Accessories
Q26
Quick Install
Q26 Hemispheric
Outdoor Wall Mount
On-Wall Set 10°
On-Wall Set
•
•
•
•
•
•
•
Vandalism Kit
Cavity Wall Installation Set
Hemispheric 6MP Dome Camera with
Day or Night Image Sensor for Ceiling,
Wall and Pole Mounting
MOBOTIX 6MP camera for flexible use in indoor and
outdoor applications, available as complete Q26
Hemispheric (Day or Night) with 180-degree lens. Can
be extended flexibly using various sets for outdoor
applications, on-wall or flush-mount installations. Use
the Vandalism Kit for surveillance at extremely critical
locations.
Mx6 system platform with H.264 support
Includes MxAnalytics video analysis tools out-of-the-box
Recording on internal MicroSD card (SDXC, SDHC installed)
Audio integrated (microphone and speaker)
Sensor for temperature and shock detector(*) integrated
Weatherproof and robust camera housing (IP66, IK06)
Simply mounted to poles using Pole Mount (accessory)
More information:
www.mobotix.com > Products > Outdoor Cameras > Hemispheric Q26
Mx-Q26
32.833-002_EN_09/2017
*: with firmware version 5.0.1 and higher
Standard Delivery Q26
1.1
1.2
1.16
1.3
1.15
1.14
1.4
1.13
1.12
1.11
1.5
1.6
1.7
1.10
1.8
Item
Count
1.1
1
Part Name
Camera housing
1.2
1
Lens (installed)
1.3
1
Lens wrench
1.4
1
MicroSD card (SDXC, SDHC pre-installed)
1.5
1
Ethernet patch cable CAT5 0.5 m/1.64 ft
1.6
1
Allen wrench 3 mm
1.7
1
Allen wrench 2 mm
1.8
1
Torx wrench TX20
1.9
1
Outer shell
1.10
4
Mounting ring
1.11
4
Stainless steel washers 5.3 mm dia.
1.12
4
Dowels 8 mm
1.13
4
Stainless steel Torx screws 4.5x60 mm
1.14
4
Stainless steel washers 4.3 mm dia.
1.15
1
Stainless steel Allen screws M4x16 mm
1.16
2
Cable lock with bayonet catch (Ethernet patch cable, MiniUSB)
1.9
Connections and Initial Operation of the Q26
You can find detailed information on the installation and connections of the Q26 in the Q25 Camera Manual (PDF, available on www.mobotix.com >
Support > Manuals).
Please note that the boot options of this camera have changed compared to its predecessor (see «Boot Options of the Q26» on page 1) and the camera only has one key ("R"). Regarding the rest of the initial operation of the Q26, please see the Q25 Camera Manual in Chapter 3, «Initial Operation».
Mounting
ring
Outer shell
Camera
Network connection
Lens
LEDs
USB
Slot for MicroSD card
(inside)
"R" key
Mounting Options of the Q26
Prepare the Camera
Remove the outer shell of the Q26 (if installed). Then, remove the bayonet lock and the blue plug from the network connection. Insert the patch
cable (item 1.5) into the network connection and secure it again with the
bayonet lock.
100 mm
Installation on Walls or Ceilings Without Accessories
Dia. 5.5 mm
100 mm
After drilling the holes for fixtures (see «Drilling Templates»), attach the
mounting ring of the Q26 at the designated position using dowels and screws.
Next, connect the cabling, point the camera into the viewing direction and
adjust the focus of the lens (see «Adjusting the Lens Focus of the Q26» on
page 2). Finally, install the camera's outer shell.
1.4
14
mm
Installation With On-Wall Set/On-Wall Set 10° (Accessory)
After drilling the holes for fixtures (see «Drilling Templates»), attach the
On-Wall Set at the designated position using dowels and screws, then lead
the cabling into the On-Wall Set. Next, remove the mounting ring of the
Q26, connect the cabling and install the camera on the On-Wall Set. Finally,
install the camera's outer shell.
Installation With Cavity Wall Installation Set (Accessory)
After cutting out the hole (see «Drilling Templates»), remove the mounting
ring of the Q26 and install the camera in the Cavity Wall Installation Set.
Next, connect the cabling and install the camera together with the
Cavity Wall Installation Set into the cut-out and fasten it using the winged
cams. Finally, press the decoration ring onto the camera and lock it in place
using the toothed wrenches.
Installation With Outdoor Wall Mount (Accessory)
Remove the cover plate of the Outdoor Wall Mount. After drilling the holes
for fixtures (see «Drilling Templates»), attach the Outdoor Wall Mount at
the designated position using dowels and screws, then lead the cabling
into the mount. Next, remove the mounting ring of the Q26, connect the
cabling and click the camera into the clamps of the cover plate of the
Outdoor Wall Mount. Then attach the cover plate with the camera to the
Outdoor Wall Mount. Finally, install the camera's outer shell.
Installation With Pole Mount and Outdoor Wall Mount (Accessory)
Lead the cabling from the rear through the Pole Mount and attach to a pole
(using steel straps). Then attach the Outdoor Wall Mount to the Pole Mount.
The remaining installation of the Q26 follows the steps under «Installation
With Outdoor Wall Mount (Accessory)» above.
Installation of the Vandalism Kit (Accessory)
Remove the lens using the lens wrench and remove the lens gasket. Screw
the lens back into the lens mount and correct the lens' focus (see «Adjusting
the Lens Focus of the Q26» on page 2). Screw in the reinforced dome
and set the four spacers onto the mounting ring of the camera. Place the
stainless steel outer shell onto the camera and tighten it using the four
security screws.
4x
Inserting/Exchanging the SD Card
All camera models can use the integrated MicroSD card (SDHC) to record video data. In order to exchange the MicroSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website www.mobotix.com > Support > MxMedia Library >
Planning in the document MicroSD Card Whitelist for MOBOTIX Cameras.
When replacing the SD card, make sure that recording has been deactivated in the browser (Admin Menu > Storage > Storage on External File Server /
Flash Device; activate recording again in the same dialog).
1. Remove the SD card
2. Insert the SD card
Remove the back of the camera housing. If a
MicroSD card has been installed, gently press
with your finger as indicated by the arrow until
you hear a click. Then release the SD card. The
card is protruding slightly and can be easily
removed.
Insert the MicroSD card and gently press with
your finger as indicated by the arrow until you
hear another click. Make sure that the SD card
is fully inserted. Install the back of the camera
housing.
!
Click
!
Click
Boot Options of the Q26
By default, the camera starts as DHCP client and automatically tries to get
an IP address from a DHCP server. To start the camera in a mode different
from the default mode, you can activate the boot menu of the camera.
1. Preparing the Camera
LED
flashes
Boot
Option
1x
Not used
2x
Factory
Defaults
3x
Automatic
IP Address
4x
Recovery
System
• Disconnect the camera's power supply.
• Make sure that you have suitable item such as a paper clip at hand,
but never use sharp or pointed objects!
• Reconnect the power supply of the camera.
2. Activating the Boot Menu
The red LED lights up 5 to 10 seconds after establishing the power supply and will stay on for 10 seconds.
Briefly press the key by inserting the paper clip into
the hole indicated by the red circle in the figure. The
camera enters the boot menu, ready for selecting one
of the boot options.
The LED now flashes once and repeats the flash signal after pausing for
one second (the number of flashes indicates the current boot option). To
go to the next boot option, briefly press the key again (< 1 sec). After the
last boot option, the camera returns to the first option (LED flashes once).
Meaning
Not available on this camera model.
Starts the camera with factory defaults
(factory default IP address, users and
passwords will not be reset).
Starts the camera as DHCP client and
tries to obtain an IP address from a
DHCP server. If a DHCP server cannot
be found or no IP address can be
obtained, the camera starts with its
factory default address.
Starts the camera with the recovery
system, e.g., in order to recover from a
failed update of the camera software.
Audio
Confirmation*
_
Boing
Boing Boing
Alarm Sound
*Only on cameras with audio option and installed speaker.
3. Selecting a Boot Option
Press the paper clip longer (> 2 sec) into the hole. The camera confirms the
selection by flashing rapidly three times. You can now remove the paper
clip. After 20 sec, the camera will confirm the selection by playing a sound
according to the table above.
If nothing is selected, the camera will resume its normal boot process
after a certain time.
Adjusting the Lens Focus of the Q26
If installed, remove the dome (using the wide side of the lens wrench,
item 1.3) before proceeding.
Using the lens wrench (item 1.3), carefully turn
the lens in clockwise or counter-clockwise
direction until the red area of the focusing
aid is as small as possible.
Check the live image from the camera in the browser (enter the camera's
IP address in the browser address bar). Activate the focusing aid in the
browser (Focusing Aid quick control, Activated value).
Once the focus is adjusted properly, deactivate
the focusing aid again (Focusing Aid quick
control, Disabled value).
Reinstall the dome, if required.
Important Notes
Safety Warnings
Notes on Installing:
• This product must not be used in locations exposed to
the dangers of explosion.
• Make sure that you install this product as outlined in
Chapter 2, «Installation» of the corresponding manual.
A faulty installation can damage the camera!
• When installing this product, make sure that you are only
using genuine MOBOTIX parts and MOBOTIX connection
cables.
• Only install this product on suitable, solid materials that
provide for a sturdy installation of the fixing elements
used.
Network security: MOBOTIX products include all of the necessary configuration options for operation in Ethernet networks in compliance with data protection laws. The operator
is responsible for the data protection concept across the entire
system. The basic settings required to prevent misuse can be
configured in the software and are password-protected. This
prevents unauthorized parties from accessing these settings.
Legal Notes
Legal aspects of video and sound recording: You must comply
with all data protection regulations for video and sound monitoring when using MOBOTIX products. Depending on national
laws and the installation location of the Q26, the recording of
video and sound data may be subject to special documentation
or it may be prohibited. All users of MOBOTIX products are
therefore required to familiarize themselves with all applicable
regulations and to comply with these laws. MOBOTIX AG is not
liable for any illegal use of its products.
Electrical installation: Electrical systems and equipment may
only be installed, modified and maintained by a qualified
electrician or under the direction and supervision of a qualified
electrician in accordance with the applicable electrical guidelines. Make sure to properly set up all electrical connections.
Electrical surges: MOBOTIX cameras are protected against
the effects of small electrical surges by numerous measures.
These measures, however, cannot prevent the camera from
being damaged when stronger electrical surges occur. Special
care should be taken when installing the camera outside of
buildings to ensure proper protection against lightning, since
this also protects the building and the whole network infrastructure.
§
Disposal
Electrical and electronic products contain many valuable
materials. For this reason, we recommend that you dispose
of MOBOTIX products at the end of their service life in accordance with all legal requirements and regulations (or deposit
these products at a municipal collection center). MOBOTIX
products must not be disposed of in household waste! If the
product contains a battery, please dispose of the battery separately (the corresponding product manuals contain specific
directions if the product contains a battery).
Never touch the lens: Due to the high performance of the
Q26, the area of the image sensor can get quite hot, especially
when the ambient temperature is also high. This does not
affect the proper functioning of the camera in any way. For
this reason, the product must not be installed within the reach
of persons without dome.
Disclaimer
MOBOTIX AG does not assume any responsibility for damages,
which are the result of improper use or failure to comply to the
manuals or the applicable rules and regulations. Our General
Terms and Conditions apply. You can download the current
version of the General Terms and Conditions from our website at www.mobotix.com by clicking on the COS link at the
bottom of every page.
Power off before opening the camera: Make sure the power
supply to the camera is disconnected before opening the camera
housing (e.g., when exchanging the SD card or when opening
the body to attach wires).
§
Technical Specifications Q26
Model Variants
Mx-Q26A-6D016 (daylight image sensor, color)
Mx-Q26A-6N016 (night image sensor, Black&White)
Lens Option
B016 (focal length 1.6 mm, f/2.0, image angle 180°x180°)
Sensitivity
• Color sensor (daylight): 0,1 lx @ 1/60s; 0,005 lx @ 1s
• Black&White sensor (night): 0,02 lx @ 1/60s; 0,001 lx @ 1s
Image Sensor
1/1.8“ CMOS, 6MP (3072x2048), Progressive Scan
Max. Image Size
6MP (3072x2048)
Image Formats
Max. Frame Rate
Video Codec
DVR
Freely configurable 4:3, 8:3, 16:9 or custom formats (image
cropping), e.g., 2592x1944 (5MP), 2048x1536 (QXGA), 1920x1080
(Full-HD), 1280x960 (MEGA)
• MxPEG: 42@HD(1280x720), 34@Full-HD, 24@QXGA, 15@5Mp,
12@6MP
• M-JPEG: 26@HD(1280x720), 13@Full-HD, 9@QXGA, 5@5Mp,
4@6MP
• H.264: 25@Full-HD, 20@QXGA
• MxPEG, M-JPEG, JPEG (max. output size 6MP)
• H.264 (max. output size QXGA, bandwidth limitation applicable)
• In the camera on MicroSD card (SDXC, SDHC pre-installed)
• External, on USB device
• External, on NAS
• Separate live image and full image recording – MxFFS with
archiving function
• Pre- and post-alarm images
• Automatic DVR monitoring with error notification
Software
MxManagementCenter
Image Processing
MxLEO, backlight compensation, automatic white balance, distortion correction
PTZ
Digital pan/tilt/zoom, continuous up to 8X
Alarm/Events
Temperature sensor, shock detector (with firmware version
5.0.1 and higher), microphone, additional sensors/IOs via
MxMessageSystem, notification via e-mail, FTP, IP telephony (VoIP,
SIP), visual/sound alarms, pre- and post-alarm images
Intelligent Video
Analysis
MxActivitySensor, video motion analysis, MxAnalytics
Audio
• Microphone/speaker, both 16bit/16kHz (HD wideband audio)
• Lip-synchronous audio, audio recording
• VoIP/SIP telephony, intercom, remote controlling using key codes
Interfaces
Ethernet 100BaseT (MxRJ45), MiniUSB (MxMiniUSB)
User/group management, HTTPS/SSL, IP address filter, IEEE 802.1x,
intrusion detection, digital image signature, MxFFS
EN55022:2010; EN55024:2010; EN50121-4:2006, EN61000-6-1:2007;
EN 61000-6-2:2005, EN61000-6-3:2007+A1:2011, EN61000-64:2007+A1:2011, AS/ NZS CISPR22:2009+A1:2010, CFR47 FCC
part15B
Security
Certifications
Power Supply
Power over Ethernet IEEE 802.3af
Power Consumption
Typ. 3.3 W
Protection Classes
IP66
IK06, IK10 with Vandalism Kit
Ambient Temperature
–30 to 50 °C/–22 to 104 °F
Dimensions/Weight
Diameter x height: 160 x 48 mm/6.30 x 1.89 in; weight: approx. 350 g
Standard Delivery
Housing (high-resistance composite, PBT) white, mounting supplies, mounting wrenches, 50 cm/20 in patch cable, software,
MicroSD card (SDXC, SDHC installed)
Dimensions
Cavity Wall Installation Set
Q26 without accessories
24.1 mm/
0.95 in
48 mm/1.89 in
ø 160 mm/6.30 in
Clamping range
6 to 22 mm/
0.24 to 0.87 in
ø 180 mm/7.09 in
On-Wall Set 10°
74 mm/
2.91 in
85 mm/3.35 in
On-Wall Set
ø 166 mm/6.54 in
ø 160 mm/6.30 in
Outdoor Wall Mount
125 mm/4.92 in
53 mm/2.09 in
Vandalism Kit
ø 160 mm/6.30 in
201 mm/7.91 in
216 mm/8.50 in
Drilling Template Without Accessories
100 mm/3.94 in
100 mm/3.94 in
ø 5.5 mm/0.22 in
m
m
1.4
7 in
5
/5.
14
Installation with mounting ring
(without accessories)
Camera without
accessories
On-Wall Set/
On-Wall Set 10°
Cavity Wall Installation Set
Outdoor Wall Mount
Pole Mount
Manuals and Drilling Templates:
www.mobotix.com > Support > Manuals > IP Camera Systems > Hemispheric Q26
MOBOTIX, the MX logo, MxControlCenter, MxEasy, MxPEG and MxActivitySensor are trademarks of
MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to
change without notice • MOBOTIX does not assume any liability for technical or editorial errors or omissions
contained herein • All rights reserved • © MOBOTIX AG 2017
Declaration of Conformity: www.mobotix.com > Support > MxMedia Library > Certificates
MOBOTIX AG
Kaiserstrasse
D-67722 Langmeil
Tel.: +49 6302 9816-103
Fax: +49 6302 9816-190
[email protected]
www.mobotix.com
">
