advertisement
LCD Monitor User Manual
24G2/24G2U/27G2/27G2U
LED backlight
1
www.aoc.com
© 2019 AOC. All Rights Reserved.
2
Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system .
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.
3
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V ~, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
4
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or with the stand:
5
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
6
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
For display with glossy bezel the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.
7
Setup
Contents in Box
Monitor
CD Manual Warranty card Stand Base
Power Cable HDMI Cable DP Cable VGA Cable USB Cable Audio Cable
Not all signal cables (HDMI / DP / VGA / USB /Audio cables), CD manual will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
8
Setup Base
Please setup or remove the base following the steps as below.
Please place the monitor on a soft and flat surface to prevent the scratch.
Setup:
Remove:
9
Adjusting the monitor
For optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
10
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
1 HDMI 2
2 HDMI 1
3 DP
4 Analog (D-Sub 15-Pin VGA cable)
5 Earphone out
6 Power
7 Line in
8 USB-PC upstream
9 USB 3.2 Gen 1
10 USB3.2Gen1+Quick Charging
11 USB 3.2 Gen 1
12 USB 3.2 Gen 1
To protect equipment, always turn off the PC and LCD monitor before connecting.
1. Connect the power cable to the AC port on the back of the monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port.
3. (Optional – Requires a video card with HDMI port) - Connect one end of the HDMI cable to the back of the monitor and connect the other end to the computer’s HDMI port.
4. (Optional
–
Requires a video card with DP port) - Connect one end of the DP cable to the back of the monitor and connect the other end to the computer’s DP port.
5. Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.
11
Freesync function
1. Freesync function is working with DP/HDMI1/HDMI2
2. Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting www.AMD.com
AMD Radeon™ RX 480
AMD Radeon™ RX 470
AMD Radeon™ RX 460
Radeon Pro Duo
AMD Radeon R9 300 Series
AMD Radeon R9 Fury X
AMD Radeon R9 360
AMD Radeon R7 360
AMD Radeon R9 295X2
AMD Radeon R9 290X
AMD Radeon R9 290
AMD Radeon R9 285
AMD Radeon R7 260X
AMD Radeon R7 260
12
Adjusting
Hotkeys
1
2
3
Source/Auto/Exit
Game Mode/<
Dial Point/>
4 Menu/Enter
5 Power
Source/Auto/Exit
When the OSD is closed, press “
When the OSD is closed, press “ models with D-Sub).
” button will be Source hot key function.
” button continuously about 2 second s to do auto configure (Only for the
Game Mode/<
When there is no OSD, press ”
<
” key to open game mode function, then press ”
<
” or “
>
” key to select game mode
(FPS, RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) basing on the different game types.
Dial Point
When there is no OSD, press Dial Point button to active Dial Point menu, and then press “
<
” or “
>
” to set Dial Point on or off.
Menu/Enter
When there is no OSD, Press to display the OSD or confirm the selection.
Power
Turn on/off the monitor.
13
OSD Setting
Basic and simple instruction on the control keys.
1. Press the
2. Press or
MENU-button to activate the OSD window. to navigate through the functions. Once the desired function is highlighted, press the functions. to activate it. If there is a sub-menu, press or to navigate through the sub-menu
3. Press or to change the settings of the selected function. Press any other function, repeat steps 2-3. to exit. If you want to adjust
4. OSD Lock Function: To lock the OSD, press and hold the then press
MENU-button while the monitor is off and power button to turn the monitor on. To un-lock the OSD - press and hold the
MENU-button while the monitor is off and then press power button to turn the monitor on.
Notes:
1. If the product has only one signal input, the item of "Input Select" is disabled.
2. If the product screen size is 4:3 or input signal resolution is native resolution, the item of "Image Ratio" is disabled.
3. One of Clear vision, DCR, Color Boost and Picture Boost functions is activated; the other three functions are turned off accordingly.
14
Luminance
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
Contrast
Brightness
0-100
0-100
to enter.
Contrast from Digital-register.
Backlight Adjustment
Standard Standard Mode
Text Text Mode
Internet Internet Mode
Eco mode
Game Game Mode
Movie Movie Mode
Sports Sports Mode
Gamma
DCR
HDR Effect
Reading
Gamma1
Gamma2
Gamma3
Off
On
OFF
HDR Picture
HDR Movie
HDR Game
Reading Mode
Adjust to Gamma 1
Adjust to Gamma 2
Adjust to Gamma 3
Disable dynamic contrast ratio
Enable dynamic contrast ratio
Adjust HDR Effect
15
Image Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
Clock
Phase
Sharpness
H. Position
V. Position
0-100
0-100
0-100
0-100
0-100
to enter.
Adjust picture Clock to reduce Vertical-Line noise.
Adjust Picture Phase to reduce Horizontal-Line noise.
Adjust picture sharpness.
Adjust the horizontal position of the picture.
Adjust the vertical position of the picture.
16
Color Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
Color Temp.
DCB Mode
DCB Demo
Red
Green
Blue
Warm
Normal
Cool sRGB
User
Full Enhance ON/OFF
Nature Skin ON/OFF
Green Field ON/OFF
Sky-blue ON/OFF
AutoDetect ON/OFF
ON/OFF
0-100
0-100
0-100
to enter.
Recall Warm Color Temperature from EEPROM.
Recall Normal Color Temperature from EEPROM.
Recall Cool Color Temperature from EEPROM.
Recall SRGB Color Temperature from EEPROM.
Recall User Color Temperature from EEPROM
Disable or Enable Full Enhance Mode.
Disable or Enable Nature Skin Mode.
Disable or Enable Green Field Mode.
Disable or Enable Sky-blue Mode.
Disable or Enable AutoDetect Mode.
Disable or Enable Demo.
Red gain from Digital-register.
Green gain from Digital-register.
Blue gain from Digital-register.
17
Picture Boost
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
to enter.
Bright Frame ON/OFF
Frame Size
Brightness
14-100
0-100
Enable/Disable Bright Frame
Adjust the Size of the Frame
Brightness Adjustment for Enhance Area
Contrast
H. position
0-100
0-100
Contrast Adjustment for Enhance Area
Adjust the horizontal position of the Frame
V. position 0-100 Adjust the vertical position of the Frame
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
18
OSD Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
to enter.
Language
Timeout
DP Capability
H. Position
V. Position
Volume
5-120
1.1/1.2
0-100
0-100
0-100
Select the OSD language.
Adjust the OSD timeout. please be noted that only DP1.2 support free sync function
Adjust the horizontal position of the OSD.
Adjust the vertical position of the OSD.
Volume Adjustment.
Transparence 0-100 Adjust the OSD.
Break Reminder ON/OFF
Break reminder if the user continuously work for more than 1hrs.
Notes:
If the DP video content supports DP1.2, please select DP1.2 for DP Capability; otherwise, please select DP1.1
19
Game Setting
1. Press MENU-button to display menu.
2. Press
3. Press
4. Press or or or
to select (Game setting), and press MENU-button to enter.
to select submenu, and press MENU-button to enter.
to adjust.
5. Press AUTO-button to exit
.
Game Mode
Shadow Control
Low input Lag
Frame Counter
FPS
RTS
Racing
Gamer 1
Gamer 2
Gamer 3 off
0-100
ON/OFF
For playing FPS (first Person Shooters) games.
Improves dark theme black level details.
For playing RTS (Real Time Strategy). Improves the image quality.
For playing Racing games, Provides fastest response time and high color saturation.
User’s preference settings saved as Gamer 1.
User’s preference settings saved as Gamer 2.
User’s preference settings saved as Gamer
3.
No optimization by Smart image game
Shadow Control Default is 50, then end-user can adjust from 50 to 100 or 0 to increase contrast for clear picture.
1. If picture is too dark to be saw the detail clearly, adjusting from 50 to100 for clear picture..
2. If picture is too white to be saw the detail clearly, adjusting from 50 to0 for clear picture
Turn off frame buffer to decrease input lag
Game Color will provide 0-20 level for adjusting saturation to get better picture.
Game Color
LowBlue Mode
Overdrive
FreeSync
0-20
Reading / Office /
Internet /
Multimedia / Off
Weak
Medium
Strong
Boost （ Motion picture response time 1ms ）
Off
ON/OFF
Off / Right-Up /
Right-Down /
Left-Down /
Left-Up
0-20
Decrease blue light wave by controlling color temperature.
Adjust the response time.
(Boost can only enable in Freesync off mode)
Adjust the FreeSync.
Display vertical scanning frequency
MBR
Note:
Boost or MBR must be above 75Hz refresh rate to start.
MBR (Motion Blur Reduction) will provide 0 – 20 levels for adjusting visible motion blur.
20
Extra
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit
.
Input Select
Auto Config.
Off Timer
Image Ratio
DDC/CI
Reset
Auto/D-SUB/HDMI1/HDMI2/DP
Yes / No
0-24 hrs
Wide
4:3
1:1
17” (4:3)
19” (4:3)
19” (5:4)
(27G2/27G2U)
19”W (16:10)
21.5”W (16:9)
22”W (16:10)
(27G2/27G2U)
23”W (16:9)
23.6”W (16:9) (27G2/27G2U)
24”W (16 :9) (27G2/27G2U)
Yes / No
Yes / No
to enter.
Select input signal source.
Auto adjust the picture to default.
Select DC off time.
Select image ratio for display.
Turn on or off DDC/CI Support.
Reset the menu to default.
21
Exit
1 Press MENU (Menu) to display menu.
2 Press or to select
3 Press to exit
.
(Luminance), and press to enter.
LED Indicator
Status
Full Power Mode
Power Saving
LED Color
White
Orange
22
Driver
G-Menu
Welcome to “G
-
Menu” software by AOC. G
-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide. The software Supported operating systems: Windows 10, Windows 8, Windows 7.
Note:
Features are not available for all models.
23
e-Saver
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or
Screen Saver); the actual shutdown time depends on your preferences (see example below).
Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation.
Under each of the four PC statuses, you may choose the desired time (in minutes) from the pull-down menu for your monitor to automatically shutdown. The example below illustrated:
1) The monitor will never shutdown when the PC is powered on.
2) The monitor will automatically shutdown 5 minutes after the PC is powered off.
3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.
4) The monitor will automatically shutdown 20 minutes after the screen saver appears.
You can click “RESET” to set the e
-Saver to its default settings like below.
24
Screen+
Welcome to "Screen+" software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier.
Please follow the installation software to install it.
25
Troubleshoot
Problem & Question Possible Solutions
Power LED Is Not ON
No images on the screen
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.
Is the power cord connected properly?
Check the power cord connection and power supply.
Is the cable connected correctly?
(Connected using the D-sub cable)
Check the DB-15 cable connection.
(Connected using the DVI cable)
Check the DVI cable connection.
(Connected using the HDMI cable)
Check the HDMI cable connection.
(Connected using the DP cable)
Check the DP cable connection.
* DVI/HDMI/DP input is not available on every model.
If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the
Service Center or your dealer.
Can you see "Input Not Supported" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the monitor can handle properly.
Make sure the AOC Monitor Drivers are installed.
Adjust the Contrast and Brightness Controls.
Press to auto adjust.
Picture Is Fuzzy & Has
Ghosting Shadowing Problem
Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back.
Picture Bounces, Flickers Or
Wave Pattern Appears In The
Picture
Move electrical devices that may cause electrical interference as far away from the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution you are using.
26
Monitor Is Stuck In Active
Off-Mode"
The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly fitted in its slot.
Make sure the monitor's video cable is properly connected to the computer.
Inspect the monitor's video cable and make sure no pin is bent.
Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED, GREEN, or
BLUE)
Screen image is not centered or sized properly
Picture has color defects
(white does not look white)
Inspect the monitor's video cable and make sure that no pin is damaged.
Make sure the monitor's video cable is properly connected to the computer.
Adjust H-Position and V-Position or press hot-key (AUTO).
Adjust RGB color or select desired color temperature.
Horizontal or vertical disturbances on the screen
Use Windows7/8/10 shut-down mode to adjust CLOCK and PHASE.
Press to auto-adjust.
27
Specification
General Specification
Panel
Others
Physical
Characteristics
Environmental
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Max resolution
24G2/24G2U
TFT Color LCD
60.5 cm diagonal
0.2745(H)mm x 0.2745(V)mm
R, G, B Analog Interface & HDMI Interface & DP Interface
H/V TTL
Horizontal scan range
Horizontal scan
Size(Maximum)
30~160KHz
527.04mm
Vertical scan range 48-144Hz
Vertical scan Size(Maximum) 296.46mm
Optimal preset resolution 1920x1080@60Hz
1920x1080@60Hz(D-SUB)
1920x1080@144Hz(HDMI 、 DP)
Plug & Play
Power Source
VESA DDC2B/CI
100-240V ～ ,50/60Hz
Power Consumption
Connector Type
Signal Cable Type
Temperature:
Humidity:
Altitude:
Typical (Brightness = 90,Contrast = 50)
(Brightness = 100,Contrast = 100)
Power saving
21W
≤
30W
≤0.
3W
D-Sub/ HDMI/DP/Earphone out/ Line in(24G2U )/USB(24G2U )
Detachable
Operating
Non-Operating
0° to 40°C
-25° to 55°C
Operating
Non-Operating
Operating
Non-Operating
10% to 85% (non-condensing)
5% to 93% (non-condensing)
0~ 5000m(0~ 16404 ft)
0~ 12192m (0~ 40000 ft )
28
Panel
Others
Physical
Characteristics
Environmental
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Horizontal scan range
Horizontal scan
Size(Maximum)
27G2/27G2U
TFT Color LCD
68.6 cm diagonal
0.3114(H)mm x 0.3114(V)mm
R, G, B Analog Interface & HDMI Interface & DP Interface
H/V TTL
30~160KHz
597.888mm
Vertical scan range 48-144Hz
Vertical scan Size(Maximum) 336.312mm
Optimal preset resolution
Max resolution
1920x1080@60Hz
1920x1080@60Hz(D-SUB)
1920x1080@144Hz(HDMI 、 DP)
Plug & Play
Power Source
Power Consumption
Connector Type
Signal Cable Type
Temperature:
Humidity:
Altitude:
VESA DDC2B/CI
100-240V ～ ,50/60Hz
Typical (Brightness = 90,Contrast = 50)
Max.(Brightness = 100,Contrast = 100)
Power saving
28W
≤
36W
≤0.
3W
D-Sub/ HDMI/DP/Earphone out/ Line in (24G2U/27G2U )
/USB(24G2U/27G2U )
Detachable
Operating 0° to 40°C
Non-Operating
Operating
Non-Operating
Operating
Non-Operating
-25° to 55°C
10% to 85% (non-condensing)
5% to 93% (non-condensing)
0~ 5000m(0~ 16404 ft)
0~ 12192m (0~ 40000 ft )
29
Preset Display Modes
Standard
VGA
VGA
VGA
VGA
VGA
VGA
DOS MODE
DOS MODE
SD
SVGA
SVGA
SVGA
XGA
WXGA+
SXGA
SXGA
HD
HD
HD
Full HD
Full HD
Full HD
Full HD
SVGA
SVGA
SVGA
SVGA
XGA
XGA
XGA
XGA
Resolution
640x480@60Hz
640x480@67Hz
640x480@72Hz
640x480@75Hz
640x480@100Hz
640x480@120Hz
720x400@70Hz
720x480@60Hz
720x576@50Hz
800x600@56Hz
800x600@60Hz
800x600@72Hz
800x600@75Hz
800x600@100Hz
800x600@120Hz
832x624@75Hz
1024x768@60Hz
1024x768@70Hz
1024x768@75Hz
1024x768@100Hz
1024x768@120Hz
1440x900@60Hz
1280x1024@60Hz
1280x1024@75Hz
1280x720@50HZ
1280x720@60HZ
1280x1080@60Hz
1920x1080@60Hz
1920x1080@100Hz
1920x1080@120Hz
1920×1080@144Hz
H. Frequency (kHz) V. Frequency (Hz)
31.469
35
37.861
37.5
51.08
61.91
31.469
29.855
31.25
35.156
37.879
48.077
97.551
55.935
63.981
79.975
37.071
45
67.173
67.5
113.21
137.26
158.1
46.875
63.684
76.302
49.725
48.363
56.476
60.023
81.577
59.94
66.667
72.809
75
99.769
119.518
70.087
59.710
50
56.25
60.317
72.188
119.989
59.887
60.02
75.025
49.827
60
59.976
60
99.93
119.982
144
75
99.662
119.97
74.551
60.004
70.069
75.029
99.972
30
Pin Assignments
15-Pin Color Display Signal Cable
Pin No.
1
2
3
4
5
6
7
8
Signal Name
Video-Red
Video-Green
Video-Blue
N.C.
Detect Cable
GND-R
GND-G
GND-B
19-Pin Color Display Signal Cable
Pin No. Signal Name
1
2
TMDS Data 2+
TMDS Data 2 Shield
3
4
5
6
7
8
9
TMDS Data 2
TMDS Data 1+
TMDS Data 1Shield
TMDS Data 1
TMDS Data 0+
TMDS Data 0 Shield
TMDS Data 0
10 TMDS Clock +
31
Pin No.
9
10
11
12
13
14
15
Signal Name
+5V
Ground
N.C.
DDC-Serial data
H-sync
V-sync
DDC-Serial clock
Pin No.
11
12
13
14
15
16
17
18
19
Signal Name
TMDS Clock Shield
TMDS Clock
CEC
Reserved (N.C. on device
SCL
SDA
DDC/CEC Ground
+5V Power
Hot Plug Detect
20-Pin Color Display Signal Cable
Pin No. Signal Name
1
2
3
4
ML Lane 3(n)
GND
ML Lane 3(p)
ML Lane 2(n)
5
6
7
8
9
10
GND
ML Lane 2(p)
ML Lane 1(n)
GND
ML Lane 1(p)
ML Lane 0(n)
Pin No.
11
12
13
14
15
16
17
18
19
20
Signal Name
GND
ML Lane 0(p)
CONFIG1
CONFIG2
AUX CH(p)
GND
AUX CH(n)
Hot Plug Detect
Return OP PWR
DP PWR
32
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
33
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Gaming 61 cm (24") LCD IPS
- Full HD 1920 x 1080 pixels 16:9
- 144 Hz 4 ms 250 cd/m²
- AMD FreeSync Flicker-free technology
- E 18 kWh 21 W
Related manuals
Frequently Answers and Questions
What types of cables does the AOC 24G2 come with?
How should I clean my AOC 24G2 monitor?
What is the recommended ventilation space around the monitor?
What should I do if my AOC 24G2 monitor is emitting a strange smell, sound, or smoke?
Can I use the AOC 24G2 monitor in severe vibration or high impact conditions?
advertisement