advertisement
V14.1.00
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer.
©July 2014
Trademarks
Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:
• Off Mode < 0.5W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1.
This device may not cause interference.
And
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
IV
Preface
FCC RF Radiation Exposure Statement:
1.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1.
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2.
Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3.
Do not use the telephone to report a gas leak in the vicinity of the leak.
4.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
5.
This product is intended to be supplied by a Listed Power Unit according to the model’s requirements:
• Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 2.1A (40W) minimum.
VI
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.
Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
2.
Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on any surface that will block the
Vents/Fan Intakes.
VII
Preface
3.
Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4.
Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all programs.
Do not turn off any peripheral devices when the computer is on.
Do not disassemble the computer by yourself.
Perform routine maintenance on your computer.
5.
Take care when using peripheral devices.
Use only approved brands of peripherals.
Unplug the power cord before attaching peripheral devices.
VIII
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
Power Safety
Warning
Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).
You must also remove your battery in order to prevent accidentally turning the machine on. Before removing
the battery disconnect the AC/DC adapter from the computer.
IX
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.
• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
X
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
XI
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply and then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
XII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.
Check that the battery pack and any spares are fully charged.
2.
Power off the computer and peripherals.
3.
Close the display panel and make sure it’s latched.
4.
Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.
The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
6.
Put the notebook in its carrying bag and secure it with the bag’s straps.
7.
If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.
8.
Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
XIII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XIV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XV
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.
XVI
Preface
Contents
Quick Start Guide
XVII
Preface
XVIII
Preface
Features & Components
Power Management
XIX
Preface
Drivers & Utilities (Win 8.1)
XX
Preface
BIOS Utilities
XXI
Preface
Modules & Options
XXII
Preface
Troubleshooting
Interface (Ports & Jacks)
Control Center
XXIII
Preface
Intel Video Driver Controls
Specifications
XXIV
Preface
Windows 7
XXV
Preface
XXVI
Preface
XXVII
Preface
XXVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, Multi-in-1 card reader), TouchPad & Mouse & Audio.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN and Combo Bluetooth & WLAN
modules (some of which may be optional depending on your purchase configuration).
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.
• Appendix B Information on Control Center.
• Appendix C Information on the Video driver controls.
• Appendix D The computer’s specification.
• Appendix E Information on the Windows 7 operating system.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to
“What to Install” on page 4 - 1
“BIOS Utilities” on page 5 - 1
in the remainder of the User’s
Manual. You may also find the notes marked with a
of interest to you.
Beginners and Non-Advanced Users
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see
(Ports & Jacks)” on page A - 1
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the
Preface
.
1 - 2 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in
“Drivers & Utilities (Win 8.1)” on page 4 - 1
. Drivers are programs which act as an interface between
the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you);
for installation instructions.
Ports and Jacks
“Interface (Ports & Jacks)” on page A - 1
for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1
Overview 1 - 3
1
Quick Start Guide
System Startup
1.
Remove all packing materials, and place the computer on a stable surface.
2.
Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3.
Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (make sure you use the adapter when first
setting up the computer, as to safeguard the computer during shipping the battery will be locked to not power the system until first connected to the AC/DC adapter).
4.
Use one hand to raise the lid/LCD to a comfortable viewing angle (do not exceed 130 degrees); use the other hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).
130
°
Shutdown
Note that you should always shut your computer down by choosing the Shut Down command in Win-
dows (see page
). This will help prevent hard disk or system problems.
Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In
1 - 4 System Startup
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 operating system is supported.
Note: In order to run Windows without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Windows Versions
Note that the information included on the following pages is for Windows 8.1 (64-bit) only. See
for information on the drivers and utilities for Windows 7 (64-bit) only.
Windows OS
In order to run Windows 8.1 (64-bit) or Windows 7 (64-bit with Service Pack 1) without limitations or decreased performance, your computer requires a minimum 2GB of system memory (RAM).
1
Model Differences
Note that though your computer may look slightly different from that pictured throughout this manual, all ports, jacks and general functions are the same for all design styles.
System Startup 1 - 5
1
Quick Start Guide
Figure 1 - 2
LCD Panel Open
1.
Built-in PC Camera
2.
PC Camera LED
3.
Built-In Microphone
4.
LCD*
5.
Power Button
6.
Keyboard
7.
Touchpad & Buttons
System Map: LCD Panel Open
2
1
3
4
5
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN, Bluetooth and
3G/4G modules) are OFF
(or the system is in Air-
plane Mode) if you are using the computer aboard
6
7
Note that the Touchpad and
Buttons has a valid operational area indicated within the dotted lines above.
1 - 6 System Map: LCD Panel Open
7
Quick Start Guide
LED Indicators
The LED indicators on the computer display helpful information about the current status of the computer.
Icon Color Description
1
Orange
Green
Blinking Green
Orange
Green
Blinking Orange
Off
Green
Green
DC Power is Plugged In
The Computer is On
The Computer is in Sleep Mode
The Battery is Charging
The Battery is Fully Charged
The Battery Has Reached Critically Low Power Status
Battery Charging has been Disabled
Hard Disk Activity
Airplane Mode is ON (the WLAN, Bluetooth & 3G/4G Modules are OFF)
Table 1 - 1 - LED Indicators
LED Indicators 1 - 7
1
Quick Start Guide
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.
NumLk & ScrLk
Hold down the Fn Key and either NumLk or
ScrLk to enable number or scroll lock, and check the LED indicator for status.
Keyboard
The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.
Function Keys
Play/Pause Key
Numerical Keypad
NumLk &
ScrLk Keys
Fn Key Menu/Application Key
Windows Logo Key
Figure 1 - 3 - Keyboard
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
1 - 8 Keyboard
Quick Start Guide
Keyboard Shortcuts
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.1.
Windows Logo
Key +
Description
Tap Winkey
C
D
E
R
Z
L
P
F
I
K
Toggle between the Start screen and the foremost running app or the
Windows Desktop
Display Charms menu
Switch to the Windows Desktop and toggle show Desktop
Switch to the Windows desktop and launch Windows Explorer with
Computer displayed
Display file Search
Open the Settings charm
Open the Connect charm
Lock the computer and display the Lock screen
Display the Second Screen menu (see
Figure 1 - 17 on page 1 - 25
)
Switch to the Windows Desktop and display the Run dialog box
Access the Customize Bar (see
Figure 1 - 12 on page 1 - 20
)
Table 1 - 2 - Keyboard Shortcuts
Windows Logo
Keyboard Shortcut
Use the Windows logo
bination to switch from the Start screen to the Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app is running you can use the Menu/Application key on the keyboard to act as a mouse right-click. In the Start screen this function is useful to quickly display Cus-
tomize Apps.
Keyboard 1 - 9
1
1
Quick Start Guide
Function/Hot Key Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; some visual indicators are available when the hot key utility is installed.
Keys Function Keys Function
Fn +
Fn + Play/Pause (in Audio/Video Programs) Brightness Decrease/Increase
Fn +
Fn +
Fn +
TouchPad Toggle
Turn LCD Backlight Off
(Press a key to or use TouchPad to turn on)
Mute Toggle
Fn +
Fn +
Fn +
PC Camera Power
Toggle
Airplane Mode Toggle
Number Lock Toggle
Fn +
Fn +
Fn +
Sleep Toggle Scroll Lock Toggle
Fn +
Volume Decrease/Increase Caps Lock Toggle
Display Switch Menu
Fn +
Fan Control Toggle
Automatic Fan Control /
Full Power
Table 1 - 3
-
Function & Hot Key Indicators
1 - 10 Function/Hot Key Indicators
Quick Start Guide
Control Center
When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or
double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Con-
trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/touch pad on/off (see
for full details).
Control Center Access
To run the Control Center press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar.
Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).
1
Figure 1 - 4 - Control Center
Control Center 1 - 11
1
Quick Start Guide
Figure 1 - 5
Front & Left Views
1.
LED Indicators
2.
External Monitor
Port
3.
Vent/Fan Intake/
Outlet
4.
HDMI-Out Port
5.
USB 3.0 Port
6.
Microphone-In
Jack
7.
Headphone-Out
Jack
System Map: Front & Left Views
1
1
2 3
4
5
6 7
USB 3.0 Port OR USB 2.0 Port
This model includes 1 * USB 3.0 port and 2 * USB 2.0 ports. The USB 3.0 port is denoted by its
blue color
; the USB 2.0 ports are colored black.
Optical Device Drives
To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports.
HDMI Port
Note that the HDMI Port supports video and audio signals to attached external displays.
1 - 12 System Map: Front & Left Views
System Map: Right & Rear Views
5 5
4
3 2
1
6
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial dis-
“Battery Information” on page 3 - 14
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
Quick Start Guide
Figure 1 - 6
Right & Rear Views
1.
Security Lock
Slot
2.
DC-In Jack
3.
RJ-45 LAN Jack
4.
Multi-in-1 Card
Reader
5.
2 * USB 2.0 Ports
6.
Battery
USB 3.0 Port OR USB
2.0 Port
This model includes 1 *
USB 3.0 port and 2 *
USB 2.0 ports. The USB
3.0 port is denoted by its
blue color
; the USB 2.0
ports are colored black.
1
System Map: Right & Rear Views 1 - 13
1
Quick Start Guide
Figure 1 - 7
Bottom View
1.
Battery
2.
Vent/Fan Intake/
Outlet
3.
Speakers
System Map: Bottom View
1
2
2
3 3
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Bottom Cover Removal Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.
If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.
1 - 14 System Map: Bottom View
Quick Start Guide
1
Removing/Inserting the Battery
Follow the procedure below if you need to remove the battery.
1.
Turn the computer off, and turn it over.
2.
Slide the latch
1
in the direction of the arrow.
3.
Slide the latch
2
in the direction of the arrow, and hold it in place.
4.
Slide the battery out in the direction of the arrow
3
.
5.
Reinsert the battery as illustrated below
4
.
6.
Make sure the latches are returned to the lock position
5
.
3
2 1
5
4
Figure 1 - 8
Battery Removal &
Insertion
Removing/Inserting the Battery 1 - 15
1
Quick Start Guide
Windows Versions
Note that the information included on the following pages is for the latest updated version of Windows 8.1 only.
Make sure you enable
Windows Update in order to get all the latest security updates etc.
(see
“Windows Update” on page 4 - 8
).
Windows 8.1 Control Panel
Throughout this manual you will see an instruction to open the Control Panel.
R ight-click the lower left hot corner to bring up the context menu (or use the Win-
dows Logo Key
+ X key combination) and select Control Panel in both the
Desktop app or Start screen.
Desktop app
Start Screen
Move the mouse to the bottom left of the screen and right-click to access the menu.
Figure 1 - 9 - Windows Context Menu
1 - 16 Windows 8.1 Control Panel
Quick Start Guide
The Control Panel can be accessed in a number of ways in Windows 8.1.
• Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type
Control Panel and select it from the results to the left.
• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.
• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows
Charms Bar and select Control Panel from the menu.
• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).
• Right-click the Start button to bring up the menu and select Control Panel (see
Figure 1 - 10 on page 1
- 18
).
Keyboard Shortcut to Control Panel
You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key
and R
to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
1
Windows 8.1 Control Panel 1 - 17
1
Quick Start Guide
Display Most
Recently Used
Apps
If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.
To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.
Right-click the Start button in the Desktop app (or use the Windows Logo Key
+ X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager,
Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
Move the mouse to the bottom left of the screen and right-click the Start button to access the menu.
Figure 1 - 10 - Advanced Context Menu (Right-Click Start Button)
1 - 18 Windows 8.1 Control Panel
Quick Start Guide
Windows 8.1 Start Screen & Desktop
The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or
Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps.
1
Desktop App
Figure 1 - 11 - Windows Start Screen
Windows 8.1 Start Screen & Desktop 1 - 19
1
Quick Start Guide
Apps & Tiles
The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.
Accessing Pining/Unpinning All Apps
You can add and remove the tiles for apps and control panels in the Start screen. Right-click on an app to bring up the context menu and you pin the App to (or unpin from) the Start screen, or to the taskbar.
Click the arrow at the bottom of the screen to access All Apps
Figure 1 - 12 - Apps
1 - 20 Windows 8.1 Start Screen & Desktop
Quick Start Guide
Desktop Application
When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.
1
Move the mouse to the bottom left of the screen and click to switch back to the Start screen.
Figure 1 - 13 - Desktop
Windows 8.1 Start Screen & Desktop 1 - 21
1
Quick Start Guide
The Charms Bar
The right side of the screen (Start or Desktop) displays the Charms Bar. The Charms Bar contains the Search,
Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Move the mouse to the top/lower right icons to activate the Charms Bar
Move the mouse over a Charms Bar icon to activate the menu
Move the mouse to the top/lower right icons to activate the Charms Bar
Figure 1 - 14 - Start Screen with Charms Bar
1 - 22 Windows 8.1 Start Screen & Desktop
Quick Start Guide
Charms Bar Items
• Search : You can search for any file, application, Apps and control panel settings with instantaneous results.
• Share
: This button is used to share information with people via mail or social networks.
• Start
: Click to bring up the Start screen (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen).
• Devices
: Click this button to change connected peripheral device settings e.g. an external display.
• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).
1
Charms Bar - TouchPad Access
To quick access the Charms Bar using the TouchPad:
1.
Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).
2.
Move your finger across to the left on to the TouchPad.
3.
The Charms Bar will then pop-up.
Figure 1 - 15 - Settings Menu
Windows 8.1 Start Screen & Desktop 1 - 23
1
Quick Start Guide
Windows 8.1 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the task-
bar (system tray). In Windows 8.1 the taskbar can be directly accessed from the Desktop application; if you are in the Start screen you will need to move the cursor to the bottom of the screen to display the taskbar.
The taskbar is displayed at the bottom of the screen, and you can see the notification area (system tray) of the taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the course of this manual can be accessed from here.
Figure 1 - 16 - Taskbar & Notification Area (System Tray)
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see
“Accessing
Pining/Unpinning All Apps” on page 1 - 20
).
1 - 24 Windows 8.1 Start Screen & Desktop
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows when running the Desktop app (see
“Desktop Application” on page 1 - 21
).
It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see
).
To Configure Displays from Devices (Charms Bar):
1.
Attach your display to the appropriate port, and turn it on.
2.
Go the Charms Bar, select Devices.
3.
Click Project (you may need to click Second Screen).
4.
Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen
only.
1
Figure 1 - 17 - Devices (Project)
Video Features 1 - 25
1
Quick Start Guide
To access Display (Control Panel) and Screen Resolution in Windows 8:
1.
Go to the Control Panel.
2.
Click Display (icon) - In the Appearance and Personalization category.
3.
Adjust resolution.
1
2
3
Right-Click Desktop
App
1.
You can right-click the desktop and select Screen reso-
lution
1
(
Figure 1 -
18
).
2.
Use the dropbox to select the screen
Resolution
2
(
Figure 1 - 18
).
3.
Click Advanced
settings
3
(
Figure
1 - 18
) to bring up the
Advanced properties tabs.
Figure 1 - 18 - Screen Resolution
1 - 26 Video Features
Quick Start Guide
To access the Intel(R) HD Graphics Control Panel:
1.
Click Advanced settings
3
(
Figure 1 - 18 on page 1 - 26
) in the Screen Resolution control panel in Win-
dows.
2.
Click the Intel(R)... tab and click Graphics Properties (button)
4
(
Figure 1 - 19 on page 1 - 27
) .
OR
3.
Right-click the desktop and select Graphics Properties from the menu.
OR
4.
Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
1
4
Figure 1 - 19 - Intel Graphics Control Panel
Video Features 1 - 27
1
Quick Start Guide
Power Options
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set-
tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/
Sleep to the menu - see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 10
context menu (Shut down or sign out) shut the computer down/restart etc.
Power Button Start Screen Desktop App Start Screen
Charms Bar
1 - 28 Power Options
Figure 1 - 20 - Shut Down/Restart
Quick Start Guide
Running Apps
To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Set-
tings are compatible with the system requirements.
Screen Resolution Settings
1.
Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).
2.
Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).
Screen Resolution for Apps
(Windows 8.1)
The minimum resolution in which Apps will run is 1024x768.
The minimum resolution required to support all the features of
Windows 8 (including multitasking with snap) is 1366x768.
These specs are the minimum screen resolution that supports all the features of Windows 8.1 on a useful physical size.
1
Figure 1 - 21 - Screen Resolution
Running Apps 1 - 29
1
Quick Start Guide
User Account Control Settings
If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off.
To check whether the UAC is on or off, follow the instructions below.
1.
Open the Control Panel.
2.
Click on User Accounts and then click on Change User Account Control settings (or click System and
Security and click Change User Account Control Settings under Action Center).
3.
If the slider is in the Never notify position, then the UAC is disabled.
4.
To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes
to my computer (default) position, and then click OK.
1 - 30 Running Apps
Figure 1 - 22 - User Account Control
Chapter 2: Features & Components
Features & Components
Overview
Read this chapter to learn more about the following main features and components of the computer:
• Hard Disk Drive/Solid State Drive/
2
Overview 2 - 1
2
Features & Components
Bottom Cover
Removal Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.
If you need to replace/ remove the hard disk for any reason, please contact your distributor/supplier for further information.
Hard Disk Drive/Solid State Drive
The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data in the computer. The hard disk can be taken out to accommodate other serial (SATA)
for specification information), however you will need to contact your distributor/supplier to do this in order to avoid violating the terms of your warranty.
The solid state drive is a factory option for this computer model.
2 - 2 Hard Disk Drive/Solid State Drive
Features & Components
Multi-In-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see
• MMC (MultiMedia Card) / RSMMC
• SD (Secure Digital) / Mini SD / SDHC / SDXC
*Note: The PC adapters are usually supplied with these cards.
2
1
Figure 2 - 1
Right View
1.
Card Reader
Multi-In-1 Card Reader 2 - 3
2
Features & Components
Touchpad Active
Areas
Note that the pointing
active area is clearly defined from the but-
ton active area as illustrated.
Touchpad and Buttons/Mouse
The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Touchpad Sensitivity
The mouse button zones at the bottom of the pad are defined by the line at the bot-
tom of the pad, and the left and right buttons are divided roughly down the middle as illustrated below. The active area of the touchpad is that defined in the diagram below. Press the left button zone for a left click, and right button zone for a right click action.
Figure 2 - 2
Touchpad
Sensitivity
2 - 4 Touchpad and Buttons/Mouse
Features & Components
Once you have installed the Touchpad driver (see
can configure the functions by double-clicking the Touchpad driver icon in the notification area of the taskbar. You may then configure the Touchpad tapping, buttons, scrolling (see sidebar), pointer motion and sensitivity options to your preferences.
Touchpad Scrolling
This computer model series may feature different
Touchpad versions.
These Touchpads may differ in their vertical scrolling function in most scrollable windows.
Some Touchpads require sliding the finger up and down on the right of the
Touchpad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the
Touchpad to scroll the window.
2
Figure 2 - 3
Mouse Properties
Touchpad and Buttons/Mouse 2 - 5
2
Features & Components
Show Video
You can get a clearer view of the gestures involved by clicking the
Show Video option for each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Set-
tings left tree menu and click the Show Video button to see the demonstration video.
For more details on any of the gestures see the help in the lower part of the right menu window.
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1.
Click Start, and click Control Panel (or point to Settings and click Control Panel).
2.
Click Mouse (Hardware and Sound).
3.
Click Device Settings (tab) and click Settings.
4.
Use the menu tree on the left to access the user configurable settings.
Figure 2 - 4
Mouse Properties -
Device Settings
2 - 6 Touchpad and Buttons/Mouse
Features & Components
Disabling the Touchpad
If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination.
You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g. a USB mouse) is attached.
1.
Go to the Mouse Properties control panel.
2.
Click to select Device Settings (tab).
3.
Click to place a check in the “Disable internal pointing device when external
USB pointing device is attached” check box.
4.
Click OK to save the setting.
2
Figure 2 - 5
Mouse Properties
(Disable Touchpad)
Touchpad and Buttons/Mouse 2 - 7
2
Features & Components
Figure 2 - 6
Scrolling Gesture
Scrolling
The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the
Touchpad surface and slide both fingers in the direction required (in a straight continuous motion).
Mouse Driver
If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.
Be sure to check the device’s user documentation for details.
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the Touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.
Figure 2 - 7
Zooming Gesture
2 - 8 Touchpad and Buttons/Mouse
Features & Components
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Figure 2 - 8
Rotating Gesture
2
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
Figure 2 - 9
Flick/Press
Gesture
Touchpad and Buttons/Mouse 2 - 9
2
Features & Components
Audio Features
Volume Adjustment
The sound volume level can be set using the volume control in the Set-
tings
menu in the
Charms Bar.
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume
icon in the taskbar or the audio slider in the Settings menu (see sidebar).
Figure 2 - 10
Realtek Audio
Manager
2 - 10 Audio Features
Right-click the icon to access the menu above.
Features & Components
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1.
Go to the Control Panel.
2.
Click Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager.
3.
Click Microphone Effects (tab) in Microphone (tab), and then click to select
Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.
4.
Click OK to close the control panel and save the settings.
2
Figure 2 - 11
Realtek Audio
Manager -
Recording Setup
Audio Features 2 - 11
2
Features & Components
2 - 12
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
• Configuring the Power Buttons
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.
OS Note
Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.
(Note: All pictures used on the following pages are from the Windows
8.1 OS.)
Power Options
Power management in
Windows is configured from Power Options
(Hardware and
Sound), which can be accessed from the Con-
trol Panel (see page
3
Overview 3 - 1
3
Power Management
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1.
Attach the AC/DC adapter to the DC-In jack on the right of the computer, connect the AC power cord to the AC/DC adapter and then plug the AC power cord into an outlet (make sure you use the adapter when first setting up the computer, as to safeguard the computer during shipping the battery will be locked to not power the system until first connected to the AC/DC adapter).
2.
Raise the lid/LCD to a comfortable viewing angle.
3.
Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see
We recommend that you do not remove the battery. For more information on the battery, please refer to
“Battery Information” on page 3 - 14
3 - 2 The Power Sources
Turning On the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Button as Stand by or Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the
system into Stand by or Hibernate mode (see your OS’s documentation, or
“Configuring the Power Buttons” on page 3 - 9
Power Management
3
Turning On the Computer 3 - 3
3
Power Management
Shutting the Computer Down
Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Shut down
or sign out item in the Context Menu (right-click the lower left corner of the screen to bring up the menu).
You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If you want to add Hibernate/Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 10
.
Charms Bar Desktop App Start Screen
Figure 3 - 1
Shut Down/Restart
3 - 4 Shutting the Computer Down
Power Management
Power Plans
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Resuming
Operation
See
Table 3 - 1, on page 3 - 11
for information on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in order to protect your data.
3
Figure 3 - 2
Power Plan
Advanced Settings
Power Plans 3 - 5
3
Power Management
Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.
Figure 3 - 3
Power Plans
Click to Show/Hide additional power plans
3 - 6 Power Plans
Power Management
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.
To add Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power
Menu” on page 3 - 10
.
Wake On LAN
Support
(Windows 8)
Wake-On-LAN is only supported from Sleep or
Hibernate states in
Windows 8.
If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hiber-
nate.
Wake-On-LAN is not supported from Shutdown states in Win-
dows 8.
3
Power-Saving States 3 - 7
3
Power Management
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the
Power Menu see
“Adding Hibernate/Sleep to the Power Menu” on page 3 - 10
.
Shut down
You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.
Figure 3 - 4
Power Menu
3 - 8 Power-Saving States
Power Management
Configuring the Power Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Password
Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can disable this setting from the
Power Options menu by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that are currently unavail-
able).
Figure 3 - 5
Power Options
Define Power
Buttons
3
Configuring the Power Buttons 3 - 9
3
Power Management
Adding Hibernate/Sleep to the Power Menu
Add Hibernate/Sleep to the Power Menu as follows.
1.
Go to the Power Options (Hardware and Sound) control panel.
2.
Click Choose what the power buttons do.
3.
Click “Change settings that are currently unavailable” .
4.
Click to put a check in the Hibernate/Sleep box under Shutdown settings.
5.
Click Save Changes and close the control panel.
Figure 3 - 6
Power Options
Define Power
Buttons - Shutdown
Settings
3 - 10 Configuring the Power Buttons
Power Management
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status To Resume
Power Off
Sleep
Off
Blinking Green
Press the Power Button
Press the Power Button
Press the Sleep Button (Fn + F4 Key Combo)
Hibernate
Display Turned Off
Off (battery)
Orange (AC/DC adapter)
Green
Press the Power Button
Press a Key or Move the Mouse/Touchpad
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
Table 3 - 1
Resuming
Operation
Closing the Lid
If you have chosen to send the computer to
Sleep when the lid is closed, raising the lid will wake the system up.
3
Configuring the Power Buttons 3 - 11
3
Power Management
Power Conservation
Modes
The Energy Star setting will result in maximum power saving, but with the possible loss of some performance.
Setting the mode to Bal-
ance will give power saving matched with performance.
Performance will give optimum computer performance but with less power conservation.
Note that the Energy
Star setting will put the display into sleep after no more than 15 minutes of user inactivity.
Power Conservation Modes
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:
1.
Press the Fn + Esc key combination to toggle the Control Center on/off.
2.
Click either the Performance, Balanced or Energy Star button.
Figure 3 - 7
Control Center
3 - 12 Configuring the Power Buttons
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination from almost any of the Win-
dows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log
off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management
3
Figure 3 - 8
Ctrl + Alt + Delete
Menu
To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to perform the function selected.
Configuring the Power Buttons 3 - 13
3
Power Management
Low Battery
Warning
When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.
Battery Information
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see
Figure
3 - 3 on page 3 - 6
).
Click the battery icon in the notification area to see the current battery level and charge status.
Figure 3 - 9
Battery Icon
(Notification Area) &
Battery Advanced
Settings
3 - 14 Battery Information
Power Management
Removing the Battery
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see below.
1.
Turn the computer off, and turn it over.
2.
Slide the latch
1
in the direction of the arrow.
3.
Slide the latch
2
in the direction of the arrow, and hold it in place.
4.
Slide the battery out in the direction of the arrow
3
.
5.
Reinsert the battery as illustrated below
4
.
6.
Make sure the latches are returned to the lock position
5
.
2 1
3
Bottom Cover
Removal Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.
If you need to replace/ remove the hard disk/
RAM/optical device etc., for any reason, please contact your distributor/ supplier for further information.
5
Figure 3 - 10
Battery Removal
4
3
Battery Information 3 - 15
3
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Conserving Battery Power
• Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth, modem or communication applications when they are not being used (e.g. put the system in Airplane Mode).
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
Figure 3 - 11
Windows Mobility
Center
3 - 16 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days. You can toggle battery charging on/off by using the Fn + 6 key combination.
New Battery
Always completely discharge, then fully charge, a new battery (see
for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. Refer to
“LED Indicators” on page 1 - 7
for information on the battery charge status, and to
“Battery Information” on page 3 - 14
for more information on how to maintain and properly
recharge the battery pack.
Power Management
3
Battery Information 3 - 17
3
Power Management
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.
3 - 18 Battery Information
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1.
Save and close all files and applications.
2.
Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Figure 3 - 12
Power Plan Create
Battery Information 3 - 19
3
Power Management
3.
Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings.
Figure 3 - 13
Change Plan
Settings / Change
Advanced Power
Settings
3 - 20 Battery Information
4.
Scroll down to Battery and click + to expand the battery options.
5.
Choose the options below (click Yes if a warning appears):
Power Management
3
Figure 3 - 14
Power Options
Advanced Settings -
Battery
• Low battery levels = 0%
• Critical battery Levels = 1%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
Battery Information 3 - 21
3
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
3 - 22 Battery Information
Drivers & Utilities (Win 8.1)
Chapter 4: Drivers & Utilities (Win 8.1)
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.
What to Install
The
Device Drivers & Utilities + User’s Manual
disc contains the drivers and util-
ities necessary for the proper operation of the computer.
lists what you need to install and it is very important that the drivers are installed
by the method outlined in this chapter, and in the order indicated.
Note that the information included on the following pages is for Windows 8.1 only.
“Drivers & Utilities (Windows 7)” on page E - 8
for information on drivers and
utilities for the Windows 7 (64-bit with Service Pack 1) operating system.
Module Driver Installation
The procedures for installing drivers for the Wireless LAN and Combination Blue-
tooth & WLAN modules are provided in
“Modules & Options” on page 6 - 1
Driver Installation &
Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a work-
ing power source.
Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems
(note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
4
What to Install 4 - 1
4
Drivers & Utilities (Win 8.1)
Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive.
2.
Click the message “Tap to choose what happens with this disc.”
3.
Click Run autorun.exe.
4.
Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.
4 - 2 Driver Installation
Figure 4 - 1
- Drivers Installer Screen 1
Drivers & Utilities (Win 8.1)
5.
Check the driver installation order from
(the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
6.
Click to select the driver you wish to install, (you should note down the drivers as you install them).
7.
Follow the instructions for each individual driver installation procedure as listed on the following pages.
4
Figure 4 - 2
- Install Drivers
Driver Installation 4 - 3
Drivers & Utilities (Win 8.1)
4
Win 8.1 Driver - System Required
Page #
Win 8.1 Driver (Other / Options)
Intel® Rapid Storage Technology
(No driver required)
(No driver required)
Page #
Table 4 - 1
- Driver Installation
All drivers provided are for Windows 8.1 (64-bit).
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
4 - 4 Driver Installation
Manual Driver Installation
Click Browse CD/DVD (button) in the Drivers Install-
er application and browse to the executable file in the appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See
“Windows Update” on page 4 -
9
for instructions.
Drivers & Utilities (Win 8.1)
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1.
Go to the Control Panel).
2.
Double-click Device Manager (Hardware and
Sound > Devices and Printers > Device
Manager).
3.
Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4.
Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
4
Driver Installation 4 - 5
4
Drivers & Utilities (Win 8.1)
User Account Control
If a User Account Control prompt appears as part of the driver installation procedure, click Continue or
Allow, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this
driver software anyway” or “Install” to continue the installation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” during the installation procedure (other than when out-
lined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter
(and in Chapter 6 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver.
Make sure any modules (e.g. WLAN or Bluetooth) are
ON before installing the appropriate driver.
4 - 6 Driver Installation
Drivers & Utilities (Win 8.1)
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button).
LAN
1.
Click 3.Install LAN Driver > Yes.
2. Click Next > Install.
3. Click Finish.
Chipset
1.
Click 1.Install Chipset Driver > Yes.
2. Click Next.
3. Click the Accept button to agree to the license.
4. Click Install.
5. Click Finish.
Video (VGA)
1.
Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Note: After installing the video driver go to the Dis-
play/Display Settings control panel to adjust the video settings to the highest resolution.
CardReader
1.
Click 4.Install Cardreader Driver > Yes.
2. Click Finish.
Touchpad
1.
Click 5.Install Touchpad Driver > Yes.
2. Click Next.
3. Click the button to accept the license agreement and click Next.
4. Click Finish > Restart Now to restart the computer.
4
Driver Installation 4 - 7
4
Drivers & Utilities (Win 8.1)
Hot Key
1.
Click 6.Install Hotkey AP > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Audio
1.
Click 9.Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Airplane
Note: Do not use Update Driver in Device Manager to install the Airplane Mode driver.
1.
Click 7.Install Airplane Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My
Computer), and click Option Drivers (button) to access the optional driver menu.
MEI Driver
1.
Click 8.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish.
4 - 8 Driver Installation
Drivers & Utilities (Win 8.1)
Windows Update
After installing all the drivers make sure you enable Win-
dows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1.
Go to the Control Panel.
2.
Click Windows Update (System and Security/
Security).
3.
Click Check for updates (button).
4.
The computer will now check for updates (you need to be connected to the internet).
5.
Click Install now (button) to begin checking for the updates.
6.
Click Install updates (button) to install the updates.
4
Driver Installation 4 - 9
4
Drivers & Utilities (Win 8.1)
Optional Drivers
See the pages indicated for the driver installation procedures for any modules included in your purchase option.
Figure 4 - 3
- Drivers Installer (Options)
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
4 - 10 Driver Installation
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s
BIOS.
BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
5
Overview 5 - 1
5
BIOS Utilities
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct mistakes, return to Opti-
mized Defaults with
<F3>.
UEFI Boot & POST
When UEFI Boot is enabled, then the prompts to press F2 or F7 will
not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
The Setup Utility
Each time you turn on the computer the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup). If the Boot Logo is enabled the F2 on screen will be highlighted to illustrate that the system is processing the request during the POST (or press F7 for boot options). If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
To see the boot options press F7 and choose your preferred boot device.
5 - 2 The Setup Utility
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options.
Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
BIOS Utilities
5
The Setup Utility 5 - 3
5
BIOS Utilities
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options.
Setup Screens
The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
Figure 5 - 1
Navigation Menu
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the upper right side of each screen explains the highlighted item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
5 - 4 The Setup Utility
Main Menu
BIOS Utilities
Figure 5 - 2
Main Menu
5
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
Main Menu 5 - 5
5
BIOS Utilities
SATA Port # (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a optical Device/
HDD on the computer’s SATA Ports.
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
MB Series / BIOS Revision / KBC/EC firmware Revision
This item contains information on the BIOS version etc., and is not user configurable.
5 - 6 Main Menu
Advanced Menu
BIOS Utilities
Figure 5 - 3
Advanced Menu
5
SATA Mode (Advanced Menu)
The SATA (Serial ATA) control is configured to operate in AHCI (Advanced Host
Controller Interface) mode.
Advanced Menu 5 - 7
5
BIOS Utilities
UEFI Boot
When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
Boot Logo (Advanced Menu)
Use this menu item to enable/disable the Boot Logo screen at system startup if you
have not enabled UEFI Boot. If you disable the Boot Logo you will not see the F2
Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot
Option functions.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
5 - 8 Advanced Menu
Security Menu
BIOS Utilities
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.
These settings do not affect your machine or network passwords which will be set in your software OS.
5
Figure 5 - 4
Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
Security Menu 5 - 9
5
BIOS Utilities
Password Warning
If you set a boot password (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Set User Password (Security Menu)
You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Aptio Setup Utility cannot be modified in user mode.
Note: You can only set the user password after you have set the supervisor pass-
word.
Password on boot: (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.
5 - 10 Security Menu
Secure Boot (Security Menu)
Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have
“UEFI Boot (Boot Menu)” on page 5 - 16
). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy) or Custom (which enables you to make changes to the Key Management database).
BIOS Utilities
5
Security Menu 5 - 11
5
BIOS Utilities
TPM Configuration (Security Menu)
This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu
and select Enable to display the full TPM configuration menu (see
“Trusted Platform Module” on page 6 - 22
for details).
Figure 5 - 5
Security Device
Support
5 - 12 Security Menu
TPM State (Security Menu > Security Device Support Enabled)
Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer.
BIOS Utilities
Figure 5 - 6
TPM State (Enabled)
5
As the computer restarts press F2 to enter the BIOS again and go to the TPM Con-
figuration menu.
Security Menu 5 - 13
5
BIOS Utilities
Pending TPM operation (Security Menu > Security Device Support & TPM State
Enabled)
Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. You can manage the TPM
“TPM Management in Windows” on page 6 - 25
Figure 5 - 7
Pending TPM operation
(Enable Take
Ownership)
5 - 14 Security Menu
BIOS Utilities
Boot Menu
Figure 5 - 8
Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows
7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities. Item specific help on the right is available to help you move devices up and down the order.
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s
BIOS.
BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
Boot Menu 5 - 15
5
5
BIOS Utilities
Boot Option Priorities (Boot Menu)
Press Enter to access the menu, use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list (the selected device will be highlighted in white).
UEFI Boot (Boot Menu)
Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services. The Network Stack and IPV# PXE Support items will be enabled as an option under UEFI Boot.
5 - 16 Boot Menu
Exit Menu
BIOS Utilities
Figure 5 - 9
Exit Menu
5
Click Save Changes and Reset to save all changes made. Choosing to Discard
Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Exit Menu 5 - 17
5
BIOS Utilities
5 - 18
Modules & Options
Chapter 6: Modules & Options
Overview
This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
• Bluetooth & WLAN Combo Module
• Intel® Rapid Storage Technology
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
Bluetooth module(s)
are OFF (or the system is in Airplane Mode) if you are using the computer aboard aircraft
(see
6
Overview 6 - 1
6
Modules & Options
PC Camera Module
When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red
use the Camera app in Windows 8 to take pictures and capture video. Use the Fn +
“Function/Hot Key Indicators” on page 1 - 10
) to tog-
gle power to the PC Camera module.
6 - 2 PC Camera Module
PC Camera Audio Setup
If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows.
1.
Go to the Control Panel.
2.
Click Sound (Hardware and Sound) and click Recording (tab).
3.
Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled.
4.
Double-click Microphone (or select Properties from the right-click menu).
5.
Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required.
6.
Click OK and close the control panels.
Modules & Options
Figure 6 - 1
Audio Setup for PC
Camera
6
Right-click
PC Camera Module 6 - 3
6
Modules & Options
Figure 6 - 2
Camera App
Buttons
Exposure
Use the slider to adjust the Exposure level.
Camera App
1.
Run the Camera app from the Start screen by clicking on the Camera app icon
.
2.
The camera interface will display two buttons on the right side of the screen.
3.
The upper button to take still pictures.
is used to record video, and the lower button is used
4.
Right-click on the screen to bring up menu buttons at the bottom of the screen.
5.
These buttons enable you to access the camera roll (where captured pictures and video are displayed), set the timer (the time period before capture begins; 3 seconds, 10 seconds or Off) and set the exposure level using the slider to obtain the best results.
Figure 6 - 3
Camera Options
6 - 4 PC Camera Module
Camera Options
The Camera Options settings may be accessed as follows:
1.
Run the Camera app from the Start screen by clicking on the Camera app icon
.
2.
While the camera app is running access the Charms Bar (e.g. click Use the
Windows logo key + C key combination).
3.
Click Settings and then click Options.
4.
You can adjust the Photo Aspect Ratio, select the Microphone, Hide/Show grid lines and turn Location Info on or off from the Options panel.
Modules & Options
6
Figure 6 - 4
Camera Options
PC Camera Module 6 - 5
6
Modules & Options
Taking Pictures/Capturing Video
1.
Run the Camera app from the Start screen by clicking on the Camera app icon
.
2.
Right-click the screen and select the timer if you require a countdown before capture.
3.
Click the appropriate icon to take a picture or start video capture (if video capture begins a timer will appear in the bottom corner of the screen).
4.
To stop video capture click the main window again (or click the stop icon ).
5.
Captured photos and videos will be saved to a Camera Roll folder within the
Pictures folder.
Figure 6 - 5
Pictures - Camera
Roll
6 - 6 PC Camera Module
Modules & Options
Camera Roll
1.
Run the Camera app from the Start screen by clicking on the Camera app icon
.
2.
Right-click on the screen to bring up menu buttons at the bottom of the screen.
3.
Click Camera Roll.
4.
Click the arrows / (on either side of the screen) to browse through the captured photos/video, and back to the Camera app.
Editing Photos
1.
Clicking on a captured photo will bring up an app bar with a series of buttons.
Figure 6 - 6
Edit Buttons
(for Still Photos)
2.
The Camera button will take you back to the home screen of the camera app.
3.
Click Delete to remove any photo from the camera roll (you will be asked to click
Delete again to confirm the deletion).
4.
The Open With button will allow you to select a program with which to open the photo.
5.
You can click Set as Lock screen to set the photo as the lock screen picture.
6.
Clicking Slide Show will create a slide show of photos/video in the camera roll.
7.
Click Rotate to rotate the picture through 90 degrees.
8.
Use the handles to Crop any captured picture, and click Apply to make the changes (you can change the Aspect ratio by clicking the button and selecting an aspect ratio from the menu). You can Save a copy (create another copy of the
PC Camera Module 6 - 7
6
6
Modules & Options
photo with the edited changes), Update original (which changes the original picture permanently) or Undo any changes.
9.
Click the Edit button to bring up a full suite of tools to edit the photo.
10. Click on the menu headings on the left, and then click on the tool on the right to edit the photo as required.
Edit Menu Basic Fixes Light Color Effects
Figure 6 - 7
Editing Tools
11. After the editing process is completed right-click on the photo to Save a copy
(create another copy of the photo with the edited changes), Update original
(which changes the original picture permanently), Undo any changes or Cancel the editing.
6 - 8 PC Camera Module
Editing Photos
1.
Clicking on a captured video will bring up an app bar with a series of buttons.
Modules & Options
Figure 6 - 8
Edit Buttons
(for Video)
2.
Click Delete to remove any video from the camera roll (you will be asked to click
Delete again to confirm the deletion).
3.
The Open With button will allow you to select a program with which to run the
Video.
4.
Clicking Slide Show will create a slide show of photos/video in the camera roll.
5.
Click Trim to edit the video. Use the round buttons at either end of the slider to adjust the video length and click Save a copy to save the changes made.
Figure 6 - 9
Trim Video
(for Video Files)
Click to select and move the rounded buttons to edit the video.
6
PC Camera Module 6 - 9
6
Modules & Options
Video File Size
Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My
Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Note that the Windows 8.1 system requires a minimum of 16GB (32-bit) or 20GB
(64-bit) of free space on the C: drive system partition. In order to prevent system problems it is recommended that you move any large sized captured video file to a location other than the C: drive.
6 - 10 PC Camera Module
Modules & Options
Wireless LAN Module
If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver.
Make sure you install the drivers in the order indicated in
.
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN
& Bluetooth Combo modules.
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
Bluetooth module(s)
are OFF if you are using the computer aboard aircraft by putting the system in to Airplane
Mode (see
6
Wireless LAN Module 6 - 11
6
Modules & Options
3rd Party 802.11b/g/n Driver Installation
1.
Make sure the module is on and the system is not in Airplane Mode,
and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
1.Install WLAN Driver > Yes.
4.
Click Next.
5.
Click
Finish to restart the computer.
6. The operating system is the default setting for Wireless LAN control in
Windows (see page
6 - 13
Intel® WLAN Driver Installation
1.
Make sure the module is on and the system is not in Airplane Mode,
and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
1.Install WLAN Driver > Yes.
4.
Click in the check box to agree to the End User License Agreement and click
Install.
5.
Click
Finish.
6. The operating system is the default setting for Wireless LAN control in
Windows (see page
6 - 13
6 - 12 Wireless LAN Module
WLAN Configuration in Windows
You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins.
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
3.
A list of available access points will appear.
Modules & Options
6
Figure 6 - 10
WiFi Settings
(Charms Bar) &
Networks
Wireless LAN Module 6 - 13
Modules & Options
4.
Double-click an access point to connect to it (or click it and click Connect).
5.
Enter a network security key (password) if required, and click Next.
6.
You can choose to find other devices or not.
7.
When you are connected to the network access point it will display Connected
.
8.
Select any connected network and click Disconnect connected access point.
to disconnect from a
6
Figure 6 - 11
Networks
Connected /
Disconnect
9.
You can click the Airplane Mode button to turn the mode (including Bluetooth) On or Off.
10. Alternatively you can click the WiFi button to turn just the WiFi On or Off.
6 - 14 Wireless LAN Module
Desktop Mode
1.
Switch to the Windows Desktop (click the app or use the Windows logo key +
D key combination).
2.
Click the wireless icon in the notification area of the taskbar.
3.
A list of available access points will appear.
4.
Double-click an access point to connect to it (or click it and click Connect).
5.
Enter a network security key (password) if required, and click Next.
6.
You can choose to find other devices or not.
7.
Select any connected network and click Disconnect to disconnect from a connected access point.
Modules & Options
6
Figure 6 - 12
Windows Desktop
Taskbar Notification
Area WLAN
Connection
Wireless LAN Module 6 - 15
6
Modules & Options
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
Bluetooth module(s)
are OFF if you are using the computer aboard aircraft by putting the system in to Airplane
).
Bluetooth & WLAN Combo Module
If your purchase option includes the Combination Wireless LAN & Bluetooth
module (either Intel® or 3rd Party) then install the driver as instructed overleaf.
Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver.
Bluetooth Data Transfer
Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
6 - 16 Bluetooth & WLAN Combo Module
Modules & Options
3rd Party Bluetooth (V4.0) Combo Driver Installation
1.
Make sure the module is on and the system is not in Airplane Mode,
and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
2.Install Combo BT Driver > Yes.
4.
Click Next.
5.
Click
Finish to restart the computer.
6. See
“Bluetooth Configuration in Windows” on page 6 - 18
for configuration instructions.
Intel Bluetooth Combo Driver Installation
1.
Make sure the module is on and the system is not in Airplane Mode,
and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
2.Install Combo BT Driver > Yes.
4.
Click Next > Next.
5.
Click in the check box to accept the license and click Next.
6.
Click Next > Finish.
7. Click Yes to restart the computer.
8. See
“Bluetooth Configuration in Windows” on page 6 - 18
for configuration instructions.
High Speed Bluetooth
Data Transfer
The Combination Wire-
less LAN & Bluetooth
module supports high speed data transfer. However to achieve such transfer speeds, both de-
vices must support high speed data trans-
fer.
To obtain high speed data transfer make sure that both the WLAN and
Bluetooth modules are powered on.
Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer.
Bluetooth & WLAN Combo Module 6 - 17
6
6
Modules & Options
Bluetooth Headset
Stereo Setup
To setup a Bluetooth headset to support stereo audio see page
.
Bluetooth Configuration in Windows
You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (or the system is not in Airplane Mode) before configuration.
Desktop Mode
1.
Switch to the Windows Desktop (click the App or use the Windows logo key +
D key combination).
2.
Click the notification area of the taskbar and double-click the Bluetooth icon (or click and select Show Bluetooth Devices).
3.
The Bluetooth item in PC and Devices will appear.
OR
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click Change PC Settings.
3.
Select the Bluetooth item in PC and Devices.
Figure 6 - 13
Bluetooth Taskbar
Icon & Change PC
Settings (Charms
Bar -Settings)
6 - 18 Bluetooth & WLAN Combo Module
4.
Make sure that Bluetooth is turned on and a list of discovered devices will appear.
5.
Double-click the device you want to pair with the computer and click Pair.
Modules & Options
Figure 6 - 14
PC and Devices -
Bluetooth
6.
On first connection the computer will provide you with a pairing code to be entered onto the device.
Figure 6 - 15
Enter the Passcode
6
7.
Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
8.
Select a device and click Remove Device to disconnect from any device.
Bluetooth & WLAN Combo Module 6 - 19
6
Modules & Options
To Make your Computer Discoverable to Bluetooth Devices
1.
Switch to the Windows Desktop (click the app or use the Windows logo key +
D key combination).
2.
Click the notification area of the taskbar, click the Bluetooth icon and click
Open Settings.
3.
Click Options, and make sure that Allow Bluetooth devices to find this
computer check box (Discovery) has a check inside it.
4.
Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a check inside it, if you want to be notified when a
Bluetooth device wants to connect.
Figure 6 - 16
Bluetooth Settings
6 - 20 Bluetooth & WLAN Combo Module
Modules & Options
Intel
®
Rapid Storage Technology
Install the Intel® Rapid Storage Technology to support your AHCI mode SATA drive.
IRST Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc into an attached
DVD drive.
2. Click Option Drivers (button).
3. Click 3.Install IRST Driver > Yes.
4. Click Next.
5. Click in the check box to accept the license and click Next.
6. Click Next > Next > Next.
7. Click Finish to restart the computer.
8. Run the
Intel® Rapid Storage Technology app from the Apps screen.
IRST and M.2 PCI-e
SSDs
Note that Intel® Rapid
Storage Technology
does not support M.2
SSDs with a PCI-e In-
terface (M.2 SSDs with a SATA Interface are supported).
6
Intel® Rapid Storage Technology 6 - 21
6
Modules & Options
Trusted Platform Module
(Optional)
The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features.
Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. In addition Make sure you prepare
a removable media (e.g. a USB flash drive) to store passwords etc. before begin-
ning the TPM initialization process.
Before setting up the TPM functions you must enable and initialize the security platform.
6 - 22 Trusted Platform Module
Enabling & Activating TPM
1.
Restart the computer.
2.
Enter the Aptio Setup Utility pressing F2 during the POST/startup.
3.
Use the arrow keys to select the Security menu.
4.
Select TPM Configuration and press Enter to access the sub-menu.
5.
Press Enter to access the TPM Support menu and select Enable to display the full TPM configuration menu.
6.
Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer.
Modules & Options
6
Figure 6 - 17
TPM State
(Enabled)
7.
As the computer restarts press F2 to enter the BIOS again and go to the TPM
Configuration menu.
Trusted Platform Module 6 - 23
Modules & Options
8.
Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership and press Enter).
You will then need to press F4 to save the changes and restart the computer.
6
Figure 6 - 18
Pending TPM operation
(Enable Take
Ownership)
9.
You can now manage the TPM from Windows.
6 - 24 Trusted Platform Module
TPM Management in Windows
You can manage your TPM settings from within Windows:
1.
Go to the Control Panel.
2.
Click BitLocker Drive Encryption (System and Security).
3.
Click TPM Administration.
Modules & Options
Figure 6 - 19
BitLocker Drive
Encryption
(TPM
Administration)
6
Trusted Platform Module 6 - 25
Modules & Options
4.
The TPM Management window allows you to configure the TPM within Windows.
As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here.
6
Figure 6 - 20
Trusted Platform
Module (TPM)
Management on
Local Computer
Administration
6 - 26 Trusted Platform Module
TPM Actions
1.
Click Prepare the TPM and follow the instructions in the Wizard to prepare the
TPM (this will probably require a restart of the computer and confirmation of the setting changes after restart by pressing the appropriate F key).
2.
After the restart the TPM will be prepared and you can then use the Actions menu to Turn TPM off, Change Owner Password, Clear TPM or Reset TPM Lockout.
3.
A wizard will help take you through any setup steps.
Modules & Options
Figure 6 - 21
TPM Actions Menu
6
Trusted Platform Module 6 - 27
6
Modules & Options
BitLocker
BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk. Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
1.
Click Turn on Bit Locker.
2.
Follow the on-screen instructions to setup BitLocker, and make sure you have a removable media (e.g. a USB flash drive) to store saved recovery keys etc.
Figure 6 - 22
BitLocker Drive
Encryption
6 - 28 Trusted Platform Module
Modules & Options
3G/4G Module
If you have included an optional UMTS/HSPA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module or LTE
(Long Term Evolution) 4G module (see
for specification details) in your purchase option, you do not require a driver/application
installation for Windows 8.1. Follow the instructions overleaf to install the USIM card (which will be provided by your service provider), and then use the Charms
Bar Wireless icon to access the 3G/4G network in the same manner as the WLAN
).
Important Notice
If your purchase option includes both Wireless LAN and 3G/4G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Important Notice - 3G/4G & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3G/4G module and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G/4G module is powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN,
Bluetooth and 3G/4G
module(s) are OFF (or the system is in Air-
plane Mode) if you are using the computer aboard aircraft (see
6
3G/4G Module 6 - 29
6
Modules & Options
Power Safety
Warning
Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
USIM Card Orientation
Note that the USIM card’s readable side (with the gold-colored contacts) should face upwards as illustrated.
3G/4G Module USIM Card Installation
Follow the instructions below to install the USIM card (which will be provided by your service provider).
1.
Turn the computer off, and turn it over.
2.
Slide the latch
1
in the direction of the arrow.
3.
Slide the latch
2
in the direction of the arrow, and hold it in place.
4.
Slide the battery out in the direction of the arrow
3
.
5.
Insert the USIM card
4
as illustrated below until it clicks fully into position, and replace the battery.
1 2
3
4 5
Figure 6 - 23
Battery Removal &
USIM Card Insertion
6 - 30 3G/4G Module
Modules & Options
3G/4G Configuration in Windows
You can configure a 3G/4G connection as below, however make sure the system is not in Airplane Mode before configuration begins.
Charms Bar
1.
Go to the Charms Bar.
2.
Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
3.
A list of available access points will appear under Mobile Broadband.
3G/4G Module PIN
Code & Power-Saving
Note that there may be some issues when a/4G
PIN Code is set for 3G modules in Windows, if
Mobile Broadband has been turned off, and the system has resumed from a power-saving state. See “
6
Figure 6 - 24
Networks
Mobile Broadband
3G/4G Module 6 - 31
Modules & Options
4.
Any 3G/4G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband.
5.
Double-click any connection icon under Mobile Broadband (or click and then click
Connect).
6
Figure 6 - 25
Mobile Broadband
(Connect)
6 - 32 3G/4G Module
6.
The system will connect to your network.
7.
A Connected will appear alongside the 3G/4G connection (click the connection to view the timer which indicates your connected time for the current session).
8.
You can then access the internet, download e-mail etc. as per any internet connection.
9.
To disconnect you can select the connection and click Disconnect .
Modules & Options
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the system is in Airplane Mode if you are using the computer aboard aircraft.
6
10. You need to either use Airplane Mode, or to turn the Mobile Broadband module
off aboard aircraft.
Figure 6 - 26
Mobile Broadband
(Disconnect)
3G/4G Module 6 - 33
6
Modules & Options
Compatible
Adapters
For a list of compatible adapters check the video adapter/display device documentation, or with your distributor/ supplier.
Wireless Display
Wireless Display uses your Wireless LAN module/WLAN Bluetooth Combo module (you need to make sure that your video adapter/display device is compatible
with your particular WLAN/Combo module) in conjunction with a compatible
video adapter/display device (purchased separately) to allow you to display the contents of the notebook display on another display (e.g. HDTV), without the need to have cables stretching across a room.
You can use the wireless display to play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables.
Before configuring Wireless Display you will need to set up your compatible
adapter with your display/speakers. Connect the adapter using an HDMI or A/V cable and turn on the display (or in the case of speakers connect them to the wireless speaker adapter with the cables provided with the adapter), and then set the display to the appropriate input channel (see the documentation supplied with your compat-
ible adapter/display for full details).
Note that no driver or application is required for wireless display in Windows 8.1.
6 - 34 Wireless Display
Wireless Display Configuration
1.
Note that no driver or application is required for wireless display in Windows 8.1.
2.
Go the Charms Bar, select Devices.
3.
Click Project.
4.
Click Add a wireless display.
Modules & Options
Figure 6 - 27
Add a Wireless
Display
6
Wireless Display 6 - 35
6
Modules & Options
5.
The system will then search for compatible display devices (this may take up to
60 seconds so allow time for this to complete).
Figure 6 - 28
Searching For
Devices
Figure 6 - 29
Enter PIN
6.
Double-click any detected display device in the list.
7.
You may then need to input a pin number for the device to which you are connecting.
8.
Click Next.
6 - 36 Wireless Display
9.
The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details).
10. To disconnect from the display you can select it in PC and Devices > Devices and click Remove Device > Yes; or go to the Project menu (Charms Bar > Devices) and click Disconnect.
Modules & Options
Figure 6 - 30
Remove Device/
Disconnect
6
Wireless Display 6 - 37
6
Modules & Options
6 - 38
Troubleshooting
Chapter 7: Troubleshooting
Overview
Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried.
Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative.
7
Overview 7 - 1
7
Troubleshooting
Basic Hints and Tips
Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working.
• Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip,
make sure it is actually working. Check the LED Power & Communication Indicators (see
) to see the computer’s power status.
• Connections - Check all the cables to make sure that there are no loose connections anywhere.
• Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config-
ured in your Power Options (see
“Power-Saving States” on page 3 - 7
), the Fn + F4 key combination, or
power button to wake-up the system.
• Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the brightness.
• Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.
• Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive.
7 - 2 Basic Hints and Tips
Troubleshooting
Backup and General Maintenance
• Always backup your important data, and keep copies of your OS and programs safe, but close to hand.
Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet.
• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so.
• Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Supervisor password for the BIOS (see
“The Setup Utility” on page 5 - 2
• Keep copies of vital settings files such as network, dialup settings, mail settings etc.(even if just brief notes).
Warranty
The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.
7
Backup and General Maintenance 7 - 3
7
Troubleshooting
Viruses
• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini-
tions file updates are usually downloadable directly from the internet.
• Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e-
mail attachments so take care when opening any attached file. You can configure most Anti-Virus programs to check all e-mail attachments. Note: You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the person’s knowledge.
• Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OS’s documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one).
7 - 4 Viruses
Troubleshooting
Upgrading and Adding New Hardware/Software
• Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system.
• Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
• Read the documentation. We can assume, since you are reading this that you are looking at the computer’s manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”.
• When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected.
• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendor’s websites).
7
Upgrading and Adding New Hardware/Software 7 - 5
7
Troubleshooting
• Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs.
• Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming.
7 - 6 Upgrading and Adding New Hardware/Software
Troubleshooting
Problems and Possible Solutions
Problem Possible Cause - Solution
You turned on the power but it doesn’t work.
Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
blinking orange.
immediately, turn it off then on again.
You are losing battery power too quickly.
The system is using too much power. If your OS has a Power Options scheme
(see
“Shutting the Computer Down” on page 3 - 4
may also be using a peripheral device/USB device that is drawing a lot of power.
Actual battery operating time is shorter than expected.
The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see pages
Power Options have been disabled. Go to the Control Panel in Windows and re-enable the options.
A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power.
7
Problems and Possible Solutions 7 - 7
7
Troubleshooting
Problem
The computer feels too hot.
Possible Cause - Solution
Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see
). Make sure you’re using the correct adapter.
Nothing appears on screen.
No image appears on the external
monitor I have plugged in and powered on.
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan intakes to be blocked.
The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see
“Configuring the Power Buttons” on page 3 - 9
The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If an external monitor is connected, turn it on.
The screen saver is activated. Press any key or touch the TouchPad.
You haven’t installed the video driver and configured it appropriately from the
for instructions on installing and configuring
the video driver.
7 - 8 Problems and Possible Solutions
Problem
You forget the boot password.
Troubleshooting
Possible Cause - Solution
If you forget the password, you may have to discharge the battery of the CMOS.
Contact your service representative for help.
Password Warning
If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
The sound cannot be heard or the volume
is very low.
The volume might be set too low. Check the volume control in the Volume
Control Panel in the Windows notification area, or use the key combination Fn
“Function/Hot Key Indicators” on page 1 - 10
) to adjust.
“Function/Hot Key Indicators” on page 1 - 10
).
Unwelcome numbers appear when typing.
I am sliding my finger up and down on the right side of the Touchpad to scroll a
Window and the Touchpad does not
respond.
There are different Touchpad versions available on this computer, and this
version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
7
Problems and Possible Solutions 7 - 9
Troubleshooting
Problem Possible Cause - Solution
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
7
The system freezes or the screen goes dark.
The system never goes into a power
saving mode.
The Wireless LAN/Bluetooth modules cannot be detected.
The PC Camera module cannot be detected.
The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit.
Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see
“Power-Saving States” on page 3 - 7
). Make sure you have enabled Hibernate mode from the control panel.
The modules are off as the computer is in Airplane Mode. Check the LED indicator to see if it is in Airplane Mode (see
). Use the Fn + F11 key combination to toggle Airplane
Mode on/off (see
The module is off. Press the Fn + F10 key combination in order to enable the module (see
“Function/Hot Key Indicators” on page 1 - 10
). Run the camera application to view the camera picture.
7 - 10 Problems and Possible Solutions
Troubleshooting
Problem
The Wireless LAN/Bluetooth modules cannot be configured.
A file cannot be copied to/from a connected Bluetooth device.
I cannot obtain high speed Bluetooth data transfer.
Possible Cause - Solution
The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in
“Modules & Options” on page 6 - 1
).
The transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not
supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process has been completed
To obtain high speed Bluetooth data transfer take into account the following:
• To achieve high speed transfer speeds, both devices must support high
speed data transfer (i.e both the computer and the Bluetooth compatible device you are connecting to).
• Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer, and for configuration information.
7
Problems and Possible Solutions 7 - 11
7
Troubleshooting
Problem Possible Cause - Solution
I have used Update Driver in Device
Manager (Unknown device > Other
Devices) to try and install the Airplane
Mode driver. Windows encountered a problem in attempting to update the driver, and a yellow exclamation mark appears in Device Manager against the Unknown
device.
It is very important that the drivers are installed in the order indicated in Chapter
4 (which is the numbered installation order on the Device Drivers & Utilities +
User’s Manual disc). This issue can occur when drivers are manually installed, and not in the correct order.
If you have attempted to Update Driver from the Device Manager control panel and have encountered problems, then use the method below to correct this:
To correct this problem:
1.
Go to the Programs and Features (Programs) control panel in
Windows.
2.
Select any installed Airplane Mode driver item (e.g. Insyde Airplane
Mode HID Mini-Driver), and click Uninstall/Change to uninstall the current driver.
3.
Restart the computer.
4.
Insert the Device Drivers & Utilities + User’s Manual disc and click
Install Drivers (button).
5.
Double-click the Airplane Driver item in the menu.
6.
Follow the instructions to install the correct driver (you will need to restart the computer as part of the installation process).
7 - 12 Problems and Possible Solutions
Troubleshooting
Problem
I have connected a Bluetooth Mouse but it loses the Bluetooth connection and no longer responds after a short period of inactivity.
Possible Cause - Solution
This is an issue with some mouse models and the Intel Wireless 7260 WLAN
and Bluetooth combo module series. To resolve this issue do the following:
1.
Go to the Device Manager control panel in Windows.
2.
Click the arrow alongside Bluetooth to expand the menu if required.
3.
Double-click Intel(R) Wireless Bluetooth(R) 4.0 + HS Adapter.
4.
Click the Power Management tab.
5.
Make sure that the check box alongside “allow the computer to turn
off this device to save power” doesn’t have a check alongside it.
6.
Click OK and close the control panel.
7
Figure 7 - 1
- Device Manager (Bluetooth)
Problems and Possible Solutions 7 - 13
7
Troubleshooting
Problem
When using a Bluetooth headset the
audio appears to be mono and not stereo.
Possible Cause - Solution
This is a common issue with Bluetooth headsets. To resolve this issue do the following (you will need to repeat this procedure after every boot up, restart, or when the system resumes from hibernation):
1.
Go to the Devices & Printers control panel in Windows.
2.
Double-click the Bluetooth headset.
3.
Click Connect to complete the stereo connection.
OR
1.
Go to the Sound control panel in Windows.
2.
Right-click (in the Playback tab) the Bluetooth Stereo Audio device
(the default device is Headset).
3.
Click Connect to complete the stereo connection.
7 - 14 Problems and Possible Solutions
Troubleshooting
3G/4G Module PIN Code & Power-Saving
Note that there may be some issues when a PIN Code is set for the 3G/4G module in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is
recommended that you simply do not enable a PIN for the 3G/4G module. The following provides instructions for disabling the PIN code.
Disabling a PIN code for a 3G/4G Module
1.
Go to the Charms Bar.
2.
Click Change PC Settings.
7
Figure 7 - 2
- Change PC Settings
3G/4G Module PIN Code & Power-Saving 7 - 15
7
Troubleshooting
3.
Click Network.
4.
Click the broadband connection under Mobile Broadband.
5.
Scroll down to Security and click Remove PIN.
6.
Enter the current PIN number and click OK.
7.
It is recommended that you do not Enable a PIN for the 3G/4G module.
Figure 7 - 3
- Disable PIN
7 - 16 3G/4G Module PIN Code & Power-Saving
Troubleshooting
Resolving the “Insert a SIM” issue with the 3G/4G Module (Windows 8.1)
1.
If a PIN was set for the 3G/4G module, you have then switched Mobile broadband off (or put the system in
Airplane Mode) in Networks, and the system has just resumed from a power-saving state the following error may occur.
2.
On resuming from the power-saving state the standard procedure would be to go to Networks in the Charms
Bar and turn on Mobile broadband.
3.
Go to the Charms Bar.
4.
Select Settings and you will then note that the WiFi icon will read Unavailable.
5.
Standard procedure would be to click the connection and enter the PIN number to unlock the connection.
6.
In this instance you will note that the Mobile broadband connection will read Insert a SIM.
7.
In this case you will need to restart the computer.
8.
After system restart you can then connect to the Mobile Broadband as normal.
9.
To fully resolve this issue it is recommended that you do not Enable a PIN for the 3G/4G module.
7
3G/4G Module PIN Code & Power-Saving 7 - 17
7
Troubleshooting
7 - 18
Interface (Ports & Jacks)
Appendix A: Interface (Ports & Jacks)
Overview
The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
A
Interface (Ports & Jacks) A - 1
Interface (Ports & Jacks)
Notebook Ports and Jacks
Item
Card Reader
DC-In Jack
Description
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
Plug the supplied AC/DC adapter into this jack to power your computer.
External Monitor (VGA)
Port
This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
A
HDMI-Out Port
Headphone-Out Jack
The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or
Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries
both audio and video signals.
Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack.
A - 2 Interface (Ports & Jacks)
Interface (Ports & Jacks)
Item
Microphone-In Jack
Description
Plug an external microphone in to this jack to record on your computer.
RJ-45 LAN Jack This port supports LAN (Network) functions.
Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Security Lock Slot
USB 2.0/1.1 Port
USB 3.0 Port
3.
0
To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
The USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your
USB device is 500mA or above, make sure you use the power supply which comes with the device).
The USB 3.0 port is denoted by its blue color
; and the USB 2.0 ports are colored black. USB
3.0 will transfer data much faster than USB 2.0, and is backwards-compatible with USB 2.0.
A
Interface (Ports & Jacks) A - 3
Interface (Ports & Jacks)
A
A - 4
Control Center
Appendix B: Control Center
Overview
The following chapter will give a quick description of the functions of the Control Center.
The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the dial control where applicable. Certain functions will automatically be adjusted when a power mode is selected. The Control Center in Windows 8.1 works under the Desktop App and not under the Start screen.
Control Center Access
To run the Control Center press the Fn + Esc key combination or double-click the icon in the notification area of the taskbar.
Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).
B
Figure B - 1 - Control Center
Control Center B - 1
B
Control Center
Power Modes
You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect the Power Conservation Mode, Airplane Mode, Power Plan and PC camera power etc.
You can click a Control Center icon to set an overall power mode and then click individual icons in the
Control Center to power on/off the Touchpad and PC camera.
Modes Quiet Power Saving Performance Entertainment
Icon
Power Plan
Power Conservation Mode
PC Camera
Balanced
Balance
ON
Power Saver
Energy Star
High Performance
Performance
OFF ON
Balanced
Balance
ON
TouchPad ON ON ON ON
Airplane Mode OFF ON
Table B - 1- Power Modes
OFF OFF
B - 2 Control Center
Control Center
Control Center Menus
The Control Center contains 2 menu headings (System Program & Device) under the Power Modes. Click the menu headings and then click any of the buttons outlined on the following pages.
Figure B - 2 - Control Center Menus
Control Center B - 3
B
B
Control Center
Power Status (System Program)
/
The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state.
Brightness (System Program)
The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight
(press any key to turn it on again).
Volume (System Program)
The Volume icon will show the current volume level. You can use the slider to adjust the Volume or the Fn +
F5/F6 key combinations, or use the Fn+ F3 key combination to mute the volume.
Fan Speed (System Program)
You can set the fan speed to Maximum (full power) or Automatic from this menu item. The fan speed will adjust itself automatically to control the heat of the CPU. However you can adjust the setting to maximum if you prefer.
Power Conservation (System Program)
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into
a low-power sleep modes after a designated period of inactivity (see
“Power Conservation Modes” on page 3 -
). Click either the Performance, Balanced or Energy Star button.
B - 4 Control Center
Control Center
Sleep Button (System Program)
Click either the Hibernate or Sleep buttons to have the computer enter the selected power-saving mode when
the Fn + F4 key combination is pressed (see
“Power-Saving States” on page 3 - 7
Display Switch (System Program)
Click the Display Switch button to access the menu (or use the + P key combination) and select the appropriate attached display mode.
Time Zone (System Program)
Clicking the Time Zone button will access the Date and Time Windows control panel.
Desktop Background (System Program)
Clicking the Desktop Background button will allow you to change the desktop background picture.
TouchPad/PC Camera (Device)
Click either of these buttons to toggle the TouchPad or camera module’s power status. The icon will appear dimmed when it is disabled
.
Note that the power status of the camera module is also effected by the Power Mode selected (see
Table B - 1, on page B - 2
).
Caps Lock/Scroll Lock/ Number Lock/Airplane Mode
Click the button to toggle the appropriate lock mode and Airplane Mode.
B
Control Center B - 5
Control Center
B
B - 6
Intel Video Driver Controls
Appendix C: Intel Video Driver Controls
The basic settings for configuring the LCD are outlined in
“Video Features” on page 1 - 25
.
Intel Video Driver Installation
Make sure you install the drivers in the order indicated in
1.
Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Dynamic Video Memory Technology
Intel
®
DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver
must be installed). DVMT returns whatever memory is no longer needed to the operating system.
C
Intel Video Driver Installation C - 1
Intel Video Driver Controls
Intel
®
HD Graphics Control Panel
Advanced video configuration options are provided by the Intel
®
HD Control Pan-
el. To access the control panel see below and overleaf:
1.
Click the Intel® HD Graphics Control Panel icon in the Apps screen.
C
Figure C - 1
Apps Screen
Intel® HD Graphics
Control Panel
(see over)
C - 2 Intel® HD Graphics Control Panel
Intel Video Driver Controls
OR
2.
Right-click the Desktop and select Graphics Properties from the menu.
OR
3.
Click Advanced settings in the Screen Resolution control panel in Windows.
4.
Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties
(button).
5.
Double-click the Intel(R) HD Graphics control panel in the Windows Control
Panel.
Figure C - 2
Intel® HD Graphics
Control Panel
C
Intel® HD Graphics Control Panel C - 3
Intel Video Driver Controls
You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings from the menus.
C
Figure C - 3
Intel® HD Graphics
Control Panel
C - 4 Intel® HD Graphics Control Panel
Intel Video Driver Controls
Sub-Menus
Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Figure C - 4
Intel® HD Graphics
Control Panel
Sub-Menus
Intel® HD Graphics Control Panel C - 5
C
C
Intel Video Driver Controls
Multiple Display
At least one other display must be attached in order to view multiple display selection options.
Display
Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays.
Figure C - 5
Intel® HD Graphics
Control Panel
Display Settings
C - 6 Intel® HD Graphics Control Panel
Intel Video Driver Controls
Click the Display menu at the top of the screen to display the sub-menus. The Mul-
tiple Displays menu allows you to configure the display mode of any attached displays (see
“Attaching Other Displays” on page C - 15
Multiple Display
At least one other display must be attached in order to view multiple display selection options.
Figure C - 6
Intel® HD Graphics
Control Panel
Display Settings -
Multiple Displays
C
Intel® HD Graphics Control Panel C - 7
Intel Video Driver Controls
The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio
Without Video to keep audio on when the display blanks out for power saving purposes.
Figure C - 7
Intel® HD Graphics
Control Panel
Display Settings -
Audio
C
C - 8 Intel® HD Graphics Control Panel
Intel Video Driver Controls
3D
This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and
Custom Settings allows you to configure the Anti-Aliasing, Anisotropic Filtering and Vertical Sync features to your preferences. Click Apply to save changes.
Figure C - 8
Intel® HD Graphics
Control Panel 3D
C
Intel® HD Graphics Control Panel C - 9
C
Intel Video Driver Controls
Options and Support
Options and Support allows you to Customize Hot Keys (for opening the application, rotating the display, scaling) to your preferences. Click Apply to save changes.
Figure C - 9
Intel® HD Graphics
Control Panel
Options and
Support
C - 10 Intel® HD Graphics Control Panel
Intel Video Driver Controls
Click the Options and Support menu at the top of the screen to display the submenus. The Information Center provides details on System Information, the
Built-In Display and any attached displays.
Preferences
Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics
Control Panel.
Make sure you turn Tray
Icon On to display the Intel® HD Graphics Control
Panel icon in the notification area of the taskbar (as below).
Figure C - 10
Intel® HD Graphics
Control Panel
Options & Support-
Information Center
Intel® HD Graphics Control Panel C - 11
C
C
Intel Video Driver Controls
Video
The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time.
Click Apply to save changes (select Color Enhancement, Image Enhancement,
Image Scaling or Gamut Mapping from the menu).
Figure C - 11
Intel® HD Graphics
Control Panel -
Video (Color
Enhancement)
C - 12 Intel® HD Graphics Control Panel
Intel Video Driver Controls
The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Figure C - 12
Intel® HD Graphics
Control Panel Video
Image Scaling &
Gamut Mapping
Intel® HD Graphics Control Panel C - 13
C
Intel Video Driver Controls
Display Devices & Options
Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported.
Attaching Displays
When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R)
HD Graphics Control Panel to configure the full screen display.
C
Table C - 1
Display Modes
Display Mode
Single Display
Clone/Duplicate
Extended Desktop /
Extend
Collage
C - 14 Display Devices & Options
Description
One of the connected displays is used as the display device
(PC screen only or Second screen only).
Both connected displays output the same view and may be configured independently
Both connected displays are treated as separate devices, and act as a virtual desktop
A number of connected displays are combined into a single unified higher resolution for larger screen sizes
Intel Video Driver Controls
Attaching Other Displays
To Clone Displays:
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3.
Click Clone from the Select Multiple Display Mode menu.
4.
Click Apply, and OK to confirm the settings change.
5.
You can select the displays to be used from the Select Active Displays menu.
Multiple Display
At least one other display must be attached in order to view Multiple
Display selection options.
Figure C - 13
Display > Multiple
Displays (Clone)
C
Attaching Other Displays C - 15
C
Intel Video Driver Controls
Display Settings
Extended Desktop
You can have different
Colors, Screen Area and Monitor Refresh
Rates for each display device provided your
monitor can support
them.
You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays.
To Enable Extended Mode:
1.
Attach your external display to the HDMI-Out port/external monitor port, and turn it on.
2.
Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3.
Click Extended from the Select Multiple Display Mode menu.
4.
Click Apply, and OK to confirm the settings change.
Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display).
Figure C - 14
Display > Multiple
Displays (Extended)
Click Display Set-
tings to make any adjustments required.
C - 16 Attaching Other Displays
Intel Video Driver Controls
To Enable Collage Mode:
1.
Attach your external displays to the external monitor port and HDMI-Out port, and turn them on.
2.
Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3.
Click Collage from the Select Multiple Display Mode menu.
4.
Click Enable.
5.
Click Vertical or Horizontal to arrange and displays as required.
6.
Click Apply, and OK to confirm the settings change.
Collage Mode
Collage mode is used to combine a number of displays into a single unified higher resolution for larger screen sizes,.
Figure C - 15
Display > Multiple
Displays (Collage)
C
Attaching Other Displays C - 17
C
Intel Video Driver Controls
Windows Logo Key
+ P Key
Combination
You can use the
+ P
key combination to quickly bring up the Sec-
ond Screen menu.
You can also use the
Display Switch button in the Control Center to access the menu and select the appropriate attached display mode.
You can also use the Fn
+F7 key combination to quickly access the Sec-
ond Screen menu in
Windows.
Attaching Other Displays - Devices (Charms Bar)
You can configure attached displays from Devices (in the Charms Bar)
.
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go the Charms Bar, select Devices.
3.
Click Project (you may need to click Second Screen).
4.
Click on any one of the options from the menu to select PC screen only,
Duplicate, Extend or Second screen only.
Figure C - 16
Second Screen
(Devices)
C - 18 Attaching Other Displays - Devices (Charms Bar)
Intel Video Driver Controls
Configuring an External Display In Windows
1.
Attach your external display to the external monitor port/HDMI-Out port, and turn it on.
2.
Go to the Screen resolution control panel (see page
1 - 30
) in the Desktop app.
3.
Click the Detect button.
4.
The computer will then detect any attached displays.
Figure C - 17
Screen Resolution
Multiple Displays
C
Attaching Other Displays - Devices (Charms Bar) C - 19
Intel Video Driver Controls
5.
You can configure the displays from the Multiple Displays menu.
Figure C - 18
Screen Resolution
Multiple Display
Options
C
• Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s)
• Extend these displays - Treats both connected displays as separate devices
• Show desktop only on 1/2 - Only one of your displays is used.
C - 20 Attaching Other Displays - Devices (Charms Bar)
Intel Video Driver Controls
HDMI Audio Configuration
HDMI (High-Definition Multimedia Interface) carries both audio and video signals.
In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below.
1.
Go to the Control Panel.
2.
Click Sound (Hardware and Sound) and click Playback (tab)
3.
Depending on your display, the playback device may be selected, however in some cases you may need to select the audio device and click Set Default (button).
4.
Double-click the device to access the control panel tabs illustrated overleaf.
Volume Adjustment
The sound volume level can be set using the volume control in the Set-
tings
menu in the
Charms Bar.
Figure C - 19
Sound - HDMI
Device (set Default)
HDMI Audio Configuration C - 21
C
Intel Video Driver Controls
5.
Adjust the HDMI settings from the control panel tabs.
6.
Click OK to close the Sound panel.
C
Figure C - 20
HDMI Device
Properties
C - 22 HDMI Audio Configuration
Intel Video Driver Controls
HDMI Notes
• Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
• To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual).
HDMI Video Configuration
1.
Connect an HDMI cable from the HDMI-Out port to your external display.
2.
Configure your external display as per the instructions in
3.
Set up your external display (TV or LCD) for HDMI input (see your display device manual).
4.
You can now play video/audio sources through your external display.
Other Applications
If you are using a third party application to play
DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation).
C
HDMI Audio Configuration C - 23
Intel Video Driver Controls
C
C - 24
Specifications
Appendix D: Specifications
Latest Specification Information
The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications D - 1
D
D
Specifications
Processors
Intel® Core i7-4510U (2.00GHz)
4M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 15W
Intel® Core i5-4210U (1.70GHz)
3M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 15W
Intel® Core i3-4025U (1.90GHz)
3M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 15W\
Intel® Pentium® 3558U (1.70GHz)
2M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 15W
Intel® Celeron® 2957U (1.40GHz)
2M L3 Cache, 22nm (22 Nanometer),
DDR3L-1600MHz, TDP 15W
Display
13.3” / 33.78cm QHD+ (3200 * 1800),
WQHD (2560 * 1440), FHD (1920 *
1080), HD+ (1366 * 768),
2.85mm Thick 16:9 Backlit Panel
Memory
Dual Channel DDR3L
Two 204 Pin SO-DIMM Sockets
Supporting DDR3L 1600 MHz Memory
Modules (real operational frequency
depends on the FSB of the processor)
Memory Expandable up to 16GB
Compatible with 2GB, 4GB or 8GB Modules
Video Adapter
Intel® HD Graphics 4400 (Integrated with i7-4510U, i5-4210U& i3-4025U CPUs)
Dynamic Frequency
Intel Dynamic Video Memory Technology up to 1.7GB
Microsoft DirectX®11.1 Compatible
Intel® HD Graphics (Integrated with
Pentium® 3558U & Celeron®
2957UCPUs):
Dynamic Frequency
Intel Dynamic Video Memory Technology up to 1.7GB
Microsoft DirectX®11.1 Compatible
Storage
One Changeable 2.5" / 7.0 mm (h) HDD/
SSD with SATA (Serial) Interface
One M.2 SSD with SATA (Serial)
Interface (Factory Option)
Audio
High Definition Audio Interface
Built-In Microphone
2 * Built-In Speakers
Pointing Device & Keyboard
Built-in TouchPad with Multi-Gesture and
Scrolling Functionality
A4 Size Isolated Keyboard
Interface
Two USB 2.0 Ports
One USB 3.0 Port
One External Monitor Port
One HDMI-Out (High-Definition
Multimedia Interface) Port (with HDCP)
One Headphone-Out Jack
One Microphone-In Jack
D - 2 Specifications
Specifications
One RJ-45 LAN Jack
One DC-In Jack
Card Reader
Embedded Multi-In-1 Card Reader
- MMC/ RS MMC
- SD/ Mini SD / SDHC/ SDXC
Note: Some of these cards require PC adapters that are usually supplied with the cards.
Slot
Three M.2 Slots:
=======================================
For i7-4510U, i5-4210U CPUs:
Slot 1: for M.2 WLAN Combo Module with
PCIe & USB Interfaces
Slot 2: for M.2 SSD with SATA / PCI-e
Interface
Slot 3: for M.2 3G Module (UTMS/
HSPA+) with USB Interface OR M.2 LTE
4G Module with USB Interface
===============================
===============================
For i3-4025U, i5-4210U Pentium®
3558U & Celeron® 2957UCPUs:
Slot 1: for M.2 WLAN Combo Module with
PCIe & USB Interfaces
Slot 2: for M.2 SSD with SATA Interface
Slot 3: for M.2 3G Module (UTMS/
HSPA+) with USB Interface OR M.2 LTE
Module with USB Interface
===============================
Communication
Built-In 10/100/1000Mb Base-TX
Ethernet LAN
Intel® Dual Band Wireless-AC 7265
(2*2 802.11 a/c) M.2 WLAN
+
Bluetooth
Combo Module (Factory Option)
Intel® Dual Band Wireless-AC 3160
(1*1 802.11 a/c) M.2 WLAN
+
Bluetooth
Combo Module (Factory Option)
3rd Party M.2 Combo WLAN (802.11b/g/ n) and Bluetooth v4.0+LE Module
(Factory Option)
3G UTMS/HSPA+ M.2 Module (Factory
Option)
M.2 LTE 4G Module with USB Interface
(Factory Option)
1.0M HD Video Camera Module with
USB interface (Factory Option)
Power Management
Supports Wake on LAN
Supports Wake on USB
Supports Wake on RTC Alarm (AC Mode
Only)
Power
Full Range AC/DC Adapter
AC input 100 - 240V, 50 - 60Hz,
DC Output 19V, 2.1A (40 Watts)
Removable 3 Cell Smart Lithium Ion
Battery Pack 24WH
Removable 3 Cell Smart Lithium Ion
Battery Pack 31WH (Factory Option)
D
Specifications D - 3
D
Specifications
Security
Security (Kensington® Type) Lock Slot
BIOS Password
Trusted Platform Module 1.2 (Factory
Option)
Features
Painted Style
Intel® Rapid Start Technology
Intel® Smart Connect Technology
Shipping Mode
Operating System
Windows® 8.1 (64-bit)
Windows® 7 (64-bit)
Indicators
LED Indicators - Power/Suspend, Battery,
HDD/ODD, Airplane Mode, Camera
BIOS
One 48Mb SPI Flash ROM
AMI BIOS
Environmental Spec
Temperature
Operating: 5
°
C - 35
°
C
Relative Humidity
Operating:
Non-Operating:
20% - 80%
10% - 90%
Dimensions & Weight
326mm(w) * 231mm(d) * 23.6mm(h)
(Height excluding battery area)
1.4 kg *Barebone System with 24WH
Battery & ODD
A barebone system does not include the HDD,
RAM, adapter, power cord, VGA card and factory option modules (weight tolerance within +/- 5%).
D - 4 Specifications
Windows 7
Appendix E: Windows 7
Overview
This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows 7 OS.
You can refer to the main manual for details of drivers required, audio & video information, BIOS, modules etc.
However any information specific to Windows 7 will be included in this Appendix, as well as details on how to navigate the Windows 7 user interface to access the applications, control panels, taskbar etc.
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 (64-bit with Service Pack
1 installed) operating system is supported.
Windows Versions
Note that the information included on the following pages is for Windows 7 (64-bit) only.
Windows OS
In order to run Windows 7 (64-bit with Service Pack 1) your computer requires a minimum 2GB of system memory
(RAM).
Overview E - 1
Windows 7
Function/Hot Key Indicators (Windows 7)
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
Keys
Fn +
Fn +
Fn +
Function
Play/Pause (in Audio/Video Programs)
Touchpad Toggle
(Disable toggle by using the Touchpad
Turn LCD Backlight Off
(Press a key to or use TouchPad to turn on)
Fn +
Keys
Fn +
Fn +
Brightness
Decrease/
Increase
PC Camera
Power Toggle
Function
Fn +
Fn +
Fn +
Fn +
Mute Toggle
Volume Decrease/
Increase
Sleep Toggle
Display Switch Menu
Table E - 1 - Function & Hot Key Indicators
Fn + NumLk
Fn + ScrLk
Caps Lock
Fn +
Airplane
Mode Toggle
Number Lock
Toggle
Scroll Lock
Toggle
Caps Lock
Toggle
Fan Control
Toggle -
Maximum /
Automatic
E - 2 Overview
Windows 7
Control Center
Press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/touch pad on/off (see
Appendix B
for full details).
Control Center Access
To run the
Control Center press the
Fn + Esc
key combination, or double-click the icon in the notification area of the taskbar.
Close the Control Center by clicking the
close icon in the top right of the panel
(move the cursor onto the top right corner of the panel to highlight it).
Figure E - 1 - Control Center
Overview E - 3
Windows 7
Windows 7 Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties to customize the appearance of the Start menu.
Click here to toggle Category View
Figure E - 2 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.
E - 4 Windows 7 Start Menu & Control Panel
Windows 7
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows 7. For more detailed video information see
“Video Driver Controls” on page C - 1
. To access Display (Control Panel) and Screen Resolution in Windows:
1.
Click Start and click Control Panel.
2.
Click Display (Appearances and Personalization category) and click Adjust resolution.
3.
Use the drop box to select the screen Resolution
1
).
4.
Click OK to confirm setting changes.
5.
Click Advanced settings
2
) to bring up the Advanced properties tabs.
1
Right-Click Desktop
App
You can also right-click the desktop and select
Screen resolution 3
to quickly access the control panel.
2
3
Figure E - 3 - Screen Resolution
Video Features E - 5
Windows 7
To access the Intel(R) HD Graphics Control Panel:
1.
Click Advanced settings
2
(
) in the Display Settings control panel in Windows.
2.
Click Graphics Properties (button)
4
(
Figure E - 4
) in the Intel(R) HD Graphics Control Panel tab.
OR
3.
Right-click the desktop and select Graphics Properties
5
(
Figure E - 4
) from the menu.
OR
4.
Click the icon
6
(
Figure E - 4
) in the taskbar notification area and select Graphics Properties from the menu.
OR
5.
Access the Intel(R) HD Graphics Control Panel from the Windows control panel in Classic View.
5
6
4
E - 6 Video Features
Figure E - 4 - Intel(R) HD Graphics Control Panel Access
Windows 7
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options. Pay attention to the instructions on battery care in
“Battery Information” on page 3 - 14
Figure E - 5 - Power Options
Power Options E - 7
Windows 7
Driver Installation &
Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a work-
ing power source.
Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems
(note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
Drivers & Utilities (Windows 7)
Make sure you install all the drivers and utilities for your system.
What to Install
The
Device Drivers & Utilities + User’s Manual
disc contains the drivers and utilities necessary for the proper operation of the computer.
lists what you need to install and it is very important that the drivers are installed
in the order indicated.
Note that the information included on the following pages is for Windows 7 only. See
“Drivers & Utilities (Win 8.1)” on page 4 - 1
for information on drivers and utilities for the Windows 8.1 operating system.
E - 8 Drivers & Utilities (Windows 7)
Windows 7
Driver Installation (Win 7)
Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.
1.
Check the driver installation order from
(the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2.
Click to select the driver you wish to install, (you should note down the drivers as you install them).
3.
Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure E - 6 - Drivers Installer Screen 1 (Win 7)
Note: If you need to reinstall any driver, you should uninstall the driver first.
Figure E - 7 - Drivers Installer Screen 2 (Win 7)
Driver Installation (Win 7) E - 9
Windows 7
Win 7 (64-bit) Driver
Page #
Win 7 - Optional Items
Bluetooth & WLAN Combo Module (Windows 7)
Intel Rapid Storage Technology (Windows 7)
Intel® Wireless Display Application (Windows 7)
Page #
Table E - 2 - Driver Installation
All drivers provided are for the Windows 7 (64-bit with Service Pack 1) operating system.
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
E - 10 Driver Installation (Win 7)
Manual Driver Installation
Click Browse CD/DVD (button) in the Drivers Install-
er application and browse to the executable file in the appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See
“Windows Update” on page E -
14
for instructions.
Windows 7
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1.
Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2.
Double-click Device Manager (Hardware and
Sound > Device Manager).
3.
Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4.
Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
Driver Installation (Win 7) E - 11
Windows 7
User Account Control
If a User Account Control prompt appears as part of the driver installation procedure, click Continue/Al-
low, and follow the installation procedure as directed.
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this
driver software anyway” or Install to continue the installation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” during the installation procedure (other than when out-
lined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter (and in Chapter 6 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver.
E - 12 Driver Installation (Win 7)
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button).
Windows 7
LAN
1.
Click 3.Install LAN Driver > Yes.
2. Click Next > Install.
3. Click Finish.
Chipset
1.
Click 1.Install Chipset Driver > Yes.
2. Click Next.
3. Click the Accept button to agree to the license.
4. Click Install.
5. Click Finish to complete the installation.
CardReader
1.
Click 4.Install Cardreader Driver > Yes.
2. Click Finish.
Video (VGA)
1.
Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Touchpad
1.
Click 5.Install Touchpad Driver > Yes.
2. Click Next.
3. Click Finish.
Note: After installing the video driver go to the Dis-
play/Display Settings control panel to adjust the video settings to the highest resolution.
Hot Key
1.
Click 6.Install Hotkey AP > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Driver Installation (Win 7) E - 13
Windows 7
USB 3.0
1.
Click 7.Install USB 3.0 Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
MEI Driver
1.
Click 8.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish to restart the computer.
Audio
1.
Click 9.Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My
Computer), and click Option Drivers (button) to access the optional driver menu.
It is recommended you now also install the Intel Rap-
id Storage Technology driver (see
“Intel Rapid Storage Technology” on page 6 - 50
- required for AHCI mode hard disks).
Windows Update
After installing all the drivers make sure you enable Win-
dows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1.
Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2.
Click Windows Update (System and Security/
Security).
3.
Click Check for updates (button).
4.
The computer will now check for updates (you need to be connected to the internet).
5.
Click Install now (button) to begin checking for the updates.
6.
Click Install updates (button) to install the updates.
E - 14 Driver Installation (Win 7)
Windows Experience Index
After Video (VGA) driver has been installed, and the system restarted, the OS will automatically run the
"Winsat.exe" to rate the performance. If you have restarted the system during this time then follow the instructions below to update the information.
Windows 7
Optional Drivers
See the pages indicated in
for the driver installation procedures for any modules included in your purchase option.
After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi-
ence Index (make sure the AC/DC adapter is plugged in):
1.
Click Start, and click Control Panel.
2. Click Performance Information and Tools
(System and Security > System > Check the
Windows Experience Index).
3. Click “Rate this computer/Refresh Now/Re-
run the assessment”.
4. The computer will take a few minutes to assess the system performance.
5. Close the control panel.
Figure E - 8 - Option Drivers (Win 7)
Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
Optional Drivers E - 15
Windows 7
Latest PC Camera
Driver Information
Check the Device Driv-
ers & Utilities + User’s
Manual disc, and any accompanying insert pages, for the latest updated information on the
PC Camera driver, which may override the information provided here.
PC Camera Module (Windows 7)
Before installing the Windows 7 PC Camera driver, make sure that the optional PC
Camera is on. Use the Fn + F10 key combination (see
“Function/Hot Key Indicators” on page 1 - 10
) or Control Center button to toggle power to the PC Camera
module. Make sure you install the drivers in the order indicated in
When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red
Make sure you access the application via the desktop shortcut.
PC Camera Application and Power-Saving States
If the computer enters Sleep or Hibernate mode while running the camera application, the program will stop running, and will need to be restarted when the system resumes from the power-saving state.
PC Camera Driver Uninstallation
If you need to uninstall the driver, then uninstall the WebCam Installer item from the Pro-
grams and Features control panel in Windows.
E - 16 PC Camera Module (Windows 7)
Windows 7
PC Camera Driver Installation
1.
Make sure the module is powered on, and then insert the Device Drivers &
Utilities + User’s Manual disc into an attached DVD drive.
2. Click Option Drivers (button).
3. Click 1.Install Webcam Driver > Yes.
4. Click Finish to restart the computer.
5. Run the camera application program from the desktop shortcut (if the hardware is turned off use the Fn + F10 key combination to turn it on again).
PC Camera Audio Setup
If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows.
1.
Click Start, and click Control Panel (or point to Settings and click Control Panel).
2.
Click Sound (Hardware and Sound).
3.
Click Recording (tab).
4.
Right-click Microphone and make sure the item is not disabled.
5.
Double-click Microphone (or select Properties from the right-click menu).
6.
Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required.
7.
Click OK and close the control panels.
8.
Run the camera application program from the desktop shortcut.
9.
Go to the Devices menu heading and select Digital Mic (Realtek High Definition
Audio) (it should have a check alongside it).
10. Go to the Capture menu heading and select Capture Audio (it should have a check alongside it).
PC Camera Screen
Refresh
The PC Camera module supports a frame rate of
12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the
window size, or adjust the Output Size and/or
Color Space Compres-
sion.
To reduce Output Size and/or Color Space
Compression run the camera application, click Options and select
Video Capture Pin. Adjust the settings from the appropriate pull-down menu.
PC Camera Module (Windows 7) E - 17
Windows 7
Right-click
E - 18 PC Camera Module (Windows 7)
Figure E - 9 - Audio Setup for PC Camera
Windows 7
Camera Application
The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to.avi format.
1.
Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below).
2.
Go to the Capture menu heading (if you wish to capture audio check
“PC Camera Audio Setup” on page E -
3.
Click OK (the file location will be displayed in the pop-up box) to start capturing the video, and press Esc to stop the capture (you can view the file using the Windows Media Player).
Set Capture File
Prior to capturing video files you may select the Set Capture File... option in the File menu, and set the file name and location before capture (this will help avoid accidentally overwriting files). Set the name and location then click Open, then set the “Capture file size:” and click OK. You can then start the capture process as above.
Note the important information in
“Reducing Video File Size” on page E - 20
in order to save file space, and
help prevent system problems.
PC Camera Module (Windows 7) E - 19
Windows 7
Reducing Video File Size
Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Note that the Windows system requires a minimum of 15GB of free space on the C: drive system partition. In order to prevent system problems it is recommended that you save the captured video file to a location other than the C: drive (see
“Set Capture File” on page E - 19
), limit the file size of the captured video or reduce video resolution (see below).
To Reduce Video Resolution Output Size:
1.
Run the camera application program from the desktop shortcut.
2.
Go to Options and scroll down to select Video
Capture Pin....
3.
Click the Output Size drop box and select a lower resolution size in order to reduce the captured file size.
4.
Click OK.
Figure E - 10 Output Size (Video Capture Pin)
E - 20 PC Camera Module (Windows 7)
Windows 7
Eliminating Screen Flicker
If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options.
1.
Run the camera application from the desktop shortcut.
2.
Go to Options and scroll down to select Video Capture Filter....
3.
Click either 50Hz or 60Hz under PowerLine Frequency.
Camera Options
The video capture filter figure pictured here may appear slightly different for some camera modules. To adjust the anti flicker properties look under the headings Anti
Flicker/Frequency/Pow-
erLine Frequency.
Latest PC Camera
Driver Information
Check the Device Driv-
ers & Utilities + User’s
Manual disc, and any accompanying insert pages, for the latest updated information on the
PC Camera driver, which may override the information provided here, including the figures pictured.
Figure E - 10
Video Capture Filter
PC Camera Module (Windows 7) E - 21
Windows 7
Snapshot Folder
The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
If you accidentally delete or move the folder, you can create a new
Snapshot folder on the desktop in order to capture the files.
Taking Still Pictures
The camera application allows you to take still pictures.
1. Run the camera application from the desktop shortcut.
2. Go to Options and select Take Picture.
3. The picture (in JPEG format) will be placed in the Snapshot folder desktop.
on the
E - 22 PC Camera Module (Windows 7)
Windows 7
Wireless LAN (Windows 7)
If you have included an Intel® or 3rd Party Wireless LAN (or WLAN & Bluetooth combo) module in your purchase option, make sure that the WLAN module is on before installing the driver.
Use the Fn + F11 key combination (see
) to toggle power
to the Wireless LAN module. Make sure you install the drivers in the order indicated
.
Note that you need to install both the WLAN & Bluetooth drivers for the Intel and
3rd party WLAN & Bluetooth Combo modules.
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Use Fn + F11 Airplane
Mode key combination to toggle Airplane Mode
On/Off, and check the
LED indicator for the power status (see
Wireless LAN (Windows 7) E - 23
Windows 7
Intel® WLAN Driver Installation
1.
Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
2.Install WLAN Driver > Yes.
4.
Click in the check box to agree to the End User License Agreement and click Install.
5.
Click
Finish.
6. The operating system is the default setting for Wireless LAN control in Windows (see page
E - 25
).
OR
3rd Party WLAN Driver Installation
1.
Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
2.
Click
Option Drivers (button).
3.
Click 2.Install WLAN Driver > Yes.
4.
Click Next.
5.
Click Finish to restart the computer.
6. The operating system is the default setting for Wireless LAN control in Windows (see page
E - 25
).
E - 24 Wireless LAN (Windows 7)
Windows 7
Connecting to a Wireless Network in Windows 7
Make sure the Wireless LAN module is turned on.
1.
Click the taskbar notification area wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).
Network and
Sharing Center
You can also use the Net-
work and Sharing Cen-
ter control panel in
Windows (Network and
Internet) to connect to any available wireless networks.
Figure E - 11
Click Taskbar Icon
Menu & Network and Sharing Center
Wireless LAN (Windows 7) E - 25
Windows 7
Figure E - 12
Network Location
Set
2. You may need to enter a security key for any access point to which you are trying to connect.
3. Click to select a network location (e.g. Home, Work or Public).
4. Click “View or change settings in Network and Sharing Center” to access further options for the connection.
E - 26 Wireless LAN (Windows 7)
Windows 7
5.
Click the taskbar icon to see any currently connected networks.
6.
To disconnect from the wireless network you can click the taskbar wireless icon , click the active connection and then click Disconnect (button).
Security Enabled
Networks
You should try to make sure that any network you are connecting to is a secure network.
Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Figure E - 13
Click Taskbar Icon
Menu - Disconnect
Wireless LAN (Windows 7) E - 27
Windows 7
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Use Fn + F11 Airplane
Mode key combination to toggle Airplane Mode
On/Off, and check the
LED indicator for the power status (see
).
Bluetooth & WLAN Combo Module (Windows 7)
If your purchase option includes the Intel® or 3rd Party Combination Wireless
LAN & Bluetooth module then install the driver as instructed overleaf.
Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver.
Bluetooth Data Transfer
Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
E - 28 Bluetooth & WLAN Combo Module (Windows 7)
Windows 7
Intel Bluetooth Combo Driver Installation
1.
Make sure the module is powered on, and then insert the Device Drivers &
Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
3.Install Combo BT Driver > Yes.
4.
Click Next > Next.
5.
Click in the check box to accept the license and click Next > Next.
6.
Click Finish > Yes to restart the computer.
7. See
“Bluetooth Configuration in Windows 7” on page E - 30
ration instructions.
OR
3rd Party Bluetooth Combo Driver Installation
1.
Make sure the module is powered on, and then insert the Device Drivers &
Utilities + User’s Manual disc into an attached DVD drive.
2.
Click Option Drivers (button).
3.
Click
3.Install Combo BT Driver > Yes.
4.
Click Next.
5.
Click
Finish to restart the computer.
6. See
“Bluetooth Configuration in Windows 7” on page E - 30
ration instructions.
High Speed Bluetooth
Data Transfer
The Combination Wire-
less LAN & Bluetooth
module supports high speed data transfer. However to achieve such transfer speeds, both de-
vices must support high speed data trans-
fer.
To obtain high speed data transfer make sure that both the WLAN and
Bluetooth modules are powered on.
Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer.
Bluetooth & WLAN Combo Module (Windows 7) E - 29
Windows 7
Add a Device
Click Start, and click Con-
trol Panel and then click
Devices and Printers
(Hardware and Sound).
Click Add a device to search for any available
Bluetooth devices.
•
•
Bluetooth Configuration in Windows 7
1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.
2. Make the device discoverable (to do this check your device documentation).
3. Make sure the computer is not in Airplane Mode (if Airplane Mode is on then the
Bluetooth module will be off).
4. A Bluetooth icon will appear in the notification area.
5. You can then do any of the following to access the Bluetooth Devices control panel.
Double-click the notification area icon to access the Bluetooth Devices control panel.
Click/Right-click the notification area icon and choose an option from the menu.
Figure E - 14
Bluetooth Devices &
Click Icon Menu
Add a device
Right-Click Notification Area Icon
E - 30 Bluetooth & WLAN Combo Module (Windows 7)
To Add a Bluetooth Device
1.
Access the Bluetooth Devices control panel and click Add a device.
2.
Double-click the device you want to pair with the computer.
Windows 7
Pairing Options
If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code.
3.
On first connection the computer will provide you with a pairing code to be entered onto the device.
Figure E - 15
Add a Device
Bluetooth & WLAN Combo Module (Windows 7) E - 31
Windows 7
Figure E - 16
Pairing Code
Example
4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.
Pairing Codes
The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing.
5. Windows will check to see if any drivers are required to complete the pairing.
6. Follow any on-screen instructions on the computer if device drivers are required to be installed.
7. Click Close.
Figure E - 17
Pairing Complete &
Bluetooth Device
Enabled
E - 32 Bluetooth & WLAN Combo Module (Windows 7)
To Change Settings for the Bluetooth Device
1.
Click the notification area icon and select Show Bluetooth Devices.
2.
Right-click on the device you want to change and click Properties to:
• Change the name of the device (click Bluetooth, type a new name and click OK).
• Enable/Disable a service (click Services, clear/check the check box next to the service and click OK).
To Make your Computer Discoverable to Bluetooth Devices
1.
Click the notification area icon and select Open Settings.
2.
Click Options, and make sure that Allow Bluetooth devices to find this
computer check box (Discovery) has a check inside it.
3.
Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a check inside it, if you want to be notified when a
Bluetooth device wants to connect.
Windows 7
Bluetooth Help
To get help on Bluetooth configuration and settings, select Help and
Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information.
Figure E - 18
Bluetooth Settings -
Options
Bluetooth & WLAN Combo Module (Windows 7) E - 33
Windows 7
3G/4G Module (Windows 7)
If you have included an optional UMTS/HSPA+ based 3G Module (Universal Mobile Telecommunications
System or
High Speed Packet Access) module or LTE (Long Term Evolution) 4G module (see
for specification details) in your purchase option, you will have the appropriate application
(Mobile Partner) provided for Windows 7 (Windows 8.1 does not require a driver/application). Follow the instructions on page
to install the USIM card (which will be provided by your service provider), and then install the application.
Important Notice - 3G & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3G module and the
Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G module is powered on, make sure that the Bluetooth/
Wireless LAN modules are powered off.
Wireless Device Operation Aboard Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN, Bluetooth and 3G/4G module(s) are OFF (or the system is in
Airplane Mode) if you are using the computer aboard aircraft (see
).
E - 34 3G/4G Module (Windows 7)
Windows 7
3G/4G Module USIM Card Installation
Follow the instructions below to install the USIM card (which will be provided by your service provider).
1.
Turn the computer off, and turn it over.
2.
Slide the latch
1
in the direction of the arrow.
3.
Slide the latch
2
in the direction of the arrow, and hold it in place.
4.
Slide the battery out in the direction of the arrow
3
.
5.
Insert the USIM card
4
as illustrated below until it clicks fully into position, and replace the battery.
1 2
3
Power Safety
Warning
Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
USIM Card Orientation
Note that the USIM card’s readable side (with the gold-colored contacts) should face upwards as illustrated.
4 5
Figure E - 19
Battery Removal &
USIM Card Insertion
3G/4G Module (Windows 7) E - 35
Windows 7
Mobile Partner
With the 3G/4G module and USIM card (supplied by your service provider) installed you may then install the
Mobile Partner application to directly access your 3G/4G internet service from the computer.
Mobile Partner Application Installation
1.
Make sure the system is not in Airplane Mode.
2. If a Found New Hardware window appears, click Cancel (click Cancel for all Found New Hardware windows that appear).
3. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
4. Click Option Drivers (button).
5. Click 4.Install 3G Driver > Yes.
6. Click Next > Install > Finish > Next.
7. Click I Agree (button) to accept the license agreement.
8. Click Install > Finish.
9. Choose the language you prefer and click OK, and then click Next.
10. Click I Agree (button) to accept the license agreement.
11. Click Next > Install > Finish.
12. Click Finish to restart the computer.
13. Access the Mobile Partner application from the Start menu (Start > Programs/All Programs >
Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop.
E - 36 3G/4G Module (Windows 7)
Windows 7
Mobile Partner Application
You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page.
Profile Management
1.
Make sure the system is not in Airplane Mode.
2.
Access the Mobile Partner application from the Start menu (Start > Programs/All
Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop .
3.
If you have not created a profile, click Tools and select Options, and then click
Profile Management.
4.
Click New and input the appropriate information for Profile Name, APN and Authentication etc. as supplied by your service provider.
5.
Click Save to save the profile.
Mobile Partner Help
To get help on Mobile
Partner configuration and settings, click the
Help menu and select
Online Help or press
F1.
Figure E - 20
Profile Management
3G/4G Module (Windows 7) E - 37
Windows 7
Figure E - 21
Connect
Connecting to the Service Provider
1. Make sure the system is not in Airplane Mode.
2. Access the Mobile Partner application from the Start menu (Start > Programs/All
Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop .
3. The software will run and you can select the Profile Name from the menu.
4. Click Connect to begin the connection process.
5. The Mobile Partner application will then display the connection information.
Figure E - 22
Network
Connection Prompt
E - 38 3G/4G Module (Windows 7)
6.
While connected you can also click the icon in the notification area of the taskbar to display the Windows 7 Mobile Broadband connection status.
Windows 7
Figure E - 23
Connected
Taskbar
Notification Area
Notification
7.
You can then access the internet, download e-mail etc. as per any internet connection.
3G/4G Module (Windows 7) E - 39
Windows 7
8. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons.
9. To disconnect click the Disconnect icon, or right click the notification area icon and select Disconnect (you can also select the connection in the Mobile
Broadband connection status window, and click Disconnect).
Figure E - 24
Disconnect
10. The program will disconnect from the service provider.
E - 40 3G/4G Module (Windows 7)
11. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection.
Windows 7
Figure E - 25
Exit Prompt
12. Exiting the program terminates the connection, but DOES NOT turn off the 3G module, and you will need to put the system into Airplane Mode to do so (pay
careful attention to this aboard aircraft - see
“Wireless Device Operation Aboard
).
13. If the module is on and the computer enters a power-saving state, then the power status of the module on resuming from the power-saving state will be as below:
• If the 3G module is on and the computer is Shut Down or Restarted; the module will be off when the computer starts up.
• If the 3G module is on and the computer enters Sleep or Hibernate; the module will be off when the computer resumes from sleep.
3G/4G Module (Windows 7) E - 41
Windows 7
Text Messaging Service
In addition to standard internet services you may also send and receive SMS text messages using the Mobile
Partner program, if your service supports SMS.
Reading SMS Messages
1.
An icon will blink at the bottom of the Mobile Partner interface to notify you of any new messages received.
2.
Click the Text icon in the Mobile Partner Interface.
3.
Select the Local > Inbox or SIM/USIM Card folder and select any message to read it.
4.
Right-click the message and choose an option to reply, forward or delete the message.
Creating and Sending SMS Messages
1.
Click the Text icon in the Mobile Partner Interface.
2.
Click the New button .
3.
Enter the recipient’s number in the Send To... field or click the Send To... button to select an entry from the phone book, and click OK.
4.
Type in the message details.
5.
Click the Send button, Save button to send the message later or Close > Yes to save in the Draft folder.
For more details on SMS click the Help menu and select Online Help or press F1 and select SMS.
E - 42 3G/4G Module (Windows 7)
Windows 7
Intel Rapid Storage Technology (Windows 7)
Install the Intel Rapid Storage Technology to support your SATA drive set up in AHCI mode in the BIOS (see
“SATA Mode (Advanced Menu)” on page 5 - 7
).
IRST Driver Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc an attached DVD drive.
2. Click Option Drivers (button).
3. Click 5.Install IRST Driver > Yes.
4. Click Next.
5.
Click in the check box to accept the license and click Next.
6. Click Next > Next > Next.
7. Click Finish to restart the computer (you will need to restart the system again after the computer has rebooted).
8. Run the Intel® Rapid Storage Technology application from the Start menu.
Intel Rapid Storage Technology (Windows 7) E - 43
Windows 7
Compatible
Adapters
For a list of compatible display and audio adapters check the Intel website, or your distributor/ supplier.
Intel
®
Wireless Display Application (Windows 7)
The Intel
® Wireless Display Application (requires Intel® Centrino WLAN/
Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your
TV/external display without using HDMI or A/V cables.
Before configuring the Intel® WiDi application you will need to set up your com-
patible adapter with your display/speakers. Connect the adapter using an HDMI or
A/V cable and turn on the display (or in the case of speakers connect them to the wireless speaker adapter with the cables provided with the adapter), and then set the display to the appropriate input channel (see the documentation supplied with your
compatible adapter for full details).
Intel ®
WiDi also incorporates Intel® Wireless Music which allows you to wirelessly stream audio from your computer to speakers connected to a compatible wire-
less speaker adapter (purchased separately).
E - 44 Intel® Wireless Display Application (Windows 7)
Intel
®
WiDi Application Installation
1.
Insert the Device Drivers & Utilities + User’s Manual disc an attached DVD drive.
2. Click Option Drivers (button).
3. Click 6.Install WiDi AP > Yes.
4. Click Next.
5. Click the button to accept the license and click Next.
6. Click Finish.
Windows 7
Intel® Wireless Display Application (Windows 7) E - 45
Windows 7
Intel
®
WiDi Application Configuration
1. Click Start > All Programs > Intel Corporation > Intel(R) Wireless Display >
Intel(R) Wireless Display, or double click the icon on the desktop.
2. Click I agree to the terms of this license (button).
3. The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Figure E - 26
Intel
®
WiDi Scan
E - 46 Intel® Wireless Display Application (Windows 7)
Windows 7
4.
Click to select and detected adapters, and click Connect.
5.
The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter).
6.
Enter the code for the video adapter and click Continue.
\
Figure E - 27
Intel
®
WiDi Connect
& Enter Security
Code
Intel® Wireless Display Application (Windows 7) E - 47
Windows 7
Test Audio Adapter
To verify a successful audio connection (for In-
tel® Wireless Music), select the “Test your
audio connection” link or select “Finished” to bypass the test.
You can select “Play
Sample” to play an audio test sample from your adapter to the connected speaker set.
7. You will then be prompted to enter a name for the video adapter and click
Continue.
8. Click Finished to complete the setup.
Figure E - 28
Intel
®
WiDi
Connected
E - 48 Intel® Wireless Display Application (Windows 7)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement