NOIDS POT EXT2020 User Manual

EN
All-in-One Herb Cooker
POT by NOIDS I
Model EXT2020
User Manual
For users of Pot by NOIDS
NDPN-20200301 Version EN-0
NOIDS is a Registered Trade Mark of NOIDS B.V.
Putsteeg 99, 5481XT, SCHIJNDEL, The Netherlands
© NOIDS B.V.
EN
Read this manual carefully, it contains all the instructions for maintaining the
appliance’s functional qualities. For any further information please visit:
www.noids.green
CONTENTS
1. Instructions
1.1
Introduction 1
1.2
This user manual 1
1.3
Intended use1
1.4
General safety instructions1
1.5
For Pot by NOIDS I
1.6
Manufacturer liability2
1.7
Identification plate 2
1.8
Disposal 2
2
2. Description
2.1
Product overview3
2.2
Glass Set3
2.3
Filter Set3
2.4
Main Body4
2.5
Functions4
2.6
Technical parameters and compliance
4
3.1
Before first use 5
3.2
Operation - General
5
3.3
Operation - CBD Decarb & Decarb
5
3.4
Operation - CBD Oil & Oil
6
3.5
Operation - Filter the oil 6
3.6
Operation - Gather the remaining oil 6
3.7
Operation - Evaporation
7
3. Use
4. Cleaning & Care
4.1
Instructions7
4.2
Cleaning the surfaces 8
4.3
Ordinary daily cleaning 8
4.4
Food stains or residues 8
4.5
Cleaning the Glass8
4.6
Cleaning the Filter Set8
5. Troubleshooting
5.1
Before troubleshooting8
5.2
What to do if...8
The manufacturer reserves the right to make any changes deemed useful for improvement of
this product without prior notice. The illustrations and descriptions contained in this manual are
therefore not binding and are merely indicative.
EN
1. Instructions
1.1 Introduction
Key information for the user:
General information on
Description of the
Information on the use
Information for correct
Information on what
this user manual, on
appliance and its
of the appliance and
cleaning and care of
can go wrong and what
safety and final disposal
accessories
its accessories, cooking
the appliance
can be done
advice
Safety instructions
Information
User hints & tips
1.2 This user manual
This user manual is an integral part of the appliance and must therefore be kept in its entirety
and within the user’s reach for the whole working life of the appliance.
1.3 Intended use
• Use the appliance only indoors.
• This appliance has been designed exclusively for domestic use.
Do NOT use the appliance for commercial or any other purposes.
• This appliance has been designed and tested exclusively for herbs with
medicinal properties.
Danger of poison
- Consumption of unknown or unidentified plants may lead to human intoxication, organ damage, and even death.
- Always consult a qualified physician for the potential risk before using any medicinal blossoms and herbs.
• Carefully follow the notes and suggestions provided in this user manual.
• Only use the appliance for (1) decarboxylation of plant material, (2) oil infusion using plant
material, and (3) evaporation of liquid. Do NOT use the appliance for anything other than the
intended use.
• If food or other substances were to come into contact with the heating elements, they may
cause unpleasant odour and may damage the appliance.
• This appliance is not designed to operate with external timers.
• This appliance may not be used by children aged under 12 and by people of reduced physical
and mental capacity, or lacking in experience in the use of electrical appliances. They must be
supervised or instructed by adults or those who are responsible for their safety.
• Children must never play with the appliance. Keep the appliance out of children’s reach.
All NOIDS products follow strict quality control procedures, including testing
Based on random sampling. Such testing may leave some traces of use on a tested product.
1.4 General safety instructions
• Read this user manual carefully before using the appliance.
• Do NOT immerse the Main Body of the appliance, the power cord or the Base in
water or any other liquid.
• Do NOT use the appliance when the power cord or the plug is damaged or when the appliance
has fallen or is damaged in any manner.
• Do NOT place the appliance on or near a burning gas or an electrical stove or in a heated oven.
• The cord is short to prevent accidents. Do NOT use an extension cord.
• Do NOT let the power cord hang over the edge of a table or a worktop etc. where the appliance
can be pulled down or fall.
• Switch off the appliance immediately after use.
• Do NOT modify this appliance.
• Do NOT operate on the appliance with wet hands.
• Always place the appliance on a flat, stable, heat-resistant worktop.
• If the power cord or the adaptor is damaged, stop using the appliance and contact technical
support immediately.
1
EN
• Do NOT try to repair the appliance yourself or without the intervention of a qualified engineer.
In case of a fault, repairs should only be carried out by a qualified engineer.
• Please check the labelled voltage and make sure that the appliance is suitable for operating
with the electricity supply system safely and efficiently.
• When Disconnecting the power cord from a socket, always pull the plug, not the cord.
1.5 For Pot by NOIDS I
• Do NOT touch the Glass without the Sleeve when the ventilation fan inside the cooker is operating, the content and the Glass can be very hot. Let the Glass cool down to safe temperature first.
• Do NOT touch the inner heating surface of the Main Body when the fan inside the cooker is
operating, the inner heating surface can be very hot.
CAUTION: Hot Surface
- The inner heating surface and the Glass content can be very hot during and
immediately after operation.
The ventilation fan inside the Main Body keeps on working unless the temperature of the inner heating surface drops to 50 ºC / 122 ºF.
• Do NOT move the cooker when it is operating.
• Do NOT apply the Filter Set to the Glass while the Glass is inside the Main Body. Oil or liquid
may be ejected via the Spout and come into contact with the Main Body.
• Do NOT use the Filter Set on the Glass before the Glass cools down to safe temperature. Hot
oil or air may be ejected via the Spout.
• Do NOT place the Glass or the cooker directly on a hot surface or over open flame.
• Do NOT use the Glass in an oven or microwave oven.
• Do NOT heat the Glass on an induction cooker.
• Do NOT hit the Glass with hard objects, or manually drop the Glass from a height. If the Glass
is cracked, stop using it immediately and contact our authorized distributor or NOIDS support
team for replacement.
• Keep the cooker and the power cord away from heat, moisture, slippery surfaces and sharp
edges.
• Do NOT replace the Glass with any unauthorized container. The matching NOIDS Glass has a
highly sensitive built-in thermal sensor. Unauthorized container will not be recognized by the
cooker.
• Electrical appliances may burn, do NOT use the cooker near or below combustible materials.
• ALWAYS remove the plug from the socket when the cooker is not in use or before cleaning.
• ALWAYS remove the plug from the socket when the cooker is not working properly.
• Make sure that the air around the cooker can circulate freely. Do NOT place anything on top of
it.
• Make sure that the silicon Sleeve is properly put on the Glass during operation.
1.6 Manufacturer liability
The manufacturer declines all liability for damage to persons or property caused by:
• Use of the appliance other than the one envisaged;
• Not having read the user manual;
• Tampering with any part of the appliance;
• Use of non-original spare parts;
• Not following the safety instructions
1.7 Identif ication plate
The identification plate bears the technical data, serial number and brand name of the appliance.
Do not remove the identification plate for any reason.
1.8 Disposal
This appliance must be disposed of separately from other waste (Directives 2012/19/
EU, 2011/65/EU). The appliance does not contain substances in quantities sufficient
to be considered hazardous to health and the environment, in accordance with
current European Directives.
2
EN
Power voltage. Danger of electrocution
- Disconnect the main power supply.
- Disconnect the power cable from the electrical system.
• Old appliances do not belong in household waste! To comply with current legislation, old appliances, having reached the end of their useful lives, should be taken to a disposal facility where
they can be sorted. In this way, any valuable material contained in the old appliances can be
recycled and the environment protected. Responsible local authorities or their waste disposal
operators can provide further information. The appliance is packed in non-polluting and
recyclable materials.
• Dispose of the packing materials at an appropriate disposal facility.
• NOIDS products have achieved zero plastic in packaging by careful and responsible design.
Nevertheless, third party logistic might use plastic for delivery. Dispose third party plastic
responsibly according to local regulations.
2. Description
2.1 Product overview
1
2
3
1. Main Body
integrates the heating element and the Rotary Control
2. Glass Set
a Glass with scale marks and a built-in sensor, a Sleeve for heat
4
insulation, and a Dish Lid
3. Filter Set
a Filter Disc, a Funnel with a Spout, a Support Lid, a Glass pipette
and a Lock Ball for collecting every last drop of oil
4. Brush made of wool, for cleaning narrow parts in the Filter Set
2.2 Glass Set
1
1. Dish Lid
2
covers the Glass during operation and serves as
an evaporation dish when needed
2. Sleeve
seals heat during operation and reduces the risk
of burning
3. Glass 3
container with a highly sensitive build-in sensor
that monitors the temperature during operation
4. Sensor Pad
secures the built-in thermal sensor to the Glass
4
1
2
2.3 Filter Set
3
1. Spout liquid outlet
2. Finger Grip
for pressing down and lifting up the Filter Disc
3. Support Lid
stabilizes the Filter Set
6
4. Filter Funnel gathers the oil towards the Spout
5. Filter Disc
separates plant material and liquid
6. Pipette
collects the last drops of oil
7. Lock Ball
secures the Pipette or the Mesh to the Spout
4
7
5
3
EN
1
2.4 Main Body
1. Protection Ring
insulates heat
2. Rotary Control
for function selection
3. Function Mark
specific function
4. Base Mark to align functions
5. LED Light indicates a function is activated
2
3
2.5 Functions
4
5
The Rotary Control is used to select one of the 5 working functions or the OFF function. Once
connected to power, the Point LED Lights up above the Base Mark to show the cooker is connected to power and in standby mode. By simply turning the Rotary Control body, a function
circle can be activated.
A function cycle has 2 parts: heating and cooling. Heating is indicated by the pulsating Ring LED,
and cooling is indicated by the sound of working fan inside the Main Body. Only when the temperature of the heating surface drops to safe temperature (50ºC/ 122 ºF), the fan stops working
and the function cycle is complete.
OFF function
Cancel or stop any function cycle at any time
CBD Oil
Careful Bio-Decarb Oil function - infuse bio-active compounds into liquid oil
using herbs activated by the CBD Decarb function
≈180min / 100ºC / 212ºF
CBD Decarb
Careful Bio-Decarb function - decarboxylate the sensitive medicinal herbs that
requires lower temperature and longer time for activation
≈120min / 110ºC / 230°F
Decarb
General Decarb function - decarboxylate herbs
≈100min / 115ºC / 239°F
Oil
General Oil function - infuse bio-active compounds into liquid oil using herbs
activated by the general Decarb function
≈160min / 100ºC / 212ºF
Evaporation
Evaporation function - reduce the volume of infused liquid which has a boiling
point no higher than 100ºC / 212 ºF
Max. 102ºC / 215,6°F
No light on:
Disconnected from power
Point LED on:
Standby
Ring LED on and pulsates:
Heating
Fan working:
Temperature above 50 ºC / 122 ºF
2.6 Technical parameters and compliance
Product Name:
Model No.:
Power:
Volume:
All-in-One Herb Cooker
EXT2020
74W
350ml
Input power:
100-240V ~ 50/60Hz
Compliance:
xx-xxxx
4
2 A MAX
EN
Part
Material
Standard compliance
Glass
Borosilicate glass
XXXX
SUS304 stainless steel
XXXX
Pipette
Dish Lid
Sleeve
Sensor Pad
Silicone
Lock Ball
Filter Funnel
SUS304 stainless steel
XXXX
Silicone
Brush
SUS304 stainless steel
XXXX
Wool
3. Use
ELECTRICAL SHOCK HAZARD
- Do not use an extension cord.
- Failure to follow these instructions can result in electrical shock, fire, or death.
3.1 Before f irst use
1. Remove all stickers and labels and clean the outside and the inner surface of the cooker with a
damp cloth.
2. Use the cooker for the first time in Decarb function with empty Glass. In this way you will burn
off any dust that has fallen into the cooker during production or transport.
This appliance can be used safely with an input voltage between 110 and 240 V DC
and at both 50 Hz or 60 Hz without making any setting change.
During first use some odour may develop.
User hints & tips
- This cooker is designed with optimal temperatures and time duration for the
decarboxylation and extraction of medicinal herbs. Infusing dried and ground
common kitchen spices with oil may also yield satisfactory outcomes.
3.2 Operation - General
1. If necessary, shorten the cord by wrapping it.
2. Make sure the inner surface of the Main Body and the bottom of the Glass is dry.
3. Place the Main Body on the Base with the Base Mark facing the operator.
4. Plug in the cooker. Wait till the cooker beeps and the Point LED Light is on. The cooker is now
in the initial standby mode ready to use.
It doesn’t matter which function the Base Mark is aligned to when the cooker is
connected to power. You can only activate a chosen function circle by further action
of turning the Rotary Control body.
3.3 Operation - CBD Decarb & Decarb
User hints & tips
- Differently prepared and stored plant material have different moisture content
and will require different lengths of time to reach the optimal temperature.
- Water vapour may condense on and around the Filter Disc during decarboxylation if the plant material is fresh or with high moisture content. In such case, you
can still proceed to Oil functions without drying the plant material or the Glass.
The water will evaporate during the Oil function circles.
For best results:
- Break big plant material into smaller parts before decarboxylation.
1. Put plant material into the Glass, make sure it doesn’t exceed the MAX mark on the Glass.
2. Make sure the Sleeve is positioned in the right place, then cover the Glass with the Dish Lid.
The Glass must be covered properly with the Dish Lid in order to achieve the optimal temperature. If the hot air escapes too fast, the sensor will never detect the
optimal temperature.
5
EN
3. Place the covered Glass securely in the Main Body and make sure the bottom of the Glass
touches the probes.
4. Turn the Rotary Control body, align the chosen Decarb function to the Base Mark.
5. Wait for 3 seconds, you will hear the beep and see the Ring LED Lighting up with pulsation.
Now the chosen Decarb function circle is activated.
6. Once the heating is complete, the pulsating Ring LED will switch off and the cooker enters
cooling phase. You will hear the sound of fan working during this cooling phase. You can now
either remove the Glass from the Main Body and let it cool down at room temperature, or wait
till the cooling phase is complete by the cooker.
7. The cooker goes back to the initial standby mode and beeps once the heating-cooling cycle is
complete.
Pot by NOIDS has carefully designed temperature control with high precision,
which ensures that prolonged decarboxylation does no harm to the bioactive compounds in the plant material. So if any adjustment is needed during heating, simply
turn the cooker to OFF mode, let the Glass cool down to safe temperature and
make the adjustment, then put the Glass back to the Main Body and activate the
desired Decarb function again.
3.4 Operation - CBD Oil & Oil
1. Put liquid oil or cooking butter into the Glass with alread decarboxylated herb. Make sure that
the volume of the total mixture of oil and herb doesn’t exceed the MAX mark on the Glass.
2. Cover the Glass properly with the Dish Lid. Make sure the Glass bottom is dry and the Sleeve is
positioned at the right place.
3. Place the covered Glass securely in the Main Body, make sure the bottom of the Glass touches
the probes.
4. Turn the Rotary Control body, align the chosen Oil function to the Base Mark.
5. Wait for 3 seconds, you will hear beeping sound and see the Ring LED Lights up with pulsation.
Now the Oil function circle is activated.
6. Once the heating is complete, the pulsating Ring LED will switch off and the cooker enters
cooling phase. You will hear the sound of fan working during this cooling phase. You can now
either remove the Glass from the Main Body and let it cool down at room temperature, or wait
till the cooling phase is complete by the cooker.
7. The cooker goes back to the initial standby mode and beeps once the heating-cooling cycle is
complete.
Pot by NOIDS has carefully designed temperature control with high precision,
which ensures that prolonged Oil infusion does no harm to the bioactive compounds in the plant material. So if any adjustment is needed during heating, simply
turn the cooker to OFF mode, let the Glass cool down to safe temperature and
make the adjustment, then put the Glass back to the Main Body and activate the
desired Oil function again.
3.5 Operation - Filter the oil
1. Prepare an oil storage container with an opening larger than the diameter of the Spout.
2. Remove the Dish Lid and apply the Filter Set on the Glass.
3. Hold the Glass while pressing the Support Lid securely to the Glass with one hand. Then, turn
the Glass upside down and press the Finger Grip with the other hand to squeeze the oil out of
the Glass into the container.
User hints & tips
If the herb in the oil is broken into very fine parts, it is advised to apply a piece of
filter mesh to the Spout before step 3:
1. Put a piece of filter mesh on the Spout.
2. Secure the mesh to the Spout with the Lock Ball.
3.6 Operation - Gather the remaining oil
1. Once the oil is Filtered out, remove the Filter Set and add warm water into the Glass till all
the plant material is submerged into the warm water. Shake the Glass gently till all the
remaining oil gathers above the water.
2. Place the Glass on a stable surface and let it rest till the oil forms a clear layer on top of the
warm water.
6
EN
3. Put the Filter Set back in.
4. Attach the Pipette to the Spout with the Lock Ball.
5. Press down the Filter Disc slowly and carefully till the oil enters the Glass Pipette.
6. Close the upper opening of the Pipette with your thumb while removing the Pipette.
7. Release the oil in the Pipette to a container by lifting your thumb.
8. Go back to step 4 till all the remaining oil is gathered.
User hints & tips
If water enters the Pipette by accident, use a piece of kitchen paper to carefully
suck the water out from the lower opening of the Pipette.
3.7 Operation - Evaporation
TOXIC HAZARD
-Do NOT use any non-food-grade ethanol with Evaporation. It may contain
impurities that are highly toxic.
- Use ONLY food-grade, non-denatured ethanol with the Evaporation function.
FIRE HAZARD
High volume/proof ethanol can be highly inflammable.
-Do not use Evaporation function in small and closed space. Make sure the space
is larger than 50 m3 and there is air exchange between indoor and outdoor.
-Keep the Cooker away from open flame during Evaporation, with a
minimum distance of 5 m.
User hints & tips
For best result, use food-grade non-denatured ethanol product with no less than
95% ethanol by volume (≥190 PF).
1. Pour the infused food-grade ethanol into the Glass. Make sure that the volume doesn’t exceed
the MAX mark on the Glass.
2. Cover the Glass with the Dish Lid. Make sure the Glass bottom is dry and the cooker is in the
initial standby mode.
3. Place the covered Glass securely in the Main Body, make sure the bottom of the Glass touches
the probes.
4. Turn the Rotary Control body, align the Evaporation function to the Base Mark.
5. Wait for 3 seconds, you will hear a beeping sound and see the Ring LED Lights up with
pulsation. Now the Evaporation function is activated.
6. If adjustment is needed during this function cycle, simply turn the Rotary Control to the OFF
mode, let the Glass cool down first and then make the adjustment. Once this is done, go back
to step 3 and activate the function again.
7. Turn the Rotary Control Body to the OFF mode after desired amount of ethanol is evaporated.
8. Remove the Glass from the Main Body.
User hints & tips
- The evaporation mode will automatically stop once the temperature of the
content reaches 102°C / 215.6°F. There is no risk of burning the herbal
concentrate with evaporation function.
- The Dish Lid is coated with anti-stick food grade silicon. If the herbal concentrate
sticks to the bottom of the Glass in case of total evaporation of the ethanol,
simply:
1. add a little bit of ethanol back into the concentrate,
2. stir till the concentrate has dissolved into the added ethanol,
3. pour the diluted concentrate out into the Dish Lid,
4. let the added ethanol evaporate in room temperature, and
5. easily remove the concentrate from the non-stick Dish Lid.
4. Cleaning and care
4.1 Instructions
ELECTRICAL SHOCK HAZARD
Always Disconnect the plug from the socket before cleaning the Main Body
of the cooker.
7
EN
4.2 Cleaning the surface
Hot appliance, BURNS HAZARD
Always leave the appliance and the parts to cool down before cleaning.
Improper use, RISK OF DAMAGE TO SURFACES
- Do not use steam jets for cleaning the appliance.
- Do not use cleaning products containing chlorine, ammonia or bleach on steel
parts or parts with metallic finishes
(e.g. anodizing, nickel- or chromium-plating).
- Do not use abrasive or corrosive detergents
(e.g. powder products, stain removers and metallic sponges).
- Do not use rough or abrasive materials or sharp metal scrapers.
To keep the surfaces in good condition, they should be cleaned regularly after use.
4.3 Ordinary daily cleaning
Always use products that do not contain abrasives or chlorine-Based acids. Put the product onto
a damp cloth and wipe the surface, then wipe over thoroughly and dry with a soft cloth or a
microfiber cloth.
4.4 Food stains or residues
Do not use metallic sponges or sharp scrapers as they will damage the surfaces. Use ordinary
non-abrasive products with the aid of wooden or plastic utensils if necessary. Wipe over thoroughly and dry with a soft cloth or a microfiber cloth.
4.5 Cleaning the Glass
The Glass is machine washable.
• Dishwasher: The Glass is machine washable. Rinse first and then put the Glass into dishwasher
- same as washing a regular glass.
• Hand wash: Rinse first with warm water to get rid of residue. Use non-abrasive dish cleaners
and non-abrasive cloth or sponge for further cleaning.
4.6 Cleaning the Filter Set
The Filter Set is machine washable. Before washing, remove the Filter Disc from the Filter Funnel.
• Dishwasher: Rinse first and then put the Filter Set into dishwasher. Make sure the pipe and
pipette are not horizontally placed - same as washing regular kitchen tools.
• Hand wash: Rinse first with warm water to get rid of residue. Use non-abrasive dish cleaners
and non-abrasive cloth or sponge for further cleaning.
5. Troubleshooting
5.1 Before troubleshooting
Make sure the cooker is properly connected to power and the power is on.
5.2 What to do if ...
Beep
Cooker
Light
Cause
No beep No light Damaged power cord.
doesn’t turn on
Solution
Contact NOIDS distributor for
replacement. (Visit www.noids.green)
10 sec.
10 sec.
Blinks
The Glass is not put in the Main
Put the Glass in the Main Body, or
Body or the Glass is not touching
press the Glass down to touch the
the bottom sensors in the Main
probes properly, then restart the
Body properly
function
No light The bottom of the Glass is wet
Dry the bottom of the Glass, then
restart the function
Cooker
No beep
Blinks
doesn’t work
Temperature in the Glass is too
Let the Cooker cool down first, then
high - protection against dry
put content in the Glass and restart
heating
the function
Glass is not properly covered and
Cover the Glass properly and restart
the target temperature can not
the function
be reached
Heating time for evaporation
Restart the function to continue evap-
function is too long
oration
Thermal sensor malfunction
Restart the function by turning the
Rotary Control
30 sec
Blinks
Component defect
Contact NOIDS for repair. (Visit www.
noids.green)
8