advertisement
COMPACT COMPONENT SYSTEM
FS-H300
–Consists of CA-FSH300 and SP-FSH300
FS-H300[J]cover5.p65
1
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No.
Serial No.
LVT1193-001A
[J]
04.3.17, 11:46 AM
Warnings, Cautions and Others
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION— (STANDBY/ON) button!
Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The (STANDBY/ON) button in any position does not disconnect the mains line.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION—Touche (STANDBY/ON)
Déconnectez la fiche secteur pour mettre l’appareil complètement hors tension (tous les témoins et toutes les indications s’éteignent). La touche (STANDBY/ON) dans n’importe quelle position ne déconnecte pas l’appareil du secteur.
• Quand l’appareil est en mode d’attente, le témoin STANDBY est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.
L’alimentation ne peut pas être commandée à distance.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.
Do not remove screws, covers or cabinet.
2.
Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1.
Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2.
Ne pas exposer l’appareil à la pluie ni à l’humidité.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
G-1
FS-H300[J]safety5.p65
1 04.3.17, 11:42 AM
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS
ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQUAU FOND.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE
CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFER-
ENCE-CAUSING EQUIPMENT STANDARD ENTITLED
“DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT
OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES
DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR:
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
1 CLASS 1 LASER PRODUCT
2 CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.
3 CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
4 REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE UNIT.
1 PRODUIT LASER CLASSE 1
2 ATTENTION: N’ouvrez pas le couvercle supérieur. Il n’y a aucune pièce réparable par l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.
3 ATTENTION: Risque de radiations laser visible et invisible quand l’appareil est ouvert et que le système de verrouillage ne fonctionne pas ou a été mis hors service. Évitez toute exposition directe au rayon.
4 REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE
DE PRÉCAUTION PLACÉE À L’INTERIEUR DE
L’APPAREIL.
CAUTION -
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT !
UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEI.
GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT
IST. NICHT DEM STRAHL AUSSETZEN!
VARNING -
OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.
ADVARSEL -
USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Front view Side view
1 cm
15 cm
1 cm
15 cm 15 cm 15 cm
SP-FSH300 CA-FSH300 SP-FSH300
10 cm
15 cm
CA-FSH300
G-2
FS-H300[J]safety5.p65
2 04.3.17, 11:42 AM
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.
About This Manual
This manual is organized as follows:
• This manual mainly explains operations using the buttons on the remote control.
You can use the buttons both on the remote control and on the unit for the same operations if they have the same or similar names (or marks), unless mentioned otherwise.
• Basic and common information that is the same for many functions is grouped in one place, and is not repeated for each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Common Operations” on pages 8 and 9.
• The following symbols are used in this manual:
Gives you warning and caution to prevent damage or risk of fire/electric shock.
In addition, we put information here about conditions which will prevent getting the best possible performance from the unit.
Gives you information and hints you need to know.
Power sources
• When unplugging the unit from the wall outlet, always pull on the plug, not the AC power cord.
DO NOT handle the AC power cord with wet hands.
Moisture condensation
Moisture may condense on the lenses inside the unit in the following cases:
• After starting to heat the room.
• In a damp room.
• If the unit is brought directly from a cold to a warm place.
Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, then plug it in again.
Others
• Should any metallic object or liquid fall into the unit, unplug the AC power cord and consult your dealer before operating any further.
• If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet.
• Rating label is placed on the exterior of the bottom.
DO NOT disassemble the unit since there are no user serviceable parts inside.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor too cold—between 5˚C (41˚F) and 35˚C (95˚F).
• Install the unit in a location with adequate ventilation to prevent internal heat buildup.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference with TV.
DO NOT install the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.
If anything goes wrong, unplug the AC power cord and consult your dealer.
1
01-05_FS-H300[J]6.p65
1 04.3.17, 11:42 AM
Contents
Location of the Buttons and Controls ............................. 3
Main Unit .................................................................................. 3
Remote Control ......................................................................... 5
Getting Started .................................................................. 6
Unpacking ................................................................................. 6
Connecting AM and FM Antennas ............................................ 6
Connecting Speakers ................................................................. 6
Connecting Other Equipment .................................................... 7
Putting the Batteries into the Remote Control .......................... 7
Common Operations ......................................................... 8
Setting the Clock ....................................................................... 8
Turning On the Power ............................................................... 8
Turning Off the Unit Automatically (Auto Standby) ................ 8
Selecting the Source .................................................................. 9
Adjusting the Volume ................................................................ 9
Fade-Out Muting (FADE MUTING) ........................................ 9
Selecting the Sound Modes ....................................................... 9
Reinforcing the Bass Sound ...................................................... 9
Checking the Clock Time During Play ..................................... 9
Playing Back Discs .......................................................... 10
Playing Back the Entire Disc—Normal Play .......................... 10
Basic Disc Operations ............................................................. 11
Programming the Track Playing Order—Program Play .......... 11
Repeating Tracks—Repeat Play .............................................. 12
Playing at Random—Random Play ......................................... 13
Displaying the Remaining Time during Playback ................... 13
Playing Back Tapes .......................................................... 14
Playing Back a Tape ................................................................ 14
Listening to FM and AM Broadcasts ............................. 15
Tuning in to a Station .............................................................. 15
Presetting Stations ................................................................... 15
Tuning in to a Preset Station ................................................... 16
Using an External Equipment ........................................ 16
Listening to the External Equipment ....................................... 16
Recording ......................................................................... 17
Recording on a Tape ................................................................ 17
Recording Discs—Disc Synchronized Recording .................. 18
Using the Timers .............................................................. 19
Using Daily Timer and Recording Timer ................................ 19
Using Snooze Timer ................................................................ 20
Using Sleep Timer ................................................................... 21
Maintenance ..................................................................... 22
Troubleshooting ............................................................... 23
Specifications ................................................................... 24
01-05_FS-H300[J]6.p65
2 04.3.17, 11:42 AM
2
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Main Unit
Top view
1
COMPACT
DIGITAL AUDIO
OPEN
2
D A I L Y T I M E R / S N O O Z E
3
Front view
4
5
6
7
8
9 p
COMPACT
DIGITAL AUDIO
STANDBY
CD
#
/
8
TAPE FM/AM AUX
–
PHONES DOWN
4 7
UP
¢ REC
VOLUME
AUX
+
A U T O R E V E R S E
PUSH OPEN
F S – H 3 0 0
C O M PAC T C O M P O N E N T S Y S T E M q w e r t
3
01-05_FS-H300[J]6.p65
3 04.3.17, 11:42 AM
Continued
Display window
1 2 3 4 5 6 7 8 9 p q w e
REC SLEEP SNOOZE MONO ST MP3 SOUND BASS REC
ON OFF
DAILY 123
ALL GR.
PRGM RANDOM TOTAL REMAIN
MHz kHz
A.STANDBY
r t y u i o ; a
See pages in parentheses for details.
Main unit
1 Disc cover (10)
2 ) OPEN (disc cover open) (10)
3 DAILY TIMER/SNOOZE button (20)
4 Remote sensor (5)
5 STANDBY lamp (8)
6 (STANDBY/ON) button (8)
7 Source buttons
• CD
#¥8
, TAPE
¤‹
, FM/AM, AUX
Pressing one of these buttons also turns on the unit.
8 PHONES jack (9)
9 Multi control buttons
• DOWN
4
,
7
, UP
¢ p Cassette holder (14, 17, 18) q Display window w VOLUME + / – control (9) e AUX jack (7, 17) r REC button (17, 18) t PUSH OPEN button (14, 17)
Display window
1 DAILY 1/2/3 (timer number) indicator
2 (timer) indicator
3 ON/OFF (timer on-time/off-time) indicators
4 REC (recording timer) indicator
5 (group folder) indicator
6 SLEEP indicator
7 SNOOZE indicator
8 FM mode indicators
• MONO , ST (stereo)
9 MP3 indicator p SOUND indicator q BASS indicator w REC (recording) indicator e 2 3 (tape direction) indicator r Repeat indicators
• , ALL, GR. ( group ) t (reverse mode) indicator y PRGM (program) indicator u RANDOM indicator i Main display o Remain indicators
• TOTAL , REMAIN
; A.STANDBY
indicator a Frequency indicators
• MHz , kHz
01-05_FS-H300[J]6.p65
4 04.3.17, 11:42 AM
4
Remote Control
See pages in parentheses for details.
1
2
3
4
5
6
7
8
9 p q
STANDBY/ON DISPLAY FM MODE A. STANDBY
SLEEP
1 2 3
CLOCK
/TIMER
4 5 6
SET
7 8
CANCEL
0
CD
3 / 8
TAPE
RANDOM PROGRAM
FM/AM
REPEAT
9
OVER
AUX
REMAIN
UP
PRESET
GROUP
VOLUME
DOWN
PRESET
GROUP
SOUND/HBS BEAT CUT REV.MODE FADE MUTING
RM - SFS H300J REMOTE CONTROL w e r u i o t y
1 STANDBY/ON button (8, 20)
2 SLEEP button (21)
3 CLOCK/TIMER button (8, 19)
4 SET button (8, 15, 19, 20)
5 CANCEL button (19, 20)
6 Source buttons
• CD
3¥8
, TAPE
2 3
, FM/AM, AUX
Pressing one of these buttons also turns on the unit.
7 RANDOM button (13)
8 PROGRAM button (11, 12)
9 Multi control buttons
• PRESET GROUP /UP, PRESET GROUP /DOWN
•
4
,
7
,
¢ p SOUND/HBS button (9) q BEAT CUT button (17) w DISPLAY button (9) e A. (auto) STANDBY button (8) r FM MODE button (15) t Number buttons (11, 15, 16) y OVER button (11, 15, 16) u REMAIN button (13) i REPEAT button (12) o VOLUME + / – buttons (9, 20)
; FADE MUTING button (9) a REV. (reverse) MODE button (14, 17, 18)
; a
COMPACT
DIGITAL AUDIO
STANDBY
CD
# / 8
TAPE FM/AM AUX
–
VOLUME
PHONES DOWN
4 7
UP
¢
REC
AUX
+
When using the remote control, point it at the remote sensor on the front panel.
5
01-05_FS-H300[J]6.p65
5 04.3.17, 11:42 AM
Getting Started
Unpacking
Do not connect the AC power cord until all other connections have been made.
Continued
Connecting Speakers
You can connect the speakers using the speaker cords.
After unpacking, check to be sure that you have all the following items.
The number in parentheses indicates the quantity of each piece supplied.
• AM loop antenna (1)
• Remote control (1)
• Batteries (2)
If any item is missing, consult your dealer immediately.
Connecting AM and FM Antennas
1 2,3
Red
1
AM loop antenna
(supplied)
Ò
Red
Speaker cord
Â
Black
Black
Speaker cord
FM ANTENNA
AM LOOP 2
FM antenna
Right speaker Left speaker
1
Connect the supplied AM loop antenna to the
AM LOOP terminal.
Place the antenna away from the unit and adjust its position for the best reception.
2
Adjust the position for the FM antenna for the best reception.
For better reception of both FM and AM
• Make sure the antenna conductors do not touch any other terminals or connecting cords.
• Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.
1
Hold the clamp of the speaker terminal.
2
Insert the end of the speaker cord into the terminal.
Match the polarity of the speaker terminals: red cord to
ª and black cord to · .
3
Release your finger from the clamp.
IMPORTANT:
• Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.
• DO NOT connect more than one speaker to one speaker terminal.
6
06-07_FS-H300[J]6.p65
6 04.3.17, 11:42 AM
Do not connect the AC power cord until all other connections have been made.
To remove the speaker grilles
The speaker grilles are removable as the illustration below.
Holes Projections
Putting the Batteries into the Remote Control
Insert the batteries—AAA/UM-4/R03—into the remote control by matching the polarity (+ and –) on the batteries with the + and – marking on the battery compartment.
When the remote control can no longer operate the unit, replace both batteries at the same time.
1
Speaker grille
To remove the speaker grille, insert your fingers around the projection at the top of the speaker grille, then pull gently towards you while holding the side.
Do the same for the rest of projections one at a time.
To attach the speaker grille, put the projections of the speaker grille into the holes of the speaker.
2
Connecting Other Equipment
To connect an audio equipment
You can connect audio equipment—used only as a playback device.
• DO NOT connect any equipment while the power is on.
• DO NOT plug in any equipment until all connections are complete.
For playing other equipment through this unit, connect between the audio output jacks on the other equipment and AUX jack by using audio cords with mini plugs (not supplied).
3
AAA/UM-4/R03
AUX
To audio output
L
R
OR
To audio output
To
Audio equipment
When the audio equipment has pin jacks for audio output:
Be sure that the pin plugs of the audio cords are colored— white plugs and jacks are for left audio signals, and red ones for right audio signals.
7
06-07_FS-H300[J]6.p65
7
• DO NOT use an old battery together with a new one.
• DO NOT use different types of batteries together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery compartment when you are not going to use the remote control for an extended period of time.
Otherwise, the remote control will be damaged from battery leakage.
NOW you are ready to plug in the unit.
IMPORTANT:
Be sure to check that all connections have been made before plugging in the power cord.
04.3.17, 11:42 AM
Common Operations
Continued
Setting the Clock
Before operating the unit any further, first set the unit’s clock.
When you plug in the power cord, “AM 12:00” starts flashing on the display.
You can set the clock when the unit is either turned on or in standby mode.
On the remote control ONLY:
1
Press CLOCK/TIMER.
The hour indication and AM (or PM) start flashing.
CLOCK
/TIMER
To adjust the clock
On the remote control ONLY:
1
Press CLOCK/TIMER repeatedly to show the current time indication.
The hour indication and AM (or PM) start flashing.
CLOCK
/TIMER
2
Repeat steps
2
and
3
on the left column.
2
Press UP or DOWN to adjust the hour, then press SET.
• When you press and hold UP or
DOWN, the hour indication changes continuously.
The minute indication starts flashing.
• The clock is working even while setting.
3
Press UP or DOWN to adjust the minute, then press SET.
• When you press and hold UP or
DOWN, the minute indication changes continuously.
The built-in clock starts.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
SET
UP
PRESET
GROUP
DOWN
PRESET
GROUP
SET
Turning On the Power
To turn on the unit, press STANDBY/ON .
The STANDBY lamp on the unit goes off.
• When you press the source button—CD
3
/
8
, TAPE
2 3
,
FM/AM and , the unit automatically turns on.
To turn off the unit (standby), press
STANDBY/ON again.
The STANDBY lamp on the unit lights red.
• “AM 12:00” flashes on the display until you
STANDBY/ON set the built-in clock. After setting the clock, the clock time will appear on the display while the unit is in standby mode.
• A little power is always consumed even while the unit is in standby mode.
To switch off the power supply completely, unplug the AC power cord from the AC outlet.
• When you unplug the AC power cord or if a power failure occurs
The clock is reset to “AM 12:00.” If this happens, set the clock again.
• The clock may gain or lose 1 to 2 minutes per month
If this happens, reset the clock.
Turning Off the Unit Automatically
(Auto Standby)
Using Auto Standby, the unit automatically turns itself off (on standby) about 3 minutes after playing back a disc or a tape.
• You can also turn off the unit automatically by using the
Sleep Timer. (See page 21.)
On the remote control ONLY:
To activate Auto Standby, press A.STANDBY.
The A.STANDBY
indicator appears on the display.
• When the playback is stopped, the
A.STANDBY
indicator starts flashing on the display.
A. STANDBY
To deactivate Auto Standby, press A.STANDBY again.
The A.STANDBY
indicator goes off.
8
08-09_FS-H300[J]6.p65
8 04.3.17, 11:43 AM
Selecting the Source
To select the source, press CD
6
, TAPE
2 3
, FM/AM, or
AUX.
• When you select CD as the source, playback starts automatically.
To operate the CD player, see pages 10 to 13.
To operate the tape deck, see page 14.
To operate the tuner (FM or AM), see pages 15 and 16.
To record on a tape, see pages 17 and 18.
To use an external equipment, see page 16.
Adjusting the Volume
You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOL MIN,”
“VOL 1” – “VOL 29,” and “VOL MAX.”
• The volume level has no effect on recording.
To increase the volume, press VOLUME + (or turn VOLUME control clockwise on the unit).
To decrease the volume, press VOLUME – (or turn VOLUME control counterclockwise on the
VOLUME unit).
• When you press and hold either button, you can change the volume level continuously.
Selecting the Sound Modes
You can select one of the 4 sound modes.
• This function also affects the sound from headphones.
• This function only affects the playback sound, and does not affect your recording.
On the remote control ONLY:
To select the sound modes, press SOUND/HBS repeatedly.
• Each time you press the button, the sound mode changes as follows:
ROCK POP CLASSIC
SOUND/HBS
FLAT
(Canceled)
JAZZ
ROCK: Powerful sound emphasizing treble and bass.
POP: More presence in the vocals and midrange.
CLASSIC: Enriched sound with fine treble and ample bass.
JAZZ: Accented lower frequencies for jazz-type music.
FLAT: Equalizer effect is canceled.
SOUND
When the sound mode is activated, the SOUND indicator lights up on the display.
For private listening
Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on the headphones.
DO NOT turn off (standby) the unit with the volume set to an extremely high level; Otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source.
REMEMBER you cannot adjust the volume level while the unit is in standby mode.
Reinforcing the Bass Sound
You can boost the bass sound.
• This function only affects the playback sound, and does not affect your recording.
On the remote control ONLY:
Press and hold SOUND/HBS.
• Each time you press and hold the SOUND/
HBS, HBS turns on and off.
BASS
SOUND/HBS
When the HBS is activated, the BASS indicator lights up on the display.
Fade-Out Muting (FADE MUTING)
On the remote control ONLY:
Press FADE MUTING.
The volume level decreases to “VOL MIN,” and
“MUTING” appears on the display.
FADE MUTING
To release muting, press FADE MUTING again. The volume level resumes to the previous level.
Checking the Clock Time During Play
On the remote control ONLY:
Press DISPLAY.
• Each time you press the button, the display changes the clock indication and the normal indication alternately. After changing the
DISPLAY display to the clock indication, operating any button or control also changes the display to the normal indication.
9
08-09_FS-H300[J]6.p65
9 04.3.17, 11:43 AM
Playing Back Discs
Continued
This unit has been designed to play back the following discs—CD, CD-R, and CD-RW.
You can play back the discs containing the tracks in music
CD format or MP3 files in ISO 9660 format.
• In this instruction, we call a disc recorded MP3 files “MP3 disc,” and “file” is also referred to as “track.”
When playing CD-Rs or CD-RWs
• Before playing CD-Rs or CD-RWs, read their instructions or cautions carefully.
• User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-
ReWritable) can be played only if they are already
“ finalized .”
• This unit supports “multi-session” discs (up to 5 sessions).
• This unit cannot play “packet write” discs.
• Some CD-Rs or CD-RWs may not play on this unit because of their disc characteristics, damage or stain on them, or if the player’s lens is dirty.
• CD-RWs may require a longer readout time. This is because the reflectance of CD-RWs is lower than for regular discs.
Notes for MP3 files
• The player can only recognize files with “MP3” or “mp3” as the extensions, which can be in any combination of upper and lower case. The file name needs to be up to 20 characters.
• This unit recognizes files and folders on a disc in the following conditions:
– up to 640 MP3 files.
– up to 256 folders (including the root folder).
– up to 8th layers (including the root folder).
• It is recommended that you record your material at a 44.1
kHz sampling rate, using the 128 kbps data transfer rate.
• Some MP3 files or discs may not be played back because of their characteristics or recording conditions.
• MP3 discs requires a longer readout time than normal discs because of the complexity of the folder/file configuration.
• MP3i and MP3 Pro are not available.
General notes
In general, you will have the best performance by keeping your discs and the mechanism clean.
• Store discs in their cases, and keep them in cabinets or on shelves.
• Keep the unit’s disc cover closed when not in use.
• Continued use of irregular shape discs (heart-shape, octagonal, etc.) can damage the unit.
Playing Back the Entire Disc—Normal Play
1
2
Press
)
OPEN on top of the unit.
The disc cover opens.
• You can insert a disc while listening to another source.
Place a disc correctly with its label side up.
Good Not good
3
Close the disc cover gently.
4
Press CD
6
.
The unit automatically turns on and the source changes to the CD player.
After loading the disc, the first track of the disc starts playing.
CD
3 / 8
When playing audio CD:
When playing MP3 disc:
MP3 indicator
MP3
Current track number
Elapsed playing time
Current track number
Elapsed playing time
• The disc automatically stops when the last track has finished playing.
While “READING” appears on the display
You cannot make any operation until the unit finishes reading the disc.
While playing back an MP3 disc
ID3 Tag information (the name of the title, artist, and album up to 30 characters) will be shown on the display. When the name is too long to be displayed at once, it is scrolled.
UP
PRESET
GROUP
To stop playing, press
7
.
The total track (or group) number and total playing time appear on the display.
DOWN
PRESET
GROUP
When stop playing audio CD:
When stop playing
MP3 disc:
Group folder indicator
MP3
Total track number
Total playing time
Total group number
Total track number
• Total playing time does not appear when MP3 disc is loaded.
10
04.3.17, 11:43 AM 10-14_FS-H300[J]6.p65
10
To remove the disc, press
)
OPEN on the unit, then take out the disc by holding it at the edges while pressing the unit’s pivot lightly.
To locate a particular point in a track
During play, press and hold ¢ or 4 (or
UP ¢ or DOWN 4 on the unit).
•
¢
(UP
¢
): Fast-forwards the tracks.
•
4
(DOWN
4
): Fast-reverses the tracks.
• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or CD-RW is inserted
Playback will not start.
• If no disc is inserted
“NO DISC” appears on the display.
While playing back an MP3 disc
This function is not available.
DO NOT open the disc cover by hand as it will be damaged.
Basic Disc Operations
While playing a disc, you can do the following operations.
To stop playing for a moment
During play, press CD 3 / 8 .
While pausing, current track number and elapsed playing time flash on the display.
To resume playing, press CD 3 / 8 again.
CD
3 / 8
To go to another track
Before or during play, press
¢
or
4
(or
UP
¢
or DOWN
4
on the unit) repeatedly.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
•
¢
(UP
¢
): Skips to the beginning of the next or succeeding tracks.
•
4
(DOWN
4
): Goes back to the beginning of the current or previous tracks.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
Programming the Track Playing Order
—Program Play
You can arrange the order in which tracks play before you start playing. You can program up to 40 tracks.
On the remote control ONLY:
1
Place a disc.
• If the current source is not the CD player, press
CD 6 , then 7 before going to the next step.
2
Press PROGRAM.
The PRGM (program) indicator appears on the display.
PROGRAM
PRGM
3
Press
¢
or
4
to select the track number, then press
PROGRAM.
Track number
Program step number
UP
PRESET
GROUP
DOWN
PRESET
GROUP
PROGRAM
To go to another track directly using the number buttons
On the remote control ONLY:
Pressing the number button(s) before or during play allows you to start playing the track number you want.
Ex.: For track number 5, press 5.
For track number 15, press OVER, then press 1, 5.
For track number 20, press OVER, then press 2, 0.
1
4
7
2
5
8
0
(For MP3 disc only)
For track number 20, press OVER, then press 0, 2, 0.
For track number 156, press OVER, then press 1, 5, 6.
3
6
9
OVER
PRGM
You can also use the number button(s) to select a track number.
• For the operation of the number buttons, see “To go to another track directly using the number buttons” on the left column.
1
4
7
When you are programming from MP3 disc
Pressing PRESET GROUP or PRESET GROUP selects the first track of each group.
2
5
8
0
3
6
9
OVER
11
10-14_FS-H300[J]6.p65
11 04.3.17, 11:43 AM
4
Repeat step
3
to program other tracks you want.
5
Press CD
3
/
8
.
The tracks are played in the order you have programed.
CD
3 / 8
If you try to program a 41st track
“– – FULL – –” will appear on the display.
To stop playing, press
7
.
Continued
Repeating Tracks—Repeat Play
You can have all the tracks, the program or individual track currently playing, repeat as many times as you like.
On the remote control ONLY:
Press REPEAT repeatedly before or during playback.
• Each time you press the button, Repeat Play changes as follows, and the following repeat indicators light up on the display:
REPEAT
UP
PRESET
GROUP
DOWN
PRESET
GROUP
To check the program contents
You can check the program contents by pressing
PROGRAM repeatedly before or after playback.
PROGRAM
To modify the program
Press PROGRAM repeatedly until the program step number you want to modify appears. Then follow step 3 of the programming procedure.
• Pressing 0 deletes the selected step.
PROGRAM
To add tracks in the program, press
PROGRAM repeatedly until “0” appears as the track number. Then follow steps 3 of the programming procedure.
PROGRAM
To clear the program
Press
7
before or after playback.
The PRGM indicator disappears from the display and all the memory contents will be erased (resumes to Normal Play).
• The programmed tracks are also erased in the following cases:
– Pressing
)
OPEN to open the disc cover.
– Turning off the unit.
– Changing the source.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
During Program Play
Auto Standby function does not take effect.
ALL
Repeat indicators
When playing back audio CD:
ALL
Canceled
ALL : In Normal Play, repeats all the tracks.
In Program Play, repeats all the tracks in the
: program.
Repeats one track.
When playing back MP3 disc:
ALL
Canceled
GR.
ALL : In Normal Play, repeats all the tracks.
In Program Play and Random Play, repeats all the tracks in the program.
GR.
: In Normal Play, repeats all the tracks in a
: group.
In Program Play and Random Play, this function is not available.
Repeats one track.
In Random Play, this function is not available.
To cancel Repeat Play, press REPEAT repeatedly until the repeat indicator goes off.
REPEAT
12
10-14_FS-H300[J]6.p65
12 04.3.17, 11:43 AM
Playing at Random—Random Play
You can play the tracks at random.
On the remote control ONLY:
Press RANDOM.
The RANDOM indicator lights up on the display.
RANDOM
RANDOM
To exit from Random Play, press
7 or RANDOM.
The RANDOM indicator goes off.
• It is not possible to activate the Random Play function during Program Play.
Displaying the Remaining Time during
Playback
You can display the remaining time of the current track/disc and the elapsed time of the current track/disc during playing.
On the remote control ONLY:
Press REMAIN repeatedly.
REMAIN
When playing back audio CD:
• Each time you press the button, the display changes as follows, and the following remain indicators light up on the display:
REMAIN
TOTAL REMAIN
Remain indicators
TOTAL REMAIN *
(No Indication)
REMAIN : Shows the remaining time of the current track.
TOTAL REMAIN : Shows the remaining time of the disc.
No indication: Shows the elapsed time of the current track.
* Remaining time of the disc (TOTAL REMAIN) will not be displayed in the following cases:
– During Random Play.
– During Program Play.
When playing back MP3 disc:
• Each time you press the button, the display changes as follows:
ID3 Tag information *
Normal indication
Folder name ** /file name
* ID3 Tag information shows the name of the title, artist, and album in sequence.
If the file does not have any information, “NO INFO” appears.
** When a file does not belong in any folder, “ROOT” appears.
13
10-14_FS-H300[J]6.p65
13 04.3.17, 11:43 AM
Playing Back Tapes
Playing Back a Tape
You can play back type I tapes only.
1
Press PUSH OPEN.
The cassette holder opens.
PUSH OPEN
If no cassette is inserted when you press TAPE ¤ ‹
“NO TAPE” appears on the display.
To stop playing, press 7 .
UP
PRESET
GROUP
DOWN
PRESET
GROUP
DOWN
4 7
UP
¢
2
Put a cassette in with the exposed part of the tape down.
To fast-wind to the left or to the right, press ¢ or 4 (or UP ¢ or
DOWN 4 on the unit).
The tape direction indicator ( 3 or 2 ) starts flashing rapidly on the display.
DOWN
4
UP
PRESET
GROUP
DOWN
PRESET
GROUP
7
UP
¢
To remove the cassette, press PUSH OPEN on the unit while playback is stopped.
PUSH OPEN
3
Close the cassette holder gently.
• When a tape is inside of the cassette holder, the tape direction indicator (
3
) lights up on the display.
4
Press TAPE
¤ ‹
.
Playback starts (if the unit has been on
TAPE standby, the unit automatically turns on).
The tape direction indicator (
3
or
2
) starts flashing slowly on the display.
• Each time you press the button, the tape direction changes:
3
: plays the front side.
2
: plays the reverse side.
When the tape plays to the end, the deck automatically stops if the Reverse Mode is set to or . (See “To play both sides—Reverse Mode.”)
To play both sides—Reverse Mode
You can set the deck to play just one side of a tape, both sides once, or both sides continuously.
On the remote control ONLY:
Press REV.MODE (reverse mode).
• Each time you press the button, the Reverse
Mode changes as follows:
REV.MODE
: The deck automatically stops after playing both sides of the tape. Stops when playback in the 2 direction is finished.
: The deck continues to play both sides of the tape 10 times, then stops playback automatically.
: The deck automatically stops after playing one side of the tape.
• DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be damaged.
• The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch rollers and the capstans.
• This unit is not compatible with type II and type
IV tapes.
14
04.3.17, 11:43 AM 10-14_FS-H300[J]6.p65
14
Listening to FM and AM Broadcasts
Tuning in to a Station
1
Press FM/AM to select either “FM” or “AM.”
FM/AM
The unit automatically turns on and tunes in to the previously received station—either FM or AM.
• Each time you press the button, the band alternates between FM and AM.
MHz
• If the station previously selected is stored in a preset number, the preset number will appear instead of “FM” or “AM.”
2
Press and hold
¢
or
4
(or
UP
¢
or DOWN
4
on the unit) for more than 1 second.
•
¢
(UP
¢
): Increases the frequencies.
•
4
(DOWN
4
): Decreases the frequencies.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in.
• If an FM program is broadcast in stereo, the ST (stereo) indicator lights up on the display (only when the reception is good).
To stop during searching, press
¢
or
4
(or UP
¢ or
DOWN
4
on the unit).
When you repeatedly press ¢ or 4 (or UP ¢ or
DOWN
4
on the unit)
The frequency changes step by step.
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the
“MONO” appears on the display. The MONO indicator also lights up. Reception will improve.
FM MODE
To restore the stereo effect, press FM MODE again so that
“STEREO” appears on the display and the MONO indicator goes off. In stereo mode, you can hear stereo sound when a stereo program is broadcast.
The stereo effect also restores when:
• Changing the band (FM or AM).
• Changing the station frequency.
• Changing the playing source.
• Turning off (or on) the unit.
Presetting Stations
You can preset 25 FM and 15 AM stations manually.
In some cases, test frequencies have been already stored for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start again from step 2 .
On the remote control ONLY:
1
Tune in to the station you want to preset.
• See “Tuning in to a Station” on the left column.
2
Press SET.
“00” starts flashing on the display.
SET
MHz
PRGM
3
Press PRESET GROUP or
PRESET GROUP to select a preset number, then press SET.
The preset station is stored in memory.
• Even if you do not press SET, the station will automatically be stored on the selected preset number 5 seconds later.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
MHz
PRGM
You can also use the number button(s) to select a preset number.
• In this case, you do not have to press SET.
Ex.: To select a preset number 5, press 5.
To select a preset number 15, press
OVER, then press 1, 5.
1
4
7
To select a preset number 20, press OVER, then press 2, 0.
2
5
8
0
4
To preset more stations, repeat steps
1
to
3
above, allocating a different preset number to each station.
• Storing a new station on an already assigned number erases the previously stored one.
3
6
9
OVER
When you unplug the AC power cord or if a power failure occurs
The preset stations will remain in the unit.
15
15-16_FS-H300[J]6.p65
15 04.3.17, 11:43 AM
Tuning in to a Preset Station
On the remote control ONLY:
1
Press FM/AM to select either “FM” or “AM.”
FM/AM
The unit automatically turns on and tunes in to the previously received station—either FM or AM.
• Each time you press the button, the band alternates between FM and AM.
2
Press PRESET GROUP or
PRESET GROUP repeatedly to select a preset number.
UP
PRESET
GROUP
DOWN
PRESET
GROUP
To tune in to a preset station directly using the number buttons
On the remote control ONLY:
Pressing the number button(s) allows you to select the preset number you want.
Ex.: For preset number 5, press 5.
For preset number 15, press OVER, then press 1, 5.
For preset number 20, press OVER, then press 2, 0.
1
4
7
2
5
8
0
3
6
9
OVER
Using an External Equipment
Listening to the External Equipment
You can listen to the external equipment such as MD recorder, cassette deck, or other auxiliary.
• First, make sure that the external equipment is properly connected to the unit. (See page 7.)
1
Set the volume level to the minimum position.
2
Press AUX.
“AUX” appears on the display.
AUX
To exit AUX mode, select other source.
For operation of the external equipment
Refer to its instructions.
3
Start playing the external equipment.
4
Adjust the volume level to the level you want to listen to.
04.3.17, 11:43 AM
16
15-16_FS-H300[J]6.p65
16
Recording
IMPORTANT:
• It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable program and in any literary, dramatic, musical, or artistic embodied therein.
• The recording level is automatically set correctly, so it is not affected by the other sound settings. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.
• If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase the distance between the TV and the unit.
• You can only use type I tape for recording.
3
Start playing the source—FM, AM, or auxiliary equipment connected to AUX jack.
• When the source is FM or AM, tune in to the station you want to record.
• When recording from discs, see “Recording Discs—
Disc Synchronized Recording” on page 18.
4
Press REC (recording).
• The REC indicator appears and
3
indicator lights up on the display.
REC
REC
MHz
5
Press TAPE
¤ ‹
.
3
indicator starts flashing and the recording starts.
TAPE
• DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be damaged.
• DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.
• The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch rollers and the capstans.
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus, when recording from discs, FM/AM broadcasts, or external equipment, wind the leader tape first to ensure that the recording will be made without losing any music.
• If no cassette is inserted when you press REC
“NO TAPE” appears on the display.
• If a protected tape is inserted when you press REC
“PROTECT” appears on the display.
To stop recording for a moment, press REC.
The recording is paused. To resume recording, press TAPE
¤ ‹
.
DOWN
4
To stop recording, press
7
.
The recording stops.
7
REC
UP
¢
To protect your recordings
Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with adhesive tape.
To remove the cassette, press PUSH OPEN while recording is stopped.
PUSH OPEN
Recording on a Tape
On the unit ONLY:
Adhesive tape
1
Put a recordable cassette in with the exposed part of the tape down.
• See also page 14.
2
Close the cassette holder gently.
To record on both sides—Reverse Mode
On the remote control ONLY:
Press REV.MODE (reverse mode) until
or is lit.
• When using the Reverse Mode for recording,
lights up and start recording in the forward
( 3 ) direction first.
REV.MODE
To cancel the Reverse Mode, press REV.MODE repeatedly until is lit.
To reduce the beat—Beat Cut
On the remote control ONLY:
If the beats are heard while recording an AM broadcast, press BEAT CUT repeatedly until the beats are reduced.
• Each time you press the button, the display alternates between “CUT-1” and “CUT-2.”
BEAT CUT
17
17-18_FS-H300[J]6.p65
17 04.3.17, 11:43 AM
Recording Discs
—Disc Synchronized Recording
You can start disc play and recording at the same time.
On the unit ONLY:
1
Put a recordable cassette in with the exposed part of the tape down.
• See also page 14.
2
Close the cassette holder gently.
3
Press CD
‹
/
8
to select the CD player as the source.
CD
#
/
8
4
Press
7
to stop the disc playback.
• You can make a program (see page
11) if you want.
5
Press REC (recording).
3
indicator lights up on the display.
DOWN
4
REC
7
REC
To stop recording for a moment, press REC.
Both the CD playback and tape recording are paused. To resume recording, press TAPE
¤ ‹
.
REC
To stop recording, press 7 .
The recording stops and the CD playback is paused.
DOWN
4 7
UP
¢
UP
¢
To record on both sides—Reverse Mode
On the remote control ONLY:
Press REV.MODE (reverse mode) repeatedly until or is lit.
REV.MODE
• When using the Reverse Mode for Disc
Synchronized Recording, lights up and the recording starts in the forward (
3
) direction first. When the tape reaches its end, the CD playback is paused until the tape recording changes to the reverse direction, then the recording continues.
To cancel the Reverse Mode, press REV.MODE repeatedly until is lit.
When making Sleep Timer settings while doing Disc
Synchronized Recording
Set enough time to allow for the disc to finish playing; otherwise, the power will go off before recording is completed.
6
Press TAPE
¤ ‹
.
“SYNC REC” appears and 3 indicator starts flashing slowly on the display.
CD playback and tape recording starts automatically.
REC
TAPE
• If no cassette is inserted when you press REC
“NO TAPE” appears on the display.
• If a protected tape is inserted when you press REC
“PROTECT” appears on the display.
04.3.17, 11:43 AM
18
17-18_FS-H300[J]6.p65
18
Using the Timers
There are four timers available—Daily Timer, Recording
Timer, Snooze Timer, and Sleep Timer.
• Before using these timers, make sure the built-in clock is set correctly (see page 8).
Using Daily Timer and Recording Timer
You can set the timer whether the unit is on or off.
How the Timer actually works
When the on-time comes, the unit automatically turns on (the
[timer] indicator flashes and continues flashing while the timer is operating). Then, when the off-time comes, the unit automatically turns off (standby). The timer setting remains in memory until you change it.
• When the (timer) and DAILY 1 , 2 , or 3 indicators are lit on the display, the timer acts as the Daily Timer. Once the timer has been set, it will be activated at the same time and automatically turns off (standby) after 60 minutes everyday until the timer is deactivated.
• When the (timer) and the REC indicators are lit on the display, the timer acts as the Recording Timer. After the timer-recording finishes, the details of the setting remain stored but the timer is turned off.
Before you start...
When using “TUNER” as the source to play, make sure to select the desired station before turning off the power.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start again from step 1 .
On the remote control ONLY:
1
Press CLOCK/TIMER repeatedly to select the timer you want to adjust and activate—Daily 1, Daily 2, Daily
3, or Rec.
CLOCK
/TIMER
The timer setting and hour indication start flashing on the display.
Each time you press the button, the display changes as follows:
Daily 1 Timer
ON
DAILY 1
ON
DAILY 2
ON
DAILY 3
ON
REC
Daily 2 Timer
Daily 3 Timer
Rec Timer
Clock setting
Normal indication
2
Set the on-time you want the unit to turn on.
(1) Press UP or DOWN to set the hour,
UP
PRESET
GROUP then press SET.
(2) Press UP or DOWN to set the minute, then press SET.
If you want to change the time setting, press CANCEL.
DOWN
PRESET
GROUP
• If you are setting the Daily Timer, the source name starts flashing on the display.
\ Go to step 4 .
• If you are setting the Recording Timer, the OFF indicator and hour indication start flashing on the display.
SET
19
19-21_FS-H300[J]6.p65
19 04.3.17, 11:43 AM
Continued
3
For the Recording Timer ONLY:
Set the off-time you want the unit to turn off.
OFF
REC
(1) Press UP or DOWN to set the hour, then press SET.
(2) Press UP or DOWN to set the minute, then press SET.
If you want to change the time setting, press CANCEL.
• The Recording Timer is activated. The
(timer) and REC indicators light up. The display returns to the normal indication.
\
Go to step 7 .
4
Press UP or DOWN to select the source to play.
DAILY 1
UP
PRESET
GROUP
DOWN
PRESET
GROUP
SET
UP
PRESET
GROUP
DOWN
PRESET
GROUP
Each time you press the button, the source changes as follows:
TUNER TAPE CD
To deactivate the timer, press and hold DAILY TIMER/SNOOZE.
• Each time you press and hold the button, the timer setting changes as follows:
DAILY 1
Canceled
DAILY 2
REC
DAILY 3
To change the timer, repeat steps 1 to 6 on pages 19 and this page.
• To activate the Daily Timer again without changing the setting, press DAILY TIMER/SNOOZE on the unit repeatedly to select the timer number you want.
When there is no playing source (either a cassette tape or a disc) inside when you select “TAPE” or “CD”
The source to play is changed to “TUNER” when the on-time comes.
If the unit is already turned on when the timer on-time comes
The timer does not work.
When you unplug the AC power cord or if a power failure occurs
The timer setting remains. Set the built-in clock and activate the timer again.
• Make sure the playing source (either a cassette tape or a disc) is inside when you select “TAPE” or “CD.”
If you want to change the time setting, press CANCEL repeatedly to return step 2 .
5
Press SET.
The (timer) and active daily timer number indications lights up. The display returns to the normal indication.
6
Press VOLUME +/– to adjust the volume for the on-time.
VOLUME
SET
7
Press STANDBY/ON to turn off the unit if you have set the timer with the unit turned on.
STANDBY/ON
Using Snooze Timer
The Snooze Timer turns off the unit (standby) only for 5 minutes while Daily Timer is in operation.
• You can set the Snooze Timer only while the Daily Timer is in operation.
On the unit ONLY:
Press DAILY TIMER/
SNOOZE while Daily Timer is in operation.
The unit turns off (standby) and the SNOOZE indicator appears on the display.
After 5 minutes, the unit automatically turns on with the source you selected in step 4 on the left column.
On the unit ONLY:
To activate the timer, press and hold
DAILY TIMER/SNOOZE on the unit repeatedly to select the timer number you want.
If the unit is turned on when the Snooze Timer is working
Both Snooze Timer and Daily Timer will be canceled.
If you set the Snooze Timer when there is less than 5 minutes until the Daily Timer off-time
The unit will not turn on even when 5 minutes passed.
When you unplug the AC power cord or if a power failure occurs
The timer will be canceled. You need to set the clock first, then the timer again.
20
19-21_FS-H300[J]6.p65
20 04.3.17, 11:43 AM
Using Sleep Timer
With Sleep Timer, you can fall asleep to your favorite music or radio program.
• You can set Sleep Timer only when the unit is turned on.
• You can also turn off the unit automatically by using Auto
Standby. (See page 8.)
How the Sleep Timer actually works
The unit automatically turns off after the specified length of time passes.
On the remote control ONLY:
1
Press SLEEP.
The SLEEP indicator starts flashing on the display.
SLEEP
SLEEP
When you set the Sleep Timer after the Daily Timer starts playing the selected source
The unit turns off with either timer having an earlier shut-off time.
If you set the Sleep Timer while playing back or recording a tape
Do not shut the unit off with the Sleep Timer while a tape is running.
If the unit turns off while playing back or recording a tape, the cassette deck or tapes may be damaged.
• Each time you press the button, the length of time changes as follows:
10 20 30 60
OFF
(canceled)
120 90
2
Wait for about 5 seconds after specifying the length of time.
The SLEEP indicator remains lit on the display.
To check the remaining time until shut-off time, press
SLEEP once. The remaining time until shut-off time appears for about 5 seconds.
To change the shut-off time, press SLEEP repeatedly until the length of time you want appears.
To cancel the setting, press SLEEP repeatedly until the
SLEEP indicator goes off and display returns to the normal indication.
• Turning off the unit also cancels the Sleep Timer.
21
19-21_FS-H300[J]6.p65
21 04.3.17, 11:43 AM
Maintenance
To get the best performance of the unit, keep your discs, tapes and mechanism clean.
General Notes
In general, you will have the best performance by keeping your discs, tapes and the mechanism clean.
• Store discs and tapes in their cases, and keep them in cabinets or on shelves.
Cleaning the unit
• Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
• Since the unit may deteriorate in quality, become damaged or have its paint peel off, be careful about the following:
– DO NOT wipe it with a rough cloth.
– DO NOT wipe it too vigorously.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as an insecticide to it.
– DO NOT allow any rubber or plastic to remain in contact with it for a long time.
Handling discs
• Remove the disc from its case by holding it at the edge while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
Handling cassette tapes
• If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.
• If the tape is loose, it may get stretched, cut, or caught in the cassette.
• Be careful not to touch the tape surface.
• Avoid storing tapes in any of the following places:
– In dusty places
– In direct sunlight or heat
– In moist areas
– On a TV or speaker
– Near a magnet
To keep the best recording and playback sound quality
You need to clean the heads.
• Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and audio shops).
When the head becomes dirty, the following symptoms will occur:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any metallic or magnetic tools.
Capstan
Head
To clean the disc
Wipe the disc with a soft cloth in a straight line from center to edge.
Pinch Roller
To demagnetize the head
Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).
DO NOT use any solvent—such as conventional record cleaner, spray, thinner, or benzine—to clean the disc.
22
22-24_FS-H300[J]6.p65
22 04.3.17, 11:43 AM
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer for service.
Symptom
Power does not come on.
No sound is heard.
Hard to listen to broadcasts because of noise.
The disc does not play.
Impossible to record.
Operations are disabled.
Unable to operate the unit by the remote control.
Possible Cause
The power cord is not connected to an
AC outlet.
• Connections are incorrect or loose.
Action
Insert the plug into the socket.
• A pair of headphones is connected.
• Check all connections and make corrections. (See pages 6 and 7.)
• Unplug the headphones from the
PHONES jack.
• It cannot be played. Replace the disc.
• MP3 disc is recorded with “packet writing.”
• Antennas are disconnected.
• The AM loop antenna is too close to the unit.
• The FM antenna is not properly extended and positioned.
The disc is upside down.
Small tabs on the back of the cassette are removed.
The built-in microprocessor has malfunctioned due to external electrical interference.
• The path between the remote control and the remote sensor on the unit is blocked.
• The batteries are exhausted.
• You are using the remote control too far from the unit.
• Reconnect the antenna correctly and securely.
• Change the position and direction of the AM loop antenna.
• Extend FM antenna and orient to the best reception position.
Put the disc in with the label side up.
Cover the holes with adhesive tape.
Unplug the AC power cord then plug it back in.
• Remove the obstruction.
• Replace the batteries. (See page 7.)
• Signals cannot reach the remote sensor. Move closer to the unit.
23
22-24_FS-H300[J]6.p65
23 04.3.17, 11:43 AM
Specifications
Design and specifications are subject to change without notice.
Amplifier Section—CA-FSH300
Output Power:
20 W per channel, min. RMS, driven into 4
Ω
at 1 kHz with no more than 10% total harmonic distortion.
Audio input sensitivity/Impedance (at 1 kHz)
AUX: 500 mV/50 k Ω
Speakers Impedance: 4
Ω
– 16
Ω
Tuner
FM tuning range:
AM tuning range:
CD player
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
87.5 MHz—108.0 MHz
530 kHz—1 710 kHz
85 dB
85 dB
Immeasurable
Cassette deck
Frequency response:
Normal (type I):
Wow and flutter:
100 Hz—10 000 Hz
0.35% (WRMS)
General
Power requirement:
Power consumption:
AC 120 V , 60 Hz
40 W (at operation)
2 W (on standby)
Dimensions (W/H/D) (approx.):
Mass (approx.):
152 mm x 233 mm x 292 mm
(6 in. x 9 3 /
16
in. x 11 1 /
2
in.)
3.9 kg (8.6 lbs)
Supplied accessories
See page 6.
Speaker Section—SP-FSH300
Type:
Speakers:
Full range, bass-reflex type
10 cm cone x1
Power handling capacity: 20 W
Impedance: 4
Ω
Frequency range: 100 Hz—15 kHz
Dimensions (W/H/D) (approx.):
Mass (approx.):
147 mm x 233 mm x 189 mm
(5 13 /
16
in. x 9 3 /
16
in. x 7 1 /
2
in.)
1.9 kg (4.2 lbs) each
04.3.17, 11:43 AM
24
22-24_FS-H300[J]6.p65
24
LIMITED WARRANTY
AUDIO-1
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS LABOR
1
YR
1
YR
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model number or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No. :
Purchase data :
Serial No. :
Name of dealer :
04.3.17, 11:43 AM FS-H300[J]warranty.p65
2
Authorized Service Centers
®
QUALITY SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
http://www.jvc.com
Dear Customer,
In order to receive the most satisfaction from your purchase,please read the instruction booklet before operating the unit.In the event that repairs are necessary, please call 1 (800)537-5722 for your nearest authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Do not service the television yourself
Caution
To prevent electrical shock,do not open the cabinet.There are no user serviceable parts inside.Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product,please call toll free:1 (800)882-2345 or on the web at www.JVC.com
BT-51001-5
(0301)
FS-H300[J]warranty.p65
3 04.3.17, 11:43 AM
MEMO memo_HX-Z77D&55D[U]fff.p65
1 04.2.18, 9:30 AM
MEMO memo_HX-Z77D&55D[U]fff.p65
1 04.2.18, 9:30 AM
VICTOR COMPANY OF JAPAN, LIMITED
EN
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
FS-H300[J]cover5.p65
2 04.3.17, 11:46 AM
0304AIMMDWORI
advertisement
Related manuals
advertisement
Table of contents
- 6 Location of the Buttons and Controls
- 6 Main Unit
- 8 Remote Control
- 9 Getting Started
- 9 Unpacking
- 9 Connecting AM and FM Antennas
- 9 Connecting Speakers
- 10 Connecting Other Equipment
- 10 Putting the Batteries into the Remote Control
- 11 Common Operations
- 11 Setting the Clock
- 11 Turning On the Power
- 11 Turning Off the Unit Automatically (Auto Standby)
- 12 Selecting the Source
- 12 Adjusting the Volume
- 12 Fade-Out Muting (FADE MUTING)
- 12 Selecting the Sound Modes
- 12 Reinforcing the Bass Sound
- 12 Checking the Clock Time During Play
- 13 Playing Back Discs
- 13 Playing Back the Entire Disc—Normal Play
- 14 Basic Disc Operations
- 14 Programming the Track Playing Order—Program Play
- 15 Repeating Tracks—Repeat Play
- 16 Playing at Random—Random Play
- 16 Displaying the Remaining Time during Playback
- 17 Playing Back Tapes
- 17 Playing Back a Tape
- 18 Listening to FM and AM Broadcasts
- 18 Tuning in to a Station
- 18 Presetting Stations
- 19 Tuning in to a Preset Station
- 19 Using an External Equipment
- 19 Listening to the External Equipment
- 20 Recording
- 20 Recording on a Tape
- 21 Recording Discs—Disc Synchronized Recording
- 22 Using the Timers
- 22 Using Daily Timer and Recording Timer
- 23 Using Snooze Timer
- 24 Using Sleep Timer
- 25 Maintenance
- 26 Troubleshooting
- 27 Specifications