WD-40 or similar. These products will degrade the rubber fused around the metal pins.
Procedure
1 Remove the dummy plug or the external cable from the connector.
2 Apply Molykote 44M silicone based grease.
Half a match head dose per contact is enough.
26
411144/A
Spare parts
Topics
cNODE Mini maintenance kit spare part, page 28
Split transponder (S) for remote transducer spare part, page 28
Transducer cable 6 m spare part, page 28
End cap steel spare part, page 29
Chassis with PCB spare part, page 29
Battery charger spare part, page 30
Power supply St spare part, page 30
Transponder Test and Configuration unit (TTC10) spare part, page 30
27
411144/A
cNODE Mini
cNODE Mini maintenance kit spare part
• Part name: cNODE Mini maintenance kit
• Part number: 351794
The kit consists of:
• 2 locking cords
• 4 O-rings 58 mm
• 2 locking sleeves MCDLSF
• 1 female dummy plug
• 1 male dummy plug
• 1 O-ring 12 mm
• 1 O-ring 10 mm
TD180 St spare part
• Part name: TD180 St Mini Steel
• Part number: 320885
Split transponder (S) for remote transducer spare part
• Part name: Split transponder (S) for remote transducer
Stainless steel
• Part number: 330071
Transducer cable 6 m spare part
• Part name : Transducer cable, 6 m
• Part number : 345772
28
411144/A
TDR180 LF spare part
• Part name : TDR180 LF St
• Part number : 394785
TDR50V LF spare part
• Part name : TDR50V LF
• Part number : 330015
Tube spare part
• Part name : cNODE Tube stainless steel
• Part number : 381343
End cap steel spare part
• Part name: cNODE Mini end cap steel
• Part number: 349131
Chassis with PCB spare part
Chassis with circuit board for low frequency transponders.
• Part name: cNODE Mini chassis LF
• Part number: 354758
Battery spare part
• Part name: Battery
• Part number: 290–220687
411144/A
29
cNODE Mini
Battery charger spare part
• Part name: Battery charger cNODE Mini
• Part number: 290-220687
Power supply St spare part
• Part name: cNODE Power supply Steel
• Part number: 367386
Transponder Test and Configuration unit
(TTC10) spare part
Transponder test and configuration unit for low frequency transponders.
• Part name: TTC 10
• Part number: 364845
30
411144/A
Technical specifications
Topics
Performance specification, page 32
Weight and outline dimensions, page 33
Environmental specifications, page 35
411144/A
31
cNODE Mini
Performance specification
These performance specifications summarize the main functional and operational characteristics of the cNODE Mini.
cNODE Mini 17 series
• Frequency band : Low frequency (LF)
• Maximum depth rating : 7000 m
Internal tilt
• Max. detectable angles : ±90°
• Accuracy : ±2°
Responder trigger signal
Responder trigger connection via the external signal connector.
• Logic pulse : Positive
• Amplitude : 5 to 25 V
• Duration : 2 to 6 ms
TD180 LF
• Beam pattern :
• Transducer beam : 180° vertical
• Frequency band : Low frequency
• Receiver sensitivity : 100 dB
• Maximum source levels :
– Max 188 dB
– High 182 dB
– Low 176 dB
– Min 168 dB
Battery charger
• Charge method : Constant current, charging the three battery strings individually
• Detection method for fully charged battery : Temperature rise, maximum temperature and maximum time (165 min.)
• Charging time : 2 hours 45 minutes for an empty battery
32
411144/A
Weight and outline dimensions
These weights and outline dimension characteristics summarize the physical properties of the cNODE Mini.
cNODE Mini 17–180–St
Transponder cNODE Mini
17–180–St
Weight in air
15.5 kg
Weight in water Height
11.5 kg 661 mm
Diameter
85 mm
TD180LF
• Height : 70.5 mm
• Diameter : Ø88 mm
Tube
• Height : 495 mm
• Diameter : Ø85 mm
Basic end cap
• Height : 31.5 mm
• Diameter : Ø85 mm
Floating collar
• Height : 845 mm
• Width : 290 mm
Power supply
• Height : 309.2 mm
• Diameter : Ø85 mm
Battery charger
Weight
2.9 kg
Height
83 mm
Width
256 mm
Depth
355 mm
411144/A
33
cNODE Mini
Power specifications
These power characteristics summarize the power specifications for the cNODE Mini.
cNODE Mini battery lifetime
• Quiescent : 60 days
Mini 17–180 series – Cymbal
Update rate
1 seconds
[days]
TX power level
Minimum 5.7
Low
High
4.2
2.1
Maximum 0.5
2 seconds
[days]
6.0
5.1
3.2
1.1
3 seconds
[days]
6.1
5.4
3.8
1.5
4 seconds
[days]
6.2
5.6
4.2
1.9
5 seconds
[days]
6.2
5.8
4.5
2.2
10 seconds
[days]
6.3
6.1
5.3
3.3
Mini 17–180 series – FSK
Update rate
1 seconds
[days]
TX power level
Minimum 10.1
Low
High
8.5
5.3
Maximum 1.8
2 seconds
[days]
10.4
9.5
7.1
3.1
3 seconds
[days]
10.5
9.9
8.0
4.1
4 seconds
[days]
10.6
10.1
8.5
4.8
5 seconds
[days]
10.6
10.2
8.9
5.4
10 seconds
[days]
10.7
10.5
9.7
7.3
Mini 17–S with TDR50V – Cymbal
Update rate
TX power level
1 seconds
[days]
Minimum 5.7
Low 3.5
High 1.2
Maximum 0.3
2 seconds
[days]
6.0
4.5
2.1
0.6
3 seconds
[days]
6.1
5.0
2.8
0.9
4 seconds
[days]
6.2
5.3
3.3
1.2
5 seconds
[days]
6.2
5.5
3.6
1.5
10 seconds
[days]
6.3
5.9
4.6
2.4
34
411144/A
Mini 17–S with TDR50V – FSK
Update rate
1 seconds
[days]
TX power level
Minimum 10.1
Low
High
7.5
3.6
Maximum 1.1
2 seconds
[days]
10.4
8.8
5.4
2.0
3 seconds
[days]
10.5
9.4
6.5
2.8
4 seconds
[days]
10.6
9.7
7.2
3.4
5 seconds
[days]
10.6
9.9
7.8
3.9
10 seconds
[days]
10.7
10.3
9.0
5.8
Battery charger
• Voltage requirement : 110 or 220 V
Environmental specifications
These environmental specifications summarize the temperature and humidity requirements for the cNODE Mini.
All cNODE Mini transponders
• Operational temperature : –5 to +55°C
• Storage temperature : –40 to +70°C
Battery
• Operational temperature : -5 to +55°C
• Storage temperature : -20 to +30°C
• Storage humidity : <50% relative
Battery charger
• Operational temperature : 5 to 40°C for fast charging
• Storage temperature : –40 to +70°C
• Relative humidity : 10 to 90% relative non-condensing
• Ingress protection : IP30
411144/A
35
cNODE Mini
Topics
cNODE Mini 17-180-St outline dimensions, page 37
Drawing file
36
411144/A
cNODE Mini 17-180-St outline dimensions
Drawing 351217
Ø94
595 527
Weight in water: 1 1.5 kg
Weight in air: 15.5 kg
All measurements in mm.
The drawing is not in scale.
411144/A
102
Ø85
[351217] Rev .A
CD12_351217_001_001
37
cNODE Mini
Index
290-220687 battery charger (spare part) ............................. 30
290–220687 battery (spare part)....................................... 29
TD180 St (spare part) ................................... 28
330071 split transponder (S) for remote transducer
(spare part) .............................................. 28
351794 maintenance kit (spare part) ............................ 28
354758 chassis (spare part)....................................... 29
TTC 10 (spare part)...................................... 30
367386 power supply (spare part)............................... 30
381343 tube (spare part) .......................................... 29
A
description ................................................. 7
power supply ............................................. 10
transducer .................................................. 9
TTC ........................................................ 11
tube ........................................................ 10
activate responder function ....................................... 20
audience this manual................................................. 5
B
battery description ................................................ 10
spare part.................................................. 29
battery charger description ................................................ 10
spare part.................................................. 30
block diagram..................................................... 8
C
characteristics performance .............................................. 32
charging
transponder .......................................... 18, 23
chassis spare part.................................................. 29
cleaning transponder ............................................... 24
cNODE naming description ....................................... 7
D
system ...................................................... 7
transducer .................................................. 9
TTC ........................................................ 11
tube ........................................................ 10
dimensions specifications ............................................. 33
drawing system diagram............................................ 8
E
end cap top.......................................................... 25
environmental requirements .............................................. 35
responsibility ............................................. 12
storage ..................................................... 11
F
functional diagram..................................................... 8
G
general supply conditions.................................. 11
equipment responsibility................................ 12
H
how to open the transponder .................................... 25
humidity requirements .............................................. 35
I
38
411144/A
Index
support .................................................... 12
inserting o-ring ...................................................... 24
K
Kongsberg Maritime support .................................................... 12
L
lubricating subsea connector ......................................... 26
M
maintenance kit spare part.................................................. 28
N
naming description cNODE ..................................................... 7
O
o-ring inserting ................................................... 24
open transponder ............................................... 25
order number chassis ..................................................... 29
power supply ............................................. 30
TTC 10 .................................................... 30
outline dimensions specifications ............................................. 33
P
performance specifications ............................................. 32
pin out end cap connectors....................................... 14
power converter connectors ............................ 15
power requirements .............................................. 34
power converter description ................................................ 10
pin out ..................................................... 15
power down transponder ............................................... 20
power supply description ................................................ 10
spare part.................................................. 30
power up transponder ............................................... 19
procedure opening the transponder................................. 25
R
reader this manual................................................. 5
receipt general supply conditions............................... 11
registered trademarks........................................ 5
remote transducer cable spare parts................................................. 28
replacement transducer ................................................. 25
power ...................................................... 34
temperature ............................................... 35
responder activate .................................................... 20
responsibility equipment ................................................. 12
S
scope of supply.............................................. 11
spare part..................................................... 27
battery ..................................................... 29
battery charger ........................................... 30
chassis ..................................................... 29
maintenance kit .......................................... 28
power supply ............................................. 30
split transponder (S) for remote transducer .......... 28
TD180 St.................................................. 28
TDR180 LF............................................... 29
TDR50V LF .............................................. 29
TTC 10 .................................................... 30
tube ........................................................ 29
spare parts remote transducer cable ................................. 28
performance .............................................. 32
weight ..................................................... 33
standard items provided with the delivery.............................. 11
start transponder ............................................... 19
stop transponder ............................................... 20
storage general supply conditions............................... 11
subsea connector lubricating................................................. 26
supply conditions ........................................... 11
equipment responsibility................................ 12
receipt ..................................................... 11
411144/A
39
cNODE Mini
support information......................................... 12
system diagram..................................................... 8
system description ........................................... 7
system units transducer .................................................. 9
T
target audience this manual................................................. 5
TD180 St spare part.................................................. 28
TDR180 LF spare part.................................................. 29
TDR50V LF spare part.................................................. 29
temperature requirements .............................................. 35
tilt sensor internal .................................................... 21
top end cap open........................................................ 25
trademarks registered................................................... 5
transducer description ................................................. 9
replacement ............................................... 25
transponder
charging .............................................. 18, 23
cleaning ................................................... 24
configuration.............................................. 21
open........................................................ 25
power down............................................... 20
stop ........................................................ 20
tilt sensor.................................................. 21
TTC description ................................................ 11
TTC 10 spare part.................................................. 30
tube description ................................................ 10
spare part.................................................. 29
U
unpacking general supply conditions............................... 11
W
weight specifications ............................................. 33
wiring end cap connectors....................................... 14
information ............................................... 13
power converter connectors ............................ 15
40
411144/A
©2016 Kongsberg Maritime
Prenesi
Javna povezava posodobljena
Javna povezava do vašega klepeta je bila posodobljena. You may view and manage your chat links after registration here.
Javna povezava do dokumenta
Oglas
