SolarEdge Monitoring Platform Installation Guide
SolarEdge Monitoring Platform offers the following range of features and functionalities:
- Remote monitoring of photovoltaic power plants over the internet
- Real-time data on plant performance, including power output, energy yield, and efficiency
- Historical data for performance analysis and trending
- Fault and event detection and alerts
- Troubleshooting and diagnostics tools
- Reporting and analytics for performance optimization
- Mobile access for on-the-go monitoring
Additionally, the platform provides advanced features such as:
- Detailed module-level monitoring for identifying underperforming modules and optimizing system performance
Advertisement
Advertisement
0
Monitoring Platform
User’s Guide
For System Owners
Version 2.1
Managing an Alternative Power Source with a Power Plant Controller MAN-01-00xxx
1
Disclaimers
Important Notice
Copyright © SolarEdge Inc. All rights reserved.
No part of this document may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photographic, magnetic or otherwise, without the prior written permission of SolarEdge Inc.
The material furnished in this document is believed to be accurate and reliable. However, SolarEdge assumes no responsibility for the use of this material. SolarEdge reserves the right to make changes to the material at any time and without notice. You may refer to the SolarEdge web site ( www.solaredge.com
) for the most updated version.
All company and brand products and service names are trademarks or registered trademarks of their respective holders.
Patent marking notice: see http://www.solaredge.com/patent
The general terms and conditions of delivery of SolarEdge shall apply.
The content of these documents is continually reviewed and amended, where necessary. However, discrepancies cannot be excluded. No guarantee is made for the completeness of these documents.
The images contained in this document are for illustrative purposes only and may vary depending on product models.
Monitoring Platform User’s Guide for System Owners
2
Emission Compliance
This equipment has been tested and found to comply with the limits applied by the local regulations.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
Monitoring Platform User’s Guide for System Owners
3
Version History
Version 2.1, August 2020 – added layout chapter
Version 2.0, March 2020 – updated user interface screenshots
Version 1.0, November 2019 – first release
Contents
Monitoring Platform User’s Guide for System Owners
4
Introducing the SolarEdge Monitoring Platform
The SolarEdge monitoring platform enables monitoring the technical and financial performance of one or more Photovoltaic sites with SolarEdge equipment. It provides accurate information about present and past performance of each module individually and about the system as a whole, enabling users to detect, pinpoint and troubleshoot faults, efficiently manage maintenance operations and analyze site profitability.
Smart algorithms continuously track the power, voltage, and current of all modules and inverters, as well as a range of statistical and meteorological indicators to detect performance events that require intervention or maintenance.
These features enable installers and system owners to verify site functionality and monitor its performance.
Using the SolarEdge Monitoring Platform
Getting Started
To use the SolarEdge monitoring platform, your system installer will create and register your system and then add you as the system owner.
Once the installer initiates your registration, you will receive an invitation e-mail with a link to a form to fill in.
To activate your account:
1.
Click the link sent to you in the invitation email message. The registration form is displayed:
Figure 1: Registration Form
2.
Enter your details and select the required check-boxes.
3.
Click Save to complete the registration and get access to your solar system.
4.
When the "Thank You" page appears (Figure 2), click Log in to the Monitoring platform . The Login window is displayed (Figure
3).
Monitoring Platform User’s Guide for System Owners
Figure 2: Thank You Page
To launch the SolarEdge monitoring platform:
1.
Do one of the following:
Go to https://monitoring.solaredge.com
.
From the SolarEdge website, click the Monitoring Platform Login link at the top of the screen.
The Login window is displayed.
5
Figure 3: Login Window
2.
Enter your e-mail and password (as filled in the registration form) and click Login .
Monitoring Platform User’s Guide for System Owners
6
User Settings
To set user preferences:
1.
Click the dropdown arrow next to your username and select User Settings . The User Settings window is displayed.
Figure 4: User Settings Window
2.
Set the following:
First Name
Last Name
Phone number
Zip Code
Address
Change password – Click and modify if necessary
System Units: Metric or Imperial
Language: Select the language in which the monitoring platform will display. When you change the language, the localized data changes automatically, including numbers, currency and date formats.
3.
Click Save .
Monitoring Platform User’s Guide for System Owners
7
Home Page
The home page lists all the installed sites that you have permission to view. It provides an overall view of the various sites managed by the monitoring platform.
require access to additional sites, contact your installer.
Figure 5: Home Page
To use the home page:
1.
Click Home at the top right toolbar. The site list is displayed containing the following information about each site:
Column Description
Site Name
A link to more information about a site. Click the site name to display the site dashboard .
Address
Peak Power
Information on a site’s physical location.
Specifies the total DC power ratings of all the modules.
2.
Do the following as required:
To control which columns appear, click Choose Columns to open a dropdown list, and check the boxes for the columns you wish to display.
Monitoring Platform User’s Guide for System Owners
8
Figure 6: Displaying Columns
To sort the site list by the values in any column, click on the column’s title. This toggles the order from ascending to descending and vice versa. Alternatively, click the column's dropdown arrow and select either Sort Ascending or Sort
Descending.
Use the navigation bar above the list to navigate through the pages and refresh site information.
Search for a specific site using the search box. The search text is remembered even if the browser is closed and re-opened.
Site Dashboard
The Dashboard provides a high-level view of the information collected by the monitoring platform for a specific site.
To access a site's dashboard, simply click on the site name in the home page site list. If you only have access to one site, the site’s
Dashboard is automatically displayed.
Monitoring Platform User’s Guide for System Owners
Navigation bar
Site overview
Power flow
Power and energy
Site selection menu
9
Site details
Weather data
Environmental benefits
Comparative energy
Figure 7: Site Dashboard
Monitoring Platform User’s Guide for System Owners
10
How to read the site dashboard
Site overview
The site overview area shows accumulated energy and revenue for the site. Each box specifies a value and its measurement unit.
The revenue is calculated by multiplying the site-specific feed-in tariff per kWh by the actual energy produced. The revenue is displayed in the currency predefined by the user.
Figure 8: Site Overview
Power flow diagram
The Power Flow diagram shows real-time system behavior – from solar production to site consumption, and grid import or export.
For systems equipped with StorEdge, the battery charge / discharge status and state of energy will also be shown.
Figure 9: Power Flow Diagram
Power and energy
If a consumption meter is installed, a consumption bar is displayed * . The consumption reading represents your solar energy consumption:
System production – the bar represents the solar energy produced in terms of self-consumption and export. The selfconsumption percentage represents the amount of solar energy that used to power site loads, while the export percentage represents the amount of solar energy that was exported to the grid.
Consumption – the bar represents the total energy consumed in terms of self-consumption and import. The selfconsumption percentage represents the amount of energy consumed from solar energy, while the import percentage represents the amount of energy consumed from the grid.
Figure 10: Consumption Bar
* If a meter is not installed in the site, contact your installer to install a consumption meter in order to gain access to consumption and self-consumption data.
Monitoring Platform User’s Guide for System Owners
11
The power and energy chart is found directly below the consumption bar (when it appears). The chart shows the power production of this site over a specified period. The default period is the billing cycle.
The X-axis represents time and the Y-axis represents the power produced in kW (when in Day or Week view), or the energy produced in kWh (when in Month, Billing Cycle, or Year view). Use the tabs above the graph to select the desired view.
Power level is a function of variable factors, such as the irradiance level and ambient temperature. Therefore, the power-curve typically rises and falls each day.
If there is a data connection between a production meter and your SolarEdge system, then the production data displayed here is taken from the meter's readings. If not, the data is taken from your site inverter or module production readings.
Figure 11: Weekly Power and Energy Chart View
How to read the power and energy chart
The solar production shown in green represents the power or energy produced from the sun. The consumption, marked in red, displays the site's loads consumption. In blue, the self-consumption is shown.
Monitoring Platform User’s Guide for System Owners
12
Comparative energy
The comparative energy chart compares the energy produced at the site during corresponding periods in previous years. You can select to compare months or quarters of different years, or even entire years’ output.
Figure 12: Comparative Energy Chart
Site Details
The site details box displays general information about the site - status, ID, name, location, date installed, date the information was last updated, and the site's peak power.
If an EV charger or smart energy products are connected in the site, an indication for each one will also be displayed.
Figure 13: Site Details
Monitoring Platform User’s Guide for System Owners
Weather
The Weather area shows the current weather conditions together with other details as well as the forecast for the next few days.
This information may be helpful when estimating future power production levels.
13
Figure 14: Weather
Environmental Benefits
The environmental benefits area shows the accumulated impact that non-renewable energy producing methods would have had on the environment had they have been used to produce the amount of energy generated by this site. To learn how the environmental benefits are calculated read our dedicated technical note .
Figure 15: Environmental Benefits
Monitoring Platform User’s Guide for System Owners
14
Layout
Overview
The layout window shows a schematic outline that represents inverters, their strings and the modules in each string. Near-real-time performance data is displayed for these components.
To view the layout, select a site and click the icon in the top-left corner of the screen.
Use the layout to:
View the latest performance of specific components.
Compare and analyze the performance of various components, such as modules.
Pinpoint the location of alerted components.
See how components are connected to each other.
The layout offers both physical layout and logical layout views, as follows:
Physical layout: Shows a bird’s eye view of the actual placement of each component in the site, including inverters, clusters, strings and modules.
Logical layout: Shows a schematic logical view of the components in the site, meaning inverters, clusters, strings, modules and their electrical connectivity.
Physical Layout
The physical layout schematic shows a layout of the components in the field: inverters, clusters, strings, modules and their physical arrangement in the site. This layout offers a virtual bird’s eye view of the system’s components and their location, which functions as a usable tool for troubleshooting maintenance problems.
Figure 16: Physical Layout
When in the physical layout window, click the layout schematic.
button in the toolbar and select logical layout to display the logical
If a physical layout was not created for the site, the logical layout will be the default view.
Monitoring Platform User’s Guide for System Owners
15
Elements in the Physical Layout Schematic
A sample physical layout schematic is shown in the figure below:
Figure 17: Elements in the Diagram
For each system component in the layout diagram (inverters and modules), the following information is displayed:
Amount of Energy: Indicates the energy produced by this component and its underlying components in the period chosen above the diagram.
Color Code: In the layout schematic, all the elements of the diagram are color coded according to the amount of energy
they have produced in the timeframe specified by the buttons in the toolbar .
The color-coding is comparative, that is, a module which has produced the most energy over the selected timeframe is displayed in light blue, while a module which has produced less energy is darker.
The color-coding is also normalized, so the modules’ color is relative to their full capacity. For example, a 300W module is the same color as a 400W module, when both produce the same percentage of their full capacity. Normalization is also in accordance with the number of power optimizers connected to each string.
Diagram Sizing
The layout diagram can be fitted to your viewing needs:
Zoom in/out : Make the diagram smaller or larger. Click the + button to zoom in or the - button to zoom out. When using a mouse, you can also use the wheeling scroll to zoom in or out.
Fit to screen : Resizes the display of the diagram to fit in the screen
Figure 18: Diagram Sizing Options
Monitoring Platform User’s Guide for System Owners
16
Navigator Tool
The Navigator tool at the top right-hand side of the window indicates the area displayed in the diagram using a red frame. When zooming in the layout, the red frame can be dragged to display other areas in the layout.
Figure 19: Navigator Tool
Logical Layout
The Logical Layout shows a schematic logical layout of the components in the site: inverters, strings, modules and their electrical connectivity. This layout displays a logical view of the installation site, showing which modules are connected in each string, which strings are connected to each inverter, etc.
The following diagram displays the Logical Layout of the installation whose Physical Layout was shown above:
Figure 20: Logical Layout
NOTE
The Layout schematic automatically zooms in or out, based on the number of components displayed in the window.
When in the Logical Layout window, click the
Layout diagram.
button in the toolbar and select Physical Layout to display the Physical
Both windows show the inverter with its associated strings and modules.
Monitoring Platform User’s Guide for System Owners
Component Types
Component Description
Site : Represents the site level. Displays the energy produced by the site for the selected period.
Inverter : Represents an installed inverter. Displays the energy sum produced by the strings or modules connected to it.
String : Represents strings of modules. Displays the energy sum produced by the modules comprising the string.
Module : Represents a single module. Displays the energy produced by the module.
17
Monitoring Platform User’s Guide for System Owners
18
Component Options
For each component in the layout diagram, the following options can be selected by right-clicking the component:
Info: Provides a window with details table for the selected
component. For more information, see the Component Details
section.
Alerts: Redirect you to the alerts tab and displays all alerts related to the selected component.
Choose Charts: Select a chart type to display for this component. This action will redirect you to the Charts tab.
Collapse/Expand: Expand or collapse the selected components in the diagram, thus hiding or showing its underlying component hierarchy.
Large-scale site installations may contain thousands of modules. To enable simple site navigation, the SolarEdge monitoring platform enables the user to expand or collapse each hierarchical group of elements, one at a time. For example, expanding the inverter level shows all its connected modules.
View Device Screen (only for inverters): View the inverter LCD Display in real-time. For SetApp enabled inverters, the LCD display will present the current inverter status.
Figure 21: Component Options
Component Details
For each component or multiple components in the layout, e.g. inverters and modules, you can display its up-to-date details and performance data, such as the last power output measured.
To view component details:
1.
Select one or more components of the same type in the diagram (for example, only modules or only inverters). You can use
Ctrl + Click to perform multiple selections. Modules from different strings can be selected, as well as strings from different inverters. Alternatively, you can use the mouse to draw and drag a selection box around the components whose details you want to display.
2.
Right-click the selected components and select Info , or click on the toolbar
3.
Use the table information for near-real-time comparison of component performance, in order to troubleshoot faults and find their root cause, for example, checking which strings are producing less energy and locating the individual modules in those strings that may cause this situation.
Monitoring Platform User’s Guide for System Owners
Inverter Details
When the selected component is of inverter type, inverter-related information is displayed in the window, as shown below.
19
Figure 22: Inverter Details Window
System Data
The Inverter Details tab displays by defaultis the System data tab. This tab displayes the most recent readings taken by the inverter, including the date and time they were taken. The following parameters are measured and shown for the inverter:
Parameter
Serial Number
Description
A unique identifier of this component.
Name, Manufacturer, and
Model
DSP 2 Version,
Communication Board (CPU)
Version, DSP1 Version
Identifying information assigned to this component.
The firmware versions currently installed on the inverter.
Country Name, Country Code Inverter country settings.
I RCD [mA] RCD Current, measured in Amps.
Inverter Status
Last Isolation Value [KOhm]
Current production status of the inverter.
Inverter isolation value, measured in Kilo-Ohms.
P AC [W]
Power Limit [%]
V DC [V]
Inverter output power / inverter AC power, measured in Watts.
Inverter output power limit, measured in percentage.
Inverter DC voltage, measured in Volts.
Active Power [W]
Apparent Power [VA]
I AC [A]
I AC/DC [A]
V AC
Inverter active power, measured in Watts.
Inverter Apparent Power, measured in VA.
Inverter output current/inverter input current, measured in Amps.
Inverter out DC current, measured in Amps.
Inverter output voltage / inverter AC voltage, measured in Volts.
Monitoring Platform User’s Guide for System Owners
20
Running operations
This tab displays the operations currently being executed remotely on the inverter (e.g. reset, pairing).
Device screen
This tab presents the data currently shown on the LCD Display. For SetApp enabled inverters, the LCD display presents the current inverter status.
Errors
This tab allows you to view any errors related to the selected inverter.
Module details
When the selected component is of module type, module-related information is displayed in the window, as shown below.
Figure 23: Module Details Window
Monitoring Platform User’s Guide for System Owners
21
System data
The information window includes a single tab – System data. This tab provides the most recent module readings, including the date and time they were taken. The following parameters are measured and shown for the selected module:
Parameter
Serial Number
Name, Manufacturer, and Model
Description
A unique identifier of this component.
Identifying information assigned to this component.
Current [A]
Optimizer Voltage [V]
Power [W]
Voltage [V]
Module output current/inverter input current, measured in Amps.
Power optimizer output voltage, measured in Volts.
Module output power / inverter AC power, measured in Watts.
Module output voltage / inverter AC voltage, measured in Volts.
Actions in multiple components details window
When selecting multiple components, the following actions can be performed in the details window: a.
Enlarge.
Fit the details window to the entire screen b.
Export to Excel.
Save the component details in Excel format c.
Copy to Clipboard . Copy the data as text
Figure 24: Details window actions
Toolbar
The toolbar of the layout schematic provides options as described in the table below.
Icon Description
System components tree: Displays all components in the system according to their level. Click on a component to view its location in the layout schematic.
Show playback: dynamically visualizes the power production of a site during a selected time fragment
(either a day or a week).
Timeframe Selection list : Select a timeframe in which to display the energy production by each component in the layout.
Physical / Logical Layout : Displays the Physical or Logical Layout Schematic for the entire site.
Selected components remain selected when moving between the different layouts.
Hierarchy : Use the Hierarchy button to display the modules connected to each inverter.
Show/Hide Preview
: Shows or hides the Navigator tool, as described in the Navigator Tool section.
Refresh : To refresh the Layout Schematic and Component Detail table, click this icon.
Monitoring Platform User’s Guide for System Owners
22
Playback
The Playback dynamically visualizes the power production of a site during a selected time fragment (either a day or a week).
To open the playback viewer click Show Playback on the window’s toolbar. The playback viewer is displayed.
Figure 25: Playback Viewer
Choose Normal or Accelerated for the playback speed.
Click
Drag the slider along the timeline to focus on a chosen time fragment.
The resolution of the playback data is 15 minutes.
Monitoring Platform User’s Guide for System Owners
23
Support Contact Information
If you have technical problems concerning SolarEdge products, please contact us: https://www.solaredge.com/service/support
Before contact, make sure to have the following information at hand:
Model and serial number of the product in question.
The error indicated on the SetApp mobile application, LCD screen, on the monitoring platform, or as displayed by LEDs, if there is such an indication.
System configuration information, including the type and number of modules connected and the number and length of strings.
The communication method to the SolarEdge server, if the site is connected.
The product's software version as it appears in the ID status screen.
Monitoring Platform User’s Guide for System Owners
24
Monitoring Platform User’s Guide for System Owners
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement