STMicroelectronics STM32C0316-DK User Manual
The STMicroelectronics STM32C0316-DK is a feature-rich development board that enables engineers to evaluate the capabilities of the STM32C031C6 MCU. With its triple STM32 package footprints, on-board 32768 Hz clock generator, and various user LEDs and buttons, the STM32C0316-DK provides a versatile platform for developing and testing applications.
Tangazo
Tangazo
UM2969
User manual
Discovery kit with STM32C031C6 MCU
Introduction
The goal of the STM32C0316-DK Discovery kit is to provide alternative features to the corresponding NUCLEO-C031C6 board.
All 20 pins common to all STM32C0 Series microcontrollers are user ‑ accessible. The user can override the SWD debug pins by disconnecting the debug probe. The 5-way analog rock switch and LED can be overridden with a slide switch to be taken over by the user. All the pins are accessible through the DIP28 connector. Headers are not provided to let the user choose the header type. The 32768 Hz on ‑ board 1 ‑ pin clock generator for RTC can be cut with a slide switch.
The kit helps migrate from 8 ‑ bit to STM32C0 Series microcontrollers, and between STM32C0 Series and STM32G0 Series microcontrollers. The DIP28 pinout is designed to be as compatible as possible with the ATMEGA328 8 ‑ bit microcontroller. The
LQFP48 footprint is compatible with STM32G031/071/0B1 Series microcontrollers. The UFQFPN20 footprint is compatible with
STM32C01 Series microcontrollers. The WLCSP20 footprint is compatible with STM32G051 Series microcontrollers.
The STM32C031C6 Series microcontroller can be tested over its operating range. The 5.0 to 3.3 V regulator bypass itself when its source goes lower than 3.3 V. The debug probe level shifters adjust the debug signal levels to the target microcontroller supply voltage.
Figure 1. STM32C0316-DK boards top and bottom views
Pictures are not contractual.
UM2969 - Rev 1 - January 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1
Note:
UM2969
Features
Features
•
•
•
•
•
•
•
•
•
• STM32C031C6 Arm ® Cortex ® ‑ M0+ core-based microcontroller with 32 Kbytes of Flash memory and
12 Kbytes of RAM, in an LQFP48 package
Board reference design triple STM32 package footprints: LQFP48, UFQFPN20, and WLCSP20
32768 Hz on-board clock generator
1 user LED and 2 power LEDs
Reset push-button
5 ‑ way joystick using a single ADC input pin
Slide switch to conveniently disconnect embedded user demonstration components
Board connectors:
– USB Micro-B for 5 V power
– STMod+ connector
– Bluetooth ® (HC05, 115200 bps) as a simple wireless serial adapter
– Not ‑ fitted DIP28 compatible extension connectors
– STDC14 debug connector for third ‑ party debug probes
– On-board both side pads for BTB card edge connector
– Standalone STLINK-V3MINIE debugger/programmer tiny probe for STM32 microcontrollers
Comprehensive free software libraries and examples available with the STM32Cube MCU Package
Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench ® , MDK-ARM, and STM32CubeIDE
Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2969 - Rev 1 page 2/26
2
2.1
UM2969
Ordering information
Ordering information
datasheet and reference manual of the target microcontroller.
Order code
STM32C0316-DK
•
•
Table 1. List of available products
Board reference
MB1716
MB1762
1. Mother board
2. STLINK-V3MINIE tiny probe
Codification
The meaning of the codification is explained in Table 2
.
Target STM32
STM32C031C6T6
STM32C0XXY-DK
STM32C0
XX
Y
DK
Table 2. Codification explanation
Description
MCU series in STM32 32-bit Arm Cortex MCUs
MCU product line in the series
•
STM32 Flash memory size:
6 for 32 Kbytes
Discovery kit
Example: STM32C0316-DK
STM32C0 Series
STM32C0x1 product line
32 Kbytes
Discovery kit
UM2969 - Rev 1 page 3/26
3
3.1
Note:
3.2
UM2969
Development environment
Development environment
•
•
System requirements
Multi ‑ OS support: Windows ® 10, Linux ® 64-bit, or macOS ®
USB Type-A or USB Type-C ® to Micro-B cable macOS ® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux ® is a registered trademark of Linus Torvalds.
All other trademarks are the property of their respective owners.
•
•
•
Development toolchains
IAR Systems ® - IAR Embedded Workbench ®
Keil ® - MDK-ARM
STMicroelectronics - STM32CubeIDE
1. On Windows ® only.
3.3
Demonstration software
The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board microcontroller, is preloaded in the STM32 Flash memory for easy demonstration of the device peripherals in standalone mode. The latest versions of the demonstration source code and associated documentation can be downloaded from www.st.com
.
UM2969 - Rev 1 page 4/26
4
Conventions
provides the conventions used for the ON and OFF settings in the present document.
Convention
Jumper JPx ON
Jumper JPx OFF
Jumper JPx [1-2]
Solder bridge SBx ON
Solder bridge SBx OFF
Resistor Rx ON
Resistor Rx OFF
Capacitor Cx ON
Capacitor Cx OFF
Table 3. ON/OFF convention
Definition
Jumper fitted
Jumper not fitted
Jumper fitted between Pin 1 and Pin 2
SBx connections closed by 0 Ω resistor
SBx connections left open
Resistor soldered
Resistor not soldered
Capacitor soldered
Capacitor not soldered
UM2969
Conventions
UM2969 - Rev 1 page 5/26
5
5.1
UM2969
Quick start
Quick start
Before installing and using the product, accept the Evaluation Product License Agreement from the www.st.com/ epla webpage. For more information on the STM32C0316-DK Discovery kit and demonstration software, visit the
STM32C0316-DK product webpage.
Getting started
Follow the sequence below to configure the STM32C0316-DK Discovery kit and launch the demonstration
application (Refer to Figure 2
and Figure 3 in UM2910 for component location):
1.
Check the position of the SW1 slide switch on the board (Refer to
).
2.
For the correct identification of the device interfaces from the host PC and before connecting the board, install the STLINK-V3MINIE tiny probe USB driver, available on the www.st.com
website.
3.
Connect the stand-alone tiny probe CN2 connector and the STM32C0316-DK mother board CN4 connector by BTB card edge connector.
4.
To power the tiny probe, connect it to a PC with a USB Type-A USB Type-C ® cable through the CN1 USB connector of this board.
5.
To power the STM32C0316-DK mother board, connect it to a PC or a 5V adapter with a Type-A to Micro-B
USB cable through the CN3 USB power connector of the board.
6.
Then, the LD1 COM red LED on the tiny probe lights up and the LD2 red LED on the mother board lights up.
7.
Press the B2 joystick and observe the blinking of the LD1 green LED.
8.
The demonstration software, as well as other software examples for exploring STM32C0 features, is available on the STM32C0316-DK product webpage.
Jumper
SW1
Table 4. Jumper configuration
Definition Position
IDD ON
Demo
RXSL
32K
ON
ON
OFF
Comment
For STM32C0 current measurement
Connect demonstration 3.3 V power
Connect VCP_RX
32 KHz oscillator enable
1. Default jumper state is in bold.
UM2969 - Rev 1 page 6/26
6
6.1
UM2969
Hardware layout and configuration
Hardware layout and configuration
and Figure 3 show the location of the features. The mechanical dimensions of the board are shown in
.
PCB layout
Figure 2. PCB layout (Top view)
USB Micro-B
(CN3)
User LED
(LD1)
5V LED
(LD2)
3V3 LED
(LD3)
STMod+
(CN1)
STM32C031 microcontroller
(U2)
Joystick
(B2)
STDC14 connector
(CN5)
Pads for
BTB connector (Top)
(CN4)
Reset button
(B1)
Slide switch
(SW1)
Bluetooth
®
connector
(CN2)
Pad for GND
UM2969 - Rev 1 page 7/26
UM2969 - Rev 1
Pads for BTB connector (Bottom)
(CN4)
Figure 3. PCB layout (Bottom view)
UM2969
PCB layout
Pad for GND
Extension connectors
(CN6/CN7)
page 8/26
6.2
Mechanical drawing
Figure 4. Board mechanical drawing (In millimeters)
UM2969
Mechanical drawing
6.3
STLINK-V3MINIE
STLINK-V3MINIE is a standalone debugging and programming tiny probe with an extended voltage range for
STM32 microcontrollers. The board number is MB1762.
The STLINK-V3MINIE can connect to the target STM32 through:
•
•
STDC14 connectivity with a flat cable (ref. SAMTEC # FFSD-07-D-05.90-01-N-R)
AVX10 provided BTB (board ‑ to ‑ board) card edge connector. (ref. 009159010061911)
For further details, refer to the user manual STLINK-V3MINIE debugger/programmer tiny probe for STM32 microcontrollers ( UM2910 ).
UM2969 - Rev 1 page 9/26
6.4
6.5
6.5.1
6.5.2
UM2969
Power supply
Power supply
The STM32C0316-DK Discovery kit is designed to be powered using the CN3 USB power connector.
The input voltage is a 5V power rail from the CN3 USB power connector. The LD56100DPU33R power regulator output voltage is 3.3 V. If a supply input voltage lower than 3.3V is provided on the 5V rail, the LD56100DPU33R
LDO goes in bypass mode.
It is also possible to access the same 5V power rail through the DIP28 or STMod+ connectors.
Board functions
LEDs
The onboard LED functions are described in
.
LED
Function1
Function 2
Function 3
Function 4
Push-buttons
B1 Reset/user button
This push-button is connected to NRST (PF2-NRST) and is used to reset the STM32C0 Series microcontroller or to generate a user event.
B2 joystick
This joystick is a 5 ‑ way rock switch using a single ADC input pin (PA4). Push-in “Select” can be used as a digital
user button and EXTI wakeup interrupt. The joystick position for the ADC value refers to Table 6 .
Joystick position
Select
Down
Left
Right
Up
No key pressed
Table 5. LED functions
LD1 green user LED LD2 red 5 V power trail LED
ON if PA5 = 0
OFF if PA5 = 1
LED cut if SW1 Demo is OFF
PA5 = TIM1.CH1 (AF5)
ON if 5V present
OFF otherwise
Brightness varies with voltage
[2.0~5V]
-
LD3 blue 3.3 V power trail monitor LED
ON if 3.3V present
OFF otherwise
-
-
Table 6. Joystick position versus ADC value
Measurement ratio
0
0.20
0.40
0.61
0.80
1.0
ADC value (In volts)
0
0.67
1.32
2.01
2.65
3.3
UM2969 - Rev 1 page 10/26
6.5.3
6.5.4
UM2969
Board functions
Slide switch
The SW1 slide switch is used to connect or disconnect the STM32C0 microcontroller consumption (IDD), demo
3.3 V power (Demo), VCP_RX (RXSL), and 32 KHz on ‑ board oscillator (32K).
Slide switch
SW1
Definition
IDD
Demo
RXSL
32K
1. Default slide switch state is in bold
Table 7. Slide ‑ switch configuration
ON
OFF
ON
OFF
ON
OFF
OFF
ON
STM32C0 is powered by 3V3 voltage.
An ammeter must be connected on SB1 to measure the STM32C0 current and power the MCU.
Connect the demo 3.3 V power (User LED and key connected).
Disconnect demo 3.3 V power.
Connect VCP_RX (STLink and BT share the same STM32C0 RX).
Disconnect VCP_RX.
Oscillator 32768 Hz enable
Oscillator 32768 Hz disable
MCU package
The STM32C0316-DK Discovery kit supports 3 different packages as crossover or migration facility. It includes U2
STM32C031C6T6 in TQFP48 package (Default soldered), U3 STM32C011F6U6 in UFQFPN20 package, and U1
STM32G051F8Y6 in WLCSP20 package.
UM2969 - Rev 1 page 11/26
6.5.5
UM2969
Board functions
Solder bridges
The solder bridges (SBx) are located on the top layer of the STM32C0316-DK mother board. Their configuration appears in
. Package SB is used in the 20 ‑ pin configuration.
Solder bridge control
Solder bridge
SB2
Package selection
Power selection
SB3
SB4
SB5
SB8
SB9
SB1
SB6
SB7
1. Default solder bridge state is in bold
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
Table 8. Solder bridge configuration
Description
CN6 pin 12 is connected to PC15 for the 20 ‑ pin package.
CN6 pin 12 is connected to PD1 for the 48 ‑ pin package.
CN6 pin 13 is connected to PA5 for the 20 ‑ pin package.
CN6 pin 13 is connected to PD2 for the 48 ‑ pin package.
CN6 pin 11 is connected to PC14 for the 20 ‑ pin package.
CN6 pin 11 is connected to PD0 for the 48 ‑ pin package.
CN6 pin 14 is connected to PA4 for the 20 ‑ pin package.
CN6 pin 14 is connected to PD3 for the 48 ‑ pin package
CN6 pin 5 is connected to PA14 for the 20 ‑ pin package.
CN6 pin 5 is connected to PC7 for the 48 ‑ pin package.
CN6 pin 4 is connected to PA13 for the 20 ‑ pin package.
CN6 pin 4 is connected to PC6 for the 48 ‑ pin package.
Disable slide switch for 3V3 voltage ON/OFF.
Enable slide switch for 3V3 voltage ON/OFF.
5V power is selected for the CN2 connector.
5V power is not selected for the CN2 connector.
3V3 power is selected for the CN2 connector.
3V3 power is not selected for the CN2 connector.
UM2969 - Rev 1 page 12/26
7
7.1
7.2
UM2969
Board connectors
Board connectors
CN1 STMod+ connector
The STMod+ connector is available on the STM32C0316-DK Discovery kit to support flexibility in small form factor applications. The STMod+ connector extends UART and spare I/Os for different peripheral expansions. It is
Connector
CN1
Table 9. CN1 STMod+ connector
17
18
19
20
14
15
16
9
10
11
12
13
Pin number
1
2
3
4
5
6
7
8
GPIO
5V
GND
GPIO
GPIO
GPIO
GPIO
GPIO
SDA
GPIO
GPIO
GPIO
Pin name
CTS
TX
RX
RTS
GND
5V
SCL
GPIO
PD2
PB11/PA12
PC14
PC15
PA4
PA5
-
-
PB0
PA6
PD1
PD0
Port
PA0
PA2
PA3
PA1
-
-
PB10/PA11
PA7
CN2 Bluetooth
®
connector
The Bluetooth
®
connector is available on the STM32C0316-DK Discovery kit to support Bluetooth
®
HC-05/06 dongles. It is a 4 ‑ pin header with 5 V (or 3.3 V with solder bridge) supply rail and UART RX/TX link. It is described
. This serial interface is shared with STLink-VCP and goes to the same USART pins. SW1 slide switch is used to disconnect STLink VCP to Target MCU RX to avoid conflict. When using STLink-VCP remove HC-05
Pin number
1
2
3
4
Table 10. CN2 Bluetooth ® connector
Pin name
VDD
GND
BT ‑ TX
BT ‑ RX
Description
5V or 3V3 power selection by SB6 and
SB7
Power supply
UART transmit data
UART receive data
UM2969 - Rev 1 page 13/26
7.3
7.4
UM2969
CN3 USB Micro-B power connector
CN3 USB Micro-B power connector
The USB Micro-B power connector is used to connect 5 V rail power from PC for board power supply. The USB device function operates only with STM32G0B1 QFP48 device configuration.
Terminal
1
2
3
Table 11. CN3 USB Micro-B connector
Description
V
BUS
(Power)
DM
DP
Terminal
4
5
6 - 11
CN4 on ‑ board pads to BTB card edge connector
Table 12. CN4 on-board pads to BTB card edge connector
Side
TOP
BOTTOM
Pin number
1
2
9
10
7
8
5
6
3
4
1. Do not connect on target.
2. NC means not required for SWD connection.
3. Output power source for STLINK-V3MINIE.
Pin description
5V
SWDIO
SWCLK
GND
VCP_RX
VCP_TX
NRST
Description
ID
GND
Shield
Type
S
-
I
S
I
O
I/O
I
-
S
UM2969 - Rev 1 page 14/26
7.5
UM2969
CN5 STDC14 connector
CN5 STDC14 connector
The CN5 STDC14 connector allows the connection to the STLINK-V3MINIE tiny probe through the SWD protocol, respecting (from pins 3 to 12) the ARM10 pinout (Arm ® Cortex ® debug connector). But it also advantageously provides two UART signals for the Virtual COM port. The related pinout for the STDC14 connector is listed in
Figure 5. CN5 STDC14 connector
STDC14 pin number
1
2
5
6
3
4
7
8
9
10
11
12
13
14
1. Do not connect on target.
2. Input for STLINK-V3MINIE.
3. NC means not required for SWD connection.
ARM10 pin number
-
-
3
4
1
2
5
6
7
8
-
-
9
10
Table 13. CN5 STDC14 connector pinout
Description
3V3
SWDIO
GND
SWCLK
GND
NC
NC
NC
NC
NRST
VCP_RX
VCP_TX
Type
S
S
O
I/O
S
I
S
-
-
-
I
O
I
-
UM2969 - Rev 1 page 15/26
7.6
UM2969
CN6/CN7 DIP28 extension connectors
CN6/CN7 DIP28 extension connectors
The extension connectors are available on the STM32C0316-DK Discovery kit to support flexibility in user applications. They form a DIP28 which tries to be as close as possible to ATMEGA328 footprint and includes
UART, SPI, I 2
C, ADCs, and spare I/Os for different peripheral expansion. It is described in Table 14. CN6/CN7
Connector
CN6
CN7
Table 14. CN6/CN7 DIP28 extension connectors
4
5
6
7
8
11
12
13
14
1
2
3
12
13
14
9
10
11
Pin number
1
2
3
4
9
10
7
8
5
6
GPIO
GPIO
GPIO
GPIO
ADC/SCL
ADC/SDA
GPIO
GPIO
ADC
ADC
GND
NC
Pin name
NRST
RX
TX
GPIO
GPIO
GPIO
5V
GND
NC
NC
5V
SCK
MISO
MOSI
NSS
GPIO
PC14/PD0
PC15/PD1
PA5/PD2
PA4/PD3
PB10/PA11
PB11/PA12
PA9
PA10
PA5
PA4
-
-
-
PA1
PA6
PA7
PB0
PB8
Port
-
PA3
PA2
PA13/PC6
PA14/PC7
PA0
-
-
-
-
UM2969 - Rev 1 page 16/26
8
UM2969
Port mapping for different packages
-
PCB trace name
PA10
USBD_N
USBD_P
PA13
PA14
PB0
STM32_TX1
STM32_RX1
PA5
PA6
PA7
PA8
PA9
PA0
PA1
PA2
PA3
PA4
SCL
SDA
PC6
PC7
PD0
PD1
PD2
PD3
NRST
PC14
PC15
1. Uses simulated I 2 C.
Port mapping for different packages
Table 15. CN6/CN7 DIP28 extension connectors
STM32
Key AF
CTS2
RTS2/SCK1
TX2
RX2
ADC_IN.x
ADC_IN.x
MISO1
MOSI1
GPIO
BL
BL
USB
USB
SWDIO
SWCLK/BOOT0
NSS1
TX1
RX1
SCL1
SDA1
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
PF2/NRST
OSC23_IN
OSC32_OUT
STM32C031C6T6
QFP48
PA5
PA6
PA7
PA8
PA9
PA0
PA1
PA2
PA3
PA4
PA10
PA11
PA12
PA13
PA14/PA15
PB0/PB1/PB2
PB3/PB4/PB5/PB6
PB7/PB8
PB10
PC6
PC7
PD0
PD1
PD2
PD3
PF2/NRST
PC14_OSC32IN/PB9
PC15_OSC32OUT
STM32G051F8Y6
WLCSP20
STM32C011F6U6
QFN20
PA5
PA6
PA7
N/A
N/A
PA0
PA1
PA2
PA3
PA4
N/A
N/A
N/A
PA13
PA14
PB0/PB1/PB2/PA8 PA8
PB3/PB4/PB5/PB6 PB6
PB7/PB8 PB7
N/A
N/A
N/A
PA13
PA14
PA5
PA6
PA7
N/A
N/A
PA0
PA1
PA2
PA3
PA4
PA11/PA9
PA12/PA10
N/A
N/A
N/A
N/A
N/A
N/A
PF2/NRST
PC14_OSC32IN
PC15_OSC32OUT
PA11/PA9
PA12/PA10
N/A
N/A
N/A
N/A
N/A
N/A
PF2/NRST
PC14_OSC32IN
PC15_OSC32OUT
UM2969 - Rev 1 page 17/26
9
9.1
9.2
9.2.1
9.3
9.3.1
9.3.2
UM2969
STM32C0316-DK board information
STM32C0316-DK board information
Product marking
The stickers located on the top or bottom side of the PCB provide product information:
• Product order code and product identification for the first sticker
• Board reference with revision, and serial number for the second sticker
On the first sticker, the first line provides the product order code, and the second line the product identification.
On the second sticker, the first line has the following format: “MBxxxx-Variant-yzz”, where “MBxxxx” is the board reference, “Variant” (optional) identifies the mounting variant when several exist, "y" is the PCB revision and "zz" is the assembly revision, for example B01. The second line shows the board serial number used for traceability.
Evaluation tools marked as “ES” or “E” are not yet qualified and therefore not ready to be used as reference design or in production. Any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering sample tools as reference designs or in production.
“E” or “ES” marking examples of location:
•
•
On the targeted STM32 that is soldered on the board (For an illustration of STM32 marking, refer to the
STM32 datasheet “Package information” paragraph at the www.st.com
website).
Next to the evaluation tool ordering part number that is stuck or silk-screen printed on the board.
Some boards feature a specific STM32 device version, which allows the operation of any bundled commercial stack/library available. This STM32 device shows a "U" marking option at the end of the standard part number and is not available for sales.
In order to use the same commercial stack in his application, a developer may need to purchase a part number specific to this stack/library. The price of those part numbers includes the stack/library royalties.
STM32C0316-DK product history
Product identification DK32C0316$KT1
This product identification is based on the MB1716 revision A-03 and MB1762 revision B-01 boards.
It embeds the STM32C031C6T6 microcontroller with revision code "A". The limitations of this revision are detailed in the errata sheet STM32C031 device errata ( ES0568 ).
Product limitations
No limitation identified for this product identification.
Board revision history
Board MB1716 revision A-03
The revision A-03 is the initial release of the MB1716 board.
Board limitation
No limitation identified for this board revision.
Board MB1762 revision B-01
The revision B-01 is the initial release of the MB1762 board.
Board limitation
No limitation identified for this board revision.
UM2969 - Rev 1 page 18/26
UM2969
Federal Communications Commission (FCC) and Innovation, Science and Economic Development Canada (ISED) Compliance Statements
10
10.1
Note:
10.2
Federal Communications Commission (FCC) and Innovation,
Science and Economic Development Canada (ISED) Compliance
Statements
FCC Compliance Statement
Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part 15.21
Any changes or modifications to this equipment not expressly approved by STMicroelectronics may cause harmful interference and void the user's authority to operate this equipment.
Part 15.105
•
•
•
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use only shielded cables.
Responsible party (in the USA)
Terry Blanchard
Americas Region Legal | Group Vice President and Regional Legal Counsel, The Americas
STMicroelectronics, Inc.
750 Canyon Drive | Suite 300 | Coppell, Texas 75019
USA
Telephone: +1 972-466-7845
ISED Compliance Statement
This device complies with FCC and ISED Canada RF radiation exposure limits set forth for general population for mobile application (uncontrolled exposure). This device must not be collocated or operating in conjunction with any other antenna or transmitter.
Compliance Statement
Notice: This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
ISED Canada ICES-003 Compliance Label: CAN ICES-3 (B) / NMB-3 (B).
UM2969 - Rev 1 page 19/26
UM2969
ISED Compliance Statement
Déclaration de conformité
Avis: Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Étiquette de conformité à la NMB-003 d'ISDE Canada : CAN ICES-3 (B) / NMB-3 (B).
UM2969 - Rev 1 page 20/26
Revision history
Date
28-Jan-2022
Table 16. Document revision history
Revision
1 Initial release.
Changes
UM2969
UM2969 - Rev 1 page 21/26
UM2969
Contents
Contents
UM2969 - Rev 1 page 22/26
UM2969
Contents
10 Federal Communications Commission (FCC) and Innovation, Science and Economic
UM2969 - Rev 1 page 23/26
UM2969
List of tables
List of tables
UM2969 - Rev 1 page 24/26
UM2969
List of figures
List of figures
UM2969 - Rev 1 page 25/26
UM2969
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
UM2969 - Rev 1 page 26/26
Pakua
Kiungo cha umma kime sasishwa
Kiungo cha umma kwa mazungumzo yako kimesasishwa. You may view and manage your chat links after registration here.
Kiungo cha umma cha hati
Tangazo
