advertisement
NOTE: DO NOT PRINT RED LINES. DASHED LINES SHOW FOLD PLACEMENT.
MIW-XT INSTALLATION INSTRUCTIONS
CAUTION:
Only for use with 15 Amp branch circuits utilizing 14 or 12 gauge wire. Make sure the branch circuit is de-energized before installation.
AC Circuit
MIW-XT SPECFICATIONS
AC Outlets, Total: .............................1
Power Inlet Faceplate
AC Connector: .....................IEC 320 C14
NOTE:
The type of installation and outlet box will determine which components are used. The MIW mounting ears will only be attached on old work installations using the Raco 508 electrical box.
Line Voltage: ....................120V, 60Hz
Total Current Capacity: ................15A
IEC Power Inlet Cord
Signal Line Protection: .......Not Included /
Modules Sold
Separately
STEP 1:
Determine which signal line and outlet box configuration you will be using before beginning installation, as it may affect which components are installed. The kit can be used with the included MIW Pass-Through Insert or with a variety of signal line products (sold separately): Panamax signal line modules, Keystone inserts (fig.1), or Decora
STEP 2:
® signal line inserts (fig.2).
Select a location close to the equipment. In the case of a Plasma TV, this
Length: ......................................6 feet
Connectors: ....................IEC 320 C13
NEMA 5-15P
Flat Plug AC Power Cord
Length: ................................11 inches
Connectors: ...................NEMA 5-15P
NEMA 5-15R
SCREEN PRINT ART FOR FRONT OF PFP MIW-POWERKIT-PFP INLET FACEPLATE (TWISTLOCK RECEPTACLE)
Plasma TV is mounted. Cut a 3 3/4” wide by 3 3/4” high hole in the wall for the outlet box. (When using mounting ears, cut a 4 1/8” wide by 4 1/4” high hole in the wall for the outlet box).
One each In-Wall power inlet and outlet enclosure
Power Outlet Faceplate
AC Connector: ......................NEMA 5-15R
Noise Filtration: .............................Level 1
Signal Line Protection: .......Not Included /
CONTENTS*
(Side
View)
Modules Sold
Separately
(Back
View)
FRONT
VIEW
SIDE
VIEW
BACK
VIEW
PLUG
SECURING
CLIP
STEP 3:
Run the source wire (e.g. Romex) through an opening in the outlet box
(both sold separately).
No more than 1” of wire sheath should extend into the outlet box. 3” of wire should be able to extend beyond the opening of the outlet box. Install the outlet box into the hole.
11” flat plug adapter power cord (1)
6’ IEC power cord & securing clip (1)
STEP 4:
Attach the mounting bracket to the outlet box (fig. 4).
If not using a dual-gang, divided outlet box, you will need to attach the
Decora assembly or module bay assembly to the mounting bracket (fig.
3) using the #6-32 nuts and lock washers before installing the mounting bracket to the wall. If using a dual-gang outlet box, the nuts and washers will need to be removed.
STEP 6:
Run the signal line(s) through the low-voltage signal bay.
If using the MIW Pass-Through Insert (fig. 7), remove the rubber grommet and cut a hole in the rubber grommet so that it fits snugly around the signal line. Pass the signal line through the signal bay, place the rubber grommet over the signal line, and put the rubber grommet back in place.
MIW Pass-
Through Insert
(2)
Decora® adapter (2)
Keystone module insert
(2)
(6) Wire Nuts, 14/14 and 12/14 AWG solid wire compatible
(8) #6-32 8mm Flat Head Philips Faceplate Screws
(8) #6-32T Pan Head Mounting Screws - Philips
(2) Mounting Brackets
(4) Mounting Bracket Ears
(4) #2.6-28T screws for Mounting Post
(4) #6-20T screws for Mounting Bracket Ears
(1) Mounting Template
STEP 5:
Strip AC wire (e.g. Romex) and connect using the included wire nuts. First connect the ground wire (green insulated) on the Max In-Wall and bare copper on the building wire. Then connect the neutral wire (white), then the hot wire (black).
* Installation options will determine which parts are used. Not all components will be utilized.
QUESTIONS ABOUT PF POWER PRODUCTS?
PFPower by Panamax~Furman
1690 Corporate Circle
Petaluma, CA 94954
Phone - 707-283-5900 or 800-472-5555
Customer Relations
7:30 AM – 4:30 PM,
M-F, Pacific Time (PST)
Email - [email protected]
Fax - 707-283-5901
Web - www.panamax.com or www.furmansound.com
© 2009 PFPower is a Trademark of Panamax, Inc
Max In-Wall is a Trademark of Panamax, Inc
Decora® is a Registered Trademark of Leviton Manufacturing Co, Inc.
MIW-XT
MAX IN-WALL™ POWER MANAGEMENT EXTENDER SYSTEM
Installation Instructions
• Power and signal lines are hidden in the wall or behind panel displays
for a clean, tidy and professional installation.
• Extend Connected Equipment Policy to remote equipment when
used with Panamax/Furman Power Management components.
• Ultra-thin profile can allow equipment to hang less than one inch
from the wall.
• Accommodates optional MIW Signal Line Modules
(
MIW modules sold separately
).
• CSA certified for code compliant installations.
• EMI/RFI noise filtration built into outlet receptacle.
• 3 Year Product Warranty.
Kit Includes Components for Four Possible Installation Configurations:
1.
3.
2.
4.
Signal line module bay provides variety of optional installation solutions by using:
1. Decora ® adapter • Trim plate to accommodate a variety of audio/ video
connections.
2. Pass-through insert • For Keystone adapter or rubber grommet.
3. Keystone 2-port adapter • For flexible connection capability.
Optional Signal Protection Module Usage:
Panamax In-Wall signal protection modules (fig. 8) may be used to provide a clean looking interface for the signal lines.
1690 Corporate Circle, Petaluma, CA. 94954 www.panamax.com or www.furmansound.com
4. MIW Signal Line Modules
• MIW-5RCA • MIW-VGA • MIW-SVIDEO • MIW-DATA
(MIW modules sold separately, contact Panamax/Furman)
INS00848 REV C 03/09 1
NOTE: DO NOT PRINT RED LINES. DASHED LINES SHOW FOLD PLACEMENT.
MIW-XT INSTALLATION INSTRUCTIONS
fig. 1 MIW-XT
With Keystone insert fig. 2 MIW-XT With Decora
® adapter
PASS THROUGH CONFIGURATION
New work installation using signal bay and Carlon
SC200DV plastic electrical box.
DECORA CONFIGURATION
Installation using Decora adapter and Carlon
B114R electrical box.
Electrical box
(not included)
Decora ® trim plate adapter
Decora ® 6-port insert
(not included)
Mounting
Bracket
Electrical box
(not included) fig. 3 Mounting Bracket with keystone module insert option fig. 4 Mounting Bracket and wall cut-out
Retaining
Clip
IEC Cord fig. 5 Mounting Bracket installed, rear view showing mounting ears fig. 6 Rear of MIW-XT showing wire pigtails fig. 7 MIW Pass-
Through Insert fig. 8 Panamax Max In-Wall
Signal Line Protection Module
Rubber
Grommet
MIW Pass-Through
Insert
Faceplate
Low-voltage signal bay
Rubber Grommet
MIW Pass-Through
Insert
Mounting
Bracket
Electrical box
(not included)
Installation requires use of an outlet box or boxes that are NOT provided with the product. Product has been tested thoroughly to
be compatible with the following outlet boxes:
NEW WORK
Plastic: Carlon SC200DV
Metal: Raco 8355
OLD WORK
Carlon B114R
Raco 508 (hardware removed)
Faceplate
Faceplate
#6-32 countersunk screw
(not included)
Decora ® trim plate adapter
Mounting
Bracket
Decora ® 6-port insert
(not included)
Retaining
Clip
IEC Cord
KEYSTONE CONFIGURATION
#6-20 screw
Installation using Keystone insert and Raco 508
(or 8500) electrical box.
Mounting Post Mounting Ear
Electrical box (not included)
#2.6-28 screw
Faceplate
Keystone
Module
Insert
#6-20 screw
Mounting
Post
Mounting
Ear
Electrical box (not included)
#2.6-28 screw
Faceplate Keystone
Module
Insert
MIW Pass-
Through
Insert
Mounting
Bracket
Low-voltage signal bay
Retaining
Clip
IEC Cord
MIW Pass-
Through Insert
Mounting
Bracket
Low-voltage signal bay
advertisement
Related manuals
advertisement