advertisement
Register your product and get support at
www.philips.com/welcome
32PFL5605/98
40PFL5605/98
46PFL5605/98
32PFL5605S/98
40PFL5605S/98
46PFL5605S/98
EN
User manual
EN Addendum
You cannot play mp4 video fi les that use the H.264 or AVC codec.
FR Addenda
La lecture de fi chiers vidéo MP4 utilisant le codec H.264 ou AVC n’est pas prise en charge.
TH ภาคผนวก
คุณไม่สามารถเล่นไฟล์วิดีโอ MP4 ที่
เข้ารหัสแบบ H.264 หรือ AVC ได้
VI
Ph ụ l ụ c
B ạ n không th ể phát các t ậ p tin video MP4 s ử d ụ ng b ộ gi ả i mã
AVC ho ặ c H.264.
ZH-CN 附录
您无法播放使用 H.264 或
AVC 编解码器的 MP4 视频文
件。
您無法播放使用 H.264 或
AVC 編碼的 MP4 影像檔。
Contents
1 Notice
2 Important
2
3
Side controls and indicators
Remote control
5
5
5
Adjust TV volume
Use teletext
9
9
5 Use more of your TV
10
Access TV menus 10
Change picture and sound settings 10
Use advanced teletext features 13
Create and use lists of favourite channels 14
Use timers
Use child control
15
15
Use the TV clock 16
View photos, play music and watch video from a USB storage device 16
Use Scenea to display a picture as TV
Update the TV software
Change TV preferences
Start a TV demo
Reset the TV to factory settings
19
19
20
20
Automatically install channels
Manually install channels
Rename channels
Reorder channels
21
21
21
21
22
Back connectors
Bottom connectors
Side connectors
Connect a computer
Add devices
Use Philips EasyLink
Use a Kensington lock
Supported display resolutions
Remote control
Supported TV mounts
9 Troubleshooting
General TV issues
TV channel issues
Picture issues
Sound issues
HDMI connection issues
Computer connection issues
Contact us
10 Index
27
27
29
29
29
29
30
30
30
30
31
23
23
23
23
24
24
25
26
27
27
EN 1
1 Notice
2010 Koninklijke Philips Electronics N.V. All rights reserved.
- # notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly.
The material in this manual is believed adequate for the intended use of the system.
If the product, or its individual modules or procedures, are used for purposes other than
* " validity and suitability must be obtained. Philips warrants that the material itself does not infringe any United States patents. No further warranty is expressed or implied.
Philips cannot be held responsible either for any errors in the content of this document or for any problems as a result of the content in this document. Errors reported to Philips will be corrected and published on the Philips support website as soon as possible.
Pixel characteristics
This LCD product has a high number of colour pixels. Although it has effective pixels of
99.999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen. This is a structural property of the display (within common industry standards) and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove covers to the inside of the product. Repairs may only be done by Philips
; ! < to do so shall void any warranty, stated or implied.
Any operation expressly prohibited in this manual, any adjustments, or assembly procedures not recommended or authorised in this manual, shall void the warranty.
Compliance with EMF
Koninklijke Philips Electronics N.V. manufactures and sells many products targeted at consumers which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.
One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the Electro Magnetic Field (EMF) standards applicable at the time of producing the products.
Philips is committed to develop, produce and market products that cause no adverse health
! " handled properly for their intended use, they
# available today.
Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardisation for early integration in its products.
Copyright
$%&'* $%&' # $#+%
Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries.
Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world.
All other registered and unregistered trademarks are the property of their respective owners.
Portions of this software are copyright © The
FreeType Project (www.freetype.org).
2 EN
2 Important
Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply.
Safety
= Never expose the TV to rain or water.
Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact
Philips Consumer Care to have the TV checked before use.
= Never place the TV, remote control or
X >" sources, including direct sunlight.
* X
>" "
TV, remote control and batteries at all times.
= Never insert objects into the ventilation slots or other openings on the TV.
= When the TV is swivelled ensure that no strain is exerted on the power cord.
Strain on the power cord can loosen connections and cause arcing.
= Never expose the remote control or batteries to rain, water or excessive heat.
= Avoid force coming onto power plugs.
Loose power plugs can cause arcing or
!
Risk of injury or damage to the TV!
= Two people are required to lift and carry a TV that weighs more than 25 kg or 55 lbs.
= When stand mounting the TV, use only the supplied stand. Secure the stand to
#! >* surface that can support the combined weight of the TV and the stand.
= When wall mounting the TV, use only a wall mount that can support the weight of the TV. Secure the wall mount to a wall that can support the combined weight of the TV and wall mount. Koninklijke Philips
Electronics N.V. bears no responsibility for improper wall mounting that result in accident, injury or damage.
Risk of injury to children!
Follow these precautions to prevent the
TV from toppling over and causing injury to children:
= Never place the TV on a surface covered by a cloth or other material that can be pulled away.
= Ensure that no part of the TV hangs over the edge of the surface.
= Never place the TV on tall furniture (such as a bookcase) without anchoring both the furniture and TV to the wall or a suitable support.
= Educate children about the dangers of climbing on furniture to reach the TV.
Risk of swallowing batteries!
= The product/remote control may contain a coin-type battery, which can be swallowed. Keep the battery out of reach of children at all times!
Risk of overheating!
= Q !
Always leave a space of at least 4 inches or 10 cm around the TV for ventilation.
Ensure curtains or other objects never cover the ventilation slots on the TV.
Risk of damage to the TV!
= Before you connect the TV to the power outlet, ensure that the power voltage matches the value printed on the back of the TV. Never connect the TV to the power outlet if the voltage is different.
EN 3
= Never place the TV or any objects on the power cord.
= To easily disconnect the TV power cord from the power outlet, ensure that you have full access to the power cord at all times.
= When you disconnect the power cord, always pull the plug, never the cable.
= Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable.
Risk of hearing damage!
= Avoid using earphones or headphones at high volumes or for prolonged periods of time.
Low temperatures
= If the TV is transported in temperatures below 5°C or 41°F, unpack the TV and wait until the TV temperature matches room temperature before connecting the
TV to the power outlet.
Screen care
= Avoid stationary images as much as possible. Stationary images are images that remain on-screen for extended periods of time. Examples include: on-screen menus, black bars and time displays. If you must use stationary images, reduce screen contrast and brightness to avoid screen damage.
= Unplug the TV before cleaning.
= Clean the TV and frame with a soft, damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the TV.
= Risk of damage to the TV screen! Never touch, push, rub or strike the screen with any object.
= To avoid deformations and colour fading, wipe off water drops as soon as possible.
Disposal of your old product and batteries
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive
2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste.
Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste.
Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environment and human health.
4 EN
Congratulations on your purchase, and
" Z " support that Philips offers, register your TV at www.philips.com/welcome.
This section gives you an overview of commonly used TV controls and functions.
Side controls and indicators previous channel.
5 4 a
+/-: Increases or decreases volume.
1
2
3 b
: Selects connected devices.
c
P/CH +/-: Switches to the next or d
Power switch: Switches the TV on or off. e
Ambient sensor/ Standby indicator/
Remote control sensor
4
5
6
24
23
22
EN
10
11
12
13
14
15
16
17
18
19
20
21
8
9
25
7
27
26
1
2
3
29
28
5
Remote control
a
(Standby-On)
= Switches the TV to standby if it is on.
= Switches on the TV if it is in standby.
b
TELETEXT
Toggles teletext on or off.
c
SOURCE
Selects connected devices.
d
Colour buttons
Select tasks, options or teletext pages.
Available in selected models only. e
SLEEP
Sets a delay after which the TV switches to standby.
f
DUAL
Switches Stereo and Nicam Stereo to
&! ## [% '\ or second language (Dual II) in bilingual programmes.
g
(Home)
Toggles the home menu on or off.
h
OPTIONS
Accesses options relating to the current activity or selection.
i
OK
;" !% matrix of channels.
j
(Navigation buttons)
Navigate menus.
k
INFO
Displays programme information, if available.
l
(Backward)
Searches backward.
m
(Forward)
Searches forward.
n
(Play/Pause)
Starts, pauses or resumes disc play.
o
(Record)
Starts or stops video recording.
p
(Stop)
Stops disc play.
q
(Mute)
Mutes or restores volume.
r
CH +/- (Channel +/-)
Switches to the next or previous channel.
s
FORMAT
Selects a picture format.
t
0-9 (Numeric buttons)
Selects a channel or setting.
u
PICTURE (Smart picture)
Launches the smart picture menu.
v
SOUND (Smart Sound)
Launches the smart sound menu.
w
+/- (Volume +/-)
Increases or decreases volume.
x
BACK A/CH
Returns to a previous screen.
Toggles between the current channel and the last viewed channel.
y
BROWSE
Displays a matrix of channels.
z
SCENEA (Wallpaper)
Displays wallpaper on your TV screen.
{
DEMO
Toggles the demonstration menu on or off.
|
TV
Switches back to the antenna source from
EasyLink mode.
}
INCR. SURR
Enables Incredible Surround for stereo sources. Enables spatial mode for mono sources.
6 EN
Remote control usage
When using the remote control, hold it close to the TV and point it at the remote control sensor. Make sure that the line-of-sight between the remote control and TV is not blocked by furniture, walls or other objects.
~5m
~30˚
EN 7
EN
This section helps you perform basic TV operations (see ‘Use more of your TV’ on page
10).
Switch your TV on/off or to standby
To switch on
= If the standby indicator is off, press Power switch at the bottom of the TV.
= If the standby indicator is red, press
( Standby-On ) on the remote control.
To switch to standby
= Press ( Standby-On ) on the remote control.
»
The standby indicator switches to red.
To switch off
= Press the Power switch at the bottom of the TV.
»
The standby indicator switches off.
Tip
= Though your TV consumes very little power when in standby, energy continues to be consumed. When not in use for an extended period of time, disconnect the TV power cable from the power outlet.
Switch channels
= Press BACK A/CH on the remote control to return to the previously viewed channel.
= Press CH +/ on the remote control or
P/CH +/ on the side of the TV.
= Press OK to use the channel matrix.
= Enter a channel number using the
Numeric buttons .
Note
= When you use a favourite list, you can only select those channels in the list.
Watch connected devices
Use the source button
1
Press SOURCE .
»
The source list appears.
2
Press or to select the connected device.
3
Press to watch the connected device.
Use the home menu
Note
= You can add new devices to the home menu for easy access.
1
Press ( Home ).
»
The home menu appears.
2
Press to select the device.
3
Press to watch the connected device on your TV.
Adjust TV volume
To increase or decrease volume
= Press +/ on the remote control or at the side of the TV.
To mute or unmute sound
= Press to mute the sound.
= Press again to restore the sound.
Use teletext
1
Press TELETEXT.
»
The main index page appears.
2
Select a page as follows:
= Press the Numeric buttons to enter a page number.
= Press CH +/ or to view the next or previous page.
= Press the Colour buttons to select a colour coded item.
= Pressing BACK to return to the previously viewed page.
3
Press TELETEXT to exit teletext.
EN 9
10 EN
5 Use more of your TV
Access TV menus
Menus help you to install channels, change picture and sound settings and access other features.
Access the home menu
The home menu gives you easy access to connected devices, picture and sound settings, and other useful features.
1
Press ( Home ).
»
The menu screen appears.
Watch TV
2
Press
Add new device through one of the following menus.
Setup
to select and navigate
= [Watch TV] : Switches back to the aerial source if another source is selected.
= [Setup] : Accesses menus to change picture, sound and other settings.
= [Add new device] : Adds new devices to the home menu.
3
Press " !
4
Press ( Home ) to exit.
Tip
= After selecting [Add new device] , follow the on-screen instructions to select the correct device and connector.
Remove devices from the home menu
If a device is no longer connected to the TV, remove it from the home menu.
1
Press ( Home ).
2
Press to select a device to remove.
3
Press OPTIONS.
»
The [Remove device] list appears.
4
Press and select [Remove] to remove the device.
»
The selected device is removed from the home menu.
Change picture and sound settings
Change picture and sound settings to suit your
! ^ + # or change settings manually.
Use settings assistant
Use the settings assistant to guide you through the picture and sound settings.
1
Press ( Home ).
2
Press to select [Setup] >
[Picture] > [Settings assistant] .
3
Press .
»
The [Settings assistant] menu appears.
Follow the on-screen instructions to choose your preferred picture settings.
Use smart picture
| " + picture settings.
1
Press PICTURE .
»
The [Smart picture] menu appears.
2
Press to select one of the following smart picture settings.
= [Personal] : Lists customised picture settings.
= [Vivid] : Applies rich and dynamic settings.
= [Standard] : Adjusts picture settings to suit most environments and types of video.
= [Movie] : Applies settings for movie viewing.
= [Game] : Applies settings for games.
= [Energy saving] : Applies low-energy settings.
3
Press " !
»
The selected smart picture setting is applied.
Manually adjust picture settings
1
Press ( Home ).
2
Press to select [Setup] >
[Picture] .
»
The [Picture] menu appears.
3
Press to select from the following settings and adjust:
= [Smart picture] } ~ + smart picture settings.
= [Contrast] : Adjusts the intensity of bright areas, keeping dark areas unchanged.
= [Brightness] : Adjusts the intensity and details of dark areas.
= [Colour] : Adjusts colour saturation.
= [Hue] : Compensates for colour variations. (Available only during video playback.)
= [Sharpness] : Adjusts sharpness in the image.
= [Noise reduction] : Filters and reduces noise in an image.
= [Colour temp.] : Sets the colour tones to [Normal] , [Warm] (reddish) or [Cool]
(bluish).
= [Pixel Plus HD] : Fine-tunes each pixel to match surrounding pixels. This produces a
* #+ "#!
= [HD Natural Motion] : In selected
" ! `
>X "" smoothly. You can switch HDNM on or off.
= [100Hz Clear LCD] : Sets the
TV refresh rate to a maximum of
100Hz to provide superior motion sharpness, better black level, high
>X+* { image and a larger viewing angle.
= [Dynamic contrast] : Enhances contrast.
= [Dynamic backlight] : Adjusts brightness of the TV backlight to match lighting conditions.
= [Colour enhancement] : Makes colours more vivid and improves the details in bright colours. You can switch this feature on or off.
= [Backlight] : Adjusts the backlight.
= [PC mode] : Adjusts picture settings when a PC is connected to the TV.
= [Light sensor] : Adjusts settings dynamically to match lighting conditions.
= [Picture format] : Changes the picture format.
= [Horizontal shift] : Adjusts the picture horizontally for PC-VGA or HD input.
= [Vertical shift] : Adjusts the picture vertically for PC-VGA or HD input.
EN 11
Change picture format
1
Press FORMAT .
»
A picture format bar appears.
2
Press to select a picture format.
»
The selected picture format is activated.
3
Press " !
Summary of picture formats
The following picture settings can be
#!
Note
= Depending on the format of the picture source, some picture settings are not available.
[Super zoom] : (Not for HD and PC mode.)
Removes the black bars on the side of 4:3 broadcasts.
There is minimal distortion.
[4:3] : Shows the classic
4:3 format.
[Movie expand 16:9]
: (Not for HD and PC mode.) Scales 4:3 format to 16:9.
[Wide screen] : Scales 4:3 format to 16:9.
[Unscaled] : For HD and PC mode only, and in selected models only. Allows maximum sharpness. Some distortion may be present due to the broadcaster’s systems. Set your PC resolution to wide screen mode for best results.
Use smart sound
| " + settings.
1
Press SOUND .
»
The [Smart sound] menu appears.
2
Press to select one of the following smart sound settings.
= [Standard] : Adjusts sound settings to suit most environments and types of audio.
12 EN
= [News] : Applies settings for spoken audio, such as news.
= [Movie] : Applies settings for movies.
= [Personal] : Applies the settings that were customised in the sound menu.
3
Press " !
»
The selected smart sound setting is applied.
Manually adjust sound settings
1
Press ( Home ).
2
Press to select [Setup] > [Sound] .
»
The [Sound] menu appears.
3
Press to select and adjust:
= [Smart sound] : Accesses pre-
" #!
= [Bass] : Adjusts the bass level.
= [Treble] : Adjusts the treble level.
= [Volume] : Adjusts the volume.
= [Balance] : Adjusts the balance of the right and left speakers.
= [Dual I-II] : Selects audio languages if dual sound broadcast is available.
= [Mono/Stereo] : Selects mono or stereo if stereo broadcast is available.
= [TV speakers] : Sets the TV speakers on or off, or outputs sound to an
EasyLink-compliant device. This option is available when you select
[EasyLink] in the [Preferences] menu.
= [Surround] : Enables spatial sound.
= [Auto volume] : Automatically reduces sudden volume changes, for example, when switching channels.
= [Delta volume] : Corrects volume differences between TV channels and connected devices (switch to your connected device when adjusting [Delta volume] ).
Use advanced teletext features
Access the teletext options menu
Access the teletext features through the teletext options menu.
1
Press TELETEXT.
»
The teletext screen appears.
2
Press OPTIONS.
»
The teletext options menu appears.
3
Press to select one of the following options.
= [Freeze page] : Freezes the current page.
= [Dual/Full screen] : Enables and disables dual screen teletext.
= [Reveal] : Hides or reveals hidden information on a page, such as solutions to riddles or puzzles.
= [Cycle subpage] : Cycles through subpages automatically if subpages are available.
= [Language] : Switches to a different language group to display a language correctly when it uses a different character set.
4
Press " !
5
Press TELETEXT to exit the teletext options menu.
Select teletext subpages
A teletext page can hold several subpages.
Subpages are displayed on a bar next to the main page number.
1
Press TELETEXT.
»
The teletext screen appears.
2
Select a teletext page with subpages.
3
Press to enter a subpage.
»
The subpage appears.
4
Press to switch between subpages.
EN 13
Select T.O.P. teletext broadcasts
Table Of Pages (T.O.P.) teletext broadcasts allow you to jump from one subject to another without using page numbers. T.O.P. teletext is not broadcast on all TV channels.
1
Press TELETEXT.
»
The teletext screen appears.
2
Press INFO .
»
The T.O.P. overview appears.
3
Press to select a subject.
4
Press to view the page.
Create and use lists of favourite channels
You can create a list of your preferred TV easily.
Select the favourite list
1
When watching TV, press OK to display the channel grid.
2
Press OPTIONS.
»
The channel options menu appears.
3
Press to select [Show fav. ch.] .
4
Press to select the favourites list or
[All] .
5
Press .
»
If you select the favourites list, only the channels in the favourites list appear in the channel grid.
»
If you select [All] , all the installed channels appear in the channel grid.
6
Press BACK to exit the menu.
Add a channel to the favourite list
Tip
= View all channels before adding a channel to the favourite list.
1
When watching TV, switch to the channel you want to add to a favourite list.
2
Press to select a channel to add to the favourite list.
3
Press OPTIONS.
»
The channel options menu appears.
4
Press to select [Mark as favourite] .
5
Press .
»
The channel is added to the favourite list.
6
Press BACK to exit.
Tip
= When watching TV, press OPTIONS
> [Mark as favourite] to save the current channel in the favourite list.
Remove a channel from the favourite list
Note
= Select the favourite list to edit, before removing a channel (see ‘Select the favourite list’ on page 14).
1
When watching TV, press OK to display the channel grid.
2
Press OPTIONS.
»
The channel options menu appears.
3
Press to select [Unmark as fav.] .
4
Press .
»
The channel is removed from the favourite list.
5
Press BACK to exit.
14 EN
Use timers
You can set timers to switch the TV to standby
"!
Automatically switch the TV to standby (sleep timer)
Sleep timer switches the TV to standby after a
+ "!
Tip
= You can always switch off your TV earlier or reset the sleeptimer during the countdown.
1
Press ( Home ).
2
Press to select [Setup] >
[Features] > [Sleep timer] .
»
The [Sleep timer] menu appears.
3
Press to select a value between zero
"!
»
If set to zero minutes, the sleep timer is switched off.
4
Press to activate the sleep timer.
»
The TV switches to standby after the
"!
Automatically switch the TV on (on timer)
You can switch on the TV from standby to a
"!
1
Press ( Home ).
2
Press to select [Setup] >
[Features] > [On timer] .
3
Press to select [Activate] and set a frequency [Daily] , [Once] , or [Off] .
4
Press "!
5
Press to select [Time] and set the starting time.
6
Press "!
7
Press to select [Programme no.] and set the channel.
8
Press "!
9
Press BACK to exit.
Tip
= Select [On timer] > [Activate] > [Off] to disable [On timer] .
= When [On timer] is [Off] , only [Activate] can be selected.
= Set the TV clock before activating [On timer] feature.
Use child control
You can prevent your children from watching certain programs or certain channels by locking the TV controls.
Set or change your PIN code
1
Press ( Home ).
2
Press to select [Setup] >
[Features] > [Change/Set code] .
»
The [Change/Set code] menu appears.
3
Enter the code with the Numeric buttons .
»
~ "# "# your code is created or changed.
Tip
= ' # * override any existing codes.
Lock or unlock the TV
Lock the TV to prevent access to all channels and connected devices.
1
Press ( Home ).
2
Press to select [Setup] >
[Features] > [TV lock] .
»
A screen appears prompting you to enter a code.
3
Enter your code using Numeric buttons .
EN 15
4
Press to select [Lock] or [Unlock] .
5
Press .
»
All channels and connected devices are locked or unlocked.
Note
= If you select [Lock] , you have to enter your code every time you turn on your TV.
Display the TV clock
1
When watching TV, press OPTIONS.
»
The TV options menu appears.
2
Select .
3
Press .
»
The clock is displayed.
Note
= X " seconds.
= Set the TV clock again if you have switched off/on your TV using the power switch.
Lock or unlock one or more channels
1
When watching TV, press OK to display the channel grid.
2
Press to select a channel to lock or unlock.
3
Press OPTIONS.
4
Press to select [Lock channel] or
[Unlock channel] .
5
For each selection, press OK to lock or unlock the channel.
Note
= Restart the TV for the change to take effect.
Use the TV clock
You can display a clock on the TV screen.
Set the TV clock
1
Press ( Home ).
2
Press to select [Setup]
3
Select > [Clock] and press
OK .
»
The [Clock] setup appears.
4
Enter the time with the Numeric buttons .
5
Select , then press OK .
»
The time has been set.
6
To return to watching TV, press twice.
16 EN
View photos, play music and watch video from a USB storage device
Caution
= Philips is not responsible if the USB storage device is not supported, nor is it responsible for damage or loss of data from the device.
Your TV has a USB connector that enables you to view photos, listen to music or watch movies stored on a USB storage device.
Playback type
Pictures JPEG (non-progressive only)
Music
Video
MP3
MP4, RM
Note
= Only FAT or DOS-formatted USB storage devices are supported. File names must not
!
Browse the USB storage device
1
Turn on the TV.
2
Connect the USB storage device to the
TV.
3
Press ( Home ).
»
The home menu appears.
4
Press to select [Browse USB] .
5
Press "!
»
The USB content browser appears.
Tip
= Press BROWSE to switch between
" # !
Disconnect a USB storage device
Caution
= Follow this procedure to avoid damage to your
USB storage device.
1
Press ( Home ) to exit the [USB] menu.
2 disconnecting the USB storage device.
View photos
1
In the USB content browser, select
[Picture] and press to enter.
2
Press BROWSE to switch between
" # !
3
Press to select a photo.
4
Press to view the selected photo in full screen mode.
Tip
= When in full screen mode, press to move between photos.
View a slide show of your photos
1
When a full screen image of a photo is displayed, press OK or .
»
A slide show begins from the selected image.
2
Press:
= OK or to pause the slide show.
»
The icon appears.
= Press or to move between images.
= Press BACK or to stop the slide show.
Change slide show settings
1
When viewing a slide show, press
OPTIONS.
»
The slide show options menu appears.
2
Press to select one of the following.
= [Start/Stop slide.] : Starts or stops a slide show.
= [Slideshow trans.] : Sets the transition from one picture to the next.
= [Slideshow freq.] : Sets the amount of time that a picture is shown.
= [Rotate image] : Rotates a picture.
= [Set as wallpaper] : Sets the image as wallpaper.
= [Show info] : Displays the picture name, date and size of the picture in the slide show.
3
Press " #!
Note
= [Rotate image] and [Show info] appear only when you press OK or to pause the slide show.
Listen to music
1
Connect a USB storage device to the TV.
2
Press to enter the menu.
3
Select , and then press to enter the [Music] folder.
EN 17
4
Press or to select a song.
5
Press or to play the song.
= Press OK or to pause, press OK or again to resume.
= Press to search-forward.
= Press to search-backward.
= Press to stop playback.
View a slideshow with music
You can view a picture slide show with background music.
1
While the TV is on, connect the USB storage device containing your pictures and the music to the TV.
2
Press ( Home ).
3
Press to select [Browse USB] >
[Music] .
4
Press to select an album of songs and press OK .
5
Press BACK to return to the USB content browser.
6
Press to select [Picture] .
7
Press to select an album of pictures and press OK .
Watch video from a USB device
1
In the USB content browser, press to enter the [Video] folder.
2
Press to select a video.
3
Press or to play the video.
= Press OK or to pause, press OK or again to resume.
= Press to search-forward.
= Press to search-backward.
= Press to stop playback.
Use Scenea to display a picture as TV wallpaper
You can use Scenea to display a picture as wallpaper on your TV. Make sure that the location of your TV is set to home (see ‘Change
TV preferences’ on page 19).
Activate Scenea
Single-picture wallpaper
Press SCENEA on your remote control.
»
The default or pre-loaded picture is displayed.
Note
= To deactivate the wallpaper, press any remote control button except , SMART SOUND , or SMART PIC .
= The wallpaper is also deactivated when you connect a USB storage device to the TV or start an EasyLink-compliant device through one-touch play.
Wallpaper slide show
Make sure the wallpaper is not yet activated.
1
Connect a USB storage device to the TV.
2
Press .
»
All pictures in the USB storage device are displayed.
Note
= If the sleep timer is off, the wallpaper is displayed for 120 minutes. Otherwise, it is displayed for the duration of the sleep timer.
Upload a wallpaper picture from a
USB device
Make sure your USB storage device contains a picture of less than 1MB.
1
While the TV is on, connect the USB storage device containing your pictures to the USB connector at the side of your TV.
EN
2
Press ( Home ).
»
The home menu appears.
3
Press to select [Browse USB] .
4
Press to navigate to the picture of your choice.
5
Press .
»
Your picture is stored as the default
Scenea picture in your TV.
6
Disconnect the USB storage device.
Adjust wallpaper settings
1
Press ( Home ).
2
Select > [Features] > [Scenea] .
3
Press to select from the following settings:
= [Activate] : Enters the Scenea mode.
= [ECO] : Applies low-energy settings.
Select [On] to display wallpaper with lower brightness.
Note
= Select the [ECO] setting before you select
[Activate] to display Scenea wallpaper.
Update the TV software
Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available.
Check www.philips.com/support for availability.
Check the current software version
1
Press ( Home ).
2
Select > [Software update] >
[Current software] .
Download the software
1
On your PC, open a web browser and go to www.philips.com/support.
2
Download the latest software upgrade
;!
3
%" '+!
4
; !# directory of the USB device.
Update software (analogue broadcasts)
Before you perform this procedure, make sure you have:
= Enough time to complete the entire update.
= A USB storage device with at least 64MB of storage space.
= Access to a computer with a USB port and internet access.
1
Switch on the TV set.
2
Connect the USB storage device to the
TV.
3
Press to select [Setup] >
[Software update] > [Local update] .
4
Press .
5
Follow the on-screen instructions to complete the software update.
Change TV preferences
The [Preferences] menu allows you to customise various features and functions.
1
Press ( Home ).
2
Select > [Installation] >
[Preferences] .
= [Location] : Optimises TV settings for your location - home or shop.
= [Volume bar] : Displays the volume bar when you adjust the volume.
= [EasyLink] : Enables one-touch play and one-touch standby between
EasyLink-compliant devices.
= [Pixel Plus Link] : Overrides the settings of connected devices and uses the settings of the TV.
= [E-sticker] : For shop mode only.
Sets the location of the e-sticker.
EN 19
Start a TV demo
You can use demonstrations to better understand the features of your TV. Some demos are not available on certain models.
Available demos are displayed in the menu list.
1
Press on the remote control.
2
Press to select a demo and press OK to view it.
3
Press to exit.
Reset the TV to factory settings
You can restore the default picture and sound settings of your TV. The channel installation settings remain the same.
1
Press ( Home ).
2
Select > [Installation] > [Factory settings] .
3
Press or to enter the [Factory settings] menu.
»
[Reset] is highlighted.
4
Press to reset to factory settings.
5
Press ( Home ) to exit.
20 EN
Automatically install channels
This section describes how to search and store channels automatically.
1
Press ( Home ).
2
Select > [Channel install.]
> [Channel assistant] .
3
Press .
4
Follow the on-screen instructions to install channels.
Manually install channels
This section describes how to search and store analogue TV channels manually.
Step 1 Select the colour and sound system
1
Press ( Home ).
2
Press to select [Setup] >
[Installation] > [Channel install.] >
[Analogue: Manual] .
»
The [Analogue: Manual] menu appears.
3
Press to select and enter [Colour system] .
»
A list of available colour systems appears.
4
Press to select your colour system and then press OK .
5
Press to return to the [Analogue:
Manual] menu.
6
Press to select and enter [Sound system] .
»
A list of available sound systems appears.
7
Press to select your sound system and then press OK .
Step 2 Search and store new TV channels
1
Press ( Home ).
2
Press to select [Setup] >
[Installation] > [Channel install.] >
[Analogue: Manual] .
»
The [Analogue: Manual] menu appears.
3
Press to select and enter
[Search] .
4
Press to manually enter the three-digit frequency.
5
Press to begin search.
»
If a channel is unavailable at the selected frequency, the system searches for the next available channel.
6
Press BACK when the new channel is found.
7
Press to select [Store new channel] to store the new channel under a new channel number.
8
Press to enter [Store new channel] .
9
Press to store the new channel.
10
Press ( Home ) to exit.
Rename channels
You can rename channels. The name appears when you select the channel.
1
When watching TV, press OK to display the channel grid .
2
Select the channel you want to rename.
3
Press OPTIONS.
»
The channel options menu appears.
4
Press to select and enter
[Rename chan.] .
»
A text input box appears.
5
Press to select characters.
6
Press " characters.
EN 21
Tip
= Rename channels - a channel name can be up to six characters long.
= Press [Aa] to change an uppercase letter to a lowercase letter and vice versa.
Reorder channels
After you install channels, you can rearrange the order in which they appear.
1
When watching TV, press BROWSE repeatedly until the channel grid is displayed.
2
Press OPTIONS.
»
The channel options menu appears.
3
Press to select and enter
[Reorder] .
4
Select the channel you want to reorder and press OK .
»
The selected channel is highlighted by a yellow border.
5
Press to select the new position for the channel.
»
The new position is highlighted by a blue border.
6
Press " !
7
Press OPTIONS.
»
[Done reordering] appears.
8
Press #!
22 EN
This section describes how to connect various devices with different connectors and supplements examples provided in the Quick
Start.
Note
= Different types of connectors may be used to connect a device to your TV, depending on availability and your needs. A comprehensive interactive guide to help you connect your product is available at www.connectivityguide.
philips.com.
Back connectors a
CVI 2 (Y Pb Pr and AUDIO L/R)
Analogue audio and video input from analogue or digital devices such as DVD players or game consoles.
b
SERV. U
For use by service personnel only.
c
AV IN (S-VIDEO, VIDEO, and AUDIO
L/R)
Video input for analogue devices such as DVD, camcorder, game console etc. To be used with audio input.
Bottom connectors a
CVI 1 (Y Pb Pr and AUDIO L/R)
Analogue audio and video input from analogue or digital devices such as DVD players or game consoles.
b
DIGITAL AUDIO OUT
Digital audio output to home theatres and other digital audio systems.
c
ANTENNA
Signal input from an antenna, cable or satellite.
d
VGA and AUDIO IN
Audio and video input from a computer.
e
HDMI
Digital audio and video input from high-
# + !
Side connectors a
USB
Data input from USB storage devices.
b
HDMI
Digital audio and video input from high-
# + players.
EN 23
24 EN
Connect a computer
= Before you connect a computer to the
TV, set the monitor refresh rate on your computer to 60Hz.
= Connect your computer to the TV.
= Press FORMAT and change the TV picture format to [Unscaled] .
Connect a computer with one of the following connectors:
Note
= Connections via DVI or VGA require an additional audio cable.
= HDMI cable
= DVI-HDMI cable
AUDIO IN
DVI/VGA
= HDMI cable and HDMI-DVI adaptor
DVI
AUDIO IN
DVI/VGA
= VGA cable
AUDIO IN
DVI/VGA
Add devices
After connecting devices, assign the device attached to each connector. This allows you to easily identify devices connected to your TV.
1
Press ( Home ).
2
Select and press OK .
3
Select and press OK .
4
Press or to select a device and press
.
5
Press or to select the connector your device is connected to and press .
6
If available, press or to select the audio connector your device is connected to and press .
7
Switch on your device and check for video and audio output.
VGA
DVI
8
If there is video and audio output, press
OK .
Repeat the procedure until all devices are correctly assigned to connectors.
Use Philips EasyLink
Your TV supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices that are connected through HDMI connectors can be controlled by a single remote control.
Note
= Philips does not guarantee 100% interoperability with all HDMI CEC devices.
Note
= The EasyLink-compliant device must be switched on and selected as the source.
EasyLink features
One-touch play
When you connect your product to devices that support one-touch play, you can control your product and the devices with one remote control. For example, when you press
Play on your DVD remote control, your TV automatically switches to the correct channel to show the DVD content.
One-touch standby
When you connect your TV to devices that support standby, you can use your TV remote control to put your TV and all connected
HDMI devices in standby mode.
System audio control
When you connect your TV to HDMI
CEC compliant devices, your TV can switch automatically to play audio from the connected device.
To use one-touch audio, you must map the audio input from the connected device to your TV.
You can use the remote control from the connected device to adjust the volume.
Remote control (RC) key forwarding
RC key forwarding allows you to control
EasyLink-compliant devices using your TV remote control.
EasyLink buttons
You can control EasyLink-compliant devices with the following buttons on the remote control of your TV.
(
Button
( Play/
Pause )
EasyLink function
Starts, pauses or resumes playback on your EasyLink device.
( Stop ) Stops playback on your EasyLink device.
( Record )
Starts or stops video recording on your EasyLink device.
( Fast
Backward )
Searches backward.
Searches forward.
( Fast
Forward )
0-9
( Numeric buttons )
When EasyLink is enabled, selects a title, chapter or track.
OK
OPTIONS
Standby-
On )
Navigates through the menus of the EasyLink-compliant device.
Activates a selection or accesses the menu of the EasyLinkcompliant device.
Displays the menus of the
EasyLink-compliant device. Press
( Home ) to display the TV menu.
When EasyLink is enabled, switches the TV and all EasyLink devices to standby. Press and hold ( Standby-On ) for at least
3 seconds.
EN 25
26 EN
Tip
= Press TV to switch back to the aerial source from EasyLink mode.
Enable or disable EasyLink
Note
= Do not enable Philips EasyLink if you do not intend to use it.
1
Press ( Home ).
2
Select > [Preferences] >
[EasyLink] .
3
Select or [OFF] .
Enable or disable remote control key forwarding
1
Press OPTIONS.
2
Select .
3
Press .
4
Press or to highlight an HDMI connector.
5
Press to enable RC key forwarding for the selected HDMI connector.
Set TV speakers to EasyLink mode
When you play content from an EasyLink compliant home theater, the TV speakers are automatically muted.
1
Press ( Home ).
2
Press to select [Setup] > [Sound] .
»
The [Sound] menu appears.
3
Select .
»
The [TV speakers] menu appears.
4
Select .
»
TV speakers are set to EasyLink mode.
Use a Kensington lock
There is a Kensington security slot at the bottom of the TV. Prevent theft by looping a Kensington lock between the slot and a permanent object, such as a heavy table.
8 Product information
Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
Supported display resolutions
Computer formats (HDMI/VGA)
Resolution
Refresh rate (Hz)
60
60
60
60
60
60
Video formats (HDMI/YPbPr)
Resolution
720 x 576i
720 x 576p
Refresh rate (Hz)
60
50
60
50
50, 60
50, 60
24, 25, 30, 50, 60
Tuner/Reception/
Transmission
= Antenna input: 75ohm coaxial (IEC75)
= TV system: PAL
= Video playback: NTSC, PAL
Multimedia
= Connection: USB
= Playback formats: MP4, JPEG, JPG, MP3
Video playback via USB:
Container Video codec
Mpeg1 Mpeg-1
Audio codec
Mpeg audio
Mpeg4 Mpeg-4 AAC
RealMedia Real
Media
AAC,
Cook
File extension
.dat
.mpg
.avi
.mp4
.rm
.rmvb
Remote control
= Batteries: 2 x AAA (R03 type)
Power
= Mains power: AC 220-240 (50-60Hz)
= Standby power: < 0.15W
= Ambient temperature: 5 to 40 degrees
Celsius
Supported TV mounts
To mount the TV, purchase a Philips TV mount.
To prevent damage to cables and connectors, be sure to leave a clearance of at least 2.2 inches or 5.5cm from the back of the TV.
Warning
= Follow all instructions provided with the TV mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper TV mounting that results in accident, injury or damage.
EN 27
TV screen size
Wall bracket type
32” - 40” 200 x 200 mm
46” - 52” 300 x 300 mm
Screw size
M6
&
%# - # without notice.
32PFL5605
= Without TV stand
= Dimension (WxHxD): 790 x 501 x
92 (mm)
= Weight: 10 kg
= With TV stand
= Dimension (WxHxD): 790 x 542 x
221 (mm)
= Weight: 11.5 kg
40PFL5605
= Without TV stand
= Dimension (WxHxD): 977 x 605 x
[""\
= Weight: 13.7 kg
= With TV stand
= Dimension (WxHxD): 977 x 649x
236 (mm)
= Weight: 16.1 kg
46PFL5605
= Without TV stand
= %" [$%\}
[""\
= Weight: 17.9 kg
= With TV stand
= Dimension (WxHxD): 1122 x 731 x
[""\
= Weight: 21.3 kg
Note
= %# - # without notice.
EN
9 Troubleshooting
This section describes commonly encountered issues and accompanying solutions.
General TV issues
The TV does not switch on:
Disconnect the power cable from the power outlet. Wait for one minute then reconnect it.
Check that the power cable is securely connected.
The remote control is not working properly:
Check that the remote control batteries are correctly inserted according to the
+/- orientation.
Replace the remote control batteries if
> X!
Clean the remote control and TV sensor lens.
The standby light on the TV blinks red:
Disconnect the power cable from the power outlet. Wait until the TV cools down before reconnecting the power cable. If the blinking reoccurs, contact
Philips Consumer Care.
You forgot the code to unlock the child lock feature
!
The TV menu is in the wrong language.
Change the TV menu to your preferred language.
When turning the TV on/off/to standby, you hear a creaking sound from the TV chassis:
No action is required. The creaking sound is normal expansion and contraction of the TV as it cools down and warms up.
This does not impact performance.
TV channel issues
Previously installed channels do not appear in the channel list:
Check that the correct channel list is selected.
Picture issues
The TV is on, but there is no picture:
Check that the antenna is properly connected to the TV.
Check that the correct device is selected as the TV source.
There is sound but no picture:
Check that the picture settings are correctly set.
There is poor TV reception from an antenna connection:
Check that the antenna is properly connected to the TV.
Loudspeakers, unearthed audio devices, neon lights, high buildings and other large
- > {!
If possible, try to improve the reception quality by changing the antenna direction or moving devices away from the TV.
If reception on only one channel is poor,
!
There is poor picture quality from connected devices:
Check that the devices are connected properly.
Check that the picture settings are correctly set.
The TV did not save your picture settings:
= Check that the TV location is set to the home setting. This mode offers you the
> # #!
" big or too small:
Try using a different picture format.
The picture position is incorrect:
Picture signals from some devices may
! ;X signal output of the device.
EN 29
Sound issues
There is a picture but sound quality is poor:
Note
= If no audio signal is detected, the TV automatically switches the audio output off
— this does not indicate malfunction.
Check that all cables are properly connected.
Check that the volume is not set to 0.
Check that the sound is not muted.
There is a picture but the sound quality is poor:
Check that the sound settings are correctly set.
There is a picture but sound comes from one speaker only:
Verify that sound balance is set to the centre.
HDMI connection issues
There are problems with HDMI devices:
Note that HDCP (High-bandwidth Digital
Content Protection) support can delay the time taken for a TV to display content from a HDMI device.
If the TV does not recognize the HDMI device and no picture is displayed, try switching the source from one device to another and back again.
If there are intermittent sound disruptions, check that output settings from the HDMI device are correct.
If you use an HDMI-to-DVI adapter or HDMI to DVI cable, check that an additional audio cable is connected to
AUDIO L/R or AUDIO IN (mini-jack only).
Computer connection issues
The computer display on the TV is not stable:
Check that your PC uses the supported resolution and refresh rate.
Set the TV picture format to unscaled.
Contact us
If you cannot resolve your problem, refer to the FAQs for this TV at www.philips.com/ support.
If the problem remains unresolved, contact
Philips Consumer Care in your country as listed in this user manual.
Warning
= Do not attempt to repair the TV yourself. This may cause severe injury, irreparable damage to your TV or void your warranty.
Note
= Make a note of your TV model and serial number before you contact Philips. These numbers are printed on the back of the TV and on the packaging.
30 EN
10 Index
A antenna 23
B back connectors 23 batteries 27, 4, 29 bracket for wall mount 27
C care channels install automatic 21 manual 21 lock 16 rename 21 reorder/rearrange 22 troubleshooting 29 tune 21 child lock lock channels lock connected devices
16
15
PIN code computer
29, 15 connect 30 display resolution 27 connect antenna 23
PC 30
23 power cord connectors back connectors 23
4 overview 23 side connectors 23
USB 16 controls 5
D default settings 20 demo 20 devices 23 devices add to home menu 10, 24 remove 10 digital services disconnect USB 17 display resolution 27 dispose 4
E
EasyLink disable 26 enable 26 system audio control 26 end of life environmental care e-sticker 19
4
4
F factory settings 20
H
HDMI 30, 23, 23 home mode 19
I install channels automatic 21 manual 21
K
Kensington lock 26
L language menu 29 troubleshoot 29 location
EN 31
home or shop lock
Kensington lock lock channels lock connected devices
PIN code
19
26
16
15
29, 15 overview 5
RC pass-through 26
troubleshooting 29 rename channels 21 reorder channels 22 resolution 27 restore default 20
M menu language 29 main menu 10, 10 teletext 13 troubleshooting 29
MHEG teletext 9
MPEG artifact reduction 11 multimedia 27 music
USB 17
S safety screen care screen saver settings
3
4 settings assistant 10 shop mode 19 mute TV speakers 26 side connectors 23 side controls 5 slideshow
O on timer 15 view 17
" smart picture 11
P smart settings 11,
PC smart sound 12 connect 30 software resolution 27 update 19 picture format change 12
27 version 19 sound settings 12, troubleshooting 29 picture settings 10
PIN code pixel plus link
15
19 standby switch
27 subpages in teletext
*
13 power preferences
27, 29, 5
19
R rearrange channels 22 reception 29 recycle 4 register product remote control
5
T
Table of Pages 14
27 teletext features 13 menu 13 subpages 13
32 EN
Contact information
België/ Belgique
0800 80 190 Gratis / Gratuit
ß CHAT www.philips.com/support
#$%&'*;<
00800 11 544 24
= > ?
800142840 Bezplatný hovor
@
3525 8759 Lokalt opkald
ß CHAT www.philips.com/support
@
0800 000 7520 gebührenfreier Anruf
ß CHAT www.philips.com/support
JQQZ\^
0 0800 3122 1280
_`
900 800 655 Teléfono local gratuito solamente para clientes en España
ß CHAT www.philips.com/support
_
6008600 kohalik kõne tariifi
{
0805 025 510 numéro sans frais
ß CHAT www.philips.com/support
|}
0800 222778 free
~
01 601 1777
~
800 088774 Numero Verde
'''
+7 727 250 66 17 local
}
52737691 local
67228896 local
? ?
40 6661 5644
Ortsgespräch/Appel local
>
0680018189 Ingyenes hívás
0800 0230076 Gratis nummer
22 70 81 11 Lokalsamtale
0800 180 016
00800-311-13-18
Pozosta?e produkty RTV oraz AGD
800780903 Chamada Grátis
;<
(495) 961-1111
8-800-200-0880
[ ¡¢£¤¥¦§¨ª «¬§® £ ¯¢¢±±\
0800-894910 Apel gratuit
0318107125 Apel local
*;'
+381 114 440 841 Lokalni poziv
}
0800 004537 Bezplatný hovor
}
00386 12 80 95 00 lokalni klic
}
08 5792 9100 Lokalsamtal
}
0800 002 050
Schweizer Festnetztarif/ Tarif réseau fixe France
09 2311 3415 paikallispuhelu
²³ "
General No: 0800 331 6015 free
General National Rate No:
0870 911 0036 National rate
*''
0-800-500-697
This information is correct at the time of print! For updated information, see www.philips.com/support.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: 3139 125 41581
advertisement
Key Features
- 81.3 cm (32")
- Full HD 1920 x 1080 pixels 16:9
- 450 cd/m² 2 ms
- DVB, DVB-C, DVB-T PAL BG, PAL DK, PAL I, SECAM B/G, SECAM D/K, SECAM L
- 71 W
Related manuals
advertisement