Briggs & Stratton 138400 Operating & Maintenance Instructions

GB
D
DK
E
F
GR
I
N
NL
P
S
SF
Operating & Maintenance Instructions
Betriebsanleitung & Wartungsvorschriften
Drifts- og vedligeholdelsesvejledning
Instrucciones de Mantenimiento & Operación
Instructions d’utilisation et de maintenance
Ïäçãßåò Ëåéôïõñãßáò & ÓõíôÞñçóçò
Istruzioni per l’uso e la manutenzione
Anvisninger for bruk og vedlikehold
Gebruiksaanwijzing
Instruções de operação e de manutenção
Instruktionsbok
Käyttö & Huolto-ohjeet
Model 50000
85400
86400
117400
118400
138400
185400
187400
235400
237400
245400
246400
247400
BRIGGSandSTRATTON.com
E Copyright Briggs & Stratton Corporation
Milwaukee, Wisconsin 53201 U.S.A.
Vanguard
Form No. MS-3824-3/07
Printed in U.S.A.
Fig. 1
6
15
5
10
11
7
3
14
8
4
2
12
1
13
9
Fig. 2
**
1
*
2
3
4
1
Fig. 3
4
7
99
6
8
OFF RUN
S TAR T
OP
ST
RUN
O
CHOKE
C
C
5
5
4
1
2
3
GB
Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed
by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton
warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer.
ENGINE COMPONENTS
GENERAL INFORMATION
Fig. 1
1 Fuel shut-off valve
2 Rope handle
3 Air cleaner
4 Engine
Model
xxxxxx
Type
xxxx xx
Code
xxxxxxxx
5 Throttle and choke controls
6 Fuel fill
In the state of California, Model 50000, 85400, 86400,
117400, 118400, 138400 engines are certified by the
California Air Resources Board to meet emissions
standards for 125 hours; Model 185400, 187400,
235400, 237400, 245400, 246400, 247400 for 250
hours. Such certification does not grant the purchaser,
owner or operator of this engine any additional
warranties with respect to the performance or operational life of this engine. This engine is warranted solely
according to the product and emissions warranties
stated elsewhere in this manual.
SAFETY SPECIFICATIONS
7 Stop switch
8 Blower housing
9 Oil drain plug
10 Muffler guard/Muffler
11 Carburetor
12 Spark plug wire
BEFORE OPERATING ENGINE
• Read entire Operator’s Manual AND the
instructions for the equipment this engine
powers.*
• Failure to follow instructions could result in
serious injury or death.
GB
WARNING
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
WARNING
Briggs & Stratton does not approve or authorize
the use of these engines on 3-wheel All Terrain
Vehicles (ATVs), motor bikes, fun/recreational
go-karts, aircraft products or vehicles intended for
use in competitive events. Use of these engines in
such applications could result in property damage,
serious injury (including paralysis), or even death.
Hazard Symbols
13 Oil fill/Dipstick − Low
14 12V electric starter, if equipped
15 Oil fill/Dipstick − High
Record your engine Model, Type and Code numbers
here for future use.
Record your date of purchase here for future use.
TECHNICAL INFORMATION
Engine Power Rating Information
The gross power rating for individual gas engine
models is labeled in accordance with SAE (Society of
Automotive Engineers) code J1940 (Small Engine
Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance
with SAE J1995 (Revision 2002-05). Torque values are
derived at 3060 RPM; horsepower values are derived
at 3600 RPM. Actual gross engine power will be lower
and is affected by, among other things, ambient
operating conditions and engine-to-engine variability.
Given both the wide array of products on which engines
are placed and the variety of environmental issues
applicable to operating the equipment, the gas engine
will not develop the rated gross power when used in a
given piece of power equipment (actual on-site" or net
power). This difference is due to a variety of factors
including, but not limited to, accessories (air cleaner,
exhaust, charging, cooling, carburetor, fuel pump,
etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-toengine variability. Due to manufacturing and capacity
limitations, Briggs & Stratton may substitute an engine
of higher rated power for this Series engine.
THE OPERATOR’S MANUAL CONTAIN SAFETY
INFORMATION TO
• Make you aware of hazards associated with
engines
• Inform you of the risk of injury associated with
those hazards, and
• Tell you how to avoid or reduce the risk of injury.
* Briggs & Stratton does not necessarily know what
equipment this engine will power. For that reason,
you should carefully read and understand the
operating instructions for the equipment on which
your engine is placed.
Fire
Explosion
Hot Surface
Toxic Fumes
Shock
Kickback
Moving Parts
International Symbols and Meanings
The safety alert symbol is used to identify safety
information about hazards that can result in personal
injury.
A signal word (DANGER, WARNING, or CAUTION) is
used with the alert symbol to indicate the likelihood and
the potential severity of injury. In addition, a hazard
symbol may be used to represent the type of hazard.
DANGER indicates a hazard which, if not
avoided, will result in death or serious
injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
CAUTION, when used without the alert
symbol, indicates a situation that could result
in damage to the engine.
1
Safety Alert
Read Owner’s
Manual
On Off
Stop
Choke
Oil
Fuel
Fuel Shutoff
WARNING
Gaseous fuels are extremely flammable and
readily form explosive air-vapor mixtures at
ambient temperatures.
GB
WARNING
Fuel and its vapors are extremely
flammable and explosive.
Fire or explosion can cause severe
burns or death.
WHEN ADDING GASOLINE
• Turn engine OFF and let engine cool at least 2
minutes before refueling engine.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. Fill tank to approximately
1-1/2 inches below top of neck to allow for fuel
expansion.
• Keep gasoline away from sparks, open flames, pilot
lights, heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently
for cracks or leaks. Replace if necessary.
WARNING
Broken bones, fractures, bruises or
sprains could result.
• When starting engine, pull cord slowly until resistance is
felt, then pull rapidly.
• Remove all external equipment/engine loads before
starting engine.
• Direct coupled equipment components such as, but not
limited to, blades, impellers, pulleys, sprockets, etc.,
must be securely attached.
•
•
•
•
OIL RECOMMENDATIONS
Engines give off carbon monoxide, an
odorless, colorless, poisonous gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
• Start and run engine outdoors in a well ventilated
area.
• Do not start or run engine in enclosed area, even if
doors or windows are open.
Engine shipped from Briggs & Stratton without oil.
Before starting engine, fill with oil. Do not over-fill.
Use a high quality detergent oil classified For Service
SF, SG, SH, SJ" or higher such as Briggs & Stratton
30W, Part Number 100005 (20 oz.) or 100028 (48 oz.).
Use no special additives with recommended oils. Do
not mix oil with gasoline.
Choose the SAE viscosity grade of oil from this chart
that matches the starting temperature anticipated
before the next oil change.
Note: Synthetic oil meeting ILSAC
GF-2, API certification mark and API service symbol (shown at left) with SJ/CF
ENERGY CONSERVING" or higher, is an
acceptable oil at all temperatures. Use of
synthetic oil does not alter required oil
change intervals.
• Do not tip engine or equipment at angle which
causes gasoline to spill.
• Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
• Transport with fuel tank EMPTY or with fuel shut-off
valve OFF, and/or fuel tank empty.
WHEN STORING FUEL OR EQUIPMENT
• Store away from furnaces, stoves, water heaters or
other appliances that have pilot light or other ignition
source because they can ignite gaseous vapors.
WARNING
Unintentional sparking can result in
fire or electric shock.
Unintentional start-up can result in
entanglement, traumatic amputation,
or laceration.
BEFORE PERFORMING ADJUSTMENTS
OR REPAIRS
WARNING
Running engines produce heat. Engine
parts, especially muffler, become extremely hot.
Severe thermal burns can occur on
contact.
Combustible debris, such as leaves,
grass, brush, etc. can catch fire.
• Disconnect battery at negative (−) terminal.
• Disconnect spark plug wire and keep it away from
spark plug.
WHEN TESTING FOR SPARK
• Use only Briggs & Stratton Spark Plug Tester.
• DO NOT check for spark with spark plug removed.
WARNING
• Allow muffler, engine cylinder and fins to cool
before touching.
• Engine should be kept clean to reduce the risk of
overheating and ignition of accumulated debris.
Clean engine when it is cold, especially in the
muffler and manifold areas.
• Install and maintain in working order a spark
arrester before using equipment on forest-covered, grass-covered, brush-covered unimproved
land. (The state of California Public Resources
Code Section 4442 requires a spark arrester in
working order.) Other states may have similar
laws. Federal laws apply on federal land.
Operate equipment with guards in place.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
DO NOT wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
Fig. 2
WHEN STARTING ENGINE
WHEN OPERATING EQUIPMENT WITH
GASOLINE ENGINE
Rotating parts can contact or entangle
hands, feet, hair, clothing, or accessories.
Traumatic amputation or severe laceration can result.
Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine
faster than you can let go.
WARNING
• Make sure spark plug, muffler, fuel cap and air
cleaner are in place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting
engine.
• If engine floods, set choke to OPEN/RUN position,
place throttle in FAST and crank until engine starts.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
• If there is natural or LP gas leakage in area, do not start
engine.
• Do not use pressurized starting fluids because vapors
are flammable.
• Servicing of products fueled by Natural Gas (NG) or
Liquid Petroleum Gas (LPG) may require licensing or
permits issued by state, provincial, and/or local
governments.
2
*
Air cooled engines run hotter than automotive
engines. The use of non-synthetic multi-viscosity
oils (5W-30, 10W-30, etc.) in temperatures
above 40° F (4° C) will result in higher than
normal oil consumption. When using a multi-viscosity oil, check oil level more frequently.
** SAE 30 oil, if used below 40° F (4° C), will result
in hard starting and possible engine bore
damage due to inadequate lubrication.
Oil Capacity
(Approximate amount when changing oil and filter.)
Model
Liters
Ounces
050000
.4
13.5
085400, 086400
.6
20
117400
.7
24
118400
.7
24
138400
.9
32
184400, 185400, 187400
.9
32
235400, 237400, 245400,
246400, 247400
.9
32
Place engine level and clean around oil fill .
Remove dipstick and wipe with clean cloth. Insert
dipstick in oil fill − tighten down if high oil fill , but do
not tighten down if low oil fill − remove dipstick to
check oil level. Oil should be at FULL mark .
If oil is required, add slowly. Do not over-fill. Tighten
dipstick firmly before starting engine.
GB
FUEL RECOMMENDATIONS
THE GASOLINE ENGINE IS CERTIFIED TO OPERATE ON GASOLINE. Exhaust Emission Control System: EM (Engine Modifications).
Use clean, fresh, lead-free gasoline with a minimum of
85 octane. Leaded gasoline may be used if it is
commercially available and if unleaded is unavailable.
Purchase fuel in quantity that can be used within 30
days. See Storage.
In U.S.A. leaded gasoline may not be used. Some
fuels, called oxygenated or reformulated gasolines, are
gasolines blended with alcohols or ethers. Excessive
amounts of these blends can damage the fuel system
or cause performance problems. If any undesirable
operating symptoms occur, use gasoline with a lower
percentage of alcohol or ether.
Do not use gasoline which contains Methanol. Do not
mix oil with gasoline.
Check fuel level
Rewind starter
Air cleaner service
WARNING
• Grasp rope handle and pull slowly until
resistance is felt. Then pull cord rapidly to
overcome compression, prevent kickback
and start engine.
Repeat if necessary with choke in RUN position and
throttle in FAST. When engine starts, operate in FAST
position.
Electric starter, if equipped
Turn key to START position. Repeat if necessary
with throttle control in FAST position. When engine
starts, operate in FAST position.
Note: If equipment manufacturer has supplied battery,
charge it before trying to start engine, as equipment
manufacturer recommends.
Note: Use short starting cycles (15 secs. per min.) to
prolong starter life. Extended cranking can damage
starter motor.
WARNING
• Before refueling, allow engine to cool 2
minutes.
Clean around fuel fill before removing cap to refuel. Fill
tank to approximately 1-1/2 inches below top of neck to
allow for fuel expansion. Be careful not to overfill.
STARTING
WARNING
ALWAYS KEEP HANDS AND FEET
CLEAR OF EQUIPMENT MOVING
PARTS.
STOPPING
Fig. 3
Fig. 6
Replace pre-cleaner , and/or cartridge if very dirty
or damaged.
1. Loosen screws. Remove cover and air cleaner
assembly from base.
2. Remove cartridge retainer , (if equipped) and
pre-cleaner.
To service pre-cleaner, wash in liquid detergent and
water. Squeeze dry in a clean cloth. Saturate in engine
oil. Squeeze in clean, absorbent cloth to remove ALL
EXCESS oil.
To service cartridge, clean by tapping gently on a flat
surface. Do not use petroleum solvents, e.g., kerosene, which will cause cartridge to deteriorate. Do not
use pressurized air, which can damage cartridge. Do
not oil cartridge.
3. Reinstall pre-cleaner on retainer, if equipped.
4. Install pre-cleaner in cover with mesh side toward
cartridge. Install cartridge in cover or on base.
5. Seat cover and air cleaner assembly squarely
onto base (tabs into slots , if equipped).
6. Tighten cover screws securely.
Check valve clearance:
intake is .05 mm and exhaust .10 mm.
Do not move choke control to CHOKE position to stop
engine. Backfire or engine damage may occur. Move
throttle control to IDLE or SLOW position, if
equipped. Then turn key to OFF or move stop
control to OFF position. Close fuel shut-off valve .
Note: Always remove key from switch when equipment
is not in use or left unattended.
Note: When engine is transported, close fuel shut-off
valve to prevent leakage.
Spark plug service
Fig. 5
WARNING
• DO NOT check for spark with spark
plug removed. Use only Briggs &
Stratton Spark Tester , to check for
spark.
• DO NOT crank engine with spark
plug removed. If engine is flooded,
place throttle in FAST and crank until
engine starts.
MAINTENANCE
WARNING
Fig. 4
• Do not use pressurized starting fluid.
Vapors are flammable.
Check oil level.
Open fuel shut-off valve, if equipped.
OIL GARD
If engine is equipped with OIL GARD, and if engine runs
low on oil and cannot be started or has stopped and
cannot be restarted, add oil. Fill to FULL mark on
dipstick. Do not over-fill.
CAUTION: OIL GARD will shut down a running
engine. Engine damage may occur if oil level is not
properly maintained and will void warranty coverage.
STARTING
Fig. 3
1.
2.
3.
4.
Move choke control to CHOKE position.
Move throttle control to FAST position.
Turn on fuel shut-off valve .
Move stop control to ON position, if equipped.
WARNING
• To prevent accidental starting, remove spark
plug wire and ground it before servicing,and disconnect battery at negative
terminal, if equipped.
See Maintenance Schedule. Follow the hourly or
calendar intervals, whichever occur first. More frequent
service is required when operating in adverse conditions.
Oil service
Fig. 2
Spark plug gap should be .76 mm or 0.030 in.
Replace spark plug every 100 hours or every season,
whichever occurs first. Spark tester and spark plug
wrench are available from any Authorized Briggs &
Stratton Service Dealer.
Note: In some areas, local law requires using a resistor
spark plug to suppress ignition signals. If this engine
was originally equipped with resistor spark plug, use
same type of spark plug for replacement.
Keep engine clean
Check oil level regularly.
Be sure correct oil level is maintained. Check every 8
hours or daily, before starting engine. See oil filling
procedure under Oil Recommendations.
Change oil.
Change oil after first 5 hours of operation. Change oil
while engine is warm. Refill with new oil of recommended SAE viscosity grade.
3
Fig. 7
Periodically remove chaff and debris build-up from
engine. Do not spray engine with water to clean
because water could contaminate fuel. Clean with a
brush or compressed air.
To assure smooth operation, keep governor linkage,
springs and controls free of debris .
GB
WARNING
Partial List of Genuine
Briggs & Stratton Parts
STORAGE
• Accumulation of debris around muf-
fler could cause a fire. Inspect and
clean before every use.
If muffler is equipped with spark arrester screen ,
remove spark arrester screen for cleaning and inspection every 50 hours or every season. Replace if
damaged.
Clean cooling system. Chaff or debris may clog engine’s
air cooling system, especially after prolonged operation.
Internal cooling fins and surfaces may require cleaning
to prevent overheating and engine damage. Remove
blower housing and clean as shown .
Clean fuel filter
Fig. 8
CAUTION: Part numbers listed may be model specific, use correct part to prevent damage to your engine.
Model
Part
Part
No.
ALL
Oil
(20 oz., 0.59 l)
100005
ALL
Oil
(48 oz., 1.42 l)
100028
ALL
Oil Pump
(uses standard
electric drill)
5056
ALL
Fuel Stabilizer
5058
050000
Air Cleaner
Cartridge
711351
050000
Air Cleaner
Pre-cleaner
11352
085400
Air Cleaner
Cartridge
710265
085400
Air Cleaner
Pre-cleaner
710267
050000, 086400,
117400, 118400,
138400, 185400*,
187400*, 237400*,
245400*, 246400
Square
Air Cleaner
Cartridge
491588
246400, 247400
Square
Air Cleaner
711785
050000, 086400,
117400, 118400,
138400, 185400*,
187400*, 237400*,
245400*, 246400
Square
Air Cleaner
Pre-cleaner
491435
185400, 235400,
245400
Air Cleaner
Cartridge
710266
185400,
235400, 237400,
245400
Air Cleaner
Pre-cleaner
710268
ALL
(Except 050000,
086400, 118400)
Resistor Spark
Plug
491055
050000,
086400, 118400
Resistor Spark
Plug
711252
ALL OHV engines
(Except 050000,
086400, 118400)
Long Life
Platinum Spark
Plug
491055
ALL
Spark Tester
19368
ALL
Spark Plug
Wrench
19374
WARNING
• Drain fuel tank or close fuel shut-off
valve before cleaning filter
Gasoline Engines: Clean fuel filter screen .
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occur first. More frequent service is required when
operating in adverse conditions noted below.
First 5 Hours
D Change oil
Every 8 hours or daily
D Check oil level
D Clean around muffler, springs and linkages
Every 25 hours or every season
D Service air cleaner pre-cleaner*
Every 50 hours or every season
D Change oil if operating under heavy load or
high ambient temperature
D Clean and inspect spark arrester, if equipped
D Clean fuel filter
Every 100 hours or every season
D Change oil
D Service air cleaner cartridge*
D Replace spark plug
D Clean cooling system*
Every season
D Check valve clearance
*
* If equipped.
Clean more often under dusty conditions, or
when airborne debris or chaff is present.
4
Gasoline engines stored over 30 days need to be
protected or drained of fuel to prevent gum from
forming in fuel system or on essential carburetor parts.
For gasoline engine protection, we recommend use of
Briggs & Stratton Fuel Stabilizer available from an
Authorized Briggs & Stratton Service Dealer. Mix
stabilizer with fuel in fuel tank or storage container. Run
engine for a short time to circulate stabilizer through
carburetor. Engine and fuel can be stored up to 24
months.
Note: If stabilizer is not used or if engine is operating on
gasoline containing alcohol, e.g. gasohol, remove all fuel
from tank and run engine until it stops from lack of fuel.
Storage Procedures for Gas/LPG/NG engines.
Fig. 2
Fig. 7
1. Change oil. See Oil service.
2. Remove spark plug and pour about 15 ml (1/2
oz.) of engine oil into cylinder. Replace spark plug
and crank slowly to distribute oil.
3. Clean chaff and debris from cylinder and cylinder
head fins, under finger guard and behind muffler.
4. Store in a clean and dry area, but NOT near a
stove, furnace or water heater which uses a pilot
light or any device that can create a spark.
SERVICE
See an Authorized Briggs & Stratton Service Dealer.
Each one carries a stock of Genuine Briggs & Stratton
Parts and is equipped with special service tools.
Trained mechanics assure expert repair service on all
Briggs & Stratton engines. Only dealers advertising as
Authorized Briggs & Stratton" are required to meet
Briggs & Stratton standards.
When you purchase equipment powered by a Briggs & Stratton engine, you
are assured of highly skilled, reliable
service at more than 30,000 Authorized
Service Dealers worldwide, including
more than 6,000 Master Service Technicians. Look for these signs wherever
Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs &
Stratton Service Dealer in our dealer locator map on
our web site www.briggsandstratton.com or in the
Yellow Pages™" directory under Engines,
Gasoline" or Gasoline Engines," or Lawn
™ Mowers" or similar category.
Note: Walking fingers logo and Yellow Pages" are
registered trademarks in various jurisdictions.
An illustrated shop manual includes Theories of
Operation," common specifications and detailed
information covering adjustment, tune-up and repair of
Briggs & Stratton single cylinder, OHV 4 cycle engines.
Order P/N 272147 from an Authorized Briggs &
Stratton Service Dealer.
Insist on Genuine Briggs & Stratton replacement p arts
with our logo on the box and/or part. Non-original parts
may not perform as well and may void your warranty.
GB
Briggs & Stratton Corporation (B&S),
the California Air Resources Board (CARB)
and the United States
Environmental Protection Agency (U.S. EPA)
Emissions Control System Warranty Statement
(Owner’s Defect Warranty Rights and Obligations)
California, United States and Canada Emissions
Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. EPA
and B&S are pleased to explain the Emissions Control
System Warranty on your small off-road engine (SORE).
In California, new small off-road engines model year 2006
and later must be designed, built and equipped to meet
the State’s stringent anti-smog standards. Elsewhere in
the United States, new non-road, spark-ignition engines
certified for model year 1997 and later must meet similar
standards set forth by the U.S. EPA. B&S must warrant the
emissions control system on your engine for the periods of
time listed below, provided there has been no abuse, neglect or improper maintenance of your small off-road engine.
Your emissions control system includes parts such as the
carburetor, air cleaner, ignition system, fuel line, muffler
and catalytic converter. Also included may be connectors
and other emissions related assemblies.
Where a warrantable condition exists, B&S will repair your
small off-road engine at no cost to you including diagnosis, parts and labor.
Briggs & Stratton Emissions Control
Defects Warranty Coverage
Small off-road engines are warranted relative to emissions control parts defects for a period of two years, subject to provisions set forth below. If any covered part on
your engine is defective, the part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities
As the small off-road engine owner, you are responsible
for the performance of the required maintenance listed in
your Operating and Maintenance Instructions. B&S recommends that you retain all your receipts covering maintenance on your small off-road engine, but B&S cannot
deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should however
be aware that B&S may deny you warranty coverage if
your small off-road engine or a part has failed due to
abuse, neglect, improper maintenance or unapproved
modifications.
You are responsible for presenting your small off-road engine to an Authorized B&S Service Dealer as soon as a
problem exists. The undisputed warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights
and responsibilities, you should contact a B&S Service
Representative at 1-414-259-5262.
The emissions warranty is a defects warranty. Defects are
judged on normal engine performance. The warranty is
not related to an in-use emissions test.
Briggs & Stratton Emissions Control
Defects Warranty Provisions
The following are specific provisions relative to your Emissions Control Defects Warranty Coverage. It is in addition
to the B&S engine warranty for non-regulated engines
found in the Operating and Maintenance Instructions.
1. Warranted Parts
Coverage under this warranty extends only to the parts
listed below (the emissions control systems parts) to the
extent these parts were present on the engine purchased.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor and internal parts
• Fuel pump
• Fuel line, fuel line fittings, clamps
• Fuel tank, cap and tether
• Carbon canister
b. Air Induction System
• Air cleaner
• Intake manifold
• Purge and vent line
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive
valves and switches
• Connectors and assemblies
2. Length of Coverage
B&S warrants to the initial owner and each subsequent
purchaser that the Warranted Parts shall be free from defects in materials and workmanship which caused the failure of the Warranted Parts for a period of two years from
the date the engine is delivered to a retail purchaser.
3. No Charge
Repair or replacement of any Warranted Part will be performed at no charge to the owner, including diagnostic labor which leads to the determination that a Warranted
Part is defective, if the diagnostic work is performed at an
Authorized B&S Service Dealer. For emissions warranty
service contact your nearest Authorized B&S Service
Dealer as listed in the Yellow Pages" under Engines,
Gasoline," Gasoline Engines," Lawn Mowers," or similar
category.
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the B&S Engine Warranty Policy. Warranty coverage shall be excluded for failures of Warranted Parts
which are not original B&S parts or because of abuse, neglect or improper maintenance as set forth in the B&S Engine Warranty Policy. B&S is not liable to cover failures of
Warranted Parts caused by the use of add-on, non-original, or modified parts.
5. Maintenance
Any Warranted Part which is not scheduled for replacement as required maintenance or which is scheduled only
for regular inspection to the effect of repair or replace as
necessary" shall be warranted as to defects for the warranty period. Any Warranted Part which is scheduled for
replacement as required maintenance shall be warranted
as to defects only for the period of time up to the first
scheduled replacement for that part. Any replacement
part that is equivalent in performance and durability may
be used in the performance of any maintenance or repairs. The owner is responsible for the performance of all
required maintenance, as defined in the B&S Operating
and Maintenance Instructions.
6. Consequential Coverage
Coverage hereunder shall extend to the failure of any engine components caused by the failure of any Warranted
Part still under warranty.
5
Look For Relevant Emissions
Durability Period and
Air Index Information On
Your Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emissions Standards must
display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the consumer on our emissions labels. The engine emissions label will indicate certification
information.
The Emissions Durability Period describes the number
of hours of actual running time for which the engine is certified to be emissions compliant, assuming proper maintenance in accordance with the Operating & Maintenance
Instructions. The following categories are used:
Moderate:
Engine is certified to be emissions compliant for 125 hours
of actual engine running time.
Intermediate:
Engine is certified to be emissions compliant for 250 hours
of actual engine running time.
Extended:
Engine is certified to be emissions compliant for 500 hours
of actual engine running time. For example, a typical walkbehind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions Durability Period of an engine with
an intermediate rating would equate to 10 to 12 years.
Certain Briggs & Stratton engines will be certified to meet
the United States Environmental Protection Agency
(USEPA) Phase 2 emissions standards. For Phase 2 certified engines, the Emissions Compliance Period referred
to on the Emissions Compliance label indicates the number of operating hours for which the engine has been
shown to meet Federal emissions requirements.
For engines less than 225 cc displacement.
Category C = 125 hours
Category B = 250 hours
Category A = 500 hours
For engines of 225 cc or more displacement.
Category C = 250 hours
Category B = 500 hours
Category A = 1000 hours
GB
BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY
Effective 12/06
LIMITED WARRANTY
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is
subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pagest.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS
PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state and country to country.
WARRANTY TERMS**
Brand / Product Type
Vanguardt
Extended Life Seriest, I/CR, Intek I/CR, Intek Prot
Kerosene fuel operated engines
All other Briggs & Stratton engines
Consumer Use
2 years
2 years
1 year
2 years
Commercial Use
2 years
1 year
90 days
90 days
**Engines used on Home Standby Generator applications are warranted under consumer use only. This warranty does not apply to engines on
equipment used for prime power in place of a utility. Engines used in competitive racing or on commercial or rental tracks are not warranted.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”
means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an
engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF
YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE
PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR ENGINE WARRANTY
Briggs & Stratton welcomes warranty repair and
apologizes to you for being inconvenienced. Any
Authorized Service Dealer may perform warranty repairs.
Most warranty repairs are handled routinely, but
sometimes requests for warranty service may not be
appropriate. For example, warranty would not apply if
engine damage occurred because of misuse, lack of
routine maintenance, shipping, handling, warehousing or
improper installation. Similarly, warranty is void if the
serial number of the engine has been removed or the
engine has been altered or modified.
If a customer differs with the decision of the Service
Dealer, an investigation will be made to determine
whether the warranty applies. Ask the Service Dealer to
submit all supporting facts to his Distributor or the Factory
for review. If the Distributor or the Factory decides that the
claim is justified, the customer will be fully reimbursed for
those items that are defective. To avoid misunderstanding
which might occur between the customer and the Dealer,
listed below are some of the causes of engine failure that
the warranty does not cover.
Normal wear:
Engines, like all mechanical devices, need periodic parts
service and replacement to perform well. Warranty will not
cover repair when normal use has exhausted the life of a
part or an engine.
Improper maintenance:
The life of an engine depends upon the conditions under
which it operates, and the care it receives. Some
applications, such as tillers, pumps and rotary mowers,
are very often used in dusty or dirty conditions, which can
cause what appears to be premature wear. Such wear,
when caused by dirt, dust, spark plug cleaning grit, or
other abrasive material that has entered the engine
because of improper maintenance, is not covered by
warranty.
This warranty covers engine related defective
material and/or workmanship only, and not
replacement or refund of the equipment to which the
engine may be mounted. Nor does the warranty
extend to repairs required because of:
1. PROBLEMS CAUSED BY PARTS THAT ARE NOT
ORIGINAL BRIGGS & STRATTON PARTS.
2. Equipment controls or installations that prevent
starting, cause unsatisfactory engine performance,
or shorten engine life. (Contact equipment
manufacturer.)
3. Leaking carburetors, clogged fuel pipes, sticking
valves, or other damage, caused by using
contaminated or stale fuel.
4. Parts which are scored or broken because an engine
was operated with insufficient or contaminated
lubricating oil, or an incorrect grade of lubricating oil
(Check and refill when necessary, and change at
recommended intervals.) OIL GARD may not shut
down running engine. Engine damage may occur if
oil level is not properly maintained.
5. Repair or adjustment of associated parts or
assemblies such as clutches, transmissions, remote
controls, etc., which are not manufactured by Briggs
& Stratton.
6. Damage or wear to parts caused by dirt, which
entered the engine because of improper air cleaner
maintenance, re-assembly, or use of a non-original
Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending)
6,691,683
6,520,141
6,325,036
6,145,487
6,012,420
5,803,035
6,647,942
6,495,267
6,311,663
6,142,257
5,992,367
5,765,713
6,622,683
6,494,175
6,284,123
6,135,426
5,904,124
5,732,555
6,615,787
6,472,790
6,263,852
6,116,212
5,894,715
5,645,025
6,617,725
6,460,502
6,260,529
6,105,548
5,887,678
5,642,701
6,603,227
6,456,515
6,242,828
6,347,614
5,852,951
5,628,352
6,595,897
6,382,166
6,239,709
6,082,323
5,843,345
5,619,845
6,595,176
6,369,532
6,237,555
6,077,063
5,823,153
5,606,948
6,584,964
6,356,003
6,230,678
6,064,027
5,819,513
5,606,851
6,557,833
6,349,688
6,213,083
6,040,767
5,813,384
5,605,130
6,542,074
6,347,614
6,202,616
6,014,808
5,809,958
5,497,679
6
5,548,955
5,546,901
5,445,014
5,503,125
5,501,203
5,497,679
5,320,795
5,301,643
5,271,363
5,269,713
5,265,700
air cleaner element or cartridge. At recommended
intervals, clean and/or replace the filter as stated in
the Operator’s Manual.
7. Parts damaged by over-speeding, or overheating
caused by grass, debris, or dirt, which plugs or clogs
the cooling fins, or flywheel area, or damage caused
by operating the engine in a confined area without
sufficient ventilation. Clean engine of debris at
recommended intervals as stated in the Operator’s
Manual.
8. Engine or equipment parts broken by excessive
vibration caused by a loose engine mounting, loose
cutter blades, unbalanced blades or loose or
unbalanced impellers, improper attachment of
equipment to engine crankshaft, over-speeding or
other abuse in operation.
9. A bent or broken crankshaft, caused by striking a
solid object with the cutter blade of a rotary lawn
mower, or excessive v-belt tightness.
10. Routine tune-up or adjustment of the engine.
11. Engine or engine component failure, i.e.,
combustion chamber, valves, valve seats, valve
guides, or burned starter motor windings, caused by
the use of alternate fuels such as, liquified
petroleum, natural gas, altered gasolines, etc.
Warranty service is available only through authorized
service dealers by Briggs & Stratton Corporation.
Locate your nearest Authorized Service Dealer in our
dealer locator map on BRIGGSandSTRATTON.com or
by calling 1-800-233-3723, or as listed in the ’Yellow
Pagest’.
5,243,878
5,235,943
5,234,038
5,228,487
5,197,426
5,197,425
5,197,422
5,191,864
5,188,069
5,186,142
5,150,674
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,977,877
4,971,219
4,895,119
4,875,448
4,819,593
4,720,638
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
D
D
D
D
D
D
D
D
D
D
D
476,629
457,891
368,187
375,963
309,457
372,871
361,771
356,951
309,457
308,872
308,871
Fig. 4
Fig. 5
2
3
1
Fig. 6
3
6
3
2
4
2
5
Fig. 7
3
2
Fig. 8
1
4
">