Below you will find brief information for MC93XX-G Mobile Computer. The guide provides details on device setup, Android 10, features such as WLAN, Bluetooth, different keypad types, barcode scanning with imagers and laser scanners. It also covers accessories like cradles and chargers with battery safety guidelines. You'll find information on wireless configurations, NFC capabilities, application deployment, troubleshooting, and specifications for various components.
Advertisement
Advertisement
MC93XX
MN-003904-02EN Rev A
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google
LLC. All other trademarks are the property of their respective owners.
© 2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
For further information regarding legal and proprietary statements, go to:
COPYRIGHTS: www.zebra.com/copyright
WARRANTY: www.zebra.com/warranty
END USER LICENSE AGREEMENT: www.zebra.com/eula
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Changes to the original guide are listed below:
Change Date
-01 Rev A 10/2020 Initial release.
-02 Rev A 10/2021 Updated GMS Restricted topic.
Description
2
3
Entering Numbers, Symbols, and Special Characters ..................................... 43
4
Responding with a Private Response .............................................................. 62
5
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner ..................... 74
Pairing the RS507/RS507X/RS6000 Hands-Free Imager ............................................. 75
Pairing in HID Mode Using Near Field Communication.......................................... 76
Pairing Using Bluetooth Human Interface Device .................................................. 78
Pairing Using Bluetooth Human Interface Device .................................................. 79
6
7
Configuring Ethernet Static IP Address.......................................................... 113
Connecting the USB Charge/Com Snap-on Cup Cable to Host Computer.......... 122
Disconnecting the USB Charge/Com Snap-on Cup ............................................. 124
8
Installing Applications Using the USB Connection ............................................... 143
Installing Applications Using the Android Debug Bridge ...................................... 144
Downloading the System Update Package .......................................................... 145
Performing a System Update Using microSD Card.............................................. 146
Performing an Enterprise Reset From Device Settings........................................ 147
Performing an Enterprise Reset Using microSD Card ......................................... 147
Performing a Factory Reset Using microSD Card................................................ 149
Formatting a microSD Card or USB Drive as Portable Storage..................... 151
Formatting a microSD Card as Internal Memory............................................ 151
9
1-Slot USB Charging Cradle Troubleshooting...................................................... 193
16-Slot Spare Battery Charger Troubleshooting .................................................. 196
1-Slot USB Charge Cradle with Spare Battery Charger
4-Slot Charge Only ShareCradle Technical Specifications .................................. 203
10
4-Slot Ethernet ShareCradle Technical Specifications......................................... 204
4-Slot Spare Battery Charger Technical Specifications........................................ 204
16-Slot Spare Battery Charger Technical Specifications...................................... 205
USB Charge/Com Snap-on Cup Technical Specifications ................................... 206
11
This guide provides information about setting up and using the MC93XX mobile computer. Some screens shown in this guide may differ from the actual screens shown on the device.
MC93XX used in this guide refers to all configurations, except where noted. MC93XX refers to the Trigger configuration.
This guide covers the following configurations:
Table 1 Configurations
Configuration
MC93XX–G Base
Package 1
MC93XX–G Base +
NFC (Tap to Pair) +
Vibrator Motor
Radios
WLAN: IEEE 802.11 a/b/g/n/ac/d/h/i/r/w
WPAN: Bluetooth v5.0
Low Energy
WLAN: IEEE 802.11 a/b/g/n/ac/d/h/i/r/w
WPAN: Bluetooth v5.0
Low Energy
Package 2
Package 1 +
Front and Rear
Facing Cameras
MC93XX-G Freezer +
NFC (Tap to Pair) +
Vibrator Motor
WLAN: IEEE 802.11 a/b/g/n/ac/d/h/i/r/w
WPAN: Bluetooth v5.0
Low Energy
WLAN: IEEE 802.11 a/b/g/n/ac/d/h/i/r/w
WPAN: Bluetooth v5.0
Low Energy
Display
4.3" WVGA (800 x 480) LCD
4.3" WVGA (800 x 480) LCD
4.3" WVGA (800 x 480) LCD
4.3" WVGA (800 x 480) LCD.
Optically Bonded to the Touch
Panel.
Memory
4 GB RAM/
32 GB Flash
4 GB RAM /
32 GB Flash
4 GB RAM /
32 GB Flash
4 GB RAM /
32 GB Flash
SE965 1D,
SE4750-SR 2D,
SE4850-ER 2D
SE4750DPM
SE4750DPW
SE4770 2D
SE965 1D,
SE4750-SR 2D,
SE4850-ER 2D
SE4750DPM
SE4750DPW
SE4770 2D
SE965 1D,
SE4750-SR 2D,
SE4850-ER 2D
SE4770 2D
SE965 1D,
SE4750-SR 2D,
SE4850-ER 2D
SE4770 2D
Android-based,
Google ™
Mobile
Services
(GMS) 10
Android-based,
Google ™
Mobile
Services
(GMS) 10
Android-based,
Google ™
Mobile
Services
(GMS) 10
Android-based,
Google ™
Mobile
Services
(GMS) 10
12
Notational conventions are used to highlight important information.
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (for example, those that describe step-by-step procedures) appear as numbered lists.
The following icons are used throughout the document. The icons and their associated meanings are described below.
NOTE: The text here indicates information that is supplemental for the user to know and that is not required to complete a task.
IMPORTANT: The text here indicates information that is important for the user to know.
CAUTION: If the precaution is not heeded, the user could receive minor or moderate injury.
WARNING: If danger is not avoided, the user CAN be seriously injured or killed.
DANGER: If danger is not avoided, the user WILL be seriously injured or killed.
If you have a problem with your equipment, contact Customer Support for your region. Contact information is available at: zebra.com/support .
When contacting support, please have the following information available:
• Serial number of the unit (found on manufacturing label)
• Model number or product name (found on manufacturing label)
• Software type and version number
13
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, the user may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. Remove the microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.
1.
2.
3.
Before contacting Customer Support, determine the current software version on your device.
Swipe down from the Status bar with two fingers to open the Quick Access panel, and then touch .
Touch About phone .
Scroll to view the following information:
• Status
• Battery information
• SW components
• Legal information
• Model & hardware
• Android version
• Android security patch level
• Build Fingerprint
Before contacting Customer Support, determine the serial number of your device.
Touch About phone > Model & hardware > Serial number.
14
If the manufacturing label is worn or missing, use an NFC enabled device to read the NFC tag under the battery compartment. You can download the NFC Reader application for free from the Google Play store.
Manufacturing Label
NFC Tag (Inside the battery compartment.)
NFC Symbol
15
This section provides information to get the device up and running for the first time.
To unpack the device:
1.
2.
Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
Verify the following items are in the box:
3.
4.
• Mobile computer
• Lithium-ion battery
• Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global
Customer Support Center immediately.
Before using the device for the first time, remove the protective shipping film that covers the scan window, display, and camera window.
16
Figure 1 Device Front View
1
2
Getting Started
13
12
11
10
3
4
5
6
7
9
8
8
9
10
5
6
3
4
7
1
Number
2
Item
Ambient light sensor
Function
Controls display and keyboard backlight.
Front facing camera
Use to take photos and videos.
Display
The front camera is available only on the premium configurations.
Displays all information needed to operate the device.
Speaker side port Provides audio output for video and music playback.
Trigger
P1 - Dedicated
PTT key
Battery release latch
Initiates data capture when a scan application is enabled.
Initiates push-to-talk communications (programmable).
Releases the battery from the device.
Battery
Microphone
Keypad
To release the battery, simultaneously press the battery release latches on both the sides of the device.
Provides power for operating the device.
Use for communications in Handset mode.
Use to enter data and navigate on screen functions.
17
Getting Started
12
13
11
Number Item
Power button
Function
Press and hold to turn on the device. Press to turn on or off the screen. Press and hold to select one of these options:
Power off - Turn off the device.
Restart - Restart the device when software stops responding.
Initiates data capture when a scan application is enabled.
Center scan button
Charger/Decode status LED
Indicates battery charging status while charging, app generated notifications, and data capture status.
Figure 2 Device Rear View
14
15
15
16
17
14
Number
16
19
20
18
17
Item
Passive NFC tag
(Inside the battery compartment.)
Function
Provides secondary product label information (configuration, serial number and manufacture data code) in the event that the readable product label is worn or missing.
Releases the battery from the device.
Battery release latch
Side speaker port Provides audio output for video and music playback.
Scanner exit window
Provides data capture using the scanner/imager.
18
Getting Started
18
Number
19
20
Item
Camera flash
NFC antenna
Rear camera
Function
Provides illumination for the camera.
Camera is available only on some configurations.
Provides communication with other NFC-enabled devices.
NFC antenna is available only on the premium configurations.
Takes photos and videos.
The rear camera is available only on the premium configurations.
To start using the device for the first time:
1.
Install a microSD card (optional)
2.
3.
4.
Install the battery
Charge the device
Power on the device.
The microSD card slot provides secondary non-volatile storage. The slot is located under the keypad module. For more information, refer to the documentation provided with the card, and follow the manufacturer’s recommendations for use. It is strongly recommended that prior to use, you must format the microSD card on the device.
NOTE: The following microSD cards were tested and are validated for use with the MC93XX:
• SanDisk 16GB (SDSDQ-016G-A11M)
• SanDisk 32GB (SDSDQ-032G-A11M)
• SanDisk 64GB (SDSDQUA-064G-U46A)
• SanDisk 128GB (SDSDQUI-128G-A46)
• SanDisk 200GB (SDSDQUAN-200G-A4A)
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card.
Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
1.
2.
Power off the device.
Remove the battery.
19
Getting Started
3.
Using a Torx T8 screwdriver with a large grip, remove the two keypad latch screws from inside the battery slot.
1
1 Keypad latch screws
4.
Slide the keypad latches toward the bottom of the device.
1
2
1 Screwdriver
Keypad latches
NOTE: If the keypad latches are hard to move, use a screwdriver to gently slide them towards the bottom of the device.
5.
Turn the device over so that the keypad is visible.
20
Getting Started
6.
Using a Torx T8 screwdriver with a large grip, remove the two keypad assembly screws from the top of the keypad.
1
2
3
1
2
3
Keypad screws
Keypad microSD card holder
7.
8.
Lift the keypad from the device.
Slide the microSD card holder to the Open position.
9.
Lift the microSD card holder.
21
Getting Started
10.
Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
11.
Close the microSD card holder door and slide the door to the Lock position.
22
Getting Started
12.
Align the keypad along the bottom ridge of the device, and then lay it flat.
13.
Using a Torx T8 screwdriver with a large grip and a long shaft, secure the keypad to the device using the two screws. Torque screws to 5.8 kgf-cm or 5.0 lbf-in.
1
1 Keypad screws
14.
Turn the device over so that the keypad latches are visible.
23
Getting Started
15.
Slide both the keypad latches toward the top of the device.
1
1 Keypad latches
16.
Using a Torx T8 screwdriver, replace the two keypad latch screws inside the battery slot and torque to
5.8 kgf-cm or 5.0 lbf-in.
1
1 Keypad latch screws
17.
Insert the battery.
18.
Press and hold the Power key to power on the device.
24
Getting Started
1.
Align the battery with the battery slot.
2.
3.
Push the battery into the battery slot.
Press battery firmly into the battery well.
Ensure that both the battery release buttons on the sides of the device return to the home position. An audible click sound indicates that both the battery release buttons on the sides of the device have returned to the home position locking the battery in place.
4.
Press the Power button to turn on the device.
To charge the main battery:
1.
Ensure that the cradle is connected to power.
2.
Slide the mobile computer into the slot in the cradle. The mobile computer Charge LED Indicator, indicates the mobile computer battery charging status.
3.
Gently press down on the device to ensure proper contact.
4.
When charging is complete, remove the mobile computer from the cradle slot.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures, for example at approximately
+37°C (+98°F), the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
25
Getting Started
Charging Indicators
The Charge LED Indicator indicates the charge status. See the table below for charging indications.
Table 2 LED Charge Indicators
Status
Off
Slow Blinking Amber
Every 3 seconds
Indications
• The battery is not charging.
• The device is not inserted correctly in the cradle or connected to a power source.
• Cradle is not powered.
• Battery is charging, but the battery is fully depleted and does not yet have sufficient charge to power the device.
• After battery removal, indicates that the device is in hot swap mode with connectivity persistence.
Solid Amber
Solid Green
Fast Blinking Red
2 blinks/second
Solid Red
The SuperCap requires a minimum of 15 minutes to fully charge in order to provide adequate connectivity and memory session persistence.
• Battery is charging.
• Battery charging is complete.
Charging error. For example:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
• Battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
The device is equipped with a super-capacitor (supercap) to provide backup power to the device when the main battery is removed. The supercap will retain random access memory (RAM) data in memory for approximately five minutes after the main battery is removed during Hot Swap.
The supercap is automatically charged from the main battery and requires approximately fifteen minutes to fully charge.
2.
3.
The device captures and provides device analytics to a system administrator. The first time the device boots (or after a Factory reset), the Zebra Services agreement screen displays.
1.
Leave Device Data enabled if you want the device to send analytics data. Zebra recommends keeping this option enabled.
Touch the Device Data switch to disable the device from sending analytics data.
Touch OK to confirm selection.
26
Getting Started
1.
Push in the two primary Battery Release buttons.
The battery ejects slightly. With Hot Swap mode, when you remove the battery, the display turns off and the device enters a low power state. The device retains RAM data for approximately five minutes.
Replace the battery within five minutes to preserve memory persistence.
2.
Push in the secondary battery release buttons on the sides of the battery.
3.
Remove the battery from the battery slot.
4.
Align the battery with the battery slot.
5.
Push the battery into the battery slot.
27
Getting Started
6.
Press battery firmly into the battery well.
Ensure that both the battery release buttons on the sides of the device return to the home position. You will hear an audible click sound indicating that both the battery release buttons on the sides of the device have returned to the home position locking the battery in place.
7.
Press Power to turn on the device.
28
Turn on the device to display the Home screen. Depending on how your system administrator configured your device, your Home screen may appear differently than the graphics in this section.
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock.
The Home screen provides four additional screens to place widgets and shortcuts. Swipe the screen left or right to view the additional screens.
Figure 3 Home Screen
1 Status Bar
2
3
4
Widgets
Shortcut Icons
Folder
Displays the time, status icons (right side), and notification icons (left side).
For more information see Notification Icons on page 30 and
.
Launches stand-alone apps that run on the Home screen.
Opens apps installed on the device.
Contains apps.
29
Using the Device
By default, the Home screen rotation is disabled.
1.
Touch and hold anywhere on the Home screen until the options appear.
2.
3.
4.
5.
Touch Home settings .
Touch the Allow Home screen rotation switch.
Touch the Home button.
Rotate the device.
The Status bar displays the time, notification icons (left side), and status icons (right side).
If there are more notifications than can fit in the Status bar, a dot displays indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
Figure 4 Notification and Status Icons
1
2
1
Notification Icons. See Notification Icons on page 30 .
Status Icons. See
.
2
Notification Icons
Notification icons indicate app events and messages.
Table 3 Notification Icons
Icon
Main battery is low.
Description
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
Audio is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Animated: the device is downloading data. Static: the download is complete.
30
Using the Device
Table 3 Notification Icons (Continued)
Icon Description
Device is connected to or disconnected from a virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
Indicates the RxLogger app is running.
Indicates the Bluetooth scanner is connected to the device.
Indicates the ring scanner is connected to the device in HID mode.
Status Icons
Status icons display system information for the device.
Table 4 Status Icons
Icon
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Description
Main battery charge is low.
Main battery charge is very low.
Main battery is charging.
All sounds, except media and alarms, are muted. Vibrate mode is active.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network. Indicates the Wi-Fi version number.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
31
Using the Device
Table 4 Status Icons (Continued)
Icon Description
Indicates that the Orange key is locked.
Indicates that the Blue key is pressed.
Indicates that the Blue key is locked.
Indicates that the ALT key is pressed.
Indicates that the CTRL key is pressed.
Indicates that the Shift key is pressed.
Indicates that the Shift key is locked.
Indicates that the Large Key Indicator is selected.
To enable the large key indicator, go to Settings > Accessibility > Display > Large
Key Indicator .
Indicates that the Blue Key and SHIFT key are pressed enabling CAPSLOCK.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When
for a list of possible notification icons and their description.
• To view a list of all notifications, open the Notification panel by dragging the Status bar down from the top of the screen.
Quick Settings Bar
32
Using the Device
• To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
• To manage recent or frequently used notifications, open the Notification panel and then touch Manage notifications . Touch the toggle switch next to an app to turn off all notifications, or touch an app for more notification options.
• To clear all notifications, open the Notification panel and then touch CLEAR ALL . All event-based notifications are removed. Ongoing notifications remain in the list.
• To close the Notification panel, swipe the Notification panel up.
Use the Quick Access panel to access frequently used settings (for example, Airplane mode). To get to the
Quick Access Panel:
• If the device is locked, swipe down once.
• If the device is unlocked, swipe down once with two fingers, or twice with one finger.
• If the Notification panel is open, swipe down from the Quick Settings bar.
NOTE: Not all icons are pictured. Icons may vary.
Quick Access Panel Icons
• Display brightness - Use the slider to decrease or increase the brightness of the screen.
• Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch Bluetooth .
• Do not disturb - Control how and when to receive notifications.
• Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to Wi-Fi or Bluetooth.
• Auto-rotate - Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Flashlight - Turn flashlight on or off. Turn camera flash on or off.
The thermal protection safety feature for the camera provides the following behavior if the temperature range is 40°C or above:
33
Using the Device
• If the flashlight is kept on for a certain period of time, it is automatically turned off and cannot be turned back on for a period of time until it has cooled off.
• During the cooling off period, the camera cannot be turned on. If you attempt to use the camera, a message displays indicating to try again after a period of time.
• Screen Cast - Share phone content on Chromecast or a television with Google Cast built-in. Touch cast screen to display a list of devices, then touch a device to begin casting.
The first several setting tiles from the Quick Access panel become the Quick Settings bar.
Open the Quick Access panel and touch to edit, add, or remove settings tiles.
Observe the recommended battery optimization tips for your device.
• Set the screen to turn off after a short period of non-use.
• Reduce screen brightness.
• Turn off all wireless radios when not in use.
• Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
• Minimize use of apps that keep the device from suspending, for example, music and video apps.
NOTE: Before checking the battery charge level, remove the device from any AC power source (cradle or cable).
• Open Settings and touch About phone > Battery Information .
Or, swipe up from the bottom of the screen and touch to open the Battery Manager app. See
• Battery present status indicates if the battery is present.
• Battery level lists the battery charge (as a percentage of fully charged).
• Swipe down with two fingers from the status bar to open the quick access panel.
• Battery percentage is displayed next to the battery icon.
The Battery screen provides battery charge details and power management options to extend battery life.
1.
Go to Settings .
2.
Touch Battery .
Display battery information and power management options for a specific app.
1.
2.
3.
Go to Settings .
Touch Apps & notifications .
Touch an app.
34
Using the Device
4.
Touch Advanced > Battery .
Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the DISABLE or FORCE CLOSE buttons to turn off apps that consume too much power.
When the battery charge level drops below 15% on the standard battery and 30% on the freezer battery, the device displays a notice to connect the device to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 9% on the standard battery and 20% on the freezer battery, the device displays a notice to connect the device to power. The user must charge the battery using one of the charging accessories.
When the battery charge drops below 6% on the standard and freezer batteries, the device goes into a critical suspend mode to retain data, and the device turns off. The user must charge the battery using one of the charging accessories.
The device contains sensors that monitor movement, orientation and ambient light.
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
• Light Sensor - Detects ambient light and adjusts the screen brightness.
In order to take advantage of these sensors, applications use API commands. Refer to the Google Android
Sensor APIs for more information. For information on the Zebra Android EMDK, go to: techdocs.zebra.com
.
The device goes into Suspend mode when you press the Power button or after a period of inactivity (set in the Display settings window).
1.
To wake the device from Suspend mode, press the Power button or the configured wake-up sources.
The Lock screen displays.
2.
Swipe the screen up to unlock.
• If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
• If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
NOTE: If you enter the PIN, password, or pattern incorrectly five times, you must wait 30 seconds before trying again.
If you forget the PIN, password, or pattern contact your system administrator.
The device will wake on the detection of AC/DC power if it is either in suspend mode or powered off.
35
Using the Device
Connect the device to a host computer to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files. For information on USB communication accessories available for this device, see Accessories .
Use Transfer files to copy files between the device and the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
4.
On the device, pull down the Notification panel and touch Charging this device via USB .
By default, No data transfer is selected.
Touch File Transfer .
On the host computer, open a file explorer application.
5.
6.
7.
Locate the device as a portable device.
Open the Internal storage folder.
Copy files to and from the device or delete files as required.
Use PTP to copy photos from the device to the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
4.
5.
6.
On the device, pull down the Notification panel and touch Charging this device via USB .
Touch PTP .
On the host computer, open a file explorer application.
Open the Internal storage folder.
Copy or delete photos as required.
Carefully follow the host computer’s instructions to disconnect USB devices correctly to avoid losing information.
To disconnect the device from the host computer:
1.
On the host computer, unmount the device.
2.
Remove the device from the USB accessory.
36
There are multiple ways to access settings on a device.
• Swipe down with two fingers from the top of the Home screen to open the Quick Access panel and touch .
• Double-swipe down from the top of the Home screen to open the Quick Access panel and touch .
• Swipe up from the bottom of the Home screen to open APPS and touch Settings .
Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, control the keyboard backlight, set sleep time, and change font size.
Manually set the screen brightness using the touchscreen.
1.
Swipe down with two fingers from the Status bar to open the Quick Access panel.
2.
Slide the icon to adjust the screen brightness level.
To manually set the screen brightness using the keypad see Keypad Special Functions.
Automatically adjust the screen brightness using the built-in light sensor.
1.
2.
3.
4.
Go to Settings .
Touch Display .
If disabled, touch Adaptive brightness to automatically adjust the brightness.
By default, Adaptive brightness is enabled. Toggle the switch to disable.
Touch the Home button.
The Night Light setting tints the screen amber, making the screen easier to look at in low light.
1.
Go to Settings .
37
Settings
6.
7.
8.
4.
5.
2.
3.
Touch Display .
Touch Night Light .
Touch Schedule .
Select one of the schedule values:
• None (default)
• Turns on at custom time
• Turns on from sunset to sunrise.
By default, Night Light is disabled. Touch TURN ON NOW to enable.
Adjust the tint using the Intensity slider.
Touch the Home button.
By default, screen rotation is disabled.
1.
2.
3.
Go to Settings .
Touch Display > Advanced .
Touch Auto-rotate screen .
NOTE: To change the Home screen rotation, see
Setting Home Screen Rotation on page 30
.
4.
Touch the Home button.
Set the screen sleep time.
1.
2.
3.
Go to Settings .
Touch Display > Screen timeout .
Select one of the sleep values.
4.
• 15 seconds
• 30 seconds
• 1 minute
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes (default)
• Never
Touch the Home button.
The lock screen display setting wakes the screen when notifications are received.
38
Settings
3.
4.
1.
2.
5.
Go to Settings .
Touch Display > Advanced .
Touch Lock screen display .
In the When to show section, enable or disable an option using the switch.
Touch the Home button.
Set the size of the font in system apps.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch Font size .
Select one of the font size values.
5.
• Small
• Default
• Large
• Largest.
Touch the Home button.
The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
NOTE: A glove can be made of medical latex, leather, cotton, or wool.
For optimal performance use a Zebra certified stylus.
1.
2.
3.
4.
Go to Settings .
Touch Display > Advanced .
Touch Touch panel mode .
Select:
• Glove and Finger (Screen Protector off) to use a finger or a gloved finger on the screen without a screen protector.
• Stylus and Finger (Screen Protector off) to use a finger or a stylus on the screen without a screen protector.
5.
• Finger Only to use a finger on the screen.
• Glove and Finger (Screen Protector on) to use a finger or a gloved finger on the screen with a screen protector.
• Stylus and Finger (Screen Protector on) to use a finger or a stylus on the screen with a screen protector.
• Finger and Stylus to use a finger or a stylus on the screen.
• Finger and Glove to use a finger or a gloved finger on the screen.
Touch the Home button.
39
Settings
You are only required to set the time zone or set the date and time if the wireless LAN does not support
Network Time Protocol (NTP).
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch System > Date & time .
Touch Update Interval .
Select the interval time to synchronize your device time from the network.
Touch Date .
In the calendar, set today’s date.
7.
8.
9.
Touch OK .
Touch Time .
Touch the green circle, drag to the current hour and then release.
10.
Touch the green circle, drag to the current minute and then release.
11.
Touch AM or PM .
12.
Touch OK .
13.
Touch Time zone .
14.
Select the current time zone from the list.
15.
Touch Use 24-hour format .
16.
Touch the Home button.
Use the Sound settings to configure media and alarm volumes.
1.
Go to Settings .
2.
3.
Touch Sound .
Touch an option to set sounds.
• Zebra volume controls
• Ring volume - Controls the ringtone volume.
• Media volume - Controls the music, games, and media volume.
• Alarm volume - Controls the alarm clock volume.
• Notifications volume - Controls the notification volume.
• In call volume - Controls the volume during a call.
• Scanner volume - Controls the scanner volume.
40
Settings
NOTE: In the DataWedge Settings > Configure scanner settings > Scanner params menu, if Decode Audio
Feedback is set to Optimized-beep, then the scanner volume slider has no effect, and the volume defaults to the highest volume. If you want to adjust the volume of the scanner beep, then you must select the
Decode-short option under Decode Audio Feedback.
• Volume presets
• - Mutes the ring, notifications, and scanner so that the device does not make sounds or vibrate.
• - All sounds except media and alarms are silenced and vibrate mode is active.
• - Enables all sounds at the user defined levels.
• Do Not Disturb - Mutes some or all sounds and vibrations.
• Shortcut to prevent ringing - Select how the shortcut method prevents ringing.
• Default notification sound - Select a sound to play for all system notifications.
• Default alarm sound - Select a sound to play for alarms.
• Other sounds and vibrations
• Screen locking sounds - Play a sound when locking and unlocking the screen (default – enabled).
• Charging sounds and vibration - Plays a sound and vibrates when power is applied to the device
(default - enabled).
• Touch sounds - Play a sound when making screen selections (default – enabled).
• Touch vibration - Vibrate the device when making screen selections (default – disabled).
• Wireless Emergency alerts - Touch to configure emergency broadcast settings and notifications.
By default the device wakes from suspend mode when the user presses the Power button. The device can be configured to wake when the user presses the PTT or Scan buttons on the left side of the device.
1.
2.
Go to Settings .
Touch Wake-Up Sources .
3.
• P1
• SCAN
• GRIP_TRIGGER
Touch a checkbox. A check appears in the checkbox.
4.
Touch the Home button.
Buttons on the device can be programmed to perform different functions or as shortcuts to installed apps. For a list of key names and descriptions, refer to: techdocs.zebra.com
.
NOTE: It is not recommended to remap the scan button.
1.
2.
Go to Settings .
Touch Key Programmer . A list of programmable buttons displays.
41
Settings
3.
4.
5.
Select the button to remap.
Touch the BUTTON REMAPPING tab or the SHORTCUT tab that lists the available functions and applications.
Touch a function or application shortcut to map to the button.
NOTE: If you select an application shortcut, the application icon appears next to the button on the Key
Programmer screen.
6.
Touch the Home button.
The device provides multiple keyboard options.
• Gboard - GMS devices only
• Physical Keyboard
• Enterprise Keyboard
NOTE: By default the Enterprise and Virtual Keyboards are disabled.
Enabling Keyboards
1.
2.
3.
Go to Settings .
Touch System > Languages & input > Virtual keyboard > Manage keyboards .
Touch a keyboard to enable.
Enabling Virtual Keyboards
To enable a virtual keyboard like Gboard or Enterprise keyboard:
1.
2.
3.
Go to Settings .
Touch System > Languages & input > KEYBOARDS > Physical keyboard .
In the KEYBOARD ASSISTANCE area, enable Show virtual keyboard .
Switching Between Keyboards
• To switch between keyboards, touch in a text box to display the current keyboard.
• On the Gboard keyboard, touch and hold (GMS devices only).
• On the Enterprise keyboard, touch . Only available with Mobility DNA Enterprise License.Not pre-installed on the device. Contact Zebra Support for more information.
Use the Android or Gboard keyboards to enter text in a text field.
To configure the keyboard settings, touch and hold , (comma) and then select Android keyboard settings .
42
Settings
Edit Text
Edit entered text and use menu commands to cut, copy, and paste text within or across apps. Some apps do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols, and Special Characters
1.
2.
Enter numbers and symbols.
• Touch and hold one of the top-row keys until a menu appears then select a number or special character.
• Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch the Shift key a third time to unlock Capslock.
• Touch ?123 to switch to the numbers and symbols keyboard.
• Touch the =\< key on the numbers and symbols keyboard to view additional symbols.
Enter special characters.
• Touch and hold a number or symbol key to open a menu of additional symbols. A larger version of the key displays briefly over the keyboard.
The Enterprise Keyboard contains multiple keyboard types.
• Numeric
• Alpha
• Special characters
• Data capture.
Numeric Tab
The numeric keyboard is labeled 123 . The keys displayed vary on the app being used. For example, an arrow displays in Contacts , however Done displays in Email account setup.
Alpha Tab
The alpha keyboard is labeled using the language code. For English, the alpha keyboard is labeled EN .
Additional Character Tab
The additional characters keyboard is labeled #*/ .
Touch to enter emoji icons in a text message.
Touch ABC to return to the Symbols keyboard.
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Use the Language & input settings to change the device’s language, including words added to the dictionary.
43
Settings
3.
4.
1.
2.
5.
6.
Go to Settings .
Touch System > Languages & input .
Touch Languages . A list of available languages displays.
If the desired language is not listed, touch Add a language and select a language from the list.
Touch and hold to the right of the desired language, then drag it to the top of the list.
The operating system text changes to the selected language.
5.
6.
7.
3.
4.
1.
2.
Go to Settings .
Touch System > Languages & input > Advanced > Personal dictionary .
If prompted, select the language where this word or phase is stored.
Touch + to add a new word or phrase to the dictionary.
Enter the word or phrase.
In the Shortcut text box, enter a shortcut for the word or phrase.
Touch the Home button.
To set notification settings for a specific app:
1.
2.
3.
Go to Settings .
Touch Apps & notifications > SEE ALL XX APPS . The App info screen displays.
Select an app.
4.
5.
Touch Notifications .
Options vary depending on the app selected.
Select an available option:
Show notifications - Select to turn all notifications from this app on (default) or off.
Touch a notification category to display additional options.
• Alerting - Allow notifications from this app to make sound or vibrate the device.
• Pop on screen - Allow notifications from this app to pop notifications on the screen.
• Silent - Do not allow notifications from this app to make sound or vibrate.
• Minimize - In the Notification panel, collapse notifications to one line.
• Advanced - Touch for additional options.
• Sound - Select a sound to play for notifications from this app.
• Vibrate - Allow notifications from this app to vibrate the device.
• Blink light - Allow notifications from this app the light the Notification LED blue.
44
Settings
• Show notification dot - Allow notifications from this app to add a notification dot to the app icon.
• Override Do Not Disturb - Allow these notifications to interrupt when Do Not Disturb is enabled.
Advanced
• Allow notification dot - Do not allow this app to add a notification dot to the app icon.
• Additional settings in the app - Open the app settings.
Viewing Notification Settings for All Apps
To view the notification settings for all apps:
1.
2.
3.
Touch Apps & Notifications .
Scroll down to Notifications to view how many apps have notifications turned off.
To set or view notifications settings for a specific app, see Setting App Notifications on page 44 .
Controlling Lock Screen Notifications
To control whether notifications can be seen when the device is locked:
1.
2.
Touch Apps & notifications > Notifications .
Touch Notifications on lockscreen and select one of the following:
• Show alerting and silent notifications (default)
• Show alerting notifications only
• Don’t show notifications.
Blink Light
The Notification LED lights blue when an app, such as email and VoIP, generates a programmable notification or to indicate when the device is connected to a Bluetooth device. By default, LED notifications are enabled.
To change the notification setting:
1.
2.
Touch Apps & notifications > Notifications > Advanced .
Touch Blink light to toggle the notification on or off.
45
The APPS
screen displays icons for all installed apps. See Application Deployment for information on
installing and uninstalling apps. For information on standard Android apps, go to the Google Play Apps store .
The following table describes the apps installed on the device.
Table 1 Apps
Icon Description
Battery Manager - Displays battery information, including charge level, status, health and wear level.
Bluetooth Pairing Utility – Use to pair a Zebra Bluetooth scanner with the device by scanning a barcode.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments.
Camera
- Take photos or record videos. For more information, see Camera on page 53 .
Chrome - Use to access the Internet or intranet.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information.
DataWedge - Enables data capture using the imager. For more information, see
.
46
Applications
Table 1 Apps (Continued)
Icon Description
Diagnostic Tool - Use to diagnose the device. For more information, see Diagnostic Tool on page 87 .
Drive - Upload photos, videos, documents, and other files to personal storage site.
Duo - A one-to-one video calling app (WWAN only).
DWDemo - Provides a way to demonstrate the data capture features using the imager. For more information, see
DataWedge Demonstration on page 58 .
Email - Use to send and receive email.
Files - Organize and manage files on the device.
Gmail - Use to send and receive email using a Google email account.
Google - Launches Google ™ search app.
Hangouts - Use to communicate with friends using text messages and photos.
Heater Control - Use to check the status on the heater and sensors when using the device
in cold environments. See Heater Control on page 51 .
Keep - Use to create, edit, and share notes.
License Manager - Use to manage software licenses on the device.
Maps - Use to see your location on a map (with public transit, traffic, or satellite overlays).
Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance, traffic-avoidance, and alternate routes, for drivers, cyclists, walkers, and users of public transportation.
Photos - Use to sync photos with Google account.
47
Applications
Table 1 Apps (Continued)
Icon Description
Play Movies & TV - View movies and video on your device.
Play Music - Use to listen to music.
Play Store - Download music, movies, books, and Android apps and games from the
Google Play Store.
PTT Express - Use to launch PTT Express client for VoIP communication.
RxLogger
- Use to diagnose device and app issues. For more information, see RxLogger on page 64 .
RxLogger Utility - Use to view, backup, and archive RxLogger data.
Settings - Use to configure the device.
Sound Recorder
- Use to record audio. For more information, see Sound Recorder on page 65 .
StageNow - Allows the device to stage a device for initial use by initiating the deployment of settings, firmware, and software.
Velocity - Opens the Ivanti (formerly Wavelink) terminal emulation app.
VoD - The Video on Device basic app provides a how-to video for proper device cleaning.
For Video on Device licensing information, go to learning.zebra.com
.
Voice Search - Use to perform searches by asking questions.
48
Applications
Table 1 Apps (Continued)
Icon Description
Worry Free Wifi Analyzer - A diagnostic intelligent app. Use to diagnose surrounding area and display network stats, such as coverage hole detection, or AP in vicinity. Refer to the
Worry Free Wi-Fi Analyzer Administrator Guide for Android.
YouTube - Use to view videos on the YouTube ™ web site.
Zebra Bluetooth Settings - Use to configure Bluetooth logging.
All apps installed on the device are accessed using the APPS window.
1.
On the Home screen, swipe up from the bottom of the screen.
2.
3.
Slide the APPS window up or down to view more app icons.
Touch an icon to open the app.
Use the Recent button to switch between recently used apps.
1.
Touch Recent button.
2.
A window appears on the screen with icons of recently used apps.
Slide the apps displayed up and down to view all recently used apps.
3.
4.
Swipe left or right to remove app from the list and force close the app.
Touch an icon to open an app or touch Back button to return to the current screen.
The Battery Manager provides detailed information about the battery and battery swap procedures on supported devices.
To open the Battery Manager app, swipe up from the bottom of the Home screen, and then touch .
The Battery Manager displays detailed information about battery charging, health, and status.
49
Applications
Table 2 Battery Icon Description
Battery Icon Description
Battery charge level is between 85% and 100%.
Battery charge level is between 19% and 84%.
Battery charge level is between 0% and 18%.
• Level - The current battery charge level as a percentage. Displays -% when level is unknown.
• Wear - The health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
• Health - The health of the battery. If a critical error occurs, appears. Touch to view the error description.
• Decommission - The battery is past its useful life and should be replaced. See system administrator.
• Good - The battery is good.
• Charge error - An error occurred while charging. See system administrator.
• Over Current - An over-current condition occurred. See system administrator.
• Dead - The battery has no charge. Replace the battery.
• Over Voltage - An over-voltage condition occurred. See system administrator.
• Below Temperature - The battery temperature is below the operating temperature. See system administrator.
• Failure Detected - A failure has been detected in the battery. See system administrator.
• Unknown - See system administrator.
• Charge Status
• Not charging - The device is not charging.
• Charging-AC - The device is connected to AC power and charging.
• Charging-USB - The device is connected to a host computer with a USB cable and charging.
• Discharging - The battery is discharging.
• Full - That the battery is fully charged.
• Unknown - The battery status is unknown.
• Time until Full - The amount of time until the battery is fully charged.
• Time since charging - The amount of time since the device began charging.
• Time until empty - The amount of time until the battery is empty.
• Advanced info - Touch to view additional battery information.
• Battery present status - Indicates that the battery is present.
50
Applications
• Battery level - The battery charge level as a percentage of scale.
• Battery scale - The battery scale level used to determine battery level (100).
• Battery voltage - The current battery voltage in millivolts.
• Battery temperature - The current battery temperature in degrees Centigrade.
• Battery technology - The type of battery.
• Battery current - The average current into or out of the battery over the last second in mAh.
• Battery manufacture date - The date of manufacture.
• Battery serial number - The battery serial number. The number matches the serial number printed on the battery label.
• Battery part number - The battery part number.
• Battery rated capacity - Lists the rated capacity of the backup battery in mAh.
• Battery decommission status - Indicates if the battery is past its life span.
• Battery Good - The battery is in good health.
• Decommissioned Battery - The battery is past its useful life and should be replaced.
• Base cumulative charge - Cumulative charge using Zebra charging equipment only.
• Battery present capacity - Maximum amount of charge that could be pulled from the battery under the present discharge conditions if the battery were fully charged.
• Battery health percentage - With a range from 0 to 100 , this is the ratio of “present_capacity” to
“design_capacity” at a discharge rate of “design_capacity”.
• % decommission threshold - The default % decommission threshold for a gifted battery as 80%.
• Battery present charge Amount of usable charge remaining in the battery at present under the current discharge conditions.
• Battery total cumulative charge The total accumulated charge in all chargers.
• Battery time since first use The time passed since the battery was placed in a Zebra terminal for the first time.
• Battery error status - The error status of the battery.
• Battery usage number - The health of the battery as a result of charging and discharging. A high number indicates low battery health.
• Usage decommission threshold - When the Battery usage number is greater than or equal to the
Usage decommission threshold, the battery is past its useful life and should be replaced.
• App version - The application version number.
The Heater Control application provides information about the sensors and heater applicable to the freezer device. To open the Heater Control, swipe up from the bottom of the Home screen and touch .
IMPORTANT: Heater Control app is only applicable to freezer configurations.
The scanner exit window heater ensures optimum scanner performance in freezer applications.
51
Applications
The Status tab displays the following details:
• Temperature
• Display
• MLB
• Scanner
• Vent
• Scanner Window
• Scanner Bay.
• Humidity
• Scanner
• Vent
• Heater
• Scanner Window (default - enabled). This option should always be enabled for the heater to function properly. Disable this option only if you are performing debugging activities on the heater system.
The Advanced tab displays the following details:
• In the Heater area, tap to disable Scanner Window Heater . (default - enabled).
• In the Advanced area, tap to enable Logging . Logging allows you to log data for the heating system
(heaters and sensors). The data resides in the /sdcard/HeaterLogs location in a .csv file on the device.
• Click TEST HEATER to perform a diagnostic test on the heating system.
NOTE: Heater tests must be performed in an ambient environment with temperature of less than +30° C.
Once the tests are complete the results screen displays.
52
Applications
NOTE: The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.
On SDM660 platform-based products, you can use the imager and camera simultaneously. By default, third-party camera applications are associated with the Datawedge Profile0 where scanning is enabled. In these applications the Scan button initiates the scan session. If you do not want scanning to be enabled in the application, you must associate a new Datawedge profile with the application and disable scanning.
NOTE: The native Google camera application is associated with a hidden DataWedge profile. The scanning functionality is temporarily disabled when the Google camera application is being used. If a third-party camera application is utilized the scanning functionality will not be disabled allowing the simultaneous use of the scanner and the camera. This will have a direct impact on the image quality. It is strongly recommended that you use the native Google camera application.
This section provides information for taking photos and recording videos using the integrated digital cameras.
NOTE: See
for camera setting descriptions.
1.
Swipe up from the bottom of the Home screen and touch Camera .
53
Filters
Scene Mode
Applications
Camera Switch
HDR
Settings
Gallery Camera Mode
2.
3.
4.
5.
6.
7.
Shutter Button
If necessary, touch the Camera Mode icon and touch .
To switch between the rear camera and front camera (if available), touch .
Frame the subject on the screen.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Panorama mode creates a single wide image by panning slowly across a scene.
54
Applications
1.
Swipe up from the bottom of the Home screen and touch Camera .
2.
3.
4.
5.
Touch the Camera Mode icon and touch .
Frame one side of the scene to capture.
Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message Too fast appears.
Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
1.
2.
Swipe up from the bottom of the Home screen and touch Camera .
Touch the camera mode menu and touch .
55
Color Effect
Applications
Camera Switch
Audio
Settings
Gallery Camera Mode
Shutter Button
3.
4.
5.
To switch between the rear camera and front camera (if available), touch .
Point the camera and frame the scene.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6.
Touch to start recording.
The video time remaining appears in the top left of the screen.
7.
Touch to end the recording.
The video momentarily displays as a thumbnail in the lower left corner.
In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
Rear Camera Photo Settings
• Flash - Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
•
•
Off - Disable flash.
Auto - Adjust flash automatically depending upon light meter (default).
On - Enable flash upon taking a photo.
56
Applications
• Picture size - The size (in pixels) of the photo to: 13M pixels (default), 8M pixels , 5M pixels , 3M pixels , HD 1080 , 2M pixels , HD720 , 1M pixels , WVGA , VGA, or QVGA .
• Picture quality - Set the picture quality setting to: Low , Standard (default) or High .
• Countdown timer - Select Off (default), 2 seconds , 5 seconds or 10 seconds .
• Storage – Set the location to store the photo to: Phone or SD Card .
• ISO - Set camera sensitivity to light to: Auto (default), ISO Auto (HJR) , ISO100 , ISO200 , ISO400 ,
ISO800 or ISO1600 .
• Exposure - Set the exposure settings to: +2 , +1 , 0 (default), -1 or -2 .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
•
•
• Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Chroma Flash - Sets the camera to take two pictures, one with flash and one without flash. The two images are combined to produce a final image with the sharpness and clarity and bright color tones from a picture with the flash, coupled with the natural colors of a picture without a flash. Options: Off
(default) or On .
• Redeye reduction - Helps eliminate redeye effect. Options: Disabled (default), or Enable .
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled).
• Anti Banding - Allows the camera to avoid problems caused by artificial light sources that are not constant. These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options: Auto (default), 60 Hz , 50
Hz , or Off .
Front Camera Photo Settings
• Picture size - Set the size (in pixels) of the photo to: M pixels (default), HD720 , 1M pixels , WVGA ,
VGA, or QVGA .
• Picture quality - Set the picture quality setting to: Low , Standard (default) or High .
• Countdown timer - Set to: Off (default), 2 seconds , 5 seconds or 10 seconds .
• Storage – Set location to store the photo to: Phone .
• Face Detection - Select to turn face detection Off (default) or On .
In Video mode, video settings appear on screen. Touch to display the video settings options.
Rear Camera Video Settings
• Flash - Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
57
Applications
• Off - Disable flash (default).
• Torch - Turn flash on continuously.
• Video quality - Set video quality to: HD 1080p (default), HD 720p , SD 480p, .
• Video duration - Set to: 30 seconds (MMS) , or 30 minutes (default) .
• Storage – Set the location to store the photo to: Phone (default) or SD Card .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
•
• Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Image Stabilization - Set to reduce blurry videos due to device movement. Options: On or Off
(default).
Front Camera Video Settings
• Video quality - Set video quality to: HD1080 (default), HD 720p (default), HD720 , or SD 480p , VGA ,
CIF , or QVGA .
• Video duration - Set to: 30 seconds (MMS) , or 30 minutes (default).
• Storage – Set the location to store the photo to: Phone (default) or SD Card .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
•
•
Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Image Stabilization - Set to reduce blurry videos due to device movement. Options: On or Off
(default).
Use DataWedge Demonstration to demonstrate data capture functionality. To configure DataWedge, refer to techdocs.zebra.com/datawedge/ .
NOTE: DataWedge is enabled on the Home screen. To disable this feature, go to the DataWedge settings and disable the Launcher profile.
58
Applications
Table 3 DataWedge Demonstration Icons
Icon
Illumination
Description
Imager illumination is on. Touch to turn illumination off.
Data Capture
Imager illumination is off. Touch to turn illumination on.
The data capture function is through the internal imager.
Scan Mode
Menu
A Bluetooth scanner is connected.
A Bluetooth scanner is not connected.
The data capture function is through the rear camera.
Imager is in picklist mode. Touch to change to normal scan mode.
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
To select a scanner, touch > Settings > Scanner selection .
See the Data Capture section for more information.
Press the programmable button or touch the yellow scan button to capture data. The data appears in the text field below the yellow button.
59
Applications
NOTE: Requires a PTT Express License. Not available in all countries.
PTT Express Voice Client enables Push-To-Talk (PTT) communication between disparate enterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without requiring a voice communication server.
• Group Call : Press and hold the PTT (Talk) button to start communicating with other voice client users.
• Private Response : Double-press the PTT button to respond to the originator of the last broadcast or to make a Private Response.
Figure 1 PTT Express Default User Interface
Notification Icon
Service Indication
Settings
Enable/Disable Switch
Talk Group
Table 4 PTT Express Default User Interface Descriptions
Item
Notification Icon
Service Indication
Talk Groups
Settings
Enable/Disable
Switch
Lists all 32 Talk Groups available for PTT communication.
Opens the PTT Express Settings screen.
Turns the PTT service on and off.
Description
Indicates the current state of the PTT Express client.
Indicates the status of the PTT Express client. Options: Service Enabled ,
Service Disabled or Service Unavailable .
60
Applications
The following tones provide helpful cues when using the voice client.
• Talk Tone : Double chirp. Plays when the Talk button is depressed. This is a prompt for you to start talking.
• Access Tone : Single beep. Plays when another user just finished a broadcast or response. You can now initiate a Group Broadcast or Private Response.
• Busy Tone : Continuous tone. Plays when the Talk button is depressed and another user is already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
• Network Tone :
• Three increasing pitch beeps. Plays when PTT Express acquires the WLAN connection and the service is enabled.
• Three decreasing pitch beeps. Plays when PTT Express loses the WLAN connection or the service is disabled.
Notification icons indicate the current state of the PTT Express Voice client.
Table 5 PTT Express Icon Descriptions
Status Icon Description
The PTT Express Voice client is disabled.
The PTT Express Voice client is enabled but not connected to a WLAN.
The PTT Express Voice client is enabled, connected to a WLAN, and listening on the
Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and communicating on the Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and in a private response.
The PTT Express Voice client is enabled and muted.
The PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call in progress.
1.
2.
Swipe up from the bottom of the Home screen and touch .
Slide the Enable/Disable Switch to the ON position. The button changes to ON .
61
Applications
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
NOTE: This section describes the default PTT Express client configuration. Refer to the PTT Express V1.2
User Guide for detailed information on using the client.
Figure 2 PTT Button
P1 - Dedicated PTT Key
Creating a Group Call
1.
2.
Press and hold the PTT button (or the Talk button on the headset) and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that PTT Express and the WLAN are enabled.
Start talking after hearing the talk tone.
NOTE: Holding the button for more than 60 seconds (default) drops the call, allowing others to make
Group calls. Release the button when finished talking to allow others to make calls.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private
Response is made to the originator of the Group Call.
1.
2.
3.
Wait for an access tone.
Within 10 seconds, double-press the PTT button, and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that PTT Express and the WLAN are enabled.
4.
5.
Start talking after the talk tone plays.
Release the button when finished talking.
62
Applications
1.
2.
3.
Swipe up from the bottom of the Home screen and touch .
Slide the Enable/Disable Switch to the OFF position. The button changes to OFF .
Touch the Home button.
63
Applications
RxLogger is a comprehensive diagnostic tool that provides application and system metrics, and diagnoses device and application issues. RxLogger logs the following information: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat, FTP push/pull, ANR dumps, etc. All generated logs and files are saved onto flash storage on the device (internal or external).
RxLogger is built with an extensible plug-in architecture and comes packaged with a number of plug-ins already built-in. For information on configuring RxLogger, refer to techdocs.zebra.com/rxlogger/ .
To open the configuration screen, from the RxLogger home screen touch Settings .
RxLogger configuration can be set using an XML file. The config.xml
configuration file is located in the
RxLogger\config folder. Copy the file from the device to a host computer using a USB connection. Edit the configuration file and then replace the XML file on the device. There is no need to stop and restart the
RxLogger service since the file change is automatically detected.
1.
2.
3.
To enable logging:
Swipe the screen up and select .
Touch Start .
Touch the Home button.
1.
2.
3.
To disable logging:
Swipe the screen up and select .
Touch Stop .
Touch the Home button.
3.
4.
1.
2.
Connect the device to a host computer using an USB connection.
Using a file explorer, navigate to the RxLogger folder.
Copy the file from the device to the host computer.
Disconnect the device from the host computer.
RxLogger Utility allows the user to make a zip file of the RxLogger folder in the device, which by default contains all the RxLogger logs stored in the device.
64
Applications
To save the backup data, touch > BackupNow .
RxLogger Utility is a data monitoring application for viewing logs in the device while RxLogger is running.
Logs and RxLogger Utility features are accessed using Main Chat Head.
Initiating the Main Chat Head
To initiate the Main Chat Head:
1.
Open RxLogger .
2.
3.
Touch > Toggle Chat Head . The Main Chat Head icon appears on the screen.
Touch and drag the Main Chat head icon to move it around the screen.
Removing the Main Chat Head
To remove the Main Chat Head icon:
1.
Touch and drag the icon. A circle with an X appears.
2.
Move the icon over the circle and then release.
Viewing Logs
To view logs:
1.
Touch the Main Chat Head icon. The RxLogger Utility screen appears.
2.
Touch a log to open it. The user can open many logs with each displaying a new sub Chat Head.
3.
If necessary, scroll left or right to view additional Sub Chat Head icons.
4.
Touch a Sub Chat Head to display the log contents.
Removing a Sub Chat Head Icon
To remove a sub chat Head icon, press and hold the icon until it disappears.
Backing Up In Overlay View
RxLogger Utility allows the user to make a zip file of the RxLogger folder in the device, which by default contains all the RxLogger logs stored in the device.
The Backup icon is always available in Overlay View.
1.
2.
Touch . The Backup dialog box appears.
Touch Yes to create the back up.
Use Sound Recorder to record audio messages.
Recordings are saved on the microSD card (if installed) or the internal storage, and are available in the
Play Music application (GMS devices).
65
This chapter provides information for capturing barcode data using the internal camera and optional scan modules and Bluetooth scanner.
The device offers the following data capture options:
• Imager (SE4750-SR 2D, SE4850-ER 2D, SE4770 2D, SE4750DPM, and SE4750DPW).
• Laser Scanner (SE965 1D).
• Bluetooth (RS507/RS507X Hands-free imager, RS6000 Bluetooth Ring Scanner, and DS3678 Digital
Barcode Scanner).
NOTE: DataWedge is installed and enabled on the device by default.
By default, the good decode beep is set to system volume (Notifications). The good decode beep can be set to another sound (Music and Media), and the volume can be independently controlled.
The device with an integrated 2D imager has the following features:
• Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal,
PDF417, Digimarc, and 2D matrix code types.
• Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a barcode, and executes state-of-the-art software decoding algorithms to extract the barcode data from the image.
The device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing the Scan button.
• Decode mode - The device attempts to locate and decode enabled barcodes within its field of view. The imager remains in this mode as long as you hold the scan button, or until it decodes a barcode.
NOTE: To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
66
Data Capture
• Pick List mode - Selectively decode a barcode when more than one barcode is in the device’s field of view by moving the aiming crosshair or dot over the required barcode. Use this feature for pick lists containing multiple barcodes and manufacturing or transport labels containing more than one barcode type (either 1D or 2D).
The device with a laser scanner has the following features:
• Reading of a variety of barcode symbologies, including the most popular linear, and 1D code types.
• Intuitive laser aiming for easy point-and-shoot operation.
The RS507/RS507X Hands-free Imager is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 3 RS507/RS507X Hands-Free Imager
Refer to the RS507/RS507X Hands-free Imager Product Reference Guide for more information.
67
Data Capture
The RS5100 Ring Scanner is a wearable barcode scan solution for both 1D and 2D bar code symbologies.
Figure 4 RS5100 Ring Scanner
Refer to the RS5100 Ring Scanner Product Reference Guide for more information.
The RS6000 Bluetooth Ring Scanner is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 5 RS6000 Bluetooth Ring Scanner
Refer to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
The cordless DS3678 combines superior 1D and 2D omnidirectional barcode scanning performance and advanced ergonomics in a lightweight design. See the DS36X8 Product Reference Guide for more information.
68
Figure 6 DS3678 Digital Scanner
Data Capture
Typically, scanning is a simple matter of aim, scan, and decode, with a few quick trial efforts to master it.
However, consider the following to optimize scanning performance:
• Range: Scanners decode best over a particular working range — minimum and maximum distances from the barcode. This range varies according to barcode density and scanning device optics. Scan within range for quick and constant decodes; scanning too close or too far away prevents decodes.
Move the scanner closer and further away to find the right working range for the barcodes being scanned.
• Angle: Scanning angle is important for quick decodes. When the illumination/flash reflects directly back into the imager, the specular reflection can blind/saturate the imager. To avoid this, scan the barcode so that the beam does not bounce directly back. Do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
• Hold the device farther away for larger symbols.
• Move the device closer for symbols with bars that are close together.
NOTE: Scanning procedures depend on the app and device configuration. An app may use different scanning procedures from the one listed above.
To capture barcode data:
1.
Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2.
Point the top of the device at a barcode.
69
Data Capture
Figure 7 Barcode Scanning – MC93XX
3.
4.
Press and hold the Scan button or Trigger.
The red laser aiming pattern turns on to assist in aiming.
Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The Scan LEDs light green and a beep sounds, by default, to indicate the barcode was decoded successfully. Note that when the device is in Pick List Mode, the device does not decode the barcode until the center of the crosshair touches the barcode.
Figure 8 Aiming Pattern: Standard and Extended Range
Figure 9 Pick List Mode with Multiple Barcodes in Aiming Pattern: Standard and Extended Range
5.
6.
Release the scan button or Trigger.
The barcode content data appears in the text field.
To capture barcode data:
1.
Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2.
Point the top of the device at a barcode.
70
Data Capture
3.
Point the scan exit window at a barcode.
Figure 10 Barcode Scanning – MC93XX
4.
Press and hold the Scan button.
The red scan line turns on to assist in aiming. Ensure that the scan line crosses every bar and space of the barcode.
The Scan LEDs light green and a beep sounds, by default, to indicate the barcode was decoded successfully.
Figure 11 Linear Scanner Aiming Pattern
5.
6.
Release the scan button.
The captured data appears in the text field.
2.
3.
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS507/RS507X:
1.
Pair the RS507/RS507X with the device. See Pairing Bluetooth Scanners or Pairing Using Bluetooth
Human Interface Device for more information.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the RS507/RS507X at a barcode.
71
Data Capture
Figure 12 Barcode Scanning with RS507/RS507X
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS507/RS507X LEDs light green and a beep sounds to indicate the barcode was decoded successfully. When the RS507/RS507X is in Pick List mode, the RS507/RS507X does not decode the barcode until the center of the crosshair touches the barcode.
Figure 13 RS507/RS507X Aiming Pattern
Figure 14 RS507/RS507X Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
72
Data Capture
To read a barcode, a scan-enabled app is required. Devices that contain the Zebra DataWedge app allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS6000:
1.
2.
3.
Pair the RS6000 with the device. See Pairing Using Bluetooth Human Interface Device for more information.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the RS6000 at a barcode.
Figure 15 Barcode Scanning with RS6000
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS6000 LEDs light green and a beep sounds to indicate the barcode was decoded successfully.
When the RS6000 is in Pick List mode, the RS6000 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 16 RS6000 Aiming Pattern
73
Data Capture
Figure 17 RS6000 Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
To scan with the DS3608 or DS3678:
1.
Pair the scanner with the device. For more information, see Connecting a USB Scanner for the DS3608 or Pairing Bluetooth Scanners for the DS3678.
2.
3.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the scanner at a barcode.
Figure 18 Barcode Scanning (DS3678 shown)
4.
Press and hold the trigger.
Ensure the barcode is within the area formed by the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 19 DS3608/DS3678 Aiming Pattern
74
Data Capture
Figure 20 DS3608/DS3678 Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
To connect the RS507/RS507X or RS6000 imager to the device, use one of the following methods:
• Near Field Communication (NFC) (RS6000 only)
• Simple Serial Interface (SSI)
• Bluetooth Human Interface Device (HID) Mode.
NOTE: NFC is supported on the premium configurations of the device.
The MC93XX provides the ability to pair the RS6000 using NFC.
1.
2.
Ensure that NFC is enabled on the MC93XX.
Align the NFC icon on the RS6000 with the NFC icon on the back of the MC93XX.
The Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the
MC93XX. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the MC93XX screen.
The icon appears in the Status bar.
75
Figure 21 Align NFC Antennas
Data Capture
The MC93XX pairs with the RS6000 and appears in the Status bar.
NOTE: Not all Zebra devices support NFC readers and the Tap-to-Pair feature.
The MC93XX provides the ability to pair the RS6000 in HID Mode using NFC.
NOTE: NFC is supported on the premium and premium + configurations of the device and only with the
RS6000.
1.
2.
Ensure that NFC is enabled on the MC93XX.
Ensure that Bluetooth is enabled on both devices.
3.
4.
5.
Ensure that the Bluetooth device to discover is in discoverable mode.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Place the RS6000 in Human Interface Device (HID) mode. If the RS6000 is already in HID mode, skip to step 6.
a.
Remove the battery from the RS6000.
b.
Press and hold the Restore key.
c.
Install the battery onto the RS6000.
d.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
e.
Scan the barcode below to place the RS6000 in HID mode.
76
Figure 22 Bluetooth HID Barcode
Data Capture
6.
7.
8.
Remove the battery from the RS6000.
Re-install the battery into the RS6000.
Align the NFC icon on the RS6000 with the NFC icon on the MC93XX.
The Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the
MC93XX. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the MC93XX screen.
The icon appears in the Status bar.
Figure 23 Align NFC Antennas
The MC93XX pairs with the RS6000 and appears in the Status bar.
NOTE: Not all Zebra devices support NFC readers and the Tap-to-Pair feature.
To pair the RS507/RS507X or RS6000 with the device using SSI.
1.
Swipe up from the bottom of the Home screen and touch .
77
Figure 24 Bluetooth Pairing Utility
Data Capture
2.
Using the RS507/RS507X or RS6000, scan the barcode on the screen.
The RS507/RS507X or RS6000 emits a string of high/low/high/low beeps. The Scan LED flashes green indicating that the RS507/RS507X or RS6000 is attempting to establish connection with the device.
When connection is established, the Scan LED turns off and the RS507/RS507X or RS6000 emits one string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
To pair the RS507/RS507X or RS6000 with the device using Human Interface Device (HID):
1.
Ensure that Bluetooth is enabled on both devices.
2.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4.
Place the RS507/RS507X or RS6000 in HID mode. If the RS507/RS507X or RS6000 is already in HID mode, skip to step 5.
a.
b.
Remove the battery from the RS507/RS507X or RS6000.
Press and hold the Restore key.
c.
d.
e.
Install the battery onto the RS507/RS507X or RS6000.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
Scan the barcode below to place the RS507/RS507X or RS6000 in HID mode.
78
Data Capture
Figure 25 RS507 Bluetooth HID Barcode
Figure 26 RS6000 Bluetooth HID Barcode
5.
6.
Remove the battery from the RS507/RS507X or RS6000.
Re-install the battery into the RS507/RS507X or RS6000.
7.
Swipe down from the Status bar to open the Quick Access panel and then touch .
8.
9.
Touch Bluetooth .
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
10.
Scroll through the list and select RS507/RS507X or RS6000.
The device connects to the RS507/RS507X or RS6000 and Connected appears below the device name. The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
A notification appears on Notification panel and the icon appears in the Status bar.
Connect the scanner to the device using one of the following methods:
• Simple Serial Interface (SSI) mode
• Bluetooth Human Interface Device (HID) mode.
To pair the scanner with the device using HID:
1.
Remove the battery from the scanner.
2.
3.
Replace the battery.
After the scanner reboots, scan the barcode below to place the scanner in HID mode.
Figure 27 Bluetooth HID Classic Barcode
4.
5.
On the device, swipe down from the Status bar to open the Quick Access panel and then touch .
Touch Bluetooth .
79
Data Capture
6.
7.
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
Scroll through the list and select XXXXX xxxxxx, where XXXXX is the scanner and xxxxxx is the serial number.
The device connects to the scanner, the scanner beeps once and Connected appears below the device name. The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
DataWedge is a utility that adds advanced barcode scanning capability to any application without writing code. It runs in the background and handles the interface to built-in barcode scanners. The captured barcode data is converted to keystrokes and sent to the target application as if it was typed on the keypad.DataWedge allows any app on the device to get data from input sources such as a barcode scanner, MSR, RFID, voice, or serial port and manipulate the data based on options or rules.
Configure DataWedge to:
• Provide data capture services from any app.
• Use a particular scanner, reader or other peripheral device.
• Properly format and transmit data to a specific app.
To configure DataWedge refer to techdocs.zebra.com/datawedge/ .
1.
2.
3.
4.
Swipe up from the bottom of the Home screen and touch .
Touch > Settings .
Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
Touch the Home button.
1.
Touch .
2.
3.
Touch Settings .
Touch DataWedge enabled .
The blue check disappears from the checkbox indicating that DataWedge is disabled.
NOTE: DataWedge supports the decoders listed below but not all are validated on this device.
80
Data Capture
Table 6 Supported Decoders
Decoders
Australian Postal O
Aztec
Canadian Postal
Chinese 2 of 5
Codabar
Code 11
Code 128
Code 39
Code 93
Composite AB
Composite C
Discrete 2 of 5
Datamatrix
Dutch Postal
DotCode
EAN13
EAN8
Grid Matrix
GS1 DataBar
GS1 DataBar
Expanded
X
GS1 DataBar Limited O
O
X
X
X
GS1 Datamatrix
GS1 QRCode
HAN XIN
Interleaved 2 of 5
O
O
O
O
O
O
O
O
X
O
X
X
X
X
O
X
O
O
--
--
O
O
--
--
--
O
O
X
X
X
X
X
X
X
O
--
--
O
O
--
--
--
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
X
O
X
X
X
X
X
X
X
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
--
O
O
O
O
--
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
--
O
O
--
--
--
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
O
O
O
O
O
O
O
--
--
O
O
--
--
--
O
O
X
X
X
X
X
X
X
O
--
--
O
O
--
--
O
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
--
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
O
X
--
O
O
O
O
--
O
81
Table 6 Supported Decoders (Continued)
Data Capture
Decoders
Japanese Postal
Korean 3 of 5
MAIL MARK
Matrix 2 of 5
Maxicode
MicroPDF
MicroQR
MSI
PDF417
QR Code
Decoder Signature
TLC 39
Trioptic 39
UK Postal
UPCA
UPCE0
UPCE1
US4state
US4state FICS
US Planet
US Postnet
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
--
O
--
--
O
--
X
--
O
--
--
--
O
--
O
--
--
X
O
--
--
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
Key
X = Enabled
O = Disabled
-- = Not Supported
Touch the Back button to return to the previous screen.
O
O
X
X
O
O
X
O
O
X
O
--
O
O
O
O
O
X
O
O
O
--
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
O
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
--
O
X
X
O
O
X
O
O
X
O
X
O
O
O
O
O
X
O
O
O
--
O
--
--
O
--
X
--
O
--
--
--
O
--
O
--
--
X
O
--
--
82
This section provides information on the following wireless features:
• Wireless Local Area Network (WLAN)
• Bluetooth
Wireless local area networks (WLANs) allow the device to communicate wirelessly inside a building.
Before using the device on a WLAN, the facility must be set up with the required hardware to run the
WLAN (sometimes known as infrastructure). The infrastructure and the device must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches,
Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settings configure the device to match the security scheme.
The device supports the following WLAN security options:
• None
• Enhanced Open
• Wireless Equivalent Privacy (WEP)
• Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK)
• WPA3-Personal
• WPA/WPA2/WPA3 Enterprise (EAP)
• Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication.
• Transport Layer Security (TLS)
• Tunneled Transport Layer Security (TTLS) - with Password Authentication Protocol (PAP),
MSCHAP and MSCHAPv2 authentication
• Password (PWD)
• Lightweight Extensible Authentication Protocol (LEAP).
• WPA3-Enterprise 192-bit
The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status.
NOTE: To extend the life of the battery, turn off Wi-Fi when not in use.
83
Wireless
To connect to a Wi-Fi network:
1.
2.
3.
Go to Settings .
Touch Wi-Fi to open the Wi-Fi screen. The device searches for WLANs in the area and lists them.
Scroll through the list and select the desired WLAN network.
4.
5.
For open networks, touch profile once or press and hold and then select Connect or for secure networks enter the required password or other credentials then touch Connect . See the system administrator for more information.
The device obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the device with a fixed internet
protocol (IP) address, see Configuring the Device to Use a Static IP Address on page 87
.
In the Wi-Fi setting field, Connected appears indicating that the device is connected to the WLAN.
To remove a remembered or connected network:
1.
2.
3.
4.
5.
6.
Go to Settings .
Touch Network & Internet > W-Fi .
Scroll down to the bottom of the list and touch Saved networks .
Touch the name of the network.
Touch FORGET .
Touch the Home button.
This section provides information on configuring Wi-Fi settings.
3.
4.
1.
2.
5.
6.
7.
8.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the switch to the ON position.
The device searches for WLANs in the area and lists them on the screen.
Scroll through the list and select the desired WLAN network.
Touch the desired network. If the network security is Open , the device automatically connects to the network. For all other network security a dialog box appears.
If the network security is WPA/WPA2-Personal, WPA3-Personal, or WEP, enter the required password and then touch Connect .
If the network security is WPA/WPA2/WPA3 Enterprise:
• Touch the EAP method drop-down list and select one of the following:
• PEAP
84
Wireless
9.
• TLS
• TTLS
• PWD
• LEAP .
• Touch the Phase 2 authentication drop-down list and select an authentication method.
• If required, touch CA certificate and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the Security settings.
• If required, touch User certificate and select a user certificate. Note: User certificates are installed using the Security settings.
• If required, in the Identity text box, enter the username credentials.
• If desired, in the Anonymous identity text box, enter an anonymous identity username.
• If required, in the Password text box, enter the password for then given identity.
If the network security is WPA3-Enterprise 192-bit :
• Touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
• Touch User certificate and select a user certificate. Note: User certificates are installed using the
Security settings.
• In the Identity text box, enter the username credentials.
NOTE: By default, the network Proxy is set to None and the IP settings is set to DHCP . See Configuring for a Proxy Server for setting connection to a proxy server and see Configuring the Device to Use a Static
IP Address for setting the device to use a static IP address.
10.
Touch Connect .
11.
Touch the Home button.
Manually add a Wi-Fi network if the network does not broadcast its name (SSID) or to add a Wi-Fi network when out of range.
1.
2.
Go to Settings .
Touch Network & Internet > Wi-Fi .
3.
4.
5.
6.
Slide the Wi-Fi switch to the On position.
Scroll to the bottom of the list and select Add network .
In the Network name text box, enter the name of the Wi-Fi network.
In the Security drop-down list, set the type of security to:
• None
• Enhanced Open
• WEP
• WPA/WPA2-Personal
• WPA3-Personal
• WPA/WPA2/WPA3-Enterprise
85
Wireless
7.
8.
9.
• WPA3-Enterprise 192-bit
If the network security is None , touch Save .
If the network security is WEP, WPA3-Personal , or WPA/WPA2-Personal , enter the required password and then touch Save .
If the network security is WPA/WPA2/WPA3-Enterprise :
• Touch the EAP method drop-down list and select one of the following:
• PEAP
• TLS
• TTLS
• PWD
• LEAP.
• Touch the Phase 2 authentication drop-down list and select an authentication method.
• If required, touch CA certificate and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the Security settings.
• If required, touch User certificate and select a user certificate. Note: User certificates are installed using the Security settings.
• If required, in the Identity text box, enter the username credentials.
• If desired, in the Anonymous identity text box, enter an anonymous identity username.
• If required, in the Password text box, enter the password for the given identity.
10.
If the network security is WPA3-Enterprise 192-bit :
• Touch CA certificate and select a Certification Authority (CA) certificate. Note: Certificates are installed using the Security settings.
• Touch User certificate and select a user certificate. Note: User certificates are installed using the
Security settings.
• In the Identity text box, enter the username credentials.
NOTE: By default, the network Proxy is set to None and the IP settings is set to DHCP
. See Configuring for a Proxy Server on page 86
for setting connection to a proxy server and see Configuring the Device to
Use a Static IP Address on page 87 for setting the device to use a static IP address.
11.
Touch Save . To connect to the saved network, touch and hold on the saved network and select
Connect to network .
12.
Touch the Home button.
A proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers. A client connects to the proxy server and requests some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server evaluates the request according to its filtering rules. For example, it may filter traffic by IP address or protocol. If the request is validated by the filter, the proxy provides the resource by connecting to the relevant server and requesting the service on behalf of the client.
86
Wireless
It is important for enterprise customers to be able to set up secure computing environments within their companies, making proxy configuration essential. Proxy configuration acts as a security barrier ensuring that the proxy server monitors all traffic between the Internet and the intranet. This is normally an integral part of security enforcement in corporate firewalls within intranets.
1.
2.
3.
4.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the Wi-Fi switch to the On position.
In the network dialog box, select and touch a network.
5.
6.
7.
8.
9.
Touch Advanced options .
Touch Proxy and select Manual .
In the Proxy hostname text box, enter the address of the proxy server.
In the Proxy port text box, enter the port number for the proxy server.
In the Bypass proxy for text box, enter addresses for web sites that are not required to go through the proxy server. Use a comma “,” between addresses. Do not use spaces or carriage returns between addresses.
10.
Touch Connect .
11.
Touch the Home button.
By default, the device is configured to use Dynamic Host Configuration Protocol (DHCP) to assign an
Internet protocol (IP) address when connecting to a wireless network.
1.
2.
3.
4.
Go to Settings .
Touch Network & Internet > Wi-Fi .
Slide the Wi-Fi switch to the On position.
In the network dialog box, select and touch a network.
5.
6.
Touch Advanced options .
Touch IP settings and select Static .
In the IP address text box, enter an IP address for the device.
7.
8.
9.
If required, in the Gateway text box, enter a gateway address for the device.
If required, in the Network prefix length text box, enter the prefix length.
10.
If required, in the DNS 1 text box, enter a Domain Name System (DNS) address.
11.
If required, in the DNS 2 text box, enter a DNS address.
12.
Touch Connect .
13.
Touch the Home button.
Use the Wi-Fi preferences to configure advanced Wi-Fi settings. From the Wi-Fi screen scroll down to the bottom of the screen and touch Wi-Fi preferences .
• Turn on Wi-Fi automatically - When enabled, Wi-Fi automatically turns back on when near high quality saved networks.
87
Wireless
• Open network notification - When enabled, notifies the user when an open network is available.
• Advanced - Touch to expand options.
• Additional settings - See Additional Settings.
• Install Certificates – Touch to install certificates.
• Network rating provider - Disabled (AOSP devices). To help determine what constitutes a good
Wi-Fi network, Android supports external Network rating providers that provide information about the quality of open Wi-Fi networks. Select one of the providers listed or None . If none are available or selected, the Connect to open networks feature is disabled.
• MAC address - Displays the Media Access Control (MAC) address of the device when connecting to Wi-Fi networks.
• IP address - Displays the IP address of the device when connecting to Wi-Fi networks.
NOTE: Additional Wi-Fi settings are for the device, not for a specific wireless network.
Use the Additional Settings to configure additional Wi-Fi settings. To view the additional Wi-Fi settings, scroll to the bottom of the Wi-Fi screen and touch Wi-Fi Preferences > Advanced > Additional settings.
• Regulatory
• Country Selection - Displays the acquired country code if 802.11d is enabled, else it displays the currently selected country code.
• Region code - Displays the current region code.
• Band and Channel Selection
• Wi-Fi frequency band - Set the frequency band to: Auto (default), 5 GHz only or 2.4 GHz only .
• Available channels (2.4 GHz) - Touch to display the Available channels menu. Select specific channels and touch OK .
• Available channels (5 GHz) - Touch to display the Available channels menu. Select specific channels and touch OK .
• Logging
• Advanced Logging – Touch to enable advanced logging or change the log directory.
• Wireless logs - Use to capture Wi-Fi log files.
• Fusion Logger - Touch to open the Fusion Logger application. This application maintains a history of high level WLAN events which helps to understand the status of connectivity.
• Fusion Status - Touch to display live status of WLAN state. Also provides information about the device and connected profile.
• About
• Version - Displays the current Fusion information.
Wi-Fi Direct devices can connect to each other without having to go through an access point. Wi-Fi Direct devices establish their own ad-hoc network when required, letting you see which devices are available and choose which one you want to connect to.
88
Wireless
1.
2.
Go to Settings .
Touch Wi-Fi > Wi-Fi preferences > Advanced > Wi-Fi Direct . The device begins searching for another Wi-Fi Direct device.
3.
4.
Under Peer devices , touch the other device name.
On the other device, select Accept .
Connected appears on the device. On both devices, in their respective Wi-Fi Direct screens, the other device name appears in the list.
Bluetooth devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 m (32.8 ft)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (for example, files, appointments, and tasks) with other Bluetooth enabled devices such as printers, access points, and other mobile devices.
The device supports Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work. There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
• Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows enterprise devices to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 m (32.8 ft). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether in open space or closed office space.
NOTE: It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
89
Wireless
The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need.
Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the
Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction.
Bluetooth allows for a PIN or passkey used to create other 128-bit keys used for security and encryption.
The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
• Perform pairing in a secure environment
• Keep PIN codes private and do not store the PIN codes in the device
• Implement application-level security.
The device supports the Bluetooth services listed.
Table 7 Bluetooth Profiles
Profile
Service Discovery Protocol
(SDP)
Serial Port Profile (SPP)
Object Push Profile (OPP)
Advanced Audio Distribution
Profile (A2DP)
Audio/Video Remote Control
Profile (AVRCP)
Personal Area Network (PAN)
Human Interface Device Profile
(HID)
Headset Profile (HSP)
Description
Handles the search for known and specific services as well as general services.
Allows use of RFCOMM protocol to emulate serial cable connection between two Bluetooth peer devices. For example, connecting the device to a printer.
Allows the device to push and pull objects to and from a push server.
Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
Allows the device to control A/V equipment to which a user has access. It may be used in concert with A2DP.
Allows the use of Bluetooth Network Encapsulation Protocol to provide L3 networking capabilities over a Bluetooth link. Only
PANU role is supported.
Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
90
Wireless
Table 7 Bluetooth Profiles (Continued)
Profile
Hands-Free Profile (HFP)
Phone Book Access Profile
(PBAP)
Out of Band (OOB)
Description
Allows car hands-free kits to communicate with the device in the car.
Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so you can initiate a call from the car display.
Allows exchange of information used in the pairing process. Pairing is completed using the Bluetooth radio, but requires information from the OOB mechanism. Using OOB with NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
Symbol Serial Interface (SSI) Allows for communication with Bluetooth Imager.
Generic Attribute Profile (GATT) Provides profile discovery and description services for Bluetooth
Low Energy protocol. It defines how attributes are grouped together into sets to form services.
Dial Up Networking (DUN) Provides a standard to access the Internet and other dial-up services over Bluetooth.
Generic Access Profile (GAP)
OBject EXchange (OBEX)
Use for device discovery and authentication.
Facilitates the exchange of binary objects between devices.
The Bluetooth radio is off by default.
• Suspend - When the device goes into suspend mode, the Bluetooth radio stays on.
• Airplane Mode - When the device is placed in Airplane Mode, the Bluetooth radio turns off. When
Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the
Bluetooth radio can be turned back on if desired.
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (for example, an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the
Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.
NOTE: To achieve the best battery life, turn off radios when not in use.
Enabling Bluetooth
1.
Swipe down from the Status bar to open the Notification panel.
2.
3.
Touch to turn Bluetooth on.
Touch the Home button.
91
Wireless
Disabling Bluetooth
1.
2.
3.
Swipe down from the Status bar to open the Notification panel.
Touch to turn Bluetooth off.
Touch the Home button.
The device can receive information from discovered devices without pairing. However, once paired, the device and a paired device exchange information automatically when the Bluetooth radio is on.
1.
2.
Ensure that Bluetooth is enabled on both devices.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
4.
5.
6.
7.
8.
9.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Swipe down from the Status bar to open the Quick Access panel.
Touch and hold Bluetooth .
Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
Touch Pair on both devices.
The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
By default, the device has a generic Bluetooth name that is visible to other devices when connected.
1.
2.
3.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
If Bluetooth is not on, move the switch to turn Bluetooth on.
4.
5.
6.
Touch Device name .
Enter a name and touch RENAME .
Touch the Home button.
Once paired, connect to a Bluetooth device.
1.
2.
3.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
In the list, touch the unconnected Bluetooth device.
When connected, Connected appears below the device name.
Some Bluetooth devices have multiple profiles.
92
Wireless
3.
4.
5.
1.
2.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
In the Paired Devices list, touch next to the device name.
Turn on or off a profile to allow the device to use that profile.
Touch the Home button.
Unpairing a Bluetooth device erases all pairing information.
1.
2.
Go to Settings .
Touch Connected devices > Connection preferences > Bluetooth .
3.
4.
5.
In the Paired Devices list, touch next to the device name.
Touch FORGET .
Touch the Home button.
Use Cast to mirror the device screen on a Miracast enabled wireless display.
1.
Go to Settings .
2.
Touch Connected devices > Connection preferences > Cast .
3.
Touch > Enable wireless display .
The device searches for nearby Miracast devices and lists them.
4.
5.
Touch a device to begin casting.
Touch the Home button.
NFC/HF RFID is a short-range wireless connectivity technology standard that enables secure transaction between a reader and a contactless smartcard. The technology is based on ISO/IEC 14443 type A and B
(proximity), ISO/IEC 15693 (vicinity), and FeliCa standards, using the HF 13.56 MHz unlicensed band.
The device supports the following operating modes:
• Reader mode
• Peer-to-Peer communication
• Card Emulation mode.
Using NFC, the device can:
• Read contactless cards such as contactless tickets, ID cards and ePassport.
• Read and write information to contactless cards such as SmartPosters and tickets, as well as devices with NFC interface such as vending machines.
• Read information from supported medical sensors.
93
Wireless
• Pair with supported Bluetooth devices such as printers (ex. ZQ5x, ZD5x), ring scanners (ex. RS6000), and headsets (ex. HS3100).
• Exchange data with another NFC device.
• Emulate contactless card such as ticket, or SmartPoster.
The device NFC antenna is positioned to read NFC cards from the top of the device while the device is being held.
Read contactless cards using NFC.
Figure 28 Reading Cards
3.
4.
1.
2.
Launch an NFC enabled application.
Hold device as shown.
Move the device close to the NFC card until it detects the card.
Hold the card steadily until the transaction is complete (usually indicated by the application).
You can beam content like a web page, contact cards, pictures, YouTube links or location information from your screen to another device by bringing the devices together back to back.
Make sure both devices are unlocked, support NFC, and have both NFC and Android Beam turned on.
1.
Open a screen that contains a web page, video, photo or contact.
94
Wireless
2.
3.
4.
Move the back of the device toward the back of the other device.
Align the NFC logo on the device with the NFC antenna on the other device.
Move the front of the device toward the front of the other device.
When the devices connect, a sound emits, the image on the screen reduces in size, the message
Touch to beam displays.
5.
Touch anywhere on the screen.
The transfer begins.
Improve NFC performance or increase battery life by selecting which NFC features to use on the device.
• Card Detection Mode - Select a card detection mode.
• Low - Increases battery life by lowering the NFC detection speed.
• Hybrid - Provides a balance between NFC detection speed and battery life (default).
• Standard - Provides the best NFC detection speed, but reduces battery life.
• Supported Card Technology - Select an option to detect only one NFC tag type, increasing battery life, but reducing detection speed.
• All (Default) - Detects all NFC tag types. This provides the best detection speed, but reduces battery life.
• ISO 14443 Type A/B
• FeliCa
• ISO15693
• Other NFC settings available with Zebra administrator tools (CSP) - Allows configuration of additional Enterprise NFC Settings through staging tools and Mobile Device Management (MDM) solutions with an MX version that supports the Enterprise NFC Settings Configuration Service Provider
(CSP). For more information on using the Enterprise NFC Settings CSP, refer to: techdocs.zebra.com
.
95
This section provides information for using the accessories for the device. The table below lists the accessories available for the device.
Table 8 MC93XX Accessories
Accessory
Cradles
1-Slot USB Charge Cradle with Spare
Battery Charger
4-Slot Charge Only ShareCradle
4-Slot Ethernet ShareCradle
Part Number Description
CRD-MC93-2SUCHG-01 Charges the MC93XX main battery and a spare battery, and synchronizes the MC93XX with a host computer through a USB connection.
Requires power supply
(PWR-BGA12V50W0WW), DC line cord
(CBL-DC-388A1-01) and a country specific grounded AC line cord.
CRD-MC93-4SCHG-01 Charges up to four MC93XXs. Requires power supply ( PWR-BGA12V108W0WW), DC line cord
(CBL-DC-381A1-01) and a country specific grounded AC line cord .
CRD-MC93-4SETH-01 Charges up to four MC93XXs through the main battery and synchronizes the devices with a host computer through an Ethernet connection.
Requires power supply
( PWR-BGA12V108W0WW), DC line cord
(CBL-DC-381A1-01) and a country specific grounded AC line cord .
Chargers
4-Slot Spare Battery Charger SAC-MC93-4SCHG-01
16-Slot Spare Battery Charger SAC-MC93-16SCHG-01
Charges up to four MC93XX spare batteries.
Requires power supply
(PWR-BGA12V50W0WW), DC line cord
(CBL-DC-388A1-01) and a country specific grounded AC line cord.
Charges up to 16 MC93XX spare batteries.
Requires power supply
( PWR-BGA12V108W0WW), DC line cord
(CBL-DC-381A1-01) and a country specific grounded AC line cord .
96
Accessories
Table 8 MC93XX Accessories (Continued)
Power Supply
Accessory
Power Supply
Power Supply
Power Supply
Power Supply
Power Supply
Power Supply
Power Supply
US AC Line Cord
DC Line Cord
DC Line Cord
Part Number Description
PWR-BGA12V50W0WW Provides 12 VDC, 4.16A power to the 1-Slot USB
Charge Cradle and the 4-Slot Spare Battery
Charger. Requires a DC line cord
(CBL-DC-388A1-01) and a country specific grounded AC line cord.
PWR-BGA12V108W0WW Provides 12 VDC, 9A power to the 4-Slot Charge
Cradle with 4-Slot Battery Charger, and 16-Slot
Battery Charger. Requires a DC line cord
(CBL-DC-381A1-01) and a country specific grounded AC line cord.
PWR-WUA5V12W0US Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in the United
States.
PWR-WUA5V12W0GB
PWR-WUA5V12W0EU
PWR-WUA5V12W0AU
PWR-WUA5V12W0CN
PWR-WUA5V12W0IN
23844-00-00R
CBL-DC-381A1-01
CBL-DC-388A1-01
Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in the
European Union.
Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in the United
Kingdom.
Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in Australia.
Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in China.
Provides 5 VDC, 2.5A power to the USB Charge
Cable. Includes plug adapter for use in India.
Provides power to 3–wire power supplies
PWR-BGA12V50W0WW and
PWR-BGA12V108W0WW.
Provides power from the power supply
(PWR-BGA12V108W0WW) to the 4-Slot
Charge Only Cradle, 4-Slot Ethernet Cradle, and 16-Slot Battery Charger.
Provides power from the power supply
(PWR-BGA12V150W0WW) to the 1-Slot USB
Charge Cradle and 4-Slot Battery Charger.
97
Accessories
Table 8 MC93XX Accessories (Continued)
Accessory
Cables
USB Charge/Com Snap-On Cup
Part Number
CBL-MC93-USBCHG-01
Description
Provides power and/or communication over USB to the device. Requires wall adapter/power supply
PWR-WUA5V12W0xx.
A separate USB cable and power supply is required to support fast charging. USB (Type-C) Cable is required to allow communication from the snap-on to the PC/laptop.
1-Slot Cradle USB Cable CBL-TC2X-USBC-01 Provides USB communication through the 1-Slot
USB cradle to the host computer.
Miscellaneous
Cradle Adapter
7000mAh PowerPrecision+ standard battery
ADP-MC93-CRDCUP-01 MC93XX Charge Only Adapter for backwards compatibility with MC9XX cradles. Works with
MC9XX 1-Slot USB Cradle, and 4-Slot Charge
Only Cradle.
BTRY-MC93-STN-01 Replacement standard battery.
BTRY-MC93-STN-10 Replacement standard battery (10–pack).
5000mAh PowerPrecision+ freezer battery
7000mAh PowerPrecision+ non-incendive battery
MC93XX Hand Strap
MC93 Soft Holster for Gun
MC93 Rubber Boot for Gun
Screen Protector
Stylus and Tether
Un-powered Forklift Mount
BTRY-MC93-STN-IN
BTRY-MC93-FRZ-01
BTRY-MC93-FRZ-10
BTRY-MC93-NI-01
BTRY-MC93-NI-10
SG-MC93-HDSTPG-01
SG-MC9X-SHLSTG-01
SG-MC93-RBTG-01
MISC-MC93-SCRN-01
SG-TC7X-STYLUS-03
MNT-MC93-FLCH-01
Replacement standard battery (India).
Replacement freezer battery.
Replacement freezer battery (10–pack).
Replacement non-incendive battery.
Replacement non-incendive battery (10–pack).
Replacement hand strap for the MC93XX Hand strap loop holds an optional stylus
(SG-TC7X-STYLUS-03).
Provides a soft, clip on holster and a shoulder strap for the MC93XX.
Provides additional protection for wear and tear of the MC93XX.
Provides additional protection for display (5-pack).
Conductive carbon-filled stylus for capacitive touch panel; includes coiled tether (3-pack).
Un-powered forklift mount. Allows installing the device on a roll bar or square surface of a forklift.
Includes:
Forklift holder (MNT-MC93-FLCH-01), RAM double socket arm for 1” ball (MNT-RAM-B201U), and RAM forklift clamp 2.5” max width square rail base with 1” ball (MNT-RAM-B247U25).
98
Accessories
Table 8 MC93XX Accessories (Continued)
Accessory
34-key Numeric Keypad
43-key Shifted Alpha Keypad
53-key 3270 Emulator Keypad
53-key Keypad (Alpha-Numeric)
53-key 5250 Emulator Keypad
53-key VT Emulator Keypad
58-Keys OmniiXT15f Keypad
29-Keys Shifted Alpha Keypad
34-key Numeric Keypad (10 Pack)
Part Number
KYPD-MC9334FNR-01
KYPD-MC9343FN-01
KYPD-MC93533270-01
KYPD-MC93535250-01
KYPD-MC9353ANR-01
KYPD-MC9353VT-01
KYPD-MC9358ANR-01
KYPD-MC9329NMR-01
KYPD-MC9334FNR-10
43-key Shifted Alpha Keypad
(10 Pack)
53-key 5250 Emulator Keypad
(10 Pack)
53-key VT Emulator Keypad
(10 Pack)
53-key Keypad (Alpha-Numeric)
(10 Pack)
58-Keys OmniiXT15f Keypad
29-Keys Shifted Alpha Keypad
KYPD-MC9343FN-10
KYPD-MC93535250-10
KYPD-MC9353VT-10
KYPD-MC9353ANR-10
KYPD-MC9358ANR-10
KYPD-MC9329NMR-10
Description
34-key Numeric Keypad
43-key Shifted Alpha Keypad
53-key 3270 Emulator Keypad
53-key Keypad (Alpha-Numeric)
53-key 5250 Emulator Keypad
53-key VT Emulator Keypad
58-Keys OmniiXT15f Keypad
29-Keys Shifted Alpha Keypad
34-key Numeric Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
43-key Shifted Alpha Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
53-key 5250 Emulator Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
53-key VT Emulator Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
53-key Keypad (Alpha-Numeric) (10 Pack)
The 10 pack order includes a keypad installation tool.
58-Keys OmniiXT15f Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
29-Keys Shifted Alpha Keypad (10 Pack)
The 10 pack order includes a keypad installation tool.
99
Accessories
To charge the main battery:
1.
Ensure that the cradle is connected to power.
2.
Slide the mobile computer into the slot in the cradle. The mobile computer Charge LED Indicator, indicates the mobile computer battery charging status.
3.
4.
Gently press down on the device to ensure proper contact.
When charging is complete, remove the mobile computer from the cradle slot.
To charge the spare battery:
1.
Connect the charger to a power source.
2.
3.
Insert the battery into a spare battery charging slot and gently press down on the battery to ensure proper contact. The spare battery charging LEDs on the front of the cradle indicates the spare battery charging status.
When charging is complete, remove the battery from the charging slot.
Charging Indicators
The Charge LED Indicator indicates the charge status.
Table 9 LED Charge Indicators
Status
Off
Slow Blinking Amber
Every 3 seconds
Indications
• The battery is not charging.
• The device is not inserted correctly in the cradle or connected to a power source.
• Cradle is not powered.
• Battery is charging, but the battery is fully depleted and does not yet have sufficient charge to power the device.
• After battery removal, indicates that the device is in hot swap mode with connectivity persistence.
Solid Amber
The SuperCap requires a minimum of 15 minutes to fully charge in order to provide adequate connectivity and memory session persistence.
• Battery is charging.
100
Accessories
Table 9 LED Charge Indicators (Continued)
Solid Green
Status
Fast Blinking Red
2 blinks/second
Solid Red
•
Charging error. For example:
Indications
Battery charging is complete.
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
• Battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures, for example at approximately
+37°C (+98°F), the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
101
Accessories
CAUTION: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 185 .
The 1-Slot USB Charge Cradle with spare battery:
• Provides 9 VDC power to operate the mobile computer and charge the battery.
• Provides 4.2 VDC power to charge the spare battery.
• Provides a USB port for data communication between the mobile computer and a host computer or other USB devices, for example, a printer.
• Synchronizes information between the mobile computer and a host computer. With customized or third party software, it can also synchronize the mobile computer with corporate databases.
• Compatible with the following batteries:
• 7000mAh PowerPrecision+ standard battery
• 5000mAh PowerPrecision+ freezer battery
• 7000mAh PowerPrecision+ non-incendive battery.
102
Accessories
Figure 29 1-Slot USB Charge Cradle with Spare Battery Charger
1
2
3
3
4
1
2
Spare battery
Spare battery charging well
Spare battery charging LED
Indicator LED bar
4
103
Accessories
Figure 30 1-Slot USB Charge Cradle with Spare Battery Charger Setup
3
4
2
1
3
4
1
2
USB Cable
Host computer
AC Line Cord
Power Supply
104
Accessories
CAUTION: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 185 .
1.
Connect the cradle to a power source.
Figure 31 1-Slot USB Charge Cradle with Spare Battery Charger
1
2
3
4
3
4
1
2
Spare battery
Spare battery charging well
Spare battery charging LED
Indicator LED bar
3.
4.
2.
Slide the device into the slot in the cradle. The device Charge LED Indicator, indicates the battery charging status.
Gently press down on the device to ensure proper contact.
When charging is complete, remove the devices from the cradle slot.
105
Accessories
The 1-Slot USB charge cradle charges the MC93XX’s main battery and a spare battery simultaneously.
The 4-Slot Charge Only ShareCradle:
• Provides 9 VDC power to operating the mobile computer and charge the battery.
• Simultaneously charges up to four mobile computers.
• Compatible with devices using the following batteries:
• 7000mAh PowerPrecision+ standard battery
• 5000mAh PowerPrecision+ freezer battery
• 7000mAh PowerPrecision+ non-incendive battery.
Figure 32 4-Slot Charge Only ShareCradle
1
2
1
Power LED
Charging slot
2
106
Accessories
Figure 33 4-Slot Charge Only ShareCradle Setup
1
2
3
1
2
3
AC line cord
Power supply
DC line cord
107
Accessories
1.
2.
Connect the cradle to a power source.
Slide the devices into the slot in the cradle. The devices Charge LED Indicator, indicates the battery charging status.
Figure 34 4-Slot Charge Only ShareCradle
2
1
2
1
Power LED
Charging slot
3.
4.
Gently press down on the device to ensure proper contact.
When charging is complete, remove the devices from the cradle slot.
108
Accessories
The 4-Slot Ethernet ShareCradle:
• Provides 9 VDC power to operating the mobile computer and charge the battery.
• Simultaneously charges up to four mobile computers.
• Compatible with devices using the following batteries:
• 7000mAh PowerPrecision+ standard battery
• 5000mAh PowerPrecision+ freezer battery
• 7000mAh PowerPrecision+ non-incendive battery.
Figure 35 4-Slot Ethernet ShareCradle
1
2
1
Power LED
Charging slot
2
109
Accessories
Figure 36 4-Slot Ethernet ShareCradle Setup
6
3
4
5
6
1
2
AC line cord
Power supply
DC line cord
Primary port
Ethernet cable
Router
5 4
110
2
1
3
Accessories
1.
2.
Connect the cradle to a power source.
Slide the devices into the slot in the cradle. The devices Charge LED Indicator, indicates the battery charging status.
Figure 37 4-Slot Ethernet ShareCradle
1
2
1
Power LED
Charging slot
3.
4.
Gently press down on the device to ensure proper contact.
When charging is complete, remove the devices from the cradle slot.
Daisy-chain up to ten 4-Slot Ethernet ShareCradles to connect several cradles to an Ethernet network.
Use either a straight or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will almost certainly result.
To daisy-chain 4-Slot Ethernet ShareCradles:
1.
Connect power to each 4-Slot Ethernet ShareCradle.
2.
Connect an Ethernet cable to one of the ports on the switch and the other end to the Primary Port of the first cradle.
111
2
Accessories
3.
4.
Connect an Ethernet cable to the Secondary port of the first cradle.
Connect the other end of the Ethernet cable to the Primary port of the next 4-Slot Ethernet
ShareCradle.
Figure 38 Daisy-chaining 4-Slot Ethernet ShareCradles
1 2
3
8
4
5
7
8
5
6
3
4
1
2
7
Primary port
Secondary port
First cradle
To power supply
Second cradle
To power supply
Ethernet cable to next cradle
To Ethernet switch
6
5.
Connect additional cradles as described in step 3 and 4.
Ethernet Settings
The following settings can be configured when using Ethernet communication:
• Proxy Settings
• Static IP.
112
Accessories
Configuring Ethernet Proxy Settings
5.
6.
7.
3.
4.
1.
2.
The MC93XX includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
Swipe down from the status bar to open the quick access panel and then touch .
Touch Network & Internet > Ethernet .
Slide the switch to the ON position.
Place the device into the Ethernet cradle slot.
Touch and hold eth0 until the menu appears.
Touch Modify Proxy .
Touch the Proxy drop-down list and select Manual .
8.
9.
In the Proxy hostname field, enter the proxy server address.
In the Proxy port field, enter the proxy server port number.
NOTE: When entering proxy addresses in the Bypass proxy for field, do not use spaces or carriage returns between addresses.
10.
In the Bypass proxy for text box, enter addresses for web sites that do not require to go through the proxy server. Use the separator comma “,” between addresses.
11.
Touch MODIFY .
12.
Touch the Home button.
Configuring Ethernet Static IP Address
The MC93XX includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1.
2.
Swipe down from the status bar to open the quick access panel and then touch .
Touch Network & Internet > Ethernet .
113
Accessories
5.
6.
3.
4.
7.
8.
Slide the switch to the ON position.
Place the device into the Ethernet cradle slot.
Touch eth0 .
Touch Disconnect .
Touch eth0 .
Touch the IP settings drop-down list and select Static .
9.
In the IP address field, enter the proxy server address.
10.
If required, in the Gateway field, enter a gateway address for the device.
11.
If required, in the Netmask field, enter the network mask address
12.
If required, in the DNS address fields, enter a Domain Name System (DNS) addresses.
13.
Touch CONNECT .
14.
Touch the Home button.
Establishing Ethernet Connection
1.
2.
3.
Double-swipe down from the top of the Home screen to open the Quick Access panel and touch .
Touch Network & Internet > Ethernet .
Slide the Ethernet switch to the ON position.
114
Accessories
4.
5.
Place the device into the Ethernet cradle slot.
Touch eth0 to view Ethernet connection details.
LED Indicators
There are two green LEDs on the side of the cradle. These green LEDs light and blink to indicate the data transfer rate.
Table 10 LED Data Rate Indicators
Data Rate
1 Gbps
100 Mbps
10 Mbps
On/Blink
Off
Off
1000 LED 100/10 LED
Off
On/Blink
On/Blink
115
Accessories
CAUTION: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 185 .
The 4-Slot Spare Battery Charger:
• Charges up to 4 spare batteries.
• Provides 4.2 VDC power to charge the spare battery.
Figure 39 4-Slot Spare Battery Charger Setup
1
2
3
5
4
3
4
1
2
5
Power supply
AC line cord
DC line cord
Spare battery charging LED
Charging slot
116
Accessories
Charging the Spare Batteries
1.
Connect the charger to a power source.
Figure 40 4-Slot Spare Battery Charger
1
2
1
2
Spare battery charging LEDs
Power LED
2.
Insert the battery into a spare battery charging slot and gently press down on the battery to ensure proper contact.
117
Accessories
CAUTION: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 185 .
The 16-Slot Spare Battery Charger:
• Charges up to 16 spare batteries.
• Provides 4.2 VDC power to charge the spare battery.
Figure 41 16-Slot Spare Battery Charger Setup
1
2
4
3
3
4
1
2
AC line cord
Power supply
DC line cord
Charging slot
118
Accessories
Charging the Spare Batteries
CAUTION: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 185 .
1.
Connect the charger to a power source.
Figure 42 16-Slot Spare Battery Charger
1
2
1
2
Power LED
Spare battery charging LED
2.
Insert the battery into a spare battery charging slot and gently press down on the battery to ensure proper contact.
119
Accessories
The USB Charge/Com Snap-on Cup:
• Provides 5 VDC power to operate the device and to charge the battery.
• Provides power and/or communication with the host computer over USB to the device.
Figure 43 USB Charge/Com Snap-on Cup
2
1
2
Pigtail with USB socket
USB charge/com snap-on cup
1
120
Accessories
NOTE: To function properly, remove the lower part of the rubber boot or the entire rubber boot before placing the device in a charging cradle.
Insert the device straight onto the USB Charge/Com Snap-on Cup until the device touches the bottom of the cable cup.
Figure 44 Connecting the USB Charge/Com Snap-on Cup
121
Accessories
To connect the USB Charge/Com Snap-on Cup cable to a host computer:
1.
Connect the USB Charge/Com Snap-on Cup to the device.
2.
Connect the USB connector to a host computer.
Figure 45 Connecting USB Charge/Com Snap-on Cup to Host Computer
1
2
3
1
2
3
Host computer
USB cable
USB charge/com snap-on cup
122
Accessories
To charge the device using the USB Charge/Com Snap-on Cup:
1.
Connect the USB Charge/Com Snap-on Cup to the device.
2.
Connect the USB connector of the power supply.
3.
Plug the power supply into a power outlet.
Figure 46 Charging the Device using the USB Charge Cable
1
2
1
2
Power supply
USB cable
123
Accessories
To disconnect the USB Charge/Com Snap-on Cup from the device:
1.
Depress the two latches on either side of the cup.
2.
Pull the cup off the bottom of the device.
Figure 47 Disconnecting the USB Charge/Com Snap-on Cup
124
Accessories
Use the Charge Only Adapter for backwards compatibility with the MC9XXX cradles and the MC93XX mobile computer.
• Charge Only Adapter supports terminal charging only for the MC9XXX 1-Slot Cradle and 4-Slot Cradle.
• Charge Only Adapter provides charge only and no communication when used with the MC9XXX cradles.
Figure 48 MC9X 1-Slot Cradle Charge Only Adapter
1
1
2
Charge only adapter
MC92 1-Slot cradle
2
125
Accessories
Figure 49 MC9X 4-Slot Cradle Charge Only Adapter
1
1
2
2
Charge only adapter
MC92 4-Slot cradle
To install the Charge Only Adapter:
1.
Clean the MC9XXX cradle and contacts surface as specified with an alcohol wipe, using a back and forth motion with your finger.
For more information about cleaning, refer to the MC93XX Mobile Computer User Guide.
1 Clean cradle contacts and surface
1
126
Accessories
2.
Peel and remove the adhesive from the back of the adapter.
1
1 Peel and remove adhesive liner
3.
Insert the adapter into the MC9XXX cradle and adhere to the bottom of the cradle.
127
4.
Insert the device into the cradle.
Accessories
128
Accessories
To attach the rubber boot:
1.
If using the rubber boot with a device with the SE965 laser scanner, retain the shim (default assembly).
If using the rubber boot with a device with either the SE4750SR or the SE4850ER imager, you must snap-off the shim by pushing it through.
2.
Slide the top of the device into the top of the rubber boot.
3.
Grasp the bottom of the rubber boot and place over the bottom of the device.
4.
Turn the device over and ensure that the two alignment tabs completely fit into the two alignment slots on the device.
1
129
Accessories
1 Tabs
NOTE: To charge the device in a cradle, completely remove the rubber boot.
To install the hand strap:
1.
Thread and
the opening near the base of the trigger handle.
2.
Thread and
the opening near the battery.
3.
Attach the two plastic ends together.
130
Accessories
The Un-powered Forklift Mount on a forklift allows you to place the device in a holder. The forklift mount does not provide charging or communication to the device. Install the Forklift Mount on a square surface or roll bar of a forklift. The mount supports portrait (vertical) orientation only.
To install the MC93XX in an un-powered forklift mount holder:
1.
Secure the RAM Clamp Base to the forklift mounting surface using two screws and nuts.
2.
3.
Attach the RAM Socket Arm to the RAM Clamp Base and the Forklift Mount Holder.
Turn the Socket Arm hand-screw clockwise until tight.
5$0&ODPS%DVH
5$06RFNHW$UP
6WUDS
5$0&ODPS%DVH
)RUNOLIW0RXQWLQJ6XUIDFH
)RUNOLIW0RXQW+ROGHU
4.
5.
6.
Insert the device into the Forklift Mount Holder at a 45° angle in one of two ways (shown below).
Rotate and snap the device into place.
If required, secure the device with the rubber strap, and snap it into place.
Figure 50 Insert Device into Forklift Mount Holder, Rotate and Snap (Option 1)
131
Accessories
Figure 51 Insert Device into Forklift Mount Holder, Rotate and Snap (Option 2)
NOTE: Use strap in this orientation for added retention of the device.
Use the Rack/Wall Mount Bracket to mount a 4-slot charge only sharecradle on a rack. When installing on a rack, first assemble the bracket and cradles/chargers and then install the assembly on the rack.
1.
2.
Place the power supply in bottom tray.
Connect AC line cord to power supply.
3.
4.
Connect DC line cord to power supply.
Secure power supply and cables to bottom tray with tie wraps.
NOTE: Ensure tie wrap buckle is on side of power supply. Tie wrap buckle on top of power supply interferes with top tray.
5.
Route cables through cable slots.
1 2 3
1
2
3
DC line cord
Power supply
AC line cord
132
Accessories
6.
Secure four M2.5 studs to top tray as shown.
7.
Align and install 4-Slot cradle onto studs of top tray.
MC93
MC93
MC93
MC93
8.
Secure cradle to top tray with two M2.5 safety screws.
1
1
Safety screws (2)
133
9.
Slide top tray onto bottom tray.
Accessories
10.
Connect cables to cradle.
11.
Secure top tray to bottom tray with 4 M5 screws (two on each side).
See
Rack Mount Installation on page 135
for installing the bracket assembly onto a rack.
134
Accessories
NOTE: Use screws provided with rack system. Refer to the rack user documentation for instructions.
1.
Secure mounting brackets to both sides of top tray with four M5 screws (two on each side). For 4-Slot cradles, position the flange for horizontal installation. For 4-Slot Battery Chargers, position the flange for 25° installation.
Figure 52 Flange Horizontal Position (4-Slot Cradles)
1
2
1
2
Flange
Fifth screw hole
Figure 53 Flange 25° Position (4-Slot Battery Chargers)
1
2
1
2
Top screw hole
Flange
CAUTION: Install mounting bracket with 4-Slot cradle at a maximum height of four feet from ground.
Install mounting bracket with 4-Slot Battery Charger at a maximum height of three feet from ground.
135
Accessories
NOTE: Distance between two horizontal mounted brackets should be at least 14” apart (from top of one flange to the top of the next flange).
Distance between a horizontal mounted bracket and a 25° mounted bracket should be at least 16.25” apart
(from top of one flange to the top of the next flange).
There should be enough clearance (2.75”) between the top of the device and the bottom of the mounting bracket above.
2.
Install two rack system screws for top of mounting brackets. The screw heads should protrude half way from the rail.
Figure 54 Install Rack System Screws
1
1
2
Rack screw
Rack screw
3.
4.
Align the mounting bracket’s top mounting key holes with the screws.
Place the brackets on the screws.
2
136
Accessories
Figure 55 Secure Bracket to Rack (Horizontal Position Shown)
MC93
MC93
MC93
MC93
14 “
MC93
MC93
MC93
MC93
5.
6.
7.
Secure the top screws.
Install bottom screws and tighten screws.
Route cables and connect to power source.
CAUTION: Installer should ensure that all building codes are followed when connecting the power supplies to an AC power source.
While installing the brackets, power supplies and cables:
• Use tie wraps to secure cables to the bracket and rails.
• Coil cables wherever possible.
• Route power cables along the rails.
Route inter-cradle cables to the side rails and then from the rails to the bracket.
137
Accessories
Use the Rack/Wall Mount Bracket to mount four 4-Slot Battery Chargers or a cradle on a wall. When installing on a wall, first assemble the bottom tray, install the bottom tray on the wall and then assemble the top tray.
Use mounting hardware (screws and/or anchors) appropriate for the type of wall mounting the bracket onto. The Mount Bracket mounting slots dimensions are 5 mm (0.2 in.). Fasteners must be able to hold a minimum of 20 Kg (44 lbs.)
For proper installation consult a professional installer. Failure to install the bracket properly can possibly result in damage to the hardware.
CAUTION: Install mounting bracket with 4-Slot cradle at a maximum height of four feet from ground.
Install mounting bracket with 4-Slot Battery Charger at a maximum height of three feet from ground.
See steps 1 through 5 in
4-Slot Charge Only ShareCradle Rack Installation on page 132
for instructions.
1.
2.
Drill holes and install anchors according to the template supplied with the bracket.
Install two screws for bottom of bracket. The screw heads should protrude 2.5 mm (0.01”) from the wall.
Figure 56 Horizontal Mounting Template
398 mm
22.85 mm
3.
Align the mounting bracket’s bottom mounting key holes with the screws.
138
4.
Hang the bracket on the screws.
Accessories
5.
6.
Install two top screws.
Tighten all screws.
7.
8.
Assemble the four 4-Slot Battery Chargers or cradle onto the bracket. See steps 7 through 11 in
Charge Only ShareCradle Rack Installation on page 132 .
Route cables and connect to power source.
CAUTION: Installer should ensure that all building codes are followed when connecting the power supplies to an AC power source.
While installing the brackets, power supplies and cables:
• Use tie wraps to secure cables to the bracket and rails.
• Coil cables wherever possible.
• Route power cables along the rails.
• Route inter-cradle cables to the side rails and then from the rails to the bracket.
139
The device implements a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).
NOTE: Ensure the date is set correctly before installing certificates or when accessing secure web sites.
If the VPN or Wi-Fi networks rely on secure certificates, obtain the certificates and store them in the device’s secure credential storage, before configuring access to the VPN or Wi-Fi networks.
If downloading the certificates from a web site, set a password for the credential storage. The device supports X.509 certificates saved in PKCS#12 key store files with a .p12 extension (if key store has a .pfx or other extension, change to .p12).
The device also installs any accompanying private key or certificate authority certificates contained in the key store.
To install a secure certificate:
1.
Copy the certificate from the host computer to the root of the device’s internal memory. See
Communication on page 36 for information about connecting the device to a host computer and
copying files.
2.
3.
4.
5.
6.
7.
8.
Go to Settings .
Touch Security > Advanced > Encryption & credentials .
Touch Install from storage .
Navigate to the location of the certificate file.
Touch the filename of the certificate to install.
If prompted, enter the password for credential storage. If a password has not been set for the credential storage, enter a password for it twice and then touch OK .
If prompted, enter the certificate’s password and touch OK .
140
Application Deployment
9.
Enter a name for the certificate and in the Credential use drop-down, select VPN and apps or Wi-Fi .
10.
Touch OK .
The certificate can now be used when connecting to a secure network. For security, the certificate is deleted from the internal memory.
1.
2.
Go to Settings .
Touch Security > Advanced > Encryption & credentials .
• Trusted credentials - Touch to display the trusted system and user credentials.
• User credentials - Touch to display user credentials.
• Install from storage - Touch to install a secure certificate from the internal storage.
• Clear credentials - Deletes all secure certificates and related credentials.
Development tools for Android include Android Studio, EMDK for Android, and StageNow.
Development Workstation
Android development tools are available at developer.android.com
.
To start developing applications for the device, download Android Studio. Development can take place on a Microsoft® Windows®, Mac® OS X®, or Linux® operating system.
Applications are written in Java or Kotlin, but compiled and executed in the Dalvik virtual machine. Once the Java code is compiled cleanly, the developer tools make sure the application is packaged properly, including the AndroidManifest.xml file.
Android Studio contains a full featured IDE as well as SDK components required to develop Android applications.
Enabling Developer Options
The Developer options screen sets development related settings. By default, the Developer Options are hidden.
1.
2.
3.
4.
5.
6.
7.
Go to Settings .
Touch About phone .
Scroll down to Build number .
Tap Build number seven times. The message You are now a developer!
appears.
Touch the Back button.
Touch System > Advanced > Developer options .
Slide the USB debugging switch to the ON position.
141
Application Deployment
EMDK for Android provides developers with tools to create business applications for enterprise mobile devices. It is designed for use with Google's Android Studio and includes Android class libraries such as
Barcode, sample applications with source code, and the associated documentation.
EMDK for Android allows applications to take full advantage of the capabilities that Zebra devices have to offer. It embeds Profile Manager technology within Android Studio IDE, providing a GUI-based development tool designed specifically for Zebra devices. This allows fewer lines of code, resulting in reduced development time, effort, and errors.
For more information go to: techdocs.zebra.com
.
StageNow is Zebra's next-generation Android Staging Solution built on the MX platform. It allows quick and easy creation of device profiles, and can deploy to devices simply by scanning a barcode, reading a tag, or playing an audio file.
The StageNow Staging Solution includes the following components:
• The StageNow Workstation tool installs on the staging workstation (host computer) and lets the administrator easily create staging profiles for configuring device components, and perform other staging actions such as checking the condition of a target device to determine suitability for software upgrades or other activities. The StageNow Workstation stores profiles and other created content for later use.
• The StageNow Client resides on the device and provides a user interface for the staging operator to initiate staging. The operator uses one or more of the desired staging methods (print and scan a barcode, read an NFC tag or play an audio file) to deliver staging material to the device.
For more information go to: techdocs.zebra.com
.
GMS Restricted mode deactivates Google Mobile Services (GMS). All GMS apps are disabled on the device and communication with Google (analytics data collection and location services) is disabled.
Use StageNow to disable or enable GMS Restricted mode. After a device is in GMS Restricted mode, enable and disable individual GMS apps and services using StageNow. To ensure GMS Restricted mode persists after an Enterprise Reset, use the Persist Manager option in StageNow. For more information on
StageNow, refer to techdocs.zebra.com
.
To use the ADB, install the USB driver. This assumes that the development SDK has been installed on the host computer. Go to developer.android.com/sdk/index.html
for details on setting up the development
SDK.
ADB driver for Windows and Linux are available on the Zebra Support Central web site at www.zebra.com/support . Download the ADB and USB Driver Setup package. Follow the instructions with the package to install the ADB and USB drivers for Windows and Linux.
By default, USB debugging is disabled.
142
Application Deployment
7.
8.
5.
6.
9.
3.
4.
1.
2.
Go to Settings .
Touch About phone .
Scroll down to Build number .
Tap Build number seven times. The message You are now a developer!
appears.
Touch the Back button.
Touch System > Advanced > Developer options .
Slide the USB debugging switch to the ON position.
Touch OK .
Connect the device to the host computer using the Rugged Charge/USB Cable.
The Allow USB debugging?
dialog box appears on the device.
10.
On the device, touch OK .
11.
On the host computer, navigate to the platform-tools folder.
12.
Type adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
13.
Touch the Home button.
After an application is developed, install the application onto the device using one of the following methods:
• USB connection, see
Installing Applications Using the USB Connection on page 143 .
• Android Debug Bridge, see
Installing Applications Using the Android Debug Bridge on page 144 .
•
microSD Card, see Installing Applications Using a microSD Card on page 144
.
• Mobile device management (MDM) platforms that have application provisioning. Refer to the MDM software documentation for details.
3.
4.
1.
2.
5.
Connect the device to a host computer using the Rugged Charge/USB cable.
Pull down the Notification panel and touch Charging this device via USB .
Touch File Transfer .
On the host computer, open a file manager application.
On the host computer, copy the application .apk file from the host computer to the device.
143
Application Deployment
CAUTION: Carefully follow the host computer’s instructions to unmount the microSD card and disconnect
USB devices correctly to avoid losing information.
6.
Disconnect the device from the host computer.
7.
Swipe the screen up and select to view files on the Internal Storage.
8.
9.
Locate the application .apk file.
Touch the application file.
10.
Touch Continue to install the app or Cancel to stop the installation.
11.
To confirm installation and accept what the application affects, touch Install otherwise touch Cancel .
12.
Touch Open to open the application or Done to exit the installation process. The application appears in the App list.
Use ADB commands to install application onto the device.
1.
Ensure that the ADB drivers are installed on the host computer. See
.
2.
Connect the device to a host computer using USB. See USB Communication on page 36 .
3.
4.
5.
6.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
7.
8.
Touch OK .
On the host computer, open a command prompt window and use the adb command: adb install <application>
9.
where: <application> = the path and filename of the apk file.
Disconnect the device from the host computer. See
.
When connecting the device to a host computer and mounting its microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
It is strongly recommended that prior to use, you must format the microSD card on the device.
1.
Copy the apk file to the root of the microSD card.
2.
3.
• Copy the apk file to a microSD card using a host computer (see USB Communication for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer, and copy apk file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
Connect the device to a host computer using USB. See USB Communication.
Copy the application APK file from the host computer to the microSD card.
144
Application Deployment
4.
Remove the microSD card from the host computer.
5.
Press and hold the Power button on the device until the menu appears.
6.
7.
Touch Power off .
Remove the battery from the device.
8.
Remove the keypad.
9.
Slide the microSD card holder to the Open position.
10.
Lift the microSD card holder.
11.
Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
12.
Close the microSD card holder door and slide the door to the Lock position.
13.
Replace the keypad.
14.
Insert the battery.
15.
Press and hold the Power button to turn on the device.
16.
Swipe the screen up and select to view files on the microSD card.
17.
Touch > SD card .
18.
Locate the application .apk file.
19.
Touch the application file.
20.
Touch Continue . to install the app or Cancel to stop the installation.
21.
To confirm installation and accept what the application affects, touch Install otherwise touch Cancel .
22.
Touch Open to open the application or Done to exit the installation process. The application appears in the App list.
5.
6.
7.
3.
4.
1.
2.
Go to Settings .
Touch Apps & notifications .
Touch See all apps to view all apps in the list.
Scroll through the list to the app.
Touch the app. The App info screen appears.
Touch Uninstall .
Touch OK to confirm.
System Update packages can contain either partial or complete updates for the operating system. Zebra distributes the System Update packages on the Zebra Support & Downloads web site. Perform a system update using either a microSD card or using ADB.
1.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
145
Application Deployment
2.
Download the appropriate System Update package to a host computer.
It is strongly recommended that prior to use, you must format the microSD card on the device.
1.
Copy the System Update zip file to the root of the microSD card.
2.
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer, and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
3.
4.
5.
6.
Touch Restart .
Press and hold the Trigger button until the device vibrates. The System Recovery screen appears.
Press the Up and Down buttons to navigate to Apply upgrade from SD card .
Press the Enter button.
7.
8.
Use the Up and Down buttons to navigate to Full OTA Package or Diff OTA Package .
Press the Enter button.
9.
Use the Up and Down buttons to navigate to the System Update file.
10.
Press the Power button. The System Update installs and then the device returns to the Recovery screen.
11.
Press the Power button to reboot the device.
5.
6.
3.
4.
1.
2.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
On the host computer, open a command prompt window and use the adb command: adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
7.
Type: adb reboot recovery
146
Application Deployment
8.
Press Enter. The System Recovery screen appears on the device.
9.
Press the Volume Up and Volume Down buttons to navigate to Apply upgrade from ADB .
10.
Press the Power button.
11.
Use the Volume Up and Volume Down buttons to navigate to Full OTA Package or Diff OTA Package .
12.
Press the Power button.
13.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
14.
Press Enter. The System Update installs (progress appears as percentage in the Command Prompt window) and then the System Recovery screen appears on the device.
15.
Press the Power button to reboot the device.
3.
4.
1.
2.
Go to Settings .
Touch About phone .
Scroll down to Build number .
Ensure that the build number matches the new system update package file number.
An Enterprise Reset erases all user data in the /data partition, including data in the primary storage locations ( /sdcard and emulated storage).
Before performing an Enterprise Reset, provision all necessary configuration files and restore after the reset.
Perform Enterprise Reset using device settings, or ADB.
1.
2.
3.
Go to Settings .
Touch System > Reset options > Erase all data (enterprise reset) .
Touch Erase all data twice to confirm the Enterprise Reset.
1.
2.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
Download the Enterprise Reset file to a host computer.
It is strongly recommended that prior to use, you must format the microSD card on the device.
1.
Copy the Enterprise Reset zip file to the root of the microSD card.
147
Application Deployment
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
2.
Press and hold the Power button until the menu appears.
3.
4.
Touch Restart .
Press and hold the Trigger button until the device vibrates. The System Recovery screen appears.
5.
6.
Press the Up and Down buttons to navigate to Apply upgrade from SD card .
Press the Enter button.
7.
8.
Use the Up and Down buttons to navigate to Full OTA Package .
Press the Enter button.
9.
Use the Up and Down buttons to navigate to the Enterprise Reset file.
10.
Press the Power button. The Enterprise Reset occurs and then the device returns to the Recovery screen.
11.
Press the Power button to reboot the device.
5.
6.
3.
4.
1.
2.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
Touch OK .
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
7.
8.
9.
Type: adb reboot recovery
Press Enter. The System Recovery screen appears on the device.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
148
Application Deployment
10.
Press Enter. The Enterprise Reset package installs and then the System Recovery screen appears on the device.
A Factory Reset erases all data in the /data and /enterprise partitions in internal storage and clears all device settings. A Factory Reset returns the device to the last installed operating system image. To revert
for more information.
To download the Factory Reset package:
1.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
2.
Download the appropriate Factory Reset file to a host computer.
1.
Copy the Factory Reset zip file to the root of the microSD card.
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
2.
Press and hold the Power button until the menu appears.
3.
4.
Touch Restart .
Press and hold the Trigger button until the device vibrates. The System Recovery screen appears.
5.
6.
Press the Up and Down buttons to navigate to Apply upgrade from SD card .
Press the Enter button.
7.
8.
Use the Up and Down buttons to navigate to Full OTA Package .
Press the Enter button.
9.
Use the Up and Down buttons to navigate to the Factory Reset file.
10.
Press the Power button. The Factory Reset occurs and then the device returns to the Recovery screen.
11.
Press the Power button to reboot the device.
To perform an Factory Reset using ADB:
1.
2.
3.
4.
Go to Settings .
Touch System > Advanced > Developer options .
Slide the switch to the ON position.
Touch USB Debugging . A check appears in the check box. The Allow USB debugging?
dialog box appears.
149
Application Deployment
5.
6.
Touch OK .
On the host computer, open a command prompt window and type: adb devices .
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device (where XXXXXXXXXXXXXXX is the device number).
NOTE: If device number does not appear, ensure that ADB drivers are installed properly.
7.
Type: adb reboot recovery
8.
9.
Press Enter. The System Recovery screen appears on the device.
On the host computer command prompt window type: adb sideload <file> where: <file> = the path and filename of the zip file.
10.
Press Enter. The Factory Reset package installs and then the System Recovery screen appears on the device.
The device contains the following types of file storage:
• Random Access Memory (RAM)
• Internal storage
• Enterprise folder.
Executing programs use RAM to store data. Data stored in RAM is lost upon a reset. The operating system manages how applications use RAM. It only allows applications and component processes and services to use RAM when required. It may cache recently used processes in RAM, so they restart more quickly when opened again, but it will erase the cache if it needs the RAM for new activities.
The screen displays the amount of used and free RAM.
• Performance - Indicates memory performance.
• Total memory - Indicates the total amount of RAM available.
• Average used (%) - Indicates the average amount of memory (as a percentage) used during the period of time selected (default - 3 hours).
• Free - Indicates the total amount of unused RAM.
• Memory used by apps - Touch to view RAM usage by individual apps.
Viewing Memory
1.
2.
Go to Settings .
Touch System > Advanced > Developer options > Memory .
150
Application Deployment
The device has internal storage. The internal storage content can be viewed and files copied to and from when the device is connected to a host computer. Some applications are designed to be stored on the internal storage rather than in internal memory.
Viewing Internal Storage
1.
2.
Go to Settings .
Touch Storage .
The device can have a removable microSD card. The microSD card content can be viewed and files copied to and from when the device is connected to a host computer.
Viewing External Storage
1.
2.
Go to Settings .
Touch Storage .
Portable storage displays the total amount of space on the installed and the amount used.
To unmount the microSD card, touch .
Touch S D card to view the contents of the card.
Formatting a microSD Card or USB Drive as Portable Storage
1.
4.
5.
2.
3.
Touch SD card or USB drive .
Touch > Storage settings .
Touch Format .
Touch ERASE & FORMAT .
Touch DONE .
Formatting a microSD Card as Internal Memory
4.
5.
2.
3.
You can format a microSD card as internal memory to increase the actual amount of the device’s internal memory. Once formatted, the microSD card can only be read by this device.
1.
Touch SD card .
Touch > Storage settings .
Touch Format as internal .
Touch ERASE & FORMAT .
Touch DONE .
151
Application Deployment
The Enterprise folder (within internal flash) is a super-persistent storage that is persistent after a reset and an Enterprise Reset. The Enterprise folder is erased during a Factory Reset. The Enterprise folder is used for deployment and device-unique data. The Enterprise folder is approximately 128 MB (formatted).
Applications can persist data after an Enterprise Reset by saving data to the enterprise/user folder. The folder is ext4 formatted and is only accessible from a host computer using ADB or from an MDM.
Apps use two kinds of memory: storage memory and RAM. Apps use storage memory for themselves and any files, settings, and other data they use. They also use RAM when they are running.
1.
2.
3.
4.
5.
Go to Settings .
Touch Apps & notifications .
Touch See all XX apps to view all apps on the device.
Touch > Show system to include system processes in the list.
Touch an app, process, or service in the list to open a screen with details about it and, depending on the item, to change its settings, permissions, notifications and to force stop or uninstall it.
Apps have different kinds of information and controls.
• Force stop - Stop an app.
• Disable - Disable an app.
• Uninstall - Remove the app and all of its data and settings from the device. See
Application on page 145 for information about uninstalling apps.
• Notifications - Set the app notification settings.
• Permissions - Lists the areas on the device that the app has access to.
• Storage & cache - Lists how much information is stored, and includes buttons for clearing it.
• Mobile data & Wi-Fi - Provides information about data consumed by an app.
• Advanced
• Screen time - Displays the amount of time the app has displayed on the screen.
• Battery - Lists the amount of computing power used by the app.
• Open by default - If you have configured an app to launch certain file types by default, you can clear that setting here.
• Display over other apps - allows an app to display on top of other apps.
• App details - Provides a link to additional app details on the Play store.
• Additional settings in the app - Opens settings in the app.
• Modify system settings - Allows an app to modify the system settings.
152
Application Deployment
Files and apps downloaded using the Browser or Email are stored on the Internal storage in the Download directory. Use the Downloads app to view, open, or delete downloaded items.
1.
Swipe the screen up and touch .
2.
3.
Touch > Downloads .
Touch and hold an item, select items to delete and touch . The item is deleted from the device.
153
The device has the following interchangeable modular keypads:
• 58-key Alpha Numeric Function keypad
• 53-key Standard keypad
• 53-key IBM-5250 Emulator keypad
• 53-key IBM-3270 Emulator keypad
• 53-key VT Emulator keypad
• 43-key Shifted Alpha keypad
• 34-key Numeric keypad
• 29-key Shifted Alpha keypad.
To support specialized applications, you can change the modular keypads in the field when required.
1.
2.
3.
Power off the device.
Remove the battery.
Using a Torx T8 screwdriver with a large grip, remove the two keypad latch screws from inside the battery slot.
154
1
Keypads
1 Keypad latch screws
4.
Slide the keypad latches toward the bottom of the device.
1
2
1
2
Screwdriver
Keypad latches
NOTE: If the keypad latches are hard to move, use a screwdriver to gently slide them towards the bottom of the device.
5.
Turn the device over so that the keypad is visible.
155
Keypads
6.
Using a Torx T8 screwdriver with a large grip, remove the two keypad assembly screws from the top of the keypad.
1
2
3
1
2
3
Keypad screws
Keypad microSD card holder
7.
8.
Lift the keypad from the device.
Align the keypad along the bottom ridge of the device, and then lay it flat.
156
Keypads
9.
Using a Torx T8 screwdriver with a large grip and a long shaft, secure the keypad to the device using the two screws. Torque screws to 5.8 kgf-cm or 5.0 lbf-in.
1
1 Keypad screws
10.
Turn the device over so that the keypad latches are visible.
11.
Slide both the keypad latches toward the top of the device.
1
1 Keypad latches
157
Keypads
\
12.
Using a Torx T8 screwdriver, replace the two keypad latch screws inside the battery slot and torque to
5.8 kgf-cm or 5.0 lbf-in.
1
1 Keypad latch screws
13.
Insert the battery.
14.
Press and hold the Power key to power on the device.
158
Keypads
The 58-key keypad contains a Power button, application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions can be changed by an application so the device’s keypad may not function exactly as described. See the Key
Descriptions table for key and button details, and the Keypad Special Functions table for the keypad’s various functions.
Figure 57 58-Keys Alpha Numeric Function Keypad
Table 11 58-Key Alpha Numeric Function Keypad Key Descriptions
Key
Power (Red)
P1
Turns the device on and off.
Description
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable key. By default, P1 is the dedicated PTT key.
Scan (Yellow) Activates the scanner/imager in a scan enabled application.
159
Keypads
Table 11 58-Key Alpha Numeric Function Keypad Key Descriptions (Continued)
Key Description
ESC Exits the current operation.
TAB
Up and Down
Left and Right
Alpha
BKSP
Tab function.
Moves up and down from one item to another.
Moves left and right from one item to another.
Use the alpha keys for alphabetic characters.
Backspace function.
SPACE Space function.
Numeric/Application The numeric keys generate keycodes 0 to 9.
Function (blue)
Control
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar.
Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the icon appears.
Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bar.
Press the Blue key followed by the CTRL key to activate the keypad alternate
ALT functions. The icon appears in the status bar.
160
Keypads
Table 11 58-Key Alpha Numeric Function Keypad Key Descriptions (Continued)
Shift
Key Description
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
Period/Decimal Point Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys.
Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix.
You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
Enter
This is the default symbol layout for this keyboard.
Executes a selected item or function.
161
Keypads
The 53-key keypad contains a Power button, application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions can be changed by an application so the device’s keypad may not function exactly as described. See the Key
Descriptions table for key and button details, and the Keypad Special Functions table for the keypad’s various functions.
Figure 58 53-Keys Standard Keypad
Table 12 53-Key Standard Keypad Key Descriptions
Key
Power (Red)
P1 / P2
Description
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable keys:
Scan (Yellow)
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
162
Keypads
Table 12 53-Key Standard Keypad Key Descriptions (Continued)
Key
Up and Down
Description
Moves up and down from one item to another.
Left and Right Moves left and right from one item to another.
ESC
Alpha
SPACE/BKSP
Numeric/Application
Exits the current operation.
Use the alpha keys for alphabetic characters.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9.
Function (blue)
Control
Shift
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar.
Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the icon appears.
Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bar.
Press the Blue key followed by the CTRL key to activate the keypad alternate
ALT functions. The icon appears in the status bar.
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
163
Keypads
Table 12 53-Key Standard Keypad Key Descriptions (Continued)
Key Description
Period/Decimal Point Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys.
Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix.
You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
Enter
This is the default symbol layout for this keyboard.
Executes a selected item or function.
164
Keypads
The IBM-5250 emulator keypad contains a Power button, application keys, scroll keys and a function key.
The keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions can be changed by an application so the device’s keypad may not function exactly as described. See the
Key Descriptions table for key and button details, and the Keypad Special Functions table for the keypad’s various functions.
Figure 59 53-Keys IBM-5250 Emulator Keypad
NOTE: The IBM-5250 emulator configuration is only used when the device is running the 5250 emulation software.
Table 13 IBM-5250 Emulator Descriptions
Key
Power (red)
P1/P2
Scan (yellow)
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable keys:
Description
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
165
Keypads
Table 13 IBM-5250 Emulator Descriptions (Continued)
Key
Up and Down
Description
Moves up and down from one item to another.
Left and Right Moves left and right from one item to another.
ENT
Alpha
SPACE/BKSP
Application
Function (blue)
Control
Shift
The enter key.
Use the alpha keys for alphabetic characters.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9.
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the
Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the icon appears.
Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bars.
Press the Blue key followed by the CTRL key to activate the keypad alternate ALT functions. The icon appears in the status bar.
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
166
Keypads
Table 13 IBM-5250 Emulator Descriptions (Continued)
Key
Period/Decimal Point
Description
Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
FIELD_EXIT
This is the default symbol layout for this keyboard.
Executes a selected item or function.
167
Keypads
The IBM-3270 emulator keypad contains a Power button, application keys, scroll keys and a function key.
The keypad is color-coded to indicate the alternate function key (blue, green, orange) values. Note that keypad functions can be changed by an application so the device’s keypad may not function exactly as described. See the Key Descriptions table for key and button details.
Figure 60 53-Keys IBM-3270 Emulator Keypad
NOTE: The IBM-3270 emulator configuration is only used when the device is running the 3270 emulation software.
Table 14 IBM-3270 Emulator Descriptions
Key
Power (red)
P1/P2
Scan (yellow)
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable keys:
Description
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
168
Keypads
Table 14 IBM-3270 Emulator Descriptions (Continued)
Key
Up and Down
Description
Moves up and down from one item to another.
Left and Right Moves left and right from one item to another.
CLR
Alpha
SPACE/BKSP
Application
Function (Blue)
Control
Shift
The clear key.
Use the alpha keys for alphabetic characters.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9.
Press and release the Blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the
Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the icon appears.
Press and release the CTRL key to activate the keypad alternate CTRL functions (shown on the keypad in Green). The icon appears in the status bars.
Press the Blue key followed by the CTRL key to activate the keypad alternate ALT functions. The icon appears in the status bar.
Press and release the SHIFT key to activate the keypad alternate SHIFT functions (shown on the keypad in Orange). The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
169
Keypads
Table 14 IBM-3270 Emulator Descriptions (Continued)
Key
Period/Decimal Point
Description
Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
ENTER
This is the default symbol for this keyboard.
Executes a selected item or function.
170
Keypads
The VT emulator keypad contains a Power button, application keys, scroll keys and a function key. The keypad is color-coded to indicate the alternate function key (blue) values. Note that keypad functions can be changed by an application so the device’s keypad may not function exactly as described. See the Key
Descriptions table for key and button details, and the Keypad Special Functions table for the keypad’s various functions.
Figure 61 53-Keys VT Emulator Keypad
NOTE: The VT emulator configuration is only used when the device is running the VT emulation software.
Table 15 VT Emulator Descriptions
Power (red)
Key
P1/P2 User programmable keys:
Description
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
Scan (yellow)
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
171
Keypads
Table 15 VT Emulator Descriptions (Continued)
Key
Up and Down
Description
Moves up and down from one item to another.
Left and Right Moves left and right from one item to another.
ESC
Alpha
SPACE/BKSP
Application
Function (blue)
Control
Shift
Exits the current operation.
Use the alpha keys for alphabetic characters.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9. These keys can also be assigned to an application.
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the
Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the
icon appears.
Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bar.
Press the Blue key followed by the CTRL key to activate the keypad alternate ALT functions. The icon appears in the status bar.
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
172
Keypads
Table 15 VT Emulator Descriptions (Continued)
Key
Period/Decimal Point
Description
Produces a period for alpha entries and decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
Enter
This is the default symbol layout for this keyboard.
Executes a selected item or function.
173
Keypads
The 43-key keypad contains a Power button, application keys, scroll keys and a function key. The keypad is color-coded to indicate the alternate function key (blue) values and the alternate ALPHA key (orange) values. Note that keypad functions can be changed by an application so the MC93XX’s keypad may not function exactly as described. See the Key Descriptions table for key and button details, and the Keypad
Special Functions table for the keypad’s various functions.
Figure 62 43-Keys Shifted Alpha Keypad
Table 16 43 Shifted Alpha Descriptions
Key
Power (red)
P1/P2
Scan (yellow)
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable keys:
Description
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
174
Keypads
Table 16 43 Shifted Alpha Descriptions (Continued)
Key
Up and Down
Description
Moves up and down from one item to another.
Left and Right
ESC
CTRL
ALT
SPACE/BKSP
Application
Function (Blue)
Function (Orange)
Moves left and right from one item to another.
Exits the current operation.
Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bars.
Press the Blue key followed by the CTRL key to activate the keypad alternate ALT functions. The icon appears in the status bar.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9.
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the
Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the
icon appears.
Press and release the blue function key to activate the alpha key functions
(shown on the keypad in Orange).
Press and release the Orange function key to activate the keypad alternate functions (shown on the keypad in Orange). Press the Orange function key once to put the keyboard into one-shot mode. The icon appears on the
Status bar. Press the Orange function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the Orange function key a third time to return to the default keypad functions, and the icon clears.
175
Keypads
Table 16 43 Shifted Alpha Descriptions (Continued)
Key
Shift
Period/Decimal Point
Description
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
Enter
This is the default symbol layout for this keyboard.
Executes a selected item or function.
176
Keypads
The 34-key keypad contains a Power button, application keys, scroll keys and a function key. The keypad is color-coded to indicate the alternate function key (blue) values and the alternate Shift key values. Note that keypad functions can be changed by an application so the MC93XX’s keypad may not function exactly as described. See the Key Descriptions table for key and button details.
Figure 63 34-Keys Numeric Keypad
177
Keypads
Table 17 34-Keys Descriptions
Key
Power (red)
Diamond
Turns the device on and off.
Description
Performs a warm boot and a hard reset. See Resetting the Device for more information.
Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
ESC
TAB
Scan (yellow)
Up and Down
BKSP
Application
This is the default symbol layout for this keyboard.
Exits the current operation.
Tab function.
Activates the scanner/imager in a scan enabled application.
Moves up and down from one item to another.
Space and backspace functions.
The numeric keys generate keycodes 0 to 9.
178
Keypads
Table 17 34-Keys Descriptions (Continued)
Key
Function (blue)
Description
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the
Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the Blue key followed by the CTRL key to activate the keypad alternate ALT functions. The icon appears in the status bar.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the
icon appears.
CTRL Press and release the CTRL key to activate the keypad alternate CTRL functions. The icon appears in the status bars.
Shift
Period/Decimal Point
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
Produces a period for alpha entries and a decimal point for numeric entries.
ENT Executes a selected item or function.
179
Keypads
The 29-key keypad contains a Power button, application keys, scroll keys and a function key. Note that keypad functions can be changed by an application so the MC93XX’s keypad may not function exactly as described. See the Key Descriptions table for key and button details, and the Keypad Special Functions table for the keypad’s various functions.
Figure 64 29-Keys Keypad
Table 18 29-Keys Descriptions
Key
Power (red)
P1/P2
Scan (yellow)
Turns the device on and off.
Performs a warm boot and a hard reset. See Resetting the Device for more information.
User programmable keys:
Description
• By default, P1 is the dedicated PTT key.
• By default, P2 acts like another Scan key.
Activates the scanner/imager in a scan enabled application.
Up and Down Moves up and down from one item to another.
180
Keypads
Table 18 29-Keys Descriptions (Continued)
Key
Left and Right
Description
Moves left and right from one item to another.
ESC
Shift
BKSP
TAB
Application
Application
Function (Blue)
Function (Orange)
Exits the current operation.
Press and release the SHIFT key to activate the keypad alternate SHIFT functions. The icon appears in the status bar. After pressing another key, the keypad returns to the non-shift state.
Press and release the SHIFT key twice to enable the Shift Lock state. The
icon appears in the status bar. Press and release the SHIFT key again to disable the Shift Lock state.
Backspace function.
Tab function.
The numeric keys generate keycodes 0 to 9.
The application keys.
Press and release the blue function key to activate the keypad alternate functions (shown on the keypad in Blue). Press the Blue function key once to put the keyboard into one-shot mode. The icon appears on the Status bar. Press the Blue function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the
Blue function key a third time to return to the default keypad functions, and the icon clears.
Press the blue function key and SHIFT to activate CAPSLOCK mode, the
icon appears.
Press and release the blue function key to activate the alpha key functions
(shown on the keypad in Orange).
Press and release the Orange function key to activate the keypad alternate functions (shown on the keypad in Orange). Press the Orange function key once to put the keyboard into one-shot mode. The icon appears on the
Status bar. Press the Orange function key again the keypad is locked in function mode, and the icon appears in the Status bar. Press and release the Orange function key a third time to return to the default keypad functions, and the icon clears.
181
Keypads
Table 18 29-Keys Descriptions (Continued)
Key
Period/Decimal Point
Description
Produces a period for alpha entries and a decimal point for numeric entries.
Diamond Provides a 3x3 matrix on the screen with nine additional symbols. With a single tap you can select via touch input or the keyboard, 1-9 numerical keys. Double tapping the Diamond key locks the 3x3 grid, and you can select multiple keys. Pressing the Diamond key a third time closes the 3x3 matrix. You can modify the symbols in the 3x3 matrix using the StageNow utility in the KeyMappingMgr settings.
Enter
This is the default symbol layout for this keyboard.
Executes a selected item or function.
182
Keypads
The keypad special functions are color coded on the keypads. For example, on the 53-key keypad, the display backlight icon is blue indicating that the blue function key must be selected first to access the display backlight.
Table 19 Keypad Special Functions
Icon
43 Key
29 Key
Decreases the keyboard backlight intensity.
Increases the keypad backlight intensity.
Increases display backlight intensity.
Decreases display backlight intensity.
Increases overall system volume.
Decreases overall system volume.
Enables Alt keypad functions.
Only applicable if the Large Key
Indicator is enabled.
Caps Lock
Blue key+Y Blue key + X Keylight+Down Blue key+F10 Blue key+7
Blue key+Z Blue key + Y Keylight+Up
Blue key+N Blue key + D Blue key+F1
Blue key+M Blue key + I Blue key+F5
Blue key+R Blue key + H Blue key+F4
Blue key+Q Blue key + M Blue key+F8
Blue key+CTRL
Blue key+SHIFT
Blue key +
CTRL
BLUE +
SHIFT
ALT
Blue key+SHIFT
Blue key+F11 Blue key+9
Blue key+F1
Blue key+F5
Blue key+F4
Blue key+F8
Blue key+
CTRL
Blue key
SHIFT
Blue key+7
Blue key+4
Blue key+3
Blue key+2
Sends TAB character
(forward tab).
TAB Blue key +
Space
Blue key+SPACE
TAB TAB
183
Keypads
NOTE: Use of display and keypad backlighting can significantly reduce battery life.
184
Keypads
The keypads can be selected as necessary to support specialized applications. The keypads contain a
Power button, application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function key (blue/orange) values. The following table details special character generation.
Characters can also be generated using the keyboard input panel.
NOTE: Shift-1 through Shift-0 only applies to the Standard 53-key keyboard. On the 5250, 3270, and VT
53-key keyboards the Shift + <num> combinations generate F11-F20 keys.
Table 20 Special Character Generation Map
43 Key 29 Key
[ (open square bracket)
] (close square bracket)
/ (forward slash)
\ (backslash)
= (equal sign)
; (semi-colon)
` (apostrophe)
, (comma)
. (period)
! (exclamation sign)
@ (at sign)
# (pound sign)
$ (dollar sign)
% (percent sign)
^ (carat)
& (ampersand)
* (asterisk)
( (open parenthesis)
Diamond+2 Blue Key+E
Diamond+3 Blue Key+F
Shift+1
Shift+2
Shift+3
Shift+4
Shift+5
Shift+6
Shift+7
Shift+8
Not
Applicable
Not
Applicable
Not
Applicable
Blue Key+V
Blue Key+G
Blue Key+W
Not
Applicable
Not
Applicable
Blue Key+R
Blue Key+J
Shift+. (Dot) Blue Key+A
Dot Blue Key+B
Shift+9
Shift+1
Shift+2
Shift+3
Shift+4
Shift+5
Shift+6
Shift+7
Blue Key+U
Shift+8
Shift+9
Diamond+8
Diamond+9
Diamond+2
Diamond+3
Blue Key+F12 Not
Applicable
Not Applicable Not
Applicable
Blue Key+Bksp Not
Applicable
Not Applicable Not
Applicable
Not Applicable Not
Applicable
Not Applicable Blue Key+.
(Dot)
Not Applicable Dot
Shift+1 Shift+1
Shift+2
Shift+3
Shift+4
Shift+5
Shift+6
Shift+7
Blue Key+F11,
Shift+8
Shift+9
Shift+2
Shift+3
Shift+4
Shift+5
Shift+6
Shift+7
Shift+8
Shift+9
Shift+2
Shift+3
Shift+4
Shift+5
Shift+6
Shift+7
Shift+8
Diamond+
8
Diamond+
9
Blue
Key+8
Not
Applicable
Blue
Key+5
Diamond+
5
Not
Applicable
Not
Applicable
Not
Applicable
Shift+1
Shift+9
185
Keypads
Table 20 Special Character Generation Map (Continued)
43 Key 29 Key
) (close parenthesis)
' (single quote)
" (double quote)
+ (plus sign)
Shift+0
Not
Applicable
Not
Applicable
Not
Applicable
Shift+0
Blue Key+C
Shift+0 Shift+0
Not Applicable Not
Applicable
Shift+Blue Key+C Not Applicable Not
Applicable
Blue Key+S Blue Key+F9 Not
Applicable
Shift+0
Not
Applicable
Not
Applicable
Orange
Key+ -
(Minus)
Minus key - (dash) Not
Applicable
: (colon)
< (less than sign)
> (greater than sign)
Diamond+5
Shift+Blue
Key+. (Dot)
Shift+. (Dot)
Shift+Blue Key+R
Shift+Blue Key+A
Shift+Blue Key+B
Diamond+5
Not Applicable
Shift+. (Dot)
Diamond+5
Shift + Blue
Key+. (Dot)
Diamond+
6
Shift+
Orange
Key+ .
(Dot)
Shift+. (Dot) Shift+.
(Dot)
? (question mark) Not
Applicable
_ (underscore) Diamond+9
Blue Key+N,
Blue Key+T
Blue Key+F10
Shift+Blue Key+V Shift+Blue
Key+F12
Shift+Blue Key+N Diamond+3
Not
Applicable
Not
Applicable
Diamond+9
Shift
+Blue
Key+8
Shift + -
(Minus)
{ (open curly bracket)
} (close curly bracket)
~ (tilde)
| (pipe)
Not
Applicable
Not
Applicable
Shift+Blue Key+E Not Applicable
Shift+Blue Key+F Not Applicable Not
Diamond+7 Shift+Blue Key+J Diamond+1
Not
Applicable
Applicable
Diamond+7
Diamond+1 Shift+Blue Key+G Diamond+7 Diamond+1
Not
Applicable
Not
Applicable
Not
Applicable
Not
Applicable
186
For trouble-free service, observe the following tips when using the device:
• To avoid scratching the screen, use a Zebra approved capacitive compatible stylus intended for use with a touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the device screen.
• The touch-sensitive screen of the device is glass. Do not drop the device or subject it to strong impact.
• Protect the device from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
• Do not store the device in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the device. If the surface of the device screen becomes soiled, clean it with a soft cloth moistened with an approved cleanser. For a list of approved cleansers, see Approved Cleanser Active
Ingredients.
• Periodically replace the rechargeable battery to ensure maximum battery life and product performance. Battery life depends on individual usage patterns.
• The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in this guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the ambient battery and charger temperatures must be between +32ºF and +104ºF (0ºC and +40ºC).
• Do not use incompatible batteries and chargers, including non-Zebra batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact the Global Customer Support Center.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred the battery.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
187
Maintenance and Troubleshooting
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to properly dispose of used rechargeable batteries.
• Do not dispose of batteries in fire.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with water for 15 minutes, and seek medical advice.
• If you suspect damage to your equipment or battery, contact Customer Support to arrange for inspection.
CAUTION: Always wear eye protection.
Read warning label on alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support
Center for more information.
WARNING: Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite 1 (see important note below) , or mild dish soap.
IMPORTANT: Use pre-moistened wipes and do not allow liquid cleaner to pool.
1 When using sodium hypochlorite (bleach) based products, always follow the manufacturer’s recommended instructions: use gloves during application and remove the residue afterwards with a damp alcohol cloth or a cotton swab to avoid prolonged skin contact while handling the device.
Due to the powerful oxidizing nature of sodium hypochlorite, the metal surfaces on the device are prone to oxidation (corrosion) when exposed to this chemical in the liquid form (including wipes). In the event that these type of disinfectants come in contact with metal on the device, prompt removal with an alcohol-dampened cloth or cotton swab after the cleaning step is critical.
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; aqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device.
188
Maintenance and Troubleshooting
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, instead gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Before use, allow the unit to air dry.
NOTE: For thorough cleaning, it is recommended to first remove all accessory attachments, such as hand straps or cradle cups, from the mobile device and to clean them separately.
Do not handle the device while wearing vinyl gloves containing phthalates. Remove vinyl gloves and wash hands to eliminate any residue left from the gloves.
If products containing any of the harmful ingredients listed above are used prior to handling the device, such as a hand sanitizer that contains ethanolamine, hands must be completely dry before handling the device to prevent damage to the device.
IMPORTANT: If the battery connectors are exposed to cleaning agents, thoroughly wipe off as much of the chemical as possible and clean with an alcohol wipe. It is also recommended to install the battery in the terminal prior to cleaning and disinfecting the device to help minimize buildup on the connectors.
When using cleaning/disinfectant agents on the device, it is important to follow the directions prescribed by the cleaning/disinfectant agent manufacturer.
• Alcohol wipes
• Lens tissue
• Cotton-tipped applicators
• Isopropyl alcohol
• Can of compressed air with a tube.
The cleaning frequency is at the customer’s discretion due to the varied environments in which the mobile devices are used and may be cleaned as frequently as required. When dirt is visible, it is recommended to clean the mobile device to avoid build up of particles which make the device more difficult to clean later on.
Housing
Thoroughly wipe the housing, including all buttons and triggers, using an approved alcohol wipe.
Display
The display can be wiped down with an approved alcohol wipe, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
189
Maintenance and Troubleshooting
Exit Window
Wipe the exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
4.
5.
1.
2.
3.
6.
Remove the main battery from the mobile computer.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
To remove any grease or dirt, rub the cotton portion of the cotton-tipped applicator back-and-forth across the connectors on the battery and terminal sides. Do not leave any cotton residue on the connectors.
Repeat at least three times.
Use a dry cotton-tipped applicator and repeat steps 3 and 4. Do not leave any cotton residue on the connectors.
Inspect the area for any grease or dirt and repeat the cleaning process if necessary.
CAUTION: After cleaning the battery connectors with bleach-based chemicals, follow the Battery
Connector Cleaning instructions to remove bleach from the connectors.
1.
2.
3.
4.
5.
6.
7.
Remove the DC power cable from the cradle.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
All sides of the connector should also be rubbed with the cotton-tipped applicator.
Remove any lint left by the cotton-tipped applicator.
If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and low humidity requires less drying time.
CAUTION: After cleaning the cradle connectors with bleach-based chemicals, follow the Cleaning Cradle
Connectors instructions to remove bleach from the connectors.
The following tables provides typical problems that might arise and the solution for correcting the problem.
190
Maintenance and Troubleshooting
Table 21 Troubleshooting the MC93XX
Problem
When pressing the power button the device does not turn on.
When pressing the power button the device does not turn on but LED bar blinks.
Battery did not charge.
Cause
Battery not charged.
Battery not installed properly.
System crash.
Battery charge is at a level where data is maintained but battery should be re-charged.
Cannot see characters on display.
During data communication with a host computer, no data transmitted, or transmitted data was incomplete.
Battery failed.
Device removed from cradle while battery was charging.
Replace battery. If the device still does not operate, perform a reset.
Insert device in cradle. The 7,000 mAh battery fully charges in less than five hours at room temperature.
Extreme battery temperature.
Battery does not charge if ambient temperature is below 0°C (32°F) or above 40°C (104°F).
Device not powered on. Press the Power button.
Device removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Communication software was incorrectly installed or configured.
Wi-Fi radio is not on.
You moved out of range of an access point.
Solution
Charge or replace the battery in the device.
Install the battery properly.
Perform a reset.
Charge or replace the battery in the device.
Replace the device in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Perform setup.
Turn on the Wi-Fi radio.
Move closer to an access point.
During data communication over
Wi-Fi, no data transmitted, or transmitted data was incomplete.
During data communication over
Bluetooth, no data transmitted, or transmitted data was incomplete.
No sound.
Bluetooth radio is not on.
You moved out of range of another Bluetooth device.
Volume setting is low or turned off.
Turn on the Bluetooth radio.
Move within 10 meters (32.8 feet) of the other device.
Adjust the volume.
191
Maintenance and Troubleshooting
Table 21 Troubleshooting the MC93XX (Continued)
Problem
Device shuts off.
Cause
Device is inactive.
Battery is depleted.
The device is not responding.
Solution
The display turns off after a period of inactivity. Set this period to 15 seconds, 30 seconds, 1, 2, 5, 10 or
30 minutes.
Replace the battery.
Reset the device.
Tapping the window buttons or icons does not activate the corresponding feature.
A message appears stating that the device memory is full.
The device does not decode with reading bar code.
Too many files stored on the device.
Too many applications installed on the device.
Scanning application is not loaded.
Unreadable bar code.
Distance between exit window and bar code is incorrect.
Device is not programmed for the bar code.
Device is not programmed to generate a beep.
Battery is low.
Delete unused memos and records. If necessary, save these records on the host computer (or use an
SD card for additional memory).
Remove user-installed applications on the device to recover memory. Select > Storage > FREE UP
SPACE > REVIEW RECENT ITEMS . Select the unused program(s) and tap FREE UP .
Load a scanning application on the device or enable
DataWedge. See the system administrator.
Ensure the symbol is not defaced.
Place the device within proper scanning range.
Program the device to accept the type of bar code being scanned. Refer to the EMDK or DataWedge application.
If the device does not beep on a good decode, set the application to generate a beep on good decode.
Device cannot find any Bluetooth devices nearby.
Cannot unlock device.
Too far from other
Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
The Bluetooth device(s) are not in discoverable mode.
User enters incorrect password.
If the scanner stops emitting a laser beam upon a trigger press, check the battery level. When the battery is low, the scanner shuts off before the device low battery condition notification. Note: If the scanner is still not reading symbols, contact the distributor or the Global Customer Support Center.
Move closer to the other Bluetooth device(s), within a range of 10 meters (32.8 feet).
Turn on the Bluetooth device(s) to find.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
If you enter an incorrect password eight times, you are requested to enter a code before trying again.
If you forgot the password, contact your system administrator.
192
Maintenance and Troubleshooting
Table 21 Troubleshooting the MC93XX (Continued)
Battery pack communication error.
Problem Cause
The battery is not inserted properly.
The battery is properly inserted, however, when the terminal is in an active vibration environment or has fallen from a high vantage point (more than 8 ft), it might interrupt battery communication.
The battery communication pin is damaged.
Solution
Remove and reinsert the battery into the device.
Remove and reinsert the battery into the device.
Remove the battery and insert a new battery into the device.
Table 22 Troubleshooting the 1-Slot USB Charging Cradle
Symptom
LEDs do not light when device or spare battery is inserted.
Device battery is not charging.
Possible Cause
Cradle is not receiving power.
Device is not seated firmly in the cradle.
Spare battery is not seated firmly in the cradle.
Device was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
The device is not fully seated in the cradle.
Extreme battery temperature.
Action
Ensure the power cable is connected securely to both the cradle and to AC power.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Remove and re-insert the spare battery into the charging slot, ensuring it is firmly seated.
Ensure cradle is receiving power. Ensure device is seated correctly. Confirm main battery is charging.
The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to
100% in approximately three hours.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 5°C (40°F) or above 40°C (104°F).
193
Maintenance and Troubleshooting
Table 22 Troubleshooting the 1-Slot USB Charging Cradle (Continued)
Symptom
Spare battery is not charging.
Possible Cause
Battery not fully seated in charging slot.
Battery inserted incorrectly.
Battery is faulty.
Action
Remove and re-insert the spare battery in the cradle, ensuring it is firmly seated. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to
100% in approximately three hours.
Re-insert the battery so the charging contacts on the battery align with the contacts on the cradle.
Verify that other batteries charge properly. If so, replace the faulty battery.
Table 23 Troubleshooting the 4-Slot Charge Only Cradle
Problem
Battery is not charging.
Cause
Device removed from the cradle too soon.
Solution
Replace the device in the cradle. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to 100% in approximately three hours.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Device is not inserted correctly in the cradle.
Remove the device and reinsert it correctly. Verify charging is active. Touch > view battery status.
System > About phone > Status to
Ambient temperature of the cradle is too warm.
Move the cradle to an area where the ambient temperature is between 5°C (40°F) or above 40°C (104°F).
194
Maintenance and Troubleshooting
Table 23 Troubleshooting the 4-Slot Charge Only Cradle
Problem
Spare Battery not charging.
Cause
Charger is not receiving power.
Spare battery is not correctly seated.
Battery adapter is not seated properly.
Ensure the power cable is connected securely to both the charger and to AC power.
Solution
Remove and re-insert the battery into the battery adapter, ensuring it is correctly seated.
Remove and re-insert the battery adapter into the charger, ensuring it is correctly seated.
Battery was removed from the charger or charger was unplugged from
AC power too soon.
Ensure charger is receiving power. Ensure the spare battery is seated correctly. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to 100% in approximately three hours.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Table 24 Troubleshooting the 4-Slot Ethernet Cradle
Problem
During communication, no data transmits, or transmitted data was incomplete.
Battery is not charging.
Cause
Device removed from cradle during communications.
Incorrect cable configuration.
Device has no active connection.
Device removed from the cradle too soon.
Solution
Replace device in cradle and retransmit.
Ensure that the correct cable configuration.
An icon is visible in the status bar if a connection is currently active.
Replace the device in the cradle. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to 100% in approximately three hours.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
Device is not inserted correctly in the cradle.
Remove the device and reinsert it correctly. Verify charging is active. Touch >
Status to view battery status.
System > About phone >
Ambient temperature of the cradle is too warm.
Move the cradle to an area where the ambient temperature is between 5°C (+40°F) and +40°C
(+104°F).
195
Maintenance and Troubleshooting
Table 25 Troubleshooting the 4-Slot Battery Charger
Problem
Spare Battery
Charging LED does not light when spare battery is inserted.
Spare Battery not charging.
Cause
Spare battery is not correctly seated.
Solution
Remove and re-insert the spare battery into the charging slot, ensuring it is correctly seated.
Charger is not receiving power.
Spare battery is not correctly seated.
Battery adapter is not seated properly.
Battery was removed from the charger or charger was unplugged from
AC power too soon.
Ensure the power cable is connected securely to both the charger and to AC power.
Remove and re-insert the battery into the battery adapter, ensuring it is correctly seated.
Remove and re-insert the battery adapter into the charger, ensuring it is correctly seated.
Ensure charger is receiving power. Ensure the spare battery is seated correctly. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to 100% in approximately three hours.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Table 26 Troubleshooting the 16-Slot Battery Charger
Problem
Spare Battery
Charging LED does not light when spare battery is inserted.
Cause
Spare battery is not correctly seated.
Solution
Remove and re-insert the spare battery into the charging slot, ensuring it is correctly seated.
196
Maintenance and Troubleshooting
Table 26 Troubleshooting the 16-Slot Battery Charger (Continued)
Problem
Spare Battery not charging.
Cause
Charger is not receiving power.
Spare battery is not correctly seated.
Battery adapter is not seated properly.
Ensure the power cable is connected securely to both the charger and to AC power.
Solution
Remove and re-insert the battery into the battery adapter, ensuring it is correctly seated.
Remove and re-insert the battery adapter into the charger, ensuring it is correctly seated.
Battery was removed from the charger or charger was unplugged from
AC power too soon.
Ensure charger is receiving power. Ensure the spare battery is seated correctly. The battery charges from fully depleted to 90% in approximately 2.5 hours, and from fully depleted to 100% in approximately three hours.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
197
For device technical specifications, go to www.zebra.com
.
The table below lists the typical distances for selected barcode densities. The minimum element width (or
“symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol.
Table 27 SE965 Decode Distances
5.0 mil
Code 128
5.0 mil
Code 39
7.5 mil
Code 39
10 mil
Code 128
13 mil
100% UPC
15 mil
Code 128
20 mil
Code 39
Barcode Content/ Contrast Note 1
1234
80% MRD
ABCDEFGH
80% MRD
ABCDEF
80% MRD
1234
80% MRD
012345678905
80% MRD
1234
80% MRD
123
80% MRD
1.1 in
2.79 cm
1.2 in
3.05 cm
Note 3
1.6 in
4.06 cm
1.0 in
2.54 cm
Note 3
1.4 in
3.56 cm
Note 3
1.2 in
3.05 cm
1.2 in
3.05 cm
Typical Working Ranges
Near Far
7.7 in
19.56 cm
12.5 in
31.75 cm
18.5 in
46.99 cm
19.0 in
48.26 cm
27.0 in
68.58 cm
29.5 in
74.93 cm
52.0 in
132.08 cm
198
Specifications
Table 27 SE965 Decode Distances (Continued)
55 mil
Code 39
100 mil
Code 39
Barcode Content/ Contrast Note 1
CD
80% MRD
123456
80% MRD
31.4 in
8.64 cm
Note 3
2.0 ft
60.96 cm
Note 3
Typical Working Ranges
Near Far
100.0 in
254.0 cm
17 ft
518.16 cm
1. Contrast is measured as Mean Reflective Difference (MRD) at 650 nm.
2. Working range specifications at temperature = 23°C, pitch=18°, roll=0°, skew=0°, photographic quality, ambient light ~150 ft-c, humidity 45-70% RH.
3. Dependent upon width of barcode.
4. Distances measured from front edge of scan engine chassis.
The table below lists the typical distances for selected barcode densities. The minimum element width (or
“symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol.
Table 28 SE4750-SR Decode Distances
Symbol Density/ Barcode Type
3.0 mil
Code 39
5.0 mil
Code 128
5.0 mil
PDF417
6.67 mil
PDF417
10. mil
Data Matrix
100% UPCA
15 mil
Code 128
20 mil
Code 39
3.7 in
9.3 cm
3.2 in
8.12 cm
4.0 in
10.16 cm
2.9 in
7.36 cm
3.0 in
7.62 cm
1.8 in
4.57 cm
Note 2
2.4 in
6.10 cm
1.6 in
4.06 cm
Near
Typical Working Ranges
5.4 in
13.71 cm
7.6 in
19.30 cm
7.0 in
17.78 cm
9.0 in
22.86 cm
9.4 in
23.87 cm
20.0 in
50.8 cm
Far
22.0 in
55.88 cm
30.0 in
76.2 cm
199
Specifications
The table below lists the typical distances for selected bar code densities.
Table 29 SE4770-SR Decode Distances
3 mil Code 39
5 mil Code 128
5 mil PDF417
Symbology
6.67 mil PDF 417
10 mil DataMatrix
100% UPCA
15 mil Code 128
2.8 in.
7.11 cm
2.3 in.
5.84 cm
3.0 in.
7.62 cm
2.2 in.
5.58 cm
2.4 in.
6.09 cm
1.6 in.
4.06 cm
2.4 in.
6.09* cm
Near
Typical Working Range
5.8 in.
14.73 cm
9.8 in.
24.89 cm
7.9 in.
20.06 cm
10.1 in.
25.65 cm
11.0 in.
27.94 cm
24.9 in.
63.24 cm
27.8 in.
70.61 cm
20 mil Code 39
20 mil QR
1.6 in.
4.06 cm
1.1 in.
2.79 cm
36.1 in.
91.69 cm
17.5 in.
44.45 cm
* Limited by width of bar code in field of view. See SE4770 Integration Guide for details.
Far
Photographic quality bar code at 18° tilt pitch angle under 30 fcd ambient illumination. Distances measured from front edge of scan engine chassis.
The table below lists the typical distances for selected barcode densities. The minimum element width (or
“symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol.
Table 30 SE4850-ER Decode Distances
Symbol Density/ Barcode Type
10 mil Code 39
13 100% UPC
15 mil Code 128
5.0 in. *
12.7 cm *
Typical Working Ranges @20 Ft-Cd Minimum
Near Far
62.0 in.
157.48 cm
7.0 in.
17.78 cm
10.0 in. *
25.4 cm *
77.0 in.
195.58 cm
86.0 in.
218.44 cm
200
Specifications
Table 30 SE4850-ER Decode Distances (Continued)
Symbol Density/ Barcode Type
20 mil Code 39
40 mil Code 39
55 mil Code 39
100 mil Code 39 (paper)
100 mil Code 39 (reflective)
DataMatrix 10
DataMatrix 55
Typical Working Ranges @20 Ft-Cd Minimum
Near Far
8.0 in. *
20.32 cm *
9.0 in. *
22.86 cm *
137.0 in.
347.98 cm
298.0 in. **
756.92 cm **
11.0* in. *
27.94* cm *
21.0* in. *
53.34* cm *
42.0 in. *
106.68 cm *
6.0 in.
15.24 cm
7.0 in.
17.78 cm
378.0 in. **
960.12 cm **
600.0 in. **
1524 cm **
600.0 in.
1524.0 cm
38.0 in.
96.52 cm
200.0 in.
508.0 cm
DataMatrix 300 (reflective)
15 mil Code 128 (4 in. wide)
23.0 in.
58.42 cm
8.0 in. *
20.32 cm *
* Limited by width of bar code in field of view.
516.0 in.
1310.64 cm
86.0 in.
218.44 cm
** Range is reduced under low ambient light level.
201
P9 P1
Specifications
Table 31 I/O Connector Pin-Outs
7
8
9
5
6
3
4
1
Pin
2
Ground
USB D-
Signal
USB D+
USB PWR
Batt_Det_C
Cradle_PWR
USB_CC2
USB_CC1
GND
Description
Ground pin connected to the Cradle or USB Charge Cable ground.
USB OTG data signal negative.
USB OTG data signal positive.
Power supply from USB Charging Cable.
Connected with 1k Ω resistor to Ground in the battery pack.
DC Power supply from the Cradle.
Used by USB_CC2 following USB type-C specification for USB 2.0.
Used by USB_CC1 following USB type-C specification for USB 2.0.
Ground pin connected to the Cradle or USB Charge Cable ground.
202
Specifications
Table 32 1-Slot USB Charge Cradle with Spare Battery Charger Technical Specifications
Dimensions
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Item
Electrostatic Discharge (ESD)
Description
Height: 87.9 mm (3.46 in)
Width: 152.4 mm (6.00 in)
Depth: 159.4 mm (6.28 in)
522 g (18.41 oz)
12 VDC
28 watts
0°C to 40°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
+/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
Table 33 4-Slot Charge Only ShareCradle Technical Specifications
Dimensions
Weight
Input Voltage
Item
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Height: 116.5 mm (4.59 in)
Width: 152.4 mm (6.00 in)
Depth: 132.7 mm (5.22 in)
Description
1879 g (66.28 oz)
12 VDC
63 watts
0°C to 40°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
203
Specifications
Table 33 4-Slot Charge Only ShareCradle Technical Specifications (Continued)
Humidity
Drop
Item
Electrostatic Discharge (ESD)
5% to 95% non-condensing
Description
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
+/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
Table 34 4-Slot Ethernet ShareCradle Technical Specifications
Item
Dimensions
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge (ESD)
Height: 116.5 mm (4.59 in)
Width: 489.0 mm (19.25 in.)
Depth: 132.7 mm (5.22 in)
2070 g (37.67 oz)
12 VDC
Description
80 watts
0°C to 40°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
+/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
Table 35 4-Slot Spare Battery Charger Technical Specifications
Item
Dimensions
Weight
Input Voltage
Power Consumption
Height: 104.4 mm (4.11 in.)
Width: 121.9 mm (4.80 in.)
Depth: 142.4 mm (5.61 in.)
619.3 g (21.85 oz)
12 VDC
30 watts
Description
204
Specifications
Table 35 4-Slot Spare Battery Charger Technical Specifications (Continued)
Item
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge (ESD) +/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
Description
0°C to 40°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
Table 36 16-Slot Spare Battery Charger Technical Specifications
Dimensions
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Item
Electrostatic Discharge (ESD)
Height: 104.9 mm (4.13 in.)
Width: 489.0 mm (19.25 in.)
Depth: 142.4 mm (5.61 in.)
2480 g (87.48 oz)
12 VDC
106 watts
Description
0°C to 40°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
+/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
205
Specifications
Table 37 USB Charge CableTechnical Specifications
Item
Dimensions
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge (ESD)
76.1 g (2.68 oz)
Description
Height: 55.8 mm (2.19 in.)
Width (with cable): 199.5 mm (7.85 in.)
Depth 52.8mm (2.07 in.)
5 VDC
12 watts
0°C to 50°C (32°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
75 cm (30 in.) to concrete; 2 drops/side for a total of 12 drops at room temperature (23°C).
+/- 15 kV air
+/- 8 kV contact
+/- 8 kV indirect discharge
206
www.zebra.com
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Advertisement
Android 10 Operating System
Multiple keypad options
Advanced barcode scanning capabilities
Rugged design for industrial environments
Wireless LAN (WLAN) and Bluetooth connectivity
NFC for easy pairing and information sharing
Refer to the 'Installing a microSD Card' section within the document for step-by-step instructions.
The serial number location is detailed in the 'Determining the Serial Number' section.
The 'Connecting to a Wi-Fi Network' section provides instructions on establishing a wireless connection.
See the instructions for 'Pairing the RS507/RS507X/RS6000 Hands-Free Imager' in the Data Capture section.
Follow the steps in the 'Performing an Enterprise Reset From Device Settings' section.
How can I adjust the volume of the good decode beep?
To be able to adjust the volume of the good decode beep, you must select the Decode-short option under Decode Audio Feedback within the DataWedge settings. If Optimized-beep is selected, the volume defaults to the highest level, and the physical volume slider will have no effect.
Login to continue
