DO NOT REMOVE this label until the refrigerator has been leveled.
Please follow all instructions for leveling your refrigerator.
CROSLEY __ Installation Instructions* for French Door Bottom Freezer/Refrigerator
*Please refer to your Use & Care Guide for more details.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
Doors final adjustment using the adjustable lower hinge (select models, if necessary):
4 WARNING
To avoid electric shock, which can cause death or severe personal injury, do not connect your refrigerator to an electrical power source until you have completed Step 2 of these instructions.
2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.
\
Plastic Water
Tubing -to.
Steel
Clamp
1 Open doors to 90 degrees.
2 Remove screw.
3 Lift the door while adjusting the washer.
To raise the door: rotate washer clockwise.
If you need to remove the doors to get your refrigerator into the house, please refer to “Removing Doors” in the Use & Care Guide, These installation instructions are provided only as a possible customer option.
Frigidaire recommends that you use a service or kitchen contracting professional to install your refrigerator.
. Remove plastic cap from water valve inlet and discard cap.
Brass
Corpression
Nut
To lower the door: rotate washer counterclockwise.
4 Replace the screw, ensuring it is between the spokes of the hinge washer. Screw will not be tight, just insert until it is flush with the hinge.
i NOTE md IMPORTANT ) CAUTION
. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (*4 inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO
NOT overtighten. See Figure 1.
Ferrule
(Sleeve)
Copper waterline
Water Valve
Bracket
@® Loosen or Remove
Screw
& NOTE
(\ if after adjusting doors higher the door makes a popping/clicking sound, remove screw and replace with the
If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 2.
Open
go]
degrees | |)
|
Need) |
Bottom of Door |
Remove Screw
Raising/Lowering Door longer one provided.
If you are installing your refrigerator
wi
ithout connecting it to a water
supply, make sure the ice maker's
power switch is turned Off (see the se & Care Guide for more details). e Shifting the refrigerator from side to side
may damage flooring. _
® Do not block the toe grille on the lower _ front of your refrigerator. Sufficient air cir- culation is essential for proper operation.
Copper-.water -line
Valve. Inlet
Water Valve from ‘household . water supply.
4 Leveling Freezer Drawer (if necessary)
1 Preparing For Installation
5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.
6. Coil excess water supply line (copper tubing only), about 21/2 turns, behind refrigerator
(include. enough: tubing “in loop ‘to allow
: moving refrigerator..out.for cleaning.)
Figure 1
t NOTE move Hx -»
LZ
ZB
SS
Remove Hex
Head Drawer
Be sure to coordinate site preparation and installation with your kitchen contractor.
Include these minimum guidelines in your site preparation: i NOTE e Choose a place near a grounded electrical outlet. e Do not use an extension cord or an adapter plug.
e Avoid direct sunlight and close proximity to a range, Please call 1-800-944-5044 if you,
dishwasher or other heat source. need assistance with this installation. e Floor should be level and able to support. a fully loaded refrigerator. e The refrigerator’s Ice Dispenser requires water supply access. e Plan for easy access to counter tops when removing food. e For complete access to drawers and freezer baskets, doors must be able to fully open.
° boad refrigerator from side of cabinet
4 CAUTION
Room temperatures below 55°F (13°C)
(oaling wollityrar
. e Do not run retaining straps over handles nor overtighten straps. | tom pressor. e Never use refrigerator handles to move the refrigerator. as shown and arrange coils so they do not vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and tighten any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm
(freezer ice maker) or set the ice maker’s On/
Off power switch to the “ON” position (fresh food ice maker).
ie NOTE
Y— Stainless
Steel water line
DO NOT remove center screw from freezer drawer. This is a factory adjustment.
1. Check gasket seal around top, bottom, and sides of freezer drawer.
2. If gasket is not sealed, open drawer and slightly loosen 4 drawer screws (2 on each side) to allow drawer to rotate.
3. Close drawer and recheck the seal on the gasket (A). Open the drawer grabbing by the sides in the center (B).
Be careful not to rotate the drawer.
Remove Hax
Head Drawer, Head Drawer
Screw,
| push Against
Freezer Drawer
é i yf Gtab Drawer
Al Center
From Both Sides
Th en
Pull Drawer Out
Allow the following clearances for ease of installation, proper air ; ; circulation, and plumbing and electrical connections: Sides & Top: °/s inch / Rear: 1 inch
Tighten 4 drawer screws.
Recheck gasket seal.
Install the toe grille by fitting into place.
4 a
2 Connect Water Supply
Before Installing The Water Supply Line, You Will Need: e Basic Tools: adjustable wrench, flat-blade screwdriver, and
Phillips™ screwdriver e Access to a household cold water line with water pressure between 30 and 100 psi.
« A water supply line made of %4 inch (6 mm) OD, copper or stainless steel tubing. To determine the length o tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximate ‘eet, so the
refrigerator can be moved ou for cleaning, |
fy WARNING
To avoid electric shock, which can cause death or_severe personal injury, disconnect the
necting a water supply
e shutoff valve to connect the water su ine to your i | household water system. DO NOT use Pe dlt-piercing type line to the refrigerator. shutoff valve.
« A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.
-
Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator.
Depending on your local/state building codes,
Frigidaire recommends for homes with existing valves its Smart Choice® water line kit
5305513409 (with a 6 ft. Stainless Steel Water
Line) and for homes without an existing valve,
Frigidaire recommends its Smart Choice water® line kit 5305510264 (with a 20 ft. Copper Water
Line with self-tapping saddle valve). Please refer Fi
to www. frigidaire.com for more information. igure
2
6 ft. Stainless Steel water line from household water supply
3 Level Refrigerator & Adjust Doors (if necessary)
Guidelines for final positioning of your refrigerator e All four corners of the cabinet must rest firmly on the floor.
5 Remove Internal Shipping Materials
Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material.
What’s Next?
Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator. e For important safety instructions and to learn how to operate your refrigerator, please read the entire Use & Care Guide. e You may want to start with the “Normal Operating Sights & Sounds” section of the Guide to learn what to expect during typical operation. e Please register your product. You can register online at www. frigidaire.com or you can simply send in the Registration Card.
44 CAUTION
To Avoid Property Damage: e Copper or Stainless Steel braided tubing is recommended for the wa- ter supply line. Water supply tubing made of 14 inch (6 mm) plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be respon- sible for any damage if plastic tubing is used for the supply line. e Do not reuse compression fitting or use thread seal tape. e DO NOT install water supply tubing in areas where temperatures fall below freezing. e Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is maintained and working properly. e The sides should tilt 4 inch (6 mm) from front to back (to ensure that doors close and seal properly). e« Doors should align with each other and be level.
Most of these conditions can be met by raising or lowering the adjustable front rollers.
To level the cabinet using the front rollers: the floor.
* Door
& &
Door
1 You can raise or lower each door. Use a 3/s inch socket | EE wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
2 Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable,
3 After unit is leveled, lower anti-tip leg until it contacts
Vi Installation Check List
Doors
D Handles are secure and tight
CD Door seals completely to cabinet on all sides
CZ Fresh food doors are level
Leveling
LD Refrigerator is level, side to side and tilted
¥4 inch (6 mm) front to back
LD Toe grille is properly attached to refrigerator
D Cabinet is sitting solid on all corners
Electrical Power
CD House power turned on
D Refrigerator plugged in
Ice Maker
Ci House water supply connected to refrigerator
D No water leaks present at all connections
CZ Ice Maker is turned ON.
Final Checks
LD Shipping material removed
LD Fresh Food and Freezer temperatures set
If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-800-944-9044 for assistance. P/N: 242227300