Yaskawa V7C Package Manual

V7 and V74X Drives
Technical Manual
Models: MV and CIMR-V7*
Document Number: TM.V7.01
QUICK REFERENCE – – DRIVE PARAMETERS
PARAMETERS FACTORY USER
SETTING SETTING
n001
1
n002
0
n003
1
n004
2
n005
0
n006
0
n007
0
n008
0
n009
0
n010
0
n011
60
n012
230/460
n013
60
n014
Note 2
n015
Note 2
n016
Note 2
n017
Note 2
n018
0
n019
10.0
n020
n021
n022
n023
0
n024
6.00
n025
0.00
n026
0.00
n027
0.00
n028
0.00
n029
0.00
n030
0.00
n031
0.00
n032
6.00
n033
100
n034
0
n035
0
n036
Note 1
n037
0
n038
8
n039
0
n040
0
n041
10.0
n042
n043
n044
n050
1 (1)
n051
2 (2)
n052
3 (0)
n053
5 (5)
n054
6 (6)
n055
7 (7)
n056
10 (10)
n057
0
n058
1
n059
2
n060
100
PARAMETERS FACTORY USER
SETTING SETTING
n061
0
n062
0.10
n064
0
n065
0
n066
0
n067
1.00
n068
100
n069
0
n070
0.10
n071
100
n072
0
n073
0.10
n074
100
n075
0
n076
0.10
n077
0
n078
0
n079
10
n080
3
n081
0
n082
0
n083
0.00
n084
0.00
n085
0.00
n086
0.00
n089
50
n090
0.5
n091
0.0
n092
0
n093
170
n094
160
n095
0.00
n096
0
n097
0
n098
160
n099
0.1
n100
0
n101
2
n102
150
n103
1.0
n104
Note 2
n105
Note 1
n106
Note 1
n107
Note 1
n108
Note 1
n109
150
n110
Note 1
n111
Note 2
n112
Note 2
n113
0
n115
0
n116
0
n117
0
n118
0
n119
0.1
PARAMETERS FACTORY USER
SETTING SETTING
n120
0.00
n121
0.00
n122
0.00
n123
0.00
n124
0.00
n125
0.00
n126
0.00
n127
0.00
n128
0
n129
1.00
n130
1.0
n131
1.0
n132
0.00
n133
0
n134
100
n135
0.0
n136
0
n137
0
n138
1.0
n139
0
n140
Note 1
n141
50
n142
12
n143
1 (24 ms)
n144
0%
n145
0.5%
n146
0.2%
n149
3072 (30,
720 Hz)
n150
0
n151
0
n152
0
n153
0
n154
2
n155
2
n156
10
n157
0
n158
Note 1
n159
120
n160
16
n161
10
n162
5 (20 ms)
n163
1.0
n164
0
n166
0
n167
0
n168
0
n169
0.0
n173
83 (0.083)
n174
25 (100 ms)
n175
0
n176
rdy
n177
0
n178
N/A
n179
0024
N/A
Note 1: Factory setting differs depending on the Drive capacity. See Appendix 3-1.
Note 2: Factory setting differs depending on control method selected (n002). See Appendix 3-1.
CONTENTS
PARAGRAPH
SUBJECT
PAGE
QUICK REFERENCE FOR DRIVE PARAMETERS ....................Inside Cover
WARNINGS & CAUTIONS ................................................................... iii
DRIVE SIMPLIFIED STARTUP PROCEDURE...................................... v
CURRENT RATINGS AND HORSEPOWER RANGE.......................... xv
1
1.1
1.2
1.3
1.4
RECEIVING / INSTALLATION ............................................................
General ................................................................................................
Receiving .............................................................................................
Physical Installation .............................................................................
Electrical Installation ............................................................................
1-1
1-1
1-1
1-1
1-6
2
2.1
2.2
2.3
INITIAL START-UP ..............................................................................
Pre-Power Checks ...............................................................................
Open Loop Vector Startup ...................................................................
V/f Startup Procedure ..........................................................................
2-1
2-1
2-2
2-6
3
OPERATION AT LOAD ....................................................................... 3-1
4
4.1
4.2
4.3
4.4
DIGITAL OPERATOR ..........................................................................
General ................................................................................................
Digital Operator ....................................................................................
Status Indicator LEDs ..........................................................................
Monitor Displays ..................................................................................
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
5.18
5.19
5.20
PROGRAMMABLE FEATURES ......................................................... 5-1
General ................................................................................................ 5-1
Accel/Decel Time ................................................................................. 5-2
Accel/Decel: S-Curve Characteristics .................................................. 5-3
Auto-Restart ......................................................................................... 5-4
Carrier Frequency ................................................................................ 5-5
Critical Frequency Rejection ................................................................ 5-6
DC Injection Braking ............................................................................ 5-7
Frequency Reference Bias/Gain (Analog) ........................................... 5-8
Frequency Reference Upper and Lower Limits ................................... 5-9
Frequency Reference Retention .......................................................... 5-9
Frequency Reference Selection ......................................................... 5-10
Jog Reference .................................................................................... 5-13
Local/Remote Reference and Sequence Selection ............................ 5-14
Modbus Control .................................................................................. 5-16
Miscellaneous Protective Functions ................................................... 5-20
Momentary Power Loss Ride-Thru ..................................................... 5-20
Multi-Function Analog Monitor Output (Term. AM and AC) ................ 5-20
Multi-Function Input Terminals (Term. S1-S7) .................................... 5-22
Multi-Function Output Terminals (Term. MA, MB, MC, P1, P2, PC) ... 5-28
Overtorque Detection ......................................................................... 5-31
-i-
4-1
4-1
4-1
4-3
4-3
CONTENTS – Continued
PARAGRAPH
PAGE
SUBJECT
5.21
5.22
5.23
5.24
5.25
5.26
5.27
5.28
5.29
5.30
5.31
5.32
5.33
5.34
Reset Codes: 2-Wire, 3-Wire Initialization ..........................................
Slip Compensation .............................................................................
Stall Prevention ...................................................................................
Stopping Method ................................................................................
Thermal Overload Protection ..............................................................
Torque Compensation .........................................................................
V/f Pattern ...........................................................................................
PID Control .........................................................................................
Copy Function .....................................................................................
Digital Operator Display Selection ......................................................
Energy Saving Control ........................................................................
Multi-Function Analog Input Selection ................................................
Frequency Reference Loss Detection .................................................
Undertorque Detection .......................................................................
6
6.1
6.2
FAULT DIAGNOSIS AND CORRECTIVE ACTIONS ........................... 6-1
General ................................................................................................. 6-1
Displaying Fault Sequence ................................................................... 6-8
Appendix 1
PARAMETER LISTING ....................................................................... A1-1
Appendix 2
SPECIFICATIONS .............................................................................. A2-1
Appendix 3
CAPACITY AND CONTROL METHOD RELATED
PARAMETERS ................................................................................... A3-1
Appendix 4
PERIPHERAL DEVICES .................................................................... A4-1
Appendix 5
DRIVE DIMENSIONS ......................................................................... A5-1
NEMA 1 ............................................................................................... A5-1
NEMA 4x/12 ........................................................................................ A5-4
Appendix 6
DYNAMIC BRAKING OPTION .......................................................... A6-1
Appendix 7
NAMEPLATE INFORMATION ........................................................... A7-1
Appendix 8
REMOVE/INSTALL DRIVE FACE PLATES ....................................... A8-1
NEMA 1 .............................................................................................. A8-1
NEMA 4x/12 ....................................................................................... A8-3
Index
.............................................................................................................. I-1
- ii -
5-32
5-33
5-34
5-35
5-36
5-37
5-38
5-42
5-46
5-52
5-53
5-55
5-57
5-58
WARNINGS, CAUTIONS, INSTRUCTIONS
WARNING
YASKAWA manufactures component parts that can be used in a wide variety of industrial
applications. The selection and application of YASKAWA products remain the responsibility of
the equipment designer or end user. YASKAWA accepts no responsibility for the way its products are incorporated into the final system design. Under no circumstances should any
YASKAWA product be incorporated into any product or design as the exclusive or sole safety
control. Without exception, all controls should be designed to detect faults dynamically and
fail safely under all circumstances. All products designed to incorporate a component part
manufactured by YASKAWA must be supplied to the end user with appropriate warnings and
instructions as to that part’s safe use and operation. Any warnings provided by YASKAWA
must be promptly provided to the end user. YASKAWA offers an express warranty only as to
the quality of its products in conforming to standards and specifications published in the
YASKAWA manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS OFFERED.
YASKAWA assumes no liability for any personal injury, property damage, losses, or claims
arising from misapplication of its products.
WARNING
• Do not connect or disconnect wiring while the power is on. Do not remove covers or
touch circuit boards while the power is on.
• Before servicing, disconnect all power to the equipment. The internal capacitor
remains charged even after the power supply is turned OFF. Status indicator LEDs
and Digital Operator display will be extinguished when the DC bus voltage is below
50 VDC. To prevent electric shock, wait at least 1 minute after all indicators are
OFF.
• Do not perform a withstand voltage test on any part of the unit. This equipment
uses sensitive devices and may be damaged by high voltage.
• The drive is not suitable for circuits capable of delivering more than 18000 RMS
symmetrical amperes at 250V maximum or 480V maximum. Install adequate
branch short circuit protection. Refer to appendix. Failure to do so may result in
equipment damage and/or personal injury.
WARNING
• Input Fuses are required for proper branch short circuit protection for all NEMA
type 4X/12 drives. Failure to use recommended fuses (See Appendix 4) may result
in damage to the drive and/or personal injury.
- iii -
CAUTION
The Drive leaves the factory with parameters initialized for 2-Wire control (when
using external Run/Stop signals). Before using the initialization function of constant
n001, know your control wiring configuration:
10 = Factory 2-Wire Control Initialization (Maintained RUN Contact)
11 = Factory 3-Wire Control Initialization (Momentary START/STOP Contact)
Entering either Initialization code resets all parameters to factory settings, and
automatically returns parameter n001 setting to “ 1 ”. If the Drive is connected for
3-Wire control and this parameter is set to “ 10 ” (2-Wire Control Initialization), the
motor may run in reverse direction WITHOUT A RUN COMMAND APPLIED.
Equipment damage or personal injury may result.
Parameter n012 must be set to proper motor voltage.
Always ground the Drive using the ground terminal provided.
Never connect main circuit output terminals T1 (U), T2 (V) & T3 (W) to AC main circuit power supply.
When programmed for auto-restart ( n082 = " 1 " thru " 10 "), the motor may restart
unexpectedly — personal injury may result
For Enclosed wall-mounted type (NEMA type 1)
When mounting units in an enclosure, remove the top, bottom and terminal covers. Install
a cooling fan or some other means to maintain the air entering the enclosure below 113°F
(45°C).
For Water and dust tight type (NEMA type 4X/12)
Never submerge this model in water. For the cable lead-in section, use a waterproof cable
gland. After completion of wiring, mount the front cover and bottom cover with care so as
not to damage the gasket. The front cover mounting screws and bottom cover mounting
screws are made of stainless. Replacements must be of stainless steel and the same
length.
IMPORTANT
• Wiring should be performed only by qualified personnel.
• Verify that the rated voltage of the drive matches the voltage of the incoming power.
• Some drawings in this manual are shown with the protective covers and shields removed, in order to
describe detail with more clarity. Make sure all covers and shields are replaced before operating this
product.
• This manual may be modified when necessary because of product improvement, modification, or
changes in specifications.
• YASKAWA is not responsible for any modification of the product made by the user, doing so will void
the warranty.
- iv -
SIMPLIFIED STARTUP PROCEDURE
This procedure is a simplified step by step guide to installing, programming, and using the
Yaskawa V7 & V74X (hereafter referred to as the Drive). It highlights several common installation
configurations. Detailed information on all drive features can be found in Technical Manual.
❏ Check Nameplate - Be certain your input voltage source, motor and drive nameplates are all
marked either 230V or 460V. Other voltages can be used, but require additional programming; see
paragraph 5.27, V/f pattern.
❏ Mount drive - on a vertical surface with adequate space for air circulation (4.7" above and below,
1.2" on each side).
❏ Remove front cover - fit conduit to bottom plate, and connect power and ground wires as shown.
CAUTION
BE CERTAIN YOU CONNECT INPUT POWER TO TERMINALS L1, L2, AND L3
ONLY, OR SERIOUS DAMAGE WILL RESULT. CONNECT MOTOR TO TERMINALS
T1, T2, AND T3 ONLY.
POWER WIRING SCHEMATIC
–
+1
+2
R/L1 S/L2 T/L3
Note:
Exact terminal configuration
may vary with drive rating
B1
B2
U/T1 V/T2 W/T3
3 PHASE
INPUT
POWER
MOTOR
WIRE TO
EARTH GROUND
❏ Replace cover and apply input power – digital operator shows “0.00”; The FREF LED
is on and the RUN LED is flashing. Press the DSPL key until the LO/RE LED is on.
Press the UP ARROW button until the display shows “Lo,” then press the DSPL button until the
FREF LED is on. Rotate the potentiometer on the front of the digital operator until the display
shows “6.00.” Press the RUN button and note the direction of motor rotation. If rotation is incorrect,
remove power, wait for the display lights to go out, then switch wires between terminals T1 and T2.
Replace the front cover and apply input power.
-v-
❏ Digital Operator
The DSPL button cycles through all of the quick start LEDs.
To access a parameter, press the DSPL button until the
PRGM LED is on. Use the UP and DOWN keys until the
desired parameter number is displayed, then press
ENTER. Use the UP and DOWN keys to adjust the value
then press ENTER then DSPL.
0.00
FREF
FOUT
IOUT
MNTR
LO/RE PRGM
F/R
DSPL
RUN
DATA
STOP
RESET
MIN
MAX
ENTER
Before the drive will accept a RUN command, one of the
following LEDs must be on: FREF, FOUT, IOUT, MNTR, or F/R. For more specific
information on the digital operator, see Section 4.
❏ Choose a configuration from Table 1 below. Each example listed below contains a
control wiring diagram, operation explanation, and all necessary programming. The
Drive can be controlled in many more ways than is described in these examples, see
Paragraph 5.11, Frequency Reference Selection, and Paragraph 5.13, Local/Remote
Reference and Sequence Selection.
Table 1: Drive Configuration Examples
Sequence*
Source
(Run / Stop)
Digital Operator
Reference*
Source
(Motor Speed)
Digital Operator
2-wire
Digital Operator
3-wire
Digital Operator
2-wire
4-20 mA
3-wire
Remote Speed
Potentiometer
0 – 10V DC
with several
digital presets
2-wire
Description
Example
This method requires no control wiring connections to the
drive. It is most often used during startup of the drive.
With this method, the drive can be started and stopped
using an external (remote) signal.
This method is the same as Example 2 above, but uses
pushbuttons instead.
This method is the same as Example 2, but the reference
comes from a remote 4 – 20 mA source such as a PLC.
This method is similar to Example 3, but utilizes a remote
mounted speed control (potentiometer).
This method is similar to 2, but allows switching between
an analog reference and three digital preset references.
Example 1
Example 2
Example 3
Example 4
Example 5
Example 6
* For a more detailed explanation of sequence and reference, consult the Definitions Section.
❏ Control Terminal Wiring – Remove power and
Control Terminals
2
OFF
SW2(2)
1
wait for all LEDs to go out before making control
terminal connections. Control wiring should be
sized 16 to 20 AWG. Control wiring should be
shielded, with the shield wire connected to the
ground terminal, which is located towards the
left side of the aluminum heat sink.
S5 S6 S7 P1 P2 R+ R- FS FR FC
MA MB MC
S1 S2 S3 S4 SC PC S+ S- AM AC RP
❏ Control Method – This document assumes that the drive will be left in the volts per
hertz (V/f) control method. For a further explanation of control method or to change the
control method, consult Section 2.1.
- vi -
Example 1: Sequence & Reference Are Local (Digital Operator)
S1
Control Wiring Schematic
S2
FS
S3
FR
FC
FREF
FOUT
F/R
IOUT
MNTR
LO/RE PRGM
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
MAX
S5
S6
S7
SC
No Control Wiring Necessary
When the drive is set up with the sequence and the reference coming from the digital operator, it is in “Local”
control. Local control is often used during startup to verify motor operation, rotation, etc. The drive can be temporarily placed in “Local” control simply by using the LO/RE quick start LED. If power is removed and then
restored, the drive will come up in the “Remote” mode.
The drive can be programmed so that even if power is lost, the drive will come up in the local mode (see Table
2 below).
OPERATION:
•
The frequency reference comes from the digital operator pot.
•
The drive can be started by pressing the RUN key on the digital operator.
•
The drive can be stopped by pressing the STOP key on the digital operator.
•
The direction of the motor can be changed regardless of motor speed by using F/R quick start LED.
Table 2: Programming required for “Local” mode
Parameter
n001
n003
n004
Display
4
0
0
n036
Set Motor F.L.A.
Quick Start
LED
F/R
Description
Changing this parameter will allow access to all parameters.
This parameter sets the sequence (start/stop) to "Local" mode.
This parameter sets the reference (motor speed) to come from the
digital operator potentiometer (local).
Enter the motor’s full load amps (as shown on the motor
nameplate).
Motor direction can be changed regardless of motor speed using
this quick start LED.
- vii -
Example 2: Remote Sequence (2-Wire) & Local Reference (Digital
Operator)
(K1)
S1
Forward Run
FWD
Control Wiring Schematic
0.00
FC
Reverse Run
REV
FS
FR
(K2)
S2
FREF
FOUT
IOUT
S3
MNTR
LO/RE PRGM
F/R
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
MAX
S5
S6
S7
Shield (Drain Wire)
To Terminal
SC
This configuration is used when the sequence comes from a remote source, such as a relay or a PLC. It can
also be used with a maintained switch when it is desirable to have the drive restart on restoration of power. It
should not be used where safety of attending personnel might be threatened by a restart.
OPERATION:
•
The frequency reference comes from the digital operator pot.
•
Close (K1) to Run Forward at frequency set by the digital operator pot.
•
Close (K2) to Run Reverse at frequency set by the digital operator pot.
•
If both (K1) & (K2) are closed, the drive stops and displays the error message: “EF”
•
If the drive is put in the “Local” mode using the LO/RE quick start LED, the drive will behave the same as
illustrated in Example 1.
Table 3: Programming Required For Remote 2-wire Sequence & Local Reference
Parameter
Display
n001
10
n001
4
n004
0
n036
Set Motor FLA
Description
The drive will perform a 2-wire reset.
CAUTION
Setting this value will reset all parameters to their original factory
settings (all previous adjustments will be lost) When the drive
completes the reset, this parameter returns to a value of 1.
After doing the reset above, the password parameter returned to a
1. Change it to a 4 to get access to all parameters in the drive.
This parameter sets the reference (motor speed) to come from the
digital operator potentiometer (local).
Enter the motor’s full load amps (as shown on the motor
nameplate).
- viii -
Example 3: Remote Sequence (3-Wire) & Local Reference (Digital
Operator)
(PB1)
Start
S1
START
Control Wiring Schematic
STOP
FS
(PB2)
S2
0.00
(SW1) Forward
S3
Reverse
FOR/REV
FR
FC
FREF
FOUT
F/R
IOUT
Stop
MNTR
LO/RE PRGM
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
MAX
S5
Shield (Drain Wire)
To Terminal
S6
S7
SC
This configuration is best when a person rather than an external controller (PLC, relay, etc.) controls the drive.
OPERATION:
•
The frequency reference comes from the digital operator pot.
•
Close pushbutton (PB1) momentarily while pushbutton (PB2) is closed, and the drive will run at the
frequency setting in U1-01. Pushbutton (PB1) does NOT need to be maintained.
•
Open pushbutton (PB2) at any time and the drive will stop.
•
If switch (SW1) is open, the drive will run in the forward direction. If switch (SW1) is closed, the drive will
run in the reverse direction. Switch (SW1) can be operated with the drive running at any speed.
•
If the drive is put in the “Local” mode using the LO/RE quick start LED, the drive will behave the same as
illustrated in Example 1.
Table 4: Programming Required For Remote 3-wire Sequence & Local Reference
Parameter
Display
n001
11
n001
4
n004
0
n036
Set Motor FLA
Description
The drive will perform a 3-wire reset.
CAUTION
Setting this value will reset all parameters to their original factory
settings (all previous adjustments will be lost). When the drive
completes the reset, this parameter returns to a value of 1.
After doing the reset above, the password parameter returned to a
1. Change it to a 4 to get access to all parameters in the drive.
This parameter sets the reference (motor speed) to come from the
digital operator potentiometer (local).
Enter the motor’s full load amps (as shown on the motor
nameplate).
- ix -
Example 4: Remote Sequence (2-Wire) & Remote Reference
(4 – 20 mA)
(K1)
S1
Forward Run
FWD
Control Wiring Schematic
(K2)
S2
FS
0.00
(+)
FR
External
4-20 mA
Source
4-20 mA
FREQ. REF
FC
(–)
ANALOG
COMMON
Reverse Run
REV
FREF
FOUT
F/R
IOUT
S3
MNTR
LO/RE PRGM
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
MAX
S5
S6
Shield
(Drain Wire)
S7
Shield (Drain Wire)
To Terminal
SC
This configuration is used when the start & stop signals and the frequency reference come from a remote
source, such as a PLC. It can also be used with a maintained switch when it is desirable to have the drive
restart on restoration of power. It should not be used where safety of attending personnel might be threatened
by a restart.
OPERATION:
• Close (K1) to Run Forward.
• Close (K2) to Run Reverse.
• If both (K1) & (K2) are closed, the drive stops and displays the error message: “EF.”
• Frequency reference is proportional to the signal level at Terminal FI. 4mA = 0 Hz, 12mA = 30 Hz, &
20mA = 60 Hz.
• If the drive is put in the “Local” mode using the LO/RE quick start LED, the drive will behave the same as
illustrated in Example 1.
Table 5: Programming Required For Remote 2-wire Sequence & Remote (4-20 mA) Reference
Parameter
Display
n001
10
n001
4
n004
3
n036
Set Motor FLA
Description
The drive will perform a 2-wire reset.
CAUTION
Setting this value will reset all parameters to their original factory
settings (all previous adjustments will be lost). When the drive
completes the reset, this parameter returns to a value of 1.
After doing the reset above, the password parameter returned to a
1. Change it to a 4 to get access to all parameters in the drive.
This parameter sets terminal FR to be a 4-20mA input. NOTE:
Switch SW2 (2) must be closed (“on”). See page 2 for SW2(2)
location.
Enter the motor’s full load amps as shown on the motor nameplate.
-x-
Example 5: Remote Sequence (3-Wire) & Speed Potentiometer
(PB1)
START
Control Wiring Schematic
S2
STOP
FS
2.5K
0.00
+12 VDC
S3
FOR/REV
FREF
FR
FREQUENCY
REFERENCE
0 - 10V DC
2.5K
Speed Pot
(R1)
Start
S1
Optional
Trim Pot
(R2)
FC
ANALOG
COMMON
FOUT
F/R
IOUT
(PB2)
Stop
(SW1) Forward
Reverse
MNTR
LO/RE PRGM
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
MAX
S5
Shield (Drain Wire)
To Terminal
S6
S7
SC
This configuration is best when a person rather than an external controller (PLC, relay, etc.) controls the drive.
Both potentiometers ((R1) & (R2)) should have a resistance value between 2000Ω and 3000Ω and be rated for
at least 1 Watt. The trim pot is optional, but without it the manual speed pot will output 10V (60 Hz) at just
three-quarters of its rotation.
OPERATION:
• Close pushbutton (PB1) momentarily while pushbutton (PB2) is closed and the drive will start.
Pushbutton (PB1) does NOT need to be maintained.
• Open pushbutton (PB2) at any time and the drive will stop.
• If switch (SW1) is open the drive will run in the forward direction. If switch (SW1) is closed, the drive will
run in the reverse direction. Switch (SW1) can be operated with the drive running at any speed.
• Frequency reference is proportional to the signal level at Terminal FV.
0V = 0 Hz, 5V = 30 Hz, & 10V = 60 Hz.
• If the drive is put in the “Local” mode using the LO/RE quick start LED, the drive will behave the same as
illustrated in Example 1.
Table 6: Programming Required For Remote 3-wire Sequence & Speed Pot Reference
Parameter
Display
n001
11
n001
4
n036
Set Motor FLA
Description
The drive will perform a 3-wire reset.
CAUTION
Setting this value will reset all parameters to their original factory
settings (all previous adjustments will be lost). When the drive
completes the reset, this parameter returns to a value of 1.
After doing the reset above, the password parameter returned to a
1. Change it to a 4 to get access to all parameters in the drive.
Enter the motor’s full load amps as shown on the motor nameplate.
After the programming is complete, the trim pot needs to be calibrated. Press DSPL until the FREF quick start
LED is illuminated. Turn the Speed Pot (R1) all the way up. Adjust the trim pot (R2) so that the “Frequency
Reference” display is just flickering between 59.99 Hz and 60.00 Hz. This completes the trim pot calibration.
- xi -
Example 6: Remote Sequence (2-Wire) & Remote Reference
(0 – 10 VDC) and three digital preset speeds
(K1)
S1
Forward Run
FWD
Control Wiring Schematic
0.00
FREF
FR
External
0 - 10 VDC
Source
0 - 10V
FREQ. REF
FC
(–)
Reverse Run
REV
FS
(+)
(K2)
S2
ANALOG
COMMON
FOUT
F/R
IOUT
S3
MNTR
LO/RE PRGM
Shield (Drain Wire)
To Terminal
S4
DSPL
RUN
DATA
ENTER
STOP
RESET
MIN
(SW1)
MAX
S5
MULT
STEP 1
(SW2)
S6
Shield
(Drain Wire)
MULT STEP 2
S7
SC
OPERATION:
• Close (K1) to Run Forward.
• Close (K2) to Run Reverse.
• If both (K1) & (K2) are closed, the drive stops and displays the error message: “EF.”
• Frequency reference is determined by the status of the switches (SW1) and (SW2).
• If the drive is put in the “Local” mode using the LO/RE quick start LED, the drive will behave the same as
illustrated in Example 1.
(SW1) Status
Open
Closed
Open
Closed
(SW2) Status
Open
Open
Closed
Closed
Reference Source
Analog value on terminal FR
Digital value stored in parameter n025
Digital value stored in parameter n026
Digital value stored in parameter n027
Table 7: Programming Required For Remote 2-wire Sequence & Multiple References
Parameter
Display
n001
10
n001
4
n025
User Set
n026
User Set
n027
User Set
n036
Set Motor FLA
Description
The drive will perform a 2-wire reset.
CAUTION
Setting this value will reset all parameters to their original factory
settings (all previous adjustments will be lost). When the drive
completes the reset, this parameter returns to a value of 1.
After doing the reset above, the password parameter returned to a
1. Change it to a 4 to get access to all parameters in the drive.
Sets the frequency reference when switch (SW1) is closed and
switch (SW2) is open.
Sets the frequency reference when switch (SW1) is open and switch
(SW2) is closed.
Sets the frequency reference when switches (SW1) and (SW2) are
closed.
Enter the motor’s full load amps as shown on motor nameplate.
- xii -
Definitions
Sequence – refers to how the drive is started, stopped, and told which direction to run.
When the sequence comes from the digital operator (local), the drive is started and stopped
using the “RUN” and “STOP” keys on the digital operator, and direction is given via the
“FWD/REV” key. Sequence can also come from the drive’s control terminals (remote)
using either two-wire or three-wire control. The sequence inputs to the drive do NOT require
any outside voltages to activate them. Instead, contact closures (either from switches, relay
contacts or open collector circuits) activate the sequence inputs. Other sequence sources are
available; consult Paragraph 5.13, Local/Remote Reference and Sequence Selection for details.
Two-wire sequence – utilizes a “maintained” switch or relay contact. It is used on applications where it is desirable to have the drive restart on restoration of power. It
should not be used where safety of attending personnel might be threatened by a
restart. This method is generally restricted to unattended fans & pumps, or where
another controller is entrusted with the decision to restart. Direction is controlled by maintaining either a forward run or a reverse run command.
Three-wire sequence – utilizes “momentary” buttons or switches. This control
scheme emulates the traditional 3-wire motor starter control. A momentary closure of
a normally open run switch latches the drive in the RUN
Start
S1
mode (STOP switch must be closed or the drive will not
START
accept the momentary RUN command). A momentary
Stop
S2
opening of the normally closed STOP switch unlatches
STOP
RUN mode bringing the drive to a stop. The three-wire
sequence is used where it would be dangerous for the
SC
drive to restart after a power outage. This method
requires an intentional restart, as the RUN command is
3-Wire Sequence
unlatched immediately on loss of power. Direction is
determined by another maintained contact closure (closed = reverse).
Reference – The frequency reference tells the drive how fast to run the motor. There are several
source options for the frequency reference. First, the frequency reference can come from the
digital operator (local). Simply put, the motor speed can be entered into the keypad. Second, the
frequency reference can come from an analog signal (remote), such as 0 to 10 Volts DC. When
0 Volts is applied to the drive, the drive will run at zero speed. When 10V is applied to the drive,
it will run at full speed. Apply anything in between and the drive will run at that corresponding
frequency (2.5VDC = 25% speed = 15 Hz). Other reference sources are available; consult
Paragraph 5.11, Frequency Reference Selection for details.
Local Control – when the sequence and/or reference comes from the digital operator.
Remote Control – when the sequence and/or reference comes from the control terminals.
- xiii -
- xiv -
Intentionally Left Blank
Current Ratings & Horsepower Range
Rated
Input Voltage
230V
460V
(1)
Current
Rating [A]
0.8
1.6
3.0
5.0
8.0
11.0
17.5
25.0
33.0
1.2
1.8
3.4
4.8
5.5
8.6
14.8
18.8
21.0(1)
Nominal
Horsepower
1/8
1/4
1/2
3/4 & 1
2
3
5
7.5
10
1/2
3/4
1&2
3
3
5
7.5 & 10
10
15(1)
Model Number
CIMR-V7*
MV
20P1
A001
20P2
A002
20P4
A003
20P7
A005
21P5
A008
22P2
A011
23P7
A017
25P5
A025
27P5
A033
40P2
B001
40P4
B002
40P7
B003
41P5
B005
42P2
–
43P7
B009
45P5
B015
47P5
–
(1)
47P5
–
47P5 drive, with a current rating of 21.0 A and nominal horsepower of 15, is only
available as a V74X drive.
WARNING
Do not touch circuit components until main input power has been turned
OFF. Status indicator LEDs and Digital Operator display will be extinguished
when the DC bus voltage is below 50 VDC. Wait 5 additional minutes.
Do not connect or disconnect wires and connectors while the main input
power is turned on.
CAUTION
The Drive leaves the factory with parameters initialized for 2-Wire control
(when using external Run/Stop signals). Before using the initialization
function of constant n001, know your control wiring configuration:
10 = Factory 2-Wire Control Initialization (Maintained RUN Contact)
11 = Factory 3-Wire Control Initialization (Momentary START/STOP Contact)
Entering either Initialization code resets all parameters to factory settings,
and automatically returns parameter n001 setting to “ 1 ”. If the Drive is
connected for 3-Wire control and this parameter is set to “ 10 ” (2-Wire
Control Initialization), the motor may run in reverse direction WITHOUT A
RUN COMMAND APPLIED. Equipment damage or personal injury may
result.
- xv -
- xvi -
Section 1. RECEIVING AND INSTALLATION
1.1 GENERAL
This document pertains to the V7 ac drive. This manual reflects the Software Version 0028 for
models CIMR-V7▫▫▫0P1 through V7▫▫▫4P0 and Software Version 0106 for models CIMR-V7▫▫▫5P5
and V7▫▫▫7P5. This document is equally applicable to drives identified as GPD315, GPD315/V7,
GPD315/V74X, and V74X. Additionally, in this document, the word “drive”, “ac drive”, and “inverter”
may be used interchangeably. The V7 (NEMA type1) and V74X (NEMA type 4X/12), hereafter
referred to as the "Drive," are general purpose sine-coded pulse width modulated AC motor drives
which generate an adjustable voltage/frequency three phase output for complete speed control of
most conventional squirrel cage induction motors. Automatic stall prevention and voltage boost prevent nuisance tripping during load or line side transient conditions. The Drive will not induce any
voltage line notching distortion back to the utility line, and it maintains a displacement power factor of
not less than 0.98 throughout its speed range.
When properly installed, operated and maintained, the Drive will provide a lifetime of service. It is
mandatory that the person who operates, inspects, or maintains this equipment thoroughly read and
understand this manual before proceeding.
Information in this manual covers both the NEMA type 1 and NEMA type 4X/12 configuration of the
Drive. It also contains basic information for the operator control station. For detailed operation of
other units in the drive system, refer to their respective manuals.
1.2 RECEIVING
The Drive is thoroughly tested at the factory. After unpacking, verify the part numbers on the nameplate with the purchase order (invoice). Any damages or shortages evident when the equipment is
received must be reported immediately to the commercial carrier who transported the equipment.
Assistance, if required, is available from your sales representative.
CAUTION
Do not install a drive that is damaged or missing parts.
If the drive will be stored after receiving, keep it in its original packaging and store according to
storage temperature specifications in Appendix 2.
1.3 PHYSICAL INSTALLATION
Location of the Drive is important to achieve proper performance and normal operating life. The unit
should be installed in an area where it will be protected from:
• Extreme cold and heat. Use only within the ambient temperature range (for open chassis
type): 14 to 122°F (-10 to +50°C)
• Rain, moisture
• Oil sprays, splashes
• Salt spray
• Direct sunlight. (Avoid using outdoors)
• Corrosive gases (e.g. sulfurized gas) or liquids
• Dust or metallic particles in the air
• Physical shock, vibration
• Magnetic noise (Example: welding machines, power devices, etc.)
• High humidity
• Radioactive substances
• Combustibles: thinner, solvents, etc.
When preparing to mount the Drive, lift it by its base, never by the front cover. For effective cooling,
as well as proper maintenance, the Drive must be installed on a flat, non-flammable vertical surface
(wall or panel) using four mounting screws. There MUST be a MINIMUM 3.9 in. clearance above
and below the Drive to allow air flow over the heat sink fins. A minimum 1.2 in. clearance is required
on each side of the Drive.
1-1
1.3 PHYSICAL INSTALLATION
Continued
AIR
3.94 in.
(100mm)
30mm
30mm
AIR
3.94 in.
(100mm)
1. To use 5.5/5.7 kw (7.5/10 Hp) Drives as open chassis, remove both top and bottom covers.
2. The clearances required at top/bottom and both sides are common in open chassis type
(IP00) and enclosed wall-mounted type (IP20).
3. For the external dimensions and mounting dimensions, refer to the “DIMENSIONS” section
of Appendix 5.
4. Allowable intake air temperature to the Drive:
Open chassis type:
-10°C to +50°C
Enclosed wall-mounted type: -10°C to +40°C
5. Allow sufficient space for the sections at the upper and lower parts marked with * in order to
permit the flow of intake/exhaust air to/from the Drive.
1-2
1.3 PHYSICAL INSTALLATION
Continued
For details on removing the front panels and accessing the terminals, see Appendix 8.
Figure 1-1a. Component Identification
1-3
1.3 PHYSICAL INSTALLATION
Continued
Figure 1-1b. Component Identification
1-4
Continued
1.4 PHYSICAL INSTALLATION
Model
Model
CIMR-V7*
20P1
20P2
20P4
20P7
MV
A001
A002
A003
A005
CIMR-V7*
21P5
22P2
40P2
40P4
40P7
41P5
42P2
MV
A008
A011
B001
B002
B003
B005
—
Model
Model
CIMR-V7*
23P7
43P7
MV
A017
B009
CIMR-V7*
25P5
27P5
45P5
47P5
MV
A025
A033
B015
B018
Figure 1-1c. Main Circuit Terminals
1-5
1.4 ELECTRICAL INSTALLATION
The Drive leaves the factory with all parameters set for 2-Wire external reference control. Figure 1-5
must be used for all external connections.
To use the Drive in a 3-Wire application, drive parameters n001, n003, and n004 must be
reprogrammed, using the Digital Operator. Figure 1-6 must then be used for all external connections.
IMPORTANT
When a cable gland is used for water and dust tight type (NEMA type 4X/12) models, observe the
following:
• Use multi-core cable for cable gland. (If more than one cable is inserted into one cable gland,
a gap is created and may cause leakage.)
• Seal the cable gland with a gasket without fail. (A gasket is attached to the recommended
cable gland.)
Cable Gland Mounting Hole
Dimensions in inches (mm)
Model CIMR-V7*
MV
20P1
A001
20P2
20P4
20P7
A002
A003
A005
3-0.89 DIA
(3-Ø 22.6)
21P5
22P2
23P7
A008
A011
A017
3-1.06 DIA
(3-Ø 26.8)
25P5
27P5
A025
A033
3-1.38 DIA
(3-Ø 35)
40P2
40P4
40P7
B001
B002
B003
3-0.89 DIA
(3-Ø 22.6)
41P5
42P2
43P7
B005
–
B009
3-1.06 DIA
(3-Ø 26.8)
45P5
47P5
B015
–
3-1.38 DIA
(3-Ø 35)
Qty-Dia
A. Main Circuit Input /Output Wiring
Complete wire interconnections according to Table 1-2, Figure 1-5 thru Figure 1-7. Be sure to
observe the following:
• Use 600V vinyl-sheathed wire or equivalent. Wire size and type should be determined by local
electrical codes.
• Avoid routing power wiring near equipment sensitive to electrical noise.
• Avoid running input and output wiring in the same conduit.
• NEVER connect AC main power to output terminals T1(U), T2(V), and T3(W).
• NEVER allow wire leads to contact metal surfaces. Short-circuit may result.
• NEVER connect power factor correction capacitors to the drive output. Consult Yaskawa when
connecting noise filters to the drive output.
• WIRE SIZING MUST BE SUITABLE FOR CLASS I CIRCUITS.
• When connecting motor to drive’s output terminals, include a separate ground wire. Attach
ground wire solidly to motor frame and to drive’s ground terminal
.
• When using armored or shielded cable for connection between drive and motor, solidly connect
armor or shield to motor frame, and to drive’s ground terminal
.
• Motor lead length should NOT EXCEED 164 feet (50 meters), and motor wiring should be run in
a separate conduit from the power wiring. If lead length must exceed this distance, reduce carrier
frequency (see paragraph 5.8) and consult factory for proper installation procedures.
• Use UL listed closed loop connectors or CSA certified ring connectors sized for the selected wire
gauge. Install connectors using the correct crimp tool recommended by the connector manufacturer.
1-6
1.4 ELECTRICAL INSTALLATION
Continued
Table 1-1. Wire and Terminal Screw Sizes
230V 3-phase Input
Model
Terminal Symbol
CIMRV7*
Screw
MV
20P1
A001
20P2
A002
20P4
A003
20P7
A005
21P5
A008
22P2
A011
23P7
A017
25P5
A025
27P5
A033
Tightening
Torque
lb • in
(N • m)
7.1 to 8.88
(0.8 to 1.0)
7.1 to 8.88
M3.5
(0.8 to 1.0)
7.1 to 8.88
M3.5
(0.8 to 1.0)
7.1 to 8.88
M3.5
(0.8 to 1.0)
M4 10.65 to 13.31
(1.2 to 1.5)
10.65
to 13.31
M4
(1.2 to 1.5)
M4 10.65 to 13.31
(1.2 to 1.5)
22.19
M5
(2.5)
22.19
M5
(2.5)
M3.5
R/L1, S/L2, T/L3
B1, B2
U/T1, V/T2, W/T3
-, +1,+2
Wire
Applicable
Recommended
size
size
mm2 AWG
mm2 AWG
0.75 to 2 18 to
14
18
to
0.75 to 2
14
0.75 to 2 18 to
10
0.75 to 2 18 to
14
14
to
2 to 5.5
10
2 to 5.5 14 to
10
14
to
2 to 5.5
10
2
14
2
14
2
14
2
14
2
14
3.5
12
5.5
10
5.5 to 8 10 to 8
8
8
5.5 to 8 10 to 8
8
8
Type
600V
vinylsheathed
wire or
equivalent
460V 3-phase Input
Model
Terminal Symbol
CIMRV7*
Screw
MV
40P2
B001
M4
40P4
B002
M4
R/L1, S/L2, T/L3
B1, B2
U/T1, V/T2, W/T3
-, +1,+2
40P7
B003
41P5
B005
42P2
–
43P7
B009
M4
45P5
B015
M4
47P5
—
M5
x1
M4
M4
M4
Tightening
Torque
lb • in
(N • m)
10.65 to 13.31
(1.2 to 1.5)
10.65 to 13.31
(1.2 to 1.5)
10.65 to 13.31
(1.2 to 1.5)
10.65 to 13.31
(1.2 to 1.5)
10.65 to 13.31
(1.2 to 1.5)
10.65 to 13.31
(1.2 to 1.5)
12.43
(1.4)
22.19
(2.5)
Wire
Applicable
Recommended
size
size
mm2 AWG
mm2 AWG
14 to
10
14
to
2 to 5.5
10
2 to 5.5 14 to
10
14
to
2 to 5.5
10
2 to 5.5 14 to
10
2 to 5.5 14 to
10
12
to
3.5 to 5.5
10
5.5 to 8 12 to
10
2 to 5.5
2
14
2
14
2
14
2
14
2
14
2
3.5 x 1
14
12 x 1
5.5
10
5.5
10
Type
600V
vinylsheathed
wire or
equivalent
Note: The wire size is set for copper wires at 160°F (75°C)
Control Circuit
Model
Terminal Symbol
MA, MB, MC
Common
S1 to S7, P1, P2, SC,
to
PC, R+, R-, S+, S-,
all models
FS, FR, FC, AM, AC, RP
Screw
Tightening
Torque
lb • in (N • m)
M3
4.44 to 5.33
(0.5 to 0.6)
M2
Wire
Applicable size
mm2
AWG
twisted wire 0.5 to 1.25 20 to 16
single
0.5 to 1.25 20 to 16
1.94 to 2.21 twisted wire 0.5 to 0.75 20 to 18
(0.22 to 0.25) single
0.5 to 1.25 20 to 16
1-7
Recommended
size
Type
mm2 AWG
0.75
0.75
18
18
Shielded
wire or
equivalent
1.4 ELECTRICAL INSTALLATION
Continued
Table 1-2. Main Circuit Terminal Functions and Voltages
TERMINAL
FUNCTION
VOLTAGE / SIGNAL LEVEL
L1 (R)
L2 (S)
L3 (T)
Main circuit input power supply
230V Drive: 200 / 208 / 220 / 230V at 50/60 Hz
460V Drive: 380 / 400 / 440 / 460 / 480V
at 50/60 Hz
T1 (U)
T2 (V)
T3 (W)
Main circuit output
230V Drive: 0 - 200 / 208 / 220 / 230V
460V Drive: 0 - 400 / 440 / 460 / 480V
B1
B2
For connection of braking resistor (option)
+1
+2
DC Reactor terminals
–
DC Bus terminals (+1 & –)
Ground terminal (100 ohms or less)
––––
1-8
Continued
1.4 ELECTRICAL INSTALLATION
B. Control Circuit
All basic control circuit (signal) interconnections are shown in the appropriate diagram:
• Interconnections for external two-wire control in combination with the Digital Operator are shown in
Figure 1-5.
• Interconnections for external three-wire control in combination with the Digital Operator are shown in
Figure 1-6.
Make wire connections according to Figures 1-5 thru 1-7 and Table 1-3; observe the following:
• Signal Leads: Terminals S1-S7 & SC; RP, FS, FR & FC; R+, R-, S+, S-; & AM & AC.
• Control Leads: Terminals P1, P2 & PC; MA, MB & MC.
• Use twisted shielded or twisted-pair shielded wire (20-16 AWG [0.5 – 1.25mm2]) for control and signal circuit leads. The shield sheath MUST be connected at the drive end ONLY (terminal
). The
other end should be dressed neatly and left unconnected (floating). See Figure 1-2.
• Signal leads and feedback leads (PG) must be separated from control leads main circuit leads, and
any other power cables, to prevent erroneous operation caused by electrical noise.
• Lead length should NOT EXCEED 164 feet (50 meters). Wire sizes should be determined considering the voltage drop.
• All AC relays, contactors and solenoids should have RC surge supressors installed across their coils.
• All DC relays, contactors and solenoids should have diodes installed across their coils.
SHIELD SHEATH
OUTER JACKET
TO DRIVE
SIGNAL
TERMINALS
TO
EXTERNAL
CIRCUIT
TO SHIELD
SHEATH
TERMINAL
(TERM.
)
WRAP BOTH ENDS
OF SHEATH WITH
INSULATING TAPE
DO NOT
CONNECT
CRIMP
CONNECTION
Figure 1-2. Shielded Sheath Termination
C. Grounding
• The drive must be solidly grounded using the main circuit ground terminal
.
• If Drive is installed in a cabinet with other equipment, ground leads for all equipment
should be connected to a common low-impedance ground point within the cabinet.
• The supply neutral should be connected to the ground point within the cabinet.
• Select appropriate ground wire size from Table 1-1.
• Make all ground wires as short as practical.
• NEVER ground the drive in common with welding machines, or other high power electrical
equipment.
• Where several drives are used, ground each directly to the ground point (see Figure 1-1).
DO NOT FORM A LOOP WITH THE GROUND LEADS.
• When connecting a motor to the drive’s output terminals, include a separate ground wire. Attach
ground wire solidly to motor frame and to drive’s ground terminal
.
• When using armored or shielded cable for connection between drive and motor, solidly connect
armor or shield to motor frame, and to the drive’s ground terminal
.
•
•
CORRECT
•
•
•
•
CORRECT
1-9
•
•
•
NOT
ACCEPTABLE
•
Continued
1.4 ELECTRICAL INSTALLATION
Table 1-3. Terminal Functions and Signals of Control Circuit
DATA
FUNCTION
DESCRIPTION*
S1
Multi-Function-Input 1
Factory setting is " Forward Run/Stop " (1).
(Forward run when closed, stop when open)
S2
Multi-Function-Input 2
Factory setting is " Reverse Run/Stop " (1).
(Reverse Run when closed, stop when open)
S3
Multi-Function-Input 3
Factory setting is " External Fault (NO contact)
input " (1)
S4
Multi-Function-Input 4
Factory setting is " Fault Reset " (1)
S5
Multi-Function-Input 5
Factory setting is " Multi-step Speed
Reference 1 " (1)
S6
Multi-Function-Input 6
Factory setting is " Multi-step Speed
Reference 2 " (1)
S7
Multi-Function-Input 7
Factory setting is " Jog Reference" (1)
SC
Sequence common for terminals S1-S7.
Common terminal for sequence inputs
FS
Frequency reference power supply
+12 VDC
FR
Frequency reference input
0 to +10V/100% (20K ohms) or 4-20 mA (250 Ω)
RP
Frequency reference –Pulse Train input
30 KHz maximum pulse input
FC
Frequency reference input common
0V
MA
MB
MC
Multi-function contact output – NO contact
Factory
Multi-function contact output – NC contact Setting
Multi-function contact output – Common
is " Fault "
Contact capacity:
250 Vac at 1A or below
30 Vdc at 1A or below
AM
Multi-function analog monitor (+) Factory setting is
" Output frequency "
0-10V = 0-100%
Monitor output: 0 to +10V; 2 mA maximum.
AC
Analog monitor common
0V
P1
Multi-Function Open
Collector Output 1
Factory setting is
" Drive Running "
Photocoupler output:
48 VDC; 50 mA or less.
P2
Multi-Function Open
Collector Output 2
Factory setting is
" Speed Agree "
PC
Multi-Function Open
Collector Output common
0V
R+
Receive input (+)
MODBUS
R–
Receive input (–)
communication
RS-485/422 MODBUS protocol,
S+
Send output (+)
RS-485 or RS-422.
19.2 kps max.
S–
Send output (–)
NOTES:
1.
These inputs have factory settings based on 2-wire reset. For 3-wire reset definitions, see Figure 1-6.
1-10
Continued
1.4 ELECTRICAL INSTALLATION
D. Auxiliary Input and Output Power Option Devices
A disconnect device (circuit breaker, contactor, disconnect switch, etc.) should NOT be used as a
means of starting and stopping the drive or motor.
A disconnect device can be installed for emergency stop purposes, but when that disconnect device
is opened, there may be loss of electrical braking.
Figure 1-3 is a factory guideline for proper wiring practices and relative locations within the electrical
path from the line to the load. It does not imply what devices are needed for a particular application,
nor does it show what devices were shipped with a particular order. Therefore, disregard those items
in the diagram which are not being used in your installation. However, it is recommended that an
input or DC reactor be used with all Drive ratings when wired to a source of 600 kVA or greater.
Mount all optional power devices close to the drive, and keep electrical connections as short as
possible.
DO NOT run input and output wiring in the same conduit.
ISOLATION
TRANSFORMER
CUSTOMER'S
3Ø A.C. LINE
POWER
SUPPLY
INPUT
RFI FILTER
L3
H3
X3
C1(L3)
L2
H2
X2
B1(L2) I
L1
H1
X1
A1(L1) E
L
N
INPUT
REACTOR
L (L3)C2
O
(L2)B2
A
D (L1)A2
C1
C2
B1
B2
A1
A2
(G)
EARTH GROUND
SEE NOTE 2
NOTES
1.
2.
Connect drive ground terminal or panel to
earth ground. Always use low impedance
paths and connections.
Mount input and output RFI filters physically
as close to the drive as possible (on the same
panel, if possible). Filters should have a solid
connection from filter case or ground terminal
to drive panel or ground terminal (conduit with
good bare metal to bare metal connections
may serve as the path). If multiple input or
output RFI filters are used, they must be
wired in parallel.
3.
Shield conductors with metallic conduit.
4.
Connect output conduit in a manner that
allows it to act as an unbroken shield from the
drive panel to the motor casing.
5.
RF noise filter (different from RFI filter) part
no. 05P00325-0023 is a delta wye capacitor
network which is wired in parallel with the
drive input terminals. On the smaller drives
with die cast chassis, it must be mounted
externally. On the larger drives with sheet
metal chassis, it may be mounted inside the
area where the input power wiring enters the
drive. On units equipped with bypass, it may
be wired to the primary side of the circuit
breaker and mounted to the bypass panel or
sidewall.
6.
RF NOISE
FILTER
SEE NOTE 5
SEE NOTE 3
EARTH GROUND
SEE NOTE 2
L1, L2, L3
Ckt Brkr L1, L2, L3
Output
T1, T2, T3
Unwired side of
Overload relay
L11 L21 L31
DC
REACTOR
+ 1
SEE NOTE 6
+ 2
OUTPUT
T1
T2
T3
EARTH GROUND
SEE NOTE 1
SEE NOTES 3, 4
1
OUTPUT
RFI FILTER
2
3
IN
OUT
4
5
6
A1
B1
C1
A2
B2
C2
TO CASE
EARTH
GROUND
SEE NOTE 2
SEE NOTES 3, 4
OUTPUT
REACTOR
Drive w/ Bypass
Input
L2 L3
INPUT
AC DRIVE
Connection points:
Drive w/o Bypass
L1
SEE NOTES 3, 4
T1
T2
T3
A.C. MOTOR
Figure 1-3. Customer Connection Diagram For Isolation Transformers, Input Reactors,
Input RFI Filters, DC Reactors, Output Reactors and Output RFI FIlters
1-11
1.4 ELECTRICAL INSTALLATION
Continued
E. Conformance to European EMC Directive
In order to conform to EMC standards, the following methods are required for line filter application,
cable shielding and drive installation.
The line filter and Drive must be mounted on the same metal plate. The filter should be mounted as
close to the drive as practical. The cable must be kept as short as possible and the metal plate
should be securely grounded. The ground of the line filter and the drive must be bonded to the
metal plate with as much bare-metal contact as possible.
For main circuit input cables, a screened cable is recommended within the panel and is also
suggested for external connections. The screen of the cable should be connected to a solid ground.
For the motor cables, a screened cable (max. 20 m) must be used and the screen of the motor cable
should be connected to ground at both ends by a short connection, again using as much bare-metal
contact as practical.
For a more detailed explanation, refer to the manufacturer document EZZ006543, “Installation
Guidelines For EMC Directive using AC Drive Products.”
Table 1-4 and Figure 1-4 show the line filter list for EMC standards and the installation/wiring of the
Drive and line filter.
Table 1-4. Line Filters for EMC Standards
Model
CIMRV7*
MV
20P1
A001
20P2
A002
20P4
A003
20P7
A005
21P5
A008
22P2
A011
23P7
A017
25P5
A025
27P5
A033
40P2
B001
40P4
B002
40P7
B003
41P5
B005
42P2
–
43P7
B009
45P5
B015
47P5
—
(1)
Part Number
Rated
FIL00
Current (A)
Line Filter
Weight
Dimensions in in. (mm)
lbs. (kg)
H x W x D (1)
Mounting Dim. in in. (mm) Screw
H1 x W1
Size
1083
10
1.8 (0.8)
7.6 x 3.2 x 2.0 (194 x 82 x 50)
7.1 x 2.4 (181 x 62)
M5
1084
16
2.2 (1.0) 6.7 x 4.4 x 2.0 (169 x 111 x 50)
6.1 x 3.6 (156 x 91)
M5
1085
26
2.4 (1.1) 6.9 x 5.7 x 2.0 (174 x 144 x 50) 6.3 x 4.7 (161 x 120)
M5
1100
50
5.1 (2.3) 12.0 x 7.2 x 2.2 (304 x 184 x 56) 11.3 x 5.9 (288 x 150)
M6
1086
5
2.2 (1.0) 6.7 x 4.4 x 1.8 (169 x 111 x 45)
6.1 x 3.6 (156 x 91)
M5
1087
10
2.2 (1.0) 6.7 x 4.4 x 1.8 (169 x 111 x 45)
6.1 x 3.6 (156 x 91)
M5
1088
15
2.4 (1.1) 6.9 x 5.7 x 2.0 (174 x 144 x 50) 6.3 x 4.7 (161 x 120)
M5
1101
30
5.1 (2.3) 12.0 x 7.2 x 2.2 (304 x 184 x 56) 11.3 x 5.9 (288 x 150)
M6
D is the distance the filter will extend outward from the surface of the metal plate.
4-d
H1
W1
D
W
1-12
H
1.4 ELECTRICAL INSTALLATION
Continued
Figure 1-4. Installation of Line Filter and V7 Drive
1-13
Continued
1.4 ELECTRICAL INSTALLATION
F. Interconnection - 2 Wire
NOTES FOR FIGURE 1-5
✱
– Indicates components not supplied.
– Main circuit terminal.
– Indicates control circuit terminal.
( ) – Indicates alternate terminal marking, i.e., (R) and L1.
▲
●
– Function labels shown for these terminals are determined by factory settings of n050
through n056 (see paragraph 5.18).
– Function labels shown for these terminals are determined by factory settings of n057 through n059
(see paragraph 5.19).
♦
– Function label shown for this terminal is determined by factory setting of n004 (see paragraph 5.11A).
■
– Function labels shown for these terminals are determined by factory setting of n066 (see paragraph 5.17).
1.
Insulated twisted shielded wire is required.
2-conductor #18 GA. (Belden #8760 or equivalent).
3-conductor #18 GA. (Belden #8770 of equivalent).
Connect shield ONLY AT the Drive END (ground terminal
). Stub and isolate other end.
2.
+12V voltage output current capacity of control terminal FS is 20mA max.
3.
The Drive’s Electronic Thermal Overload function (n036, n037) meets standards set by UL and CUL for motor thermal overload protection. If local code requires a separate mechanical overload protection, an overload relay should
be installed, interlocked with the Drive as shown. It should be the manual reset type to prevent automatic restart following a motor fault and subsequent contact reclosure after cool down.
4.
Customer to connect terminal
5.
If the Digital Operator is used, remote operators, which duplicate functions of its command keys may not be
required. See Figure 4-1.
6.
For installation of Braking Resistor or Braking Resistor unit, refer to Appendix 6, “Dynamic Braking Option.”
7.
An optional DC reactor may be added for harmonic attenuation, if needed. See separate instruction sheet for wiring.
8.
If application does not allow reverse operation, parameter n006 , Reverse Run Prohibit Selection, should be set to
“ 1 ” (Reverse Run Disabled), and the Reverse Run/Stop input can be eliminated.
to earth ground.
WARNING
9.
Input fuses are required for proper branch circuit short circuit protection for all NEMA Type 4 drives. Failure
to use recommended fuses (see appendix 4) may result in damage to the drive and/or personal injury.
1-14
Continued
1.4 ELECTRICAL INSTALLATION
3-PHASE
POWER SUPPLY
(Use L1 (R) and
L2 (S) for
single-phase
input)
(Note that drive must
be derated by 50%
on 3-Phase Models)
MCCB
*
1-3FU*
(See Note 9)
L1
L3
FORWARD
RUN/STOP
See
Note 3)
FOR DYNAMIC BRAKING
(See Note 6)
+1
B1
+2
–
L1 ( R )
L2 ( S )
L3 ( T )
L2
*1OL
FOR DC REACTOR
(See Note 7)
REVERSE (See Note 8)
RUN/STOP
EXTERNAL
FAULT
T2 ( V )
T3 ( W )
V7
OR
V74X
(See Note 4)
(See Note 5)
S2
AM
ANALOG MONITOR
MULTI-FUNCTION
CONTACT INPUT
ANALOG OUTPUT
MONITOR 0 to +10VDC
FM
AC
MA
MB
MC
S5
MULTI-STEP
SPEED REF 2
*
AC
MOTOR
S1
S4
MULTI-STEP
SPEED REF 1
* 1OL (See Note 3)
T1 ( U )
S3
FAULT
RESET
B2
* OUTPUT
FREQUENCY
FAULT
MULTI-FUNCTION
OUTPUT CONTACT
250VAC, 1A OR LESS
30VDC, 1A OR LESS
S6
JOG REFERENCE
S7
SC
LOGIC
COMMON
TERMINAL
P1
RUNNING
PC
(See Note 1)
*
1R
2K
SHIELD
CONNECTION
TRAIN INPUT
RP PULSE
(MAX 30KHz)
P2
MULTI-FUNCTION
PHOTOCOUPLER
OUTPUT
48V, 50mA OR LESS
SPEED
COINCIDENCE
FREQUENCY
FS SETTING POWER SUPPLY
FREQUENCY
REF.
(See Note 5)
*
1RH
MANUAL
SPEED
2KΩ
(+12V, 20mA) (See Note 2)
FR REFERENCE
(0 to 10V, 20KΩ /
4 to 20mA, 250Ω )
FC
OV
0-10VDC
or
4-20mA
FREQUENCY
SETTING
POT
MIN
SW1
PNP
NPN
R+
MODBUS
COMMUNICATIONS
RS485/422
19.2 KBPS MAX.
RS+
MAX
SW2
1 ON
OFF
2 I
V
MODBUS
(TERMINAL
RESISTANCE:
120Ω, 0.5W)
S-
Figure 1-5. Standard Connections (2-Wire Control)
FIG. 1-9
(Parameter n001 set to “10”)
H. Inspection. After wiring is complete, verify that all wiring is correctly installed,
excess screws and wire clippings are removed from inside of unit, screws are
securely tightened, and exposed wire does not contact other wiring or terminals.
CAUTION
If a FWD or REV run command is given from the control circuit terminal when the operation method selection function ( n003 ) is set to “ 1 ” and the “LO/RE”
selection is set to “RE”, the motor will start automatically as soon as power is applied to the main circuit.
1-15
Continued
1.4 ELECTRICAL INSTALLATION
G. Interconnection - 3 Wire
NOTES FOR FIGURE 1-6
✱
– Indicates components not supplied.
– Main circuit terminal.
– Indicates control circuit terminal.
( ) – Indicates alternate terminal marking, i.e., (R) and L1.
▲
●
1.
– Function labels shown for these terminals are determined by factory settings of n050
through n056 (see paragraph 5.18).
– Function labels shown for these terminals are determined by factory settings of n057 through n059
(see paragraph 5.19).
♦
– Function label shown for this terminal is determined by factory setting of n004 (see paragraph 5.11A).
■
– Function labels shown for these terminals are determined by factory setting of n066 (see paragraph 5.17).
Insulated twisted shielded wire is required.
2-conductor #18 GA. (Belden #8760 or equivalent)
3-conductor #18 GA. (Belden #8770 or equivalent)
Connect shield only at the Drive end (ground terminal (
) ). Stub and isolate other end.
2.
+12V voltage output current capacity of control terminal FS is 20mA max.
3.
The Drive’s Electronic Thermal Overload function (n036, n037) meets standards set by UL and CUL for motor thermal
overload protection. If local code requires a separate mechanical overload protection, an overload relay should be
installed, interlocked with the Drive as shown. It should be the manual reset type to prevent automatic restart following
a motor fault and subsequent contact reclosure after cool down.
4.
Customer to connect ground terminal (
5.
If Digital Operator is used, remote operators which duplicate functions of its command keys (see Figure 4-1) may not
be required.
6.
For installation of Braking Resistor or Braking Resistor Unit, refer to Appendix 6, “Dynamic Braking Option”.
7.
An optional DC reactor may be added for harmonic attenuation, if needed; see separate instruction sheet for wiring.
8.
If application does not allow reverse operation, parameter n006 , Reverse Run Prohibit Selection, should be set to “ 1 ”
(Reverse Run Disabled) and Fwd/Rev input can be eliminated.
) to earth ground.
WARNING
9.
Input fuses are required for proper branch circuit short circuit protection for all NEMA type 4 drives. Failure to
use recommended fuses (see appendix 4) may result in damage to the drive and/or personal injury.
CAUTION
Parameter n050 must be set to “ 0 ”, AND parameter
n001 must be set to “ 11 ”. Resetting drive parameter
n001 to “ 10 ” may cause the motor to run in reverse
direction WITHOUT A RUN COMMAND, and possibly result
in equipment damage or personal injury.
1-16
Continued
1.4 ELECTRICAL INSTALLATION
3-PHASE
POWER SUPPLY
(Use L1 (R) and
L2 (S) for
single-phase
input)
(Note that drive must
be derated by 50%
on 3-Phase Models)
MCCB
1-3FU*
(See Note 9)
L1
FOR DYNAMIC BRAKING
(See Note 6)
+1
B1
+2
–
L1 ( R )
L2 ( S )
L3 ( T )
L2
L3
RUN
B2
1OL (See Note 3)
T1 ( U )
T2 ( V )
T3 ( W )
V7
OR
V74X
AC
MOTOR
(See Note 4)
S1
(See Note 8)
STOP
(See Note 5)
S2
FORWARD/
REVERSE
1OL
See
Note 3)
FOR DC REACTOR
(See Note 7)
ANALOG MONITOR
S3
FAULT
RESET
S4
MULTI-STEP
SPEED REF 1
MULTI-FUNCTION
CONTACT INPUT
FM
AC
MA
MB
MC
S5
MULTI-STEP
SPEED REF 2
ANALOG OUTPUT
MONITOR 0 to +10VDC
AM
FAULT
OUTPUT
FREQUENCY
MULTI-FUNCTION
OUTPUT CONTACT
250VAC, 1A OR LESS
30VDC, 1A OR LESS
S6
JOG REFERENCE
S7
SC
LOGIC
COMMON
TERMINAL
P1
RUNNING
PC
(See Note 1)
1R
2KΩ
SHIELD
CONNECTION
PULSE
TRAIN INPUT
RP (MAX 30KHz)
P2
MULTI-FUNCTION
PHOTOCOUPLER
OUTPUT
48V, 50mA OR LESS
SPEED
COINCIDENCE
FREQUENCY
FS SETTING POWER SUPPLY
FREQUENCY
REF.
(See Note 5)
1RH
MANUAL
SPEED
2KΩ
(+12V, 20mA) (See Note 2)
FR REFERENCE
(0 to 10V, 20KΩ /
4 to 20mA, 250Ω)
FC
OV
0-10VDC
or
4-20mA
FREQUENCY
SETTING
POT
MIN
SW1
PNP
NPN
R+
MODBUS
COMMUNICATIONS
RS485/422
19.2 KBPS MAX.
RS+
OFF
V
MAX
SW2
1 ON
2 I
MODBUS
(TERMINAL
RESISTANCE:
120Ω, 0.5W)
S-
Figure 1-6. Standard Connections (3-Wire Control)
(Parameter n001 set to “11”)
H. Inspection. After wiring is complete, verify that all wiring is correctly installed,
excess screws and wire clippings are removed from inside of unit, screws are
securely tightened, and exposed wire does not contact other wiring or terminals.
CAUTION
If a FWD or REV run command is given from the control
circuit terminal when the operation method selection
function ( n003 ) is set to “ 1 ” and the “LO/RE” selection
is set to “RE”, the motor will start automatically as soon
as power is applied to the main circuit.
1-17
1-18
Section 2. INITIAL START-UP
2.1 PRE-POWER CHECKS
• Verify wires are properly connected and no erroneous grounds exist.
• Remove all debris from the Drive enclosure, such as loose wire clippings, metal shavings, etc.
• Verify all mechanical connections inside the Drive are tight.
• Verify motor is not connected to load.
• Apply input power only after the front cover is in place. DO NOT remove the front cover or Digital
Operator while input power is on.
• Determine the proper control method for the application.
Open Loop Vector Control - Use section 2.2 for startup instructions
Parameter n002 = 1. Open Loop Vector Control method should be used for
most constant torque applications of the Drive. With this control method
there is excellent starting torque and excellent speed regulation. The startup
procedure for this control method is slightly more complicated.
V/f Control - Use section 2.3 for startup instructions
Parameter n002 = 0. V/f control should be used for most variable torque
applications. Variable torque applications would include: fan, blower,
centrifugal pump, and mixers. Generally variable torque loads do not require
high levels of starting torque. V/f control can also be used for some constant
torque loads where starting torque and speed regulation are not critical.
2-1
2.2 OPEN LOOP VECTOR STARTUP
NOTE: 2-wire or 3-wire sequence selection must be made prior to using this startup procedure or
making any other adjustments (parameter n001).
Table 2-1. Open Loop Vector Startup Procedure
DESCRIPTION
Set the highest parameter
access level.
This will allow all parameters
to be viewed and set.
DIGITAL OPERATOR
DISPLAY
KEY SEQUENCE
PRGM
DSPL
Press the
key until the
is lit on the digital operator.
PRGM
LED
PRGM
Press
DATA
ENTER
.
PRGM
V
Press
three times.
PRGM
Press
Set drive for Open Loop
Vector control.
This is accomplished by setting n002 = 1
DATA
ENTER
.
V
PRGM
Press
DATA
ENTER
then
V
Use the
in the display.
.
PRGM
V
&
keys to set a “1”
PRGM
Then press
Set motor rated voltage.
(This can be obtained from
the nameplate of the motor.)
DATA
ENTER
.
V
Press and hold
until n012 is displayed on the digital operator.
Then press
DATA
ENTER
PRGM
PRGM
.
(1)
V
V
Use the
&
keys until the
number in the display matches the motor
rated voltage.
Then press
DATA
ENTER
PRGM
(1)
PRGM
.
2-2
Table 2-1. Open Loop Vector Startup Procedure - Continued
DESCRIPTION
Set motor rated current.
(This can be obtained from
the nameplate of the motor.)
KEY SEQUENCE
DIGITAL OPERATOR
DISPLAY
V
Press and hold
until n036 is displayed on the digital operator.
Then press
DATA
ENTER
PRGM
.
(1)
V
V
Use the
&
keys until the
number in the display matches the motor
rated current.
Then press
Set the motor rated slip.
This can be calculated by
using the following formula:
V
Then press
Example:
Slip = (1800 - 1725) * 4
120
PRGM
.
Press and hold
until n106 is displayed on the digital operator.
Slip = (Ns-Nr) * P
120
Where:
Ns = Motor synch. speed (2)
Nr = Motor rated speed
P = Number of motor poles
DATA
ENTER
DATA
ENTER
PRGM
.
(1)
V
V
Use the
&
keys until the
number in the display matches the calculated
slip value (see equation at left).
Then press
DATA
ENTER
PRGM
.
Slip = 2.5
Prepare to test run the
drive from the Digital
Operator. Motor should be
disconnected from the load.
Press and hold
the
This will set the drive into the
“Local” mode and bring up
the motor current display.
LO/RE
DSPL
several times until
LED is lit.
LO/RE
V
Press the
LO/RE
key once.
Display the drive’s output current by pressing
IOUT
DSPL
four times. Turn the Digital Operator
Pot all the way to the left (counter-clockwise.
2-3
Table 2-1. Open Loop Vector Startup Procedure - Continued
DESCRIPTION
Test run the drive from the
Digital Operator.
KEY SEQUENCE
DIGITAL OPERATOR
DISPLAY
WARNING: The next key press will cause
the motor to turn! Take appropriate safety
precautions!
RUN
Press the
key then slowly turn the
Digital Operator Pot to the right about 1/4 of a
turn. The display on the drive will show the
actual motor amps.
IOUT
(1)
Operation checkpoints:
• Motor rotates smoothly
• Motor rotates in correct direction. (If motor
does not rotate in the proper direction,
stop the motor and remove power from the
Drive. Switch motor connections T1 (U)
and T2 (V) at the Drive.)
• Motor has no abnormal vibration or noise.
• Acceleration and deceleration are smooth.
• Unit is not overloaded. (Displayed current
does not exceed drive rated current).
Determine the motor “no
load current.”
With the drive still running, turn the Digital
Operator Pot all the way to the right (full
speed) and record the current on the display.
IOUT
(1)
Actual Value: ________________________
Press the
STOP
RESET
button to stop the drive.
2-4
IOUT
Table 2-1. Open Loop Vector Startup Procedure - Continued
DESCRIPTION
KEY SEQUENCE
Set the motor “no load current” in the drive.
Press the
Motor no load current is set
as a percentage of motor
rated current. It is calculated
using the formula:
DSPL
PRGM
V
Press the
Inoload *100 = n110
Irated
key four times.
DIGITAL OPERATOR
DISPLAY
Where:
Inoload = Motor no load current
Press the
key four times.
DATA
ENTER
key.
PRGM
PRGM
(measured in the
previous step)
Irated = Motor rated current
(from motor
nameplate)
(1)
V
Example:
2.5 * 100 = 60
4.2
Press the
This completes the startup.
Make further programming
changes as required.
V
Use the
&
keys until the
number in the display matches calculated noload current.
DATA
ENTER
key.
DSPL
Press the
key to get out of the programming mode.
(1)
The number in the display may be different than shown.
(2)
Motor synchronous speed can be calculated using the following formula:
120 x motor rated frequency
synch. speed =
number of motor poles
For 60 Hz Rated Motors
Poles
Synchronous Speed
2
3600 RPM
4
1800 RPM
6
1200 RPM
8
900 RPM
2-5
PRGM
FREF
(1)
2.3 V/f STARTUP PROCEDURE
IMPORTANT
2-wire or 3-wire sequence selection must be made prior to any other adjustments (Parameter n001).
Table 2-2. V/f Startup Procedure
DESCRIPTION
Set the highest parameter
access level.
This will allow all parameters
to be viewed and set.
DIGITAL OPERATOR
DISPLAY
KEY SEQUENCE
PRGM
DSPL
Press
key until the
on the digital operator.
Press
DATA
ENTER
PRGM
LED is lit
PRGM
.
V
Press
Press
Set drive for V/f control.
This is accomplished by setting n002 = 0
PRGM
three times.
DATA
ENTER
PRGM
.
V
Press
DATA
ENTER
then
V
Use the
in the display.
Then press
V
&
DATA
ENTER
.
keys to set a “0”
PRGM
PRGM
PRGM
.
2-6
Table 2-2. V/f Startup Procedure - Continued
DESCRIPTION
Set motor rated current.
(This can be obtained from
the nameplate of the motor.)
KEY SEQUENCE
DIGITAL OPERATOR
DISPLAY
V
Press and hold
until n036 is displayed on the digital operator.
Then press
DATA
ENTER
PRGM
.
(1)
V
V keys until the
Use the
&
number in the display matches the motor
rated current.
Then press
DATA
ENTER
PRGM
.
Set the V/f pattern.
Parameters n011 through
n017 set the V/f pattern. Table
5-4 in section 5.27 lists recommended V/f patterns. The
numbers in parentheses
shown in the example below
are for a 460V / 60 Hz variable torque application (fan or
pump).
Set Parameter n011Maximum output frequency.
(60.0 Hz)
V
Press and hold
until n011 is displayed on the digital operator.
Then press
DATA
ENTER
PRGM
.
(1)
V
V
Use the
&
keys until the
desired number is in the display.
Then press
DATA
ENTER
PRGM
(1)
PRGM
.
2-7
Table 2-2. V/f Startup Procedure - Continued
DESCRIPTION
Set Parameter n012Voltage Max.
KEY SEQUENCE
V
Press
DATA
ENTER
then
.
DIGITAL OPERATOR
DISPLAY
PRGM
(460.0 V)
(1)
V
V
Use the
&
keys until the
desired number is in the display.
DATA
ENTER
Then press
Set Parameter n013Frequency at max. voltage
point (motor rated frequency)
Press
DATA
ENTER
then
(1)
PRGM
.
V
PRGM
.
PRGM
(1)
(60.0 Hz)
V
V
Use the
&
keys until the
desired number is in the display.
DATA
ENTER
Then press
Set Parameter n014Frequency - Midpoint
Press
DATA
ENTER
then
(1)
PRGM
.
V
PRGM
PRGM
.
(30.0 Hz)
(1)
V
V
Use the
&
keys until the
desired number is in the display.
Then press
DATA
ENTER
PRGM
(1)
PRGM
.
2-8
Table 2-2. V/f Startup Procedure - Continued
DESCRIPTION
Set Parameter n015Voltage - Midpoint
KEY SEQUENCE
V
Press
DATA
ENTER
then
.
DIGITAL OPERATOR
DISPLAY
PRGM
(80.4 V)
(1)
V
V keys until the
Use the
&
desired number is in the display.
DATA
ENTER
Then press
Set Parameter n016Frequency - Minimum
Press
DATA
ENTER
then
(1)
PRGM
.
V
PRGM
.
PRGM
(1.5 Hz)
(1)
V
V
Use the
&
keys until the
desired number is in the display.
Then press
Set Parameter n017Voltage - Minimum
DATA
ENTER
DATA
ENTER
then
(1)
PRGM
.
V
Press
PRGM
.
PRGM
(18.4 V)
(1)
V
V keys until the
Use the
&
desired number is in the display.
Then press
DATA
ENTER
PRGM
(1)
PRGM
.
2-9
Table 2-2. V/f Startup Procedure - Continued
DESCRIPTION
Prepare to test run the
drive from the Digital
Operator. Motor should be
disconnected from the load.
This will set the drive into the
“Local” mode, and bring up
the motor current display.
KEY SEQUENCE
DSPL
Press
LED is lit.
several times until the “LO/RE”
DIGITAL OPERATOR
DISPLAY
LO/RE
V
Press the
key once.
LO/RE
Display the drive’s output current by pressing
IOUT
DSPL
four times. Turn the Digital Operator
Pot all the way to the left (counter-clockwise).
Test run the drive from the
Digital Operator
WARNING: The next key press will cause
the motor to turn! Take appropriate safety
precautions!
RUN
Press the
key then slowly turn the
Digital Operator Pot to the right about 1/4 of a
turn. The display on the drive will show the
actual motor amps.
Operation checkpoints:
• Motor rotates smoothly
• Motor rotates in correct direction. (If motor
does not rotate in the proper direction,
stop the motor and remove power from the
Drive. Switch motor connections T1 (U)
and T2 (V) at the Drive to change direction).
• Motor has no abnormal vibration or noise.
• Acceleration and deceleration are smooth.
• Unit is not overloaded. (Displayed current
does not exceed drive rated current).
Press the
STOP
RESET
key.
This completes the startup.
Make further programming
changes as required.
(1)
The number in the display may be different than shown.
2-10
IOUT
(1)
Section 3. OPERATION AT LOAD
After completing the start-up, and programming of constants, turn off the AC main circuit power.
Make additional wiring connections required for the external control functions selected by the constant programming. Connect the driven machine to the motor. Verify that the driven machine is in
running condition, and that no dangerous conditions exist around the drive system.
CAUTION
•
Before applying a RUN command to the Drive, verify that the motor is stopped.
•
NEVER use a motor whose full-load amps exceeds the Drive rating.
•
When starting and stopping the motor, use the operation signals (RUN/STOP, FWD/REV),
NOT a magnetic contactor on the power supply side.
Run the motor under load with control by the Digital Operator using the same procedure as for the
Initial Start-up. If the Digital Operator is used in combination with external commands or external
commands only are used, the procedure must be altered accordingly.
3-1
3-2
Section 4. DIGITAL OPERATOR
4.1 GENERAL
All functions of the Drive are accessed using the Digital Operator. In addition to controlling motor
operation, the operator can enter information into the Drive memory to configure the Drive’s application, by using the Function LEDs.
4.2 DIGITAL OPERATOR
A.
Digital Operator Description
The Digital Operator has a 4-digit LED display. Both numeric and alpha-numeric data can appear on
the display. Indicators and keys on the Digital Operator are described in Figure 4-1.
Display section
Data display
section
DIGITAL
OPERATOR
JVOP-140
Function
LEDs
FREF
FOUT
F/R
Press to switch
between function
LEDs.
DSPL
IOUT
MNTR
LO/RE
PRGM
V
Digital Operator
Potentiometer
(Pot)
RUN
MIN
DATA
ENTER
V
MAX
STOP
RESET
Displays data
to be changed
and enters new
data.
Press to run the motor.
Press to increase
parameter no./data
value.
Press to decrease
parameter no./data
value.
Status indicator
Press to stop the motor,
or reset a drive fault
(1) Not available on V74X.
NOTE:
The JVOP-140 is the standard digital operator for the V7. The Digital Operator of the V74X does not
have a potentiometer (pot) and cannot be removed. All functions will be identical with the exception of
the pot and copy function (section 5-29).
4-1
4.2 DIGITAL OPERATOR
Continued
B. Description of Function LEDs
By pressing the DSPL key on the Digital Operator, the operator can step to each of the seven
Function LEDs and its associated display/setting function:
Press
Press
Press
Press
FREF
DSPL
DSPL
IOUT
DSPL
MNTR
DSPL
Press
Press
Press
F/R
DSPL
LO/RE
DSPL
PRGM
DSPL
FOUT
FREF
—
Frequency Reference Setting
Sets/Displays the Drive operation speed (Hz).
FOUT
—
Output Frequency Monitor
Displays the output frequency (Hz) at which the Drive is currently
operating. This is a monitor only function; the operator cannot
change the displayed value by use of the keypad.
IOUT
—
Output Current Monitor
Displays the level of output current (Amps) that the Drive is
currently producing. This is a monitor only function; the operator
cannot change the displayed value by use of the keypad.
MNTR
—
Monitor Selection
Pressing ENTER allows access to the various Monitor parameters,
U-01 through U-10. These are monitor only functions; the operator
cannot change the displayed value. Accessible during run command.
See section 4.4. for complete listing of all monitor parameters.
F/R
—
FWD/REV Run Selection
Sets the rotation direction of the motor when a Run command is
given by the Digital Operator keypad. Display of For = forward run,
rEu = reverse run.
LO/RE
—
Local / Remote Selection
This toggles between the Local (Digital Operator) and Remote (set by
parameters n003 & n004) modes of operation. This affects both the
start/stop functions, as well as the frequency reference. Local / Remote
status cannot be changed using this LED when a multi-function input
terminal is set for Local/Remote (n050 through n056 set for “17”).
PRGM
—
Parameter Programming
Selects or reads data using parameter number (nXXX). Data is
displayed by pressing the ENTER key, and can be changed by
pressing the “up arrow” or “down arrow” keys. Any changes can be
saved by again pressing the ENTER key. Pressing the DSPL key
exits the Programming mode.
4-2
4.3 STATUS INDICATOR LEDs
There are two indicator LEDs on the front of the Drive. The drive status is indicated by various combinations of ON, Blinking, and OFF conditions of these two LEDs:
(Green)
RUN
(Red)
ALARM
Operation Ready (during stop)
Ramp to Stop (during decel)
Blinking
Long Blinking
Off
Off
Normal Operation (running)
Alarm
On
Blinking or ON
Off
Blinking
Off
On
CONDITION
Fault
For details of how the stats indicator LEDs function during a drive fault, refer to the "TROUBLESHOOTING" SECTION.
4.4 MONITOR DISPLAYS
When using the Monitor Function, a variety of information will appear on the Digital Operator display when each of the U-XX (display only) parameters is selected.
DISPLAY
EXAMPLE
EXAMPLE
MONITORED
ITEM ITEM
MONITORED
01
Frequency reference (Hz)
60.0
02
Output frequency (Hz)
60.0
03
Output current (A)
12.5
04
AC output voltage (V)
230
05
DC Bus voltage ( VPN )
325
06
07
08
Input terminal status
Output Terminal status
Motor Torque (%)
(Open loop vector only)
IIIIIIII (1)
09
10
Fault record (last 4 faults)
Software number
XXXX
Output Power (KW)
Data reception error
PID Feedback (%)
PID Input (%)
PID Output (%)
11
15
16
17
18
(2) Actual display appearance:
MA-MC CLOSED
P1 - PC OPEN
P2 - PC CLOSED
IIIIIIII (2)
72
(3)
oC
0024
99.9
IIIIIIII (4)
35.0
100
75.5
(1) Actual display appearance:
{
CONSTANT
PARAMETER
UnU-
Not used
(3) See section 6 for viewing
of fault log contents.
(4) Actual display appearance:
CRC error
Data length OK
Not used
Parity error
Term. S1 input OPEN
Term. S2 input CLOSED
Term. S3 input OPEN
Term. S4 input CLOSED
Over run error
Framing OK
Timeout error
Not used
Term. S5 input OPEN
Term. S6 input CLOSED
Term. S7 input OPEN
Not used
4-3
4-4
Section 5. PROGRAMMABLE FEATURES
5.1 GENERAL
This section describes features of the Drive which are defined by programmed settings in the various
parameters in memory. Since most features use more than one parameter, the descriptions appear
in alphabetical order by the function name. In Table 5-1, the functions are grouped into operational
categories. To cross reference a particular parameter to the features to which it applies, see the listings in Appendix 1.
Table 5-1. List of Features Defined By Parameters
FUNCTION
SET-UP
Initialization (Reset), 2-Wire or 3-Wire
Volts/Hertz Patterns
Thermal Motor Overload Protection
Control Method Selection
Copy Function (1)
STARTING
Accel Time
S-Curve Characteristics
DC Injection Braking at Start
STOPPING
Stopping Method
Decel Time
DC Injection Braking at Stop
SPEED CONTROL
Frequency Reference, Upper & Lower Limits
Jog Reference
Frequency Reference Selection
Multi-step Speed Setting
PARAGRAPH
REFERENCE
PARAMETER(S)
5.21
5.27
5.25
2.2
5.29
n001
n011 - n017
n036 - n038
n002
n176, n177
5.2
5.3
5.7
n018, n019, n021
n023
n089, n091
5.24
5.2
5.7
n005
n018, n020, n022
n089, n090
5.9
5.12
5.11
5.11
5.10, 5.18F
5.14
5.28
n033, n034
n032, n050 - n056
n004, n008, n009
n004, n024 - n031
n050 - n056, n120 - n127
n056, n100
n003, n004, n151 - n157
n128 - n138, n163, n164
Table A1-1
5.6
5.5
5.18D, E
5.19
5.22
n006
n083 - n086
n080, n175
n050 - n056
n057 - n059, n095
n036, n106, n110 - n113
5.26
5.23
5.31
n103 - n105, n109
n092 - n094, n115, n116
n139 - n146, n158 - n162
5.16
5.4
5.20
5.15
n081
n082
n057 - n059, n096 - n099
n007, n010
5.8
5.11
5.18
5.18
n060, n061
n068 - n079, n149
n050 - n056
n050 - n056
5.19
5.17
5.17
n057 - n059
n066, n067
n150
Up/Down Frequency Setting
Modbus Control
PID Control
REVERSE
Reverse Run Disabled
Critical Frequency Rejection
Carrier Frequency
Speed Search
Speed Coincidence
Slip Compensation
RUNNING IMPROVEMENTS
Torque Compensation
Stall Prevention
Energy Saving
PROTECTIVE FEATURES
Momentary Power Loss Ride-thru
Auto Restart
Overtorque/Undertorque Detection
Miscellaneous Protective Functions
DRIVE CONTROLS, INPUT
Analog Frequency Reference Bias and Gain
Multi-function Analog Inputs
Multi-function Input Terminals
External Fault Terminals
DRIVE OUTPUT
Multi-function Output Terminals
Analog Monitor Output (Multi-function)
Pulse Monitor Output
(1)
Not available on V74X
5-1
5.2 ACCEL/DECEL TIME
A.
n019 : Accel Time 1
n020 : Decel Time 1
Factory setting (each): 10.0 seconds
Range (each): 0.00 to 6000.0 seconds
n021 : Accel Time 2
n022 : Decel Time 2
Factory setting (each): 10.0 seconds
Range (each): 0.00 to 6000.0 seconds
n041 : Accel Time 3
n042 : Decel Time 3
Factory setting (each): 10.0 seconds
Range (each): 0.00 to 6000.0 seconds
n043 : Accel Time 4
n044 : Decel Time 4
Factory setting (each): 10.0 seconds
Range (each): 0.00 to 6000.0 seconds
The drive incorporates four sets of individually programmable acceleration and deceleration times.
Four acceleration and deceleration times can be selected if two Multi-Function Input Terminals
(n050 to n056) are set to ‘11’ (accel/decel time 1) and ‘27’ (accel/decel time 2).
B.
n050 thru n056 : Multi-function Inputs
(Term. S1 thru S7)
Data 11 : Accel/Decel Time Selection 1
Data 27 : Accel/Decel Time Selection 2
The following table shows which acceleration and deceleration times are selected by each
combination of accel/decel time select 1 (n050 thru n056 =11) and accel/decel time select 2
(n050 thru n056 = 27).
Accel/decel time
Select 1 (terminal S1
thru S7)
Accel/decel time
Select 2 (terminal S1
thru S7)
OPEN
OPEN
CLOSED
OPEN
OPEN
CLOSED
CLOSED
CLOSED
C.
n018 : Accel Time Setting Unit
Acceleration time
Deceleration time
Acceleration
n019
Acceleration
n021
Acceleration
n041
Acceleration
n043
Deceleration
n020
Deceleration
n022
Deceleration
n042
Deceleration
n044
time 1
time 2
time 3
time 4
time 1
time 2
time 3
time 4
Factory setting: 0
Range : 0 = 0.1 seconds
1 = 0.01 seconds
In addition to determining the setting resolution, this parameter controls the range of n019 thru n022; if
the resolution is 0.01 sec., the range is 0.00 to 600.00 sec. If the resolution is set to 0.1 sec., the range
is 0.0 to 6000.0 sec.
5-2
5.3 ACCEL/DECEL: S-CURVE CHARACTERISTICS
n023 : S-Curve Selection
Factory setting: 0
Range: 0 to 3
Setting of this parameter
determines the S-curve
(starting) characteristics
of the acceleration ramp.
0 = S-curve disabled
1 = S-curve
of 0.2 seconds
2 = S-curve time
of 0.5 seconds
3 = S-curve time
of 1.0 seconds
RUN
OUTPUT
FREQUENCY
FREQ
COMMAND
Accel ramp per
selected Accel Time
(n019 or n021 )
0
TIME
S-Curve Characteristics
Time (TSC)
NOTE: Actual accel time = Set accel time + (2 * S-curve selection)
Actual decel time = Set decel time + (2 * S-curve selection)
The following figure shows FWD/REV switching and acceleration & deceleration to a stop with
S-curve active.
FORWARD RUN COMMAND
REVERSE RUN COMMAND
DECELERATION
OUTPUT FREQUENCY ACCELERATION
MIN. OUTPUT
FREQUENCY
n016
DC INJECTION
TIME AT STOP
n090
n016
DECELERATION
ACCELERATION
= S-CURVE CHARACTERISTIC
5-3
5.4 AUTO-RESTART
n082 : Number of Auto-Restart Attempts
Factory setting: 0
Range: 0 - 10
When a fault occurs during operation, the Drive can be programmed for an auto-restart operation to
automatically reset the fault. Auto-restart operation will use the number of reset attempts set in this
parameter, up to the maximum of 10. When set to " 0 ", no auto-restarts will be attempted.
Fault contact will not actuate (change state) during auto-restart attempts.
• The following faults can be automatically reset:
oC:
Overcurrent
ou:
Overvoltage (OV)
• The number of restart attempts available will be reset to the n082 setting when:
1. 10 minutes has elapsed without a fault occurring.
2. The RESET key, or external Fault Reset push button, is pressed.
3. Power is removed from the Drive.
5.5 CARRIER FREQUENCY
n080 : Carrier Frequency
Factory Setting: 3
Range: 1 to 4; 7 to 9
The relationship between output frequency and carrier frequency is determined from the set value
of n080 .
(a) For constant carrier frequency, set to " 1 ", " 2 ", " 3 ", " 4 ".
(b) For synchronous mode, set n080 to " 7 ", " 8 ", or " 9 ". These setting values
establish carrier frequencies of 12f, 24f, or 36f, respectively.
n080
SETTING
1
2
3
4
7
8
9
CARRIER FREQUENCY(kHz)
Maximum(FcMAX)
Minimum(FcMIN)
SLOPE
(=Fc)
Fo
2.5
5.0
7.5
10.0
1.0
1.0
1.0
0
0
0
0
12
24
36
2.5
5.0
7.5
10.0
2.5
2.5
2.5
OUTPUT FREQUENCY(Hz)
F1
F2
NA
NA
NA
NA
83.3
41.6
27.7
NA
NA
NA
NA
208.3
104.1
69.4
Fc MAX
CARRIER
FREQUENCY
SLOPE
Fc MIN
0
F1
F2
OUTPUT FREQUENCY
5-4
MODE
CONSTANT
SYNCHRONOUS
DRIVE DERATING FOR HIGHER CARRIER FREQUENCY
Setting carrier frequency to a value higher than its factory setting requires derating of the drive’s output
current - refer to the following table:
Rated
input
230V
460V
New Drive
Model No.
CIMR-V7A*
Rated
Output
Current (A)
MVA001
MVA002
20P10
20P20
0.8
1.6
MVA003
MVA005
20P40
20P70
3.0
5.0
4
4
10
10
MVA008
MVA011
MVA017
21P50
22P20
23P70
8.0
11.0
17.5
3
3
3
7.5
7.5
7.5
7.0
10.0
16.5
MVA025
MVA033
23P71
23P72
25.0
33.0
3
3
7.5
7.5
23.0
30.0
MVB001
MVB002
40P20
40P40
1.2
1.8
3
3
7.5
7.5
1.0
1.6
MVB003
MVB005
MVB009
40P70
41P50
43P70
3.4
4.8
8.6
3
3
3
7.5
7.5
7.5
3.0
4.0
No Derate
MVB015
MVB018
43P70
43P70
3
3
7.5
7.5
14.0
17.0 / 19.8
Old Drive
Model No.
14.8
18.0 / 21.0
n080
Factory
Setting
4
4
(1)
Frequency
(kHz)
10
10
Derated
Output
Current (A)
(2)
No
Derate
(1) Output current rating of 21.0A applies only to V74X drive.
(2) Derated Output Current values are the maximum currents available with a
carrier frequency n080 setting of “4” (10kHz).
Carrier frequency should be decreased as the distance between the drive and the motor increases,
to reduce capacitive coupling in the motor leads.
• For wiring distances greater than 100m (328 ft.), n080 should be set to 5 kHz (data " 2 " )
or less.
n175 : Reduce carrier at low speed selection
Factory Setting: 0
Range: 0 or 1
SETTING
0
1
DESCRIPTION
Disabled
Carrier frequency reduced to 2.5 KHz
When n175 is enabled (= “1”), the carrier frequency will automatically be reduced to 2.5 kHz,
regardless of the setting of n080, whenever the output frequency is at or below 5 Hz AND the
output current is above 110% of drive rated current.
5-5
5.6 CRITICAL FREQUENCY REJECTION
A.
n083 : Prohibited Frequency 1
n084 : Prohibited Frequency 2
n085 : Prohibited Frequency 3
Factory setting (each): 0.00
Range (each): 0.00 to 400.0 Hz
These parameters allow programming of up to three prohibited frequency points for eliminating
problems with resonant vibration of the motor/machine. This feature does not actually eliminate the
selected frequency values, but will accelerate and decelerate the motor through the prohibited
bandwidth.
B.
n086 : Prohibited Frequency Deadband
Factory setting: 0.00
Range: 0.00 to 25.50 Hz
This parameter determines the width of the deadband around each selected prohibited frequency
point.
EXAMPLE:
Vibration encountered between 30.00 and 36.00 Hz.
SOLUTION:
Set n083 to " 33.00 ". This is the center of the problem
frequency band.
Set n086 to " 3.00 ". This will cause the Drive to reject all
frequency command values between 30.00 and 36.00 Hz.
A frequency command in the deadband will be converted to the bottom
value of the deadband, e.g. a command of 33.00 Hz would result in a run
frequency of 30.00 Hz.
Total Deadband = 6.00 Hz
FREQ. CMD
36.00 Hz
n083 = 33.00 Hz
30.00 Hz
± n086 (3.00 Hz)
0
OUTPUT FREQUENCY (Hz)
NOTE: n083 > n084 > n085 - The highest prohibit frequency required needs to be in n083.
The next highest prohibit frequency needs to be in n084, and the lowest prohibit frequency
needs to be in n085.
5-6
5.7 DC INJECTION BRAKING
n016 : Minimum Frequency
Range: 0.1 to 10.0 Hz
n089 : DC Injection Braking Current
(% of Drive Rated Current)
Factory setting: 50 %
n090 : DC Injection Time at Stop
Factory setting: 0.5 sec
Range: 0 to 100 %
Range: 0.0 to 25.5 sec
n091 : DC Injection Time at Start
Factory setting: 0.0 sec
Range: 0.0 to 25.5 sec
DC injection can be used to stop a motor whose rotational direction is uncertain at start-up, or to
help stop a coasting motor.
With ramp to stop enabled (n005 = " 0 " ), after a STOP command is received the Drive controls
motor deceleration according to the Decel Time setting, until output frequency reaches the DC
injection braking start frequency (or Minimum Frequency, n016 ). Then the Drive output is turned off
and DC injection current is applied to the motor. The effective DC injection time and current should
be set to provide adequate stopping without excessive motor heating. The DC injection voltage is
determined by the DC injection braking current and motor impedance.
STOP
RUN COMMAND
RAMP TO STOP
DC
OUTPUT FREQUENCY
DC INJECTION TIME AT
START (n091 )
MINIMUM
FREQUENCY (n016 )
DC INJECTION TIME AT
STOP (n090 )
DC Braking Sequence
5-7
DC
5.8 FREQUENCY REFERENCE BIAS/GAIN (ANALOG)
n060 : Analog Frequency Reference Gain
Factory setting: 100 %
Range: 0 to 255 %
Sets the auto-speed frequency command gain,
in increments of 1%.
n061 : Analog Frequency Reference Bias
Factory setting: 0 %
Range: -100 to 100 %
100%
FREQ.
REF.
(%)
110
100
100%
BIAS
90
GAIN
(–)
FREQ.
REF.
(%)
(+)
0%
0V
FREQ. REF.
INPUT (V)
10V
0%
0V
(–)
FREQ. REF.
INPUT (V)
10V
GAIN
BIAS
–100%
(+)
ADJUSTMENT PROCEDURE:
1.
With no input, adjust Bias (n061 setting) until an output of
0.0 Hz is obtained.
2.
With full scale input, adjust Gain (n060 setting) until an output
of 60.0 Hz (or other desired max. output frequency) is obtained.
NOTE: Follow the same adjustment procedure for other desired frequency setpoints.
For inverse-acting frequency reference
1.
Begin with n060 & n061 settings as shown below.
2.
Fine tune as indicated above.
n060 n061
=
=
100
0
0
100
100%
FREQ
REF.
0%
0V
10V
INPUT VOLTAGE (TERM. FR)
5-8
5.9 FREQUENCY REFERENCE UPPER & LOWER LIMITS
n033 : Frequency Reference Upper Limit
Factory setting: 100 %
Range: 0 to 110 %
n034 : Frequency Reference Lower Limit
Factory setting: 0 %
Range: 0 to 110 %
These two parameters set the range for the frequency command signal. Each is set, in increments
of 1%, as a percentage of maximum frequency (Fmax; n011 ) as established by either the selected
standard V/f pattern or custom V/f pattern.
NOTE: All references are affected by the upper and lower limit points.
EXAMPLE:
n011 = " 60 " Hz (100%)
n033 = " 80 " % = 48Hz – Max. speed
n034 = " 10 " % = 6Hz – Min. speed
100%
n033
80%
OUTPUT
FREQ.
(%)
n034 10%
2.5%
t
NOTE: n033 must be set to a higher value than n034.
5.10 FREQUENCY REFERENCE RETENTION
n100 : Up/Down Hold Memory
Factory setting: 0
Range: 0 or 1
Used with the Up/Down command. To retain the held frequency reference when a stop command is
issued or when power is removed, set n100 to " 1 ".
Setting
Description
0
Not retained
1
Held reference retained
Note: Frequency reference value must
remain unchanged for a minimum of 5
seconds to be retained.
5-9
5.11 FREQUENCY REFERENCE SELECTION
The Drive allows selection of up to twenty-three frequency references. Three are analog inputs,
sixteen are digital presets (selected with multi-function inputs), one is a jog input, one is a pulse
train input, one is via serial communications (MODBUS), and one is from an option cable (see
paragraph 5.32).
A.
Frequency Reference via Analog Input
In order to set the Drive so the frequency reference comes from the analog input, set parameter
n004 as shown in the table below:
PARAMETER
n004
(1)
SETTING
2
3
4
DESCRIPTION
Sets terminal FR for a voltage input (0 to 10V) Set SW2 switch 2 to Off (1)
Sets terminal FR for a current input (4 to 20mA) Set SW2 switch 2 to On (1)
Sets terminal FR for a current input (0 to 20mA) Set SW2 switch 2 to On (1)
SW2 consists of two separate slide switches and can be found just above the upper row of control circuit terminals.
The switch towards the bottom (labeled “2”) connects a 250Ω resistor from terminal FR to FC when set to the “on”
position (to the right). NOTE: All power must be removed from the Drive before SW2 can be set.
B.
Frequency Reference via Digital Presets
In order to set the Drive so the frequency reference comes from the digital presets, the following
parameters need to be set:
PARAMETER
SETTING
n024
thru
n031
User
Set
n050
thru
n056
6, 7, 8,
and/or
9
n120
thru
n127
User
Set
DESCRIPTION
Eight Frequency References
Sets the multi-function inputs so selection of the various references is
possible with contact closures.
Eight More Frequency References
Depending upon how many preset references are required determines the actual settings of n050
thru n056. Several examples are listed below.
5-10
5.11 FREQUENCY REFERENCE SELECTION
Example 2 - Eight preset references
Programming: n054 = 6, n055 = 7 and n056 = 8
Example 1 - Four preset references
Programming: n054 = 6 and n055 = 7
DIGITAL PRESET
S6
(2)
Selectable Reference
DIGITAL PRESET
S5
Open
Open
n025
Open
Closed
n026
Closed
Open
n027
Closed
Continued
S7
S6
S5
Open
Open
Open
n025
Open
Open
Closed
n026
Open
Closed
Open
n027
Open
Closed
Closed
n028
Closed
Open
Open
n029
Closed
Open
Closed
n030
Closed
Closed
Open
n031
Closed
Closed
Closed
Selectable Reference
Closed
(2)
Example 3 - Sixteen preset references
Programming: n053 = 6, n054 = 7, n055 = 8 and n056 = 9
DIGITAL PRESET
S7
S6
S5
S4
Open
Open
Open
Open
n025
Open
Open
Open
Closed
n026
Open
Open
Closed
Open
n027
Open
Open
Closed
Closed
n028
Open
Closed
Open
Open
n029
Open
Closed
Open
Closed
n030
Open
Closed
Closed
Open
n031
Open
Closed
Closed
Closed
n120
Closed
Open
Open
Open
n121
Closed
Open
Open
Closed
n122
Closed
Open
Closed
Open
n123
Closed
Open
Closed
Closed
n124
Closed
Closed
Open
Open
n125
Closed
Closed
Open
Closed
n126
Closed
Closed
Closed
Open
n127
Closed
Closed
Closed
Closed
Selectable Reference
(2)
The Selectable Reference is chosen from the following
list:
(2)
REFERENCE SOURCE
Digital Operator Speed Pot
Digital Preset Reference parameter n024
Analog Input Terminal FR
Pulse Train Reference
Serial Communications
C.
PROGRAMMING
n004 = 0
n004 = 1
n004 = 2, 3, or 4
n004 = 5
n004 = 6
Jog Reference - See paragraph 5.12
5-11
5.11 FREQUENCY REFERENCE SELECTION
Continued
D.
Frequency Reference via Pulse Train Input
In order to set the Drive so the frequency reference comes from a pulse train, set the following
parameters.
PARAMETER
n004
n149
SETTING
5
User
Set
DESCRIPTION
Sets reference source as a pulse train at terminals RP & FC
Sets the input scaling for the pulse train input
Pulse Source Specifications
•
Low-level voltage: 0.8V or less
•
High-level voltage: 3.5 to 32V
•
Duty Cycle: 30 to 70% - high
•
Pulse Frequency: 0 to 30 kHz
GPDDrive
Drive
RP
Pulse
Source
FC
n149 : Pulse Train Input Scaling
Factory Setting: 2500
Range: 100 to 3000 (x 10 Hz)
This parameter scales the incoming frequency on terminal RP by using the following equation
Frequency reference =
E.
Pulse Source Frequency n011
*
n149 * 10
Frequency Reference via Serial Communications - See paragraph 5.14
5-12
5.12 JOG REFERENCE
n032 : Jog Reference
Factory setting: 6.00 Hz
Range: 0.00 to 400.0 Hz
n050 thru n056 : Multi-function Inputs
(Term. S1 - S7)
Data 10 : Jog Selection
When jog operation is selected (by external Jog and Run signals), the Drive output will ramp to the
output level set by this parameter.
When an external Jog signal is present, it will override the existing operation mode and the Drive
will ramp to the level set by this parameter.
EXAMPLE:
OPERATION BY REMOTE SIGNAL INPUT (RUN & JOG)
RUN
*
(Term. S1-S7) JOG
FREQ. CMD
n032 JOG
REF.
0
RUN
*
(Term. S1-S7) JOG
FREQ. CMD
n032 JOG
REF.
0
* Or FWD
Also see descriptions of MULTI-FUNCTION INPUT TERMINALS, paragraph 5.18.
5-13
5.13 LOCAL/REMOTE REFERENCE & SEQUENCE SELECTION
The Drive has the ability to have either a local or a remote reference and sequence selection.
Local -
Run and stop functions are controlled by the buttons on the digital operator (n007). The
frequency reference can come from a digital preset reference (n024 & n009) or the
digital operator pot (n008).
Remote -
Run and stop functions are determined by parameter n003. The frequency reference is
determined by parameter n004.
Switching between local and remote is accomplished either by the LO/RE LED on the digital operator
or by the use of a multi-function input terminal programmed to data “17” (see paragraph 5.18A).
n003 : Operation Method Selection
SETTING
Factory setting: 1
DESCRIPTION
0
STOP
RESET
RUN
Run and stop is controlled by the
and
buttons on the digital operator.
Run and stop is controlled by the multi-function input terminals
2-Wire control - Run Forward (n050 is set to a data of “1”)
Run Reverse (n051 is set to a data of “2”)
3-Wire control - Parameter n052 needs to be set to a data of “0”
Run is controlled by a momentary closure on terminal S1
Stop is controlled by a momentary open on terminal S2
Forward/Reverse is controlled by terminal S3
Run and stop is controlled by serial communications
1
2
n004 : Reference Selection
SETTING
0
1
2
3
4
5
6
DESCRIPTION
Frequency reference
Frequency reference
Frequency reference
Frequency reference
Frequency reference
Frequency reference
Frequency reference
is
is
is
is
is
is
is
controlled
controlled
controlled
controlled
controlled
controlled
controlled
Factory setting: 2
by
by
by
by
by
by
by
the digital operator potentiometer.
a digital preset speed (n024) and is affected by n009.
the analog input terminal FR and is 0 - 10V DC
the analog input terminals FR and is 4 - 20mA
the analog input terminal FR and is 0 - 20mA
the Pulse Train Reference terminal RP.
serial communications.
n007 : Stop Key Function
SETTING
Factory setting: 0
Range: 0 or 1
DESCRIPTION
0
STOP
RESET
1
STOP
RESET
key is effective at all times (regardless of programming of n003)
key is effective only when the run/stop command is from the digital operator (n003 = 0)
5-14
5.13 LOCAL/REMOTE REFERENCE & SEQUENCE SELECTION
n008 : Reference Selection - Digital Operator
Continued
Factory setting: 0
Range: 0 or 1
This parameter is only effective when the Drive is in the local mode.
SETTING
0
1
DESCRIPTION
Frequency reference is controlled by the digital operator potentiometer
Frequency reference is controlled by a digital preset speed (n024) and is affected by n009.
n009 : Frequency Reference Setting
Method From Digital Operator
Factory setting: 0
Range: 0 or 1
This parameter is only effective when the frequency reference is controlled by a digital preset (n024).
SETTING
DESCRIPTION
0
key must be pressed in order for the drive to accept the frequency reference.
1
key does not have to be pressed.
The Drive responds immediately to the
and
5-15
keys.
5.14 MODBUS CONTROL
The Drive can perform serial communication by using a programmable controller (PLC) and
MODBUS® protocol. Modbus is composed of one master PLC and 1 to 31 (maximum) slave units
(Drives). In serial communication between the master and slaves, the master always starts
transmission and the slaves respond to it.
The master communicates with one slave at a time. Address numbers are assigned to each slave in
advance, and the master specifies an address to communicate with. The slave which receives the
command from the master executes the function, and then responds to the master.
A.
Communication Specifications
• Interface
: RS-485 & RS-422
• Synchronization
:
Asynchronous
• Transmission parameters
:
Baud rate
— Selectable from 2400, 4800,
9600, 19,200 BPS (n154)
— Fixed to 8 bits
— Parity / no parity, even / odd
selectable (n155 )
— Fixed to 1 bit
Data length
Parity
Stop bit
B.
• Protocol
:
Modbus
• Maximum number to units
to be connected
:
31 units
Setting up the Modbus
Terminals S+, S-, R+, and R- are used for modbus communications. A terminating resistor can be
enabled between R+ and R- by setting SW2 (1) to “on.” SW2 is found just above the upper row of
control circuit terminals. SW2 consists of two separate switches, the switch towards the top (labeled
“1”) turns on and off the terminating resistor.
The terminating resistor should only be enabled on the drive farthest away from the master.
RS-422
RS-485
S+
S+
S–
S–
R+
R+
R–
SW2
SW2
TERMINAL RESISTOR (1/2W, 120Ω)
TERMINAL RESISTOR (1/2W, 120Ω)
SW1
1
2
NPN
SW2
OFF
PNP
SW2
R–
5-16
OFF
V
ON
I
SW2
5.14 MODBUS CONTROL
C.
Continued
Sending/Receiving Data
Data that can be sent and received are run/stop commands, frequency reference, fault reset, drive
status, and setting and reading of parameters.
n003 : Operation Method Selection
Factory setting: 0
Range: 0 to 2
Parameter n003 selects where the run/stop commands (sequence) will come from. To be able to provide a run command over the Modbus serial communications link, set this to a data of “2.”
n004 : Reference Selection
Factory setting: 0
Range: 0 to 6
Parameter n004 selects where the frequency reference will come from. To be able to provide a frequency reference over the Modbus serial communications link, set this to a data of “6.”
n050 thru n056 : Multi-function Inputs
(Term. S2-S6)
Data 18: Serial communication/
Digital Operator
Selects operation by serial communication or by external terminal. If the status of this command input
is changed while the drive is running, the selection is ignored until the next time the drive is stopped.
Open
Closed
: Run according to the setting of Operation Method Selection (n003) and
Reference Selection (n004).
: Run by frequency reference and run command from serial
communication.
EXAMPLE:
n003 setting is " 1 ", and n004 setting is " 2 ".
n056 = 18.
TERMINAL S6 Open:
Frequency reference from control circuit terminal FR
and run command from control circuit terminals S1, S2.
TERMINAL S6 Closed: Frequency reference and run command from serial
communication.
5-17
5.14 MODBUS CONTROL
Continued
n152 : Modbus Frequency Resolution
Factory setting: 0
Range: 0 to 3
The frequency resolution from the PLC and in the frequency reference and output
frequency monitor (by communication) are selected with this parameter. The output
frequency resolution of the Drive is 0.1 Hz. Even if the Modbus resolution is
changed to 0.01 Hz in n152 , the value in the hundredths digit of 0.01 Hz of the
received frequency reference is rounded off internally. When 30,000/100% in units
of 0.1% is selected, the value is also rounded off.
Setting
Frequency Resolution
0
0.1 Hz
1
0.01 Hz
2
30000/100%
3
0.1%
n153 : Modbus Slave Address
Factory setting: 0
Range: 0 to 31
Each slave Drive on the same transmission line must be given a unique address.
n154 : Modbus Baud Rate
Factory setting: 2
Range: 0 to 3
Selects the baud rate, as indicated by the following table:
Setting
Baud Rate (BPS)
0
2400
1
4800
2
9600
3
19,200
n155 : Modbus Parity Selection
Factory setting: 2
Range: 0 to 2
Selects the parity, as indicated by the following table:
Setting
Parity
0
Even
1
Odd
2
None
NOTE: To change the values set in n153 thru n155 and enable the new
settings, it is necessary to turn OFF power to the Drive, then turn it ON again.
5-18
5.14 MODBUS CONTROL
Continued
n151 : Modbus Time Out Detection
Factory setting: 1
Range: 0 to 4
If time between Modbus messages exceeds 2.0 seconds, the drive will respond
according to the table below. A setting of " 4 " disables this fault condition.
If communications error exists, drive will respond according to the following table:
Setting
D.
Description
0
Coast to Stop (fault)
1
Ramp to Stop using n020 (fault)
2
Ramp to Stop using n022 (fault)
3
Continue Operation (Alarm)
4
Disabled
Loop Test
The Drive has the ability to perform a serial communications self-check, in the form of a loop test.
Use the following steps to perform a loop test.
1.
With power applied to the Drive set parameter n056 = 35.
2.
Remove power from the Drive and wait for the charge light to go off.
3.
Disconnect all wiring terminals R+, R-, S+, S- & S7.
4.
Install the following wires:
connect S+ to R+
connect S- to Rconnect S7 to SC
5.
Apply power to the Drive.
If the Drive displays a normal frequency reference, the loop test was successful.
If the Drive displays “CE” on the digital operator, the loop test failed and the serial
communications hardware is not functioning correctly. Remove power and recheck all of the
above connections. Re-apply power. If the Drive still displays “CE”, the unit will need to be
replaced.
6.
Remove power from the Drive.
7.
Disconnect the wires installed in step 4.
8.
Re-apply power and program n056 to its previous setting. NOTE: the factory setting of
n056 = 10.
5-19
5.15 MISCELLANEOUS PROTECTIVE FUNCTIONS
n010 : Operator Connection Fault Detection
Selection
Factory setting: 0
Range: 0 or 1
Set this parameter to “1” only if the drive should shut down immediately if the Digital Operator is disconnected while the drive is running. When set to “0”, the fault will not occur until after the drive has
been stopped.
5.16 MOMENTARY POWER LOSS RIDE-THRU
n081 : Momentary Power Loss Ride-thru
Protection
0
1
2
= Disabled (Factory setting)
= Enabled – 2 sec. power loss
ride-thru
= Enabled – indefinite power loss
ride-thru, provided control
power is maintained
The setting of this parameter either enables or disables the ride-thru feature of the Drive. If
disabled, the unit will stop immediately whenever a power loss occurs. If enabled, the Drive will
continue to operate during a momentary power loss of up to 80%, but if the loss exceeds the
identified time period, the Drive will stop.
5.17 MULTI-FUNCTION ANALOG MONITOR OUTPUT (Term. AM & AC)
n065 : Monitor output Selection
Factory Setting: 0
Range: 0 – 1
Analog output AM & AC can be used as a pulse train output (output frequency monitor only).
SETTING
0
1
DESCRIPTION
Analog monitor output
Pulse train output (output frequency monitor)
n066 : Multi-function Analog Output
Factory Setting: 1.00
Range: 0 – 5
The monitor output provides a 0-10 Vdc signal
proportional to either output frequency or output current
between terminals AM & AC:
0 = 0-10 Vdc proportional to output frequency
(10V = 100% of maximum frequency)
1 = 0-10 Vdc proportional to output current
(10V = 100% of drive rated current)
2 = 0-10 Vdc proportional to DC Bus Voltage
(10V = 400 Vdc [800 Vdc])
3 = 0-10 Vdc proportional to motor torque
(10V = motor rated torque)
4 = 0-10 Vdc proportional to output power
(10V = drive capacity (KW))
5 = 0-10 Vdc proportional to output voltage
(10V = n012 (Voltage max))
6 = 0-10 Vdc proportional to frequency reference
5-20
FREQUENCY / CURRENT
METER
(1mA FULL SCALE)
Drive
AM
Analog
output
(0-10 Vdc)
AC
+
–
MULTIFUNCTION
MONITOR
OUTPUT
5.17 MULTI-FUNCTION ANALOG MONITOR OUTPUT (Term. AM & AC)
n067 : Analog Monitor Gain
Continued
Factory Setting: 1.00
Range: 0.01 to 2.00
This constant is used to calibrate the meter connected to terminals AM & AC.
n067 = 0.30
100%
MAX. OUTPUT
FREQUENCY
OR CURRENT.
Factory Setting
(n067 = 1.00)
0
3V
10 V
ANALOG OUTPUT
n150 : Pulse Monitor Output
Frequency Output/Reference
SETTING
0
1
6
12
24
36
40
41
42
43
44
45
Factory Setting: 0
Range: 0, 1, 6, 12, 24, 36, 40 - 45
DESCRIPTION
1140Hz/ Max. frequency (n011)
1F: Output frequency x 1
6F: Output frequency x 6
12F: Output frequency x 12
24F: Output frequency x 24
36F: Output frequency x 36
1140Hz/Max. frequency (n011)
1F: Frequency reference x 1
6F: Frequency reference x 6
12F: Frequency reference x 12
24F: Frequency reference x 24
36F: Frequency reference x 36
At the factory setting of “0” a pulse train frequency of 1440 Hz will be output when output frequency
is 100% .
AM
Pulse
AC
Output frequency
100 %
1440 Hz
Pulse monitor output
When connecting peripheral devices the following load limitations must be considered.
When using output as a sourcing output:
Max output voltage (V)
+5V
+8V
+10V
Load Impedence (K ohms)
1.5K ohms to 3.499K ohms
3.5K ohms to 9.99K ohms
10K ohms or more
When used as a sinking input:
External power supply (v)
Sinking current (mA)
+12VDC +/-5%
16mA or less
5-21
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
The multi-function input terminals can be activated in one of two ways:
Type of input
NPN
(Factory Setting)
Description
A contact closure must be made between a multi-function terminal (S1 to S7) and SC in order
to activate that input.
A DC voltage (+24v, 8mA max. current) must be present on a multi-function input terminal (S1 to S7)
in order to activate that input. NOTE: The minus (-) side of the 24 VDC supply must be connected to SC.
PNP
The multi-function inputs are configured using rotary switch SW1, which is located above the upper
row of control circuit terminals and can be set with a small screwdriver.
NOTE: All power must be removed from the Drive before SW1 can be set.
Drive
External
Contacts
+24VDC
Power Supply(1)
(–)
n050
Multi-function
n051
Input
n052
Terminals
n053
n054 Multi-function
DeviceNet
n055
Input
n056
SW1 set
SC
to NPN
(+)
Drive
External
Contacts
S1
S2
S3
S4
S5
S6
S7
n050
Multi-function
n051
Input
n052
Terminals
n053
n054 Multi-function
DeviceNet
n055
Input
n056
SW1 set
SC
to PNP
S1
S2
S3
S4
S5
S6
S7
External wiring for NPN inputs
External wiring for PNP inputs
(1)
Customer supplied component
n050 :
n051 :
n052 :
n053 :
n054 :
n055 :
n056 :
n056 :
Terminal
Terminal
Terminal
Terminal
Terminal
Terminal
Terminal
Terminal
S1
S2
S3
S4
S5
S6
S7
S7
Function
Function
Function
Function
Function
Function
Function
Function
Factory settings:
n050
n051
n052
n053
n054
n055
n056
2-Wire control
1
2
3
5
6
7
10
3-Wire control
1
2
0
5
6
7
10
These seven parameters select the input signal function for terminals S1 thru S7, and can be independently set.
Parameter settings are checked whenever the enter key is pressed. A parameter set failure (Err) will
occur if any of the following conditions are detected:
•
•
Two parameters contain the same value (n050 thru n056).
Both the Accel/Decel Hold (data 16) and the Up/Down (data 34) functions have been selected.
Table 5-2 lists the possible data setting values and their descriptions for these parameters.
5-22
Continued
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
Table 5-2. n050 thru n056 Data Settings
DATA
FUNCTION
DESCRIPTION*
1
Forward Run/Stop command
(for 2-wire control)
MUST BE SET ONLY IN n052 . Redefines terminals:
S1 = Run; S2 = Stop;
S3 = FWD/REV select
Closed = Run Forward (2-wire control)
Open = Stop
2
Reverse Run/Stop command
(for 2-wire control)
Closed = Run Reverse (2-wire control)
Open = Stop
3
External fault (N.O. contact input)
4
External fault (N.C. contact input)
5
6
7
8
9
Fault Reset
Multi-step frequency
Multi-step frequency
Multi-step frequency
Multi-step frequency
10
Jog selection
Closed = Jog selected See paragraph 5.12
Accel/decel time selection 1
Open = Accel/decel by n019 / n020
Closed = Accel/decel by n021 /n022
See paragraph 5.2
Closed = Shuts off the Drive output
(frequency command is held)
See paragraphs 5.18B, 5.18C
0
11
12
13
FWD/REV selection (for
3-wire control)
Drive trips; Digital Operator displays " EFX ",
where X is 1-7, corresponding to the terminal,
S2-S6, which is receiving the fault input signal
Resets fault, only if RUN command is not present
ref. select
ref. select
ref. select
ref. select
A
B
C
D
External base block
(N.O. contact input)
External base block
(N.C. contact input)
See paragraph 5.11B
Speed Search 1
Closed * = Speed Search operation from
maximum frequency
See paragraph 5.18D
Speed Search 2
Closed * = Speed Search operation from set frequency
See paragraph 5.18D
16
Accel/Decel Hold
See paragraph 5.18F
17
18
Remote/Local selection
Drive operation & reference/
serial communication selection
19
Fast Stop - Fault
(Normally Open Contact)
20
Fast Stop - Alarm
(Normally Open Contact)
21
Fast Stop - Fault
(Normally Closed Contact)
22
Fast Stop - Alarm
(Normally Closed Contact)
See paragraph 5.18A
Open = Operates according to setting of n003 & n004
Closed = Operates from serial communication
See paragraph 5.13
Open = No effect
Closed = If n005 = 0, ramp to stop using n022
Closed = If n005 = 1, coast to stop
Open = No effect
Closed = If n005 = 0, ramp to stop using n022
Closed = If n005 = 1, coast to stop
Open = If n005 = 0, ramp to stop using n022
Open = If n005 = 1, coast to stop
Closed = No effect
Open = If n005 = 0, ramp to stop using n022
Open = If n005 = 1, coast to stop
Closed = No effect
14
15
27
Accel/Decel Time Select 2
Open = No effect
Closed = OH3 alarm
See paragraph 5.2
34
Up/Down function
See paragraph 5.18E (can only be set in n056)
Loop Test (Serial Communications)
See paragraph 5.14D
Can only be set in n056
26
35
Overheat Pre-Alarm OH3
* All contact closures must be maintained, except for speed search, which may
be momentary (see paragraph 5.18D).
5-23
Continued
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
A.
Data 17 : Remote/Local
The use of a Remote/Local command input allows switching between the Digital Operator control
and the external terminal input signals or serial communications, without the need to re-program
n003 or n004. If the status of the Remote/Local command input is changed while the drive is running, the Remote/Local operation selection is not completed until the next time the Drive is stopped.
Closed = Controlled locally (Digital Operator)
NOTE: Parameter n008 determines if the frequency reference will come from the digital
operator potentiometer or parameter n024.
Open = Controlled remotely (external terminal inputs, for Start/Stop and
frequency reference, or serial communications).
NOTE: When a multi-function input terminal is programmed for Local/Remote, the LO/RE LED will
only display local or remote status. Local/Remote cannot be adjusted from the digital operator.
B.
•
•
•
Data 12 : External Base Block by N.O. Contact
When either the Forward Run command or
Reverse Run command is present, and the
external Base Block command is applied
(i.e. contact closed), coast stop is accomplished (after a 20 msec delay), while the
frequency command is maintained.
When the Base Block command is removed,
the drive will recover in a manner similar
to that of Speed Search operation.
EXTERNAL
BASE BLOCK
oo
S6
Drive
SC
0V
When both the Forward Run command
and Reverse Run command are open, and
the external Base Block command is applied
(i.e. contact closed), coast stop is accomplished and after a 20 msec delay the frequency
command is changed to 0Hz. When the Base Block command is removed, the drive will
remain in stopped condition until Forward Run command or Reverse Run command is again
applied.
When external Base Block command is active, a blinking “ b b ” will be displayed
on the Digital Operator.
RUN
RUN
Freq. Cmd
Freq. Cmd
0
Base Block
0
Base Block
V out
V out
0
20msec
0
20msec
(A) Base Block With Run Active
(B) Base Block After Stop Command
5-24
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
C.
Continued
Data 13 : External Base Block by N.C. Contact
Base block operation is the same as described above, except that the Base Block contact must be
open to be recognized.
D.
Data 14 : Speed Search From Max Frequency
Data 15 : Speed Search From Set Frequency
A multi-function input terminal is utilized to activate speed search. When the external speed search
command is closed, the base is blocked for the min. base block time, then the speed search is
made. The operation depends on the set value.
IMPORTANT
Set values 14 and 15 CANNOT be selected in combination.
• When 14 is set, the speed search begins with the maximum frequency.
• When 15 is set, the speed search begins with the frequency command
command that has been set after the search command was received.
RUN
SIGNAL
WITHIN 0.5 SEC
SPEED SEARCH
SPEED COINCIDENCE
POINT
MAX FREQ., OR FREQ.
REF. WHEN SPEED
SEARCH IS INPUTTED
OUTPUT FREQUENCY
MIN.
BASE
BLOCK
TIME
SPEED SEARCH
OPERATION
VOLTAGE AT
SPEED SEARCH
RETURN TO
NORMAL V/f
OUTPUT
OUTPUT VOLTAGE
NOTE: When continuous operation mode at momentary stop function is selected,
the Speed Search command must be enabled.
Speed Search Operation Timing
E.
n101 : Speed Search Deceleration Time
Factory setting: 2.0
Range: 0.0 to 10.0 seconds
Deceleration time during a speed search
n102 : Speed Search Operation Level
Factory setting: 150
Range: 0 to 200%
Speed search starts if the drive’s output current >= speed search operation level.
5-25
Continued
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
F.
Data 34 : Up/Down Function
Programming data " 34 " for n056 (multi-function input terminal) allows the S6 / S7 inputs to be
used for Up/Down frequency setting.
NOTES:
1. Parameter n055 will not be valid when n056 is set to " 34 ".
2. Jog has priority over Up/Down.
3. Up/Down has priority over Multi-step Frequency inputs.
4. Upper limit speed is set by the formula:
n033 (Freq. Ref. Upper Limit)
n011 (Fmax) x
100
5. Lower limit speed is from n034 , Frequency Reference Lower Limit.
6. See section 5.10 for information on the Up/Down hold memory.
EXAMPLE:
Drive
n056 Data 34: Up/Down function
DOWN
o
o
S6
DOWN
S7
UP
UP
o
o
SC
0V
INPUT SIGNAL
Term. S6 Term. S7
DOWN
UP
Open
Open
Open
Closed
Closed
Open
Closed
Closed
FUNCTION
HOLD
DOWN (Frequency command approaches minimum
output frequency or frequency command lower limit,
whichever is larger)
UP (Frequency command approaches frequency
command upper limit)
HOLD
5-26
Continued
5.18 MULTI-FUNCTION INPUT TERMINALS (Term. S1-S7)
FWD RUN
(S6) UP
COMMAND
(S7) DOWN
COMMAND
UPPER
LIMIT SPEED
LOWER
LIMIT SPEED
OUTPUT
FREQUENCY*
D1 H U
H
D
H
U
H
D
D1 H
U
U1 H
D
D1
H
"SPEED AT SET
FREQUENCY"
SIGNAL
* U = UP (Accel) status; D = DOWN (Decel) status; H = HOLD (constant speed) status;
U1 = At Upper Limit Speed; D1 = At Lower Limit Speed
Up/Down Frequency Setting Timing
G. Data 16 : Accel/Decel Hold
By programming data " 16 " into one of the multifunction input parameters ( n050 thru n057 ), one
of the multi-function input terminals (S1 thru S7) becomes a HOLD command input. As long as the
HOLD command is present, accel and decel are in a prohibit state, and the output speed is held at
the level it was at the time the HOLD command was input. When the HOLD command is removed
while the system is still in Run condition, accel or decel will again become active to allow output to
reach set speed. If Stop is initiated while the HOLD command is present, the prohibit state is cancelled and the system enters stop operation.
FWD RUN
HOLD CMD
SPEED REF.
OUTPUT SPEED
HOLD Function Timing
5-27
5.19 MULTI-FUNCTION OUTPUT TERMINALS (Term. MA, MB, MC, P1, P2, PC)
n057 : Contact Output (external
terminals MA, MB, & MC)
n058 : Open Collector Output
(external terminals P1 & PC)
n059 : Open Collector Output
(external terminals P2 & PC)
Drive
o o
o o
MA
MB
MC
A contact, or two different open collector outputs,
can be programmed to change states during any of
the conditions indicated in Table 5-3.
P1
P2
PC
MULTI-FUNCTION
CONTACT OUTPUT
250Vac 1A OR LESS
30Vdc 1A OR LESS
(FACTORY SETTING
IS FOR SIGNAL
DURING OPERATION)
MULTIFUNCTION
OPEN
COLLECTOR
OUTPUTS
48Vdc AT
50mA MAX.
IMPORTANT
If an open collector output is applied to a DC relay, the relay MUST be diode
protected, as shown in the recommended configuration below.
Recommended
Configuration for
DC Relays
48Vdc MAX. *
P1
•
DIODE
P2
PC
C
5-28
▲*
* DC
RELAY
* Customer
supplied
5.19 MULTI-FUNCTION OUTPUT TERMINALS (Term, MA, MB & MC; P1, P2 & PC)
Table 5-3. Multi-function Output Terminals
Description
Set
Value
Condition
Signal Level
0
Fault
Closed = Drive fault has occurred (except CPF00, CPF01)
1
During operation
Closed = Drive is operating
2
Speed at set frequency
Closed = Frequency Reference = output frequency
See paragraph 5.19A
3
Zero Speed
Closed = Drive is at zero Hz.
4
Frequency detection - low
Closed = Output frequency ≤ n095.
See paragraph 5.19B
5
Frequency detection - high
Closed = Output frequency ≥ n095.
See paragraph 5.19C
6
Overtorque detection
(N.O. contact)
Closed = Overtorque detected
See paragraph 5.20
7
Overtorque detection
(N.C. contact)
Open = Overtorque detected
See paragraph 5.20
8
Under torque detection (NO)
Closed if under torque is detected
9
Under torque detection (NC)
Open if under torque is detected
10
Alarm (minor fault)
Closed = Alarm condition is present
11
During coast to stop
Closed = Drive output base block is active; motor is coasting
12
Local/Remote
Open = Frequency and Run Command by ext. input;
Closed = Frequency and Run Command by Digital Operator
13
Operation ready
Closed = Drive is ready for operation (not faulted)
14
Auto-restart
Closed = During auto-restart operation
15
During Undervoltage
Closed = Drive has an undervoltage fault or warning.
16
During Reverse run
Closed = Drive operation in reverse
17
During Speed Search
Closed = Drive performing a speed search
18
Serial communication
Closed = Command from serial communication
20
Frequency reference is missing
Closed if frequency reference is missing
21
Inverter overheating pre-alarm OH3 Closed if drive overheat pre-alarm is input at a Multi-function
Input. Digital operator display is “OH3” (blinking)
5-29
Continued
5.19 MULTI-FUNCTION OUTPUT TERMINALS
n095 : Speed Coincidence Frequency / Frequency
Detection Level
Factory setting: 0.0 Hz
Range: 0.00 to 400.0 Hz
Speed coincidence is used to control an output contact at terminals MA or MB (with respect to terminal MC), or terminals P1, P2 & PC, when selected by n057, n058 and n059.
n057, n058 or n059
Data 2 , 4 or 5
The output contact will close, dependent upon the data programmed into n057, n058 or n059 . See
the appropriate figure below for operation.
A. Speed at Set Frequency
(setting: n057, n058 or n059 = " 2 ")
DETECTION WIDTH
±2Hz
B.
Frequency Detection – Low
(setting: n057, n058 or n059 = " 4 ")
RELEASE WIDTH
±2Hz
RELEASE WIDTH
+2HZ
Frequency
Reference
OUTPUT
FREQUENCY
FREQUENCY
FREQUENCY
AGREED
SIGNAL
FREQUENCY
DETECTION
SIGNAL
ON
C. Frequency Detection – High
(setting: n057, n058 or n059 = " 5 ")
FREQUENCY
DETECTION
LEVEL (Hz)
(n095)
RELEASE WIDTH
—2HZ
OUTPUT
FREQUENCY
FREQUENCY
DETECTION
SIGNAL
ON
5-30
ON
FREQUENCY
DETECTION
LEVEL (Hz)
(n095 )
5.20 OVERTORQUE DETECTION
Overtorque detection is used to compare Drive rated output current/torque with the overtorque
detection level. When the output current is equal to or greater than the defined level, an overtorque
condition exists. This will be indicated as an oL3 fault on the Digital Operator. This feature can be
selected to operate over a wide range of conditions.
n096 : Overtorque Detection
A.
Factory setting: 0
This constant determines whether the overtorque detection function of the Drive is enabled, under
what conditions it will detect for overtorque, and what operation it will perform after detecting an
overtorque.
—
—
Setting
Overtorque
Disabled
Operation
After
Detection
0
Disabled
——
1
Overtorque
Continues
Only at set frequency
2
Overtorque
Coast to stop
Only at set frequency
3
Overtorque
Continues
At all times except during
stopping or DC injection braking
4
Overtorque
Coast to stop
At all times except during
stopping or DC injection braking
Detection
Condition
——
For overtorque detection during accel or decel, set to " 3 " or " 4 ".
For continuous operation after overtorque detection, set to " 1 " or " 3 ". During detection, the Digital Operator displays and “ oL3 ” alarm (blinking).
To stop the drive at an overtorque detection fault, set to " 2 " or " 4 ". At detection, the Digital Operator displays an
" oL3 " fault.
To output an overtorque detection signal, set output terminal function selection (n057, n058 or n059 ) to
" 6 " or " 7 ".
—
—
n098 : Overtorque Detection Level
B.
Factory setting: 160 %
Range: 30 to 200 %
This is the reference point for determining that an overtorque condition exists. Set as a percent of
Drive rated current or as a percent of motor rated torque.
n097 : Overtorque Detection Selection
During Open Loop Vector Control
C.
Setting
Factory setting: 0
Description
0
Detected by motor output torque (as a percentage of motor rated torque)
1
Detected by drive output current (as a percentage of drive rated current)
This parameter is only effective when the drive is in the Open Loop Vector control method.
D.
n099 : Overtorque / Undertorque Detection Time
Factory setting: 0.1 sec.
Range: 0.0 to 10.0 seconds
Determines how long an overtorque condition must exist before another event will occur, e.g. coast
to stop, multi-function output change of state, or oL3 warning or fault display.
5-31
5.20 OVERTORQUE DETECTION
E.
Continued
n057 : Multi-function Output 1
(terminals MA, MB & MC)
n058 : Multi-function Output 2
(terminals P1 & PC)
n059 : Multi-function Output 3
(terminals P2 & PC)
Data 6 or 7 : Overtorque
Detection
A Form-C contact, or an open collector output, can be programmed to change states during an
overtorque detection condition.
EXAMPLE OF OVERTORQUE DETECTION
n096 setting:
n057 setting:
n096 setting:
n099 setting:
2
6
110 %
1.0 s
—
—
—
—
Overtorque enabled, only at set frequency, coast to stop
Output contact programmed for overtorque detection
Level at which overtorque is sensed
Time delay before overtorque event occurs
Detection level
(n098 )
OUTPUT
CURRENT/
TORQUE
Detection
time
(n099)
110%
100%
0
100%
Coast
stop
MOTOR
SPEED
0
RUN
SIGNAL
FAULT
SIGNAL
CONTACT
OUTPUT
(OVERTORQUE
DETECTION)
TERM. MA & MC)
Overtorque Detection Timing Diagram
5-32
5.21 RESET CODES: 2-WIRE, 3-WIRE INITIALIZATION
n001 : Parameter Selection / Initialization
Factory setting: 1
Range: 0 to 9
The following table shows which parameters can be programmed (displayed & changed) or only
displayed when n001 is selected.
Setting
0
Function
n001 can be read and set;
n002 - n179 read only
n001 - n039 can be read and set
n001 - n067 can be read and set
n001 - n113 can be read and set
n001 - n179 can be read and set
n001 - n179 can be read and set – Run Command accepted during Program Mode
Clear Fault Record Only
Not Used
Initialization: 2-Wire control
Initialization: 3-Wire control
1
2
3
4
5
6
7
10
11
CAUTION
Entering a “5” into n001 will allow a RUN command to be accepted even if the drive
is in Program mode (PRGM function LED on) or the LO/RE function LED is on. This condition
may cause the motor to run; equipment damage or personal injury may result.
WARNING
By entering a “10” or an “11” into n001, all parameters in the Drive
will return to their factory settings.
Parameter
n050
n051
n052
n053
n054
n055
n056
Factory Configuration for
2-Wire Control
3-Wire Control
Terminal
S1
S2
S3
S4
S5
S6
S7
1
2
3
5
6
7
10
=
=
=
=
=
=
=
Forward Run
Reverse Run
External Fault (N.O.)
Fault Reset
Multi Step Ref. Cmd. A
Multi Step Ref. Cmd. B
JOG Selection
1
2
0
5
6
7
10
=
=
=
=
=
=
=
Start
Stop
Fwd/Rev Command
Fault Reset
Multi Step Ref. Cmd. A
Multi Step Ref. Cmd. B
JOG Selection
CAUTION
Know your application before using either Initialization function of n001 .
This parameter must be set to " 0 " to " 5 " for operation.
" 10 " = Factory 2-Wire Control Initialization (Maintained RUN Contact)
" 11 " = Factory 3-Wire Control Initialization (Momentary START/STOP Contact)
Entering either Initialization code resets all parameters to factory settings, and
automatically returns n001 setting to " 1 ". If the Drive is connected for 3-Wire
control and this parameter is set to " 10 " (2-Wire Control Initialization), the motor
may run in reverse direction WITHOUT A RUN COMMAND APPLIED. Equipment
damage or personal injury may result.
IMPORTANT
After " 10 " or " 11 " has been entered in n001 , the Motor Rated Current (n036 )
MUST BE REPROGRAMMED to the correct setting for the application.
5-33
5.22 SLIP COMPENSATION
n111 : Slip Compensation Gain
Factory setting: See Table A3-1
Range: 0.0 to 2.5
Slip compensation is used to increase motor speed to account for slip; the drive accomplishes this by
automatically boosting output frequency, with a corresponding boost in output voltage.
The slip compensation gain (n111) determines how much compensation frequency is added. If using
the Drive in Open Loop Vector, typically no adjustment is necessary. The equation below illustrates
how the compensation frequency is generated.
NOTE: A slip compensation gain setting of 0.0 disables slip compensation.
(n110 * n036)
Output Current –
100
* n106 * n111
Compensation Frequency =
n036 – (n110 * n036)
100
Slip Compensation Equation
46.35 Hz actual output
1.35 H
frequency boost
45 Hz command
corresponding
voltage boost
V
f
n110 : Motor No-Load Current
Factory setting: See Table A3-1
Range: 0 to 99%
Motor no-load current (n110 ) is set as a percentage of motor full-load current (n036 ). It is used as
shown in the slip compensation equation.
n112 : Slip Compensation Primary Delay
Time Constant
Factory setting: 2.0 sec.
Range: 0.0 to 25.5 sec.
Parameter n112 can be increased to improve stability or decreased to improve response to load
changes.
n113 : Slip Compensation Selection
During Regen
Factory setting: 0
Range: 0 or 1.
Parameter n113 determines whether the slip compensation gain will be enabled or disabled during
regeneration.
Setting
Description
0
Disabled - No slip compensation will be added when regenerating
1
Enabled - Slip compensation will be added when regenerating
5-34
5.23 STALL PREVENTION
A.
n092 : Stall Prevention During Deceleration
Setting
0
1
Factory setting: 0
Function
Stall prevention during deceleration enabled
Stall prevention during deceleration disabled
Stall prevention during deceleration automatically
adjusts the deceleration rate while monitoring the
DC bus voltage to prevent overvoltage during
deceleration.
Controls the
deceleration
time needed to
prevent overvoltage fault.
FREQUENCY
When the motor load is large or decel time is
short, actual decel time may be longer than the
set value because of stall prevention.
SET
DECEL
TIME
TIME
B.
n093 : Stall Prevention Level During
Acceleration
Factory setting: See Table A3-1
Range: 30 - 200 %
This parameter determines the actual Drive output current level during an acceleration condition. Set in
percent of Drive rated output current.
A setting of " 200 " disables stall
prevention during acceleration. During
acceleration, if the output current
exceeds the value in n093 , acceleration
stops and frequency is maintained.
When the output current goes below the
value set in n093 , acceleration resumes.
In the constant horsepower region
[actual output frequency ≥ max. voltage
frequency (n013 )], the stall prevention
level during acceleration is changed by
the following formula:
MOTOR
CURRENT
Parameter
Constant
n093
n073
Setting
setting
t
OUTPUT
FREQ.
t
Stall prevention level during = Stall prevention level during accel x
accel (constant horsepower)
C.
n094 : Stall Prevention Level At Set Speed
Max. voltage frequency
Actual output frequency
Factory setting: 160%
Range: 30 - 200 %
This parameter determines the actual
Drive output current level while operating
at set speed (frequency). Set in percent
of Drive rated output current (see
Appendix 2).
A setting of " 200 " disables stall
prevention at set speed. During running
at set speed, if the output current exceeds
the value set in n094 , the drive will begin
to decelerate. When the output current
goes below the value set in n094,
acceleration begins, up to the set
frequency.
MOTOR
CURRENT
Constant
Parameter
n074
n094
setting
Setting
t
OUTPUT
FREQ.
t
5-35
5.23 STALL PREVENTION
D.
n115 : Stall Prevention Above Base Speed During Running
Setting
E.
Continued
Factory setting: 0
Range: 0 or 1
Function
0
Disabled (level is based on setting of n094)
1
Enabled (level at Fmax, n011, is n094 x 0.4)
n116 : Stall Prevention During Run, Accel/Decel Time Select
Setting
Factory setting: 0
Range: 0 or 1
Function
0
Follows accel/decel #1 (n019, n020) or accel/decel #2
(n021,n022)
Note: Multi-Function input selectable
1
Follows accel/decel #2 (n021,n022) always
5-36
5.24 STOPPING METHOD
n005 : Stopping Method
Factory setting: 0
Range: 0 to 1
Selects the stopping method suitable for the application.
Setting
A.
Description
0
Deceleration (ramp) to stop
1
Coast to stop
Data 0 : Deceleration to Stop
Upon removal of the FWD (REV) Run
command, the motor decelerates at the
deceleration rate determined by the time
set in Decel Time 1 (n020 ), and DC
injection braking is applied immediately
before stop. If the decel time is too short
or the load inertia is too large, an overvoltage (OV) fault may occur on a stop
command — the decel time must be
increased.
Output Frequency
Min. Output Frequency
(Frequency at DC Injection
Braking Start) (n016 )
DC Injection Braking
Time at Stop (n090 )
(Factory setting: 0.5 s)
Run Command
B.
Decel Time 1
(n020 )
ON
OFF
Data 1 : Coast to Stop
Upon removal of the FWD (REV) Run command, the motor coasts to rest.
Output Frequency
Drive output is shut OFF
when stop command is input
Run Command
OFF
ON
5-37
5.25 THERMAL OVERLOAD PROTECTION
n036 : Motor Rated Current
Factory setting: See Table A3-1
Range: see description
This parameter should be set, in increments of 0.1 A, to the rated current (FLA) value shown on the motor
nameplate; this value MUST BE between 10% and 150% of the drive rated current. If the motor FLA does not
fall within this range, a different Model No. drive must be used.
NOTE: Setting n036 to " 0.0 " disables the motor overload protection
function, regardless of the setting of n037 or n038.
Factory setting: 0
n037 : Electronic Thermal Motor Protection
Setting
Range: 0 to 2
Electronic Thermal Characteristics
0
Short term rating
1
2
Standard rating
Electronic thermal overload protection disabled
n038 : Electronic Thermal Overload Protection
Time Constant
Factory setting: 8
Range: 1 to 60 min.
This parameter sets the electronic thermal overload relay protection time when when 150% of overload is
applied after the motor is operated continuously at rated current.
The Drive protects against motor overload with a UL-recognized, built-in electronic thermal overload relay.
The electronic thermal overload function monitors motor temperature, based on drive output current and time,
to protect the motor from overheating. When the electronic thermal overload trips, an
“ oL1 ” error occurs, shutting OFF the drive output and preventing excessive overheating of the motor.
When operating with one drive connected to only one motor, an external thermal relay is not needed. When
operating several motors with one drive, install a thermal overload relay on each motor.
Standard Rating
Short Term Rating
Cooling Effect
Electronic Thermal
Overload
Current Characteristics
180
Effective when
operated at 60Hz
from a commercial
power supply
60 SEC
SHORT TERM
155
140
CONTINUOUS
RATING
TORQUE 100
(%)
80
“ oL 1 ” error (motor
overload protection)
occurs when
continuously operated
at less than 60Hz at
100% load.
55
Base Frequency
60Hz
(V/f for 60Hz,
230V Input Voltage)
38
0
3 20
60
180
Effective when
operated at low
speed (approx. 6Hz)
120
OPERATION FREQUENCY (Hz)
60 SEC
SHORT TERM
150
CONTINUOUS
RATING
TORQUE 100
(%)
Base Frequency
60Hz
(V/f for 60Hz,
230V Input Voltage)
55
38
0
6
60
120
OPERATION FREQUENCY (Hz)
5-38
Electronic thermal
overload protection not
activated even when
continuously operated
at less than 60Hz at
100% load.
5.26 TORQUE COMPENSATION
n103 : Torque Compensation Gain (KT)
Factory setting: 1.0
Range: 0.0 to 2.5
460
OUTPUT VOLTAGE
( VAC )
Torque Compensation Gain (n103) adjusts how
much the output voltage is boosted when motor
load increases. It is used to compensate for
resistive losses in the motor and the wiring
between the drive and the motor.
AUTO TORQUE BOOST
V/F PATTERN
345
230
PROGRAMMED V/F PATTERN
(NO LOAD)
115
14 V
0
0
1.5 HZ
30
OUTPUT FREQUENCY
( HZ )
Example of Torque Compensation
Operation
n104 : Torque Compensation Time Constant
Factory setting: See Table A3-2
Range: 0.0 to 2.5 (sec)
This parameter adjusts a time delay for the torque compensation gain. Increase to add torque
stability, decrease to improve torque response.
n105 : Torque Compensation Iron Loss
Factory setting: See Table A3-1
Range: 0.0 to 6550 W
This parameter should be adjusted only when motor capacity and drive capacity are different.
n109 : Torque Compensation Limit
Factory setting: 150%
Range: 0 - 250%
This parameter sets the upper voltage limit used by torque compensation.
Except for the most demanding of high starting torque applications, the factory settings of these
parameters will be adequate. The factory settings are set up to match the performance of typical
AC motors.
5-39
60
5.27 V/f PATTERN
The V/f pattern can be tailored to suit your specific application and load characteristics by adjusting
parameters n011 to n017 (see the V/f characteristics figure on the following page).
Table 5-4. Recommended V/f Patterns
Max.
Freq.
Starting
Torque
Load
Type1
n011
(Hz)
n012
(V)3
n013
(Hz)
n014
(Hz)
n015
(V)3
n016
(Hz)
n017
(V)3
50
Normal
VT
50
230
50
25.0
40.2
1.3
9.2
50
High2
VT
50
230
50
25.0
57.5
1.3
11.5
60
Normal
VT
60
230
60
30.0
40.2
1.5
9.2
60
High2
VT
60
230
60
30.0
57.5
1.5
11.5
50
Normal
CT
50
230
50
3.0
17.2
1.5
11.5
50
Medium
CT
50
230
50
2.5
23.0
1.3
13.8
2
50
High
CT
50
230
50
2.5
28.7
1.3
16.1
60
Normal
CT
60
230
60
3.0
17.2
1.5
11.5
60
Medium
CT
60
230
60
3.0
20.7
1.5
13.8
60
High2
CT
60
230
60
3.0
28.7
1.5
23.0
72
Normal
CT
72
230
60
3.0
17.2
1.5
11.5
90
Normal
CT
90
230
60
3.0
17.2
1.5
11.5
120
Normal
CT
120
230
60
3.0
17.2
1.5
11.5
180
Normal
CT
180
230
60
3.0
17.2
1.5
11.5
NOTES:
VT = Variable Torque, typically used for blowers, centrifugal pumps, and fans.
CT = Constant Torque, most other applications. Consult the manufacturer for further assistance.
1
The following conditions must be considered when selecting a V/f pattern:
- Pattern matches the voltage-frequency characteristics of the motor.
- Maximum motor speed.
2 V/f pattern for high starting torque should be selected for:
- Long wiring distance.
- Large voltage drop at start
- AC reactor connected to Drive input or output.
- Use of motor rated below Drive max. output.
3 Voltages shown are for 230V motors; for other motor voltages, multiply all voltage (V) values by (Vmtr/230).
i.e., for a 460V motor, multiply by 460/230 = 2.
5-40
5.27 V/f PATTERN
n011 :
n012 :
n013 :
n014 :
n015 :
n016 :
n017 :
Continued
Frequency – Max. (Fmax)
Voltage – Max. (Vmax)
Frequency – Max. Voltage point (FA)
Frequency – Midpoint (FB)
Voltage – Midpoint (VC)
Frequency – Min. (Fmin)
Voltage – Min. (Vmin)
These seven parameters define the V/f pattern. The illustration below shows how these constants
relate to each other in establishing the custom V/f pattern.
Vmax
(n012 )
OUTPUT
VOLTAGE
VC
(n015 )
Vmin
(n017 )
Fmin
(n016 )
FB
(n014 )
FA
(n013 )
OUTPUT FREQUENCY
V/f Characteristics Set by n011 thru n017
NOTE: To establish a V/f pattern with a straight line from Fmin to FA, set
FB = Fmin. The setting of VC is then disregarded and does not affect the
V/f pattern.
IMPORTANT
The V/f parameter settings are checked each time the ENTER key is
pressed while programming the V/f parameters. A parameter set value
failure (Err ) will occur if any part of the following relationships among
n011 thru n017 is not TRUE:
(a)
Fmax ≥ FA ≥ FB ≥ Fmin
(b)
Vmax ≥ VC ≥ Vmin
5-41
Fmax
(n011 )
5.28 PID CONTROL
The Proportional, Integral and Derivative control function provides closed-loop control, or regulation,
of a system process variable (pressure, temperature, etc.). This regulation is accomplished by
comparing a feedback signal to a setpoint reference, which results in an error signal. The PID
control algorithm then performs calculations, based upon the PID parameter settings (n128 – n138,
n163 and n164), on this error signal. The result of the PID algorithm is then used as the new
frequency reference, or is added to the existing speed reference.
A.
Factory Setting: 0
n128 : PID Control Selection
Setting
0
1
2
3
4
5
6
7
8
Range: 0 to 8
Description
PID Disabled
PID Enabled (D = Feed forward)
PID Enabled (D = Feedback)
PID Enabled, Reference + PID (D = Feed forward)
PID Enabled, Reference + PID (D = Feedback)
Inverse PID Enabled (D = Feed forward)
Inverse PID Enabled (D = Feedback)
Inverse PID Enabled, Reference + PID (D = Feed forward)
Inverse PID Enabled, Reference + PID (D = Feedback)
Using this parameter, PID control can be enabled, and the type of PID control can be selected.
B.
Setpoint Reference Selection
n004 : Reference Selection
Factory Setting: 0
Range: 0 to 6
n024 thru n032: Multi-step Frequency Presets
The frequency reference becomes the PID setpoint.
C.
Factory Settings:
n032 = 6.0
all others = 0.0
Range (each): 0.0 to 400.0 Hz
Feedback Signal Selection
n164: PID Feedback Selection
Factory setting: 0
Range: 0 to 5
Setting
0
1
2
3
4
5
Description
Terminal FR (Voltage 0 – 10V)
Terminal FR (Current 4 – 20 mA)*
Terminal FR (Current 0 – 20 mA)*
Multi-Function Analog Input (0 – 10V)
Multi-Function Analog Input (Current 4 – 20mA)
Pulse Input
* Set SW2(2) to “I” (ON). SW2 consists of two separate slide switches and can be found just above
the upper row of control circuit terminals. The switch towards the bottom (labeled "2") connects a
250Ω resistor from terminal FR to FC when set to the “I” (ON) position (to the right). NOTE: All
power must be removed from the Drive before SW2 can be set. See Figure 1-1 for the location
of SW2.
5-42
5.28 PID CONTROL
D.
Continued
PID Settings
n130: PID Proportional Gain
Factory setting: 1.00
Range: 0.00 to 10.00
Proportional gain is the value by which the error signal is multiplied to generate a new PID
controller output. A higher setting will result in a more responsive system. A lower setting will result
in a more stable system.
n131: PID Integral Time
Factory setting: 1.00
Range: 0.00 to 360.0 sec.
This parameter determines how fast the PID controller will seek to eliminate any steady-state error.
The lower the setting, the faster the error will be eliminated. To eliminate the integral function
entirely, set this parameter to 0.0 seconds. A lower setting will result in a more responsive system.
A higher setting will result in a more stable system.
Factory setting: 100.00
n134: Integral Value Limit (1)
Range: 0.00 to 100.0%
This parameter will limit the effect that the integrator can have. It works whether the PID controller
output is positive or negative. It can also be used to prevent integrator "wind-up".
n132: Derivative Time
Factory setting: 0.00
Range: 0.00 to 10.0 sec.
This parameter can be adjusted to increase system response to fast load or reference changes,
and to reduce overshoot upon startup. To eliminate the differential function entirely, set this
parameter to 0.00 seconds.
Factory setting: 1.0
n163: PID Output Gain (1)
Range: 0.00 to 25.0
This parameter is a multiplier in the output of the PID controller. Increasing this parameter will
make the PID controller more responsive. Be careful not to increase this parameter too much or
the drive / system will become unstable.
Factory setting: 0.0
n133: PID Offset Adjustment (1)
Range: -100.00 to 100.0%
This parameter will add a fixed percentage to the PID output. It can be used to tune out small
system offsets. NOTE: This parameter is set as a percentage of maximum output frequency (n011).
Factory setting: 0.00
n135: PID Output Lag Filter Time (1)
Range: 0.00 to 10.00 sec.
This parameter adds a filter to the PID output to keep it from changing too quickly. The higher the
setting, the slower the PID output will change.
All of these parameters are interactive, and will need to be adjusted until the control loop is properly
tuned, i.e. stable with minimal steady-state error. A general procedure for tuning these parameters
is as follows:
1. Adjust Proportional Gain until continuous oscillations in the Controlled Variable are at a
minimum.
2. The addition of Integral Time will cause the steady-state error to approach zero. The time
should be adjusted so that this minimal error is attained as fast as possible, without making
the system oscillate.
3. If necessary, adjust derivative time to reduce overshoot during startup. The drive’s accel
and decel rate times can also be used for this purpose.
(1)
These parameters are factory set for optimum results for most applications, and generally
don’t need to be changed.
5-43
5.28 PID CONTROL
E.
Continued
Feedback Loss Detection
n136: Feedback Loss Detection Selection
Factory setting: 0
Range: 0 to 2
Setting
0
Description
Feedback loss detection is disabled
1
Feedback loss detection is enabled –
alarm only (drive continues running)
2
Feedback loss detection is enabled –
fault (drive coasts to stop)
n137: Feedback Loss Detection Level (PID)
Factory setting: 0
Range: 0 to 100 %
n138: Feedback Loss Detection Delay Time (PID)
Factory setting: 1.0
Range: 0.0 to 25.5
When feedback loss detection is enabled (n136 = data "1" or "2"), the drive will detect if the
feedback signal falls below the n137 level for more than the n138 delay time and respond according
to the setting of n136.
F.
Multi-Function Input Terminals
n050 thru n056: Multi-function Inputs
(Term. S1 thru S6)
Data 23 : PID Control Off
By programming data "23" into one of the multi-function input parameters (n050 thru n056), the
corresponding multi-function input terminal (S1 thru S6) will disable the PID control. At the same
time the PID setpoint will become the output frequency and the PID’s integrator will reset to zero.
n050 thru n056: Multi-function Inputs
(Term. S1 thru S6)
Data 24 : PID Integral Reset
By programming data "24" into one of the multi-function input parameters (n050 thru n056), the
corresponding multi-function input terminal (S1 thru S6) will immediately reset the integrator’s value
to zero.
n050 thru n056: Multi-function Inputs
(Term. S1 thru S6)
Data 25 : PID Integral Hold
By programming data "25" into one of the multi-function input parameters (n050 thru n056), the
corresponding multi-function input terminal (S1 thru S6) will hold the integrator’s output value.
When the contact is closed (on the Multi-Function Input Terminal), whatever value the integrator is
outputting will remain the same until the contact is opened.
5-44
5.28 PID CONTROL
Continued
PID Block Diagram
5-45
5.29 COPY FUNCTION
The standard digital operator JVOP-140 of the V7 can be used to store (upload) parameters from one
drive, and copy (download) parameters to another drive. The copy function is not available on the
V74X. Parameters are stored in an EEPROM on the digital operator therefore no backup power supply
is necessary. The copy function can be used in most cases except the following.
(1) Different drive types – The user may not copy parameters from a V7 to a J7 drive.
(2) Different voltage class – The user may not copy parameters from a 230V drive to a 460V drive.
(3) Different control mode – The user may not copy parameters from a drive operating in the Volts per
hertz mode (n002=0) to a drive in the Open loop vector mode (n002=1).
The following parameters are not copied when capacities are different.
Parameter No.
n011 to n017
Parameter Name
Parameter No.
Parameter Name
V/f Settings
n108
Motor Leakage Inductance
n036
Motor Rated Current
n109
Torque Boost
n080
Carrier Frequency
n110
Motor No-load Current
n105
Torque Comp Iron Loss
n140
Energy Saving Gain K2
n106
Motor Rated Slip
n158
Motor Code (Energy Saving)
n107
Motor Line-to-line Resistance
Parameters n176, n177, n178 and n179 are not read into the digital operator during a read command.
n176: Parameter Copy Function Selection
Setting
rdy
Factory Setting: rdy
Description
Drive is ready to use Copy Function
rEd
Read (or upload) all parameters from the drive and store them in the Digital Operator
Cpy
Copy (or download) all parameters stored in the Digital Operator to the drive
uFy
Verify that parameters stored in the Digital Operator and the drive are the same
uA
Displays the voltage and kW rating of the drive whose parameters are stored in the
Digital Operator
Sno
Displays the software number of the drive whose parameters are stored in the Digital
Operator
n177:
Parameter Copy Access Selection
Factory Setting: 0
Range: 0 or 1
Setting
Description
0
Reading Disabled
1
Reading Allowed
The Copy Function can be enabled or disabled using parameter n177 – parameters cannot be
uploaded when this parameter is disabled (n177 = 0), preventing the accidental overwriting of
parameters stored in the Digital Operator.
If n177 = 0 and an upload is attempted (n176 = rEd or Cpy), a "PrE" error message will blink on the
Digital Operator display – press DSPL or DATA/ENTER to clear the message.
5-46
5.29 COPY FUNCTION
A.
Read Function (rEd)
The Read function reads the available parameter data from the drive and stores them in a EEPROM in the digital operator. When the Read function is executed the previously stored parameter
data is cleared and replaced with newly read parameters.
Table 5-5. Reading Drive Parameters
DESCRIPTION
Set the highest parameter
access level.
This will allow all parameters
to be viewed and set.
DIGITAL OPERATOR
DISPLAY
KEY SEQUENCE
PRGM
DSPL
Press the
key until the
is lit on the digital operator.
PRGM
LED
PRGM
Press
DATA
ENTER
.
V
PRGM
Press
three times.
PRGM
Press
DATA
ENTER
.
Set Parameter Copy
Access Selection (n177) = 1
PRGM
V
Press and hold
until n177 is displayed on the digital operator.
PRGM
DATA
ENTER
Then press
.
V
PRGM
Use the
display.
key to set a “1” in the
PRGM
Then press
Execute upload (Read)
Using Parameter Read
Function Selection (n176)
DATA
ENTER
.
PRGM
Press the
Then press
V
key once.
DATA
ENTER
PRGM
.
V
Press the
PRGM
key once.
DATA
Press ENTER . “rED” will blink on the display
while reading.
5-47
PRGM
5.29 COPY FUNCTION
B.
Continued
Copy Function (Cpy)
The Copy function writes the parameters stored in the digital operator’s EEPROM into the drives non-volatile memory. The
Copy function is possible only for drives of the same type (i.e. from one GPD 315/V7 to another), voltage rating, and control method (V/f or open loop vector).
Table 5-6. Writing Drive Parameters
DESCRIPTION
Set the highest parameter
access level.
This will allow all parameters
to be viewed and set.
DIGITAL OPERATOR
DISPLAY
KEY SEQUENCE
PRGM
DSPL
Press the
key until the
is lit on the digital operator.
PRGM
LED
PRGM
Press
DATA
ENTER
.
PRGM
V
Press
three times.
PRGM
Press
Execute download (Copy)
Using Copy Function
Selection (n176)
DATA
ENTER
Press the
Then press
.
V
PRGM
key once.
DATA
ENTER
PRGM
.
V
Press the
PRGM
key twice.
DATA
Press ENTER . “CPY” will blink on the
display while writing.
5-48
PRGM
5.29 COPY FUNCTION
C.
Continued
Verify Function (uFy)
Compares the parameter data stored in the operator with the parameter data in the drive. VERIFY
is possible only for drives of the same type (i.e. from one GPD 315/V7 to another), voltage rating,
and control method (V/f or open loop vector).
When the parameters stored in the digital operator match those in the drive, “uFy” will blink in the
display for several seconds, and then "End" will be displayed. When they don’t match “uAE” will be
displayed. Press stop to interrupt the execution of verify, or press Data/Enter to display a list of
parameters that do not match.
Table 5-7. Verifying Drive Parameters
DESCRIPTION
Set the highest parameter
access level.
This will allow all parameters
to be viewed and set.
DIGITAL OPERATOR
DISPLAY
KEY SEQUENCE
DSPL
Press the
key until the
is lit on the digital operator.
Press
DATA
ENTER
PRGM
PRGM
LED
PRGM
.
PRGM
V
Press
three times.
PRGM
Press
Execute upload (Copy)
Using Copy Function
Selection (n176)
DATA
ENTER
.
V
Press and hold
until n176 is displayed on the digital operator.
PRGM
PRGM
Then press
DATA
ENTER
.
PRGM
V
Press the
key three times.
PRGM
DATA
ENTER
Press
. “Vfy” will blink on the display
while verifying.
5-49
5.29 COPY FUNCTION
D.
Continued
Drive Capacity Function (uA)
The Drive Capacity function allows the user to verify that the parameter data stored in the digital
operator are from the same capacity and voltage class as the drive being written too. The voltage
and the drive capacity whose parameters are stored in the digital operator are displayed on the
digital operator. When “uA” is selected and Data/Enter is pressed. The value that is displayed
indicates the voltage and drive capacity in kilowatts. This value can be compared to the drive
specification number on the drive data nameplate.
Model
Display
CIMR-V7*U
E.
MV
20.1
20P1
A001
20.2
20P2
A002
20.4
20P4
A003
20.7
20P7
A005
21.5
21P5
A008
22.2
22P2
A011
23.7
23P7
A017
25.5
25P5
A025
27.5
27P5
A033
40.2
40P2
B001
40.4
40P4
B002
40.7
40P7
B003
41.5
41P5
B005
42.2
42P2
—
43.7
43P7
B009
45.5
45P5
B015
47.5
47P5
B018
Software Number Display
The software number display allows the user to check the software revision number of the
parameter data stored in the digital operator. This value can be compared to the PRG number
on the drive data nameplate.
5-50
5.29 COPY FUNCTION
F.
Continued
Copy Function message list
Operator Description
display
rdy
Drive is ready to perform a Copy Function
rEd
Read selected
Flashing: Read is being performed
Cpy
Writing (COPY) selected
Flashing: Write (Copy) is being performed
uFy
Verify selected
Flashing: Verify is being performed
uA
Drive capacity selected
Sno
Software number displayed
End
Read, Copy or Verify completed
PrE
Flashing: Attempt to execute Read while
parameter Copy Access Selection (n177)
is set to " 0"
rdE
Flashing: Parameter could not be read
properly by the Read function, or, an
under voltage is detected during Read
CSE
Flashing A check sum error occurred in
the parameter data stored in the digital
operator
dpS
ndr
CPE
CyE
F04
Flashing: Parameter data in the drive
and in the digital operator do not match.
(Ex.) Copying from a GPD 315/V7 and
writing to a GPD 305/J7
Flashing: No parameter data is stored
in the digital operator
Flashing: Attempt to execute a Copy
or Verify between different voltage drives
or a different Control Mode
Flashing: An under voltage is detected
during a Copy execution
A check sum error occurs in the
parameter data stored in the inverter
uAE
Flashing: Attempt Execute Verify
between different drive capacities
.FE
Flashing: A communication error has
occurred between the digital operator
and the drive
5-51
Corrective action
Set Parameter n177 to a value of “1”
Confirm that the main circuit power supply
voltage is correct, then re-execute a Read
The parameter data stored in the digital
operator is invalid and cannot be used.
Re-execute Read to store the parameters in
the digital operator
Check to see if the drives are the same type
Execute a Read
Verify Voltage and Control Modes
Confirm that the main circuit power supply
voltage is correct, then-execute a Copy
Initialize the constants. If an error occurs
again, replace the inverter due to a failure of
parameter memory element (EEPROM) in
the drive
Press the Data/Enter key to continue the
execution of Verify. Press stop to interrupt the
execution of Verify
Check the connection between the drive and
the digital operator. If a communication error
occurs be sure to re-execute Read or Copy
5.30
DIGITAL OPERATOR DISPLAY SELECTION
n 0 3 5 : Operator Display Mode
Reference and Indication
Factory setting: 0
Range: 0 to 3999
This parameter determines the scaling of the Digital Operator display, for both Output
Frequency and all Frequency References.
DATA
DATA
DISPLAY
DISPLAY
0
(factory
setting)
Output frequency, in increments of 0.1 Hz.
1
Output frequency, in increments of 0.1 %.
2 to 39
(no. of motor
poles)
Motor synchronous speed (P = 120 x F )
NS
in increments of 1 RPM
(3999 max).
P = no. of motor poles
F = Frequency
NS = motor synchronous speed
NOTE: If motor synchronous speed exceeds
3999 RPM, display holds at 3 9 9 9 .
40
to
39 9 9
Line speed or other parameter.
X X X X
Parameter value at maximum frequency (n 0 1 1 )
(include leading zeroes
if necessary)
Location of decimal point:
_= _XXX
1 = _ X X.. X
2 = _ X.. X X
3 = 0.. X X X
EXAMPLE:
To display Line Speed, based on
54.3 FPM at 60 Hz:
n035 setting = " 15 4 3 "
5-52
5.31 ENERGY SAVING CONTROL
n139:
Energy Saving Selection
(V/f control mode)
Factory Setting: 0
Range: 0 or 1
To enable energy saving control, n139 must be set to "1"
Since the parameters used in energy saving mode have been preset to the optimum values, it is not
necessary to adjust them under normal operation. If the motor characteristics differ greatly from
those of a standard motor, refer to the following description to change the parameters.
A.
Energy Saving Control Mode
n140: Energy Saving Gain
Factory Setting: See Table A3-1
Range: 0.0 to 6550
This gain is used when running in energy saving control mode to calculate the voltage at which
motor efficiency will be greatest, and is set as the output voltage reference. This value is preset to a
typical standard motor value. As energy saving increases, output voltage also increases.
n141: Energy Saving Voltage Lower Limit (60 Hz)
Factory Setting: 50%
Range: 0 to 120%
n142: Energy Saving Voltage Lower Limit (6 Hz)
Factory Setting: 12%
Range: 0 to 25%
n159: Energy Saving Voltage Upper Limit (60 Hz)
Factory Setting: 120%
Range: 0 to 120%
n160: Energy Saving Voltage Upper Limit (6 Hz)
Factory Setting: 16%
Range: 0 to 25%
These parameters are used to set the output voltage upper and lower limits. If the voltage reference
value calculated in the energy saving is below the lower limit or above the upper limit, the lower or
upper limit value is used as the voltage reference value. The lower limit value is set to prevent
stalling at light loads, and the upper limit is set to prevent over-excitation. Set voltage limits at 6Hz
and 60Hz; a value obtained by linear interpolation should be set to any limit values other than 6Hz
or 60Hz. Setting is made as a percentage of motor rated voltage.
*Doubled for 460V Drives
5-53
5.31 ENERGY SAVING CONTROL
B.
Continued
Energy Saving Search Operation
In energy saving control mode, the maximum applicable voltage is calculated using the output
power. However, a temperature change will change the fixed constants and the maximum applicable
voltage may not be obtained.
n144: Voltage limit of tuning
Factory Setting: 0%
Range: 0 or 100%
Limits the range where the voltage can be controlled. Search operation is disabled when n144 is set
to 0.
n145: Step Voltage of tuning to 100 % output voltage
Factory Setting: .5%
Range: 0.1 or 10%
n146: Step voltage of tuning to 5 % output voltage
Factory Setting: .2%
Range: 0.1 or 10%
n143: Time of average KW
Factory Setting: 1 (x24)
Range: 1 to 200 (x24)
Parameter n145 & n146 sets the voltage fluctuation for one cycle of the search operation.
Increasing the values will also increase the fluctuation of the rotation speed. The value calculated by
linear interpolation is set for voltages other than above.
5-54
5.31 ENERGY SAVING CONTROL
Continued
n161: Power Supply Detection Hold Width
Factory Setting: 10%
Range: 0 to 100%
When the power fluctuation is less then this value, the output voltage is held for three seconds and
then the search operation mode is activated.
n162: Power Supply Detection Filter Time Constant
Factory Setting: 5 (x4ms)
Range: 0 to 255 (x4ms)
Decreasing this value increases response during a load fluctuation. However, at low frequency,
unstable operation will occur when this value is set too low.
5.32 MULTI-FUNCTION ANALOG INPUT SELECTION
n077: Multi-Function Analog Input Selection
Factory Setting: 0
Range: 0 to 4
The 2CN input terminal on the digital operator can be used as an auxiliary analog input
(0 –10V or 4 – 20 mA). The Analog Input Connector/Cable Assembly option (DS082) is required for
interface with 2CN on the digital operator.
Setting
Description
0
Multi- Function Analog Input is disabled
1
Auxiliary Frequency Reference (FREF2)
2
Frequency Reference Gain (FGAIN)
3
Frequency Reference Bias (FBIAS)
4
Output Voltage Bias (VBIAS)
1) Auxilary Frequency Reference (n077=1)
2) Frequency Reference Gain (n077=2)
When multi-function analog input
(n004 = 7 or 8) is selected, 2CN on the digital
operator becomes the speed reference input.
If n004 is set to any other data value, the 2CN
auxiliary analog input is determined by the
selection of Command A.
Frequency reference is multiplied by FGAIN,
after frequency reference gain (n060 (terminal
FR) or n074 (terminal RP)) and frequency reference bias (n061 (terminal FR) or n074 (terminal
RP)) are used to calculate a master speed reference input at terminals FR or RP
5-55
5.32 MULTI-FUNCTION ANALOG INPUT SELECTION
Continued
3) Frequency Reference Bias (n077=3)
FBIAS is added to the frequency reference, after
frequency reference gain (n060 (terminal FR) or
n074 (terminal RP)) and frequency reference bias
(n061 (terminal FR) or n075 (terminal RP)) are used
to calculate master speed reference input at
terminals FR or RP
4) Output Voltage Bias (n077=4)
VBIAS is added to output voltage after V/f pattern
is established
n078:
Multi Function Analog Input Signal Selection
Factory Setting: 0
Range: 0 or 1
Setting
Description
0
2CN input terminal (0-10V input)
1
2CN input terminal (4-20mA input)
n079:
Frequency Reference Bias Setting
Factory Setting: 10%
Range: 0 to 50%
This bias is used only for the auxiliary analog input.
5-56
5.33
FREQUENCY REFERENCE LOSS DETECTION
n 0 6 4 : Frequency Reference Loss Detection
Factory setting: 0 (disabled)
Range: 0 or 1
The reference loss detection function is either enabled or disabled, based on the setting of n 0 6 4.
When enabled (data " 1 "), the reference loss detection compares the change in reference with
respect to time. If the reference decreases by 90% in more than 0.4 seconds, the drive will
decelerate to the set reference; if the reference decreases by 90% in less than 0.4 seconds, the
drive will continue to operate at 80% of the output frequency. To regain control of output
frequency, either exceed the set reference (80% of reference) or initiate a STOP command. If Auto
n 0 1 1) x .05, this function is not performed.
Reference is less than Fmax (n
FWD RUN
COMMAND
80%
REF
AUTO
REFERENCE
10%
0.4 SEC
0.4 SEC
80%
FREQ.
GPD 515
OUTPUT
FREQUENCY
Timing Chart
Note: This function applies to frequency references at terminal FR, RP or 2CN (Multi-Function Analog Input).
5.34 UNDERTORQUE DETECTION
Undertorque detection is used to compare Drive output current/torque with the undertorque detection level.
When the output current is equal to or less than the defined level, an undertorque condition exists. This will be
indicated as a UL3 fault on the Digital Operator. This feature can be selected to operate over a wide range of
conditions.
A.
n117 : Undertorque Detection
Factory setting: 0
This constant determines whether the undertorque detection function of the Drive is enabled, under what
conditions it will detect for undertorque, and what operation it will perform after detecting an undertorque.
Setting
Undertorque
Disabled
Operation
After
Detection
0
1
2
3
Disabled
Undertorque
Undertorque
Undertorque
——
Continues
Coast to stop
Continues
4
Undertorque
Coast to stop
5-57
Detection
Condition
——
Only at set frequency
Only at set frequency
At all times except during
stopping or DC injection braking
At all times except during
stopping or DC injection braking
5.34 UNDERTORQUE DETECTION Continued
—
—
—
—
B.
For undertorque detection during accel or decel, set to " 3 " or " 4 ".
For continuous operation after undertorque detection, set to " 1 " or " 3 ". During detection, the Digital Operator
displays and “ UL3 ” alarm (blinking).
To stop the drive at an undertorque detection fault, set to " 2 " or " 4 ". At detection, the Digital Operator displays an
" UL3 " fault.
To output an undertorque detection signal, set output terminal function selection (n057, n058 or n059 ) to
" 8 " or " 9 ".
n118 : Undertorque Detection Level
Factory setting: 10 %
Range: 0 to 200 %
This is the reference point for determining that an undertorque condition exists. Set as a percent of Drive rated
current or as a percent of motor rated torque.
Factory setting: 0.1 sec.
C.
n119 : Undertorque Detection Time
Range: 0.1 to 10.0 seconds
Determines how long an undertorque condition must exist before another event will occur, e.g. coast to stop,
multi-function output change of state, or UL3 warning or fault display.
D.
n057 : Multi-function Output 1
(terminals MA, MB & MC)
n058 : Multi-function Output 2
(terminals P1 & PC)
n059 : Multi-function Output 3
(terminals P2 & PC)
Data 6 or 7 :
Detection
Data 8 or 9 :
Detection
Overtorque
Undertorque
A Form-C contact, or an open collector output, can be programmed to change states during an
overtorque/undertorque detection condition.
EXAMPLE OF OVERTORQUE DETECTION
n096 setting:
n057 setting:
n096 setting:
n099 setting:
2
— Overtorque enabled, only at set frequency, coast to stop
6 — Output contact programmed for overtorque detection
110 %
— Level at which overtorque is sensed
1.0 s
— Time delay before overtorque event occurs
Detection level
(n098 )
OUTPUT
CURRENT/
TORQUE
Detection
time
(n099)
110%
100%
0
Coast
stop
100%
MOTOR
SPEED
0
RUN
SIGNAL
FAULT
SIGNAL
CONTACT OUTPUT
(OVERTORQUE
DETECTION)
TERM. MA & MC)
Overtorque Detection Timing Diagram
5-58
Section 6. FAULT DIAGNOSIS AND CORRECTIVE ACTIONS
6.1 GENERAL
This section describes the alarm and fault displays, explanations for fault conditions and corrective
actions to be taken if the Drive malfunctions.
A failure in the Drive can fall into one of two categories, Alarm or Fault.
A blinking “Alarm” indication is a warning that a Drive trouble condition will soon occur, or that a
programming error has been made. The Drive will continue to operate during an “Alarm” indication.
A blinking “Minor Fault” indication is displayed during less serious faults, or when a problem exists in
the external circuitry. The Drive will continue to operate, and a “Minor Fault” contact will be closed if
a multi-function output is programmed for the condition.
A steady “Major Fault” indication is displayed when the Drive’s Fault relay has tripped. The motor
coasts to a stop, and a fault signal output is present at control circuit terminals 18-20.
: ON
: BLINKING
: OFF
Table 6-1. Alarm Displays and Corrective Actions
Alarm Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Blinking
Blinking
Warning
only.
Fault
contacts
do not
change
state.
Blinking
Blinking
Warning.
Fault
contacts
do not
change
state.
Explanation
Causes and
Corrective Actions
UV (Main circuit low voltage)
Main circuit DC voltage
drops below the low-voltage
detection level while the
drive output is OFF.
230V: Stops at main circuit
DC voltage below
approx. 200V
(160V for singlephase)
460V: Stops at main circuit
DC voltage below
approx. 400 V
Check the following:
• Power supply voltage
• Main circuit power
supply wiring is
connected.
• Terminal screws are
securely tightened.
OV (Main circuit overvoltage)
Main circuit DC voltage
exceeds the over voltage
detection level while the
drive output is OFF.
Detection level: approx.
410V or more (approx.
820V for 460V class).
Check the power supply
voltage.
OH (Cooling fin overheat)
Intake air temperature
rises while the drive
output is OFF.
Check the intake air
temperature.
OH3 (Drive overheat
pre-alarm)
OH3 signal is input.
Release the input of
inverter overheat prealarm signal.
6-1
Table 6-1. Alarm Displays and Corrective Actions - Continued
Alarm Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Blinking
Blinking
Warning
only.
Fault
contacts
do not
change
state.
Blinking
Blinking
Explanation
Causes and
Corrective Actions
CAL (MODBUS
communications waiting)
Correct data has not been
received from the PLC
when the parameter
n003 (operation command
selection) is 2 or
n004 (frequency reference
selection) is 6,
and power is turned ON.
Check communication
devices, and transmission
signals.
OPE (Parameter setting
error when the parameter
setting is performed
through the MODBUS
communications)
OPE1: Two or more values
are set for multifunction input
selection.
(parameters n050 to
n056)
OPE2: Relationship among
V / f parameters is not
correct.
(parameters n011,
n013, n014, n016)
OPE3: Setting value of
electronic thermal
standard current
exceeds 150% of
drive rated current.
(parameter n036)
OPE4: Upper / lower limit
of frequency
reference is reversed.
(parameters n033,
n034)
OPE5: (parameters n083 to
n085)
OPE9: Carrier frequency
setting is incorrect.
(parameter n080)
Check the setting values.
OL 3 (Overtorque
detection)
Motor current exceeded
the preset value in
parameter n098.
Reduce the load, and
increase the accel / decel
time.
SEr (Sequence error)
Drive receives
LOCAL / REMOTE select
command or
communication / control
circuit terminal changing
signals from the multifunction terminal while the
drive output is ON.
Check the external circuit
(sequence).
6-2
Table 6-1. Alarm Displays and Corrective Actions - Continued
Alarm Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Blinking
Blinking
or
Warning
only.
Fault
contacts
do not
change
state.
Blinking
Protective
operation.
Output is
shut OFF
and motor
coasts to
a stop.
Warning.
Fault
contacts do
not change
state.
Causes and
Corrective Actions
BB (External baseblock)
Baseblock command at
multi-function terminal is
active, the drive output
is shut OFF (motor coasting).
Temporary condition is
cleared when input command
is removed.
Check the external circuit
(sequence).
EF (Simultaneous FWD/
REV run commands)
When FWD and REV
run commands are
simultaneously input
for over 500ms, the
drive stops according
to parameter n005.
Check the external circuit
(sequence).
STP (Operator function
stop) is pressed during
running by the control circuit
terminals FWD / REV
command.
The drive stops according
to parameter n005.
Open FWD/REV
command of control
circuit terminals.
STP (Emergency stop)
Drive receives emergency
stop alarm signal.
Drive stops according
to parameter n005.
Blinking
Blinking
Explanation
Check the external circuit
(sequence).
FBL (PID feedback loss
detection)
PID feedback value drops
below the detection level.
When PID feedback loss is
detected, the Drive operates
according to the n136 setting.
When under torque is
detected, drive performs
operation according to the
preset setting of constant
n117.
Check the mechanical
system and correct the
cause, or increase the
value of n137.
UL3 (Under torque detection)
Load (output current or
output torque) is too low.
V/f mode: Drive output
current fell below the preset
value in parameter n118.
Vector mode: Motor current
or torque fell below the
preset value in parameter
n097 and n118.
6-3
Parameter n118 up to the
lowest value allowed for
the machine.
Check the driven machine
and correct the cause of
the fault, or decrease the
value of parameter n118
Table 6-2. Fault Displays and Corrective Actions
Fault Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Explanation
FAN (Cooling fan fault)
Cooling fan is locked.
Blinking
OC (Overcurrent)
Drive output current
momentarily exceeds
approx. 250% of rated
current.
Protective
Operation.
Output is
shut OFF
and motor
coasts to
a stop.
OV (Main circuit overvoltage)
Main circuit DC voltage
exceeds the overvoltage
detection level because
of excessive regenerative
energy from the motor.
Detection level:
230V: Stops at main circuit
DC voltage below
approx. 410V
460V: Stops at main circuit
DC voltage
approx. 820V or more
UV1 (Main circuit low
voltage)
Main circuit DC voltage
drops below the lowvoltage detection level
while the drive output
is ON.
230V: Stops at main circuit
DC voltage below
approx. 200V
460V: Stops at main circuit
DC voltage
approx. 400V or more
6-4
Causes and
Corrective Actions
Check the following:
• Cooling fan
• Cooling fan wiring is not
connected.
• Short circuit
at drive
output side
• Excessive load inertia
• Extremely rapid accel/
decel time
(parameters n019 to n022)
• Special motor used
• Starting motor during
coasting
• Motor of a capacity
greater than the drive
rating has been started.
• Magnetic contactor
open/closed at the
drive output side
• Insufficient decel time
parameters n020 and n022)
• Lowering of minus load
(elevator, etc.)
• Increase decel time.
• Connect optional dynamic
braking resistor.
• Reduction of input
power supply voltage
• Open phase of input supply
• Occurrence of momentary power loss
Check the following:
• Power supply voltage
• Main circuit power
supply wiring is
connected.
• Terminal screws are
securely tightened.
Table 6-2. Fault Displays and Corrective Actions - Continued
Fault Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Explanation
Causes and
Corrective Actions
UV2 (Control power
supply fault)
Voltage fault of control
power supply is detected.
Cycle power.
If the fault remains.
replace the drive.
OH (Cooling fin overheat)
Temperature rise
because of drive
overload operation or
intake air temperature
rise.
• Excessive load
• Improper V/f pattern
setting
• Insufficient accel time
if the fault occurs
during acceleration
• Intake air temperature
exceeding 122°F (50°C)
Check the following:
• Load size
• V/f pattern setting
(parameters n011 to n017)
• Intake air temperature.
Protective
Operation.
Output is
shut OFF
and motor
coasts to
a stop.
OL1 (Motor overload)
Motor overload
protection operates by
built-in electronic thermal
overload relay.
• Check the load size or
V/f pattern setting
(parameters n011 to n017)
• Set the motor rated
current shown on the
nameplate in parameter
n036.
OL2 (Drive overload)
Drive overload
protection operates by
built-in electronic thermal
overload relay.
• Check the load size or
V/f pattern setting
(parameters n011 to n017)
• Check the drive
capacity.
OL3 (Overtorque detection)
V/f mode: Drive output
current exceeded the
preset value in parameter
n098.
Open Loop Vector mode:
Motor current or torque
exceeded the preset
value in parameters
n097 and n098.
When overtorque is
detected, drive performs
operation according to the
preset setting of parameter
n096.
Check the driven
machine and correct the
cause of the fault, or
increase the value of
parameter n098 up to the
highest value allowed for
the machine.
6-5
Table 6-2. Fault Displays and Corrective Actions - Continued
Fault Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Protective
Operation.
Output is
shut OFF
and motor
coasts to
a stop.
Explanation
Causes and
Corrective Actions
EF
(External fault)
Drive receives an
external fault input from
control circuit terminal.
EF0: External fault
reference through
MODBUS
communications
EF1: External fault
input command from
control circuit
terminal S1
EF2: External fault input
command from control
circuit terminal S2
EF3: External fault input
command from control
circuit terminal S3
EF4: External fault input
command from control
circuit terminal S4
EF5: External fault input
command from control
circuit terminal S5
EF6: External fault input
command from control
circuit terminal S6
EF7: External fault input
command from control
circuit terminal S7
Check the external circuit
(sequence).
CPF-00
Drive cannot
communicate with the digital
operator for 5 sec. or
more when power is
turned ON.
Cycle power after checking
the digital operator is
securely mounted.
If the fault remains,
replace the digital operator
or drive.
CPF-01
Transmission fault
occurred for 5 sec or more
when transmission starts
with the digital operator.
Cycle power after checking
the digital operator is
securely mounted.
If the fault remains,
replace the digital operator
or drive.
CPF-04
EEPROM fault of drive
control circuit is detected.
• Record all parameter
data and initialize the
constants. (Refer to
paragraph 5.__ for
constant initialization.)
• Cycle power.
If the fault remains,
replace the drive.
6-6
Table 6-2. Fault Displays and Corrective Actions - Continued
Fault Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
Protective
Operation.
Output is
shut OFF
and motor
coasts to a
stop.
Explanation
Causes and
Corrective Actions
CPF-05
A/D converter fault is
detected.
Cycle power.
If the fault remains,
replace the drive.
CPF-06
Option card connecting fault
Remove power to the
drive.
Check the connection
of the digital operator.
CPF-07
Operator control circuit
(EEPROM or A/D
converter) fault
Cycle power after checking
the digital operator is
securely mounted.
If the fault remains,
replace the digital operator
or drive.
OPR (Operator
connecting fault)
Cycle power.
If the fault remains,
replace the drive.
CE (MODBUS
communications fault)
Check the communication
devices or communication
signals.
PF (Input Phase Loss)
Drive input power supply
has an open phase or has
a large imbalance of voltage.
Check input voltage.
Tighten terminal screws.
Check input voltage.
LF (Output Open Phase)
An open phase occurred
at the Drive output.
Check the wiring to the
motor.
Check motor for phase to
ground short.
Check motor impedance.
RH (Dynamic Braking
Resistor)
6-7
Table 6-2. Fault Displays and Corrective Actions - Continued
Fault Display
Digital
RUN (Green)
Operator
ALARM (Red)
Drive
Status
or
Stops
according to
parameter
__
(OFF)
Explanation
Causes and
Corrective Actions
STP (Emergency stop)
The drive stops
according to parameter
n005 after receiving the
emergency stop fault
signal.
Check the external circuit
(sequence).
FBL (PID feedback loss
detection)
PID feedback value drops
below the detection level.
When PID feedback loss is
detected, the Drive operates
according to the n136 setting.
Check the mechanical
system and correct the
cause, or increase the
value of n137.
Option card
communications fault
Communication fault has
occurred in a mode that
run command and
frequency reference are
set from the communication
option card.
Check the
communication devices
or communication
signals for noise and
power supply.
• Insufficient power
supply voltage
• Control power supply
fault
• Hardware fault
Check the following:
• Power supply voltage
• Main circuit power
supply wiring is
connected.
• Terminal screws are
securely tightened.
• Control sequence.
Replace the drive.
For display/clear of fault history, refer to page 6-8.
Note 1: This fault display only available on drive model numbers CIMR-V7AM25P51, 27P51, 45P51, and 47P51
(MVA025, MVA033, MV015, and MVB018). All other drive ratings display “0L” when a ground fault
condition occurs.
6-8
6.2 Displaying Fault Sequence
When U-09 or n178 is selected, a four-digit box is displayed. The three digits from the right show a
fault description code, and the digit on the left shows the order of fault (from one to four). Number 1
represents the latest fault, and 2,3,4, in ascending order of fault occurrence.
• Example
n®®® ...... 4-digit numbers
n : Order of fault (1 to 4)
®®® : Fault description
“---” is displayed if there is no fault.
(Refer to section 6 for details of fault.)
<
>
• Viewing fault record
Press the ® or ® key to examine the complete fault record.
• Clearing fault record
Set parameter n001 to “6” to clear the fault record. Display returns to “n001” after completion of 6
setting.
Table 6-3.
STEP
STEP
1
Displaying Fault Sequence
DIGITAL OPERATOR
DISPLAY
DIGITAL DISPLAY
OPERATION
PROCEDURE
OPERATION
PROCEDURE
Press
DSPL
until the
MNTR
LED is lit
The digital operator display will read “U-01”
2
Press
U-09
until “U-09” appears on
the display.
3
Press
4
Press
5
ENTER
.
1.EF3
. The display indicates that
this is currently the next
code in the memory register.
Continue pressing
U-01
to display the
other codes in the memory register. After the
last register code is displayed, the sequence
will return to the first code.
2.OV
3.OC
4.– – –
1.EF3
After the fault sequence has been examined, troubleshoot the most recent fault before
entering a Fault Reset command (by Digital Operator STOP/RESET key or external signal
at multi-function input) to prepare the Drive for restart of operation.
Note 1: Parameter initializing (n001=10 or 11) also clears the fault record.
Note 2: Resetting a fault from either the digital operator or multi-function input will not reset the
fault record.
6-9
6-10
Appendix 1. PARAMETER LISTING
The Drive control circuits use various parameters to select functions and characteristics of the
Drive. Changing of parameter settings must be done in the Program mode, or by use of the
Function LEDs, if available (see Section 4).
The following table lists all parameters in numerical order. For each parameter, reference
paragraph(s) in Section 5 are listed (if applicable) where the features of the Drive affected by that
parameter are described.
Table A1-1. V7 Parameters
PARAMETER
n001
n002
n003
Parameter Selection /
Initialization
SETTING RANGE
(AND UNITS)
0: n001 can be read and set;
n002 - n179 read only
1: n001 - n039 can be read and set
2: n001 - n079 can be read and set
3: n001 - n119 can be read and set
4: n001 - n179 can be read and set
5: n001 - n179 can be read and set
Run command accepted during Program mode
6: Clear Fault History Only
7: Not Used
8: 2-wire Initialization (Japan Spec.)
9: 3-wire Initialization (Japan Spec.)
10: 2 wire initialization (USA Spec)
11: 3 wire initialization (USA Spec.)
Control Method Selection
0:
1:
V/f Control
Open Loop Vector
0:
1:
2:
3:
Digital Operator
Terminal
Serial Communication (Modbus)
Option Card
Digital Operator Pot
Digital Operator
Voltage Reference (0 to 10V)
Current Reference (4 to 20 mA)
Current Reference (0 to 20 mA)
Pulse Train Reference
Serial Communications (Modbus)
Multi-Function Analog Input (0 to 10V)
Multi-Function Analog Input (4 to 20 mA)
Option Card
NAME
Operation Method Selection
SETTING
INCREMENT
FACTORY
SETTING
USER
SETTING
PARA.
REF.
1
1
5.21
1
0
2.2
1
1
5.13
1
2
5.11,
5.13
0
5.24
n004
Reference Selection
0:
1:
2:
3:
4:
5:
6:
7:
8:
9:
n005
Stop Method
0:
1:
Ramp to stop
Coast to stop
1
n006
Reverse Prohibit
0:
1:
Reverse Run enabled
Reverse Run disabled1
0
0:
STOP key is effective regardless of
programming of n003
STOP key is effective only when sequence
command (per n003) is from Digital Operator
1
0
5.13
Frequency Reference from digital
operator pot
Frequency Reference from n024
1
0
5.13
1
0
5.13
1
0
5.15
n007
STOP Key Function
n008
Reference Selection Digital Operator
1:
0:
1:
0:
ENTER key must be pressed to write-in
new value
ENTER key does not have to be pressed
to write-in new value
Disabled (operation continues)
Enabled (motor coasts to a stop and fault
is displayed)
n009
Frequency Reference Setting
Method From Digital Operator
n010
Operation Selection
When Digital Operator is
Disconnected
0:
1:
n011
Frequency - Max.
50.0 to 400.0
0.1 (Hz)
60.0
n012
Voltage - Max.
0.1 to 255.0 (230V drive)
0.2 to 510.0 (460V drive)
0.1 (V)
230.0
460.0
n013
Frequency - Max.
Voltage Point
0.2 to 400.0
0.1 (Hz)
60.0
n014
Frequency - Midpoint
0.1 to 399.9
0.1 (Hz)
(Note 2)
n015
Voltage - Midpoint
0.1 to 255.0 (230V drive)
0.2 to 510.0 (460V drive)
0.1 (V)
(Note 2)
n016
Frequency - Min.
0.1 to 10.0
0.1 (Hz)
(Note 2)
Voltage - Min.
0.1 to 50.0 (230V drive)
0.2 to 100.0 (460V drive)
0.1 (V)
(Note 2)
n017
1:
A1-1
5.27
Table A1-1. Drive Parameters - Continued
PARAMETER
SETTING RANGE
(AND UNITS)
SETTING
INCREMENT
FACTORY
SETTING
0.1
0.01
1 (sec)
0
5.2
0.01 (sec)
10.0
5.2
0
5.3
NAME
PARA.
REF.
n018
Accel/Decel Time
Setting Unit
n019
Acceleration Time 1 (Note 4)
0.00 to 600.0
n020
Deceleration Time 1 (Note 4)
or
n021
Acceleration Time 2 (Note 4)
0.0 to 6000
n022
Deceleration Time 2 (Note 4)
(Dependent on n018 setting)
n023
S-curve Selection
0:
1:
2:
3:
n024
Frequency Reference 1 (Note 4)
n025
Frequency Reference 2 (Note 4)
n026
Frequency Reference 3 (Note 4)
n027
Frequency Reference 4 (Note 4)
(< 100 Hz)
0.00
n028
Frequency Reference 5 (Note 4)
or
0.00
n029
Frequency Reference 6 (Note 4)
0.1 (Hz)
0.00
n030
Frequency Reference 7 (Note 4)
(>= 100 Hz)
0.00
n031
Frequency Reference 8 (Note 4)
n032
Jog Frequency Reference (Note 4)
n033
Frequency Reference Upper
Limit
0. to 110
1(%)
100
n034
Frequency Reference Lower
Limit
0. to 110
1(%)
0
0:
0.01 Hz (less than 100 Hz) / 0.1 Hz
Digital Operator
1:
0.1%
1
0
5.30
Display Mode
2 - 39: rpm
40 - 3999: custom
0.1 (A)
(Note 1)
5.25
1
0
n035
0:
1:
USER
SETTING
or
0.1 (sec)
No S-curve
0.2 second
0.5 second
1.0 second
1
6.00
0.00
0.01 (Hz)
0.00 to 400.00
0.1 to 49.5
(Up to 150% of drive rated current)
n037
Electronic Thermal Overload
Protection (for OL1 fault)
0:
1:
2:
n038
Electronic Thermal Overload
Protection Time Constant
1 to 60
n039
Cooling Fan Operation
Selection
Short term rating
Standard rating
Disabled
5.25
1 (min)
8
1
0
1:
Operates only when drive is running
(continues operation for 1 minute after
drive is stopped)
Operates with power applied to drive
Rotate C.C.W.
Rotate C.W. (or opposite direction)
1
0
0:
n040
Motor Rotation
0:
1:
n041
Acceleration Time 3
(Note 4)
0.00 to 600.00
n042
Deceleration Time 3
(Note 4)
or
n043
Acceleration Time 4
(Note 4)
0.0 to 6000.0
n044
Deceleration Time 4
(Note 4)
(Dependent on n018 setting)
n050
Multi-function Input
n052
Multi-function Input
Selection 2 (Terminal S2)
Multi-function Input
Selection 3 (Terminal S3)
5.12
5.9
Motor Rated Current
n051
5.11
0.00
6.00
n036
Selection 1 (Terminal S1)
0.00
0.01 (sec)
or
10.0
5.2
0.1 (sec)
0:
Fwd / Rev command (3 wire control)
[can only be set in n052]
1:
Forward run (2 wire control)
2:
Reverse run (2 wire control)
3:
External Fault (N.O.)
4:
External Fault (N.C.)
5:
Fault Reset
6:
Multi-step speed ref. cmd. A
7:
Multi-step speed ref. cmd. B
8:
Multi-step speed ref. cmd. C
1
1
1
(1)
2
5.18
(2)
A1-2
1
3
(0)
Table A1-1. Drive Parameters - Continued
PARAMETER
n053
Multi-function Input
Selection 4 (Terminal S4)
n054
Multi-function Input
Selection 5 (Terminal S5)
n055
Multi-function Input
Selection 6 (Terminal S6)
n056
SETTING RANGE
(AND UNITS)
NAME
Multi-function Input
Selection 7 (Terminal S7)
n057
Multi-Function Output
Selection 1
(Terminals MA, MB & MC)
n058
Multi-Function Output
Selection 2
(Terminals P1 & PC)
n059
Multi-Function Output
Selection 3
(Terminals P2 & PC)
``
9:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24:
25:
26:
27:
34:
Multi-step speed ref. cmd. D
JOG Selection
Accel/Decel time change cmd.
External Base Block (N.O.)
External Base Block (N.C.)
Speed search from max. freq.
Speed search from set freq.
Accel/Decel hold command
Remote/Local selection
Serial Communication / control ckt.
selection
Fast Stop - Fault (N.O.)
Fast Stop - Alarm (N.O.)
Fast Stop - Fault (N.C.)
Fast Stop - Alarm (N.C.)
PID control off
I value reset (PID)
I value hold (PID)
Over Heat Pre-alarm OH3
Accel/Decel Time Select 2
Up
0: Fault
1: During running
2: Speed Agree
3: Zero Speed
4: Frequency detection 1
5: Frequency detection 2
6: Overtorque detection (N.O.)
7: Overtorque detection (N.C.)
8: Undertorque Detection (N.O.)
9: Undertorque Detection (N.C.)
10: Minor Fault
11: During Base Block
12: Local / Remote
13: Ready
14: During auto restart
15: During undervoltage
16: During reverse run
17: During speed search
18: Serial Comm. Controlled
19: PID feedback loss
20: Frequency Reference Loss Detect (N.O.)
21: Overheat Pre-alarm OH3 (N.O.)
SETTING
INCREMENT
FACTORY
SETTING
1
5
(5)
1
6
(6)
1
7
(7)
USER
SETTING
PARA.
REF.
5.18
1
10
(10)
1
0
1
1
5.19
1
2
n060
Analog Frequency Reference
Gain (term. FR to FC) (Note 4)
0 to 255
1 (%)
100
n061
Analog Frequency Reference
Bias (term. FR to FC) (Note 4)
-100 to 100
1 (%)
0
Analog frequency reference
filter time constant
(term. FR to FC) (Note 4)
0.00 to 2.00
0.01 (sec)
0.10
n064
Frequency Reference Loss
Detection
0:
1:
1
0
5.33
n065
Monitor Output0:
Selection
Analog monitor output
1: Pulse monitor output
1
0
5.17
1
0
5.17
n062
5.8
No Detection
Continue to run at 80% of max. frequency
0:
Output frequency (10V = 100% Fmax)
1:
Output Current (10V = 100% drive
2:
DC Bus Voltage
3:
Motor Torque
rated current)
n066
Multi-function Analog Output
(Terminals AM & AC)
(10V = 400 VDC [800 VDC])
(10V = Motor rated torque)
4:
5:
6:
Output Power
(10V = Drive Capacity kW)
Output Voltage 10V = n012 (voltage max)
Frequency Reference
n067
Analog Monitor Gain (Note 4)
0.00 to 2.00
0.01
1.00
n068
Analog Frequency Reference
Gain (CN2, Voltage Ref Input)
-255 to 255
1%
100
n069
Analog Frequency Reference
Bias (CN2, Voltage Ref Input)
-100 to 100
1%
0
5.32
A1-3
Table A1-1. Drive Parameters - Continued
PARAMETER
SETTING RANGE
(AND UNITS)
NAME
SETTING
INCREMENT
FACTORY
SETTING
0.01 s
0.10
USER
SETTING
PARA.
REF.
n070
Analog Frequency Reference
Filter Time Constant
(CN2, Voltage Ref Input)
n071
Analog Frequency Reference
-255 to 255
Gain (CN2, Current Ref Input)
1%
100
n072
Analog Frequency Reference
-100 to 100
Bias (CN2, Current Ref Input)
1%
0
n073
Analog Frequency Reference
Filter Time Constant
(CN2, Current Ref Input)
0.00 to 2.00
0.01 s
0.10
n074
Pulse Train Frequency
Reference Gain
-255 to 255
1%
100
n075
Pulse Train Frequency
Reference Bias
-100 to 100
1%
0
n076
Pulse Train Frequency Reference Filter Time Constant
0.00 to 2.00
0.01 s
0.10
Multi-Function Analog
Input Selection
0:
1:
2:
3:
4:
Multi-Function analog input disabled
Aux. Frequency reference
Frequency gain
Frequency bias
Voltage bias
1
0
n078
Multi-Function Analog Input
Signal Selection
0:
1:
0 - 10V
4 - 20 mA
1
0
n079
Multi-Function Analog Input
Bias Setting
0 to 50
1%
10
n080
Carrier Frequency
1 to 4 (x 2.5 kHz)
7 to 9 (synchronous)
1
3
5.5
1
0
5.16
1
0
5.4
n077
0.00 to 2.00
0:
1:
Not Provided
Continuous operation after power
recovery within 2 sec.
Continuous operation after power
recovery within control logic time
(no fault output)
Momentary Power Loss
Ride-through Method
n082
Number of auto restarts
attempts
0 to 10
n083
Prohibit Frequency 1
0.00 to 400.0
0.01 (Hz)
or 0.1 (Hz)
0.00
n084
Prohibit Frequency 2
0.00 to 400.0
0.01 (Hz)
or 0.1 (Hz)
0.00
n085
Prohibit Frequency 3
0.00 to 400.0
0.01 (Hz)
or 0.1 (Hz)
0.00
n086
Prohibit Frequency Deadband 0.00 to 25.50
0.01 (Hz)
0.00
n089
DC Injection Current
0 to 100
n090
DC Injection Time at stop
n091
1 (%)
50
0.0 to 25.5
0.1 (sec)
0.0
DC Injection Time at start
0.0 to 25.5
0.1 (sec)
0.0
n092
Stall Prevention During
Deceleration
0:
1:
1
0
n093
Stall Prevention During
Acceleration
30 to 200
1 (%)
170
n094
Stall Prevention Level During
Running
30 to 200
1 (%)
160
n095
Frequency Detection Level
0.00 to 400.0
0.01 (Hz)
or 0.1 (Hz)
0.00
Enabled
Disabled
A1-4
5.11
5.32
n081
2:
5.32
5.6
5.7
5.23
5.19
Table A1-1. Drive Parameters - Continued
PARAMETER
SETTING RANGE
(AND UNITS)
0:
1:
2:
n096
SETTING
INCREMENT
FACTORY
SETTING
Detection Disabled
Detect only at set frequency;
operation continues
Detect only at set frequency;
coast to stop
Detect during all frequency conditions;
operation continues
Detect during all frequency conditions;
coast to stop
1
0
Detected by output torque
Detected by output current
1
0
NAME
Overtorque Detection (OL3)
3:
4:
USER
SETTING
PARA.
REF.
5.20
Overtorque Detection
Selection (OL3)
0:
1:
n098
Overtorque Detection
Level (OL3)
30 to 200
1 (%)
160
n099
Overtorque Detection
Delay Time (OL3)
0.1 to 10.0
0.1 (sec)
0.1
n100
Up/Down Hold
Memory
0:
1:
1
0
5.10
n101
Speed Search
Deceleration Time
0.0 to 10.0
0.1 (sec)
2
5.18
n102
Speed Search Operation
Level
0 to 200%
1 (%)
150
5.18
n103
Torque Compensation Gain
(Note 4)
0.0 to 2.5
0.1
1.0
n104
Torque Compensation
Time Constant
0.0 to 25.5
0.1 (sec)
(Note 2)
n105
Torque Compensation
Iron Loss
0.0 to 6550
0.1 (W) or
1 (W)
(Note 1)
n106
Motor Rated Slip (Note 4)
0.0 to 20.0
0.1 (Hz)
(Note 1)
n107
Motor Line-to-line
Resistance
0.000 to 65.50
0.001 (ohm)
(Note 1)
n108
Motor Leakage
Inductance (Note 1)
0.00 to 655.0
0.01 (mH)
or 0.1 (mH)
(Note 1)
n109
Torque Compensation
Limit
0 to 250
1 (%)
150
5.26
n110
Motor No-load Current
0 to 99
1 (%)
(Note 1)
2.2
n111
Slip Compensation Gain (Note 4)
0.0 to 2.5
0.1
(Note 2)
n112
Slip Compensation Primary
Delay Time
0.0 to 25.5
0.1 (sec)
(Note 2)
n113
Slip Compensation Selection
During Regeneration
0:
1:
Disabled
Enabled
1
0
0:
Disabled
(level is based on setting of n094)
Enabled
(level at Fmax is n094 x 0.4)
1
0
Follows acc/dec #1 (n019, n020)
or acc/dec #2 (n021, n022)
Note: Multi-Function input selectable
Follows acc/dec #2 (n021, n022)
always
1
0
1
0
n097
n115
Stall Prevention Above Base
Speed During Run
1:
0:
n116
Stall Prevention During Run,
Accel/Decel Time Select
1:
0:
1:
n117
Undertorque Detection
Select (UL3)
2:
3:
4:
Disabled
Enabled
Undertorque detection disabled
Detected during constant speed running.
Operation continues after detection
Detected during constant speed running.
Operation stops during detection
Detected during all frequency conditions.
Operation continues
Detected during all frequency conditions.
coast to stop
n118
Undertorque Detection
Level (UL3)
0 to 200%
Inverter rated current = 100%; if n097 = 0
(detection by torque); motor rated torque
becomes 100%
n119
Undertorque Detection
Time (UL3)
0.1 to 10.0
n120
n121
n122
n123
n124
n125
n126
n127
Frequency Reference 9 (Note 4)
Frequency Reference 10 (Note 4)
Frequency Reference 11 (Note 4)
Frequency Reference 12 (Note 4)
Frequency Reference 13 (Note 4)
Frequency Reference 14 (Note 4)
Frequency Reference 15 (Note 4)
Frequency Reference 16 (Note 4)
A1-5
2.2, 5.22
5.22
5.23
5.34
1(%)
0
0.1 (sec)
0.1
0.01 (Hz)
(< 100 Hz)
or
0.1 (Hz)
(>= 100 Hz)
0.00 to 400.00
5.26
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
5.11
Table A1-1. Drive Parameters - Continued
PARAMETER
SETTING RANGE
(AND UNITS)
PID Control Selection
n129
n130
n131
n132
n133
n134
n135
PID Feedback Gain (Note 4)
PID Proportional Gain (Note 4)
PID Integral Time (Note 4)
PID Derivative Time (Note 4)
PID Offset Adjustment (Note 4)
Integral Value Limit (Note 4)
PID Output Lag Filter Time (Note 4)
n136
Feedback Loss
Detection Selection
n138
n139
n140
n141
n142
n143
n144
n145
n146
n149
n150
n151
FACTORY
SETTING
1
0
0.01
0.1
0.1 s
0.01
1%
1%
0.1 s
1.00
1.0
1.0
0.00
0
100
0.0
1
0
1%
0
0.1 s
1.0
1
0
0.1 or 1
(Note 1)
0 to 120
1%
50
0 to 25
1%
12
1 to 200
1
(x 24 ms)
1
(24 ms)
1 to 100
1%
0
0.1 to 10.0
0.1%
0.5
0.1 to 10.0
0.1%
0.2
100 to 3300
1 (x 10 Hz)
3072
(30,720 Hz)
5.11
0, 1, 6, 12,
24, 36, 40,
41, 42, 43,
44, 45
0
5.17
1
0
5.14
0:
1:
2:
3:
4:
5:
6:
7:
n128
n137
SETTING
INCREMENT
NAME
(
Feedback Loss
Detection Level
Feedback Loss
Detection Time
Energy Saving Selection
(Note 2)
(Energy Saving)
Energy Saving Gain
K2 (Energy Saving)
Energy Saving Voltage
Lower Limit at 60 Hz
(Energy Saving)
Energy Saving Voltage
Lower Limit at 6 Hz
(Energy Saving)
Time of Average kW
(Energy Saving)
Voltage Limit of Tuning
(Energy Saving)
Step Voltage of Tuning to
100% Output Voltage
(Energy Saving)
Step Voltage of Tuning to
5% Output Voltage
(Energy Saving)
Pulse Train Input Scaling
Pulse Monitor Output
Frequency Selection
Modbus Time Out
Detection
)
PID control disabled
D = Feed Forward
D = Feedback
Reference + PID (D = Feed Forward)
Reference + PID (D = Feedback)
Inverse PID - D = Feed Forward
Inverse PID - D = Feedback
Inverse PID - Reference + PID
(D = Feed Forward)
8: Inverse PID - Reference + PID
(D = Feedback)
0.00 to 10.00
0.00 to 25.00
0.00 to 360.00
0.00 to 2.50
-100 to 100
-100 to 100
0.0 to 10.0
0: Disabled
1: Enabled - Alarm (operation continues)
2: Enabled Fault (coast to stop)
0 to 100
0.0 to 25.5
0: Energy saving disabled
1: Energy saving enabled
Note: Energy saving becomes enabled by
V/f control mode
0.00 to 6550
USER
SETTING
PARA.
REF.
5.28
5.31
Output Frequency Monitor:
0: 1440 Hz / Max. output frequency
1: 1f output
6: 6f output
12: 12f output
24: 24f output
36: 36f output
Frequency Reference Monitor:
40: 1440Hz / Max. output frequency
41: Frequency reference * 1
42: Frequency reference * 6
43: Frequency reference * 12
44: Frequency reference * 24
45: Frequency reference * 36
0: Fault - Coast to stop
1: Fault - Ramp to stop (n020)
2: Fault - Ramp to stop (n022)
3: Alarm - operation continues
4: Disabled
A1-6
Table A1-1. Drive Parameters - Continued
PARAMETER
n152
Modbus Frequency
Reference Unit2:
n153
Modbus Slave Address
n154
Modbus Baud Rate
n155
Modbus Parity Selection
n156
Modbus Send Waiting Time
n157
Modbus RTS control
n158
n163
Motor Code
Energy Saving Voltage
Upper Limit At 60 Hz
(Energy Saving)
Energy Saving Voltage
Upper Limit At 6 Hz
(Energy Saving)
Power Supply Detection
Hold Width (Energy Saving)
Power Supply Detection
Filter Time Constant
PID Output Gain
n164
PID Feedback Selection
n159
n160
n161
n162
n173
Input Phase Loss
Detection Level
Input Phase Loss
Detection Time
Output Phase Loss
Detection Level
Output Phase Loss
Detection Time
DC Injection P Gain
n174
DC Injection I Time
n166
n167
n168
n169
n175
n176
n177
n178
n179
Note
Note
Note
Note
1:
2:
3:
4:
SETTING RANGE
(AND UNITS)
NAME
Reduce Carrier
at low speed selection
Digital Operator Parameter
Copy Function Selection
Digital Operator
Parameter copy
Access Selection
Fault History
Software Number
0: 0.1 Hz
1: 0.01 Hz
30000/100%
3: 0.1 %
0 to 32
0: 2400 bps
1: 4800 bps
2: 9600 bps
3: 19200 bps
0: even parity
1: odd parity
2: no parity
10 to 65
0: RTS control enabled
1: RTS control disabled 1
(RS-422A 1 to 1 communication)
0 to 70
SETTING
INCREMENT
FACTORY
SETTING
1
0
1
0
1
2
1
2
1 (msec)
10
USER
SETTING
PARA.
REF.
5.14
0
1
(Note 1)
0 to 120
1%
120
0 to 25
1%
16
5.31
0 to 100
0 to 255
0.0
0:
1:
2:
3:
to 25.0
Terminal FR (Voltage 0 - 10V)
Terminal FR (Current 4 - 20mA)
Terminal FR (Current 0 - 20mA)
Multi-Function Analog Input
(Voltage 0 - 10V)
4: Multi-Function Analog Input
(Current 4 - 20mA)
5: Pulse input
0 to 100 (%)
0 to 255 (sec)
0 to 100 (%)
0.0 to 2.0 (sec)
1%
10
1
(x 4 ms)
0.1
5
(20 ms)
1.0
1
0
1%
0
1 sec
0
1%
0
0.1 sec
0
1 to 999
1 (0.001)
1 to 250
1 (4ms)
83 (0.083)
25
(100ms)
0:
1:
Disabled
Carrier Frequency reduced to 2.5kHz
when Fout <= 5Hz & Iout >= 110%
rdy : READY status
rEd: READ executes
Cpy: COPY executes
vFy: VERIFY executes vFy
vA: Inverter capacity display
Sno: Software No. displaySno
0:
1:
Read disabled
Read allowed
(Note 3)
(Note 3)
1
0
5.5
rdy
5.29
1
0
5.29
N/A
N/A
N/A
N/A
6.2
4.4
rdy
rEd
Cpy
vA
Factory setting differs depending on V7 capacity. See Appendix 3-1.
Factory setting differs depending on control method selected (n002). See Appendix 3-1.
n178 and n179 are display only parameters
Parameter can be changed while V7 is operating.
A1-7
5.28
A1-8
Appendix 2. SPECIFICATIONS
Table A2-1. Standard Specifications
SECTION A. Model No. Related Specifications
Physical
Characteristics
Power
Supply
Output
Characteristics
230V
Model
Class
CIMR-V7*
MV
Max. applicable motor
output HP(1)
Drive capacity (kVA)
Rated Output Current (A)
Rated Input Current (A)
Max. Output Voltage (V)
Max. Output Frequency (Hz)
Rated Input Voltage and
Frequency
Allowable voltage fluctuation
Allowable frequency fluctuation
NEMA 1
Cooling Method
(QTY)
NEMA 4
20P1
A001
20P2
A002
20P4
A003
20P7
A005
21P5
A008
22P2
A011
23P7
A017
2
3
5
1/8
1/4
1/2
3/4&1
0.3
0.8
1.1
0.6
1.6
1.8
1.1
3.0
3.9
200 to
1.9
3.0
4.2
6.7
5.0
8.0
11.0
17.5
6.4
11.0
15.1
24.0
230V (proportional to input voltage)
400 Hz (programmable)
25P5
A025
Speed Regulation
Frequency setting resolution
Output frequency resolution
Overload capacity
Frequency Reference Signal
Accel/Decel Time
Braking Torque
V/f characteristics
27P5
A033
7.5
10
9.5
25
33.0
13
33 (5)
39.6
3-phase. 200 to 230 V, 50/60 Hz
-15% to +10%
±5%
fan
fan
self
fan
self
self
self
self
self
self
---
40P2
B001
40P4
B002
40P7
B003
--
1/2
3/4
1&2
----
0.9
1.2
1.6
1.4
1.8
2.4
380 to
fan
fan
fan
fan
fan(2)
self
fan(2)
self
41P5
B005
42P2
--
43P7
B009
47P5
--
3
3
5
45P5
B015
7.5 &
10
11
14.8
19.6
16 (6)
21 (6)
27.8 (6)
fan(2)
self
fan(2)
self
2.6
3.7
4.2
7
3.4
4.8
5.5
8.6
4.7
7.0
8.1
12.0
460V (proportional to input voltage)
400 Hz (programmable)
15
(6)
3-phase. 380 to 460 V, 50/60 Hz
---
self
self
self
self
-15% to +10%
±5%
self
fan
self
fan
fan
fan
fan
fan
SECTION B. All Drives
Control method
Frequency control range
Frequency accuracy
(temperature change)
Control Characteristics
Physical
Characteristics
Power
Supply
Output
Characteristics
460V
Model
Class
CIMR-V7*
MV
Max. applicable motor output
HP(1)
Drive capacity (kVA)
Rated Output Current (A)
Rated Input Current (A)
Max. Output Voltage (V)
Max. Output Frequency (Hz)
Rated Input Voltage and
Frequency
Allowable voltage fluctuation
Allowable frequency fluctuation
NEMA 1
Cooling Method
(QTY)
NEMA 4
Sine wave PWM (V/f Control or Open Loop Vector)
0.1 to 400 Hz
Digital command: ±0.01% (14 to 122°F, -10 to +50°C)
Analog command: ±0.5% (77°F ± 18°F, 25°C ± 10°C)
Open Loop Vector: ±0.2%
V/Hz Mode: ±0.5% – 1% with Slip Compensation
Digital Operator reference: 0.01 Hz (< 100Hz)
0.1 Hz (100Hz or more)
Analog reference: 0.06Hz/60Hz (1/1000)
0.01 Hz
150% of rated output current for 1 minute
0 to 10VDC (20kΩ), 4 to 20mA (250Ω), 0 to 20mA (250Ω) pulse train input,
Digital Operator Pot
0.01 to 6000 sec.
(accel/decel time are independently programmed)
Short-term average deceleration torque (2)
0.2kW: 150%
0.75kW: 100%
1.5kW: 50%
2.2kW or more: 20%
Continuous regenerative torque: Approx. 20% (150% with
optional braking resistor, braking transistor built-in)
Custom V/f pattern
See notes at end of table.
(table continued on next page)
A2-1
Table A2-1. Standard Specifications (Continued)
SECTION B. All Drives (Continued)
Motor overload protection
Electronic thermal overload relay
Instantaneous overcurrent
Motor coasts to stop at approx. 250%
of drive current
Protective Functions
Overload
Motor coasts to stop after 1 min. at 150% of
drive rated current (7)
Overvoltage
Motor coasts to stop if DC bus voltage exceeds
410VDC (230V), 820VDC (460V)
Undervoltage
Motor coasts to stop when DC bus voltage is
210VDC or less (230V), 400VDC or less (460V)
Momentary Power Loss
The following operations are selectable:
• Not provided (stops if power loss is 15 ms or longer)
• Automatic restart at recovery from 0.5 sec. power loss
• Automatic restart
Heatsink overheat
Stall prevention level
Ground fault
Power charge indication
Protected by electronic circuit
Independently programmable during accel and
constant-speed running. Selectable during decel.
Protected by electronic circuit (overcurrent level)
ON until the DC bus voltage becomes 50V or less.
RUN lamp says ON or digital operator LED stays ON.
(Charge LED is Provided for 400V)
Cooling Fan Fault
Protected by electronic circuit
Output signals
Multi-function input
Multi-function output
Analog monitor
Standard functions
Display
Other Functions
Input signals
Run/stop input
Status indicator LEDs
Digital Operator
Terminals
2-Wire or 3-Wire
Seven of the following input signals are selectable:
Forward/reverse run (3-Wire sequence), fault reset,
external fault (NO/NC contact input), multi-step speed operation,
Jog command, accel/decel time select,
external baseblock (NO/NC contact input, speed search command,
accel/decel hold command, LOCAL/REMOTE selection,
communication/control circuit terminal selection,
emergency stop fault emergency stop alarm
Following output signals are selectable
(1 NO/NC contact output, 2 photo-coupler outputs):
Fault, running, zero speed, at frequency, frequency detection
(output frequency ≤ or ≥ set value), during overtorque detection,
during undervoltage detection, minor error, during baseblock, operation mode,
inverter run ready, during fault retry, during UV, during speed search,
data output through communication
0 to +10VDC output, programmable for output frequency or output current
Open Loop Vector Control, full-range automatic torque boost, auto restart,
upper/lower frequency limit, DC injection braking current/time at start/stop,
frequency reference gain/bias, prohibited frequencies,
analog meter calibrating gain, S-curve accel/decel, slip compensation,
MODBUS communications (RS485/422, Max. 19.2K bps),
frequency reference from digital operator pot
RUN and ALARM LEDs provided as standard
Monitors frequency reference, output frequency,
output current, FWD/REF selection
Screw terminals for both main circuit and control circuit
Wiring distance between
328 ft (100 m) or less (3)
drive and motor
Enclosure
Open Type/NEMA type 1/NEMA type 4X/12
Cooling method
Self-cooling/cooling fan
Environmental
conditions
Ambient temperature
14 to 104°F (-10 to 40°C)
Humidity
95% RH or less (non-condensing)
Storage temperature (4)
Location
-4 to 140°F (-20 to 60°C)
Indoor (free from corrosive gases or dust)
Elevation
3,280 feet (1,000 m) or less
Vibration
Up to 1G, at less than 20 Hz;
up to 0.2G, at 20 to 50 Hz
NOTES:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Based on an N.E.C. standard 4-pole motor for max. applicable motor output.
Shows deceleration torque for an uncoupled motor decelerating from 60 Hz in 0.1 seconds.
Contact Yaskawa for wiring distances greater than 328 ft. (100 m).
Temperature during shipping (for short periods of time).
On NEMA type 4X/12 model only, maximum continuous rating of 30.8 A is 40 degrees C maximum ambient. For 33.0 A maximum
continuous rating, maximum ambient is 32 degrees C.
Applies to NEMA type 4X/12 model only.
On Model 47P5 NEMA type 4X/12 (21A), overload is 120% for 1 minute.
A2-2
Appendix 3. CAPACITY & CONTROL METHOD
RELATED PARAMETERS
The factory setting of certain parameters change with drive rating and control method selected. The
following two tables list the parameters and how they change.
Table A3-1. Parameters Related to Drive Capacity
Model
CIMR-V7*U
MV
n036
n105
n106
n107
n108
n110
n140
n158
20P1
A001
0.6
1.7
2.5
17.99
110.4
72
481.7
0
20P2
A002
1.1
3.4
2.6
10.28
56.08
73
356.9
1
20P4
A003
1.9
4.2
2.9
4.573
42.21
62
288.2
2
20P7
A005
3.3
6.5
2.5
2.575
19.07
55
223.7
3
21P5
A008
6.2
11.1
2.6
1.233
13.40
45
169.4
4
22P2
A011
8.5
11.8
2.9
0.800
9.81
35
156.8
5
23P7
A017
14.1
19.0
3.3
0.385
6.34
32
122.9
7
25P5
A025
19.6
28.8
1.5
0.199
4.22
26
94.8
9
27P5
A033
26.6
43.9
1.3
0.111
2.65
30
72.7
10
40P2
B001
0.6
3.4
2.5
41.97
224.3
73
713.8
21
40P4
B002
1.0
4.0
2.7
19.08
168.8
63
576.4
22
40P7
B003
1.6
6.1
2.6
11.22
80.76
52
447.4
23
41P5
B005
3.1
11.0
2.5
5.044
53.25
45
338.8
24
42P2
–
4.2
11.7
3.0
3.244
40.03
35
313.6
25
43P7
B009
7.0
19.3
3.2
1.514
24.84
33
245.8
27
45P5
B015
9.8
28.8
1.5
0.797
16.87
26
189.5
29
47P5
—
13.3
43.9
1.3
0.443
10.59
30
145.4
30
Table A3-2. Parameters Related to Control Method
Parameter
n014
n015
Description
Frequency - Midpoint
Voltage - Midpoint
n016
n017
Frequency - Min.
Voltage - Min.
n097
n104
n108
n109
n111
n112
n113
n139
Overtorque Detection Selection
Torque Compensation Time
Motor Leakage Inductance
Torque Compensation Limit
Slip Compensation Gain
Slip Compensation Time
Slip Compensation Selection During Regeneration
Energy Saving Selection
A3-1
V/f Control Mode
(n002 = 0)
1.5
12.0 (230V)
24.0 (460V)
1.5
12.0 (230)
24.0 (460)
0.0
0.3
N/A
N/A
0.0
2.0
N/A
0.0
Open Loop Vector
(n002 = 1)
3.0
11.0 (230V)
22.0 (460V)
1.0
4.3 (230)
8.6 (460)
N/A
0.2
See table A3-1
150
1.0
0.2
0.0
N/A
A3-2
Appendix 4. PERIPHERAL DEVICES
The following peripheral devices may be required to be mounted between the AC main circuit power
supply and the Drive input terminals L1 (R), L2 (S) and L3 (T).
CAUTION
Never connect a general LC/RC noise filter to the drive output circuit.
Never connect a phase-advancing capacitor to the input/output sides or a
surge suppressor to the output side of the drive.
When a magnetic contactor is installed between the drive and the motor,
never turn it on or off during operation.
For more details on peripheral devices, contact your manufacturer.
Recommended Branch Circuit Short Circuit Protection Peripheral Devices
WARNING
All NEMA type 4X/12 models require branch circuit short circuit protection in
the form of fuses. Use the recommended fuses listed below. Failure to use
the listed fuses may result in damage to the drive and/or personal injury. All
other non-NEMA type 4 Drives can use either fuses or MCCBs for branch
circuit short circuit protection.
All models have UL evaluated motor overload protection built in. Motor
overload protection is also provided in accordance with the NEC and CEC.
Additional branch circuit overload protection is not required.
230V 3-Phase
Model
CIMR-V7*
MV
Capacity (kVA)
Rated output current (A)
Rated input current (A)
Max. Time Delay Fuse Rating (A) (1)
Max. Non-Time Delay Fuse Rating (A) (2)
Max. MCCB Rating (A)
20P1
A001
0.3
0.8
1.1
1.8
3
15
20P2
A002
0.6
1.6
1.8
3.2
5
15
20P4
A003
1.1
3.0
3.9
6.25
10
15
20P7
A005
1.9
5.0
6.4
10
20
15
21P5
A008
3.0
8.0
11.0
17.5
30
20
22P2
A011
4.2
11.0
15.1
20
45
30
23P7
A017
6.7
17.5
24.0
25
45
40
40P2
B001
0.9
1.2
1.6
2.8
5
15
40P4
B002
1.4
1.8
2.4
4
7
15
40P7
B003
2.6
3.4
4.7
8
12
15
41P5
B005
3.7
4.8
7.0
12
20
15
42P2
–
43P7
B009
7.0
9.2
12.0
20
35
20
45P5
B015
11.0
14.8
19.6
35
60
30
25P5
A025
9.5
25.0
33.0
45
70
50
460V 3-Phase
Model
CIMR-V7*
MV
Capacity (kVA)
Rated output current (A)
Rated input current (A)
Max. Time Delay Fuse Rating (A) (1)
Max. Non-Time Delay Fuse Rating (A) (2)
Max. MCCB Rating (A)
Notes:
(1)
Apply UL designated Class RK5 fuses.
(2)
Apply UL designated Class CC or T non-time delay fuses.
(3)
Model 47P5 rated 21A is only applicable to the NEMA type 4X/12 version.
Input fuse sizes are determined by NEC guidelines, and should not exceed the ratings shown in the table.
Fuse Ratings are based upon 250V fuses for 230V Drives, and 600V for 460V Drives
Fuse Manufacturer’s Designators:
Class CC: KTK, FNQ or equivalent
Class RK5: FRN, FRS or equivalent
Class T: JJS, JJN or equivalent
A4-1
47P5(3)
B018
14.0
18/21
23.8 / 27.8
45
70
40
27P5
A033
13.0
33.0
39.6
60
80
60
• Magnetic contactor
Mount a surge protector on the coil. When using a magnetic contactor to start and stop the drive, do
not exceed one start per hour.
• Ground fault interrupter
Select a ground fault interrupter not affected by high frequencies. To prevent malfunctions, the
current should be 200mA or more and the operating time 0.1 second or more.
• AC and DC reactor
Install a reactor to connect to a power supply transformer of large capacity (600 kVA or more) or to
improve the power factor on the power supply side.
• Noise filter
Use a noise filter exclusively for the drive if radio noise generated from the drive causes other
control devices to malfunction.
A4-2
Appendix 5. DRIVE DIMENSIONS
Fig. 1
2-d
0.06
(1.5)
H1
H2
W2
H3
H
H4
0.16
(4.0)
W1
0.33
(8.5)
D
W
V7 Enclosed wall mounted type (NEMA type 1)
Voltage
Class
Model
CIMRV7*
MV
Size
HP
W
H
D
(1)
W1
H1
H2
W2
H3
H4
d
Weight
Lbs.
(kg)
Heat Loss (W)
HeatFig.
sink Internal Total
20P1
A001
1/8
2.68
(68)
5.83
(148)
2.99
(76)
2.20 4.65
(56) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
1.55
(0.7)
3.7
9.3
13.0
1
20P2
A002
1/4
2.68
(68)
5.83
(148)
2.99
(76)
2.20 4.65
(56) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
1.55
(0.7)
7.7
10.3
18.0
1
20P4
A003
1/2
2.68
(68)
5.83 4.25 2.20 4.65
(148) (108) (56) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
2.20
(1.0)
15.8
12.3
28.1
1
20P7
A005
3/4 & 1
2.68
(68)
5.83 5.04 2.20 4.65
(148) (128) (56) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
2.65
(1.2)
28.4
16.7
45.1
1
230V
3-phase
Dimensions in inches (mm)
When drives include network communications option board, add 1.5" to drive depth.
A5-1
Fig. 2
4-d
H1
0.06
(1.5)
H
H3
H4
H2
0.16
(4.0)
W1
W2
D
0.33
(8.5)
W
V7 Enclosed wall mounted type (NEMA type 1)
Voltage
Class
230V
3-phase
460V
3-phase
(1)
Model
CIMRV7*
MV
Size
Dimensions in inches (mm)
HP
W
H
D
W1
H1
H2
W2
H3
H4
d
Weight
Lbs.
(kg)
Heat Loss (W)
HeatFig.
sink Internal Total
21P5
A008
2
4.25
(108)
5.83 5.16 3.78 4.65
(148) (131) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
3.53
(1.6)
53.7
19.1
72.8
2
22P2
A011
3
4.25
(108)
5.83 5.51 3.78 4.65
(148) (140) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
3.75
(1.7)
60.4
34.4
94.8
2
23P7
A017
5
5.51
(140)
5.83 5.63 5.04 4.65
(148) (143) (128) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
5.30
(2.4)
96.7
52.4 149.1
2
40P2
B001
1/2
4.25
(108)
5.83
(148)
3.78 4.65
(96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
2.65
(1.2)
9.4
13.7
23.1
2
40P4
B002
3/4
4.25
(108)
5.83 4.43 3.78 4.65
(148) (110) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
2.65
(1.2)
15.1
15.0
30.1
2
40P7
B003
1& 2
4.25
(108)
5.83 5.51 3.78 4.65
(148) (140) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
3.75
(1.7)
30.3
24.6
54.9
2
41P5
B005
3
4.25
(108)
5.83 6.14 3.78 4.65
(148) (156) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
3.75
(1.7)
45.8
29.9
75.7
2
42P2
–
3
4.25
(108)
5.83 6.14 3.78 4.65
(148) (156) (96) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
3.75
(1.7)
50.5
32.5
83.0
2
43P7
B009
5
5.51
(140)
5.83 5.63 5.04 4.65
(148) (143) (128) (118)
0.20
(5)
0.24
(6)
5.04 0.79
(128) (20)
M4
5.30
(2.4)
73.4
44.5 117.9
3.62
(92)
When drives include network communications option board, add 1.5" to drive depth.
A5-2
2
Fig. 3
4-d
0.06
(1.5)
H1
H
H2
0.09
(2.20)
W2
W1
W
D
0.33
(8.5)
V7 Enclosed wall mounted type (NEMA type 1)
Voltage
Class
Model
CIMRV7*
MV
Size
HP
H
D
W1
H1
H2
W2
H3
H4
d
Heat Loss (W)
HeatFig.
sink Internal Total
A025
7.5
7.09 10.24 6.70 6.46 9.61
(180) (260) (170) (164) (244)
0.31
(8)
0.31
(8)
–
–
M5
11.45
(5.2)
170.4
79.4 249.8
3
27P5
A033
10
7.09 10.24 6.70 6.46 9.61
(180) (260) (170) (164) (244)
0.31
(8)
0.31
(8)
–
–
M5
11.89
(5.4)
219.2
98.9 318.1
3
45P5
B015
10
7.09 10.24 6.70 6.46 9.61
(180) (260) (170) (164) (244)
0.31
(8)
0.31
(8)
–
–
M5
10.14
(4.6)
168.8
87.7 256.5
3
47P5
–
15 (3)
7.09 10.24 6.70 6.46 9.61
(180) (260) (170) (164) (244)
0.31
(8)
0.31
(8)
–
–
M5
10.58
(4.8)
209.6
99.3 308.9
3
460V
3-phase
W
Weight
Lbs.
(kg)
25P5
230V
3-phase
Dimensions in inches (mm)
(1)
When drives include network communications option board, add 1.5" to drive depth.
(2)
230 and 460V drives represented in Figure 3 can be used as “IP00” type enclosures
if the top and bottom covers are removed.
(3)
Horsepower rating of 15 only available as V74X drive.
A5-3
Fig. 4
4-d
H1
H
H2
W1
W2
W
D
V74X Enclosed wall mounted type (NEMA 4)
Voltage
Class
Model
CIMRV7CU
Size
HP
W
H
D
W1
H1
H2
W2
d
Weight
Lbs.
(kg)
20P24
0.25
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
7.8
(3.52)
4
20P44
0.5
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
8.0
(3.62)
4
20P74
1
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
8.2
(3.72)
4
21P54
2
6.69
(170)
10.0
(254)
7.48
(190)
6.22
(158)
9.41
(239)
0.24
(6)
0.24
(6)
0.20
(5)
13.0
(5.90)
4
22P24
3
6.69
(170)
10.0
(254)
7.48
(190)
6.22
(158)
9.41
(239)
0.24
(6)
0.24
(6)
0.20
(5)
13.3
(6.00)
4
23P74
5
6.69
(170)
10.0
(254)
7.48
(190)
6.22
(158)
9.41
(239)
0.24
(6)
0.24
(6)
0.20
(5)
13.7
(6.20)
4
25P54
7.5
11.41
(290)
15.98
(406)
11.34
(288)
10.63
(270)
14.17
(360)
0.91
(23)
0.39
(10)
0.28
(7)
41.5
(18.6)
4
27P54
10
11.41
(290)
15.98
(406)
11.34
(288)
10.63
(270)
14.17
(360)
0.91
(23)
0.39
(10)
0.28
(7)
41.5
(18.8)
4
40P24
1/2
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
8.4
(3.82)
4
40P44
3/4
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
8.4
(3.82)
4
40P74
1&2
6.10
(155)
7.56
(192)
6.50
(165)
5.55
(141)
7.01
(178)
0.28
(7)
0.28
(7)
0.20
(5)
8.7
(3.92)
4
41P54
3
6.69
(170)
10.0
(254)
7.48
(190)
6.22
(158)
9.41
(239)
0.24
(6)
0.24
(6)
0.20
(5)
13.3
(6.00)
4
42P24
3
6.69
(170)
10.0
(254)
7.48
(190)
6.22
(158)
9.41
(239)
0.24
(6)
0.24
(6)
0.20
(5)
13.3
(6.00)
4
43P74
5
7.5 & 10
10.0
(254)
15.74
(400)
7.48
(190)
11.42
(290)
6.22
(158)
10.63
(270)
9.41
(239)
14.17
(360)
0.24
(6)
0.79
(20)
0.24
(6)
0.39
(10)
0.20
(5)
0.28
(7)
13.7
(6.20)
41.5
(18.8)
4
45P54
6.69
(170)
11.41
(290)
47P54
15(1)
11.41
(290)
15.74
(400)
11.42
(290)
10.63
(270)
14.17
(360)
0.79
(20)
0.39
(10)
0.28
(7)
41.5
(18.8)
4
230V
3-Phase
460V
3-Phase
Dimensions in inches (mm)
When drives include network communications option board, add 2.0" to drive depth.
(1)
Applicable to the V74X Model only.
A5-4
Fig.
4
Appendix 6. DYNAMIC BRAKING OPTION
GENERAL. Dynamic braking (DB) enables the motor to be brought to a smooth and rapid stop.
This is achieved by dissipating the regenerative energy of the AC motor across the resistive components of the Dynamic Braking option. For further details on dynamic braking, see the option instruction sheet shipped with the dynamic braking components.
The Drive has an integral braking transistor. However, to make use of the Dynamic Braking function
requires addition of either a Braking Resistor (for 3% duty cycle) or Braking Resistor Unit (for 10%
duty cycle). See table below. In either case, interface to external control circuitry is necessary to
ensure that dynamic brake resistor overheating is communicated to the drive as a fault condition.
Table A6-1. Drive DB Components
Model
CIMRV7*
MV
20P1
A001
20P2
A002
20P4
A003
20P7
A005
21P5
A008
22P2
A011
23P7
A017
25P5
A025
27P5
A033
40P2
B001
40P4
B002
40P7
B003
41P5
B005
42P2
–
43P7
B009
45P5
B015
47P5
—
(1)
Size
HP
1/8
1/4
1/2
3/4&1
2
3
5
7.5
10
1/2
3/4
1&2
3
3
5
7.5&10
15(1)
DB Components
Braking Resistor - 3% Duty
Part No.
Qty. Reqd.
50185531
1
50185531
1
50185430
1
50185430
1
50185431
1
50185432
1
50185433
1
N/A
—
N/A
—
50185530
1
50185530
1
50185530
1
50185531
1
50185531
1
50185531
2
N/A
—
N/A
—
Applicable to the V74X model only
A6-1
Braking Resistor - 10% Duty
Part No.
Qty Reqd.
—
—
—
—
05P00041-0825
1
05P00041-0825
1
05P00041-0827
1
05P00041-0827
1
05P00041-0828
1
05P00041-0829
1
05P00041-0830
1
05P00041-0835
1
05P00041-0835
1
05P00041-0835
1
05P00041-0837
1
05P00041-0837
1
05P00041-0838
1
05P00041-0840
1
05P00041-0841
1
Minimum
Connect
Resistance (SL)
300
300
200
120
60
60
32
9.6
9.6
750
750
510
240
240
100
32
32
DYNAMIC BRAKING OPTION INSTALLATION. This option must be installed by a TECHNICALLY
QUALIFIED INDIVIDUAL who is familiar with this type of equipment and the hazards involved.
WARNING
HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR DEATH.
LOCK ALL POWER SOURCES FEEDING THE DRIVE IN “OFF” POSITION.
CAUTION
Failure to follow these installation steps may cause equipment damage or
personnel injury.
Preliminary Procedures
1. Disconnect all electrical power to the drive.
2. Open the Drive’s terminal covers.
3. Verify that voltage has been disconnected by using a voltmeter to check for voltage at the
incoming power terminals, L1 (R), L2 (S) and L3 (T).
Braking Resistor (3% Duty Cycle) Installation
Note: The 3% duty cycle Braking Resistor is supplied with 6-inch leads.
1. Mount the Braking Resistor, along with an overload or thermostat, in a suitable metal enclosure.
2. At the Drive. Connect the leads from the Braking Resistor to drive terminals B1 and B2, and
make connections to external control circuit, as shown in Figure A6-1.
3. Close the Drive’s terminal covers.
4. Proceed to “Adjustments” on page A6-4.
A6-2
OVERLOAD
NOTE 3
CB
1M
L3
1M
L2
L1(R) L2(S) L3(T)
1M
L1
B1 B2
V7N
THERMOSTAT
NOTE
3
OR
OVERLOAD
CONTROL
TERMINAL BLOCK
S3
NOTE 2
SC
T1(U) T2(V) T3(W)
SEPARATE CUSTOMER
SUPPLIED ENCLOSURE
AND THERMISTOR
OR OVERLOAD
BRAKING
RESISTOR
(3% DUTY
CYCLE)
NOTE 1
T1
T2
T3
THRX
PART OF CUSTOMER
SUPPLIED EXTERNAL
CIRCUIT
120 VAC
THRX
NOTES:
(1) Wire in series with any other external fault
N.O. contacts connected to the Drive.
RC
THRX
POWER
OFF
POWER
ON
1M
1M
(2) Factory default is terminal S3 programmed
for external fault N.O. contact input (2-wire
control). If S3 has been reprogrammed to
another function, one of the other multifunction terminals must be programmed
for external fault N.O. contact input.
RC
THRX
FAULT
CONTACT
For 3-wire control, connect to one of the
other multi-function input terminals and
program that terminal for external fault
N.O. contact input.
(3) Either an overload can be used in series with
the Braking resistor or a thermostat can be
configured as shown.
Figure A6-1. Typical Wiring of Braking Resistor
(for 3% Duty Cycle) to Drive
A6-3
Braking Resistor (10% Duty Cycle) Installation
IMPORTANT
Since the Braking Resistor Unit generates heat during the dynamic
braking operation, install it in a location away from other equipment
which emits heat.
1. Mount the Braking Resistor Unit on a vertical surface, maintaining minimum 1.18 inch (30
mm) clearance on each side and 5.91 inch (150 mm) clearance top and bottom.
2. Open the Braking Resistor Unit terminal box to access its terminal block. Connect the
Braking Resistor Unit to the drive and external control circuit according to the following table
and Figure A6-2.
Terminals
Lead Size (AWG)
Lead Type
Terminal Screw
B, P, B1, B2
1, 2, S3, SC*
12 - 10
18 - 14 *
600V ethylene propylene rubber insulated,
or equivalent
M4 (resistor end)
* Power leads for the Braking Resistor Unit generate high levels of electrical
noise; therefore, signal leads must be grouped separately.
3. Close and secure the cover of the Braking Resistor Unit terminal box. Close the Drive’s
terminal covers.
4. Adjustments. Program constant n092 to “ 1 ”; this disables stall prevention during
deceleration.
A6-4
CB
1M
L3
P
1M
L2
L1(R) L2(S) L3(T)
1M
L1
B1 B2
2
V7N
1
CONTROL
TERMINAL BLOCK
S3
NOTE 2
THG
B
BRAKING
RESISTOR
UNIT
(10% DUTY
CYCLE)
SC
T1(U) T2(V) T3(W)
NOTE 1
T1
T2
T3
THRX
PART OF CUSTOMER
SUPPLIED EXTERNAL
CIRCUIT
120 VAC
THRX
NOTES:
(1) Wire in series with any other external fault
N.O. contacts connected to the Drive.
RC
THRX
POWER
OFF
POWER
ON
1M
1M
(2) Factory default is terminal S3 programmed
for external fault N.O. contact input (2-wire
control). If S3 has been reprogrammed to
another function, one of the other multi-function
terminals must be programmed for external
fault N.O. contact input.
RC
THRX
FAULT
CONTACT
For 3-wire control, connect to one of the
other multi-function input terminals and
program that terminal for external fault
N.O. contact input.
Figure A6-2. Typical Wiring of Braking Resistor Unit
(for 10% Duty Cycle) to Drive
A6-5
A6-6
Appendix 7. NAMEPLATE INFORMATION
PLASTIC
CASE
STATUS
INDICATOR
LAMPS
NAMEPLATE
WARNING
DISPLAY
V7 [NEMA type 1]
NAMEPLATE
(INTERIOR)
WARNING
DISPLAY
FACE
COVER
NAMEPLATE
(EXTERIOR)
V74X [NEMA type 4X/12]
A7-1
MODEL NO.
REFERENCE
INPUT SPEC
OUTPUT SPEC
LOT NO.
SERIAL NO.
INVERTER SPEC
MODEL: CIMR-V7AU23P7
SPEC: 23P71
MVA017
REF:
INPUT: 3PH 200-230VAC 50/60Hz 24A
OUTPUT: 3PH 0-230VAC MAX. 0-400Hz 17.5A
LOT NO.:
MASS: 2.4kg
SER NO.: N8W0593-8-043/V9905
MASS
SOFTWARE NO.
INSTALLATION CATEGORY
PRG: 8021
IP20
FILE NO.: E131457
INSTALLATION CATEGORY: II
V7 [NEMA type 1]
MODEL NO.
INPUT SPEC
OUTPUT SPEC
LOT NO.
SERIAL NO.
DRIVE SPEC
MASS
SOFTWARE NO.
ENCLOSED TYPE
MODEL: CIMR-V7CU23P7
SPEC: 23P74
AC3PH 200-230V 50/60Hz 24A
INPUT:
OUTPUT: AC3PH 0-230V 0-400Hz 17.5A 7.0kVA
MASS: 6.2kg
O/N:
S/N:
PRG:
ENCL: TYPE 4/12 “INDOOR USE ONLY”
FILE: E131457
IP66
MODEL NO.
DRIVE SPEC
SERIAL NO.
200V
MODEL: CIMR-V7CU20P7
SPEC: 20P74
10A000279-4
V74X [NEMA type 4X/12]
Model Number Structure
CIMR-V7AM23P7
No.
DRIVE
V7 SERIES
No. Type
A With digital operator
B
Without digital operator
C
With digital operator
R
Finless
Applicable max. motor output (HP)
0P1
230V
1/8
460V
–
0P2
1/4
1/2
0P4
1/2
3/4
0P7
3/4 & 1
1&2
1P5
2
3
2P2
3
3
3P7
5
5
5P5
7.5
7.5 & 10
7P5
10
15(1)
No. Voltage Class
B Single-phase
Note: Contact your YASKAWA representative
for finless type drives.
230VAC
2
Three-phase
230VAC
4
Three-phase
460VAC
No. Specifications
U UL Specification (U.S.)
or M Specification)
(1)
A7-2
Applies to NEMA type 4x/12 model only
Ref Model Number Structure (applicable to V7/NEMA type 1 only)
A001
A
Three-phase 200VAC
B
Three-phase 400VAC
No.
Current rating
001
002
003
005
008
011
017
025
033
001
002
003
005
009
015
021
0.8 A
1.6 A
3.0 A
5.0 A
8.0 A
11.0 A
17.5 A
25.0 A
33.0 A
1.2 A
1.8 A
3.4 A
4.8 A
9.2 A
14.8 A
21.0 A
Drive Spec Structure
20P10
B
Single-phase 200VAC
2
4
Three-phase 200VAC
No. Applicable maximum motor output
0P1
0.13 HP
Three-phase 400VAC
0P2
0.25 HP
0P4
0.5 HP
0P7
1 HP
1P5
2 HP
2P2
3 HP
3P7
5 HP
5P5
7.5 & 10 HP
7P5
15 HP(1)
No. Protective structure
0
Open chassis
(IP20, IP00)
1
(NEMA 1)
4
Water and dust tight
(NEMA 4/IP66)
7
Open chassis (IP20)
Top-closed type
Note: Model Number and Drive Spec Number are required to fully define a drive.
(1)
Applies to NEMA type 4x/12 model only
A7-3
Enclosed wall-mounted
A7-4
Appendix 8. REMOVE/INSTALL DRIVE FACE PLATES
REMOVING AND MOUNTING DIGITAL OPERATOR COVERS
NOTE: Mount the Drive after removing the
front cover, digital operator and terminal
cover.
1
2
• Removing front cover
Use a screwdriver to loosen the screw on
the front cover surface to direction 1 to
remove it. Then press the right and left
sides to direction 2 and lift the front cover
to direction 3.
3
2
• Mounting front cover
Mount the front cover in the reverse order
of the above procedure for removal.
• Removing terminal cover when “W”
(Width) dimensions are 4.25" (108mm),
5.51" (140mm), or 6.69" (170mm)
After removing the front cover, press the
right and left sides to direction 1 and lift
the terminal cover to direction 2.
• Removing terminal cover when “W”
(Width) dimensions are 7.09" (180mm)
Use a screwdriver to loosen the screw on
the terminal cover surface to direction 1
to remove it. Then press the right and left
sides to direction 2 and lift the terminal
cover to direction 3.
• Mounting terminal cover
Mount the terminal cover in the descending order of the above procedure for
removal.
A8-1
1
2
1
1
2
3
2
• Removing digital operator
After removing the front cover, lift the
upper and lower sides (section A) of the
right side of the digital operator to direction 1.
1
A
A
• Mounting digital operator
Mount the digital operator in the reverse
order of the above procedure for removal.
• Removing bottom cover when “W”
(Width) dimensions are 4.25" (108mm),
5.51" (140mm), or 6.69" (170mm)
After removing the front cover and the
terminal cover, tilt the bottom cover to
direction 1 with section A as a supporting
point.
A
A
• Removing terminal cover when “W”
(Width) dimensions are 7.09" (180mm)
After removing the terminal cover use a
screwdriver to loosen the fastening screw
to direction 1 to remove it.
• Mounting bottom cover
Mount the bottom cover in the reverse
order of the above procedure for removal.
A8-2
1
Removing the front cover and the bottom cover of V74X [NEMA type 4X/12]
Models 20P1-22P7 & 40P2-43P7
IMPORTANT
Damage to the drive can occur if the front cover is removed too quickly.
Front Cover:
Remove the four mounting bolts and slowly take off the cover. Disconnect the cable between the face
cover and the control board located in the lower portion of the Drive. For mounting, reverse the direction.
Bottom Cover:
Remove the four mounting bolts when installing cable glands, etc. Install wiring after inserting cables
through the cable glands and securing them to the bottom cover. See section 1-4 on recommended
cable gland sizes. Conduit plate gasket may be attached to the Drive and may not be removable in
some cases.
To remove the front cover of V74X [NEMA type 4X/12], models 25P5, 27P5, 45P5 and 47P5:
Remove the six mounting bolts from the front of the enclosure, then carefully remove front cover.
A8-3
A8-4
INDEX
Time setting unit ................................... 5-2
Decrease ( ) key .................................. 4-1
Diagnostics — see
Troubleshooting
Digital operator ......................................... 4-1
Dimensions ................................... A5-1, A5-2
Display Selection ......................................5-52
DSPL key .................................................. 4-1
Dynamic braking option .......................... A6-1
-AAcceleration :
Accel time 1 ........................................... 5-2
Accel time 2 ........................................... 5-2
Hold ..................................................... 5-27
S-curve .................................................. 5-3
Time setting unit .................................... 5-2
Analog monitor outputs,
multi-function ....................................... 5-20
Analog inputs,
multi-function selection ........................ 5-55
Auto restart ............................................... 5-4
-EEMC Directive, European,
Conformance to ............................... 1-9
Enclosure ............................................... A2-2
Energy Saving ..........................................5-53
Environment .................................... 1-1, A2-2
External base block ................................ 5-24
-BBraking :
DC injection ........................................... 5-7
Dynamic .............................................. A6-1
-F-CF/R LED .................................................... 4-2
Fault displays ............................................ 6-1
Fault history .............................................. 6-8
Faults :
Restart attempts ................................... 5-4
FOUT LED ................................................ 4-2
FREF LED ................................................ 4-2
Frequency :
Detection ............................................ 5-31
Max. output ........................................ A2-1
Output (FOUT) ..................................... 4-2
Output (monitor) ................................... 4-4
Frequency reference :
Bias (analog) ........................................ 5-8
Gain (analog) ....................................... 5-8
Jog ...................................................... 5-13
Limits .................................................... 5-9
Loss detection ..................................... 5-57
Retention (Up/Down) ................................ 5-9
Selection ................................................. 5-10
V/f parameters ........................................ 5-41
Fusing, Recommended ............................A4-2
Carrier frequency ...................................... 5-5
Conformance to European
EMC Directive .................................. 1-8
Contactors –– see
Peripheral Devices
Control circuit :
Terminals .............................................. 1-6
Wiring ................................................... 1-5
Copy function ............................................5-46
Critical frequency
rejection .................................................. 5-6
Current :
Limit — see Stall Prevention
Motor .............................................. 2-3, 2-7
Output (IOUT)........................................ 4-2
Output (monitor) .....................................4-4
-DDATA/ENTER key .....................................
DC injection :
Time at start .........................................
Time at stop ..........................................
Deadband, prohibited
frequency .........................................
Deceleration :
Decel time 1 .........................................
Decel time 2 .........................................
S-curve .................................................
4-1
5-7
5-7
-G-
5-6
Gain :
Analog monitor ................................... 5-20
Frequency reference (analog) .............. 5-8
Torque compensation ......................... 5-39
Grounding ................................................. 1-5
5-2
5-2
5-3
I-1
Mounting :
Clearances ........................................... 1-1
Dimensions .............................. A5-1, A5-2
European EMC
conformance .................................... 1-8
Location ...................................... 1-1, A2-2
Multi-function analog
input selection ................................. 5-55
Multi-function analog
monitor output ....................... 5-20, 5-21
Multi-function input
terminals .............................. 5-22 - 5-27
Multi-function output
terminals ........................................ 5-28
Multi-step speeds ................................... 5-10
-HHeat loss (watts) ........................... A5-1, A5-2
Hold :
Accel/decel ................................ 5-23, 5-27
Frequency ref. (retention) ..................... 5-9
-IIncrease ( ) key ........................................ 4-1
Initialize parameters ................................ 5-33
Inputs, multi-function ............................... 5-21
Inspection (receiving) ............................... 1-1
Installation:
Electrical ............................................... 1-4
Physical ................................................ 1-1
IOUT LED ................................................. 4-2
-NNameplate, motor ...................... 2-2, 2-3, 2-7
-J-
-O-
Jog reference .......................................... 5-13
Open loop vector startup .......................... 2-2
Operation at load ...................................... 3-1
Operation mode ...................................... 5-14
Operator display ....................................... 4-1
Options — see Peripheral
Devices or Dynamic Braking
Outputs :
Analog ................................................ 5-20
Contact ............................................... 5-28
Multi-function ...................................... 5-28
Open collector .................................... 5-28
Overtorque detection .............................. 5-31
-KKeypad — see Digital Operator
-LLEDs :
Function ................................................ 4-2
Status Indicator .................................... 4-3
Local/Remote reference and
sequence selection ........................ 5-14
LO/RE LED ............................................... 4-2
-P-
-M-
Parameters :
Capacity and control
method related .............................. A3-1
Listing of ............................................ A1-1
Reset (initialize) .................................. 5-33
Peripheral devices :
AC and DC reactor ............................ A4-1
Ground fault interrupter ...................... A4-1
Magnetic contactor ............................ A4-1
Molded-case circuit
breaker (MCCB) ............................... A4-1
Noise filter ................................... 1-8, A4-1
PID Control ............................................. 5-42
Potentiometer ............................................ 4-1
Power loss ride-through .......................... 5-20
Power supply .......................................... A2-1
Pre-power checks ..................................... 2-1
Main circuit :
Terminals .............................................. 1-4
Wiring ................................................... 1-4
Mechanical resonance —
see Critical Frequency Rejection
MNTR LED ............................................... 4-2
MODBUS control .................................... 5-16
Model Number, GPD 315 ....................... A2-1
Momentary power loss ride-through ....... 5-20
Monitor displays ........................................ 4-3
Motor :
No-load current ...................... 2-4, 2-5, 5-34
Protection ........................................... 5-38
Rated current ....................... 2-4, 2-5, 5-34
Rated slip ............................................. 2-3
Switching — see Speed Search
Wiring ................................................... 1-4
I-2
Preset speeds — see
Multi-step speeds
PRGM LED ............................................... 4-2
Prohibited frequency
deadband ................................................ 5-6
Protection :
Overcurrent ........................................ 5-35
Overheat (drive) ................................. A2-1
Overtorque ......................................... 5-31
Overvoltage (decel) ............................ 5-35
Thermal overload (mtr) ....................... 5-38
Undervoltage ...................................... A2-2
Protective functions,
miscellaneous ................................ 5-20
-T Temperature :
Ambient .............................................. A2-2
Storage .............................................. A2-2
Terminals :
Functions ...................................... 1-4, 1-6
Screw sizes .......................................... 1-3
Thermal overload protection ..................... 5-38
Torque boost (open loop
vector) ............................................ 5-39
Torque compensation
gain (V/F control) ................................ 5-39
Torque detection ..................................... 5-31
Troubleshooting ........................................ 6-1
-R-URated current, motor ........................... 2-3, 2-7, 5-38
Ratings ................................................ i, A2-1
Receiving .................................................. 1-1
Remote reference — see
Local/Remote
Reset codes ............................................ 5-33
Reverse prohibit ............................ 1-10, 1-12
Ride-through ........................................... 5-20
RUN key .................................................... 4-1
Up/down function .................................... 5-26
Undertorque detection ............................. 5-58
-V V/f pattern ............................................... 5-40
V/f startup procedure ................................ 2-6
Voltage :
DC bus (monitor) .................................. 4-4
DC bus (stall prev.) ............................. 5-35
Max. output ........................................ A2-1
Output (monitor) ................................... 4-4
V/f parameters .................................... 5-41
-SS-curve ..................................................... 5-3
Shock resistance –– see
S-curve
Slip compensation .................................. 5-34
Soft start — see S-curve
Specifications ......................................... A2-1
Speed :
Coincidence ........................................ 5-30
Search ................................................ 5-23
Stall prevention :
Accel ................................................... 5-35
Decel .................................................. 5-35
During running .................................... 5-36
Start-up:
Open loop vector .................................. 2-2
V/f control ............................................. 2-6
STOP/RESET key ........................... 4-1, 5-14
Stopping method selection ..................... 5-37
Switches, internal :
SW1 .................................................... 5-22
SW2 .......................................... 5-10, 5-16
Switching frequency — see
Carrier frequency
-W Weight ........................................... A5-1, A5-2
Wiring :
2-Wire control ....................................... 1-4
3-Wire control ....................................... 1-4
Auxiliary input and output
power option devices ....................... 1-7
Conduit ..................................................1-7
Control circuit ....................................... 1-5
Diagrams ................................... 1-11, 1-13
Distances ..................... 1-4, 1-5, 1-8, A2-2
Main circuit ........................................... 1-4
I-3
I-4
Drives Technical Support in USA and Canada
Technical Support for Inverters and Drives is available by phone as follows:
Normal:
Monday through Friday during the hours of 8 a.m. to 5:00 p.m. C.S.T.
Emergency:
After normal hours, 7 days a week including weekends and holidays
To contact Drives Technical Support, please call 1-800-YASKAWA (927-5292).
From the menu, dial 2 for Inverter and Drive Products, then 5 for Technical Support.
Drives Technical Support can also be reached by e-mail at [email protected].
Support information, such as technical manuals, FAQs, instruction sheets and software downloads are available at our website,
www.drives.com.
When calling for technical support, please have the following materials available:
The appropriate Technical Manual in hand because the support associate may refer to this
Complete nameplate information from the drive and the motor.
(Confirm that Drive Nameplate Output amps is greater than Motor Nameplate amps)
list with your parameter settings
A sketch of the electrical powertrain, from AC line to motor, including filters and disconnects
Field Service, Start Up Assistance, Factory Repair, Replacement Parts, and Other Support
Contact Drives Technical Support for help with any of these needs.
Technical Training
Training is conducted at Yaskawa training centers, at customer sites, and via the internet.
For information, visit www.drives.com or call 1-800-YASKAWA (927-5292).
From the phone menu, dial 2 for Inverter and Drive Products, then 4 for Product Training.
Support in Other Countries
Yaskawa is a multi-national company with offices and service representation around the world.
To obtain support, always contact the local distributor first for guidance and assistance.
Contact the closest Yaskawa office listed for further assistance.
V7 and V74X Drives
YASKAWA ELECTRIC AMERICA, INC.
Drives Division
16555 W. Ryerson Rd., New Berlin, WI 53151, U.S.A.
Phone: (800) YASKAWA (800-927-5292) Fax: (262) 782-3418
Internet: http://www.drives.com
YASKAWA ELECTRIC AMERICA, INC.
Chicago-Corporate Headquarters
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone: (800) YASKAWA (800-927-5292) Fax: (847) 887-7310
Internet: http://www.yaskawa.com
MOTOMAN INC.
805 Liberty Lane, West Carrollton, OH 45449, U.S.A.
Phone: (937) 847-6200 Fax: (937) 847-6277
Internet: http://www.motoman.com
YASKAWA ELECTRIC CORPORATION
New Pier Takeshiba South Tower, 1-16-1, Kaigan, Minatoku, Tokyo, 105-0022, Japan
Phone: 81-3-5402-4511 Fax: 81-3-5402-4580
Internet: http://www.yaskawa.co.jp
YASKAWA ELETRICO DO BRASIL COMERCIO LTDA.
Avenida Fagundes Filho, 620 Bairro Saude Sao Paolo-SP, Brasil CEP: 04304-000
Phone: 55-11-5071-2552 Fax: 55-11-5581-8795
Internet: http://www.yaskawa.com.br
YASKAWA ELECTRIC EUROPE GmbH
Am Kronberger Hang 2, 65824 Schwalbach, Germany
Phone: 49-6196-569-300 Fax: 49-6196-888-301
MOTOMAN ROBOTICS AB
Box 504 S38525, Torsas, Sweden
Phone: 46-486-48800 Fax: 46-486-41410
MOTOMAN ROBOTEC GmbH
Kammerfeldstrabe 1, 85391 Allershausen, Germany
Phone: 49-8166-900 Fax: 49-8166-9039
YASKAWA ELECTRIC UK LTD.
1 Hunt Hill Orchardton Woods Cumbernauld, G68 9LF, Scotland, United Kingdom
Phone: 44-12-3673-5000 Fax: 44-12-3645-8182
YASKAWA ELECTRIC KOREA CORPORATION
Paik Nam Bldg. 901 188-3, 1-Ga Euljiro, Joong-Gu, Seoul, Korea
Phone: 82-2-776-7844 Fax: 82-2-753-2639
YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.
Head Office: 151 Lorong Chuan, #04-01, New Tech Park Singapore 556741, SINGAPORE
Phone: 65-282-3003 Fax: 65-289-3003
TAIPEI OFFICE (AND YATEC ENGINEERING CORPORATION)
10F 146 Sung Chiang Road, Taipei, Taiwan
Phone: 886-2-2563-0010 Fax: 886-2-2567-4677
YASKAWA JASON (HK) COMPANY LIMITED
Rm. 2909-10, Hong Kong Plaza, 186-191 Connaught Road West, Hong Kong
Phone: 852-2803-2385 Fax: 852-2547-5773
BEIJING OFFICE
Room No. 301 Office Building of Beijing International Club,
21 Jianguomanwai Avenue, Beijing 100020, China
Phone: 86-10-6532-1850 Fax: 86-10-6532-1851
SHANGHAI OFFICE
27 Hui He Road Shanghai 200437 China
Phone: 86-21-6553-6600 Fax: 86-21-6531-4242
SHANGHAI YASKAWA-TONJI M & E CO., LTD.
27 Hui He Road Shanghai 200437 China
Phone: 86-21-6533-2828 Fax: 86-21-6553-6677
BEIJING YASKAWA BEIKE AUTOMATION ENGINEERING CO., LTD.
30 Xue Yuan Road, Haidian, Beijing 100083 China
Phone: 86-10-6232-9943 Fax: 86-10-6234-5002
SHOUGANG MOTOMAN ROBOT CO., LTD.
7, Yongchang-North Street, Beijing Economic & Technological Development Area,
Beijing 100076 China
Phone: 86-10-6788-0551 Fax: 86-10-6788-2878
YEA, TAICHUNG OFFICE IN TAIWAIN
B1, 6F, No.51, Section 2, Kung-Yi Road, Taichung City, Taiwan, R.O.C.
Phone: 886-4-2320-2227 Fax:886-4-2320-2239
Document Number: TM.V7.01 4/1/06
Rev: 06-04
Data Subject to change without notice. Yaskawa Electric America, Inc.
">