Spear & Jackson SPJBV 3200 Petrol Leaf Vacuum Instructions

Operating Instructions Garden Blower Vac
34.360.05
Cat-No.: 720-0353
I.-No.: 01017
SPJBV
3200

Please read these instructions carefully
before installing and operating the
Garden blower vac!
Petrol Engine Quick Start Guide
Ensure correct fuel/oil mixture 40:1
STARTING
1. Make sure that the Vacuum Bag is fitted correctly,
failure to do so and the engine will not start.
2. Set the ON/OFF switch to “I”
3. Press the throttle trigger until it locks.
4. Press the fuel primer ten times.
5. Set the choke lever to “I I”.
6. Hold the machine on the front lever.
7. Pull the starter cable 4 times quickly.
8. Allow the machine to warm up for approx. 10 seconds.
9. Set the choke lever to “I I”
Note - this quick start guide is intended for
experienced users who have already assembled the
tool, please refer to the manual for details.
If machine does not start after minimum 6 pulls on starter
cord refer to petrol Engine Q & A on page 13.
2
1
6
8
4
5
3
2
1
7
13
11
12
9
17
10
18
15
14
16
A
1A
1B
D
C
C
B
3
2
A
3
B
4A
B
4B
A
4C
D
C
4D
4E
D
5
7A
6
A
7B
B
8
9
C
B
.025 in.
(0,6 mm)
4
GB
Read the operating instructions before you use the
blower vac.
Fuel pump
Wear safety goggles to protect your eyes. Wear ear
protectors to protect your hearing against the noise.
Never work if people – especially children - or
animals are in the danger area.
Warning! Hazard!
Never allow the blower to run without the blower
tube.
Keep other people away.
Sound power level with EC Directive 2000/14/EC!
Warning! Hot surface
After the unit is switched off, the motor continues to
run for a short while.
5
GB
Table of contents
Page
1. General safety regulations
2. Machine layout and items supplied
3. Technical data
4. Assembly
5. Operating Instructions
6. Maintenance
7. Storage
8. Ordering replacement parts
9. Troubleshooting
10. Starting procedure
7
8
8
8
9
10
10
11
12
13
6
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
1. GENERAL SAFETY REGULATIONS
READ YOUR USER MANUAL AND ALL SUPPLEMENTS
(IF ANY ENCLOSED) THOROUGHLY BEFORE
OPERATING YOUR UNIT.
1. WEAR CLOSE FITTING, TOUGH WORK CLOTHING
PPE (Personal protective clothing) that will provide
protection/without restricting your movements, such as
long slacks or trousers, safety work shoes, heavy duty
work gloves, hard hat, a safety face shield, or safety
glasses for eye protection and a good grade of ear plugs
or other sound barriers for hearing protection.
2. REFUEL IN A SAFE PLACE. Open fuel cap slowly to
release any pressure which may have formed in fuel tank.
Always wipe unit of fuel or oil spills before starting. To
prevent a fire hazard, move at least 10 feet (3 meters)
from fueling area before starting.
3. TURN UNIT OFF before setting it down, and also before
installing or removing attachments.
4. KEEP ALL SCREWS AND FASTENERS TIGHT and the
unit in good operating condition. Never operate this
equipment if it is improperly adjusted or not completely
and securely assembled.
5. KEEP HANDLES DRY, clean and free of fuel mixture.
6. STORE EQUIPMENT AWAY FROM POSSIBLE
IGNITION SOURCES, such as gas-powered water
heaters, clothes dryers, or oil-fired furnaces, portable
heaters, etc.
7. ALWAYS KEEP the engine free of debris build-up.
8. OPERATION OF EQUIPMENT should always be
restricted to mature and properly instructed individuals.
9. ALL PERSONS WITH RESPIRATORY PROBLEMS and
persons operating blower in very dusty environments,
should wear a dust particle mask at all times. Paper dust
masks are available at most paint and hardware stores.
10. Use the blower vac only at reasonable times of the day.
Do not use early in the morning or late in the evening
when people could feel disturbed. Pay attention to your
local noise control regulations.
11. Allow the machine to run at the lowest possible motor
speed required to carry out the work.
12. Before you start work, use a brush and scraper to remove
all dirt from the blower vac.
13. In case of dusty conditions, moisten the surface a little.
14. Use the full-length blower nozzle extension so that the air
current can work near to the ground.
15. Watch out for children, pets, open windows etc. and blow
the dirt safely away from them.
WHAT NOT TO DO
WARNING: DO NOT USE ANY OTHER FUEL than that
recommended in your manual. Always follow instructions in
the Fuel and Lubrication section of this manual. Never use
gasoline unless it is properly mixed with 2-cycle engine
lubricant. Permanent damage to engine will result, voiding
manufacturerʼs warranty.
1. DO NOT SMOKE while refueling or operating equipment.
2. DO NOT OPERATE UNIT WITHOUT A MUFFLER and
properly installed muffler shield.
3. DO NOT TOUCH or let your hands or body come in
contact with a hot muffler or spark plug wire.
4. DUE TO THE DANGER of exhaust fumes, never operate
blower in a confined or poorly ventilated area.
5. NEVER POINT BLOWER in the direction of people,
animals, buildings, automobiles, or windows, etc.
6. DO NOT operate unit without inlet cover installed to
prevent contact with impeller.
7. DO NOT set a hot engine down where flammable material
is present.
8. DO NOT OPERATE UNIT FOR PROLONGED PERIODS.
Rest periodically.
9. DO NOT OPERATE UNIT WHILE UNDER THE
INFLUENCE OF ALCOHOL OR DRUGS.
WARNING: DO NOT ADD, REMOVE OR ALTER ANY
COMPONENTS OF THIS PRODUCT. Doing so could cause
personal injury and/or damage the unit voiding the
manufacturerʼs warranty.
10. DO NOT operate your unit near or around flammable
liquids or gases whether in or out of doors. An explosion
and/or fire may result.
11. DO NOT WEAR loose clothing, scarfs, neck chains,
unconfined long hair, and the like. Doing so could cause
injury associated with objects being drawn into the rotating
parts. Tie up long hair and fasten it, for example with a
head scarf, cap, helmet, etc.
12. DO NOT refuel a running engine or an engine that is hot
13. Never allow children to use the blower vac.
7
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
2. Machine layout and items supplied (Fig. 1)
1.Rear Handle
2.Throttle Trigger
3.Throttle Lock
4.On/Off Switch
5.Front Handle
6.Muffler Cover
7.Fuel Tank Window
8.Fuel Cap
9.Starter Handle
10.Air Filter Cover
11.Vacuum/Blower Tube
12.Choke Lever
13.Spark Plug Wire / Spark Plug
14.Vacuum/Blower Slide
15.Primer Bulb
16.Harness
17.Vacuum Bag
18.Speed Cleaner Head
WARNING: Never use straight petrol in your unit. This will
cause permanent engine damage and void the manufacturerʼs
warranty for that product. Never use a fuel mixture that has
been stored for over 90 days.
WARNING: Use only Class I 2-stroke oil suitable for air-cooled
engines.
앬
MIXING FUEL
Ensure mixing bottle cap is secured correctly and check
that the gap does not leak, then. Mix the fuel with 2-stroke
oil in a mixing bottle provided. Shake the container gently to
ensure that it is properly mixed.
앬
FUEL AND LUBRICATION
Petrol and Oil
Mix 40:1
3. Technical data
Engine
Max. Air Velocity
Max. Air Volume
Max. Engine Speed
Collection Bag
Mulching Ratio
Fuel Capacity
Weight
Maximum Engine Performance
Sound power level LWA
Sound pressure level at ear LpA
Vibration ahv
24 cm3
ca. 145 km/h
236 m3/h
7.800 ± 500 min-1
55 Litre
10:1
650 ml
7.65 kg
0.8 kW/1.1 HP
108 dB(A)
95 dB(A)
13.69 m/s2
4. ASSEMBLY
앬 SUCTION TUBE (FIG. 1A + 1B)
1. Release the screws (A) and remove the screw (B). Insert
blower tube (C) into the blower housing and replace screw
(B). Tighten screws (A).
2. Insert speed cleaner head (D) to the tube (C).
앬
HARNESS INSTALLATION (FIG .2)
Attach the 2 harness clips to the 2 links in the blower
handle.
앬
VACUUM ATTACHMENT ASSEMBLY INSTRUCTIONS
To install vacuum bag:
Pull the slide (A) forward and fit bag (B) into the vacuum
housing. (See Fig. 3)
앬
FUEL
Use regular grade unleaded petrol mixed with 40:1 custom
2-cycle engine oil for best results.
앬
RECOMMENDED FUELS
Some conventional petrols are being blended with
oxygenates such as alcohol or an ether compound to meet
clean air standards. Your engine is designed to operate
satisfactorily on any gasoline intended for automotive use
including oxygenated gasolines.
5. OPERATING INSTRUCTIONS
앬
STARTING A COLD ENGINE
Fill fuel tank with proper fuel and oil mixture. See Fuel and
Lubrication.
Set unit on ground so that it rests on housing feet.
1. Pull the throttle trigger (A). (It will auto lock) Fig. 4A.
2. Prime the carburetor. Pump the primer bulb (C) 10 times
(Fig. 4B).
3. Your unit is designed with a 2 position choke (D): START
“ ” and RUN “ ”. Move choke lever to START “ ”
position (Fig. 4C).
4. Grip handle firmly .
5. Pull starter rope out a short way until resistance is felt
(approximately 100mm). Pull starter rope quickly and
everly until engine starts or attempts to run. Once engine
starts, warm up at full throttle for 10 seconds and release
throttle.
6. Push down the throttle lock (B), the throttle trigger (A) will
go back to the nomal position. (Fig. 4A)
7. Move the choke to RUN “ ” position (Fig. 4E).
NOTE: If engine fails to start after repeated attempts, refer to
Troubleshooting section.
NOTE: Always pull starter rope straight out. Pulling starter at
an angle will cause rope to rub against the eyelet. This friction
will cause the rope to fray and wear more quickly. Always hold
8
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
starter handle when rope retracts. Never allow rope to snap
back from extended position. This could cause rope to snag or
fray and also damage the starter assembly.
앬
STOPPING THE ENGINE
Emergency Stopping Procedure. When it is necessary to
stop blower engine immediately, DEPRESS the switch to stop.
Normal Stopping Method. For normal stopping, push down
the throttle lock, the throttle trigger will back to the nomal
position and allow engine to return to idle speed. Then
DEPRESS and HOLD the “OFF” switch until the engine stops
completely.
앬
STARTING A WARM ENGINE (Engine has been stopped
for no more than 15-20 minutes)
1. Pull starter rope again. Engine should start with ONE or
TWO pulls. If engine fails to start after 6 pulls, repeat steps
2 through 6 (see Starting a cold engine).
2. If engine does not start, or starts and then stops after 5
rope pulls, follow procedure “STARTING A COLD
ENGINE”.
앬
BLOWER OPERATIONS (FIG. 5)
Your blower is designed to easily remove debris from patios,
walkways, lawns, bushes, etc., and many hard to reach areas
where debris may accumulate.
WARNING: Because of flying debris, always wear American
National Standards Institute (A.N.S.I.) approved shielded safety
glasses or face shield when operating blower.
Before using your blower, review Safety Precautions in your
User Manual, and all regulations for operation of the unit.
These precautions and regulations are for your protection.
CAUTION: Hold the blower so that hot exhaust does not
damage clothing and fumes are not inhaled by operator.
DO NOT operate the blower with other people or animals in
the immediate vicinity. Allow a minimum of 30 feet (9 meters)
between operator and other people or animals.
We recommend that a face mask be worn when operating
blower in dusty areas.
Stand away from the debris, at a distance that will easily allow
you to control the direction of blown debris. Never blow debris
in direction of bystanders.
To control velocity of airstream, blower can be operated at any
speed between idle and full throttle. Experience with the unit
will help you determine the amount of airflow necessary for
each application.
앬
cigarettes. Do not operate unit near open flame.
CAUTION: This unit is designed to vacuum up debris such as
leaves, small bits of paper, small twigs, weeds, grass
clippings, etc. Do not use this unit for any other purpose.
Do not attempt to vacuum rocks, broken glass, bottles, tin
cans or other such objects. Damage to impeller and unit as
well as operator injury could result.
If vacuum tube is level with power unit horizontal, rocks or
large objects may be drawn into tube, damaging the impeller.
To Operate Vacuum:
1. Follow correct starting procedures as explained in this
manual.
2. Allow engine to return to idle. Put the shoulder harness on
so the strap is over your right shoulder. Put the vacuum
bag strap on so it is over your left shoulder.
CAUTION: Do not allow shoulder harness to cover, block, or
come in contact with exhaust outlet during operation. The
muffler generates heat and could burn, melt, or damage
harness strap.
3. Place your left hand on the top handle and right hand on
side handle as shown (Fig. 6).
4. Swing unit side to side to vacuum debris.
CAUTION: To avoid clogging vacuum tube. DO NOT FORCE
OR PLACE SUCTION TUBE INTO A PILE OF DEBRIS.
앬
VACUUM TUBE CLOGGING
To Unclog Vacuum Tube:
1. Turn engine “OFF”. Promptly compress vacuum bag while
it is still inflated, expelling air out of the suction tube.
This reverse airflow is usually sufficient to dislodge most
obstructions. If the obstruction cannot be cleared by
compressing vacuum bag, follow this procedure:
2. Remove and inspect vacuum tubes.
3. Carefully clean out nozzle.
4. Reinstall vacuum tubes.
VACUUM OPERATIONS
WARNING: NEVER OPERATE VACUUM WITHOUT
VACUUM BAG PROPERLY ATTACHED, AS FLYING
DEBRIS COULD CAUSE INJURY TO OPERATOR AND
BYSTANDERS. ALWAYS MAKE SURE VACUUM BAG
ZIPPER IS CLOSED BEFORE OPERATING UNIT.
Do not vacuum hot or burning materials (e.g. hot ash, glowing
cigarettes) from outdoor fireplaces or barbecue pits. always
wait for these materials to be cool enough. Do not vacuum
lighted smoking material such as discarded cigars or
9
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
6. Maintenance
앬
7. Storage
7.1 STORING A UNIT
AIR FILTER
CAUTION: NEVER operate blower without the air filter or dust
and dirt will be sucked into the engine and damage it. The air
filter must be kept clean. If it becomes damaged, install a new
filter.
To Clean Air Filter(FIG .7A + 7B):
1. Remove 2 screws (A) holding air filter cover in place,
remove cover (B) and lift filter (C) from cover
2. Wash filter in soap and water. DO NOT USE PETROL!
3. Air dry filter.
4. Reinstall air filter and air filter cover.
NOTE: Replace filter if frayed, torn, damaged or unable to be
cleaned.
앬
CARBURETOR ADJUSTMENT
The carburetor was pre-set at the factory for optimum
performance. If further adjustments are necessary, please
take your unit to the nearest professional.
앬
SPARK PLUG (FIG .8)
1. Spark plug gap = .025 in.
(0,6 mm)
2. Torque to 105 to 130 inch pounds (12 to 15 Nm). Connect
spark plug boot.
앬
VACUUM BAG CLEANING
A dirty bag will obstruct airflow, thereby reducing vacuum
efficiency.
To Clean Bag:
1. Detach vacuum bag from unit.
2. Open zipper and remove contents.
3. Turn bag INSIDE OUT and shake vigorously. This
procedure should be performed on a regular basis.
4. Turn bag RIGHT SIDE OUT, close zipper and attach to
unit.
NOTE: If vacuum bag is unusually dirty, it should be washed
by hand in warm water with a mild detergent. Rinse
thoroughly. Let dry before using.
WARNING: Failure to follow these steps may cause varnish to
form in the carburetor and difficult starting or permanent
damage following storage.
1. Perform all the general maintenance recommended in the
Maintenance Section of your User Manual.
2. Clean outside surface of unit.
3. Drain fuel from the fuel tank.
4. After fuel is drained, start engine.
5. Run engine at idle until unit stops. This will purge the
carburetor of fuel.
6. Allow engine to cool (approx. 5 minutes).
7. Using a spark plug wrench, remove the spark plug.
8. Pour 1 teaspoon of clean 2-cycle oil into the combustion
chamber (Fig. 9). Pull starter rope slowly several times to
coat internal components. Replace spark plug.
9. Store unit in a cool, dry place away from any source of
ignition such as an oil burner, water heater, etc.
7.2 REMOVING A UNIT FROM STORAGE
1. Remove spark plug.
2. Pull starter rope briskly to clear excess oil from
combustion chamber.
3. Clean and gap spark plug or install a new spark plug with
proper gap.
4. Prepare unit for operation.
5. Fill fuel tank with proper fuel / oil mixture. See Fuel and
Lubrication Section.
8. Ordering replacement parts
Please quote the following data when ordering replacement
parts:
앬 Type of machine
앬 Article number of the machine
앬 Identification number of the machine
앬 Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Helpline Numbers:
UK:
0151 649 1500
IRE:
189 094 6244
10
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
9. TROUBLE SHOOTING THE ENGINE
PROBLEM
Unit wonʼt start or starts but will not run.
PROBABLE CAUSE
CORRECTIVE ACTION
Incorrect starting procedures.
Follow instructions in the User Manual.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an
Authorized Service Center.
Fouled spark plug
Clean / gap or replace plug.
Fuel filter plugged.
Replace fuel filter.
Debris bag mounting not fitted correctly
Check the debris bag mounting
Incorrect lever position on choke.
Move to RUN position.
Dirty air filter.
Remove, clean and reinstall filter.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an
Authorized Service Center.
Engine hesitates.
No power under load.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an
Authorized Service Center.
Runs erratically.
Incorrectly gapped spark plug.
Clean / gap or replace plug.
Smokes excessively.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an
Authorized Service Center.
Incorrect fuel mixture.
Use properly mixed fuel (40:1 mixture).
Unit starts, but engine has low power.
11
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
If after trying all of the above procedures please
call the help line for further assistance
GB
10. Starting procedure
12
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
Konformitätserklärung
k
t
p
m
O
U
q
T
B
Q
Z
z
erklärt folgende Konformität gemäß EU-Richtlinie
und Normen für Artikel
declares conformity with the EU Directive
and standards marked below for the article
déclare la conformité suivante selon la
directive CE et les normes concernant lʼarticle
verklaart de volgende conformiteit in overeenstemming met de EU-richtlijn en normen voor
het artikel
declara la siguiente conformidad a tenor de la
directiva y normas de la UE para el artículo
declara a seguinte conformidade de acordo
com a directiva CE e normas para o artigo
förklarar följande överensstämmelse enl. EUdirektiv och standarder för artikeln
ilmoittaa seuraavaa Euroopan unionin direktiivien ja normien mukaista yhdenmukaisuutta
tuotteelle
erklærer herved følgende samsvar med EUdirektiv og standarder for artikkel
заявляет о соответствии товара
следующим директивам и нормам EC
izjavljuje sljedeću uskladjenost s odredbama i
normama EU za artikl.
declarå urmåtoarea conformitate cu linia directoare CE μi normele valabile pentru articolul.
ürün ile ilgili olarak AB Yönetmelikleri ve
Normlar∂ gere©ince aμa©∂daki uygunluk aç∂kla
mas∂n∂ sunar.
‰ËÏÒÓÂÈ ÙËÓ ·ÎfiÏÔ˘ıË Û˘Ìʈӛ· Û‡Ìʈӷ ÌÂ
ÙËÓ √‰ËÁ›· ∂∂ Î·È Ù· ÚfiÙ˘Ô ÁÈ· ÙÔ ÚÔ˚fiÓ
ISC-GmbH · Eschenstraße 6 · D-94405 Landau/Isar
C
l
j
A
X
W
e
1
.
G
4
H
E
dichiara la seguente conformità secondo la
direttiva UE e le norme per lʼarticolo
attesterer følgende overensstemmelse i
henhold til EU-direktiv og standarder for produkt
prohlašuje následující shodu podle směrnice
EU a norem pro výrobek.
a következő konformitást jelenti ki a termékekre vonatkozó EU-irányvonalak és normák szerint
pojasnjuje sledečo skladnost po smernici EU
in normah za artikel.
deklaruje zgodność wymienionego poniżej
artykułu z następującymi normami na
podstawie dyrektywy WE.
vydáva nasledujúce prehlásenie o zhode podľa
smernice EÚ a noriem pre výrobok.
деклаpиpа следното съответствие съгласно
диpективите и ноpмите на ЕС за пpодукта.
заявляє про відповідність згідно з Директивою
ЄС та стандартами, чинними для даного товару
deklareerib vastavuse järgnevatele EL direktiivi
dele ja normidele
deklaruoja atitikti pagal ES direktyvas ir normas
straipsniui
izjavljuje sledeçi konformitet u skladu s odred
bom EZ i normama za artikl
Atbilstības sertifikāts apliecina zemāk minēto preču
atbilstību ES direktīvām un standartiem
Samræmisyfirl‡sing sta›festir eftirfarandi samræmi
samkvæmt reglum Evfrópubandalagsins og stö›lum
fyrir vörur
Petrol blower vac SPJBV 3200
X
98/37/EG
87/404/EWG
2006/95/EG
R&TTED 1999/5/EG
97/23/EG
X
X
2000/14/EG:
LWM = 107 dB; LWA = 108 dB
P = 0.8 kW
95/54/EG:
89/336/EWG_93/68/EEC
90/396/EWG
X
97/68/EG:
e4*97/68SH2G3*2004/26*0109*04
89/686/EWG
EN ISO 14982; KBV V
Landau/Isar, den 19.03.2007
Weichselgartner
General-Manager
Art.-Nr.: 34.360.05
I.-Nr.: 01017
Subject to change without notice
Wimmer
Product-Management
Archivierung: 3436000-02-4160270
13
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GUARANTEE CERTIFICATE
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In
the unlikely event that your device develops a fault, please contact our service department at the
address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy
to offer our assistance under the service number printed below. Please note the following terms under
which guarantee claims can be made:
1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty
rights. We do not charge you for this guarantee.
2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted
to the rectification of these defects or replacement of the device. Please note that our devices have
not been designed for use in commercial, trade or industrial applications. Consequently, the
guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for
other equivalent activities. The following are also excluded from our guarantee: compensation for
transport damage, damage caused by failure to comply with the installation/assembly instructions or
damage caused by unprofessional installation, failure to comply with the operating instructions (e.g.
connection to the wrong mains voltage or current type), misuse or inappropriate use (such as
overloading of the device or use of non-approved tools or accessories), failure to comply with the
maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or
dust), effects of force or external influences (e.g. damage caused by the device being dropped) and
normal wear resulting from proper operation of the device.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
3. The guarantee is valid for a period of 2 years starting from the purchase date of the device.
Guarantee claims should be submitted before the end of the guarantee period within two weeks of
the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.
The original guarantee period remains applicable to the device even if repairs are carried out or parts
are replaced. In such cases, the work performed or parts fitted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work performed or parts fitted.
This also applies when an on-site service is used.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by
the scope of this guarantee or for units which are no longer covered. To take advantage of this service,
please send the device to our service address.
Argos Ltd
489-499 Avebury Boulevard
Saxon Gate West
Central Milton Keynes
MK9 2NW
Helpline Numbers:
UK:
0151 649 1500
IRE:
189 094 6244
14
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
Einhell UK Ltd
Unit 5 Morpeth Wharf
Twelve Quays
Birkenhead, Wirral
CH41 1LF
Tel. 0151 6491500, Fax 0151 6491501
The reprinting or reproduction by any other means, in whole or in part,
of documentation and papers accompanying products is permitted only
with the express consent of ISC GmbH.
Technical specifications subject to change
15
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
EH 03/2007
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
">