UFED Physical Analyzer
User Manual
December 2014
Legal Notices
Copyright © 2014 Cellebrite Mobile Synchronization Ltd. All rights reserved.
This manual is delivered subject to the following conditions and restrictions:
This manual contains proprietary information belonging to Cellebrite Mobile Synchronization Ltd. Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of the
UFED Physical Analyzer.
No part of this content may be used for any other purpose, disclosed to any person or firm, or reproduced by any means, electronic or mechanical, without the express prior written permission of Cellebrite Ltd.
The text and graphics are for the purpose of illustration and reference only. The specifications on which they are based are subject to change without notice.
Information in this document is subject to change without notice. Corporate and individual names and data used in examples herein are fictitious unless otherwise noted.
Contents
Contents
1.1. Overview .................................................................................... 9
1.2. Physical extraction ............................................................. 10
1.3. Data analysis .......................................................................... 12
2.1. Installing UFED Physical Analyzer ............................ 16
2.1.1. System requirements .............................................. 16
2.1.2. Software installation ................................................. 17
2.1.3. Activating UFED Physical Analyzer .................. 25
2.1.4. Moving UFED Physical Analyzer with a software license to another PC ...................................... 32
2.1.5. Enabling connectivity with Windows
Vista ................................................................................................. 35
4
3.1. Starting UFED Physical Analyzer .............................. 37
3.2. Link Analysis demo ........................................................... 38
3.3. Opening an extraction for analysis ......................... 38
3.4. Opening an extraction in advanced mode ....... 41
3.4.1. Advanced opening of a UFED extraction file .................................................................................................... 41
3.4.2. Advanced opening of a non-UFED extraction file ............................................................................ 52
3.4.3. Saving a .ufd file ......................................................... 64
3.5. Saving a project session ................................................ 65
3.6. Loading a project session............................................. 66
3.7. Closing a project ................................................................ 67
3.8. Closing UFED Physical Analyzer ............................... 67
3.9. Keyboard shortcuts .......................................................... 68
4.1. Project tree ............................................................................ 70
4.1.1. Working in the project tree area ...................... 82
4.2. Data display area................................................................ 83
Contents
4.2.1. Welcome tab ................................................................ 85
4.2.2. Extraction summary tab ......................................... 87
4.2.3. Data tabs ......................................................................... 89
5.1. Searching for information in a data tab ............ 111
5.2. Using the quick filter ..................................................... 111
5.3. Using the advanced filter ........................................... 114
5.4. Searching for information in all open projects ........................................................................................... 115
5.5. Browsing the file system ............................................. 116
5.6. Timeline view ..................................................................... 117
5.7. Accessing conversation view................................... 120
5.8. Working with watch lists ............................................ 123
5.8.1. Creating a watch list .............................................. 123
5.8.2. Editing a watch list ................................................. 127
5.8.3. Importing a watch list .......................................... 128
5.8.4. Exporting a watch list ........................................... 130
5
5.8.5. Deleting a watch list .............................................. 131
5.8.6. Running a watch list .............................................. 132
5.8.7. Locating a watch list ............................................. 134
5.9. Bookmarking information (entity bookmarks) .................................................................................. 134
5.9.1. Creating a new entity bookmark ................... 135
5.9.2. Editing an entity bookmark .............................. 136
5.9.3. Deleting an entity bookmark ........................... 137
5.10. Device Locations ........................................................... 137
5.10.1. About location data ............................................ 137
5.10.2. Viewing location data on BING .................... 140
5.10.3. Markers and information windows ........... 143
5.10.4. Retrieving addresses .......................................... 144
6.1. Using the feature ............................................................. 148
6.2. Updating your license with the selected languages ..................................................................................... 148
6.2.1. Selecting languages in MyCellebrite .......... 148
6.2.2. Downloading the translation pack .............. 154
6
6.2.3. Translating the decoded data ......................... 156
6.2.4. Reporting ..................................................................... 158
8.1. Updating the signature database (online) ...... 164
8.2. Updating the signature database from file
(offline) ............................................................................................ 166
10.1. Extraction from iOS devices ................................... 183
10.1.1. Prerequisites ............................................................ 183
10.1.2. Performing physical extraction .................... 184
10.1.3. Performing advanced logical extraction 199
10.2. Extraction from GPS or mass storage devices ............................................................................................ 210
10.2.1. Reading data from a GPS or mass storage device ....................................................................... 213
11.1. Working with TomTom ............................................. 217
11.1.1. Exporting a TomTom file ................................. 218
11.1.2. Importing a TomTom file ................................ 219
11.2. Carving images .............................................................. 220
11.2.1. Scanning for carved images .......................... 221
11.2.2. Working with carved images ........................ 224
11.3. Verifying hash values .................................................. 224
12.1. Searching for information in the Hex data and decoded data ................................................................... 230
12.1.1. Searching strings .................................................. 232
12.1.2. Searching bytes ..................................................... 237
12.1.3. Searching dates ..................................................... 241
12.1.4. Searching SIM ICCID numbers ..................... 246
12.1.5. Searching SMS numbers .................................. 251
Contents
12.1.6. Searching for regular expressions
(GREP).......................................................................................... 255
12.1.7. Searching SMS text strings ............................. 260
12.1.8. Searching for patterns ....................................... 265
12.1.9. Searching for codes and passwords ......... 270
12.2. Browsing the hex extraction ................................. 274
12.3. Using an offset to jump to a different location in the file .................................................................... 275
12.4. Working with bookmarks ........................................ 276
12.4.1. Adding a bookmark ............................................ 276
12.4.2. Editing a bookmark ............................................. 279
12.4.3. Deleting a bookmark ......................................... 279
12.5. Decoding raw data ...................................................... 279
12.6. Viewing the hex data information ..................... 280
12.7. Locating specific data types in the Hex .......... 282
7
14.1. Managing chains .......................................................... 287
14.1.1. Constructing a new chain ............................... 289
14.1.2. Editing an existing chain ................................. 291
14.1.3. Managing device chains .................................. 294
14.1.4. Removing a chain ................................................ 300
14.1.5. Chain descriptions ............................................... 300
14.2. Plug-ins ............................................................................... 304
14.2.1. Managing plug-ins .............................................. 304
14.2.2. Running a specific plug-in .............................. 306
14.3. Using the Python Shell .............................................. 308
14.4. Exporting the file system ......................................... 309
14.5. Using the Android unlock pattern carver plug-in ............................................................................................. 309
14.6. Android unlock password carver plug-in ...... 310
15.1. General settings ............................................................. 312
15.2. Data files ............................................................................. 315
15.2.1. Data files filtering methods ............................ 316
8
15.2.2. Managing data files settings ......................... 317
15.3. Hex viewer settings ..................................................... 320
15.4. Models settings ............................................................. 322
15.5. Additional report fields ............................................. 323
15.5.1. Adding a new report field ............................... 324
15.5.2. Editing a report field ........................................... 326
15.5.3. Deleting a report field ....................................... 326
15.6. Report defaults ............................................................... 326
15.7. Post-chain plugin settings ...................................... 335
15.8. Saving settings ............................................................... 336
15.9. Loading settings ........................................................... 337
15.10. Setting project settings.......................................... 337
15.10.1. Setting a unified time zone for the project ........................................................................................ 337
15.10.2. Setting the case information ...................... 341
16.1. File menu ........................................................................... 345
16.2. View menu ........................................................................ 346
16.2.1. Viewing the trace window ............................. 346
16.3. Tools menu ....................................................................... 348
16.4. Extract menu ................................................................... 349
16.5. Python menu .................................................................. 349
16.6. Plug-ins menu ................................................................ 350
16.7. Report menu ................................................................... 350
16.8. Help menu ........................................................................ 351
Chapter 1: Introduction
Chapter 1: Introduction
1.1. Overview
UFED is made up of three components:
The UFED Touch or UFED unit enables logical, password, SIM, file system, and physical extractions from mobile devices, which can then be saved to a USB flash drive, SD memory card, or directly to your PC.
UFED Physical Analyzer application provides an in-depth view of the device's memory using advanced decoding, analysis, and reports. UFED Physical Analyzer can decode all types of extractions created by the UFED Touch or UFED Classic unit.
Phone Detective application helps investigators quickly identify a mobile phone by its physical attributes, eliminating the need to start the device and the risk of device lock
The UFED work flow consists of two steps:
Extraction - Physical, file system, logical, password, SIM card extraction using the UFED Touch or
UFED unit
Decoding, analysis, and reporting using the UFED Physical Analyzer
9
10
1.2. Physical extraction
When performing a physical extraction, UFED uses advanced extraction methods to create a single
Hex extraction file for each flash memory chip, or address range utilized by the mobile device. Unlike g is captured into Hex extraction file(s) that are later read and decoded using UFED Physical Analyzer.
The created physical extraction includes memory spac contain deleted data such as SMS, call logs, phonebook entries, pictures, videos, and user passwords.
Physical extraction provides a bit-by-bit copy of the entire flash memory of a mobile device. Decoding of physical extractions not only enables the acquisition of intact data, but also data that is hidden or has been deleted. Deleted data can be recovered from files and unallocated space
1
.
UFED Physical Analyzer provides advanced carving algorithms, by recovering SQLite records to reveal additional deleted data from unallocated space. The amount of deleted data varies depending on the data on the device. The decoded data is displayed in the same lists as the analyzed data. For example, deleted SMSs from unallocated space are displayed in the same list as the SMSs.
1
Unallocated space is clusters of a media partition that is not in use for storing active files. It may contain pieces of files that were deleted from the file partition but not removed from the physical disk.
Chapter 1: Introduction
Data carving from unallocated space provides the following benefits:
11
Best and quickest solution for uncovering deleted data on the market.
Additional deleted data in less time.
Reveals deleted data that was not available previously.
Higher quality data due to the fact that both false positives and duplicates are automatically removed.
Automatic activation: There is no need for manual activation.
Various content types supported such as: SMSs, MMSs, Calls, Contacts, Emails, and application data
2
.
Same view: Ability to arrange all data, including data decoded from unallocated space, in the same views and with timelines.
2
Application data such as: Kik, WhatsApp, Facebook, Facebook Messenger, Twitter etc.
12
1.3. Data analysis
UFED Physical Analyzer enables the investigator to perform in-depth analysis of the extracted data and generate reports.
UFED Physical Analyzer has the following key features:
Decoding of the extraction with a layered view of memory content
Provides a detailed view of the Hex file
Reconstructs the device file system
Decode various Analyzed data types such as: Contact lists, SMS messages, call logs, device information (IMSI, ICCID, user codes), application information, and more
Provides a view of data files images, videos, databases, and so on
Provides access to both current and deleted data
Reveals device passwords (when applicable)
Powerful extraction for iOS and GPS devices
Provides intuitive and user friendly UI for browsing the extracted information
Powerful analysis and search tools
Instant search for all project content
Advanced search based on multiple parameters
Instant search for data tables content
Watch list for highlighting information based on a predefined list of values
Chapter 1: Introduction
Time line for viewing all the events performed via the mobile device in a single chronological view
Project analytics providing comprehensive activity analysis
Malware scanner to identify malware in the device
Ability to search the Hex by various parameters such as strings, bytes, numbers, dates
Ability to use regular expression search (RegEx) to look for specific data strings
13
Ability to bookmark memory locations for indexing of key areas for later review
Ability to use Python shell commands for data analysis
Plug-ins
Add or remove plug-ins
Write your own plug-ins using Python scripting language
Manage chains
Reports
Generate reports in various formats
Report customizing and personalizing (logo, header, etc.)
14
Chapter 2: Installation and activation
Chapter 2: Installation and activation
This chapter describes the installation and activation process of UFED Physical Analyzer on your PC.
15
16
2.1. Installing UFED Physical Analyzer
2.1.1. System requirements
PC
Operating System
Memory (RAM)
Space requirements
Additional requirements
Windows compatible PC with a Pentium® IV or compatible processor running at 1.6 GHz or higher
Microsoft Windows XP
3
with SP3 or later
OS
32 bit
64 bit
Recommended
4GB
8GB
Minimum
4GB
4GB
500 MB of free disk space for installation
Microsoft® .Net version 4.0
NOTE: Windows XP 64 bit requires installation of a .Net 2.0 hotfix
(NDP20-KB913384-X64.exe) from http://archive.msdn.microsoft.com/KB913384/Release/ProjectRele ases.aspx?ReleaseId=771
3
By February 28, 2015, the UFED Series will no longer support Windows XP.
Chapter 2: Installation and activation
Permissions
If you intend to activate the application using a hardware license key (dongle) provided by Cellebrite, you must have administrative rights over the computer.
17
NOTE: To enable extraction to a PC with Windows Vista Operating System, follow the procedure in
(page
).
2.1.2. Software installation
2.1.2.1. Obtaining a copy of UFED Physical Analyzer
A copy of the latest UFED Physical Analyzer application installer can be obtained from the following sources:
The UFED Physical Analyzer CD.
Downloaded from the MyCellebrite site.
Downloaded from the link provided in the release notes.
18
2.1.2.2. Installing UFED Physical Analyzer
NOTE: Before you begin, ensure that cable U-441 is not attached to your computer.
1) Double-click the setup file.
2) Select the desired language and click OK to continue.
Chapter 2: Installation and activation
3) Click Next.
19
20
4) Select I accept the agreement, and click Next.
Chapter 2: Installation and activation
5) If desired, click Browse and set a different installation folder.
6) Click Next.
21
22
7) If you do not want a desktop icon, clear the Create a desktop icon checkbox.
8) Click Next.
Chapter 2: Installation and activation
9) Click Install.
The installation begins.
23
24
NOTE: As part of the installation process, you may be prompted to download and install Microsoft
.NET 3.5 Framework. This is part of the installation and requires that your computer has
Internet access.
Chapter 2: Installation and activation
10) Select Yes, restart the computer now and click Finish.
Your computer restarts and UFED Physical Analyzer is installed.
2.1.3. Activating UFED Physical Analyzer
Activate UFED Physical Analyzer in one of the following ways:
Using a license dongle
Using a software license
Using a network dongle
NOTE: Check your UFED kit to make sure which method you should use.
2.1.3.1. New version notification
Cellebrite will inform you when a newer version of your software is available. If you are connected to the internet you will receive this notification when the new version is available. If you are not connected to the internet the notification will appear every 3 months.
25
26
2.1.3.2. Using a license dongle
Use the UFED dongle provided with your UFED kit. The dongle contains licenses for all the applications purchased.
To use UFED Physical Analyzer with a dongle:
UFED Dongle
1) Connect the dongle to a USB port on your computer. The license is automatically located. When the dongle is recognized by the operating system, the application can read the license.
2) Start UFED Physical Analyzer.
Congratulations, your application is now ready!
If a license dongle is not found:
1) When starting for the first time, or when a license dongle is not found, the Cellebrite Product
Licensing window appears.
Chapter 2: Installation and activation
2) If you connected the dongle to a USB port on your computer, and it still does not work, contact [email protected]
.
NOTE: The HASP dongle drivers must be installed in order to use a hardware license key. If the drivers were not installed during the UFED software installation process, you can run the installation process again and select Install Hasp Dongle Drivers at the end of the process.
27
28
2.1.3.3. Using the application with a software license
The first time you open the application, you must activate the license.
To use UFED Physical Analyzer with a software license:
1) Go to the following link: https://my.cellebrite.com/physicalanalyzer
2) Sign into your MyCellebrite account.
(If you don't have an account, click Register now, create a user, and then go back to the required
UFED application link.)
You will be directed to the product activation window.
3) Click to download the application and save the file to a PC.
4) Extract the zip file, click the installation file and install the software using the Setup Wizard. Restart the PC if required.
5) Repeat step 1 to go to the application link.
6) In the Activation method box, if you purchased UFED 4PC, select Activation code or if you purchased UFED Touch, select UFED Touch/UFED Classic.
7) Depending on the product you purchased, continue as follows:
Activation Code
Chapter 2: Installation and activation
UFED 4PC: In the Activation Code field, enter the Activation code provided with the
UFED 4PC kit.
29
UFED Touch: In the Choose Serial Number field, select the UFED serial number displayed on the UFED Touch unit or UFED Touch License Activation screen.
8) Next obtain your Computer ID (do not close the MyCellebrite page while performing this step).
Start the application. The Cellebrite Product Licensing window appears.
Click Copy to copy the Computer ID displayed in the window.
9) In MyCellebrite paste the copied Computer ID.
10) Click Download Now! to download your application license key to your PC. The license key will also be sent to your registered MyCellebrite email address.
11) In the application, click Load license file in the Cellebrite Product Licensing window.
30
12) Select the License file and click Open. A message appears to indicate that the software license was updated successfully.
13) Click Close.
Congratulations, your application is now ready!
2.1.3.4. Using a network dongle
contains licenses for all the applications purchased.
To use UFED Physical Analyzer with a network dongle:
UFED Network Dongles
1) Start the UFED application. If the network dongle is connected to the network, the application starts and the user can start working immediately.
If the network dongle is not recognized, the Cellebrite Product Licensing window appears.
Chapter 2: Installation and activation
2) Click Network. The following window appears.
31
32
NOTE: If a dongle was not found on the network make sure that you have an Internet connection and that a dongle is connected to the network. Then click Refresh to search for a network dongle again.
NOTE: By default the network configuration is set to Broadcast. If required, you can manually connect to the network dongle. Click Configure to change the network configuration to
Specific host. Enter the host name (or IP address) and the port number (1 5 digits).
NOTE: If there is only one network dongle it will be selected automatically. If there are multiple network dongles, select the required dongle from the list and click Apply.
Congratulations, your application is now ready!
2.1.4. Moving UFED Physical Analyzer with a software license to
another PC
In cases where a UFED Physical Analyzer installation that has been activated by a software license needs to be moved to another PC, you must first deactivate (remove) the license from the computer.
The deactivation process varies between different license versions; follow the instructions in your application.
Chapter 2: Installation and activation
2.1.4.1. Deactivating version 2 licenses
1) In UFED Physical Analyzer, go to Help > Show License Details.
The Cellebrite Product Licensing window appears.
2) Click Deactivate software license.
The Software License Deactivation window appears.
3) Click Generate deactivation file.
UFED Physical Analyzer is deactivated.
4) To get your new UFED Physical Analyzer license, go to http://my.cellebrite.com/physicalanalyzer, and follow the license activation steps. For more
information, see
(page
).
33
2.1.4.2. Deactivating version 5 licenses
1) In UFED Physical Analyzer, go to Help > Show License Details.
The Software License Deactivation window appears.
2) Click Deactivate software license.
The Software License Deactivation window appears.
3) Click Copy to copy the computer ID.
4) Go to http://my.cellebrite.com/deactivation, and log in to your MyCellebrite account.
34
If you do not have an account, click Register now and create a user. Then go back to http://my.cellebrite.com/deactivation.
You are directed to the Deactivation wizard.
5) Paste the copied computer ID, and click Next.
6) Click Download and download the deactivation file to the PC.
7) In UFED Physical Analyzer, go to Help > Show License Details.
8) Click Select Deactivation File, and select the deactivation file downloaded in step 6.
Your license is deactivated and UFED Physical Analyzer creates a deactivation file. The Software
License Deactivation window informs you that the deactivation file has been created.
9) Return to the Deactivation wizard in MyCellebrite.
10) Click Choose File, and upload the deactivation file created by UFED Physical Analyzer.
11) Click Finish.
12) To get your new UFED Physical Analyzer license, go to http://my.cellebrite.com/physicalanalyzer, and follow the license activation steps. For more
information, see
(page
).
Chapter 2: Installation and activation
2.1.5. Enabling connectivity with Windows Vista
Perform the following procedure to enable the UFED unit to connect to PCs running the Windows
Vista operating system.
1) Go to the Cellebrite Physical Analyzer Drivers\cbrtucbl folder.
2) Double-click USB_Cable_DRV.exe.
3) Follow the on-screen instructions.
35
36
Chapter 3: Getting started
Chapter 3: Getting started
UFED Physical Analyzer provides powerful decoding and analysis tools for the extracted device data, assists you in the complex tasks of intelligence gathering, investigative research, and providing legal evidence in the form of reports.
37
Hex extraction, file system and analyzed data in a clear and concise way, allowing investigators to use powerful search tools to reveal relevant information.
As a completing step, the application enables you to generate reports of your findings in various file formats, such as HTML, PDF, Excel (*.xlsx), and XML.
3.1. Starting UFED Physical Analyzer
To start UFED Physical Analyzer, do one of the following:
Double-click the UFED Physical Analyzer desktop shortcut.
Select Start > Programs > Cellebrite Mobile Synchronization > UFED Physical Analyzer .
For an overview of the workspace, see
(page
).
38
3.2. Link Analysis demo
When you open UFED Physical Analyzer you will be presented with the option to view a sample project in UFED Link Analysis.
The UFED Link Analysis demonstration contains preloaded sample content. It consists of 3 reports which have samples of images, SMSs, MMSs and many other pieces of information. The 3 loaded
Persons are linked to each other in various ways.
The demonstration has set some Person details, data filters, opened the map tab and created a timeline. All of these are created to show a simple Link Analysis project.
3.3. Opening an extraction for analysis
UFED Physical Analyzer can open files created by the UFED device, XML files created by the UFED
Physical Analyzer, UFDR files, UFD files and URP files (these files were created in the UFED Report
Manager application). In Advanced mode, UFED Physical Analyzer can open image files. For more
information, see
(page
).
1) If the device data was extracted to a removable drive, connect the USB flash drive or SD card containing the extracted data to your PC.
NOTE: For faster processing, copy the extraction folder from the removable media to the PC.
Chapter 3: Getting started
2) Do one of the following:
In the Welcome tab, click Open.
Drag-and-drop the UFD file into UFED Physical Analyzer.
From the application toolbar, click .
From the application menu, select File > Open.
39
3) Browse to the location of the extracted device data folder and open it.
40
4) Select an extraction in one of the supported file formats:
UFED dump (*.ufd) file
Binary files (*.bin). Raw binary files or any Hex extraction generated by another
application using the advanced opening feature. See
(page
).
Nokia PM (*.pm)
Blackberry backup file (*.ipd)
Blackberry backup file (*.bbb)
Sony Ericsson GDFS (*.gdfs, *.bin)
TomTom CFG (*.cfg)
UFED report (*.xml) - Logical reports generated by the UFED unit and XML reports created by the UFED Physical Analyzer
UFED Report Manager (*.urp, *.ucp) - UFED Report Pack/UFED Content Pack reports created by Report Manager
UFED Report Package (*.ufdr)
NOTE: By default, the Open dialog box is set to display the *ufd file which is the information mapping file of the extracted device data.
5) Click Open.
The data analysis process (including project analytics) begins and can run for several minutes. At the end of the process, a new project is added to the project tree, and the Extraction summary appears in the data display area.
Chapter 3: Getting started 41
NOTE: To open an extraction quickly when UFED Physical Analyzer is closed, double-click the *.ufd file in the extraction directory. UFED Physical Analyzer opens and begins the data analysis.
3.4. Opening an extraction in advanced mode
The Open (Advanced) feature enables you to specify the device data extraction and decoding options.
Select from two main project opening methods:
Select a UFED extraction - Enables you to specify how to decode a UFED extraction file (*.ufd).
Start without a .ufd file - Enables you to start to decode a physical extraction or a file system that was not generated by a UFED unit.
3.4.1. Advanced opening of a UFED extraction file
The standard open process activates a decoding process set according to the device and manufacturer information logged in the *.ufd file.
Using the Select a UFED extraction method enables you to skip the standard Open process, and specify a custom parsing process, or specify how to parse unknown devices.
42
To create a new project from UFED extracted data using Open (Advanced):
1) Select File > Open (Advanced) or click .
The Open (Advanced) dialog appears, enabling you to set the process of decoding the extracted data for your new project.
Chapter 3: Getting started
2) Click Select a UFED extraction.
3) In the Open dialog, select the *.ufd file to be processed and click OK.
The dialog contents changes to Advanced Customization and displays the following information detected based on the chosen *.ufd file:
Device - The manufacturer name and model of the device.
Selected Chain - The standard device decoding chain automatically assigned to the device.
Binary Dumps - The binary extractions images referenced by the *.ufd file.
43
44
4) Customize the file open options as described in the following sections.
5) Click Finish.
3.4.1.1. Specifying a different device
You can specify an entirely different decoding process for the extraction by replacing the selected device.
1) Click Switch Device.
Chapter 3: Getting started
2) From the Select Device list, select the desired device.
3) To filter the displayed devices, do one of the following:
Click on device manufacturer in the list of manufacturers on the left pane
Enter the device manufacturer or model in the Quick Filter field to filter the displayed devices
4) Click Next to return to the Advanced Customization panel.
45
3.4.1.2. Changing the decoding chain
A chain is a set of plug-ins grouped together in a certain order, which is used to decode the extracted data. Each device in the supported devices list of the application has a predefined decoding chain assigned to it.
NOTE: Beside plug-ins, a chain can also include other chains, a simpler way to use a predefined set of plug-ins within another chain.
For more information about decoding chains and plug-ins, see
(page
) and
(page
).
46
To select a different chain:
1) Click Switch Chain.
The Switch Chain dialog opens and displays the default chain assigned to the device.
Chapter 3: Getting started
NOTE: A device can have several assigned chains, but only one of them can be set as the default chain.
47
2) From the chains list, select the desired chain in one of the following ways:
Select the manufacturer name under the Current Device section to display the chains assigned to devices of the same manufacturer.
Under the Chains section of the list:
Select My Chains to select from the list of custom chins you constructed.
Select All Chains to select from the list of all predefined device chains.
Use the Quick Filter field to filter the displayed list items.
3) Select the relevant chain, and click Select to return to the Advanced Customization panel.
The default chain is replaced by the selected chain.
To edit the current chain:
1) Click Edit.
48
The chain structure dialog of the current chain opens and displays the chain.
Chapter 3: Getting started
2) To add a component to the chain: a) Click Add Chain/Plugin. b) From the Component Library, select one of the following:
49
Device: The entire chain of a specific device.
Chain: A specific predefined chain.
Plugin: A specific plug-in.
50
NOTE: Items selected under both Device and Chain are added to the chain as a Chain component.
3) Click to add the component.
4) To remove a component from the chain list, click the x at the right of the component item, then click Yes to approve.
5) Click OK to return to the Advanced Customization panel.
The default chain is replaced by the customized chain.
To save a customized chain:
After you customize a chain, you can save the changes made to the chain for future use using the
Save As or Save buttons in the Selected Chain section.
NOTE: The Save button is available only for customizations for unlocked user-defined chains saved in
My Chains. For more information about user defined chains, see
(page
).
1) Click Save to replace the user-defined chain with the current one or Save As to save the current chain as a new chain.
2) If you clicked Save As, enter a name for the new chain and click Save.
Chapter 3: Getting started
The new chain is added to the My Chains list of customized chains of the application, and the saved chain appears as the Selected Chain.
3.4.1.3. Adding a binary dump
You can add more binary dump files received from a different source.
To add a binary dump file, click or Add Binary Dump in the Binary
Dumps area, and select the binary extraction file you wish to add. Each binary dump you add is shown as a separate component in the Binary Dumps section of the dialog.
To remove a binary dump, click that appears when you position the mouse over it.
51
52
3.4.1.4. Adding a file system dump
You can add a file system dump to the project received either as a ZIP archive or as a folder containing the file system extraction files.
To add a file system extraction, click either Zip File or Folder, and select the ZIP archive or folder you wish to add.
NOTE: You can add one file system extraction only. Trying to add more than one removes the previously added file system dump,
To remove a file system extraction, click that appears when you position the mouse over it.
3.4.2. Advanced opening of a non-UFED extraction file
When you receive binary or file system extractions that were not generated by a UFED unit, or you how to decode them for the new project.
1) Select File > Open (Advanced) or click .
Chapter 3: Getting started
The Open (Advanced) dialog appears, enabling you to set the process of decoding the extracted data for your new project.
53
2) The Start without a UFD file option provides you with two starting points for your new project:
54
Select Device - Select the specific device definition to use to decode the data extraction.
This option is useful when the device manufacturer and model are known to you. See
(page
).
Blank Project - Provides you with an empty Advanced Customization panel to set your process parameters and data. This option is useful when you have no information about the device and/or manufacturer, and would like to construct a custom decoding process.
See
(page
).
3.4.2.1. Starting with device selection
Create a new project for data extraction based on a known device.
1) In the Open (Advanced) window, click Select Device.
Chapter 3: Getting started
2) From the Select Device list, select the desired device.
3) Use the list of manufacturers on the left to filter the displayed devices by manufacturer, and the
Quick Filter field to filter the displayed devices by any string.
4) Click Next.
55
56
The Advanced Customization panel displays the name and default decoding chain of the selected device.
To select a different device, see
To add binary extractions, see
To select a different parsing chain, see
To customize the parsing chain, see
To add a file system extraction, see
(page
(page
(page
).
).
(page
(page
).
).
).
5) Click Finish.
3.4.2.2. Starting from a blank project
1) In the Open (Advanced) window, click Blank project.
Chapter 3: Getting started
2) To select a device, see
(page
).
3) To select a parsing chain, see
(page
).
4) To customize the parsing chain, see
(page
).
57
58
5) To add binary extractions, see
(page
).
6) To add a file system extraction, see
(page
).
7) Click Finish.
3.4.2.3. JTAG extractions
JTAG (Joint Test Action Group) is an advanced method of data extraction that requires a forensic examiner to connect to the test access ports of the device to obtain a full physical image. This enables the examiner to unlock and gain access to the raw data stored on the memory chip.
JTAG is non-destructive and offers the opportunity to access data from devices that have been altered or damaged in some, where data ports are unavailable (or disconnected), or it is otherwise impossible to unlock the device using other forensic tools.
UFED Physical Analyzer automates the JTAG decoding process and saves you time in that you no longer need to manually decode the large volume of raw data found in JTAG extractions. The following table displays a sample list of some of the supported devices:
Chapter 3: Getting started
Vendor
Casio
HTC
Huawei
Kyocera CDMA
LG CDMA
Nokia
Pantech
Samsung GSM
Sanyo CDMA
T-Mobile
ZTE GSM
Model
C711 GzOne Boulder
C751 GzOne Ravine
A7272 Desire Z
Google Nexus One
M860 Ascend
Ascend Y300 (Android)
S2100
S2300 Torino (CommonCents)
LX-290
VS-740 Ally
Lumia 520
Lumia 920
Razzle TXT8030VW (Verizon Wireless)
Renue P6030
SGH-i337 Galaxy S4
SGH-i437 Galaxy Express
SCP-2700 Juno
Touch Pro 2
Z221
59
60
For an updated list of devices that support JTAG extractions, refer to the UFED Phone Detective
Mobile App or http://www.cellebrite.com/mobile-forensics/support/ufed-supported-devices .
Once you have the physical memory that was acquired with this method, you can load it into the
UFED Physical Analyzer for decoding. When loading the appropriate UFED JTAG chain, you will receive all the data, as if it was a regular extraction. inside the extraction. Spares are the technical term for metadata of blocks inside the extraction. They can be located in several locations inside the extraction. In regular extractions, they are located at the end of each block. In JTAG extractions they are located at the end of the extraction.
To decode the data extraction using JTAG:
1) In the Open (Advanced) window, click Select Device.
2) To filter the displayed devices, enter the device manufacturer or model in the Quick Filter field, or click on device manufacturer in the list of manufacturers on the left pane.
Chapter 3: Getting started
NOTE: to select a generic JTAG device.
3) Select the required device and click Next.
The following window is displayed.
61
62
4) Select the decoding method and click Next. The available methods change from device to device.
The following window appears.
Chapter 3: Getting started 63
5) To add a binary dump file, click or Add Binary Dump in the Binary Dumps area, and select the binary extraction file you wish to add. Each binary dump you add is shown as a separate component in the Binary Dumps section of the dialog.
6) Click Finish.
64
3.4.3. Saving a .ufd file
At any point of setting the Open (Advanced) parameters, you can click Save UFD at the top right corner of the dialog to save a *.ufd file that logs the selected binary extractions and device information for future use.
The next time you need to decode that file, you can use the saved UFD file to open it with Open or
Open (Advanced).
Chapter 3: Getting started
3.5. Saving a project session
Save the project session to save your work on the project, enabling you to close UFED Physical
Analyzer and restart your session at a later time.
The saved session file (.pas) includes:
User selection in the Analyzed Data and Data Files tables
Hex bookmarks
Entity bookmarks
Watch list results
Opened tabs
Generated reports
A project session can also be created for extractions performed by third party tools.
65
66
NOTE: Saved project sessions do not contain defined settings. For more information on how to save
your settings, see
(page
).
To save a project session:
1) In the File menu, select Save Project Session.
The Save As dialog box appears.
2) Browse to the location where you want to save the project session file.
3) To change the file name, edit the automatically assigned name in the File name box.
NOTE: To overwrite an earlier session, choose the same file name.
4) Click Save.
3.6. Loading a project session
1) From the Welcome tab, open the project that you want to work in.
2) In the File menu, select Load Project Session.
3) In the Open dialog box, browse to and select the project session file that you want to open.
4) Click Open.
The session opens.
Chapter 3: Getting started
3.7. Closing a project
Do one of the following:
In the File menu, select Close.
Right-click the project name and select Close.
3.8. Closing UFED Physical Analyzer
In the File menu, select Exit.
67
68
3.9. Keyboard shortcuts
Ctrl+O
Ctrl+W
Ctrl+P
Ctrl+Shift+O
Ctrl+I
Ctrl+T
Space
Ctrl+R
Ctrl+Tab
Ctrl+Home
Ctrl+End
Ctrl+B
Ctrl+J
Ctrl+U
Ctrl+D
Open a file
Close a project
Open project settings
Open advanced
Open iOS wizard
Open settings
Select or clear check boxes
Open the report wizard
Switch between open tabs
Move the cursor to the beginning of a table
Moves the cursor to the end of a table
Add an entity bookmark
Extract GPS or mass storage device
Open the UFED Downloader to connect to UFED
Select a folder for the dump file system
Chapter 4: Orientation to the workspace
Chapter 4: Orientation to the workspace
69
The workspace contains two main areas; the project tree and the data display area to streamline your workflow.
70
The workspace contains the following components:
1) Application menu bar
2) Application toolbar
3) Project tree
4) Data display area
5) All projects search
4.1. Project tree
The Project Tree area displays the following extracted information structure of each project opened for analysis:
Tree item
Extraction
Summary
Description
Double-click Extraction Summary to open a summary of the project in the data display area.
For more information, see
(page
).
Chapter 4: Orientation to the workspace
Tree item
Device Info
Images
71
Description
Double-click Device Info to open a tab in the data display area.
The Device Info tab provides a list of existing information, as well as important identifiers for the device, such as SIM card and user lock codes, where supported. The number of categories and amount of displayed information depends on the device model and manufacturer.
Double-click an image item to display it in a Hex View tab in the data display area.
The Images tree item lists all the extraction files generated from the memory modules of the device.
72
Tree item
Memory Ranges
Description
The Memory Ranges tree item lists the analyzed memory ranges for each of the extracted memory module of the device
(listed under Images).
Select a memory range to:
Highlight the memory range portion in the displayed data
Add it to the highlights list of the displayed binary image it belongs to (located at the bottom of the
Hex view tab).
Double-click a memory range item to display its content in a new Hex view tab.
Chapter 4: Orientation to the workspace
Tree item Description
File Systems The File Systems tree item lists all the file systems found or reconstructed out of the analyzed binary file.
Each file system is marked with (hard drive).
Deleted files are marked with (red cross).
Double-click any file system item to display its content in a new Hex view tab.
73
74
Tree item
Analyzed data
Description
The Analyzed Data tree item displays groups of analyzed data that are related to device-specific features such as contacts,
SMS messages, call logs, and so on.
The available information and what is displayed depends on the device features and application version. For example, SMS messages are sorted according to the folders used by the messaging feature of the device, such as Drafts, Inbox, Outbox,
Sent, and so on. Email messages are sorted according to the account through which they were sent or received. An uncategorized account or messages folder lists the folders or messages that cannot be categorized in any of the found accounts or account folders (Inbox, Outbox, Drafts, and so on).
The following information types may be displayed in Analyzed
Data:
Personal information - Calendar, contacts, notes, call log, user dictionaries, user accounts
Messaging items - SMS, MMS, email, instant messages, chat
Chapter 4: Orientation to the workspace
Tree item Description
Web browser items - Bookmarks, history, cookies
GPS information - Locations (including from video files, metadata, and SQLite databases), journeys, fixes. For more
information on geolocations, see
(page
).
Device information - Bluetooth pairings, wireless networks,
SIM data, application usage, Wi-Fi, cellular locations
The number in parenthesis designates the number of items each category contains.
Selecting any analyzed data category automatically adds it to the highlights list of the displayed binary image and/or memory range it belongs to (located at the bottom of the Hex view tab), and highlights its data range portions in the displayed data.
75
Data files The Data Files tree item sorts the extracted data into common or known file formats, used by devices and computers, such as images, videos, audio, text, or document files.
76
Tree item Description
In the project tree, the information is displayed in the following categories:
Images - Files that were recognized as image file formats
Videos - Files that were recognized as video file formats
Audio - Files that were recognized as audio file formats
Text - Files that were recognized as text file formats
Databases - Data structures that were recognized as databases
Configurations - Device configuration files (such as iOS plist files)
Applications - Files that were recognized as application files (such as .apk, .jar, .dex, .so, .exe files etc.)
Documents - Files that were recognized as document file formats (such as .doc, .docx, pdf; xlsx, ppt files etc.)
Deleted items are marked with (red cross).
Chapter 4: Orientation to the workspace
Tree item Description
You can create additional data file groups. For more
information, see
(page
).
77
Carving
Tags
The Carving tree item enables you to search the physical extraction for partially deleted or corrupted images.
Double-click Carving to start the search.
For more information, see
(page
).
Certain file types are identified and tagged in the extracted data.
There are eight default tags: Applications, Audio,
Configurations, Databases, Documents, Images, Text, and
Videos.
You can use plug-ins or the Python shell to look for additional data segments and tag them with one of the existing tags, or with a custom tag.
Deleted items are marked with (red cross).
78
Tree item
Timeline
Watch lists
Description
Double-click Timeline to open the device events organized by time in the data display area.
The Timeline tab displays the device's time stamped events, such as calls, SMS, MMS, and so on, in chronological order.
Watch lists are lists of keywords that you create and then use to search and identify events and items of interest in the extracted data.
Expand Watch Lists to view a list of watch lists that have been run in the current session.
Double-click on Watch Lists to view the highlighted entity based on the watch lists.
For more information, see
(page
).
Chapter 4: Orientation to the workspace
Tree item Description
Bookmarks The bookmarks that you create to define and save specific locations in the Hex data are managed in the Bookmarks tree item.
Double-click Bookmarks to open a bookmarks list in a tab in the data display area.
79
80
Tree item
Entity bookmarks
Description
The entity bookmarks you create are managed in the Entity
Bookmarks item of the project tree. The number of entity bookmarks in the project is shown in brackets next to the section name.
Double-click Entity Bookmarks to list the entity bookmarks in a tab in the data display area.
Double-click any entity bookmark to go to the bookmarked item in the appropriate display tab.
For example, double-click an entity bookmark to an SMS message to open the list of SMS messages in an Analyzed Data display tab, with the bookmarked item highlighted.
For more information, see
(page
).
Chapter 4: Orientation to the workspace
Tree item Description
Reports
Malware Scanner
To open a report that has already been generated for the project:
Double-click the report in the Reports tree item.
The report opens in the application associated with the report format.
If no reports have been generated for the project, double-click the Reports tree item to open the Generate
Report dialog box.
For more information on generating a report, see
Generating a report.
Run the malware scanner to identify malware on the device.
For more information, see
(page
).
81
82
Tree item
Project Analytics
Description
The Project Analytics tree item provides you with a comparative analysis overview. You can open an Activity
Analytics tab showing an overview of all device activity, as well as tabs that each focus on the phone, email, WhatsApp, Skype,
Gmail, and BlackBerry Messenger activities. For more
information, see
(page
).
4.1.1. Working in the project tree area
Open the tree items to drill down and locate specific information:
Click to expand or to collapse tree items.
Double-click a tree item to open detailed information in the data display area.
Click at the top of the project tree to expand all the items in the tree.
Click at the top of the project tree to collapse all the items in the tree.
Chapter 4: Orientation to the workspace
4.2. Data display area
Double-click an item to display it in a tab. A new tab is opened for each item.
83
84
There are five tab types:
Welcome tab
Extraction Summary tab
Data tabs, with sub-tabs that present a particular view, depending on the data
Timeline tab
Image tab (Hex view)
The data display area also displays additional windows such as the Trace window, and Watch list results.
To close a tab:
Do one of the following:
Click on the tab header.
Click at the top right of the data display area.
To jump to a specific tab
At the top right of the data display area, click , and select the desired tab from the open tabs list.
Chapter 4: Orientation to the workspace
4.2.1. Welcome tab
85
The Welcome tab is automatically displayed in the data display area when the application is launched and displays a list of recently opened files.
Each file in the list is displayed as a framed information group that contains the following items:
Device picture - A thumbnail image of the device from the application resources, if available. When unavailable, a general placeholder image is used.
File name - The name of the opened file, without the file extension.
86
File path - The file system path to the file location.
Device model - The identified device manufacturer and model, or BINARY if the opened file was a binary extraction.
Case name - If the report was given a case name, the name is shown. The name can be defined in the project settings.
Date and time - The date and time stamp in which the file was last opened.
Browse link - A direct link to the file in the system.
Remove recent item - Click to remove the item from the Welcome tab.
You can do the following:
Click on a framed item to open the files for decoding.
Click Browse to go directly to the file associated with it in the file system.
Close the Welcome tab. To reopen it, go to View > Show Welcome.
Chapter 4: Orientation to the workspace
4.2.2. Extraction summary tab
87
The Extraction Summary tab is displayed automatically whenever you open a new extraction for analysis.
To reopen the tab if closed, double-click the Extraction Summary tree item.
The Extraction summary tab can display the following information:
Extraction Info - Information related to the device extraction. Such as:
Extraction start date/time
Extraction end date/time
When the extraction started and ended.
Unit Identifier
The serial number of the device that performed the extraction (e.g.,
UFED Touch), or a unique ID if the extraction was performed by a PC application (e.g., UFED 4PC).
Unit Version
UFED software version (e.g., 4.1.0.220)
Selected Manufacturer
Manufacturer of the device (e.g., Apple)
Selected Device Name
Device name (e.g., iPhone 4)
Connection Type
Cable used for the extraction (e.g., Cable No. 100)
Extraction Type
Extraction ID
Type of extraction performed (e.g., File system)
Unique ID for each extraction type
88
Image Hash Information - Verification of the logged hash values of the parsed images. See
(page
).
Device Info - A summary of the specific device info pulled from the extraction file. See the
Info
item in
(page
).
Device
Device Content - Analyzed content, divided into the following categories:
Phone Data - The types of analyzed device data found in the extraction, such as call log, contacts, SMS messages, and so on. For the complete list of phone data types, see the
Analyzed Data
item in
(page
).
Data Files - The types of standard data files found in the extraction, such as images,
videos, audio, and text files. See
(page
).
To display the relevant information in a new tab in the data display area:
Click any of the tree items.
Chapter 4: Orientation to the workspace
4.2.3. Data tabs
Data tabs show files of a specific type (such as call log, contacts, SMS messages, and so on).
Each type of data file has several data display modes:
Application files
Image files
Video files
Hex View and File Info
Hex View, Image View and File Info
Hex View, File Info and Video View
Audio files
Text files
Document files
Databases
Hex View and File Info
Text View, Hex View and File Info
Hex View and File Info
Database View, Hex View, and File Info
Configurations Hex View and File Info
Data tabs display the data in a variety of sub-tabs, depending on the data type:
89
90
Table view - A list of all the files of a specific type (images, videos, audio, text, and so on) that were found during the data analysis process.
Folder view - View the folder structure of the data files paths in the reconstructed file system (for data files only).
Hex view - View the Hex data of a binary item
Image view - View the image. See
(page
).
Thumbnail view - View images by thumbnail (for images only).
File Info - View information about the file.
Database view - View the contents of database files.
4.2.3.1. Working in data tabs
Selecting items
Select items in the data display area to include them in any report you generate. By default, all items are selected.
To select multiple items, hold the SHIFT or CTRL keys (consecutive and nonconsecutive selection).
When an item is selected, press the space bar to select or clear the check box, which indicates if the item should be included or excluded from the report.
Chapter 4: Orientation to the workspace 91
To select all items at once, check the box in the column header (table view and time line) or check the Select all check box (thumbnail view).
Sorting columns
Sort each column alphabetically or by time.
Click the column header to toggle the order.
Re-ordering the columns
For your convenience, you can change the order of the columns. Your preference is retained for the duration of the session.
Drag the desired column to the desired location.
Hide or show columns
Right-click the column header and select the column name in the list.
Viewing more information
For data tabs containing textual information, by default the right pane is open, displaying the selected item's information.
To close or open the right pane, click .
92
Exporting data
1) To export the data in a particular tab, click the desired output in the toolbar: Excel , HTML ,
PDF , XML , KML (location data only), or EML (email data only).
The Export Dialog Window appears.
2) Do one of the following:
Enter the path where you want to save the report
Click and browse to and select the desired location.
3) Select the Include translations check box to include translated data.
4) Click OK.
The report is generated, and a message appears asking if you would like to open it in third party software.
Chapter 4: Orientation to the workspace
5) Click Yes or No.
The file is opened in the default third party software.
NOTE: When exporting to EML, a file is created for each email.
4.2.3.2. Text view
For text-based data files, view the data as text.
93
94
4.2.3.3. Table view for data files
For data files, the table shows the following information:
#
Indicates whether to include (checked) or exclude (unchecked) the item in the report generated.
Row number.
Indicates if the item is bookmarked.
Image
Name
Path
Size
Indicates whether the data file was deleted , or has an unknown status ( ).
A thumbnail of the image or an icon of the file type. (Image data files only).
The file name.
The root path of the data file.
The size of file.
Chapter 4: Orientation to the workspace
Metadata Additional metadata of the data file.
Created
Modified
Accessed
Bookmark Note
The creation time stamp of the data file.
The modification time stamp of the data file.
The last access time stamp of the data file.
Details of the bookmark.
95
In addition, indicators are displayed to show attachments, indicate video calls, and to show even direction.
Double-click on an item record (table row) to open a Hex Viewer tab showing the Hex data of the selected file.
96
4.2.3.4. Table view for analyzed data
For analyzed data, table view tabs display a list of all the events of a specific type (Call Log, Contacts,
SMS messages, and so on) that were found during the data analysis process.
Chapter 4: Orientation to the workspace
4.2.3.5. Folder view
Folder view shows how the items were organized in the device.
Select the folder checkbox to select all the items in that folder (including sub-folders). Selected items are included in generated reports. When you select an item, it is selected in all tabs in the data display area.
Click to open the folder in a new tab in the data display area.
97
98
The following folder information is displayed:
The folder name in the extracted file system.
The number of selected items in that folder (red in brackets).
The total number of items in that folder (in black).
4.2.3.6. Database view
To open database view, open a .db file in the File Systems tree item.
Chapter 4: Orientation to the workspace
Database view displays the contents of database files that were found in the extraction.
Database view consists of the following sections:
1) List of the database tables.
A number in parenthesis next to each table name designates the number of records in the database table.
Select a table in the left column to display its records in the right column.
2) Records display areas containing a list of data records in the selected database table.
3) Search field to filter the displayed records.
Click to export the selected database records to a CSV file.
99
100
4.2.3.7. Hex view
A Hex view tab appears for each binary item you open from the project tree. When opening, for example, an Image memory disk, a Hex view tab opens alone. When opening a binary item, for example, an image file, the Hex view tab may be accompanied by other tabs.
The Hex view tab contains the following sections:
Chapter 4: Orientation to the workspace
Hex tabs
101
a) Address column - The number of information column in Hex or Decimal value, displaying the start address of each row in the Hex and ASCII representation data sections b) Hex data view column - The Hex data of the selected item c) ASCII representation view column - The ASCII representation of the Hex data
An information frame automatically appears when you position the mouse over the information displayed in the Hex view. The information frame displays links (pointers) to analyzed data items, such as files and folders in the project tree, and search results associated with the pointed data.
Hex view toolbar
102
Save
Copy Selection
Find
Click to save the entire memory extraction to a local folder.
Copy the currently selected content of the Hex View tab to the clipboard.
Displays the Find dialog to search for all occurrences of specified information in the displayed Hex display pane.
Find Next
Displays the Find dialog box with the search parameters used in the latest search.
Add Bookmark Bookmark the currently selected content of the Hex display pane.
Go To
Redirect the offset to specific address in the content of the Hex display pane.
Enable Info
Frame
Toggles on/off the display of floating information frame at the cursor location.
Show Address Toggles on/off the left address column display.
Show ASCII view Toggles on/off the right ASCII representation column display
Chapter 4: Orientation to the workspace
Analysis information tabs
103
Located under the Hex view tab are Analysis Information tabs that display the following types of information related directly to the displayed Hex data:
Values - A wide array of value interpretations, such as 8, 16, 32, and 64 bit, various string encoding, date & time formats, and more, calculated on the fly for the currently selected data in the Hex view.
See
(page
).
Bookmarks - A list of bookmarks added in the displayed Hex data. See
(page
).
Highlights - A list of content segments markups highlighted in the displayed Hex data. The
number of highlight results is shown in brackets next to the tab name. See
(page
).
Search - Displays results of a search in the displayed Hex data. A new search results tab opens for each search query performed. The number of results for each search is shown in brackets next to the tab name.
You can rearrange the display of the Analysis Information tabs to suit your preference:
Double click the header strip of the section to display the entire section as a floating panel. Double click the floating panel header strip to dock it back to the default location (at the bottom of the
Hex View tab).
104
Double click the name label of any tab to display it as a floating panel. Double click the floating panel header strip to dock it back to the original location.
Drag the name label or floating panel over any of the docking labels that appear to dock it at that location in the Hex View tab.
4.2.3.7.1. Working in the Values tab
Decode the raw data to a variety of encoding types in real time, and expand them in the Values list.
1) To access the Values tab, click the Values tab at the bottom of a Hex view tab.
Chapter 4: Orientation to the workspace
2) Select a data segment in the Hex.
3) To display the decoded data, scroll to the desired encoding, and click to expand the display.
Some encoding options, such as 16 Bit, have sub-encoding types.
4) Fully expand or collapse all encoding types by clicking or .
105
106
4.2.3.7.2. Working in the Highlights tab
The Highlights tab contains a list of content segments that are highlighted in the displayed Hex data.
Each segment represents locations of analyzed data within the Hex. The Highlights tab enables you to locate particular types of analyzed data in the Hex. The number of highlight results is shown in brackets next to the tab name.
1) To access the Highlights tab, click the Highlights tab at the bottom of a Hex view tab.
2) In the project tree, click an Analyzed Data folder (for example, Contacts).
Chapter 4: Orientation to the workspace 107
The location of the selected folder is highlighted in the Hex view tab, and the list of chunks that the folder is comprised of is listed in the Highlights tab.
4.2.3.8. File Info tab
108
The File Info tab displays the following information about the data file:
FAT The File Allocation Table of the extended attributes.
Date & Time - Created, Modified, and Last Access time stamps of the data file.
General - The file size in bytes and the number of file system chunks of which the data file is comprised.
Offsets - The offset addresses of the data file in the Hex data.
EXIF - The embedded EXIF information logged by the camera (if it exists).
File Metadata - The general information of the image (capture time, resolution, size and color depth).
4.2.3.9. Viewing image files
1) Double-click an image in a data display tab.
Chapter 4: Orientation to the workspace 109
A new tab opens containing the image. The tab is divided into two sub-tabs; Image view and File
Info.
2) In the Image view tab, use the image controls:
When the image is enlarged, navigate the image.
Rotate image clockwise and anti-clockwise.
Zoom in and out. You can also adjust the zoom using the slider.
Zoom to fit the tab.
110
Reset the zoom to 100%.
Hide image controls.
3) Click the File Info tab to view the file information. For example, the File metadata section includes information such as the Capture Time, which is the date and time a photo was taken.
4.2.3.10. Playing video files
To play the video within UFED Physical Analyzer:
1) In the data table, double-click the media file that you want to play.
A new tab opens for the media file.
2) Click .
To play the video in the default program:
Right-click the media file and select Open with default program.
Chapter 5: Locating and analyzing information
Chapter 5: Locating and analyzing information
This section describes how to browse, search, filter, bookmark, and manage the information in your project.
111
5.1. Searching for information in a data tab
In Table View tabs, search for a particular item within the data table. The search is performed on all the data entries within the table.
In the Table Search box, enter any string.
The table updates to display only items containing the string you entered.
5.2. Using the quick filter
Use the quick filter tools to filter data in Table View tabs as follows:
112
Show all
Only selected
Only not selected
Deleted
Show all
Display images above 30KB
Display images above 100KB
Display images above 500KB
Filter images (by extension)
Show JPEG
Displays all items
Displays items that are selected
Displays items that are not selected
Displays deleted items
Show all images
Display only small images above 30KB.
Display only medium-sized images above
100KB.
Display only large images (500+KB)
Click to enable file type filtering:
Display JPG or JPEG files
Chapter 5: Locating and analyzing information
Show GIF
Show BMP
Show PNG
Metadata filter
113
Display GIF files
Display BMP files
Display PNG files
Filter image and video files by Metadata
(All, Without metadata or Has metadata) and Location (All, Has location or Without location).
Capture filter time Filter image and video files by capture time. The maximum range is displayed by default, and you can select a specific date and time range.
Translation filter Filter translated text to display all text, translated text or text that has not been translated.
NOTE: The toolbar items are context-sensitive, and only appear when relevant data is displayed.
114
5.3. Using the advanced filter
Use the advanced filter to filter the list based on a combination of several parameters.
1) In the filter toolbar, click Advanced.
2) Click Add field, and select a field from the drop-down list. The fields list comprises the columns in the current data tab.
3) In the box that appears for the selected field, enter any string or timestamp.
The tab displays only items that match the filter.
4) To add additional filters, repeat steps 2-3.
When you place additional filters in the Advanced search, the returned results match all specified criteria.
5) To clear the string you entered, click .
6) To clear all the entered strings, click Clear All.
Chapter 5: Locating and analyzing information
7) To remove the field filter, click .
8) To close the advanced filter, click Advanced.
115
5.4. Searching for information in all open projects
Use the All projects search box in the toolbar to search for information in all open projects.
1) Type any string in the All Projects box.
A list of matching results appear under the All Projects search field. The results are sorted by open project. Within each open project, the results are sorted by categories according to type (SMS, messages, contacts, files, and so on). The number of matching results found in each type category is also displayed.
2) Click to collapse or expand the projects.
116
3) Do one of the following:
Click next to the project name to view the results of the search in that extraction in a tab in the data display area.
Select Show All from the top of the quick results list to display a results tab in the data display area listing all the matching search results. The matching string in each item is colored in red.
As in the quick results list, the results tab lists the results by type.
5.5. Browsing the file system
UFED Physical Analyzer has the ability to reconstruct and display the device file system in a tree structure.
To browse the device file system:
1) In the File Systems tree item, click the or icons at every node to expand the tree item.
2) Continue drilling down in the file system to explore its content.
Files in the reconstructed file system display one of the following icons:
- Existing file found in the system
- Deleted file data found in the file system
3) When you reach a file that you want to open, double-click it to display its information in the data display area.
Chapter 5: Locating and analyzing information 117
The number information tabs displayed for the file changes according to the file type. For example, an unknown file may display only the Hex View and File info tabs, while a jpeg image may display additional Image view and Meta data tabs. The default view is Hex view.
For more information on working with Hex view, see
(page
) and
(page
)
4) While the Hex extraction of an image is displayed in the data display area, click a file under the File
Systems tree item to highlight the data portion of this file in the Hex data in the data display area.
5.6. Timeline view
Timeline view is a powerful tool that enables you to analyze data in chronological order, to identify the order of events and make connections between them.
Timeline view has two views; table and graphic.
118
In table view, the events are displayed in a table, organized by date and time.
Chapter 5: Locating and analyzing information 119
Click to group or ungroup the events by date.
In graphic view, the events are displayed in a graph, enabling you to quickly identify activity spikes that may be of interest.
To scroll forwards and backwards in the timeline, use the , , and buttons.
120
You can increase or decrease the level of detail in the Timeline Graph View:
To increase the time resolution, click .
To decrease the time resolution, click .
Events that occur within close proximity are flagged in groups.
Click to open another timeline view tab for the group of events.
5.7. Accessing conversation view
Communication-based data, such as call logs, email, SMS and MMS messages, and so on, can be displayed in a conversation view layout for easier and better tracking over the communication between two or more parties. You can search for messages within a chat, select the messages to include within a report (by default all chat messages are included), print, or export the conversation.
To access and use conversation view:
1) In a communication-based data table, select one of the records.
2) Click .
A conversation tab opens, displaying related items as a conversation between the sending and receiving parties of the selected item.
Chapter 5: Locating and analyzing information 121
122
3) To translate or delete translated text, click and then select Translate all or Delete all translations.
4) To print the conversation, click .
5) To view a print preview, click .
6) To export the conversation, click the desired output in the conversation tab toolbar:
Excel , HTML , PDF , XML , or Word .
7) To change the order of the conversation, click and then select Oldest message first, or
Newest message first.
8) To filter messages, enter text in the search box.
9) To add or edit bookmarks, click .
10) Select a check box to include specific messages in the report, (or select all messages or no messages).
Chapter 5: Locating and analyzing information
5.8. Working with watch lists
123
Run a watch list of keywords against your extracted data to identify and highlight important and relevant information.
The watch list search can either be activated automatically or run manually on selected decoded data.
5.8.1. Creating a watch list
1) Do one of the following:
In the toolbar, click .
In the Tools menu, select Watch List Editor.
124
The Watch List Editor appears.
2) Click , and select New.
Chapter 5: Locating and analyzing information 125
3) In the Watch list name box, enter a name for the watch list.
4) To set the watch list to find keywords only in data types in the project, click Find in, and select the desired data types.
126
When you run the watch list, only selected data types are checked for matches.
Chapter 5: Locating and analyzing information
5) In the Enter description box, enter a general description for the watch list (optional).
6) To set the watch list to run automatically when you open projects, click Auto-activate.
7) Click New to add a new keyword.
A new keyword row appears in the Keywords list.
8) For each keyword, set the following, as desired:
Entry Value: Enter the keyword.
Match case: Select to match the case of the keyword
Whole word: Select to match the whole keyword.
Color: Click and select the color you want matched keywords to be shown in.
9) Do one of the following:
Click Apply to save the watch list and keep the Watch List Editor open.
Click OK to save the watch list and close the Watch List Editor.
Click Cancel to close the Watch List Editor without saving your changes.
127
5.8.2. Editing a watch list
1) In the Watch List Editor, select the watch list that you want to edit.
2) Edit the watch list parameters and keywords that you want to change.
3) To filter the keyword list to locate a particular keyword, type the keyword in the Enter text to filter box.
4) To edit a keyword, click the relevant keyword in the list, and make the desired changes.
128
5) To delete a keyword, click .
6) When you have finished making changes, do one of the following:
Click Apply to save the watch list and keep the Watch List Editor open.
Click OK to save the watch list and close the Watch List Editor.
Click Cancel to close the Watch List Editor without saving your changes.
5.8.3. Importing a watch list
The export and import functions enable you to share watch lists and receive watch lists from your colleagues. Import existing watch lists (*.csv files) that were saved from or created by UFED Physical
Analyzer.
You can also import a CSV file that contains a list of keywords, which can then be used as watch list keywords. This option will import the keywords without any formatting and will look to find all data types by default.
1) In the main toolbar, click .
The Watch List Editor appears.
2) Click , and select Import.
3) Browse to the location where your watch list is saved, select the CSV file, and click Open.
The watch list appears in the Watch List Editor. An example is displayed next.
Chapter 5: Locating and analyzing information 129
130
5.8.4. Exporting a watch list
Export watch lists to save the watch list as a *.csv file for later use, or to share with others.
1) In the Watch List Editor, select the watch list that you want to export.
2) Click .
Chapter 5: Locating and analyzing information
3) Browse to the location where you want to save your watch list, and click Select Folder.
The watch list is exported. It will be saved by default as [name of watch list].csv.
5.8.5. Deleting a watch list
1) In the Watch List Editor, select the watch list that you want to delete.
2) Click .
131
3) Click Yes.
The watch list is deleted.
132
5.8.6. Running a watch list
You can run watch lists on open projects.
5.8.6.1. Running a watch list on particular projects
When you run a watch list from the Watch List Editor, you can select which watch lists to run, and on which projects you want to run them.
1) In the toolbar, click to open the Watch List Editor, and select the watch list you want to run.
2) Click .
A list of open projects appears.
3) Select the open project(s) that you want to run the search on.
NOTE: A tick mark shows that the selected watch list is currently active for the project.
4) Click Apply.
UFED Physical Analyzer searches for keywords in the selected project(s). When complete, the watch list results appear in the Watch Lists tree item.
If the watch list is assigned to only particular information types (see
(page
)), only matches to those types appear in the watch list results.
Chapter 5: Locating and analyzing information
5.8.6.2. Running a watch list on your current project
133
When you run a watch list from the project tree, you can select which watch lists to run on the project that you are currently working in. If you have more than one project open, the selected watch lists run on the project that you last clicked in in the project tree.
1) In the toolbar, click .
A list of watch lists appears.
2) Select the watch list(s) that you want to run on the project you are currently working in.
NOTE: A tick mark shows that the watch list is currently active for the project.
3) Click Apply on the project that is in focus in the project tree.
NOTE: When you click from the toolbar, you can only run the watch list(s) on the project that you last clicked in in the project tree.
UFED Physical Analyzer searches for keywords in the selected project(s). When complete, the watch list results appear in the Watch Lists tree item.
If the watch list is assigned to only particular information types (see
(page
)), only matches to those types appear in the watch list results.
134
5.8.7. Locating a watch list
1) Do one of the following:
In the toolbar, click .
In the Tools menu, select Watch List Editor.
The Watch List Editor appears.
2) In the Enter text to filter box, enter the watch list name in whole or in part and click .
3) The list of watch lists is filtered accordingly.
5.9. Bookmarking information (entity bookmarks)
An entity bookmark is a quick reference pointer you can create on individual items:
An Analyzed Data item such as a call from the call log, a contact record, an email message, etc.
See the
Analyzed Data
item in
(page
).
A Data Files item such as an image file, a video file, a text file, and so on. See the
Data files
item in
(page
).
The entity bookmarks you create are managed in the Entity Bookmarks tree item. The number of entity bookmarks in the project is shown in brackets next to the section name.
Double-click Entity Bookmarks to list the entity bookmarks in a tab in the data display area.
Selected entity bookmarks are included in reports that you generate.
Chapter 5: Locating and analyzing information 135
Double-click any entity bookmark to go to the bookmarked item in the appropriate display tab.
For example, double-click an entity bookmark to an SMS message to open the list of SMS messages in an Analyzed Data display tab, with the bookmarked item highlighted.
Hover over a to display the bookmark name and description.
To print or export just the entity bookmarks list, click the desired output in the Entity Bookmarks tab toolbar: Excel , HTML , PDF , or XML .
5.9.1. Creating a new entity bookmark
Entity bookmarks can be added to items in Table view.
1) Select the item you want to bookmark.
2) Click .
136
The Add/Edit Bookmark dialog box appears.
3) Enter a name and a description to the new entity bookmark, then click OK.
A new entity bookmark pointing to the selected item is added to the entity bookmarks list of the project. The bookmarked item record is marked with a .
5.9.2. Editing an entity bookmark
1) Select one of the following:
An entity bookmark record from the list of Entity Bookmarks in the project tree.
A bookmarked item (marked with ).
Chapter 5: Locating and analyzing information
2) Click in the Table view toolbar.
The Add/Edit Bookmark dialog box appears.
3) Edit the name or description, then click OK.
5.9.3. Deleting an entity bookmark
1) Select one of the following:
An entity bookmark record from the list of Entity Bookmarks in the project tree.
A bookmarked item (marked with ).
2) Click in the Table view toolbar.
The bookmark is deleted.
137
5.10. Device Locations
5.10.1. About location data
In UFED Physical Analyzer, location data is drawn from different locations within the device. The following location data is analyzed:
138
Analyzed data > Locations
Location data in the Locations item is divided into the following categories:
Cell towers
WiFi networks
Harvested Cell towers
Harvested WiFi networks
Media locations
Harvested and non-harvested location information
Harvested and non-harvested location information is taken from the device database.
The device location is identified by the dev
1) Collection - As the device changes locations when traveling with its owner, it collects the location information of each cell tower and Wi-Fi Network Receptor as it enters their vicinity. These locations are called "harvested" information. The location calculated in this way is considered accurate.
When the device Wi-Fi is turned on, the device periodically sends the harvested locations to Apple
(iPhone devices) or Google (Android devices). The harvested information is then deleted from the device.
Chapter 5: Locating and analyzing information 139
When the device Wi-Fi is turned off, or there is no Wi-Fi connection available, the device harvests and stores the locations of the cell towers and Wi-Fi networks, and then sends the information when the Wi-Fi is turned on, or connection is available.
2) Download - The device connects to the location services provider (Apple (iPhone devices) or
Google (Android devices), requesting location services. Apple or Google send information about cell tower and Wi-Fi networks in a ~2km radius. This information is saved on the device and is called "non-harvested" information.
Location data in the Cell towers, WiFi networks, Harvested Cell towers, and Harvested WiFi networks categories includes:
GPS information - longitude and latitude
Accuracy - radius in meters within which the device is located.
Confidence - in %. How confident the service provider is that the phone indeed lies in the calculated location.
Timestamp
Media locations
Location data in Media locations is taken from the location stamp associated with each media file.
140
Analyzed data > Journeys
Location data in the Journeys item is taken from the GPS applications on the device. The categories displayed in this item are divided by application.
Analyzed data > GPS fixes
Location data in the GPS fixes item is taken from GPS devices and GPS applications on the device. The categories displayed in this item are divided by application and source.
5.10.2. Viewing location data on BING
The maps function is free of charge but requires internet access. It is only available to UFED Physical
Analyzer users with a valid license.
Chapter 5: Locating and analyzing information
To activate Bing maps:
The first time UFED Physical Analyzer is started you will be asked to activate your Bing maps. The following screen is presented:
141
Click Activate to activate your Bing maps. After activation the following screen is presented:
142
If activation is not performed at startup, Bing maps can be activated later via the Help menu.
Users can browse and search topographically-shaded street maps for many cities worldwide. Two primary types of street map views are available to users: Road View, Aerial View
Road View
Road view is the default map view and displays vector imagery of roads, buildings, and geography.
Aerial View
Aerial view overlays satellite imagery onto the map and highlights roads and major landmarks for easy identification amongst the satellite images.
Chapter 5: Locating and analyzing information
5.10.3. Markers and information windows
143
Markers signify the location where a person's device registered.
The color of the marker signifies which person was registered at a particular location. At a low zoom level, markers show the approximate location, and may include the data of more than one person.
The following markers are examples of the types of markers that are displayed in the map:
At low zoom level, this marker displays a number of recorded locations in a particular area.
Indicates the location of the cell tower that registered the person's device.
Indicates the location of the WiFi network receptor that registered the person's device.
Indicates the recorded location or a media object.
Indicates the location of an unidentified entity that registered the person's device.
144
5.10.4. Retrieving addresses
You can view street addresses for longitude and latitude positions extracted from a device. This can then be used to filter the locations. You can select single or multiple locations up to a maximum of
200. You can retrieve street addresses in the following views: Project search, Timeline views and Watch
List results.
NOTE: To use this feature, you must activate the Bing map service and be connected to the Internet.
To retrieve an address:
1) In one of the Device locations table views, select a row, right-click and select Retrieve address, or click .
NOTE: To retrieve multiple addresses, you can use Ctrl button to select the locations.
The retrieved addresses are displayed in red in the column called Map Address.
Chapter 5: Locating and analyzing information
To filter locations:
Click and then select one of the following options:
Show All to display all locations.
With map address to display locations that have a map address.
Without map address to display locations that do not have a map address.
145
146
Chapter 6: Translating decoded data
Chapter 6: Translating decoded data
147
Translate the content in your extractions that are in foreign languages without having to wait for a translator to become available, or to use Internet-based tools.
The Translation feature enables you to translate decoded data on demand, so that an investigator can understand the information available in an extraction. The Translation feature is an offline translation solution, where you do not need to be connected to the Internet. You can select single, multiple or all table entries for translation. Both the original and the translated text can be included in the report.
The lists of supported languages are as follows:
Chinese (Simplified)
Chinese (Traditional)
Dutch
German
Hebrew
Italian
French
Japanese (requires additional payment)
Korean
Polish
Portuguese
Russian
Spanish
Ukrainian
148
6.1. Using the feature
To use this feature, you need do the following:
Update your license with the selected languages
Download the translation pack
Translate the decoded data
6.2. Updating your license with the selected languages
You can select up to five languages for free from the My Products page in MyCellebrite . If additional languages are required, you can purchase the Basic Language Package. You cannot change a language after saving, but you can request additional languages .
NOTE: If you want to translate to a language other than English, you should select it as well.
6.2.1. Selecting languages in MyCellebrite
To select languages:
1) Log in to MyCellebrite and select the My Products tab. The following window appears.
Chapter 6: Translating decoded data
2) Select and click Select Languages. The following window appears.
149
150
3) Select up to five translation languages and click Next. The following window appears. For additional languages, click Need more languages and complete the form.
Chapter 6: Translating decoded data
4) Click Save. The following window appears.
151
152
5) Update the license for the product and download the language package.
Chapter 6: Translating decoded data
After updating your product license with the selected languages, you can use the following procedure to view the languages included in the translation license.
To view the translation license languages:
Select Tools > Translation > Show supported languages.
The following screen appears.
153
154
6.2.2. Downloading the translation pack
You can download the Translation pack from the application or from your my.cellebrite.com
account.
The Translation pack includes a version number, which enables you to track the version installed on the computer.
To download the translation pack:
1) Select Tools > Translation.
2) Select one of the following options:
Download translation pack: Downloads the translation pack (this option is not available if there is no Internet connection).
Install translation pack from file: Installs the translation pack from a file. Select this option if there is no Internet connection.
3) Follow the on-screen instructions to install the Translation pack.
NOTE: To uninstall the Translation pack, go to the Windows Uninstall page, and select the
Language Translation Package, (Publisher: Cellebrite Mobile Synchronization) from the list.
Chapter 6: Translating decoded data
To view the translation pack version number:
Click Help > About.
The following screen appears.
155
156
6.2.3. Translating the decoded data
By default, the target language is set to the same language as the interface language. If required, you change the target language to a different language.
To change the translation language:
1) Select Tools > Settings.
The following screen appears.
2) Select the Translation Language. That is the language to which you want to translate the text. You can only select one Translation Language. To request additional translation languages, select Get more languages.
3) Select the Show translation language by default check box to display translations by default.
Clear this check box so that the translation will not appear when you translate text. To see the translation select View translated.
Chapter 6: Translating decoded data
To translate decoded data:
1) Click to select the data that you want to translate.
2) Click the button, or right-click and select Translate selected or click then select one of the following options:
Translate all: Translate all entries in the specified view.
Translate selected: Translate the select text only.
NOTE: If required, use the Delete translation option to delete the translated text.
The translated text is indicated by a yellow bar.
To view the original text:
1) Right-click the text and select View source, or click the
The original text is indicated by with a gray bar.
button.
and
157
158
To filter text:
Click and then select one of the following options:
All to display all text.
Translated to display text that has been translated.
Not translated to display text that has not been translated.
6.2.4. Reporting
When creating reports or exporting data, you can specify whether to include the translated text or not. If you choose to display the translated text within the report, the summary table will include an additional entry called: Translated languages, with a list of the languages. The translated content appears below the original text under the heading: Translation. For more information on reports, see
Generating a report on page
.
To include the translated text in reports:
1) Go to Tools > Settings > General Settings > Report Defaults.
2) Select the Include translation check box.
Chapter 6: Translating decoded data
To include translated text in exports:
1) Click an Export option (
2) Select the Include translation check box.
).
159
160
Chapter 7: Working with project analytics
Chapter 7: Working with project analytics
161
Project Analytics enables you to view the extraction data in terms of the number of communication events between the device and other parties, identified by phone number, or other user identity (such as email address, Skype handle, and so on). The analysis enables you to easily and efficiently identify communication patterns between the device and other parties. For example:
Parties most communicated with via all types of communication methods
Parties most communicated with via phone calls, SMS, and MMS
If the device user exchanged a large number of phone calls, SMS, and emails with a certain contact, it is easy to see the volume of this communication.
Communication events are listed by volume per type. The following communication events are supported:
Phones - Lists outgoing, incoming, and missed calls, and sent, received, and draft SMS and MMS.
Emails - Lists emails sent, received, drafts, and emails of unknown status.
WhatsApp - Lists messages sent, received, and drafts.
Skype - Lists calls, SMS, and chat messages.
BlackBerry Messenger - Lists chat messages.
162
Project analytics runs automatically when you open an extraction file.
To view project analytics:
1) Click next to the Project Analytics tree item to view the analytics results displayed in the
Project Analytics tree item.
2) Double-click the Project Analytics tree item to open a tab that displays the top five activities per contact.
3) To view a comparative overview of all communication events, double-click the Activity Analytics tree item. The view is sorted in descending order, based on the total number of events.
4) To view the events by communication identifier, double-click the desired identifier tree item.
5) Click the column header to sort the information in the column.
NOTE: Project analysis information can be included in a report. For more information, see
Generating a report.
Chapter 8: Scanning for malware
Chapter 8: Scanning for malware
163
Run malware detection on your extraction to search for malware.
When you scan for malware, UFED Physical Analyzer uses the last-used signature database. If this is the first time you are using the malware scanner, or if you want to update the database before you scan,
follow the steps in
(page
). If you are working on a
computer without an internet connection, follow the steps in
(page
).
1) Select Tools > Malware Scanner > Scan Malware or click .
2) Select the file system(s) that you want to scan, and click Scan.
164
UFED Physical Analyzer scans the project for malware. The results are displayed under the Malware
Scanner tree item.
3) Double-click the Malware Scanner tree item to open a data display tab.
The data shown includes the malware type and malware information, such as the name.
To include the results in a report, select Infected Files in the Report Dataset area. For more
information, see
.
8.1. Updating the signature database (online)
Update the signature database before the first time you use the malware scanner in order to populate the database, and thereafter in order to keep the signature database up to date.
NOTE: Once the signature database is populated, you can run the malware scanner using the existing database. It is strongly recommended that you update the signature database on a regular basis in order to keep it current.
1) In the Tools menu, select Malware Scanner > Update signature database.
Chapter 8: Scanning for malware
2) Click Update from server.
The database is populated.
3) Click Close.
You can now scan the project for malware.
165
166
8.2. Updating the signature database from file (offline)
Update the signature database from file when you are working on a computer that does not have an internet connection.
NOTE: Once the signature database is populated, you can run the malware scanner using the existing database. It is strongly recommended that you update the signature database on a regular basis in order to keep it current.
1) In Windows Explorer, in the main UFED Physical Analyzer directory, copy the BitDefenderUpdater directory to an external storage device.
2) Transfer the BitDefenderUpdater directory to a computer that has internet connection without proxy settings.
3) In the BitDefenderUpdater directory, double-click Malware Definitions Downloader.exe.
Chapter 8: Scanning for malware
4) Select the computer operating system of the computer on which UFED Physical Analyzer is installed.
5) Click Download.
167
168
6) Click Open containing folder.
7) Copy the definitions.msd file to an external storage device, and transfer it to the computer on which UFED Physical Analyzer is installed.
8) Click Close to close the Malware Definitions Downloader.
NOTE: To streamline your workflow and save time, it is recommended that you always use the same computer to download the definitions.msd file. When you download the definitions.msd file to this computer in the future, the Malware Definitions Downloader updates the file instead of downloading the entire file. Make sure that you do not delete the definitions.msd file from this computer.
9) In UFED Physical Analyzer, select Tools > Malware Scanner > Update signature database.
Chapter 8: Scanning for malware
10) Click Update from file.
169
170
11) Browse to the malware definitions database file (*.msd), and click Open.
12) Click Start.
Chapter 8: Scanning for malware
The database is populated.
13) Click Close.
You can now scan the project for malware.
171
172
Chapter 9: Generating a report
Chapter 9: Generating a report
1) You can generate a report of the information in the project. UFED Physical Analyzer provides a report wizard to help you through the steps of creating a report. Do one of the following:
Select Report > Generate Report from the application menu.
Click Generate Report in the Extraction Summary tab.
Double-click Reports in the project tree.
The Generate Report window appears.
173
174
2) In the File Name, select the name for the new report you want to create.
3) In the Save to, select the folder in which you want to all reports to be created. This folder can be used for all reporting as each report will occupy a separate sub-folder.
4) In the Report sub-directory select a name for the folder where you want all selected reports to be created. The default is the current date and time.
5) In the Project select the project or projects you want to include in this report. Only projects that are already opened in UFED Physical Analyzer are available for reporting.
Chapter 9: Generating a report 175
6) In the format field choose which of the available formats you want for the report. More than one format can be chosen and a report for each format will be generated.
7) In the case information fields you can provide the following:
Case number
Case name
Evidence number
Examiner name
Department
Location
176
NOTE: Default settings for these fields. See
(page
). See
(page
) and
(page
) for other defaults. Additionally, the
last 10 values entered in these fields are also available in the drop down.
8) Your form should now look like this example:
9) From the following screen select the data to include in the report:
Chapter 9: Generating a report 177
a) Extraction - analyzed data and data files to be included in the report. b) Examiner - Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. This selection is for the whole report and applies to all projects within the report. TIP: To shorten the report generation process of large projects do not select these options.
Select Include translations to include translated text. The summary table will then include an additional entry Translated languages, and the translation of the content will appear below the original text with title Translation.
178
c) Analytics - this section appears when there is Analytics available in the project. Select the relevant Analytics item(s) to include them in the report.
10) The security screen appears. Password protection can be placed on PDF, Word and Excel reports:
Choose the format and provide a password.
11) Select Default sorting to sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear Default sorting to sort the items according to the selected sorting field and the sorting order (ascending or descending) that was set by the user in each of the data display tables.
Chapter 9: Generating a report 179
12) For each format chosen for this report you can specify report parameters as follows: a) Word, HTML and PDF Reports:
Disable models categorization - Select to disable the separation and generate a report in which every data item is generated as a single section without subcategories separation. By default, a categorized report in which each category in the data items group is generated as a separate section in the report is generated. For example, when generating a report with SMS, select the check box to generate the SMS messages as a single list, or clear the check box to break it to a separate list for each category of SMS messages (Inbox, Outbox, Drafts, etc.).
180
Logo Header - Text area where you can enter and format custom text to appear in the report header before the logo image.
Logo - Click Select Image File to add the logo image to appear in the report header.
Supported file formats are: BMP, JPG, GIF, and PNG.
Logo Footer - Enter and format custom text to appear in the report footer after the logo image.
Show totals for items not in the report - Add a Total column to the report that displays the total number of items that were excluded from the report.
Show extended deleted state - Include the state (Intact, Deleted, or Unknown) of deleted items in the generated report. When not selected, logs only the state of deleted items as Yes, and is left empty for other states.
Number of lines for email preview - Set the maximum number of lines from each email message to appear in the report.
Display full email body - Display the entire message body.
Number of messages per chat - Set the maximum number of messages per chat message to appear in the report.
Display all chat messages - Display all chat messages in the report.
Font Family - for PDF reports only.
Split HTML report - for HTML reports only. Ensure that each section of the report starts on a new page.
Chapter 9: Generating a report
b) Excel (all formats) and ODS report:
181
The excel report is compatible with OpenOffice - Select to ensure the Excel report can be opened in OpenOffice.
Generate Contact Identification Data - Select to add a sheet to the Excel report that provides a list of unique contacts based on type. c) XML and UFED Report package:
There are NO additional settings required for either of these reports. If the report formats requested only include XML and/or UFED report then no further input is required.
13) Click Finish.
NOTE: Finish is unavailable until all the required fields are filled. A yellow warning icon is displayed next to all required fields that are not yet complete.
When the report is successfully generated, you are prompted to open the generated report file.
The file opens using the associated application to the file format installed in the workstation.
Once a report has been generated for the project, it can be accessed from the Reports section in the project tree. Double click on any of the generated reports to open it in the associated application installed in the workstation. Right click any of the generated reports to open the report file, or select
Open containing folder to browse the files and folders of the report.
182
Chapter 10: Performing extractions
Chapter 10: Performing extractions
183
In UFED Physical Analyzer, perform device extractions in the following ways:
1) For iOS devices, perform advanced logical extraction, physical extraction, file system extraction or
Passcode recovery from the device using the iOS Device Extraction application
2) For GPS or mass storage, perform an extraction via UFED Physical Analyzer
10.1. Extraction from iOS devices
Perform a physical or advanced logical extraction from an iPhone, iPod, or iPad device, using iOS
Device Extraction.
10.1.1. Prerequisites
To perform an extraction from an iOS device, you will need:
UFED Physical Analyzer installed on a PC
UFED Cable Number 110 or UFED Cable A with Tip T-110 or Apple 30 pin USB cable supplied with the device
184
UFED Cable Number 210 for iOS Logical Extractions from iPhone 5, iPad Mini and iPad4
NOTE: Extraction from iOS devices is not supported in Virtual Machine environments.
In addition, an internet connection is required the first time you run iOS Device Extraction in order to download the necessary support package. Alternatively, the support package can be downloaded using a different computer and copied manually to the computer running iOS Device Extraction. iOS
Device Extraction automatically notifies you when a software update is available.
10.1.2. Performing physical extraction
Perform physical and file system extractions from the following devices running iOS version 3.0 or higher:
iPhone 2G
iPhone 3G
iPhone 3GS
iPhone 4
iPad 1
iPod Touch 1G
iPod Touch 2G
Chapter 10: Performing extractions
iPod Touch 3G
iPod Touch 4G
iPod Nano 5G
10.1.2.1. Performing physical extraction from non-encrypted iOS devices
1) Select Extract > iOS Device Extraction or click to launch iOS Device Extraction.
185
186
2) Click Physical mode.
The first time that you run iOS Device Extraction, or when a new support package is available, you are prompted to download the iOS Device Support Package. The support package contains the latest utilities that enable iOS Device Extraction to work with a variety of devices and iOS versions.
Depending on your internet connection, the download may take some time.
If your computer is unable to connect to the internet, use a computer with an internet connection to download the latest support package file as follows: a) Go to http://www.cellebrite.com/ios. b) Click Download, and save and copy the file to the computer running iOS Device Extraction. c) When prompted to install the support package, click Install from file, then navigate to the location of the support package file, and click OK.
3) Follow the displayed instructions to power off the iOS device and then click The device is off.
Chapter 10: Performing extractions
4) Follow the displayed instructions to activate the iOS device in Recovery Mode.
187
188
Chapter 10: Performing extractions
The process automatically continues to the next step.
189
After a device in Recovery Mode is detected, iOS Device Extraction displays some device information, such as serial number, hardware version, iOS version and more.
5) If you need this information, click Copy to copy the device information to the clipboard.
NOTE: When a range of versions are displayed, the version of the device may be any version within the displayed range. For example, if the version shows 4.0-4.0.2, the actual version can be
4.0, 4.0.1 or 4.0.2.
190
6) Click Next to continue.
7) Follow the displayed instructions to set the device to DFU (Device Firmware Upgrade) mode. iOS Device Extraction does not affect the device firmware or user data.
NOTE: This step requires precise timing. If the device accidentally turns on, disconnect it from the cable, turn it off, then go back to step 4.
Chapter 10: Performing extractions
When the device is in DFU mode, a forensics program required for the extraction automatically uploads to the device.
191
The device is now ready for extraction.
8) Choose the desired extraction type.
192
9) Choose the desired extraction method:
For Physical Extraction: User data partition, System partition, or both.
For File System Extraction: User data partition or both.
Choose the location to which to save the extracted data. You can save it locally on the computer or to any removable storage device.
Chapter 10: Performing extractions 193
10) Click Next to continue.
NOTE: If the device is locked with a passcode, see
(page
).
11) Wait for the extraction process to complete.
The duration varies depending on the extraction method, the device model, the amount of data on the device, the extracting computer, and other parameters.
194
The following options are available at the end of the extraction process:
Open in UFED Physical Analyzer Loads the extraction file in UFED Physical Analyzer.
Open file location Opens the folder that contains the extraction files.
Turn off the device and exit Turns off the device and sets it back to normal mode.
Back to extraction options Returns to the extraction methods screen (step 8).
12) Turn off the device and set it back to normal mode.
10.1.2.2. Performing physical extraction from encrypted devices
iOS Device Extraction can extract data from encrypted devices. The amount of data that can be extracted depends on the type of passcode the device is locked with.
There are two kinds of passcodes:
Simple passcode 4 digits from 0 to 9 (e.g. 1234, 8787, 2580, etc.)
Complex passcode Any combination of numbers, letters and symbols (e.g. 93qP@Mv, iLoVeYoU, etc.)
The decryption process happens in UFED Physical Analyzer and not during the iOS Device Extraction.
Most data, such as contacts, messages, photos, some emails, and more, can be decrypted without knowing the passcode. However, to decrypt some of the saved passwords and emails, you need to know the device passcode.
Chapter 10: Performing extractions
If the device is locked with a simple passcode, iOS Device Extraction automatically recovers the passcode for you. If the device is locked with a complex passcode, you can manually try as many passcodes as you like, or continue the extraction without being able to decrypt some of the saved passwords and emails.
195
If the device isn't locked with a passcode, all data is extractable even if the device is encrypted.
10.1.2.2.1. Extracting data from a device with a simple password
1) Perform steps 1-7 of
(page
).
When the device is ready for extraction (step 8), an additional Passcode Recovery option is added to the two extraction options (Physical Extraction and File System Extraction).
The Passcode recovery option provides the device passcode so you can unlock and use the device.
2) To extract and recover the passcode in a single process, choose Physical Extraction or File System
Extraction.
196
The following steps demonstrate a physical extraction process (starting at step 8 of Performing the
Data Extraction), but they are the same for a file system extraction.
3) Click Physical Extraction.
4) Choose the partition you wish to extract, and the location where you want to save the extraction, then click Next.
5) If you don't know the passcode, click Recover the passcode for me to recover the passcode prior to the extraction.
Chapter 10: Performing extractions 197
6) If you know the passcode, enter it in the text box field below. A check mark verifies if the correct passcode was entered.
7) Click Continue.
The extraction process starts.
10.1.2.2.2. Extracting data from a device with a complex password
1) Perform steps 1-7 of
(page
).
When the device is ready for extraction (step 8), an additional Passcode Recovery option is added to the two extraction options (Physical Extraction and File System Extraction).
Use the Test Passcodes option to test and verify as many passcodes as you like in real time. iOS
Device Extraction cannot recover a complex passcode.
Most data is decrypted in UFED Physical Analyzer, but some of the saved passwords and email files are not decrypted unless the complex passcode is known.
The following steps demonstrate a physical extraction (starting at step 8 of Performing the Data
Extraction), but they are the same for a file system extraction.
2) Click Physical Extraction.
3) Choose the partition you wish to extract and the location to which you want to save the extraction, then click Next.
198
4) Do one of the following:
If you know the complex passcode, enter it manually. If you do not know the complex passcode, be aware that some data cannot be decrypted by UFED Physical Analyzer.
Use the text field to test as many passcodes as you like without locking the device. A check mark appears when you enter the correct passcode.
5) Do one of the following:
To start the extraction with the complex passcode, click Continue >.
To start the extraction without the complex password, click Continue without passcode.
Chapter 10: Performing extractions
The extraction process begins.
199
10.1.3. Performing advanced logical extraction
Perform an advanced logical extraction from UFED Physical Analyzer to extract more information than from logical extraction using the UFED unit.
Perform an advanced logical extraction from the following devices:
iPhone 2G/3G/3GS/4/4s/5/5s/5c
iPad 1/2/3/4/mini
iPod Touch 1G/2G/3G/4G
iPod Nano 5G
10.1.3.1. Performing advanced logical extraction
1) Select Extract > iOS Device Extraction or click to launch iOS Device Extraction
2) Click Advanced Logical extraction.
200
3) Follow the displayed instructions to power on the iOS device and connect the device to your computer, then click Next.
Chapter 10: Performing extractions 201
NOTE: If the connected device is not recognized, disconnect the device and reconnect it to a USB port at the rear of the PC.
If the iOS device is locked the Locked Device screen is displayed. If the .plist file for the locked device is available from the device owner's PC then this .plist file can be loaded in the Locked Device screen and then click Retry. If the device is locked and no .plist file is available then click Close.
NOTE: To use the .plist file, you need to run the UFED application as an administrator.
202
Chapter 10: Performing extractions 203
4) Choose a Method of Advanced Logical extraction. Depending on whether the device is jailbroken and/or encrypted, different methods of extraction are made available: a) Method 1 - Extraction of a rich set of data including SMSs, MMSs, application data and locations. Call logs, email body and attachments are not extracted. Extended extraction time. b) Method 2 - Extraction of a set of data including call logs, SMSs, MMSs, application data and locations. This decoding process may require entering the iTunes backup password. c) Method 3 - Extraction of the richest set of data including call logs, SMSs, MMSs, emails, application data, and locations.
In addition the application indicates a specific recommended method per iTunes backup configuration and jailbroken status.
204
For a jailbroken iOS device this screen is displayed -
Chapter 10: Performing extractions
For a jailbroken encrypted iOS device this screen is displayed -
205
206
For a non-jailbroken encrypted iOS device this screen is displayed -
Chapter 10: Performing extractions
For a non-jailbroken non encrypted iOS this screen is displayed
207
NOTE: The extraction time will depend on the amount of data on the iOS device and on the method chosen. A Method 2 extraction from a heavily used device could take several HOURS to complete.
5) Choose the location to save the extracted data. Ensure that there is enough disk space on your chosen location. You can save it locally on the computer or to any removable storage device or to a network location.
208
6) Click Next to continue.
7) A progress bar will be shown. Wait for the extraction process to complete.
Chapter 10: Performing extractions 209
NOTE: The duration varies depending on the extraction method, the device model, the amount of data on the device, the extracting computer, and other parameters.
The advanced logical extraction is saved to the selected location as a *.UFD file and a *.TAR file.
Open the advanced logical extraction in UFED Physical Analyzer to access all extracted information, including any deleted information.
NOTE: You cannot access extracted deleted information if you open the extraction in UFED Logical
Analyzer.
210
8) Select one of the following options:
Open in UFED Physical Analyzer Loads the extraction file in UFED Physical Analyzer.
Open file location Opens the folder that contains the extraction files.
Back to start Returns to the extraction methods screen.
Finish close iOS Device Extraction.
10.2. Extraction from GPS or mass storage devices
Extract and save data from a GPS device (Gamin, Mio, and TomTom) or a mass storage device.
NOTE: Only administrator users can read data from GPS devices. If you are not an administrator, close
UFED Physical Analyzer, right-click the UFED Physical Analyzer icon on your desktop, and select
Run as administrator.
1) Connect the GPS or mass storage device to your PC.
2) Select Extract > Extract GPS/Mass Storage Device, or click .
Chapter 10: Performing extractions 211
3) Select the device.
212
4) Do one of the following:
Enter the path where you want to save the data extracted from the device.
Click
5) Click Start.
, and browse to and select the desired location.
6) Select the type.
Chapter 10: Performing extractions
The extraction begins. When finished, the following message appears:
213
7) Click Yes to open the extraction.
10.2.1. Reading data from a GPS or mass storage device
Read and save data from a GPS device (Gamin, Mio, and TomTom) or a mass storage device.
NOTE: Only administrator users can read data from GPS devices. If you are not an administrator, close
UFED Physical Analyzer, right-click the UFED Physical Analyzer icon on your desktop, and select
Run as administrator.
1) Connect the GPS or mass storage device to your PC.
2) Select Tools > Dump GPS/Mass Storage Device, or click .
214
Chapter 10: Performing extractions
3) Select the device.
4) Do one of the following:
Enter the path where you want to save the data extracted from the device.
Click
5) Click Start.
, and browse to and select the desired location.
215
6) Select the dump type.
216
The extraction begins. When finished, the following message appears:
7) Click Yes to open the extraction.
Chapter 11: Advanced features
Chapter 11: Advanced features
217
11.1. Working with TomTom
TomTom generate trip log files that are encrypted by the device only if TomTom users select to share their location information with TomTom. TomTom registers the device location in the trip log files.
Export the TomTom XML file generated from the trip logs, and send it to Cellebrite for processing.
Once returned, you can view most of the location information available in the file using UFED Physical
Analyzer.
For more information on extracting data from a TomTom device, see
(page
).
For more information on geolocations, see
(page
).
NOTE: Not all the information contained in the TomTom extraction file is retrievable.
NOTE: The processing service can take up to a few days, depending on the volume of data and requests. The service is currently free of charge, but this may be subject to change.
NOTE: You must open the TomTom extraction in UFED Physical Analyzer before exporting or importing the XML file.
218
11.1.1. Exporting a TomTom file
1) Open an extraction from a TomTom device.
2) In the Tools menu, select TomTom > Export.
3) Browse to the location where you want to save the exported TomTom extraction file, and click
Save.
The TomTom extraction file is saved as a GPS.TomTomExport.xml file.
NOTE: The file does not contain personal user information such as locations.
4) Send the GPS.TomTomExport.xml file to: [email protected]. For US customers: [email protected].
Chapter 11: Advanced features 219
The GPS.TomTomExport.xml file is processed by Cellebrite support. Your request enters a queue at
Cellebrite support. Processing of the TomTom extraction file may take a few days.
11.1.2. Importing a TomTom file
Once Cellebrite support has returned your processed TomTom XML file, import the file to UFED
Physical Analyzer.
1) Open the TomTom extraction for which you have the *.xml file.
2) In the Tools menu, select TomTom > Import.
3) Click
Open.
and browse to the location of the returned TomTom extraction *.xml file, and click
4) Click Import.
220
The TomTom *.xml file is imported to UFED Physical Analyzer. The Locations tree item is populated.
5) Double-click Locations to open the tree item in a data tab.
The tab shows the device's location at every three seconds with a time and date stamp and geographical coordinates.
NOTE: Not all the information contained in the TomTom extraction file is retrievable.
11.2. Carving images
Perform image carving to retrieve jpeg image files or fragments that are incomplete or corrupt, signifying that they have been deleted by the user. Image carving retrieves the images and rebuilds them as much as possible.
Perform image carving on demand; carving is not performed when UFED Physical Analyzer opens the physical extraction.
NOTE: Image carving is only available for physical extractions.
Image carving is can take some time to process. While processing, you can work in parallel in UFED
Physical Analyzer.
Chapter 11: Advanced features
11.2.1. Scanning for carved images
1) Do one of the following:
Click .
221
NOTE: When you click in the toolbar, the scan applies to the active project, that is, the project that you last clicked in.
If you have not scanned for carved images in this session: double-click the Carving >
Images tree item.
If you have already scanned for carved images in this session: right-click the Carving >
Images tree item and select Scan again.
222
The Carve Images window appears.
Chapter 11: Advanced features 223
2) Select the Scan type:
Quick scan: This scan has three stages, where UFED Physical Analyzer tries to recover images that start with a full, partial, or corrupted header only.
Full scan: This scan has five stages, where in addition to recovering images that have a full, partial, or corrupted header, UFED Physical Analyzer tries to recover images from blocks of jpeg data that appear without any header information. A full scan takes longer than a quick scan, and potentially finds more images.
Full scan without filter: This scan uses the same Full scan algorithm without the false positive filter. It can be used to verify if images were missed, but it takes by far the longest time and causes additional false positives.
3) Select from where you want to carve the images:
Unallocated space: scan unallocated memory space.
Images: select all images that you want to scan.
4) Click OK.
The scan begins. Progress is shown next to the Carving > Images tree item.
224
11.2.2. Working with carved images
Open data display tabs for all the carved images, for individual carved images, and extract the images to your computer.
To view all the found images in the project tree
Click to expand the Carving > Images tree item.
To open a data display tab for an individual image:
Double-click the image in the project tree.
For more information on working with images, see
(page
).
To extract (dump) the carved images to your computer:
1) Right-click the Carving > Images tree item and select Dump.
2) In the Select Folder window, browse to the desired folder, and click Select Folder.
11.3. Verifying hash values
A hash value is a unique and compact representation of a piece of data, which can be used for integrity protection due to the fact that it is computationally improbable to find two distinct inputs that hash to the same value.
Chapter 11: Advanced features 225
Comparing a reference hash value that was generated during the extraction process for each binary extraction against their calculated hash values enables you to verify the integrity of the binary extractions you received.
To verify the hash values:
1) In the project Extraction Summary tab, do one of the following:
If hash information is available for the project, click Verify.
If hash information is not available for the project, click Calculate hashes.
The hash information is calculated or verified. If no reference data is available, a Hashes have been calculated for this project, but no reference data is available message is displayed in the Image
Hash Information section of the Extracted Summary tab.
2) Click Show Details.
226
The Image Hash Details dialog displays the comparison result of the reference and calculated hash values of each image.
indicates matching values.
indicates the images do not match.
Chapter 12: Working with hex data
Chapter 12: Working with hex data
227
The extraction enables you to view the device image, which is a single file or multiple files that contain a comprehensive copy of the contents and structure of the data on the device.
To access the hex view of the device image:
In the project tree, expand the Images tree item, and double-click the desired image.
228
An Image tab appears in the data display area showing the image data in Hex view.
Chapter 12: Working with hex data
Located under the Hex view tab are Analysis Information tabs that display the following types of information related directly to the displayed Hex data:
229
Values - A wide array of value interpretations, such as 8, 16, 32, and 64 bit, various string encoding, date & time formats, and more, calculated on the fly for the currently selected data in the Hex view.
See
(page
).
Bookmarks - A list of bookmarks added in the displayed Hex data. See
(page
).
Highlights - A list of content segments markups highlighted in the displayed Hex data. The
number of highlight results is shown in brackets next to the tab name. See
(page
).
Search - Displays results of a search in the displayed Hex data. A new search results tab opens for each search query performed. The number of results for each search is shown in brackets next to the tab name.
For more information on the Image tab, see
(page
).
230
12.1. Searching for information in the Hex data and decoded data
Chapter 12: Working with hex data
The Find window has several tabs that enable you to search the Hex data in the following modes:
231
Find - Search for specific parameters, such as strings, bytes, dates, and more.
RegEx (GREP) - Search for strings using Regular Expressions.
SMS 7Bit (PDU) - Search for SMS text strings.
Pattern - Search for text patterns, in cases in which the pattern of the text is understood but not the text itself (mainly used for 7 bit search to locate SMS messages).
Code - Specialized search for user codes and passwords.
NOTE: The Find modes were built using the Plug-ins architecture. The find options can be enhanced and extended by adding new search plug-ins.
For more information on targeted searches, refer to the following sections:
(page
)
(page
)
(page
)
(page
)
(page
)
(page
)
232
(page
)
(page
)
(page
)
12.1.1. Searching strings
Search for strings to locate different types of data in the Hex data, e.g. text messages, phone numbers, names or any other string data.
1) While viewing Hex data, click to open the Find window.
2) In the Find tab, select Strings from the data type list.
Chapter 12: Working with hex data
3) Select the type of text encoding to search for the given string:
ASCII
UNICODE (mainly for non-Latin characters)
UTF-8
7 bits (mainly for SMS text)
233
234
The Search parameters area appears.
4) In the Search parameters area: a) In the Term box in the String parameters area, enter the search string. b) Select the Case sensitive option, if necessary.
5) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3).
Chapter 12: Working with hex data
e) Select Show results comments to display
235
6) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data. f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
7) Click Find.
236
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
8) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
9) To search for specific data and filter the search results, use the Find box in the search results tab.
10) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
Chapter 12: Working with hex data
12.1.2. Searching bytes
237
Search for bytes to look for specific occurrences in the Hex data. This is especially useful when you know the identifying header of a file type or information you are looking for. For example, the starting
Hex bytes of a jpeg image are FF D8 FF. Therefore, the result of searching for FF D8 FF provides the locations of all possible jpeg image headers in the Hex data.
1) While viewing Hex data, click to open the Find window.
2) In the Find tab, select Bytes from the data type list.
238
3) Select Hex.
The Search parameters area appears.
4) In the Bytes (hex) box, enter the Hex value, for example, FFD8FF.
5) In the Options area, set the desired search options:
Chapter 12: Working with hex data
a) In the Search direction list, select the search direction.
239
b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
6) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for.
240
b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data. f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
7) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
Chapter 12: Working with hex data 241
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
8) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
9) To search for specific data and filter the search results, use the Find box in the search results tab.
10) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.3. Searching dates
Search for dates to find date ranges in the Hex data.
1) While viewing Hex data, click to open the Find window.
2) In the Find tab, select Dates from the data type list.
242
The filter box displays a list of date formats and plug-ins that can be used for date searches.
3) Select the desired date format(s) and any plug-in(s) that you want to use in the current search.
Chapter 12: Working with hex data 243
NOTE: What plug-ins are suitable depend on how the data is encoded, what type of device you are analyzing, and so on. If you select a plug-in that is not suitable, your search results may contain false results. For example, you can select BlackBerry if you are analyzing a BlackBerry device. If you are not analyzing a BlackBerry device, selecting BlackBerry may return results that are inaccurate.
The Search parameters area appears.
4) In the Min Date and Max Date fields, click to select a date from the calendar.
Tip: Set a short date range in order to reduce the number of given results.
Tip: When searching for a particular date, set the Min Date and Max Date fields to a range of not less than 24 hours.
5) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
244
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
6) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data.
Chapter 12: Working with hex data
f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
245
The additional data is logged to the Additional before and Additional after fields of search results.
7) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
246
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
8) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
9) To search for specific data and filter the search results, use the Find box in the search results tab.
10) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.4. Searching SIM ICCID numbers
This search method enables you to search for SIM ICCID numbers in the Hex data.
1) While viewing Hex data, click to open the Find window.
2) In the Find tab, select SIM from the data type list.
Chapter 12: Working with hex data
3) Select ICCID.
The Search parameters area appears.
4) In the Numbers sample configuration area, enter the ICCID number in the Number box.
247
248
5) If you entered only part of the number, select Allow Partial Match. For example, entering the number 89972 and selecting this option, UFED Physical Analyzer searches for ICCID numbers provided by an Israeli service provider.
6) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
Chapter 12: Working with hex data 249
7) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data. f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
8) Click Find.
NOTE: If the Number field is left empty, the search results include all the numbers that match the
ICCID format.
250
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
9) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
10) To search for specific data and filter the search results, use the Find box in the search results tab.
11) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
Chapter 12: Working with hex data
12.1.5. Searching SMS numbers
Search for SMS numbers in the Hex data.
1) While viewing Hex data, click to open the Find window.
2) In the Find tab, select Numbers from the data type list.
251
252
3) To perform a search of SMS PDU numbers, select SMS PDU numbers.
The Search parameters area appears. a) In the Number field, enter the search number.
NOTE: If the Number field is left empty, the search results include all the numbers that match the
SMS Number format. b) If you entered only part of the number, select Allow Partial Match.
4) To a search for reversed nibbles, select Reverse nibbles numbers.
NOTE: Use this option when the data has been encoded to include reversed nibbles.
The Search parameters area appears.
In the Nibbles field, enter the desired nibble.
5) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
Chapter 12: Working with hex data 253
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
6) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit).
254
e) Select Contains, and enter a string that the search result must contain in its additional data. f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
7) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Chapter 12: Working with hex data 255
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
8) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
9) To search for specific data and filter the search results, use the Find box in the search results tab.
10) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.6. Searching for regular expressions (GREP)
Search for regular expressions to (RegEx) in order to look for a specific string structure within the data.
[a-zA-Z0-9._%+-]+@[a-zA-Z0-9.-]+\.[A-Za-z]{2,4}
Physical Analyzer searches your data for all the email addresses that match the structure
<string>@<string>.<2 to 4 letters>.
1) While viewing Hex data, click to open the Find window.
256
2) In the RegEx (GREP) tab, enter the expression that you want to use in the search.
3) Click to enter a regular expression code from a list of common codes..
4) Click to save the current expression in the library list.
Chapter 12: Working with hex data 257
5) Click to clear the regular expression field.
6) Set the Maximum result length value to filter only results that are up to the specified length.
7) Select Ignore case to disregard the case in the search results.
8) Select Multiline.
9) To use a saved expression from the library, click it in the Library area.
10) To export the current regular expression library to a *.rel file, click .
11) To load an exported regular expression from a *.rel file, click .
12) To delete an expression from the library list, click
13) In the Options area, set the desired search options:
. a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
258
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
14) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data.
Chapter 12: Working with hex data
f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
259
The additional data is logged to the Additional before and Additional after fields of search results.
15) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
260
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
16) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
17) To search for specific data and filter the search results, use the Find box in the search results tab.
18) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.7. Searching SMS text strings
This search method enables you to search for SMS text strings (7bit PDU) in the Hex data
1) While viewing Hex data, click to open the Find window.
2) Select the SMS 7Bit (PDU) tab.
Chapter 12: Working with hex data
3) In the Text Options area, set the following search parameters: a) Set the search type: Letters only, Numbers only, or Both. b) To show unique results, select Unique results only. c) To allow symbols in the search results, select Allow symbols.
261
262
d) To show low match results, select Show low match results. e) To set the minimum number of characters in the results, set the Minimum length.
4) In the Type area, select the search type: Unicode, 7Bit, 7Bit reversed.
5) In the Advanced area, set the following, as applicable:
Maximum number of Upper/Lower case switches
Maximum number of Letter/Digit/Symbol switches
Minimum number of words
Space required every N chars
Maximum occurrences of the following characters
Contains the following words divided by spaces.
6) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Chapter 12: Working with hex data 263
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
7) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data.
264
f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
8) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Chapter 12: Working with hex data 265
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
9) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
10) To search for specific data and filter the search results, use the Find box in the search results tab.
11) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.8. Searching for patterns
When navigating within a large memory structure, the search for patterns to locate any content that is textual in nature.
1) While viewing Hex data, click to open the Find window.
2) Select the Pattern tab.
266
3) In the Text Options area, set the following search parameters: a) Set the search type: Letters only, Numbers only, or Both. b) To show unique results, select Unique results only. c) To allow symbols in the search results, select Allow symbols.
Chapter 12: Working with hex data
d) To show low match results, select Show low match results.
267
4) In the Minimal length and Maximal length fields, set the pattern length range.
This option enables you to filter the results according to the searched patterns.
5) In the Type area, select the search type: ASCII, Unicode, 7Bit and/or 7Bit reversed.
6) In the Advanced area, set the following, as applicable:
Maximum number of Upper/Lower case switches
Maximum number of Letter/Digit/Symbol switches
Minimum number of words
Space required every N chars
Maximum occurrences of the following characters
Contains the following words divided by spaces.
7) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
268
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
8) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value. a) Select Show before to show the data immediately before what you are searching for. b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data.
Chapter 12: Working with hex data
f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
269
The additional data is logged to the Additional before and Additional after fields of search results.
9) Click Find.
NOTE: Pattern search can be used to locate all possible 7 bit SMS text results. To minimize the number of false positive results set the Minimal Length value to a higher number.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
270
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
10) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
11) To search for specific data and filter the search results, use the Find box in the search results tab.
12) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.1.9. Searching for codes and passwords
Search large memory structures for user codes and passwords.
1) While viewing Hex data, click to open the Find window.
2) Select the Code tab.
Chapter 12: Working with hex data
3) In the Text Options area, set the following search parameters: a) Set the search type: Letters only, Numbers only, or Both. b) To show unique results, select Unique results only.
4) In the Minimal length and Maximal length fields, set the pattern length range.
271
272
This option enables you to filter the results according to the searched patterns.
5) In the Options area, set the desired search options: a) In the Search direction list, select the search direction. b) In the Search results window list, select New, Replace current, or Add to current, as desired. c) To set the Text and Background colors, click the color box, select the desired color, and click
OK.
The colors you set here are retained for the duration of this session. To change the default
colors, set the colors in the Setting window. For more information, see
(page
).
Tip: To easily distinguish between the given results of each search performed, set different text and background colors for each search you run. d) Do one of the following:
Select Find all instances to display all search results at the end of the process
Clear Find all instances to move through the found items one-by-one during the search
(can also be done by pressing F3). e) Select Show results comments to display
6) In the Additional data area, enhance your search capabilities by including a predefined number of characters before and/or after the searched value. This can help you locate specific results, or even limit the results to specific entities of the searched value.
Chapter 12: Working with hex data
a) Select Show before to show the data immediately before what you are searching for.
273
b) In the Offset box, enter the offset from the start of the search result from which to start including the additional data. c) In the Length box, enter the length of the additional data to include starting at the set offset point. For Show before, the Length cannot be longer than the Offset. d) In the Show as box, enter the data type for the additional data to be displayed (Hex, ASCII,
Unicode, or 7Bit). e) Select Contains, and enter a string that the search result must contain in its additional data. f) Select Show after to show the data immediately after what you are searching for, and repeat steps 2-5. g) For the Show after option, set whether the offset and length of the additional data are calculated From result start or From result end.
The additional data is logged to the Additional before and Additional after fields of search results.
7) Click Find.
If you selected Find All Instances in the Options area, the results appear in the Search results tab in the analysis information tab (in the Hex view tab).
If you did not select Find All Instances in the Options area, the next found instance is highlighted in the Hex View tab.
274
The Search results tab includes the following:
# - The instance number.
Offset - The address offset of the data file in the Hex data.
Length - The string length in bytes.
Value - The string itself.
Source
More
Additional before - If you set additional data options in the Find window, displays the data located immediately before the result.
Additional after - If you set additional data options in the Find window, displays the data located immediately after the result.
8) To display a result instance in the Hex view tab, click on the desired row in the search results tab.
9) To search for specific data and filter the search results, use the Find box in the search results tab.
10) To export the search results list, click the desired output in the Search tab toolbar: Excel , HTML
, PDF , or XML .
12.2. Browsing the hex extraction
Double-click on a binary hex extraction in the project tree to display its content in a Hex view tab in the data display area.
Chapter 12: Working with hex data
NOTE: You can also click the image links in the Extraction Log area at the bottom of the Extraction
Summary tab to access the Hex extraction.
275
12.3. Using an offset to jump to a different location in the file
Scan the Hex data by setting an offset value by which to jump through the data.
To move from a set position:
1) Click .
2) Select Decimal or Hex and in the Offset box, enter the offset value in the relevant format.
3) In the From area, set the reference point from which to set the offset (Beginning of file, Current position, or End of file).
4) Click Go.
The cursor moves to the offset location.
To move from the current location:
1) Click on a specific location in the Hex data.
2) In the offset value box in the toolbar, enter the desired offset value in decimal format (20) or Hex value format (0x20), or select one of the previously entered values from the list.
NOTE: Type + or - before the value to calculate the offset from the current position.
276
3) Do one of the following:
Click to jump backwards through the Hex data according to the set value.
Click to jump forwards through the Hex data according to the set value.
12.4. Working with bookmarks
A bookmark is a quick reference pointer you can create on Hex data.
The bookmarks you create are managed in the Bookmarks tree item. The number of bookmarks in the project is shown in brackets next to the Bookmarks tree item.
In the project tree, double-click Bookmarks to list the bookmarks in a tab in the data display area.
To print or export the entity bookmarks list, click the desired output in the Bookmarks tab toolbar:
Excel , HTML , PDF , or XML .
12.4.1. Adding a bookmark
1) While viewing Hex data, do one of the following:
In the Hex View tab toolbar, click .
To bookmark a specific segment in the Hex data, highlight the section that you want to bookmark, and then click in the Hex View tab toolbar.
In the Bookmarks tab, click .
Chapter 12: Working with hex data
The Add Bookmark dialog box is displayed.
2) In the Name box, enter a name for the bookmark.
3) In the Description box, enter a description for the bookmark.
277
278
4) If you did not highlight an area in the Hex, in the Location area, do the following: a) Select the desired unit for the address, Decimal or Hex, from the Base list. b) In the Address box, enter the address of the start point (offset) of the data you want to bookmark. c) In the Length box, enter the length of the data you want to bookmark.
5) In the Colors area, set the Background and Text colors for the bookmark.
6) Click OK.
The new bookmark is saved and displayed in the Hex view Bookmarks tab.
The marked segment is highlighted in the chosen colors. Details about the bookmark appear in the results window.
Each bookmark displays the following information:
Offset - The address offset of the bookmark paragraph in the Hex data
Length - The bookmarked data segment length
Description - The bookmark name
7) Click on a bookmark item in the Bookmarks list to display it in the Hex view.
Chapter 12: Working with hex data
12.4.2. Editing a bookmark
1) In the Hex view Bookmarks tab, click .
The Add Bookmark dialog box is displayed.
2) Change the bookmark as desired, and click OK.
12.4.3. Deleting a bookmark
In the Hex view Bookmarks tab, select the bookmark that you want to delete and click .
The bookmark is deleted.
279
12.5. Decoding raw data
Select segments of the Hex data and decode them to a variety of encoding types on the fly.
UFED Physical Analyzer can decode Hex data to 8 Bit, 16 Bit, 32 Bit, 64 Bit, Strings, Date & Time, Binary, and Numbers.
To decode segments of Hex data:
1) In the Hex View tab, select the segment of data that you want to decode.
2) In the Values tab at the bottom of the Hex view tab, scroll to the desired encoding, then click to expand the display.
280
NOTE: Some encoding options have sub-decoding categories.
3) Click or to expand or collapse all the encoding types.
4) To decode a different segment of data, select another segment in the Hex View tab.
The results in the Values tab change to reflect the selected segment.
12.6. Viewing the hex data information
Display the information of bookmarked segments and search results when you point to them in the
Hex View tab.
Chapter 12: Working with hex data
1) In the Hex View tab toolbar, click .
2) Position the mouse over bookmarked information or search results in the Hex.
The floating information frame appears.
281
The following information includes:
Links (pointers) to analyzed data items such as files and folders in the project tree.
Search results associated with the pointed data.
3) To edit the bookmark, click .
4) To copy the data, click .
The data is copied to the clipboard.
5) To pin the information frame open, click .
The information frame remains open and displays the information for the last segment that you point to. The information displayed in the frame is automatically updated when you point to a different bookmarked segment or search result.
6) To close the information frame, click .
282
12.7. Locating specific data types in the Hex
The Highlights tab presents analyzed data locations within the Hex data, enabling you find the exact location(s) of a particular type of analyzed data in the Hex data.
1) Access the Highlights tab at the bottom section of the Hex view.
2) In the project tree, select one of the Analyzed Data folders, for example, Contacts.
The selected folder is highlighted in the Hex View tab; the Highlights tab lists the chunks in the selected folder.
3) To export the Highlights list, click the desired output in the Search tab toolbar: Excel , HTML ,
PDF , or XML .
Chapter 13: Camera and screenshot evidence
Chapter 13: Camera and screenshot evidence
283
UFED 4PC or UFED Touch together with the UFED camera enables you to collect evidence by taking pictures or videos of a device. A screenshot feature captures internal screenshots directly from a
Blackberry, Android or iOS device. These options can be useful as complimentary evidence or in instances when data cannot be extracted from a device. This evidence can be displayed in UFED
Physical Analyzer together with any notes, categories and bookmarks, which were added by the examiner. For information on capturing camera and screenshot evidence, refer to the
UFED 4PC
or
UFED Touch
user manuals.
To import camera or screenshot evidence:
Click the Evidence.ufd file.
The Camera Evidence (pictures and videos) or Phone Evidence (screenshots) is imported into
UFED Physical Analyzer as a new project. The evidence includes Phone Evidence or Camera
Evidence divided by category, as well as entity bookmarks and notes that were added during the extraction. An example is displayed next.
284
Chapter 13: Camera and screenshot evidence
To import camera and screenshot evidence together with the extracted data:
Click the EvidenceCollection.ufdx file.
285
The Camera Evidence (pictures and videos), Phone Evidence (screenshots) and the extracted data are imported into UFED Physical Analyzer as a single project. The evidence includes Phone
Evidence and Camera evidence, as well as categories, entity bookmarks and notes that were added during the extraction. An example is displayed next.
286
NOTE: Drag-and-drop the EvidenceCollection.ufdx file into UFED Physical Analyzer to open multiple extractions, which were performed for a particular device. That is, all extractions in the folder will be opened. Each extraction (.ufd file) in the folder can also be opened separately. An example folder with multiple extractions and a UFDX file is displayed next.
To associate camera and screenshot evidence with an extraction type:
If you have multiple extraction types as well as camera evidence, the Associate evidence with project screen appears.
Select the required extraction and click Associate.
Chapter 14: Advanced decoding
Chapter 14: Advanced decoding
287
14.1. Managing chains
A chain is a set of plug-ins grouped together, which is used to process the extracted data of a device.
Each device in the supported devices list of the application has a predefined parsing chain assigned to it.
As part of its building blocks, a chain can also include other predefined chains.
Use the Chain Manager to:
Manage and edit existing chains
Create new chains
Assign chains to devices
To manage application chains:
1) Do one of the following:
In the Plug-ins menu, select Chain Manager.
Click .
288
The Chain Manager window appears.
Chapter 14: Advanced decoding
The Chains list on the left enables you to filter the displayed chains list.
289
2) Click My Chains to display your custom chains.
3) Click All Chains to display a list of all the predefined chains.
4) Use the Quick Filter box at the top left of the window to filter the displayed list of chains.
5) To display the chains assigned to a specific device, from the Devices section of the list, select one of the following:
All Devices to display a list of all the predefined devices.
A manufacturer name to display a list of the predefined devices of the selected manufacturer.
6) Double click on a device to display its chains window.
The chains window of the device displays at least one chain that was assigned to it.
14.1.1. Constructing a new chain
1) In the Chain Manager window, click New Chain.
2) Click New Chain.
290
The New Chain window appears.
3) Click New Chain at the top of the window, and enter a name for the chain.
4) In the Description box, enter a short description for the chain (optional).
Chapter 14: Advanced decoding
5) From the Component Library, select a components category:
Plugins - Specific plug-ins.
Chains - Specific predefined chains.
Devices - Entire chain of a specific plug-ins.
NOTE: Devices and Chains are added to the chain as a chain component.
291
6) To add a component to your chain list, click next to the component.
7) To remove a component from the chain list, click at the right of the component item, then click
Yes to approve.
8) To edit the parameters of a plug-in or chain, select it from the chain components list (on the left) and set the options displayed.
NOTE: To return to the Component Library display and continue adding more plug-ins and chains, click Add Chain/Plugin.
9) When finished, click Save.
The new chain is added to your My Chains list.
14.1.2. Editing an existing chain
1) Edit chains that you have created.
2) In the Chain Manager My Chains list, double-click the chain you wish to edit.
3) Click Add Chain/Plugin to display the Component Library.
292
4) To add a component to your chain list, click next to the component.
5) To remove a component from the chain list, click at the right of the component item, then click
Yes to approve.
Chapter 14: Advanced decoding 293
6) To edit the parameters of a plug-in or chain, select it from the chain components list (on the left) and set the options displayed.
NOTE: To return to the Component Library display and continue adding more plug-ins and chains, click Add Chain/Plugin.
294
7) When finished, click Save, or Save As to save the edited chain as a new chain.
8) If you selected Save As, enter a name for the new chain and click Save.
NOTE: Changes made to factory predefined locked chains can only be saved as a new chain
14.1.3. Managing device chains
14.1.3.1. Attaching devices to a chain
You can attach devices to chains you have created, or modify device chains and save them as a copy.
1) Double-click the chain to which you want to attach a device.
2) Click Edit Devices.
Chapter 14: Advanced decoding
3) In the Devices For Chain window, click Attach Device.
295
296
4) In The Select Device window, select the device you would like to attach to the chain.
Chapter 14: Advanced decoding
5) Click Select.
6) Repeat steps 3-5 to add more devices.
7) When you have finished attaching the devices, click Save.
14.1.3.2. Setting the default device chain
1) In the Chain Manager window, use the Devices list to locate the device you wish to modify.
2) Double-click on the device to display its chains window.
297
298
3) If the chains list of the device contains more than one chain, click to set it as the default chain of the device.
4) Click Close to close the device chains window.
Chapter 14: Advanced decoding
14.1.3.3. Detaching devices from a chain
1) Double click on the chain from which you wish to detach a device.
2) Click Edit Devices at the top right of the chain window.
299
300
3) Click at the right of every device you wish to detach from the chain.
4) Click Close.
5) Click Cancel to close the chain window.
14.1.4. Removing a chain
You can remove chains from the My Chains list only.
1) In the Chain Manager window, select My Chains.
2) Click at the right of the chain.
14.1.5. Chain descriptions
The following table lists selected UFED device chains and descriptions.
Chain name Description
AndroidContent
Decodes content for Android file systems
AndroidContent Japanese
Decodes content for Android file systems and Japanese apps
AndroidFS
Decodes different file systems on Android. This is part of Motorola
Android or AndroidDD chains
AndroidDD
Decodes certain types of Android devices using the metadata from the extraction
Chapter 14: Advanced decoding
Chain name Description
AndroidDD Japanese
AndroidiDen
Decodes certain types of Android devices and Japanese apps using the metadata from the extraction.
Decodes Motorola iDen with Android operating system physical extractions
Decodes content for Android logical extractions
Android Logical with
Content
AndroidMotorolaYaffs
AndroidMTK NAND
AndroidNvidia
AndroidSamsungFAT
BlackBerryIPD
BlackBerry Physical
BlackBerryBackup
CasioC700Content
Decodes Motorola Android device (AndroidDD) extractions
Decodes NAND extractions of MTK Android devices
Decodes Android devices with an Nvidia chipset
Decodes various Samsung Android phones with FAT file systems
Decodes BlackBerry backup devices using Cellebrite's default chain
Decoding BlackBerry physical and/or file system extractions
Decodes BlackBerry backup extractions
Decodes models for the Casio c7X1 series
Generic FAT iCloudBackup
Decodes FAT (file allocation table) system
Decodes data from Apple iCloud backup
iPhone Japanese Content
Decodes content for Japanese iPhones
iPhone Databases Logical
Decodes iPhone content for logical extractions
iPhoneBackupLogical iPhoneFS iPhonePhysical
Motorola Android
Decodes data from iPhone backups for logical extractions
Decodes iPhone file systems and content
Decodes Physical iPhone extractions
Decodes Motorola Android devices
301
302
Chain name Description
Nokia FS
Nokia Content
Nokia Predef XSR
Decodes Nokia file systems
Decodes all Nokia content
Decodes non Symbian Nokia BB5 physical extractions
PantechCdm8999Contents
Decodes SMS, MMS and call logs for the Pantech CDM8999 device
QCAndroid
Decodes Qualcomm Android physical extractions
Qualcomm Winmobile
Decodes the flash translation layer of LG Windows mobile and extracts files and SMS from the file system
Decodes reports into UFED Physical Analyzer
Report
Samsung Qualcomm with
Content
Sanyo Qualcomm CDMA
Physical
Symbian Physical
WebOS
Decodes file system and content from Samsung Qualcomm devices
Decodes the flash translation layer file systems and content of Sanyo
CDMA devices with a Qualcomm chip
Decodes the flash translation layer and a FAT partition using Symbian
Decodes file systems for Web operating system devices (Palm)
WindowsPhone7
Decode extractions of Windows Phone 7 devices
AndroidXSR
Decodes Android devices with the XSR flash translation layer
BlackBerry Filesystem
Content
Decodes data from BlackBerry file systems
Android Samsung Nexus
Decodes Samsung Nexus devices
AndroidMTK MMC
Decodes MMC extractions of MTK Android devices
Chapter 14: Advanced decoding 303
Chain name
Samsung Non Android
Content
Nokia Predef Content
HTC Generic JTAG
Decodes content of Samsung devices that are not running Android operating systems
Decodes content of Nokia Predef devices
Samsung MCUv2 - No
MMS, Phonebook
Decodes MCUv2 devices excluding MMS and phonebook
Samsung Qualcomm JTAG with Content
Decodes file system and content from JTAG extractions of Samsung
Qualcomm devices.
Windows Mobile XSR JTAG
Decodes JTAG extractions of Windows mobile devices with the XSR flash translation layer
SIM Card FS
Decodes content from file system extractions of SIM cards
LG Qualcomm JTAG with
Content
Sanyo Qualcomm JTAG with Content
Samsung Generic JTAG
Decodes file system and content from JTAG extractions of LG
Qualcomm devices
Decodes content from JTAG extractions of Sanyo CDMA devices with a Qualcomm chip
Decodes the extraction in all supported methods for Samsung devices
Decodes the extraction in all supported methods for HTC devices
Samsung Qualcomm with
SMS iPhone Logical with
Content
Description
Decodes file system and SMS from Samsung Qualcomm devices
Decodes iPhone logical report extractions
304
14.2. Plug-ins
The Plug-ins mechanism is an API that allows users to expand the abilities of the application by adding plug-ins provided by Cellebrite, or custom tailored plug-ins written using Python.
14.2.1. Managing plug-ins
The Add/Remove Plugins window enables you to manage the installed plug-ins.
1) Click .
Chapter 14: Advanced decoding 305
2) To display all the installed plug-ins, including the built-in plug-ins that cannot be removed, select
Show built-in plug-ins.
Perform the following tasks in the Add/Remove Plugins window:
3) To install additional plug-ins, drag them to the Add/Remove Plugins window.
4) To extract a copy of an installed plug-in, select the plug-in and click Extract Plugin.
5) To remove an installed plug-in, select the plug-in and click Uninstall.
306
NOTE: You cannot extract or uninstall a built-in plug-in of the application.
6) To display the plug-in status, double-click the plug-in.
The Plug-in Status dialog displays the status of the plug-in, which can be either signed or unsigned.
A signed plug-in is a plug-in that was approved and signed by Cellebrite.
14.2.2. Running a specific plug-in
1) Run an individual plug-in on your project.
2) In the Plug-ins menu, select Run Plug-in.
Chapter 14: Advanced decoding
3) Select the desired plug-in from the list of plug-ins, and click Run.
307
308
14.3. Using the Python Shell
The built-in Python Shell enables you to run customized decoding and analysis using Python commands.
To open the Python Shell window, do one of the following:
1) In the Python menu, select Python Shell.
2) Click .
For additional information on how to use Python Shell commands for custom analysis, refer to the
"Python Scripting Guide", accessible from the Help menu.
Chapter 14: Advanced decoding
14.4. Exporting the file system
309
Export the extracted file system to save the entire file system to the selected location on your computer. The save provides the physical files and folders structure saved in the same hierarchy as the original file system.
To export the extracted file system:
1) In the Tools menu, select Dump file system, or click .
2) In the Browse For Folder dialog, select the target location to which to save the extracted file system.
3) Click Make New Folder to create a new folder in the target location.
4) Click OK to export the file system.
14.5. Using the Android unlock pattern carver plug-in
Use the Android Unlock Pattern Carver plug-in when working with Android devices where decoding is not yet supported.
The Android Unlock Pattern Carver plug-in can decode unlock patterns on Android devices. The plug-in can be executed on the image file created by the UFED device, JTAG, chip-off, or other tools for which decoding is not yet supported. The image file can be all device partitions, or the user data partition only.
1) Perform physical extraction using the UFED device.
310
2) In UFED Physical Analyzer, open the Android physical extraction either by dragging and dropping, or by using Open Advanced option.
3) Run the Android Unlock Pattern Carver plug-in. For more information on running a plug-in, see
(page
).
The unlock pattern is presented in the Extraction Summary tab Device Info area.
4) Unlock the Android device, and perform a physical or file system extraction using the UFED device.
14.6. Android unlock password carver plug-in
UFED Physical Analyzer includes the Android Unlock Password Carver plug-in. The plug-in, developed by the CCL Forensics group and integrated into UFED Physical Analyzer by Cellebrite, attempts to extract the unlock passwords from android extractions. The plug-in can be found in the standard plug-ins list.
Chapter 15: Settings
Chapter 15: Settings
311
The Settings window provides a set of functional and behavioral setup options used to fine-tune and control the functionality and usability of the application. The settings in the Settings window apply to all the projects open in UFED Physical Analyzer.
NOTE: Changes to settings are lost when you close UFED Physical Analyzer. To save the settings
configuration, see
(page
).
To access the Settings window, do one of the following:
Select Tools > Settings.
Click .
The Settings window appears.
312
15.1. General settings
Set general application settings in the General Settings tab.
To set the interface language of UFED Physical Analyzer:
In the Language list, select the desired language.
Chapter 15: Settings 313
To set the translation language:
1) Select the Translation Language. That is the language to which you want to translate the text. You can only select one Translation Language. To request additional translation languages, select Get more languages.
2) Select the Show translation language by default check box to display translations by default.
Clear this check box so that the translation will not appear when you translate text. To see the translation select View translated.
To shift timestamps to a particular time zone:
1) From the Time zone settings (UTC) list, select:
Original UTC value to show time stamps as recorded (without unification)
One of the time zones (UTC -12:00 to UTC +13:00) to recalculate network-defined time stamps according to the time zone offset.
2) To change the start and end dates for daylight saving time, click Daylight Saving Time. For more
information on how to change the time zone settings, see
(page
)
.
To set how deleted files are handled when using the Dump GPS / Mass Storage Device feature:
1) In the Dump area, select Save deleted files to save deleted files.
To set how deleted files are handled when using the Dump GPS / Mass Storage Device feature:
2) In the Dump area, select Save deleted files to save deleted files.
3) Select Add '.DEL' extension for deleted files to save deleted files with the *.DEL extension.
314
To set the encoding and separator of exported CSV files:
1) In the Export area, select the desired encoding option from the Encoding list.
2) Select the desired separator in the Separator list.
To set UFED Physical Analyzer to automatically verify images on project load:
Select Automatically verify images on project load.
To have UFED Physical Analyzer offer to load a session when opening its corresponding extraction:
Select Suggest restoring a session file when its corresponding dump is loaded .
To disable information highlighting:
Select Disable highlight information.
To select all entities in all views by default:
Select Check all entities by default.
Selected entities are included in reports that you generate.
To determine the number of digits required for phone number uniqueness:
In the Analytics area, select the desired number of digits from the Number of digits to determine phone number uniqueness.
Chapter 15: Settings
15.2. Data files
315
The Data Files settings determine the different file and tagging groups under the Data Files and Tags tree items, and the types of files filtered in each group.
Every data file record contains the following settings:
316
Active - Indicates whether to display (checked) or hide (unchecked) this group of data files in the project tree.
Description - A descriptive name for the type of data files to be used as the group name under the
Data files tree item.
Extensions - The file extensions to be used to filter the data files of this group.
Signature filter - The header and/or footer signatures to be used to filter the data files of this group.
Tag As - The tag name to be applied to the data file and used to list the files under Tags in the project tree.
15.2.1. Data files filtering methods
Groups can be filtered using one or more of the following methods:
Signature filter
A signature filter is a definition of the file header and/or footer to be searched, in order to detect a file type and associate it with a specific Date File group. The header and/or footer can be configured in a defined range from the beginning and end of the file respectively by using the offset parameter.
Chapter 15: Settings 317
For example, a JPEG image starts with the header FF D8 FF and ends with the footer FF D9. Entering this information in the Header and Footer fields of the signature creates a signature that identifies
JPEG images.
Extension filter
An extension filter is a list of common file extensions that are associated with file formats that belong to the specific data file group.
For example, the different image file formats can be filtered by the file extensions *.jpg, *.jpeg, *.gif,
*.png or *.bmp.
15.2.2. Managing data files settings
Add new types of data files, and edit and delete existing data file types.
15.2.2.1. Adding a new data file type
1) In the Data Files settings, click .
A new row is added to the list.
2) Select Active to display the added data type in the Data Type tree item.
3) Click in the new row's Description box, and type a file type description.
318
4) If applicable, in the Extensions box, enter the file extensions commonly used by your data file type in the format *.xxx, and separated by ;.
5) If applicable, in the Signature filter box, click and do any of the following:
Click
Click
to add a filtering signature that identifies your data file type.
to edit an existing signature filter.
Chapter 15: Settings 319
Click to delete a signature filter.
6) If applicable, click in the Tag As box, click and select a tag name from the list.
7) To change the order of the data file types, use the arrows .
8) To clear the list of data file types you added, leaving only the default types, click Restore default.
15.2.2.2. Editing an existing data file record
1) Click the row of the data file type that you want to edit.
2) Double-click in the column and row that you want to change, and update the existing settings as desired.
15.2.2.3. Deleting a data file type
1) Click the row of the data file type that you want to delete.
2) Click .
320
15.3. Hex viewer settings
The Hex Viewer setting enables you to control the display options of Hex extractions to suit personal preference and enhance readability.
Chapter 15: Settings
Change the defaults for the following Hex viewer settings:
321
Show address - Show/Hide the line numbers column of the Hex Viewer.
Show ASCII view - Show/Hide the ASCII view column of the Hex Viewer.
Draw separation lines - Show/Hide the separation lines between the address, Hex data, and ASCII view columns
Display 0x00 and 0xFF string data as space - Set the string data to display both 0x00 and 0xFF
Base format for selection - The line numbers format (Decimal, Hex, or Both).
Font - The font used to display the information.
Color settings - Set the colors applied to different features of the Hex viewer.
322
15.4. Models settings
Set the color schemes to be applied to various types of device data.
1) In the Type list, select the data type.
2) In the Background color list, select the desired background color.
3) In the Text color list, select the desired background color.
Chapter 15: Settings
15.5. Additional report fields
323
Optional information is user-defined information presented at the beginning of the report. It usually includes information about the case, investigator, and organization details.
Every optional information record consists of the following:
324
Name
Required
Type
Default value
The name of the report field.
Indicates if the field must be filled in order to generate the report
The types of entry - String or List.
Default content.
You can add new report fields, and edit and delete fields, as desired.
15.5.1. Adding a new report field
1) Click Add New.
A new row is added to the table.
2) In the Name column, enter the name label to be displayed.
3) Select Required if this field must be filled in order for the user to generate the report.
4) In the Type list, select one of the following:
String for text entry fields
List for a specified list of options
5) In the Default Value box, set the default content:
Chapter 15: Settings
For String type, type the default string. For a multi-line string, click default string in the Option Editor, then click Save.
, enter the
325
For a List type, click click Save.
, enter the list items with each item on a separate line, then
326
15.5.2. Editing a report field
To edit a report field, perform steps 2-5 of
(page
), changing the
parameters to suit your needs.
15.5.3. Deleting a report field
To delete a report field, click .
15.6. Report defaults
The Report Defaults settings enable you to edit the report presentation.
Chapter 15: Settings 327
NOTE: Scroll down to see all the fields.
1) In the Report type list, select the report type that you want to edit.
2) For Excel reports, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting
328
order (ascending or descending) that was set by the user in each of the data display tables.
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
Unprintable characters placeholder - Set the placeholder character to replace the unprintable characters.
Output File Format - Set the output file format of the spreadsheet file to either:
* XLSX - The current Excel file format.
* XLS - The legacy file format of Excel.
* ODS - The spread file format of OpenOffice.
The excel report is compatible with OpenOffice - Select to ensure the Excel report can be opened in OpenOffice.
Generate Contact Identification Data - Select to add a sheet to the Excel report that provides a list of unique contacts based on type.
3) For HTML reports, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting
Chapter 15: Settings 329
order (ascending or descending) that was set by the user in each of the data display tables.
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
Disable models categorization - Select to disable the separation and generate a report in which every data items is generated as a single section without subcategories separation. By default, a categorized report in which each category in the data items group is generated as a separate section in the report is generated. For example, when generating a report with SMS, select the check box to generate the SMS messages as a single list, or clear the check box to break it to a separate list for each category of SMS messages (Inbox, Outbox, Drafts, etc.).
Logo Header - Enter and format custom text to appear in the report header before the logo image.
Logo - Click Select Image File to add the logo image to appear in the report header.
Supported file formats are: BMP, JPG, GIF, and PNG.
Logo Footer - Enter and format custom text to appear in the report footer after the logo image.
Show totals for items not in the report - Add a Total column to the report that displays the total number of items that were excluded from the report.
330
Show extended deleted state - Include the state (Intact, Deleted, or Unknown) of deleted items in the generated report. When not selected, logs only the state of deleted items as Yes, and is left empty for other states.
Number of lines for email preview - Set the maximum number of lines from each email message to appear in the report.
Display full email body - Display the entire message body.
Number of messages per chat - Set the maximum number of lines per chat message to appear in the report.
Display all chat messages - Display all chat messages in the report.
Split HTML report - Set each section of the report to start on a new page.
4) For PDF reports, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting order (ascending or descending) that was set by the user in each of the data display tables.
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
Chapter 15: Settings 331
Disable models categorization - select to disable the separation and generate a report in which every data items is generated as a single section without subcategories separation. By default, a categorized report in which each category in the data items group is generated as a separate section in the report is generated. For example, when generating a report with SMS, select the check box to generate the SMS messages as a single list, or clear the check box to break it to a separate list for each category of SMS messages (Inbox, Outbox, Drafts, etc.).
Logo Header - Enter and format custom text to appear in the report header before the logo image.
Logo - Click Select Image File to add the logo image to appear in the report header.
Supported file formats are: BMP, JPG, GIF, and PNG.
Logo Footer - Enter and format custom text to appear in the report footer after the logo image.
Show totals for items not in the report - Add a Total column to the report that displays the total number of items that were excluded from the report.
Show extended deleted state - Include the state (Intact, Deleted, or Unknown) of deleted items in the generated report. When not selected, logs only the state of deleted items as Yes, and is left empty for other states.
Number of lines for email preview - Set the maximum number of lines from each email message to appear in the report.
Display full email body - Display the entire message body.
Number of messages per chat - Set the maximum number of lines per chat message to appear in the report.
332
Display all chat messages - Display all chat messages in the report.
5) For UFED report packages, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting order (ascending or descending) that was set by the user in each of the data display tables.
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
6) For Word reports, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting order (ascending or descending) that was set by the user in each of the data display tables.
Chapter 15: Settings 333
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
Disable models categorization - Select to disable the separation and generate a report in which every data items is generated as a single section without subcategories separation. By default, a categorized report in which each category in the data items group is generated as a separate section in the report is generated. For example, when generating a report with SMS, select the check box to generate the SMS messages as a single list, or clear the check box to break it to a separate list for each category of SMS messages (Inbox, Outbox, Drafts, etc.).
Logo Header - Enter and format custom text to appear in the report header before the logo image.
Logo - Click Select Image File to add the logo image to appear in the report header.
Supported file formats are: BMP, JPG, GIF, and PNG.
Logo Footer - Enter and format custom text to appear in the report footer after the logo image.
Show totals for items not in the report - Add a Total column to the report that displays the total number of items that were excluded from the report.
Show extended deleted state - Include the state (Intact, Deleted, or Unknown) of deleted items in the generated report. When not selected, logs only the state of deleted items as Yes, and is left empty for other states.
334
Number of lines for email preview - Set the maximum number of lines from each email message to appear in the report. The report includes links to text files containing the entire email.
Display full email body - Set to display the entire message body.
Number of messages per chat - Set the maximum number of lines per chat message to appear in the report.
Display all chat messages - Display all chat messages in the report.
7) For XML reports, set the following:
Default folder - enter the path to the folder where you want to save reports you generate for this report type.
Select Default sorting to set sort the items included in the generated report according to the default sorting set by Cellebrite for each of the Analyzed and Data file types or clear
Default sorting to sort the items according to the selected sorting field and the sorting order (ascending or descending) that was set by the user in each of the data display tables.
Calculate SHA-2 (256 bit) hash and Calculate MD5 (128 bit hash) - Select which calculated MD5 and SHA256 hash keys to add to each Data Files item in the generated report. Do not select these options to shorten the report generation process of large projects.
Include translations Select to include any translated text in the report.
Chapter 15: Settings
15.7. Post-chain plugin settings
335
Add and remove plug-ins from the list of plug-ins that automatically run when you open a project.
This can be useful when you have time constraints or large extraction files. These settings enable you to define whether or not to run certain plug-ins.
336
1) To add a plug-in to the list, click Add Plugins and select a plug-in from the list.
2) To remove a plug-in from the list of plug-ins that run automatically when you open a project, clear the check box in the Enabled column.
3) To remove a plug-in from the list, select the plug-in and click Remove Plugins.
4) To filter the plug-ins list, use the Filter box.
NOTE: The settings apply to subsequent projects opened in your current session. To save your
configuration settings for use in subsequent sessions, see
(page
).
15.8. Saving settings
Save your settings to reuse later, or to share with another user.
1) In the Settings window, click Save Configuration.
2) In the Save As window, browse to the location where you want to save your settings configuration, and click Save.
The settings are saved as a UFED Physical Analyzer Settings Configuration File (*.cnf).
Chapter 15: Settings
15.9. Loading settings
337
Load your saved settings configuration.
1) In the Settings window, click Load Configuration.
2) In the Open window, browse to the location where your settings configuration is saved, select the configuration (*.cnf), and click Open.
The settings are applied in the Settings window.
15.10. Setting project settings
Set unified time zone and case information for each project.
15.10.1. Setting a unified time zone for the project
During extraction, one time stamp per event is extracted.
For outgoing events, the time stamp is typically taken from one of the following sources:
User-defined device time (where the device time has been manually set by the user: timestamps are displayed without the unified time (UTC).
Network-defined device time (where the device time is automatically set by the network): timestamps are displayed with the unified time (UTC).
338
For incoming events, the time stamp is typically taken from the network-defined time (the time stamp assigned by the network); timestamps are displayed with the unified time (UTC).
Network-defined time stamps are subject to the time zones in which the event occurred.
Apply a unified time zone to the project to recalculate all network-defined time stamps according to the selected time zone in order to consolidate the events and view them sequentially in UFED
Physical Analyzer.
To apply a unified time zone to the project:
1) Do one of the following:
In the project Extraction Summary tab, click Project settings.
Click .
Chapter 15: Settings 339
2) From the Time zone settings (UTC) list, select:
Original UTC value to show time stamps as recorded (without unification)
One of the time zones (UTC -12:00 to UTC +13:00) to recalculate network-defined time stamps according to the time zone offset.
NOTE: User-defined time stamps are not included in these recalculations, and are displayed as recorded.
3) To change the start and end dates for daylight saving time, click Daylight Saving Time.
340
Chapter 15: Settings 341
a) For the year that you want to change, use the calendar to select the start and end dates, or edit the dates directly. You can use the button to remove certain years. b) Click Back to last saved data to reset the table to the last time that you saved the data, click
Back to original data to return the table to its default settings, or click Save to save the table with any changes that you made.
4) Click OK.
The project is recalculated according to the selected unified time zone, and the new time zone is applied to the network-defined time stamps. Time stamps of events displayed in UFED Physical
Analyzer windows and any subsequently-generated reports reflect the selected unified time zone.
15.10.2. Setting the case information
Case information settings are saved with the project. The case number appears with the extraction information on the Welcome tab.
1) Do one of the following:
In the project Extraction Summary tab, click Project settings.
Click .
2) Click Case Information.
342
3) Click Add New.
Some case information fields appear by default.
4) Set the parameters for the default information fields: a) In the Name column, enter the relevant information (for example, case number, name, or notes). b) Select Required if this field must be filled. c) In the Type list, select one of the following:
String for text entry fields
List for a specified list of options
Chapter 15: Settings
d) In the Default Value box, set the default content:
343
For String type, type the default string. For a multi-line string, click
, enter the default string in the Option Editor, then click OK.
For a List type, click
, enter the list items with each item on a separate line, then click
OK.
5) To add more information fields, click Add New, and repeat step 3.
6) To remove the custom entries, click .
7) To restore the default settings, click Restore default settings.
344
Chapter 16: Reference
Chapter 16: Reference
16.1. File menu
Open
Open (Advanced)
Recent
Close
Save Project Session
Load Project Session
Exit
Open a file for analysis using the standard analysis process.
Open a file for analysis using the advanced analysis process. See
(page
.
Displays a list of recent projects.
Closes the currently active project
Saves the active project information generated by the user as a
Physical Analyzer Session File (*.pas). See
(page
).
Loads a Physical Analyzer Session File (*.pas) onto an open project in the project tree.
Closes the UFED Physical Analyzer and all active sessions.
345
346
16.2. View menu
Show Welcome Screen
Trace Window
Displays the Welcome tab. See
(page
.
Show/hide the trace panel at the bottom of the data display area.
16.2.1. Viewing the trace window
Show the Trace window at the bottom of the data display area to view a log of the actions performed in your session by you or by UFED Physical Analyzer, such as plug-in activation.
1) In the View menu, select Trace Window.
The Trace window appears below the data display area.
Chapter 16: Reference
2) To clear the log, in the Trace window, click Clear.
3) To close the Trace window, click .
The Trace window can be hidden or displayed.
To pin the Trace window open, click .
To unpin the Trace window, click .
To view the Trace window when hidden, select or mouse over the tab.
347
348
16.3. Tools menu
Read Data from UFED
Dump File System
Carve Images
Carve Strings
Enables data extraction directly to the computer.
Exports and saves the parsed file system to actual files and folders in
a directory structure. See
(page
).
Opens the Carve Images window from where you can scan for
images. See
(page
).
Opens the Carve Strings window from where you can scan for strings.
Watch List Editor
Malware Scanner
Translation
Opens the Watch List Editor, from where you can create, manage,
and run your watch lists. See
(page
).
Opens the Malware Scanner sub-menu, from where you can run malware detection on your extraction, and update the signature
database. See
(page
).
Downloads the translation pack from the Internet, installs the translation pack from a file, or displays the supported languages. See
(page
).
Open in UFED Link Analysis Open this Physical Analyzer project in UFED Link Analysis.
TomTom Opens the TomTom sub-menu, from where you can export the
TomTom extraction file and import the returned xml file. See
(page
).
Settings
Access the application settings window. See
(page
).
Chapter 16: Reference
Project Settings
349
Set unified time zone and case information for each project. See
(page
).
16.4. Extract menu
iOS Device Extraction
Extract GPS/Mass Storage
Device
Starts iOS Device Extraction to perform extractions from iOS devices.
See
(page
).
Reads and saves data from GPS and mass storage devices
connected to the workstation via USB connection. See
(page
.
16.5. Python menu
Python Shell Opens the Python Shell window for user customer analysis using
Python commands. See
(page
. For additional information on how to use Python Shell commands for custom analysis, refer to the "Python Scripting Guide", accessible from the Help menu.
Run Script Runs a pre-written Python script (*.py file).
Run Script (Debug enabled) Enables you to run a pre-written Python script (*.py file) in debug mode.
350
16.6. Plug-ins menu
Add/Remove Plug-ins Displays the list of pre-installed plug-ins to enable management of
the currently installed plug-ins. See
(page
).
Run Plug-in
Enables the user to select a specific plug-in and run it. See
(page
).
Chain Manager Displays the Chain Manager window to enable management and
creation of device processing chains. See
(page
).
16.7. Report menu
Generate Report Generates a report summary of all information found by the analysis process. See Generating a report.
Chapter 16: Reference
16.8. Help menu
Supported Apps Lists the supported applications and verified versions for Android and iOS devices.
Opens the user manual in PDF format. Manual
Python Shell Scripting
Guide
Opens the Python Scripting Guide in PDF format.
Activate Online Bing Maps Activates Bing maps so that you can view locations on a map. It requires Internet access and a valid UFED Physical Analyzer license.
351
Start UFED Link Analysis
Demo
Show License Details
Starts the UFED Link Analysis application.
Zip Log Files
Displays the current software or hardware (dongle) license information, and enables you to:
Activate or load a new license (software or dongle)
Display information about previous dongles that were connected to this workstation
Deactivate a software license
Get direct access via email to Cellebrite support and sales
Zips the log files and opens the folder where the zipped log files are saved.
352
Zip Log Files with System
Information
About
Zips the log files and includes detailed information about the operating system, drivers, application data, event logs etc. This information can be used to analyze report cases.
Provides information about the installed UFED Physical Analyzer version.
Index
A
Activation using a software license
Adding a binary dump
Advanced decoding
Advanced opening of a non-
52
Index
Android Unlock Password Carver plug-
B
134
Browsing t
C
Carving images
354
D
Daylight saving time
Deactivating version
Dongl
E
Extracting data from a device with a complex
Extracting data from a device with a simple
F
G
Generating a Report - Report Wi
H
Hex viewer settings
262, 267, 272, 320
I
Index
356
Installation and Activation
J
L
Locating and a
M
Managing plug-
Models settings
Moving UFED Physical Analyzer with a software
N
O
Opening an extraction in advanced mode
41, 345
Orientation to the workspace
P
Performing physical extraction from encrypted
Performing physical extraction from non-
Plug-ins
Plug-
Index
Post-
183
R
213, 217, 349
Running a specific plug6, 310, 350
358
S
Saving settings
Scanning for malware
Searchin
Searching for information in the Hex data and
Searching SMS numbers
Searching strings
Setting project settings
Setting the case inf
Starting with device selection
T
Index
U
Updating the signature datab
164
Updating the signature database from file (offline)
Using an offset to jump to a different location in
Using the Android Unlock Pattern Carver plug-
309
Using the Python
V
360
W
Welcome tab
Working in the Values tab
Working with Hex data
Working with watch lists