Genius D5123 manual
Genius D5123 is a digital camera that allows you to take still pictures and videos, with features like a built-in flash, macro function, and zoom capability. It has a user-friendly LCD screen for easy navigation and control over various settings. The device supports an SD card for storage, enabling you to capture and save your memories conveniently.
Anúncio
Anúncio
English
WEEE Warning Message
Symbol for Separate Collection in European Countries
This symbol indicates that this product is to be collected separately.
The following apply only to users in European countries: z This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste. z For more information, contact the retailer or the local authorities in charge of waste management.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
-1-
English
receiver is connected.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the
FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.
READ THIS FIRST
Notice:
1. Product design and specifications are subject to change without notice. This includes primary product specifications, software, software drivers, and user's manual. This User
Manual is a general reference guide for the product.
2. The product and accessories that come with your camera may be different from those described in this manual. This is due to the fact that different retailers often specify slightly different product inclusions and accessories to suit their market requirements, customer demographics, and geographical preferences. Products very often vary between retailers especially with accessories such as batteries, memory cards, cables, pouches, and language support. Occasionally a retailer will specify a unique product color, appearance, and internal memory capacity. Contact your dealer for precise product definition and included accessories.
3. The illustrations in this manual are for the purpose of explanation and may differ from the actual design of your camera.
4. The manufacturer assumes no liability for any errors or discrepancies in this user's manual.
5. For driver updates and revisions to this manual, please refer to our website www.geniusnet.com
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
WARNING
If foreign objects or water have entered the camera, turn the power
OFF and remove the batteries.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
-2-
English
If the camera has fallen or its case has been damaged, turn the
power OFF and remove the battery.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask retailer where you purchased it.
Use the specified batteries.
Use with any other type of batteries might cause explosion or influence the camera’s performance.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow, on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing injury.
Keep the batteries out of the reach of children.
Swallowing batteries might cause poisoning. If the battery is accidentally swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in a traffic accident.
CAUTION
If foreign objects or water have entered the camera, turn the power
OFF and remove the batteries.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to leak. If the internal fluid enters your eyes or comes into contact with your body or clothes, rinse with fresh water.
If the internal fluid has entered your eyes, consult a physician to receive treatment.
-3-
English
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of
continuous use.
The battery becomes hot during use. Touching a hot battery might cause burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and electric shock.
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions and the notes described below:
Use only the specified battery.
Avoid using the battery in extremely cold environments as low temperatures can shorten the battery life and reduce camera performance. Avoid using the batteries in extremely cold environments as low temperatures can shorten the batteries life and reduce camera performance. This low temperature will also influence alkaline batteries performance, therefore Ni- MH rechargeable batteries are highly recommended.
When you are using the new rechargeable batteries or a rechargeable battery that has not been used for an extended period of time (the batteries that passed the expiry date are exception) might affect the number of images that can be captured. Therefore, to maximize their performance and lifetime, we recommend that you fully charge the batteries and discharge them for at least one complete cycle before use.
The battery may feel warm after long period of continuous use of the camera or the flash.
This is normal and not a malfunction.
-4-
English
The camera may feel warm after long period of continuous use. This is normal and not a malfunction.
If the battery is not to be used for a long period of time, remove it from the camera to prevent leakage or corrosion.
If the batteries are not to be used for a long period of time, store it after no battery power left. If the battery is stored for a long time in a fully charged state, its performance may be impaired.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Never use batteries of different types (together) or mix old and new batteries.
Never use manganese batteries.
-5-
English
CONTENTS
INTRODUCING THE CAMERA _____________________________ 9
S
YSTEM REQUIREMENTS
___________________________________ 9
F
EATURES
_____________________________________________ 9
U
NPACKING
___________________________________________ 10
A
BOUT THE CAMERA
_____________________________________ 10
Front view __________________________________________ 11
Top view ____________________________________________ 11
Back view___________________________________________ 11
Bottom view _________________________________________ 12
Right view __________________________________________ 12
GETTING STARTED ____________________________________ 13
I
NSERTING THE BATTERIES
_________________________________ 13
I
NSERTING AN
SD
CARD
___________________________________ 14
T
URNING ON FOR THE FIRST TIME
____________________________ 14
C
HANGING MODES
_______________________________________ 14
B
EFORE YOU START
______________________________________ 15
Setting the date and time _______________________________ 15
Setting the language __________________________________ 16
T
AKING YOUR FIRST STILL PICTURE
___________________________ 16
S
HOOTING YOUR FIRST VIDEO
_______________________________ 16
C
ONNECTING TO A COMPUTER
_______________________________ 17
USING THE CAMERA ___________________________________ 18
U
SING THE CAMERA BUTTONS
_______________________________ 18
A
BOUT THE
LED
S
_______________________________________ 19
U
SING THE
LCD ________________________________________ 19
P
HOTO MODE
__________________________________________ 20
Photo mode icons ____________________________________ 20
Setting the flash ______________________________________ 22
Using the macro function _______________________________ 22
-6-
English
Using the zoom function________________________________ 22
Possible number of shots (still image) _____________________ 23
V
IDEO MODE
___________________________________________ 24
Video mode icons_____________________________________ 24
Using the macro function _______________________________ 25
Using the zoom function________________________________ 25
Possible recording time / sec (video clip) ___________________ 25
P
LAYBACK MODE
________________________________________ 26
Playback mode icons __________________________________ 26
Viewing pictures and videos_____________________________ 27
Displaying file information ______________________________ 27
Using thumbnail mode _________________________________ 28
Viewing a slide show __________________________________ 28
USB
MODE
____________________________________________ 28
Storage device mode __________________________________ 28
Webcam mode_______________________________________ 28
USING THE SETUP MENUS ______________________________ 29
P
ICTURE MENU
_________________________________________ 29
Picture quality _______________________________________ 29
Exposure adjustment (EV) ______________________________ 29
Self timer ___________________________________________ 30
Burst snapshot _______________________________________ 30
White balance _______________________________________ 30
Time stamp _________________________________________ 31
V
IDEO MENU
___________________________________________ 31
Video Resolution _____________________________________ 31
Exposure adjustment (EV) ______________________________ 32
White balance _______________________________________ 32
P
LAYBACK MENU
________________________________________ 33
Delete______________________________________________ 33
Delete All ___________________________________________ 33
Protect _____________________________________________ 34
Print _______________________________________________ 34
-7-
English
S
ETUP MENU
___________________________________________ 34
Date and time________________________________________ 34
Language ___________________________________________ 34
Format storage_______________________________________ 35
TV output ___________________________________________ 35
USB connection ______________________________________ 35
Auto power off _______________________________________ 36
Light frequency ______________________________________ 36
Default setting _______________________________________ 36
System info _________________________________________ 37
INSTALLING SOFTWARE AND DRIVERS ___________________ 38
D
RIVERS
_____________________________________________ 38
Mass Storage ________________________________________ 38
Web camera_________________________________________ 38
P
RESTO
!
V
IDEO
W
ORKS
6 _________________________________ 39
P
RESTO
!
M
R
.
P
HOTO
3 ___________________________________ 39
APPENDIX ____________________________________________ 40
S
PECIFICATIONS
________________________________________ 40
T
ROUBLESHOOTING
______________________________________ 41
-8-
English
Introducing the camera
Read this section to learn about the features and functions of the camera. This chapter also covers system requirements, package contents, and descriptions of the hardware components.
System requirements
The camera requires a host PC with the following specifications: z Windows® XP, 2000, ME, 98SE operating system z z z z z
Intel® Pentium III 500 MHz CPU or higher
At least 256 MB of RAM
Standard USB 1.1 port or better
4 x speed CD-ROM drive or better
At least 200 MB of available disk space
NOTE
A USB 1.1 port will enable you to transfer files to and from your PC, but transfer speeds are much faster with a USB 2.0 port.
Features
The camera is packed full of features and functions including: z 3-in-1 functions: Digital still camera, Digital video camera and Web camera. z z
True 5.1 mega pixel CMOS sensor
Maximum 12.0 mega pixels resolution z z
2.0” TFT LCD display
4X digital zoom z Slide option z Direct print function
-9-
English
Unpacking
All the following items should be present in the camera package. If any item is missing or displays damaged, contact your dealer immediately.
Digital camera
Pouch
Wrist strap AAA batteries x2 USB/AV Out cable
CD-ROM
(driver and application software)
User manual
About the camera
Refer to the following illustrations to familiarize yourself with the buttons and controls of the camera.
-10-
Front view
Strap
Eyelet
Top view
Shutter button
English
Sliding power (ON/ OFF) cover
Flash
Self-timer
LED
Lens
Microphone
Back view
Busy LED
Macro LED
LCD screen
Playback / display button
Menu button
Previous button
OK /Set button
Next button
-11-
Bottom view
Right view
Battery compartment
SD card slot
English
Tripod mounting hole
Macro/
Landscape switch
USB port
-12-
English
Getting started
Read this section to learn how to start using the camera. This section covers only basic functions such as inserting the battery or memory cards, turning it on, and making preliminary settings. See later chapters for details about advanced functions.
Inserting the batteries
The camera is powered by two AAA alkaline batteries.
NOTE
Install the batteries exactly as described here. Ensure that the polarity of the batteries is correct. Installing the batteries incorrectly could cause damage to the camera and possibly start a fire.
1. Open the battery compartment door.
2. Insert the battery as shown.
3. Close the battery compartment door.
-13-
English
Inserting an SD card
An SD card can be installed in the camera to provide additional storage space for still images, video clips, or other files.
Install an SD card at the bottom of the camera as shown in the illustration. Make sure the gold contacts are facing up towards the LCD, as shown.
To remove the SD card, gently push it into the card slot and release. The card pops out. Slide out the card.
Turning on for the first time
Slide the power cover sideways as shown in the picture to switch the camera on.
Slide the power cover sideways as shown to switch the camera off.
When the camera is switched on, the Busy LED will flash red, and an image will appear on the LCD display.
Changing modes
The camera can operate in four modes:
Photo, Video, Playback, and Setup.
Long press and hold the MENU button to view the mode menu. Use the Previous or Next buttons to select a mode and press OK/Set button to confirm your selection.
-14-
Photo
English
Video
Playback
Setup
Before you start
Before you use your camera there are some basic settings to configure, which are described here.
Setting the date and time
To set the date and time:
1. Turn the camera on as described in “Turning on for the first time”.
2. Press and hold the MENU button to display the main menu screen.
3. Use the Previous or Next buttons to select the setup menu, as shown. Press OK/Set button to confirm your selection.
4. Use the Previous or Next buttons to highlight the Date & Time Setting option. Press OK/Set button to confirm.
5. Use the Previous or Next buttons to alter values in the selected field. Press the Playback/Display button to move between fields such as year, month, date and so on.
The year, month, hours, date, and minute format fields are available for modification in this manner.
6. Press OK/Set button to save the new setting.
Press MENU to exit the menu without making any changes.
-15-
English
Setting the language
To set the language:
1. Turn the camera on as described in “Turning on for the first time”.
2. Press and hold the MENU button to display the main menu screen.
3. Use the Previous or Next buttons to select the setup menu. Press OK/Set button to confirm your selection.
4. Use the Previous or Next buttons to highlight the
Language option. Press OK/Set button to confirm.
5. Use the Previous or Next buttons to select the desired language.
6. Press OK/Set button to save the new setting, or press MENU to exit the menu without making any changes.
Taking your first still picture
Before taking your first still picture, make sure you read “Before you start”.
To take a picture:
1. Turn the camera on and make sure it is in photo mode.
2. Use the LCD to frame the picture.
3. Press the shutter button to capture the picture.
The picture is automatically saved with a unique filename.
Shooting your first video
Before shooting your first video, ensure you have read “Before you start”.
To shoot a video:
1. Turn on the camera and change the mode to video mode.
2. Use the LCD to frame your video.
3. Press the shutter button to begin recording.
4. Press the shutter button again to stop recording.
The video is automatically saved with a unique file name.
-16-
English
Connecting to a computer
Read this section to learn how to connect the camera to a computer to transfer files or to use the camera as a PC camera for web-conferences.
Connect the camera to a computer using the USB port and the USB cable provided as shown.
See “USB connection” for more information about connecting to a computer.
-17-
English
Using the camera
Read this section to learn how to use the camera.
Using the camera buttons
All buttons are located on the top and the back of the camera. See the table below for a description of each button’s function.
Button Name Function
Display z
Press to remove icons from the LCD.
Press again to restore them. z
Press and hold the button to enter playback mode.
Menu
Previous /
Next button
& Zoom in / out
OK/Set button z Press to display the Picture menu,
Playback menu, or Video menu. z
Press and hold to display the Mode menu. z
Use Previous to zoom in Photo or Video modes. z
Use Next to zoom out in Photo or Video modes. z
Use Previous to increase image size or view the previous image in Playback mode. z
Use Next to decrease image size or view the next image in Playback mode. z
In Photo mode, press to turn on the flash.
z
In Playback mode, press to display thumbnail images. z
In OSD menus, press to select a highlighted menu option.
Macro/
Landscape switch
Toggle between Macro and landscape picture modes.
-18-
English
Shutter z
Press to capture a picture in Photo mode z
Press to start/stop video recording in
Video mode. z
Press to enlarge/reduce image size in
Playback mode.
About the LEDs
The following tables explain the meaning of the LEDs.
● blink once
★ blink lasting
◇ light lasting
Photo mode
Self-timer LED Red
Busy LED Red
Power on Self-capture
Shutter button
Flash charging
Macro
●
●
★
N/A N/A N/A
N/A
●
★
N/A
N/A N/A N/A N/A
◇
Macro LED Green
Using the LCD
Use the LCD to compose your pictures and videos, review pictures and videos stored in memory, and navigate the menu system. Icons shown the current configurations are also displayed on the LCD.
Customizing the LCD
If you don’t want to display icons on the LCD, press the Display button to remove the icons from the screen.
When you turn the camera on, the LCD displays icons and pictures by default. Press the Display button once to turn off the icons and display pictures only. Press the
Display button again to display everything again.
-19-
English
Photo mode
Use Photo mode to capture still pictures and store them in internal memory or on an
SD card. The camera is in Photo mode when the Photo mode icon is displayed.
Photo mode icons
Use the following picture to familiarize yourself with the Photo mode icons and symbols.
1
2
3 4
13
12
11 10
9
8 7
6
See the following table for a description of each icon and symbol.
Icon Description
1
Indicates battery status.
2
Indicates stabilization of hand shaking.
3
Indicates macro mode.
4
Indicates Photo mode.
5
-20-
English
Icon
5
Date display.
Description
6
7
8
Memory indicator, SD card or internal memory.
Counter to display the number of available shots using current settings.
Shows current resolution
Indicates burst or single mode photo
9
Timer indicator
10
Flash mode indicator.
11
Indicates zoom ratio.
12
13
Zoom indicator shows the current zoom status graphically.
-21-
English
Setting the flash
There are three different flash modes. To switch between flash modes, press the
OK/Set button. An icon indicates the current flash setting.
Icon Description
Flash is turned off
Forced flash, flash is always on.
Automatic flash, fires only when needed.
Using the macro function
The macro function enables you to capture images of subjects very close to the lens.
In macro mode you can focus on subjects as close as 15cm. When not in macro mode the minimum distance is 16cm. Use macro mode for subjects 15-16cm from the camera.
To switch the macro function on, use the macro switch on the side of the camera. An icon displays to indicate macro mode. The macro function can be used in both
Video mode and Photo mode.
Using the zoom function
The camera is equipped with a 4x digital zoom. The zoom function works in Photo mode and in Video mode.
Press the Previous button to zoom in on a subject (get closer to it). Press the Next button to zoom out from the subject (move away from it).
The bar on the left of the screen indicates the zoom status. The zoom ratio is also represented in figures under the zoom bar.
-22-
English
Possible number of shots (still image)
The table below shows the approximate number of shots that you can take at each setting based on internal memory and SD memory card.
Resolution
Internal SD Memory Card
32MB 64MB 128MB 256MB 512MB 1GB
4048 x 3040
12MP
2592 x 1944
5MP
22 44
65
130
88
260
176
520
352
1040
704
2080
2048 x 1536
3MP
90
180 360 720 1440 2880
1280 x 960
1.3MP
165
330 660 1320 2640 5280 z
The above data shows the standard testing results. The actual capacity varies according to the shooting conditions and settings.
-23-
English
Video mode
Use Video mode to capture video and store it in internal memory or on an SD card.
The camera is in Video mode when the Video mode icon is displayed.
Video mode icons
Use the following picture to familiarize yourself with the Video mode icons and symbols.
1
2
3
4
8
7
See the table below for a description of each icon and symbol.
Icon Description
6
5
1
Indicates battery status.
2
3
4
Indicates Video mode.
Date display.
-24-
English
Icon
5
Description
Memory indicator, SD card or internal memory.
6
7
Indicates image resolution.
C (CIF) =320x240, V (VGA) = 640x480
Indicates ratio.
8
Zoom indicator shows the current zoom status graphically.
Using the macro function
Refer to “Using the macro function” in Photo mode.
Using the zoom function
Refer to “Using the zoom function” in Photo mode.
Possible recording time / sec (video clip)
SD card capacity
Image size
32
MB
64
MB
128
MB
256
MB
640 x
480
5 min.
02 sec.
15 min.
13 sec.
20 min.
36 sec.
24 min.
36 sec.
512
MB
50 min.
32 sec.
1GB
2 hours
15 min.
47 sec.
320 3 hours
8 min. 20 min. 31 min. 45 min. 97 min. x 15 min.
59 sec 53 sec.
33 sec.
31 sec.
49 sec.
240 29 sec.
* The data shows the standard testing results. The actual capacity varies according to the shooting conditions and settings
-25-
English
Playback mode
Use Playback mode to review all the pictures and videos stored in your camera.
Playback mode icons
Refer to the following picture to familiarize yourself with the Playback mode icons and symbols.
1
Photo Playback
2
Video Playback
3 4
5
7 6
9
8
7
See the table below for a description of each icon and symbol.
Icon
6
Description
1
2
3
Indicates that the displayed image can be zoomed and moved. Press the shutter button to enable zooming and moving.
Indicates the current picture is tagged for printing.
See section “Print” for more details.
The playback bar indicates whether current video is paused, playing, being fast-forwarded, or rewound.
Press the Shutter button and OK/Set button to operate the playback bar.
Indicates the current file is protected from deletion.
4
-26-
English
Icon Description
Time and date of photograph or video.
5
6
7
8
Shows the total length of video when paused, or the current position during playing back.
Shows current position of video. The circle moves from left to right as the video plays.
Current photo number/total number of photos and videos on internal memory or current memory card.
9 Photo resolution.
Viewing pictures and videos
To view pictures and videos:
Turn the camera on and ensure that it is in playback mode. The most recent picture is displayed on the screen.
Use Previous/Next button to move through the image and video files stored in memory.
Press OK/Set button to view thumbnails of the videos and images.
To play videos: z z z z
Press the shutter button to play videos
Press the shutter button again to fast forward through the video
Press the shutter button again to pause the video.
Press the OK/Set button to rewind the video.
Displaying file information
Basic information is displayed by default on each image or video when viewed in
Playback mode. To switch this information on or off, press the Display button.
Press the display button a second time to remove all file information from the screen.
Press this button a third time to display basic information again.
-27-
English
NOTE
Video file can’t remove all file information from the screen.
Using thumbnail mode
By default, each image is displayed full size in playback mode, but you can display six thumbnail images on the screen.
To use thumbnail mode:
1. Turn the camera on and ensure that it is in playback mode. The most recent picture is displayed on the screen.
2. Press the OK/Set button to display six thumbnail images on the screen.
3. Use Previous/Next to highlight an image.
4. Press the OK/Set button to display the highlighted image on screen full size.
Viewing a slide show
The camera includes a slide show function. A slide show displays each image in turn with a predefined delay between each picture.
To view a slide show:
1. Turn the camera on and ensure that it is in playback mode. The most recent picture is displayed on the screen.
2. Press the menu button to display the playback menu.
3. Use Previous/Next to highlight the slide show option in the menu.
4. Press the OK/Set button to start the slide show.
The images stored in memory are displayed consecutively. You can stop the slide show at any time by pressing any button.
USB mode
Use USB mode to connect to a PC. Before connecting to a PC, see “Installing the software and drivers”.
The camera can be set to act as a USB mass storage device or a webcam when connected to a PC using the USB cable.
Storage device mode
When set as a USB mass storage device, the camera displays as a removable drive in Windows Explorer. You can drag and drop files to and from the new removable drives just like any other drive.
Webcam mode
When set to webcam, the camera can be used with Windows XP to capture photographs, or used with third-party software such as instant messenger clients to send live video over the Internet.
See also “Connecting to a computer” and “USB connection”.
-28-
English
Using the setup menus
Read this section to learn how to configure your camera and use advanced features.
Picture menu
The picture menu displays when the camera is in Photo mode and the menu button is pressed. The picture menu is available in Photo mode only.
Picture quality
Use the picture quality option to set the size of the captured image. Bigger images contain more detail and therefore use more memory space.
To set the image size:
1. Turn the camera on and ensure that it is in Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Picture
Quality option.
4. Use OK/Set button to select a setting: 1, 3, 5, or
12 M (Mega pixels).
5. Press the menu button again to exit the menu.
NOTE
This option is only available in Photo mode.
Exposure adjustment (EV)
Use the exposure EV setting to change the exposure for your pictures. Usually this value is set to zero, but you might want to increase the exposure to light up a subject with strong back lighting, or decrease the exposure if taking a picture of something very bright.
To set EV:
1. Turn the camera on and ensure that it is in
Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Exposure
Value option.
4. Press OK/Set button to slide through the scale.
At the highest setting, press OK/Set button again to start from the lowest value.
5. Press the menu button again to exit the menu.
-29-
English
Self timer
The self-timer option allows a photo to be taken a specified interval after the shutter is pressed. It is useful when taking self-portraits or group photos. You can set the interval to OFF, or 10, 15, 20 seconds.
To set the self timer interval:
1. Turn the camera on and ensure that it is in Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Self timer option.
4. Use OK/Set button to select a setting: OFF, 10, 15, and 20.
5. Press the menu button again to exit the menu.
6. Press the shutter to take the photograph. The LED on the front of the camera flashes before the photograph is taken, and the interval is reset to OFF.
NOTE
This option is only available in Photo mode.
Burst snapshot
The burst snapshot option allows you to take a series of three photographs very quickly with one press of the shutter. It is useful to take series shots of moving objects and for artistic effect.
To set burst snapshot:
1. Turn the camera on and ensure that it is in Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Burst Snapshot option.
4. Use OK/Set button to select a setting: Single or
Burst.
5. Press the menu button again to exit the menu.
NOTE
This option is only available in Photo mode.
White balance
Use the white balance option to correct color for different lighting conditions. When white balance is set to automatic, the camera automatically compensates for different lighting conditions. You can also set white balance to sunlight, cloudy, tungsten, or one of two kinds of fluorescent light.
-30-
English
To set the white balance:
1. Turn the camera on and ensure that it is in Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the White Balance option.
4. Use OK/Set button to select a setting: AWB
(automatic), Sunny, Cloudy, Tungsten,
Fluorescent 1 or Fluorescent 2.
5. Press the menu button again to exit the menu.
Time stamp
Use the time stamp function to print a date on captured images. Turn the camera on and ensure that it is in Photo mode.
To set the time stamp function:
1. Turn the camera on and ensure that it is in Photo mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Time Stamp option.
4. Use OK/Set button to select a setting: OFF, Date
Only, or Date & Time.
5. Press the menu button again to exit the menu.
NOTE
This option is only available in Photo mode.
Video menu
The Video menu displays when the camera is in Video mode and the menu button is pressed. The Video menu is available in Video mode only.
Video Resolution
Use the resolution option to determine the resolution of the captured video. The larger screen size requires more memory storage space.
To set video resolution:
1. Turn the camera on and ensure that it is in Video mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Video
Resolution option.
4. Use OK/Set button to select a setting: 320x240 or 640x480.
5. Press the menu button again to exit the menu.
-31-
English
Exposure adjustment (EV)
Use the exposure EV setting to change the exposure for your pictures. Usually this value is set to zero, but you might want to increase the exposure to light up a subject with strong back lighting, or decrease the exposure if taking a picture of something very bright.
To set EV:
1. Turn the camera on and ensure that it is in
Video mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Exposure
Value option.
4. Press OK/Set button to slide through the scale.
At the highest setting, press OK/Set button again to start from the lowest value.
5. Press the menu button again to exit the menu.
White balance
Use the white balance option to correct color for different lighting conditions. When white balance is set to automatic, the camera automatically compensates for different lighting conditions. You can also set white balance to sunlight, cloudy, tungsten, or one of two kinds of fluorescent light.
To set the white balance:
1. Turn the camera on and ensure that it is in Video mode.
2. Press the menu button.
3. Use Previous/Next to highlight the White Balance option.
4. Use OK/Set button to select a setting: AWB
(automatic), Sunny, Cloudy, Tungsten,
Fluorescent 1 or Fluorescent 2.
5. Press the menu button again to exit the menu.
-32-
English
Playback menu
Use the playback menu to manage the files stored in the camera memory or on an SD card.
Delete
Use the delete function to delete the file.
To delete files:
1. Turn the camera on and ensure that it is in
Playback mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Delete option.
4. Press OK/Set button to delete. A dialog prompts to confirm.
5. Press OK/Set button for yes or Menu for no.
NOTE
Once deleted, files cannot be recovered so make sure you have a backup before you delete.
Protected files cannot be deleted. See “Protect” for more details about file protection.
Delete All
Use the delete all function to delete all files on the current memory card or internal memory.
To delete all files:
1. Turn the camera on and ensure that it is in
Playback mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Delete All option.
4. Press OK/Set button to delete.
5. A dialog asks you to confirm. Press OK/Set button for yes or Menu for no.
NOTE
Once deleted, files cannot be recovered so make sure you have a backup before you delete.
Protected cannot be deleted. See “Protect” for more details about file
protection.
-33-
English
Protect
Use the protect option to protect files from being accidentally deleted.
To protect a file or files:
1. Turn the camera on and ensure that it is in
Playback mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Protect option.
4. Press OK/Set button to select a setting: ON or
OFF.
5. Press the menu button again to exit the menu.
NOTE
Protected files cannot be deleted. To delete a protected file, you must first unprotect it.
Use the DPOF (Digital Print Order Format) function to tag pictures stored in your memory card with print information. You can tag all pictures to be printed or just the current picture.
DPOF requires a memory card. When all images to be printed are tagged, remove the memory card and take it to a photographic shop for printing, or use it with a DPOF compatible printer.
To print images:
1. Turn the camera on and ensure that it is in
Playback mode.
2. Press the menu button.
3. Use Previous/Next to highlight the Print option.
4. Use OK/Set button to select a setting: ON or OFF. The DPOF information is stored.
5. Press the menu button again to exit the menu.
Setup menu
The setup menu is accessible from any mode and is used to configure miscellaneous camera functions.
Date and time
See “Setting the date and time”.
Language
See “Setting the language”.
-34-
English
Format storage
Formatting the storage erases all files on the current memory card or internal memory.
To format the current memory card or internal memory:
1. Turn the camera on and ensure that it is in Settings mode.
2. Use Previous/Next to highlight the Format Storage option.
3. Press OK/Set button to format the current memory card.
4. Press OK/Set button to confirm or Menu to cancel.
NOTE
Protected files are deleted if you format the memory card or internal memory. Make sure you have a back up copy of any files you want to keep.
TV output
Use the TV option to set the TV output system for the area.
To change the TV output settings:
1. Turn the camera on and ensure that it is in
Settings mode.
2. Use Previous/Next to highlight the TV Output option.
3. Press OK/Set button to select a setting: NTSC or
PAL.
USB connection
The camera can be set to act as a USB mass storage device or a webcam when connected to a PC using the USB cable.
To change the USB settings:
1. Turn the camera on and ensure that it is in
Settings mode.
2. Use Previous/Next to highlight the Mass Storage
/ PC Cam option.
3. Press OK/Set button to confirm your selection.
-35-
English
Auto power off
Use the auto power off function to automatically switch the camera off after a period of inactivity to save power.
To set the power saving function:
1. Turn the camera on and ensure that it is in
Settings mode.
2. Use Previous/Next to highlight the Power Saving option.
3. Press OK/Set button to select a setting: Off, 1
MIN, 3 MIN, or 5 MIN.
Light frequency
The light frequency setting allows you to prevent flickering light caused by the local power supply’s frequency. For more information contact the energy supplier in the area.
To set the light frequency:
1. Turn the camera on and ensure that it is in
Settings mode.
2. Use Previous/Next to highlight the Light
Frequency option.
3. Press OK/Set button to select an option: 50 or
60.
Default setting
Use the default setting option to reset all settings to the factory default.
To reset factory default settings:
1. Turn the camera on and ensure that it is in Settings mode.
2. Use Previous/Next to highlight the Default Setting option.
3. Press OK/Set button to restore factory defaults. You are prompted to confirm the reset.
4. Press OK/Set button to confirm or Menu to cancel.
-36-
System info
This displays the firmware version.
To display the system information:
1. Turn the camera on and ensure that it is in Settings mode.
2. Use Previous/Next to highlight the System info option.
3. Press OK/Set button to display the information.
English
-37-
English
Installing software and drivers
Read this section to learn how to install drivers and software for the camera.
Drivers
You can use the “Mass Storage” and “PC Camera” functions of the camera on the PC.
Mass Storage
The digital camera offers Mass Storage function as a card reader device. You can treat this digital camera as an SD device
You will only need to install a driver for the camera if your operating system is
Windows 98SE. Windows XP/ME/2000 are plug and play operating systems and do not require a driver to be manually loaded.
When the driver has been installed and the camera is connected, the camera memory and any installed SD card displays as Mass Storage in Windows Explorer. Files can be dragged and dropped in the same way as an ordinary disk.
Web camera
You will need to install a driver for the camera to use as a PC or Web Camera in all
Windows operating systems (Windows XP/ME/2000/98SE).
NOTE
Driver installation is required for all operating systems.
The digital camera can be used as a Web camera.
Follow the instructions below:
Insert the supplied CD-ROM in the CD-ROM drive.
1. If the CD-ROM doesn’t automatically boot, use Windows Explorer to execute the
InstallMgr.exe file in the root directory.
2. Click the install button to install the driver.
3. Follow the on-screen instructions.
4. Click Finish to restart the computer and finish the camera driver installation.
-38-
English
Presto! Video Works 6
Presto! Video Works 6 is an advanced software application for editing video.
To install Presto! Video Works 6:
1. Insert the supplied CD-ROM in the CD-ROM drive.
2. If the CD-ROM doesn’t automatically boot, use Windows Explorer to execute the
InstallMgr.exe file in the root directory.
3. Click the install button to begin the installation process and follow the on-screen instructions.
More information about Presto! Video Works 6 can be found in the help files when the application is started.
Presto! Mr. Photo 3
Presto! Mr. Photo 3 is an advanced photo editing software application.
To install Presto! Mr. Photo 3:
1. Insert the supplied CD-ROM in the CD-ROM drive.
2. If the CD-ROM doesn’t automatically boot, use Windows Explorer to execute the
InstallMgr.exe file in the root directory.
3. Click the install button to begin the installation process and follow the on-screen instructions.
More information about Presto! Mr. Photo 3 can be found in the help files when the application is started.
-39-
English
Appendix
Specifications
Item Description
Imaging sensor 1/2.5” CMOS 5.17 Mega pixel sensor
Active pixels
Storage media
5 Mega pixels
Built-in 32 MB Flash memory
SD card (up to 1 GB)
Sensor sensitivity Auto
Lens
Focus range
Fixed focus lens, F/3.2, f=7.36mm
Normal: 1.5m ~ infinity
Macro: 15 ~ 16 cm
Still image
Movie clips
Formats: JPEG (DCF, EXIF) DPOF,
Resolution: 1280 x 960, 2048 x 1536, 2560 x 1920,
4032 x 3024 (firmware interpolation)
AVI (Motion JPEG), sound available
Movie: 320 x 240 max 15fps or 640 x 480 max 8fps
PC cam: 320 x 240 max 30fps or 640 x 480 max 15fps
LCD TFT screen 2” TFT LCD, 480 x 240 pixels
White balance
Off/ Auto Force/ Force
Auto/Sunny/Cloudy/Tungsten/Fluorescent 1/Fluorescent 2
EV compensation -2.0 EV ~ +2.0 EV (in 0.5 EV steps)
Self timer
PC interface
Off, 10 seconds, 15 seconds, 20 seconds
USB 1.1 for PC camera and mass storage
-40-
English
Item Description
Shutter Electronic shutter, 1/4 ~ 1/2000 seconds
Auto power off
Power supply
Off, 1min, 3mins, or 5mins (user definable)
2X AAA alkaline batteries
Dimension
Weight
87 x 57 x 25 mm
<75± 3 g without batteries
Troubleshooting
Power Supply
Symptom Cause
The power does not come on.
The power cuts out during use.
The batteries run out quickly.
The batteries or camera feels warm.
Measure
The batteries are not loaded.
The batteries are exhausted.
Load the batteries correctly.
Replace with a new set of batteries.
The camera was left unattended and unused, so the auto powers off cuts it off.
Turn the power back on.
The batteries are exhausted.
Replace with a new set of batteries.
It is being used in extreme low temperature.
Many shots are being captured in dark places inside, requiring flash.
Long period of continuous use of the camera or the flash.
-41-
English
Symptom Cause
The batteries are running low.
The power is not on.
The camera is not in Photo mode.
Measure
Replace with a new set of batteries.
Turn the power on.
Press the Menu button for two seconds to select photo mode.
The internal memory or memory card does not have any free capacity.
Insert a new memory card, or delete unwanted files.
Even if I press the shutter button, the camera does not shoot.
End of memory card life. Insert a new memory card.
The flash is recharging.
The memory card is unrecognized by the camera.
Wait until the status LED is off.
Format the memory card in this camera before its first use or when it was used other than this camera.
The auto power off function is activated.
The memory card is write-protected.
Turn the power on again.
Remove the write-protection.
Images do not appear on the
LCD monitor.
The power is not on. Turn the power on.
The lens cover is not open.
Open the lens cover.
The flash does not fire. The flash cannot recharge.
The flash is set to off.
Press Set button to switch to Automatic flash and
Force Flash.
The image is too dark.
The image was captured in a dark place while set to no flash.
Set the flash to something other than flash off mode.
-42-
English
Playback
Symptom Cause
Cannot playback.
It is not set to playback mode.
Measure
Press the Menu button for two seconds to select playback mode.
The contents of memory card cannot be replayed.
You played back a memory card that was not formatted by this device.
Insert a memory card that was formatted and stored on by this device.
Files cannot be deleted.
You played back a memory card that was not formatted by this device.
Loaded a card that was formatted and stored on by this device.
Cannot format a memory card.
The memory card is write-protected.
Remove the write-protection.
End of memory card life. Load a new memory card.
Other Problems
Symptom
Cannot load the memory card.
Cause
The card is facing the wrong way.
Measure
Insert correctly.
Even when the camera’s
The battery is Replace with a new set of buttons are pressed, it running low. batteries. does not operate.
About connecting to your computer/software
Symptom
Cause
Measure
Cannot download images.
The free space on the hard disk in your computer may be insufficient.
Check whether the hard disk has a space for running Windows, and if the drive for loading image files has a capacity at least that of the memory card inserted in the camera.
-43-
Symptom
Cause
The USB driver is not installed (for
Windows 98/98SE).
Measure
Install USB driver.
English
-44-
Download
Link público atualizado
O link público para seu chat foi atualizado. Você pode visualizar e gerenciar seus links de chat após o registro aqui.
Link público do documento
Anúncio