DEC/DES6800 CVBS/SDI Converter

USER MANUAL

Product Information

Model:

Version:

DEC/DES6800 CVBS/SDI Converter

V010000

Release Date: March 28th, 2008

Company

OSEE TECHNOLOGY CO., LTD.

Contact Information

Address:

No.22 Building, No.68 zone, Beiqing Road, Haidian District,

Beijing, China

Post Code: 100094

Tel:

(+86) 010-62434168

Fax:

(+86) 010-62434169 http://www.osee-dig.com/

Web:

E-mail:

[email protected]

Contents

Chapter 1 Introduction .......................................................................................... 1  

Overview ............................................................................................................................................ 1  

General Description of Modules ........................................................................................................ 1  

Features .............................................................................................................................................. 1  

Introduction to Module ...................................................................................................................... 2  

The Front Part of Module ........................................................................................................... 2  

Back Connector .......................................................................................................................... 4  

Back Connector for DEC/DES6800N ........................................................................................ 4  

Signal Flow Chart .............................................................................................................................. 5  

Chapter 2 Installation ........................................................................................... 5  

Overview ............................................................................................................................................ 5  

Maximum Power Dissipation for Frame ............................................................................................ 6  

Unpacking the Module ....................................................................................................................... 6  

Preparation for Installation ......................................................................................................... 6  

Check Packing List .................................................................................................................... 6  

Module Installation ............................................................................................................................ 6  

Signal Connections .................................................................................................................... 7  

Module Removal ........................................................................................................................ 7  

Chapter 3 Operation and Control ......................................................................... 8  

User Control and Operating Instruction ............................................................................................. 8  

Pay attention to the followings when configuration ......................................................................... 14  

Composite in Video Path Processing: ...................................................................................... 14  

Decoded Video Path Processing: .............................................................................................. 15  

Video Timing and Freeze Controls .......................................................................................... 15  

Freeze Mode ............................................................................................................................. 15  

OSD Mode ............................................................................................................................... 15  

Set the Jumper .................................................................................................................................. 15  

Chapter 4 Specifications ..................................................................................... 16  

Analog Video Input .......................................................................................................................... 16  

SDI Video Processing ...................................................................................................................... 16  

SDI Video Output ............................................................................................................................. 16  

Phase ................................................................................................................................................ 16  

Chapter 5 Warranty for osee

product ................................................................ 17  

What the warranty covers: ............................................................................................................... 17  

What the warranty does not cover: ................................................................................................... 17

DEC/DES6800 CVBS/SDI Converter

Chapter 1 Introduction

Overview

In this chapter the following modules are introduced ：

DEC6800N ： Supporting one composite loop output, two SDI output and two SDI outputs with OSD.

DES6800N ： Supporting one composite loop output, one REF loop input, one REF loop output, two SDI output and two SDI outputs with OSD.

The above modules can be installed in the 6800N Series frame.

General Description of Modules

The DEC/DES6800N is a compact 12-bit decoder and can convert NTSC, PAL and composite signal into 4:2:2 SDI component signal with broadcasting quality.

The module can handle the signal like the satellite feed and microwave which contains a plenty of noise.

The DES6800 has a built-in synchronizer.

The DEC/DES6800N is controlled by switch on the front panel. The table1-1 gives a general description of modules.

Table 1-1

DEC/DES6800N

Module Description

DEC6800N Has one composite loop output, two SDI outputs, and two SDI outputs with OSD

DES6800N Has one composite loop output, one REF loop input, one REF loop output, two SDI outputs and two SDI outputs with OSD.

Features

T he DEC/DES6800 has the following features:

 4 oversampling 12-bit A/D converter

 Auto-detection on NTSC/PAL for input

 AGC/ACC

 Full functional processing amplifier

 Progressive VBI processing

 Built-in test pattern generator (color bar and black burst)

 EDH insertion

 OSD can be overlaid to the output

 NTSC/PAL reference input

 Built-in synchronizer

DEC/DES6800 CVBS/SDI Converter - 1 -

FCC Caution

:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Introduction to Module

The Front Part of Module

Figure 1-1

DEC/DES6800N

Note: Table 1-1 Introduction to the switch and status LED indicator. Refer to Chapter Three for detailed instructions on switch and status LED indicator.

DEC/DES6800 CVBS/SDI Converter - 2 -

Figure 1-2 Switch and Status LED Indicator on the Front Part of DEC/DES6800

Table 1-2 ： Status Indicator and Its Function

CONFIG

(yellow)

POWER

(green)

ERROR

(red)

Off

On

Off

On

Module is in normal operating mode.

Module is initializing or initialized error.

No power to module

Normal operation, module is powered.

WARNING(red)

BANK MARK

(yellow)

Bank 0

BANK MARK1

(yellow) Bank1

625(green)

AUTO(green)

525(green)

GENLOCK(yellow)

On continuously No signal present on input.

Flashing No reference or input signal line rate does not match

Off

On the reference.

Off when module runs in disorder

On/Off combination indicates which bank is selected

(described in Table 3)

Off

On

On continuously Valid 625 video input is present.

Off Standard 625 is not selected or under auto-detection,

Flashing

On no valid 625 standard is detected.

Standard 625 is detected and no valid 625 video input is present.

Auto standard is selected

Off Auto standard is not selected

On continuously Valid 525 video input is present.

Off Standard 525 is not selected or under auto-detection, no valid 525 standard is detected.

Flashing

Off

On

Standard 525 is selected and no valid 525 video input is present.

Reference genlock mode is not selected

Reference genlock mode is selected

DEC/DES6800 CVBS/SDI Converter - 3 -

FREEZE (green)

TSG(yellow)

Back Connector

Off

On

Off

On

Freeze is disabled

Freeze is enabled

TSG output is disabled

TSG output is enabled

Figure 1-3

6800N-U2 frame Back Connector

Back Connector for DEC/DES6800N

Figure 1-4 Back Connector for DEC6800N

Figure 1-5: Back Connector for DES6800N

Table 1-3 Back Connector for DEC6800N

Location Description

1 Composite loop output(the JP1 of DEC/DES6800N has to be set on the location “off” when it is in loop through). )

DEC/DES6800 CVBS/SDI Converter - 4 -

1

2

Location Description

4 SDI output with OSD

5 SDI output with OSD

Table 1-4 Back Connector for DES6800N

Location Description

Composite loop output (the JP1 of DEC/DES6800N has to be set on the location “off” when it is in loop through). )

Audio tracking data output: not function

7

8

Signal Flow Chart

SDI output with OSD

SDI output with OSD

Figure 1-6 Signal Flow for DEC/DES6800N

Chapter 2 Installation

Overview

The power dissipation of module and the maximum power dissipation that frame can sustain have to be confirmed before module’s installation.

The following topics on installation process of DEC/DES6800N will be introduced in this chapter below:

 Unpacking Module

 Setting Jumper

 Module Installation

DEC/DES6800 CVBS/SDI Converter - 5 -

 Signal Connection

 Module Removal

Maximum Power Dissipation for Frame

The maximum voltage that 6800N series frame can sustain.

Table 2-1 Maximum voltage that 6800N Series frame that can sustain

Frame Maximum Voltage

6800N-1U 40W

6800N-2U 60W

Redundant Power Supplies

Yes

Yes

Numbers of Slots

4

10

Unpacking the Module

Preparation for Installation

Contact your dealer right away once any item is missing.

Follow the following steps before module’s installation:

 Check the equipment if any visible damage found during the transit.

 Confirm that your have received all the items listed on the packing list.

 Remove all the packing material as well as electrostatic-resistant packing if available for the equipment

 Keep these packing for future use.

Check Packing List

Table 2-2 Packed Components

Model Description

DEC6800N DEC6800 module (1pc); back connector (1pc), and other accessories

DES6800N DES6800 module (1pc); back connector (1pc), and other accessories

Module Installation

Caution ：

Static electricity may cause sensitive semiconductor out of order. Avoid installing or removing the module in the electrostatic-induced environment.

Follow the next steps to install the module:

Step 1

DEC/DES6800 CVBS/SDI Converter - 6 -

Step2

Step3

Step 4

Step5

Fig. 2-1 Installation of 2U Frame of 6800N Series

 Locate the position for back connector and insert the back connector

 Fasten the screw to fix the back connector.

 Locate the slot for module.

 Get the module installed in the slot, push the module slightly along the slot, press module again to confirm that the module is installed firmly and then close swivel handle.

 Install the front panel.

Signal Connections

All signal connections shall be made through the general bus of 6800N Series frame

Module Removal

Follow the following steps to remove VDA6800N module:

1.

Open the front panel

2.

Open the swivel handle to the full.

DEC/DES6800 CVBS/SDI Converter - 7 -

3.

First make sure that the frame stands firmly, and then pull gently the module along the slot out of frame.

4.

Install the front panel.

Chapter 3 Operation and Control

I n the chapter 3, the following topics on DES6800N are introduced:

 User’s Control

 Setting the Parameters

 Setting the Jumper

User Control and Operating Instruction

Refer the Table for BANK to fulfill the function.

Figure 3-1

SW1 SW2 Location

Select the SW1 at the location“0”, and SW2 is used to select the BANK.

BANK Selection

SW1 has four BANK.

Set SW1 to the location 0, and location “0” is always used to select BANK.

Switch SW2 up or down to select BANK A.

Table3-1 BANK Select

BANK 0

Off

Off

On

On

BANK 1

Off

On

Off

On

BANK selected

0

1

2

3

The function of SW1 is set as default, refer to Table 3-1 for defaults:

1. SW1 Mode Selection

The switch of SW1 is a 16-position rotary switch and it is used to select the specific function.

The range for selection is: 0, 1, 2, 3. 4, 5, 6, 7, 8, 9, A, B, C, D, E, F.

2. SW2 Mode Selection

The Toggle Switch of SW2

The SW2 is a toggle switch that has 3 positions with auto returning back the middle position. And it is

DEC/DES6800 CVBS/SDI Converter - 8 -

used to adjust the function that is set by SW1.

Set the SW2 at the position of UP or DOWN to allow the continuous adjustment.

All the parameters that can be configured on the DEC/DES6800N are as follows:

Table3-2

Functional Parameters of Bank 0

SW1

Position

Function

Description

OSD Text

0

1

2

3

4

5

6

7

Select bank

Turn OSD on or off

Select video standard

Analog video input gain

Chroma gain

Turn AGC on or off

Turn ACC on or off

Adjust luma gain

0:0 Bank Selection

0:1 Video: Status

(Loss/625/525)

Ref: Status

(Loss/Ref525/Ref625/Input)

0:2 Vid Standard

Auto/625/525

0:3 In Vid Gain

80.96%~200% for 625

84.93%~200% for 525

0:4 In Chm Gain

50%~200%

0:5 AGC

On/Off

0:6 ACC

On/Off

0:7 Luma Gain

50%~200%

8

9

Adjust black level

Adjust chroma gain

0:8 Black Level

7.9~-7.9IRE

0:9 Chroma Gain

50%~200%

A

B

Adjust hue

Select decoding mode

C

D

Enable or disable black clip

E

0:A Hue

90~-90 (only for NTSC)

0:B Decode Mode

Comb/Notch

0:D Black Clip

Enable/Disable

F 0:F Recall Def

Table3-3

Functional Parameters of Bank 1 (525 line rate)

Default

Bank 0

OSD

Disable

Auto

100%

100%

On

On

100%

0 IRE

100%

0

Comb

Disable

SW1

Position

0

Function

Description

Select bank

OSD

Text

1:0 Bank Selection

Default

Bank 0

DEC/DES6800 CVBS/SDI Converter - 9 -

SW1

Position

1

2

3

Function

Description

Selects the genlock

Mode

Adjust horizontal timing

Adjust vertical timing

OSD

Text

1:1 Genlcok Mode

Free Run/Ref/Input

(only for DES6800)

1:2 H Phase

0~1715

(only for DES6800)

1:3 V Phase

0~524

(only for DES6800)

1:4 Freeze

Default

Ref

0

0

4

5

Turn freeze on or off

Select type of freeze

On/Off

(only for DES6800)

1:5 Freeze Mode

Field 1/Field 2/Frame

(only for DES6800)

1:6 Hot Switch

Off

Field 1

6

7

8

Enable or disable hot switch

Select loss of video mode

Turn TSG on or off

Enable/Disable

(only for DES6800)

1:7 LossVid Mode

Disp Test/Pass/Hot Switch

1:8 TSG

On/Off

Enable

Hot

Switch

Off

9

Select color bar or black field

1:9 TSG Sel

Color Bar/Black

Black

A 1:A

B 1:B

C 1:C

D 1:D

E 1:E

F 1:F

Table3-4 Functional Parameters of Bank 1 (625 line rate)

SW1 Function

Description

Select bank

Selects the genlock

Mode

OSD Text Default

Position

0

1

2 Adjust horizontal timing

1:0 Bank Selection

1:1 Genlcok Mode

Free Run/Ref/Input

1:2 H Phase

0~1727

Bank 0

Ref

0

3 Adjust vertical timing

1:3 V Phase

0~624

0

DEC/DES6800 CVBS/SDI Converter - 10 -

SW1 Function

OSD Text Default

Position Description

4

5

6

Turn freeze on or off

Select type of freeze

Enable or disable hot switch

1:4 Freeze

On/Off

1:5 Freeze Mode

Field 1/Field 2/Frame

1:6 Hot Switch

Enable/Disable

Off

Field 1

Enable

7

8

9

Select loss of video mode

Turn TSG on or off

Select color bar or black field

1:7 LossVid Mode

Disp Test/Pass/Hot Switch

1:8 TSG

On/Off

1:9 TSG Sel

Color Bar/Black

Hot

Switch

Off

Black

A 1:A

B 1:B

C 1:C

D 1:D

E

F

Pass or blank VBI

Pass or blank VBI

1:E Line6 VBI

Blank/Pass

1:E Line7 VBI

Blank/Pass

Table3-5 Functional Parameters of Bank 2 （ 525 line rate ）

SW1 Function

Description

Select bank

OSD Text Default

Position

0 2:0 Bank Selection Bank 0

1 2:1

2 2:2

3

4

Pass or blank VBI

Pass or blank VBI

2:3 Line10 VBI

Blank/Pass

2:4 Line11 VBI

Blank/Pass

Pass

Pass

5

6

7

8

Pass or blank

Pass or blank

Pass or blank VBI

Pass or blank VBI

2:5 Line12 VBI

Blank/Pass

2:6 Line13 VBI

Blank/Pass

Line 13 VBI

2:7 Line14 VBI

Blank/Pass

2:8 Line15 VBI

Blank/Pass

Pass

Pass

Pass

Pass

DEC/DES6800 CVBS/SDI Converter - 11 -

SW1 Function

OSD Text Default

Position Description

9

A

Pass or blank VBI

Pass or blank VBI

2:9 Line16 VBI

Blank/Pass

2:A Line17 VBI

Blank/Pass

Pass

Pass

B

C

D

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

2:B Line18 VBI

Blank/Pass

2:C Line19 VBI

Blank/Pass

2:D Line20 VBI

Blank/Pass

Pass

Pass

Pass

E Pass or blank VBI

2:E Line21 VBI

Blank/Pass

Pass

F 2:F

Table3-6 Functional Parameters of Bank 2 （ 625 line rate ）

SW1

Position

0

1

2

3

4

5

6

7

8

9

A

B

Function

Description

Select bank

Bank

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

OSD

Text

2:0 Bank Selection

2:1 Line8 VBI

Blank/Pass

2:2 Line9 VBI

Blank/Pass

2:3 Line10 VBI

Blank/Pass

2:4 Line11 VBI

Blank/Pass

2:5 Line12 VBI

Blank/Pass

2:6 Line13 VBI

Blank/Pass

2:7 Line14 VBI

Blank/Pass

2:8 Line15 VBI

Blank/Pass

2:9 Line16 VBI

Blank/Pass

2:A Line17 VBI

Blank/Pass

2:B Line18 VBI

Blank/Pass

Default

Bank 0

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

DEC/DES6800 CVBS/SDI Converter - 12 -

SW1

Position

C

D

E

F

Function

Description

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

OSD

Text

2:C Line19 VBI

Blank/Pass

2:D Line20 VBI

Blank/Pass

2:E Line21 VBI

Blank/Pass

2:F Line319 VBI

Blank/Pass

Table3-7 Functional Parameters of Bank 3 (525 line rate)

Default

Pass

Pass

Pass

Pass

SW1 Function OSD

Description

Select bank

Text

3:0 Bank Selection

Default

Position

0 Bank 0

1 3:1

2 3:2

3 3:3

4

5

Pass or blank VBI

Pass or blank VBI

3:4 Line273 VBI

Blank/Pass

3:5 Line274 VBI

Blank/Pass

Pass

Pass

6

7

Pass or blank VBI

Pass or blank VBI

3:6 Line275 VBI

Blank/Pass

3:7 Line276 VBI

Blank/Pass

Pass

Pass

8

9

A

B

C

D

E

F

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

3:8 Line277 VBI

Blank/Pass

3:9 Line278 VBI

Blank/Pass

3:A Line279 VBI

Blank/Pass

3:B Line280 VBI

Blank/Pass

3:C Line281 VBI

Blank/Pass

3:D Line282 VBI

Blank/Pass

3:E Line283 VBI

Blank/Pass

3:F Line284 VBI

Blank/Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

DEC/DES6800 CVBS/SDI Converter - 13 -

Table3-7

Functional Parameters of Bank 3 (625 line rate)

SW1

Position

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

Function

Description

Select bank

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

Pass or blank VBI

OSD

Text

3:0 Bank Selection

3:1 Line320 VBI

Blank/Pass

3:2 Line321 VBI

Blank/Pass

3:3 Line322 VBI

Blank/Pass

3:4 Line323 VBI

Blank/Pass

3:5 Line324 VBI

Blank/Pass

3:6 Line325 VBI

Blank/Pass

3:7 Line326 VBI

Blank/Pass

3:8 Line327 VBI

Blank/Pass

3:9 Line328 VBI

Blank/Pass

3:A Line329 VBI

Blank/Pass

3:B Line330 VBI

Blank/Pass

3:C Line331 VBI

Blank/Pass

3:D Line332 VBI

Blank/Pass

3:E Line333 VBI

Blank/Pass

3:F Line334 VBI

Blank/Pass

Default

Bank 0

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pass

Pay attention to the followings when configuration

Composite in Video Path Processing:

The composite in video path can be processed before decoding.

The following processing functions are available for the video composite input signals:

1) Input Video Gain – adjust the input video gain in percent relative to 100% (100%=1 V p-p)

Note: only effect when AGC is OFF

2) Input Chroma Gain – adjust the percentage of chroma gain relative to 100.

Note: only effect when ACC is OFF

DEC/DES6800 CVBS/SDI Converter - 14 -

3) AGC and ACC on or off – the Auto Gain Control (AGC) and Auto Chroma Control (ACC) are set to default to the on condition. AGC operation is based on sync tip.

Decoded Video Path Processing:

The following processing functions are available for the decoded signals:

1) Luma Gain – adjusts the percentage of luminance relative to white.

2) Chroma Gain – adjusts the percentage of saturation and chroma gain relative to 100% saturation.

3) Black Level – adjusts amount of brightness/Y offset in IRE.

4) Hue – adjusts hue/chroma phase in degrees. Available in 525 mode only.

5) TSG (75% Color Bars or Black Field) – when on, enables the internal test signal generator to output a 75% Color Bars or Black Field test signal to the output.

Note: test signals are not adjustable in the Video Processing Controls.

6) On Screen Display (OSD) – enables or disables the On Screen Display on the 2 output channel.

Jumper JP5 on module must be set to OSD On control.

7) Decode Mode – select the type of decoding (filtering) from comb adaptive or notch. Adaptive decoding is 3-line in NTSC and 5-line in PAL.

8) Programmable VBI and Active Picture Lines.

9) VBI Line – blank or pass VBI lines can be selected on a line-by-line basis.

Video Timing and Freeze Controls

With a DES6800N module, the following Frame Sync timing adjustments can be made:

1) Horizontal Time – adjusts the horizontal delay on the output in pixels. This will add an additional delay of up to one line.

2) Vertical Timing – adjusts vertical delay in line increments.

3) Loss Video Mode, Auto Freeze – when Auto Freeze is enabled, the output will automatically freeze on the last valid field when the input signal is lost.

4) Hot Switch – when Hot Switch is enabled, if the input signal contains non-synchronous switches, the module will briefly provide a field freeze until it can lock to the new input timing.

5) Freeze – enable or disable manually freezes the output signal.

Freeze Mode

1) Field 1 – manually freezes the output signal on field 1.

2) Field 2 – manually freezes the output signal on field 2.

3) Frame – manually freezes the output signal on the full frame.

A field freeze provides less resolution and no motion artifacts in the output. In frame mode, the resolution is higher since both fields are present, but the presentation of the two fields can cause motion artifacts.

OSD Mode

In OSD Mode, the position of current rotary switch and parameters of navigation toggle switch can be displayed. The OSD can be turned off with either the local or remote controls before broadcasting the signal. When control is enabled with jumper JP5, it can be controlled with either local or remote controls.

Set the Jumper

Setting the following 5 jumpers is required

 JP1 set input or termination

 JP2 set reference selection

DEC/DES6800 CVBS/SDI Converter - 15 -

 JP3-set reference input

 JP4-set local or remote control

 JP5-OSD enable switch

Chapter 4 Specifications

In chapter four, the specifications about DEC/DES6800 are introduced as follows ：

 Analog video input

 SDI video processing

 SDI video output

 Phase

Analog Video Input

 Standards NTSC, PAL (Manual)

NTSC, NTSC-J, NTSC-4.43, PAL, PAL-M, SECAM (Auto)

 Level 1V

 Impedance 75

 Return Loss >40 dB to 5.8 MHz

 Video Level Adjustment +6 dB/-1 dB

SDI Video Processing

 Input 12-bit quantizing

 Decoding 5-line adaptive comb filter

 Frequency Response ±0.1 dB to 5.8MHz

 SNR >60 dB 10 kHz to 6 MHz

SDI Video Output

 Number 4

 Format

 Connector BNC

 Impedance 75

 Return Loss >18 dB to 270 MHz

 Signal Level 800mV ±10%

 DC Offset 0.0 V ±0.5 V

 Overshoot <10% of amplitude (all outputs terminated)

 Jitter <500ps

 Memory

 Data bits

Phase

 H. Adjustment Range: 1 line ， 37ns steps

 V. Adjustment Range: 1 frame ， 1 line step

Note ： Specifications are subject to change without notice.

DEC/DES6800 CVBS/SDI Converter - 16 -

Chapter 5 Warranty for

osee

product

What the warranty covers: osee warrants its products to be free from defects in material and workmanship during the warranty period of two year from purchase date. If a product proves to be defective in material or workmanship during the warranty period, osee will, at its sole option, repair or replace the product with a similar product. The replacement unit will be covered by the balance of the time remaining on the customer’s original limited warranty.

No sales personnel of the seller or any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of osee , beyond the time period describe above.

This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, osee reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer.

What the warranty does not cover:

1.

Any product on which the serial number has been defaced, modified or removed.

2.

Damage, deterioration or malfunction resulting from:

 Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product

 Repair or attempted repair by anyone not authorized by osee

 Any damage of the product due to shipment.

 Removal or installation of the product.

 Causes external to the product, such as electric power fluctuations or failure.

 Use of supplies or parts not meeting osee product’s specifications.

 Normal wear and tear.

 Any other cause which does not relate to a product defect.