LION WD256103 Instruction Manual

MODEL NO: WD256103
30” Warming Drawer, Rated 120V, 60 Hz,450W, 4A
TABLE OF CONTENTS
P
A
G
E
SAFETY INSTRUCTIONS......................................................................................................................... 2
INSTALLATION INSTRUCTIONS ............................................................................................................. 5
OPERATING INSTRUCTIONS……………………………………………………………………………………………6
CLEANING & MAINTENANCE……………………………………………………………………………………………7
TROUBLE SHOOTING GUIDE ................................................................................................................. 7
SPECIFICATIONS & ASSEMBLY INSTRUCTION .................................................................................... 8
CIRCUITRY OF WARMING DRAWER COMPONENTS LIST................................................................... 9
WARRANTY............................................................................................................................................ 10
1
Certificate
Project
Figure No.
Version A
SAFETY INSTRUCTIONS
Read all instructions carefully before operating your warming drawer
Important: Observe all governing codes and ordinances.
It is the customer’s responsibility: To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in conformance with National
Electrical Code- ANSI/NFPA 70-latest edition and all local codes & ordinances.
You must have:
A. 120-volt, 60Hz, AC-only, 15-or 20- amp fused electrical supply.
B. outlet located in the cabinet as close as possible to the warming oven.
We recommend:
A. a time-delay fuse or circuit breaker.
B. a separate circuit serving this appliance only.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
Copies of the standards listed may be obtained from:
*National Fire Protection
Association 1 Batterymarch Park
Quincy, MA 02169
For your personal safety, this appliance must be grounded. This is equipped with a
power supply cord having 3- prong ground plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong ground- type outlet, grounded in accordance
with local codes and ordinances. See Figure 1. If a mating outlet is not available, it is the
personal responsibility and obligation of the customer to have a properly grounded
3-prong outlet installed by a qualified electrician.
Warning – Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman. If you are in doubt as to
whether the appliance is properly grounded. Do not modify the plug provided with appliance
2
Certificate
Project
Figure No.
Version A
IMPORTANT INSTRUCTION
1.
Read all instructions.
2.
Do not touch hot surfaces. Use handles or knobs.
3.
To protect against electrical shock do not immerse heater elements in water or other liquid.
4.
Close supervision is necessary when any appliance is used by or near children.
5.
Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or
taking off parts.
6.
Do not operate any appliance with damaged parts or after the appliance malfunctions or has
been damaged in any manner. Return appliance to the nearest authorized service facility for
examination, repair, or adjustment.
7.
The use of accessory attachments not recommended by the appliance manufacturer may
cause injuries.
8.
Do not use appliance for other than the intended use.
9.
Save these instructions.
10.
To reduce the risk of fire, do not place any heating or cooking appliance beneath the
appliance.
11.
To reduce the risk of fire, do not mount unit over or near any portion of a heating or cooking
appliance.
12.
To reduce the risk of electric shock, do not mount over a sink.
13.
To reduce the risk of fire, do not store anything directly on top of the appliance surface when
the appliance is in operation.
14.
Be sure that the warming drawer is properly grounded and installed by a qualified technician.
The electrical cord has a 3 prong plug. Do not cut any of the prongs
15.
Make sure that the island is free of cracks that would allow water or other liquids to get into
the electrical controls.
16.
Keep the warming drawer away from water sprinklers.
17.
When not in use, cover the island to protect from rain and harsh weather conditions.
3
Certificate
Project
Figure No.
Version A
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock, injury to persons, or damage when
using the warming drawer, follow basic precautions, including the following:
Proper Installation – Be sure the warming drawer is properly installed and grounded by a
qualified technician.
Do Not Leave Children Alone – Children should not be left alone or unattended in area where
warming drawer is in use. They should never be allowed to sit or stand on any part of the
warming drawer.
Wear Proper Apparel – Loose-fitting or hanging garments should never be worn while using the
warming drawer.
User Servicing – Do not repair or replace any part of the warming drawer unless specifically
recommended in the manual. All other servicing should be referred to a qualified technician.
Storage in Warming Drawer – Flammable materials should not be stored in a warming drawer.
Do Not Use Water on Grease Fires – Smother fire or flame or use dry chemical or foam-type
extinguisher.
Use Care When Opening Door – Let hot air or steam escape before removing or replacing food.
Use Only Dry Potholders – Moist or damp potholders on hot surfaces may result in burns from
steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.
Do Not Heat Unopened Food Containers – Build-up of pressure may cause container to burst
and result in injury.
Placement of Warming Drawer Racks – Always place warming drawer racks in desired location
while warming drawer is cool. If rack must be moved while warming drawer is hot, do not let
potholder contact hot heating element in warming drawer.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SUFACES OF WARMING DRAWER Heating elements may be hot even though they are dark in color. Interior surfaces of a
warming drawer become hot enough to cause burns. During and after use, do not touch, or let
clothing or other flammable materials contact heating elements or interior surfaces of warming
drawer until they have had sufficient time to cool. Other surfaces of the warming drawer may
become hot enough to cause burns – among these surfaces are warming drawer vent
openings and surfaces near these openings and warming drawer doors.
SAVE THESE INSTRUCTIONS
4
Certificate
Project
Figure No.
Version A
INSTALLATION INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Provide a 10” x 28 1/2” cutout to the front of the island
Provide support beams using metal studs.
Pull the drawer out of the drawer casing to gain access on the mounting holder at the front of
the casing.
Insert the drawer casing into the island opening.
Secure the drawer casing with screws at the inside front top and bottom, using the pre-punched
mounting holes.
Re-assemble the drawer section into the drawer casing.
Apply weather proof sealant along the edges of the warmer.
Plug-in the warmer to a weather proof, and properly grounded, electrical outlet.
BBQ island must be made of non combustible materials, check local building codes.
5
Certificate
Project
Figure No.
Version A
OPERATING INSTRUCTIONS
Temperature Controls
Use knob to control the temperature, open the right drawer. Firstly, turn on the switch to “I”.
When “Power” lights up, the knob is point to “OFF “at 6 o’clock direction.
Then switch the knob by clockwise, the “WARMING” will light on. At 9 o’clock direction is heating
slowly; at 12 o’clock direction is 150℉, and at 3 o’clock direction the temperature can reach to
250℉. Switch the knob to “OFF” after using, then turn off the switch to “O”.
The warming drawer should only be opened when adding or removing food. Continuous opening
of the drawer allows warm air to escape and make the food colder.
Do not use aluminum foil to line the drawer. It is an excellent eat insulator and will
trap heat beneath it. This may affect the performance of the warming drawer and the
interior finish.
Moisture Vent Control
Moisture Exhaust control is at the top of drawer panel, those two areas with small holes. The
switch croonltis at the inter nal groove of drawer panel, for vent control, when you pull the
switch control to the middle, it’s “ON". When you pull the switch control outward, it's "OFF"
Heating Instructions
a. The main function of the warming drawer is to hold hot cooked foods at serving
temperature.
b. Place previously prepared foods directly into the empty Food Pans (no water) and set
the moisture vent control.
c. For crispy foods, slide the moisture vent control inward to open the vents and allow the
moisture to escape.
d. Set the temperature control dial. Heat-on light will appear until the desired
temperature is reached.
e. For moist food, slide the moisture vent control outward to close the vents and seal the
moisture inside the drawer.
Proofing Yeast Dough
a. Yeast dough can be proofed in a warming drawer.
b. Place the dough in a bowl and turn the temperature control at the lowest setting, to
facilitate the fermentation process.
c. Place a towel over the dough to minimize surface drying.
d. Let the dough remain in the warming drawer until it has doubled in size and a slight
depression remains when the surface is touched gently with a finger.
6
Certificate
Project
Figure No.
Version A
CLEANING & MAINTENANCE
The Warming Drawer is made of welded #304 stainless steel. It is non-rusting and
non-magnetic.
1.
Allow the warming drawer and its accessories to cool before cleaning.
2.
Remove steam pans and all accessories from warming drawer.
3.
Clean all items including the drawer with the mildest cleanser. Scrub dirt with sponge.
4.
When cleaning the front panel, always scrub in the direction of the grain. In order to
maintain the luster and highlights of polished surface, do not use abrasives when cleaning
polished surfaces. Use the mildest cleaner.
5.
Do not use steel wool to clean the drawer and accessories.
6.
Check out the slide rails and make sure they are clean and free from debris.
7.
lt is highly recommended to clean the warming drawer after every use.
Trouble Shooting Guide
Problem
What To Do
1. Warming drawer will not heat up.
2. Heat-on light does not come “on”.
1. Call your dealer, or authorized
service agency.
2. Check if the temperature control
dial is set properly.
3. Check if the circuit breaker is open.
If service is required:
1. Call your dealer, or authorized
service agency.
2. Provide the following information:
a. Model number
b. Serial number
c. Date purchased
d. Name of dealer where the unit
was purchased from
7
Certificate
Project
Figure No.
Version A
SPECIFICATIONS & ASSEMBLY
INSTRUCTION
ITEM# STAINLESS STEEL WARMING DRAWER
8
Certificate
Project
Figure No.
Version A
SPECIFICATIONS & ASSEMBLY
INSTRUCTION
ITEM# STAINLESS STEEL WARMING DRAWER
N
Part list
Qty
1
Heating Element
1
2
Switch
1
3
Chrome Bezel
1
4
Control Knob
1
5
Bolt
4
6
Washer
4
7
Sleeve
4
8
Power Light
1
9
Heat on Light
1
10
Roller Guides
2
11
Handle Bracket
2
12
Drawer Handle
1
13
Food pan (L)
1
14
Food pans (S)
4
9
Certificate
Project
Figure No.
Version A
CIRCUITRY OF WARMING DRAWER
COMPONENTS LIST
1
2
(UL)KW TI-8
250V-16A
WARMING LIGHT
APT R CE
AD16-16D
4
120V
PRONIC
15A 125VAC
GROUND WIRE
6
POWER LIGHT
APT R CE
AD16-16D
120V
3
7
WIRE NUTS
5
(UL)SJTW 105 C VW-1 18AWGx3C E137357 191710
C(UL)SJTW 105 C FT-1 18AWGx3C
NO
Part list
Q'ty
1
2
3
Heating Element
Switch
Plug
1
1
1
4
Knob of Temperature
1
5
Power Light
1
6
Heat on Light
1
7
Wire nuts
1
10
Certificate
Project
Figure No.
Version A
Lion Exterior Products, Inc.
Ontario, California 91761
LIMITED WARRANTY
Lion Exterior Products, Inc. warrants to the original purchaser at the original site of delivery with proof of purchase of warming
drawer that when subject to normal residential use,it is f ree from defects in workmanship and materials for the periods specified
below.It does not apply to rust, corrosion, oxidation or discoloration, which may occur due to moisture or overheating, unless the
affected component becomes inoperable. It does not cover labor or labor related charges. There will be shipping and handling
charge for the delivery of the warranty part(s).
Component
Warranty Period
Warming drawer…………………………………………………………
Parts
…………………………………………………
1 Year
Repair only, no labor
Our obligation under this warranty is limited to repair or replacement, at our option, of the product during the warranty period. The
extent of any liability of Lion Exterior Products, Inc., under this warranty is limited to repair or replacement. This warranty does
not cover normal wear of parts, damage resulting from any of the following: negligent use or misuse of the product, use on
improper fuel/gas supply, use contrary to operating instructions, or alteration by any person other than our factory service center
The warranty period is not extended by such repair or replacement.
For customer service, contact the authorized selling dealer immediately. If you need additional information or assistance, please
contact the Lion Exterior Products Inc. 541 East Main St., Ontario CA 91761 or visit lionbbq.com
Product repair as provided under this warranty is your exclusive remedy. Lion Exterior Products, Inc. shall not be liable for any
incidental or consequential damages for breach of any express or implied warranty on its products. Except to the extent prohibited
by applicable law, any implied warranty or merchantability or fitness for a particular purpose on this product to the duration of the
above warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations
on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may have other rights, which vary from state to state. Lion Exterior Products Inc. shall not be liable
for loss of use of the warming drawer, related hardware or other in cidental or consequential costs, expense or damages, which may
include, but are not limited to, removal of permanent deck or other custom fixtures or the necessity for crane removal. Any
implied warranty shall have duration equal of the applicable warranty stated above.
Drawer Model
Date of Purchased
Drawer Serial Number
Purchased From
11
Certificate
Project
Figure No.
Version A