EN
Installation instructions
KEUCO GmbH & Co. KG
Oesestr. 36
D-58675 Hemer
Telefon +49 2372 90 4-0
Telefax +49 2372 90 42 36
[email protected]
www.keuco.de
UNIVERSE
Model 12703
311341
07.2016
GB
IMPORTANT - Read this information before carrying out the installation work!
Key to symbols
Attention! Important note warning about the risk of bodily injury or damage to property.
Attention! Important note warning about the risk of electric shock.
Note, tip or reference
ON/OFF switch
Optional
Electric light
Correct installation
Easy to move
Incorrect installation
Difficult to move
Warranty
- The function, safety and integrity of the product are only guaranteed if the instructions given in this manual are adhered to.
Non-observance of the safety instructions could lead to bodily injury and damage to property.
The manufacturer is not liable for damage resulting from non-observance of the instructions.
- To avoid installation errors and damage to the product, it is essential that the installation instructions are followed carefully.
- Besides the information given in this manual, please follow the relevant general safety and accident prevention regulations!
- This product left our factory in a condition complying with all the requirements of technical safety.
- Bulbs are excluded from the scope of the warranty.
General safety instructions and information
- The relevant national regulations and standards must be observed.
- The installation of our product should only by carried out by a qualified domestic installer.
- KEUCO strongly recommends that all its bathroom cabinets containing a 230 V supply should be protected by an
RCD switch with a 30 mA protected circuit. Our shaver supply unit complies with BS/EN 61558.
- Before commencing any cabling work, check that the cables are at zero voltage. Measures must be taken to ensure
that the cables remain dead for the duration of the work (e.g. prevent the power supply from being switched back on).
- The security strips on the product must remain in place until the wall mounting procedure is completed.
- The underlying structure must be suitable for bearing the weight involved.
- The user must determine the intended position of the product before the installation work begins.
- The installation of this product will require at least two people.
- Handle this product with the utmost care to avoid damaging it.
Rings and other objects that may damage the product must be removed before starting the installation work.
- Before carrying out any drilling work, ensure that no plumbing or wiring is routed behind the place where you intend to
drill.
- The magnets incorporated in this product may erase data media, or disrupt or destroy electronic and mechanical
components (such as cardiac pacemakers). It is essential that the safety clearances specified are maintained.
- To clean this product, it is essential that you follow the enclosed cleaning and operating instructions.
- All dimensions are given in millimetres (mm). Drawings are not to scale.
- We reserve the right to make technical changes without notice.
2 - 12
3 - 12
1
24x
4 - 12
2
350
700
800
143
~1400
758
aa
a
3
70
5 40
Ø6
1900 - 1950
30
70
5 - 12
4
1.
2.
2.
3.
4.
5.
6 - 12
Ø6
5
6
7
7 - 12
8
1.
2.
9
1.
2.
8 - 12
SW 3
3.
10
2.
3.
SW 3
1.
11
2.
1.
SW 3
3.
2.
9 - 12
12
1
3
2
15
7
14
13
20
19
11
4
8
21
12
5
6
9
10 - 12
12
Model 12703
No.
Quantity
Description
2
2
Shims for suspension rail
1
3
4
5
6
7
8
9
11
12
13
14
15
19
20
21
2
1
2
1
1
4
6
2
2
2
2
2
4
1
1
1
Suspension rail
100 mm
Attachment set (4x screws/fittings)
Shelf support (12x)
klar
Mirrored door left
399 x 700 mm
Mirrored door right
399 x 700 mm
Threaded pin with tappet
M6 x 20 mm
Glass shelf
317,5 x 115 x 4 mm
Chrome-plated handle
60 x 39 x 8 mm
Magnet
Ø 9,5 mm
Rear wall fastening
Mirrored side wall
121 x 698 x 3 mm
Rear wall
340 x 690 x 3 mm
Hinged bearing
Socket
Item No.
222338
300505
303826
405362
406973
406972
308375
306700
406917
310024
405870
310039
310415
222357
308794
Socket frame
308655
Isolating transformer GB
306566
11 - 12
12 - 12
">
