1U Mixer-amps & Slave amps

A121U

A251U

S121

S251

Mixer-amp + USB/SD/FM 120W

Mixer-amp + USB/SD/FM 250W

Slave amp 250W

Slave amp 250W

952.903

952.905

952.908

952.911

User Manual

Features:



2 Mixer-amp models and 2 Slave versions



Transformer coupled output for 100V or 4-16 Ω operation



USB/SD/FM audio player on mixer-amp models



Compact 1U rack-mount format



Dual fan-cooled



High efficiency toroidal transformers www.adastra-pa.com

Introduction:

Thank you for choosing this Adastra 1U-series amplifier This product has been designed to offer reliable, high quality mixing for stage and/or studio applications with unfailing consistency. In order to gain the best results from this equipment and avoid damage through misuse, please read and follow these instructions and retain for future reference.

Warning:

To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.

If liquids are spilled on the surface, stop using immediately, allow unit to dry out and have checked by qualified personnel before further use.

Avoid impact, extreme pressure or heavy vibration to the unit.

There are no user serviceable parts inside the amplifier – refer all servicing to qualified service personnel.

Safety



Check that the mains lead is in good condition and that the supply voltage selector switch matches the supply voltage.



Ensure signal leads and speaker cable(s) are in good condition



Do not use the USB connector as a general purpose power source or charger.



Do not allow any foreign particles or liquids to enter the amplifier through the cooling vents



Do not cover or obstruct cooling vents or fan grilles.

Placement



Keep out of direct sunlight and away from heat sources.



Keep away from damp or dusty environments.



When rack-mounting, secure firmly in place and avoid positioning heavy items directly on top of the unit



Ensure adequate access to controls and connections and pay attention to cooling air-flow

Cleaning



Use a soft cloth with a neutral detergent to clean the housing as required



Use a soft brush to clear debris from the cooling vents and connectors



Do not use strong solvents for cleaning the unit.

Front Panel

1. Combo MIC1 input – Balanced XLR/6.3mm mic. input - channel

2. MIC1 – Volume control for MIC channel 1

3. MIC2 – Volume control for MIC channel 2

4. LOW – Bass EQ control for MIC channels

5. HIGH – Treble EQ control for MIC channels

6. VOX – Auto voice-over control for MIC channels

7. Cooling vents

8. LINE1 – Volume control for Line input 1

9. LINE2 – Volume control for Line input 2

10. USB/SD – Volume control for USB/SD/FM audio player

11. LOW – Bass EQ control for LINE and USB/SD channels

12. High – Treble EQ control for LINE and USB/SD channels

13. MASTER – Main output volume control

14. SD card slot and USB input

15. LED power, level and limit indicators

16. USB/SD/FM display

17. USB/SD/FM transport and mode controls

18. 3.5mm stereo input for LINE1 channel

19. POWER – Mains On/Off switch

Rear Panel

20. IEC mains inlet and integral fuse

21. Voltage selector 110/240Vac

22. Mono 6.3mm speaker jack outputs (4-16Ω only)

23. 100V speaker output terminals

24. Cooling Fans

25. OUTPUT – 2 x RCA line output

26. LINE1 + LINE2 – 2 x RCA line inputs

27. MIC1 + MIC 2 – 2 x balanced 6.3mm jack MIC inputs

Connection

The Adastra A1U-series mixer-amps and S1-series slave can drive EITHER 100V line OR 4-16 Ω speakers.

Both types of speaker should NOT be connected together to the same amplifier.

100V Line Speakers

100V line speakers must be connected using the “100V” and “COM” screw terminals (23) on the rear panel.

All 100V line wiring should be run with double-insulated cable rated to the max current for the system.

For example, in a 250W system @ 100Vmax, 250W/100V=2.5A, so the speaker cable should be rated to 2.5A minimum

Each speaker must be connected in a parallel chain and the total wattage for all speakers should not exceed 90% of the amplifier’s rated output. Please see the diagram below to show an example arrangement.

Cooling fans

Low Impedance Speakers

If standard low impedance (4 Ω, 8Ω or 16Ω) speakers are being used, these should be connected to the 6.3mm output sockets on the rear panel using quality speaker jack leads. Both of these outputs are fed from the same amplifier section, which is mono. The minimum impedance of the total speaker load connected to either or both of these sockets must be no lower than 4Ω.

The impedance is calculated using an inverse calculation as shown below.

_________1________ _________1________ _________1________

Impedance Speaker 1 + Impedance Speaker 2 = Overall Impedance

… therefore, for 2 speakers – each 8Ω impedance…

_1_

8 Ω +

_1_

8 Ω =

… so the overall impedance is 4Ω for both speakers connected in parallel.

The diagram below gives an example of this…

_1_

4 Ω

Inputs – Slave amplifiers

The S121 and S251 slave amplifiers accept a LINE IN via 2 x RCA connectors at the rear and the same signal can be sent out to further amplifiers from the LINE OUT pair of RCA connectors. Since the amplifier is mono, all stereo inputs are summed together.

Inputs – Mixer-amplifiers

A microphone can be connected to MIC1 channel by either 6.3mm jack or XLR to the front panel combo input. If required, there is also a 6.3mm jack connection on the rear panel for MIC1 channel. A further microphone can be connected to MIC2 channel via a 6.3mm jack on the rear panel.

Line inputs (e.g. CD, DVD, mp3 players) can be connected to LINE1 and LINE2 channels via pairs of RCA connectors on the rear panel. Alternatively, for LINE1 channel, a stereo 3.5mm socket on the front panel can be used instead – ideal for portable mp3 players etc.

There is also a USB type A connector and SD card slot on the front panel for playback of digital audio files stored on either USB pen drive or SD card.

The overall mix can be connected to further amplifiers via the OUTPUT pair of RCA connectors.

Operation

With all volume levels and VOX control turned down, connect the amplifier to the mains supply (ensure correct supply voltage) using a suitable IEC lead (as supplied) and switch POWER on.

H IGH and LOW EQ controls should be initially set to the vertical “12 o’clock” position.

If microphones are being used, turn up the MASTER control approximately half way and gradually increase MIC1 rotary level control whilst speaking into the microphone until the required volume is reached. Repeat for MIC2 volume control. Adjust HIGH and LOW EQ controls to alter the overall bass and treble response of both microphones as needed.

For any line level devices connected to line input channels, adjust the LINE1 and LINE2 level controls in the same way as for the microphone channels. Overall tone of the line inputs (including the USB/SD/FM player) can be adjusted via the HIGH and LOW controls.

For the USB/SD/FM player, pressing MODE toggles between the USB device, SD card and FM tuner as a sound source. Turning the USB/SD level control increases the level of the playback through the amplifier. The transport controls are as follows…

• • • •

Control

PRE NEXT PLAY MODE

USB

CH -

Previous track

CH+

Next track

PAUSE

Toggle Play/Pause

SD card

FM tuner Search down Search up Halt search

Toggle USB/SD/FM

The player status is indicated by a small backlit LCD screen to the immediate left of the transport buttons.

For MIC channels priority, increasing the VOX control will cause the level of playback through the LINE or

USB/SD/FM channels will be reduced when speaking into MIC1 or MIC2. Adjust this control to achieve the required amount of “ducking” of the other channels when MIC channels are used.

Model

Power supply

Output: RMS @ 4Ω

Mic input front

Mic inputs rear

Line input front

Line inputs rear

Mic controls

Line controls

USB/SD/FM player controls

LED indicators

Line output

Speaker outputs: 4Ω - 16Ω

Speaker outputs: 100V line

Dimensions

Weight

SPECIFICATIONS

A121U A251U S121

Switchable 110/240Vac, 50/60Hz (IEC)

120W 250W

MIC1 combo connector (XLR/jack)

120W

N/A

MIC1 & MIC2 6.3mm jacks

LINE1 stereo mini jack 3.5mm

LINE1 & LINE2 RCA (pairs)

MIC1 & MIC2 Levels, Low/High EQ, VOX

LINE1, LINE2, USB/SD/FM Levels, Low/High

N/A

N/A

N/A

N/A

N/A

Play/pause, PRE (CH -), NEXT (CH +), MODE N/A

On, -24/18/12/6/0dB, Limit

RCA (L+R) with Master volume control

2 x 6.3mm jack (4 ohms min)

7.8kg

Com/100V screw terminals

483 x 44 x 325mm (1U)

8.4kg 7.5kg

S251

250W

N/A

N/A

N/A

N/A

N/A

N/A

N/A

8.0kg

Troubleshooting

No power LED on control panel

Power LED is on but no other LEDs and no output

Power light and output LEDs lighting but no output

USB/SD player will not play audio from media

Output is very loud or LIMIT LED is on constantly

Output is working but at very low level

Feedback (loud squealing or howling from mics)

Amplifier is getting very hot

Ensure IEC lead is in good condition and connected properly

Ensure mains outlet voltage is same as voltage selector

Check mains inlet fuse

Ensure POWER switch is on

Check input signals and condition of input connection leads

Check MASTER, MIC or LINE controls are not turned fully down

Turn down VOX control

Check speaker leads are in good condition and connected properly

Check speakers are working (test on another amp if available)

Press PLAY on transport controls

Check memory device is connected properly (remove and re-insert)

Check file types

– standard compressed digital audio files required

Check memory device works on a PC or Mac for standard playback

Check level of input signal is not too high

Reduce channel volume and EQ settings

Reduce MASTER level until LIMIT light stops flashing

Ensure Hi-Z line level input(s) not connected via MIC1 or MIC2

Check input audio source level is not too low

Increase channel volume and EQ settings if turned down

Increase MASTER level

Check for quiet recording of media files on USB / SD card

Face microphone away from speakers and monitors

Reduce channel volume and EQ settings

Reduce MASTER level

Make sure fans are working properly and not obstructed

Ensure cooling vents are clear from debris and dust

Check that 4Ω or 8Ω speakers are not connected to 100V terminals

Ensure total 100V speaker wattage is not more than amplifier rating

Ensure that 100V and 4Ω or 8Ω speakers are not both connected

Ensure that total load across speaker jack outputs is not less than 4Ω

Note: for further troubleshooting, refer equipment to qualified service personnel for testing

© Adastra 2011