30 TON LOG SPLITTER
TOWL30
198374
Operator’s Manual
Read the Operator’s Manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious follow without exception. Your life and the lives
of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit. For an Operator’s Manual and Decal
Kit in French or Spanish Language, please see your dealer
GENERAL WARNINGS
READ and UNDERSTAND this manual completely before using 30 Ton Log Splitter.
Operator must read and understand all safety and warning information, operating instructions, maintenance,
and storage instructions before operating this equipment. Failure to properly operate and maintain the log
splitter could result in serious injury to the operator or bystanders.
OPERATION WARNINGS
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not at any time carry passengers, sit, or stand on the log splitter.
Do not allow children to play on, stand upon or climb on the log splitter.
Always inspect the log splitter before using to assure it is in good working condition.
Replace or repair damaged or worn parts immediately.
Always check and tighten hardware and assembled parts before operation.
Do not exceed equipment maximum load capacity of 30 tons.
Avoid large holes and ditches when towing the equipment.
Always operate the log splitter on clear and level ground.
Do not operate the log splitter at night, only during daylight hours.
Always tow at reduce speed in rough terrain, along creeks, ditches and on hillsides.
To avoid personal injury and/or equipment damage DO NOT EXCEED 45 MPH.
Always refer to the vehicle owner’s manual for proper towing.
Always secure and lock the log splitter to the vehicle hitch before towing.
CRUSH AND CUT HAZARDS
Always keep hands and feet clear from moving parts while operating the equipment.
Always clear and keep work area clean and free of debris when operating.
Always wear safety gear, eye protection, gloves and work boots when operating the log splitter.
WARNING
The warnings, cautions, and instructions outlined in this instruction manual cannot cover all possible
conditions or situations that may occur. It must be understood by the operator that common sense
and caution are factors which cannot be built into this product and must be supplied by the operator.
PROP 65 WARNING
This product can expose you to chemicals including lead and lead compounds which are known to
the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov.
ASSEMBLY IS REQUIRED
This product requires assembly before use. See “Assembly” section for instructions. Because of the weight
and/or size of the log splitter, it is recommended that another adult be present to assist with theassembly.
INSPECT ALL COMPONENTS closely upon receipt to make sure no components are missing or damaged.
2
HAZARD SIGNAL WORD DEFINITIONS
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
WARNING
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation
which,
if not avoided, may result in property damage.
ABOUT YOUR 30 TON LOG SPLITTER
This hydraulic log splitter has a heavy-duty steel construction and 30 tons of ram force. When there's work to be
done, you need outdoor power equipment you can rely on, this log splitter will get the job done fast. It is
designed to work in both the horizontal and vertical position. It is easy to tow, easy to use and maintain. Never
exceed the rated capacity of 30 tons when operating the log splitter.
Technical specifications on the log splitter are provided in the “Specifications” section of this manual.
3
CONTROLS AND FEATURES IDENTIFICATION
Read this owner’s manual before operating the equipment. Familiarize yourself with the location
andfunction of the controls and features. Save this manual for future reference.
1) 2” Coupler – Attaches the log splitter to the 2” ball.
2) Hydraulic Cylinder – 4.5” bore and 24.5” stroke, rated to 3625 psi.
3) Control Valve – Controls the forward and backward movement of splitting wedge.
4) 8” Wedge - Feature’s wedge wings and tapered ends making splitting easier.
5) External Filter – Filters the hydraulic oil.
6) Beam – 7.9” wide
7) Engine - Air cooled engine powers the hydraulic pump.
8) Tires - Maximum rated towing speed is 45 MPH.
9) Gear Pump - Pumps the hydraulic oil through the system.
10) Support Leg - Supports the log splitter while operating.
11) Safety Chains - Safety feature to prevent loss of log splitter while towing.
4
WARNING
Read and follow all instructions for assembly and operation. Failure to properly assemble this
equipment could result in serious injury to the user or bystanders, or cause equipment damage.
Engine Shipped Without Oil.
Before starting engine, fill with SAE 10W-30 motor oil.
See engine manual for engine oil capacity.
Hydraulic Reservoir is Shipped Without Oil.
When adding oil verify the oil level reads 1 from the top of hydraulic
reservoir if marking is not shown fill to the neck.
Inspect all Log Splitter Components.
If you have damaged components:
Contact the freight company
thatdelivered the log splitter and file a claim.
30 TON LOG SPLITTER ASSEMBLY
Set the shipping crate on a solid flat surface and carefully remove the lid. Use two people and take all
parts out of the shipping crate and inspect the components to ensure there are no missing pieces
before starting to assemble the log splitter follow steps 1 through 8.
TOOLS REQUIRED
• Rubber or Wooden Hammer
• 13mm, 16mm, 17mm, 18mm, 19mm, 24mm, 27mm Wrenches
• Large Adjustable Wrench
• Phillips Screwdriver
• Pliers
ASSEMBLY INSTRUCTIONS
STEP 1: WHEEL ASSEMBLY
1. Attach the wheel (#35) to the oil tank axle (#44) using a flat washer Ø20 (#54) and tighten the
wheel with the hex slotted nut M20x1.5 (#37). Lock the hex slotted nut M20x1.5 (#37) in place
using the cotter pin Ø4x36 (#73). Install the axle cap (#41) on the end using rubber hammer.
NOTE: Use a black plastic bushing to fix the axle cap (#41) like below
picture. Please cover the black bushing onto the axle cap and use
rubber/wooden hammer knocking the end of the plastic bushing and
make the axle cap fixed on wheel.
5
WARNING: After the slotted nut is
tightened, turn back 1/4 circle to
make sure the wheel can rotate
smoothly and freely. Failure to turn
the slotted nut back will cause the
wheel not to operate correctly
STEP 2: ATTACH TOW BAR TO THE WHEEL ASSEMBLY
1. Attach the tow bar (#62) to the oil tank using hex bolt M12x100 (#24), flat washer Ø12 (#65)
and lock nut M12 (#13).
STEP 3: ATTACH THE BEAM ASSEMBLY
1. Connect the Beam (#17) and Oil Tank using Hitch Pin (#18), then lock the Hitch Pin (#18)
using R Pin (#21).
6
STEP 4: ATTACH ENGINE TO MOUNTING PLATE
1. Position the engine (#33) the mounting plate put the hex bolt M8x40 (#46) through the
bottomof the plate, then put flat washer flat washer Ø8 (#36), lock washer Ø8(#32) and
tighten with the nylon lock nut M8 (#31).
2. Attach the clean oil pipe (#53) to the bottom of the gear pump and secure with clamp (#51).
Lock in this
7
STEP 5: ATTACH HYDRAULIC HOSE
1. Put O ring Ø11x2.5 (#19) on the gear pump connector (#23) and attach the hydraulic hose
(Connector-valve) (#16) to the gear pump connector (#23).
2. Put the O ring Ø17x2.5 (#71) on the connector (#50) and attach the hydraulic hose (#7) to the
end of the connector (#50).
STEP 6: ADD ENGINE OIL
1. Make sure the log splitter is on a level surface.
2. Remove oil fill cap/dipstick to add oil.
3. Refer to the separate owner’s engine manual for the amount needed of SAE10W-30 engine oil;
replace oil fill cap/dipstick.
4. Check engine oil level daily and add as needed.
NOTE: During the break-in period check the engine oil level often.
CAUTION
DO NOT attempt to crank or start the engine before it has been properly filled with the
recommended type and amount of oil. Damage to the log splitter because of failure to follow
these instructions willvoid your warranty.
STEP 7: ADD GASOLINE TO THE ENGINE
1. Use only clean, fresh, regular unleaded fuel with a minimum 85 octane rating.
2. DO NOT mix oil with fuel.
3. Remove the fuel cap and slowly add fuel to the tank. DO NOT overfill allow approximately ¼
inch of space for fuel expansion.
4. Screw on the fuel cap and wipe away any spilled fuel.
8
DANGER
Log splitter engine exhaust contains carbon monoxide, a colorless, odorless, poison gas.
Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy
or weak, get to fresh air immediately.
Operate log splitter outdoors only in a well-ventilated area.
DO NOT operate the log splitter inside any building, enclosure, or compartment.
DO NOT allow exhaust fumes to enter a confined area through windows, doors, vents, or other
openings.
DANGER CARBON MONOXIDE, using a log splitter indoors CAN KILL YOU IN MINUTES.
CAUTION
Fuel and fuel vapors are highly flammable and extremely explosive. Fire or explosion can cause
severe burns or death.
Unintentional startup can result in entanglement, traumatic amputation, or laceration. Only use
regular unleaded gasoline with a minimum 85 octane rating.
DO NOT mix oil and gasoline together.
Fill tank approximately ¼” below the top of the tank to allow for fuel expansion.
DO NOT fill fuel tank indoors or when the engine is running or hot.
DO NOT light cigarettes or smoke when filling the fuel tank.
STEP 8: ADD HYDRAULIC OIL
1. The log splitter needs to be on a flat level surface before adding the hydraulic oil.
2. Remove the oil cap from the hydraulic reservoir.
3. Add 4.49 gallons of hydraulic oil AW32, AW46 & universal hydraulic oil are all acceptable typesof
fluid. Automatic transmission fluid should be used when operating in temperatures
below 32 degrees (all units are tested and have excess oil in the ram).
4. Check the hydraulic oil level.
5. Start engine and use the control lever to extend and retract wedge several times to remove air
from the lines.
6. With the wedge retracted, check hydraulic oil level again and fill if necessary.
WARNING
DO NOT remove the hydraulic oil fill cap when the engine is running or hot. Hot oil can escape
causing severe burns. Always allow the log splitter to cool completely before removing the
hydraulic oil cap. High fluid pressure and temperatures are created in the hydraulic log splitters.
Hydraulic fluid will escape through a pin-size hole opening and can puncture skin and cause
severe blood poisoning. Inspect hydraulic system regularly for possible leaks. Never check for
leaks with your hand while the system is pressurized. Seek medical attention immediately
if injured by escaping fluid. Make sure all fittings are tight and secure before applying pressure.
Relieve system pressure before servicing. Make sure the hydraulic hoses do not touch any hot
surfaces or cutting areas. Hoses need to be positioned where they are clear from the engine and
cutting wedge. To avoid serious bodily injury always inspect the hoses before operating the log
splitter.
9
OPERATION INSTRUCTIONS
WARNING
Before operating or using the log splitter, review the instructions below and all safety information.
Failure to follow these instructions may result in property damage or injury to the operator or
bystanders.
WARNING
ALWAYS use the log splitter for its intended use.
ONLY use the log splitter to split wood logs, length wise with the grain.
NEVER modify, alter, or change the log splitter in anyway, modifications will void the
warranty.
NEVER attach a rope, cable, or other device to the control lever on the log splitter.
ONLY operate the log splitter in daylight.
NEVER leave the log splitter unattended while the engine is running.
DO NOT change the splitting position with the engine running. Contact with the muffler
can causeserious burns.
ALWAYS make sure the beam is in the locked position.
DO NOT let the beam drop as it could crush fingers or cause damage to the log splitter.
NEVER operate or let anyone else operate, the log splitter while under the influence of
alcohol, drugs,or medication.
USING YOUR LOG SPLITTER
1.
2.
3.
4.
DO NOT at any time carry passengers, sit, or stand on the log splitter.
Check the hydraulic oil level and visually inspect all hoses and attachments for problems.
Inspect the engine and make sure the engine oil level is correct.
Before towing the log splitter, the tires need to be fully inflated.
TIRE WARNING
DO NOT over inflate tires. Serious injury can result if tires explode.
DO NOT tow the log splitter if the tires are worn or will not hold air.
DO NOT exceed the maximum 45 MPH towing speed.
5. Refer to the vehicle owner’s manual for proper safety and towing instructions.
TOWING WARNING
Serious injury or death can occur if towing safety rules are not followed.
Always use safety chains, secure, and lock the log splitter to the vehicle hitch before moving. Drive
safely. Be aware of the added length of the log splitter.
Never exceed the maximum travel speed of 45 mph. Never ride or transport cargo on the log
splitter.
Turn off the vehicle before leaving the log splitter unattended. Block the log splitter wheels to
prevent unintended movement.
10
6. The log splitter must have at least seven feet of clearance from combustible material. It
needsto be on a dry and level surface with good footing. Do not work on mud, ice, brush, or
snow. When using the log splitter, the work zone must be always maintained.
NOTE: Serious accidents can happen when other people are allowed inside the work zone.Keep
everyone else outside the work zone while operating the control lever.
7. Always wear safety gear, eye protection, gloves and work boots when operating the log
splitter.
8. Start the engine and make sure the log splitter is on level ground before operating.
NOTE: The hydraulic oil needs to be above 10°F (-12C°) before starting the engine. Cold hydraulic
oil can damage the hydraulic pump.
If outdoor air temperature is below 32°F (0C°)
allow the log splitter to warm up by extending and returning the wedge several times before
splitting wood.
9. Put the support leg in the down position to prevent the log splitter from moving
duringoperation and block both tires.
10. Set the log splitter in either the horizontal or vertical position.
NOTE: HORIZONAL position is used for lighter logs that can easily be loaded onto the beam. The
VERTICAL position is used for either light logs or heavy logs that are difficult to load ontothe beam.
Back injury can result from lifting logs onto the log splitter if proper lifting techniques are not used.
11. Load a log onto the beam against the endplate (Max Log Length-26”).
11
12. Make sure hands are clear from the wedge and crush hazard areas.
CRUSH WARNING
Wedge can cut through skin and break bones. Keep both hands away from wedge and beam slide.
Serious accidents can happen when other people are allowed inside the work zone. Keep
everyone else out of the work zone while operating control lever.
DO NOT wear loose clothing. It can get tangled in moving parts of log splitter. Only use the log
splitter in daylight so you can see what you are doing.
13. Push control lever FORWARD by one hand to split the log.
14. Push control lever BACKWARD by one hand to return wedge to its original position.
CAUTION
If a log gets stuck, embedded, or will not split completely, push the control lever in the reverse
direction and allow the splitter to strip the log from the wedge.
If the log remains stuck, embedded, or will not split, turn the machine off and use a
sledgehammer and crowbar to remove the log.
ALWAYS keep hands clear of the log and wedge while it is retracting.
15. Always keep work zone clean and free of split wood and debris.
12
OPERATION INSTRUCTIONS
13
MAINTENANCE AND STORAGE
WARNING
Improper maintenance and storage of the log splitter may void your warranty.
MAINTENANCE
•
•
•
•
•
•
•
•
Before performing maintenance, the log splitter must be placed in maintenance mode. Turn
off the engine and move the control lever forward and backwards to relieve the hydraulic
pressure.
After performing any maintenance, make sure all guards, shields and safety features are put
back in place before operating the log splitter.
Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE.
Regularly grease axle and wheel bearing area or when needed.
Periodically check all fasteners and hoses for tightness and leaks.
Annually clean and lightly lubricate all moving parts or when needed.
Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.
Never exceed load capacity rating of 30 tons it will damage the log splitter.
What
When
Hoses
Each Use
Hydraulic
Fittings
Nuts and Bolts
Beam
Moving Parts
Each Use
Each Use
Each Use
Each Use
How
Inspect hoses for exposed wire mesh and leaks.
Replace all worn or damaged hoses before startingthe
engine.
Inspect fittings for cracks and leaks. Replace all
damaged fittings before starting the engine.
Check for loose bolts, tighten before operating.
Apply grease to beam surface.
Clear debris from log splitter.
REFER TO THE ENGINE OWNER’S MANUAL FOR ENGINE MAINTENANCE.
IMPORTANT:
If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement
parts that do not meet specifications may result in a safety hazard or poor operations.
STORAGE
•
•
•
Before storing make sure the log splitter is clean and dry for years of trouble-free service.
Lightly lubricate all log splitter surfaces and moving parts to prevent rust.
Store indoors or protected area during severe weather and winter months.
14
TROUBLESHOOTING
PROBLEM
Cylinder rod will not move
SOLUTION: A, D, E, H, J
Slow cylinder rod speed when extending
or
SOLUTION: A, B, C, H, I, K, L
retracting
Wood will not split or splits extremely
slowly
SOLUTION: A, B, C, F, I, K
Engine bogs down during splitting
SOLUTION: G, L
Engine stalls under low load condition
SOLUTION: D, E, L, M
Engine starts problem
SOLUTION: N
Cause
Solution
A-Insufficient oil to pump
Check oil level in reservoir
B-Air in oil
Check oil level in reservoir
C-Excessive pump inlet vacuum
Check pump inlet hose for blockage or
kinks
D-Blocked hydraulic lines
Flush and clean the splitter hydraulic
system
E-Blocked control valve
Flush and clean the splitter hydraulic
system
F-Low control valve setting
Adjust control valve with a pressure
gauge
G-High control valve setting
Adjust control valve with a pressure
gauge
H-Damaged control valve
Return control valve for authorized repair
I-Internal control valve leak
Return control valve for authorized repair
J-Internal cylinder leak
Return cylinder for authorized repair
K-Internally damaged cylinder
Return cylinder for authorized repair
L-Engine Control out of adjustment
Adjust idle control nuts
M-Engine is loaded during idle down mode Use shorter log length (26” or less) to
allow
engine to speed up before contact.
N-Engine operation
Refer to the English owner’s manual
15
SPECIFICATIONs
Ram Force ......................................................................................................... 30 Ton
Cycle Time ..................................................................................................... 13.5 Sec
Wedge Size .........................................................................................8” Harden Steel
Gear Pump ................................................................................................... . 2-Stage
Hydraulic Oil ..................................AW32, AW46, ISO32 or Universal Hydraulic Oil
Amount of Hydraulic Fluid ............................................................................ ….8 Gal
Max. Log Length .................................................................................................... 24”
Hydraulic Cylinder........................................................................... .4-1/4” x 29-3/4”
Max. Pressure ......................................................................................... 3625 PSI
Max. Flow ....................................................................................................... 14 GPM
Wheel Size...........................................................................................16” / 4.80-8
Hitch Type ........................................................................................... 2” Ball Coupler
Max. Towing Speed ....................................................................................... 45 MPH
Manual Start Engine ......................................................................................... 250cc
NOTE: For Engine Details Refer to the Engine Owner’s Manual.
16
PARTS DRAWING & PARTS LIST
17
PARTS DRAWING & PARTS LIST
REF#
DRAWING NO.
DESCRIPTION
1
9101-05010-DX8.8
Hex Bolt M5x10
4
2
3
9121-06010-FH
LSP30B-03000
Inner Hex Cone Point Set Screw
Cylinder
1
1
4
LSP25-00001-DX
Metal Tube
1
5
6
LSP25-00005-DX
LSP25-00004-DX
R Pin
Cylinder Pin
2
1
7
LSP25-00017
8
9
LSP25-06000
LSA22-09000
Connector
Control Valve
2
1
10
LSP25-17000
Combination Connector
1
11
12
LSP25-00002-DX
LSP25-00006-DX
130°Joint
Safety Pin
1
1
13
9206-12000-DX
Nylon Lock Nut M12
7
14
15
LSP30B-02000
9101-14085-DX8.8
Wedge
Hex Bolt M14x85
1
1
16
LSP25-00016
Hydraulic Hose(valve-Pump)
1
17
18
LSP30B-01000
LSP25-05000
19
9901-11x2.5
O Ring Ø11x2.5
2
20
21
LSP25-00010-DX
LSP25-00012-DX
Oil Plug
R Pin Ø12
1
1
22
9901-15x2.5
O Ring Ø15x2.5
2
23
24
LSP25-00014-DX
9101-12100-DX8.8
Gear Pump Connector
Hex Bolt M12x100
1
2
25
LSP30-10001
Gear Pump
1
26
27
LSP25-13000
LSP25-10003
New Oil Bolt
Gear Pump Connector
1
1
28
LSP25-10002
Engine Connector
1
29
30
LSP25-10004-DX
LSP25-10005
Engine Axle Sleeve
Gear Pump Stand
1
1
31
9206-08000-DX
Nylon Lock Nut M8
8
32
33
9306-08000-DX
LSP25-10001
Lock Washer Ø8
Engine
12
1
34
LSP25-10006
Connector Cover
1
35
36
LSP25-14000
9301-08000-DX
Wheel
Flat Washer Ø8
2
8
37
LSP25-00020-FH
Hex Slotted Thin Nut M20
2
38
39
LSP25-00019-DX
LSP25-00007
Angle Connector
Oil Fitter
1
1
40
9404-03030-DX
Cotter Pin Ø3x30
3
Hydraulic Hose (valve-external filter)
Beam
Hitch Pin
QTY
1
1
1
18
REF#
DRAWING NO.
DESCRIPTION
QTY
41
LSP25-00009-DX
Axle Cap
2
42
LSP30-00006
Rubber Washer
1
43
LSP25-10008-FH
Steel Wire Snap Ring for Shaft
1
44
LSP30-03000
Oil Tank
1
45
9301-06000-DX
Flat Washer Ø6
6
46
9101-08065-DX8.8
Hex Bolt M8x65
4
47
9101-06020-DX8.8
Hex Bolt M6x20
6
48
LSP30-15000-DX
Filter Fixed Plate
1
49
LSP25-09000
Oil Return Filter
1
50
LSP25-00007-DX
Connector
1
51
LSP25-00011-DG
Clamp
2
52
N29W-00001
Plate
1
53
LSP25-00018
Oil Pipe
1
54
9301-20000-DX
Flat Washer Ø20
2
56
LSP25-00003-DX
Spring
3
57
9101-08025-DX8.8
Hex Bolt M8x25
4
59
LSP30-07000
Support Leg
1
60
9304-62000-FH
Steel Wire Snap Ring for Shaft Ø62
1
61
LSP25-00008-DX
Safety Pin
2
62
LSP30-04000
Tow Bar
1
63
LSP25-11000-DX
Chain
2
64
9110-08010-DX
Screw M8x10
4
65
9301-12000-DX
Flat Washer Ø12
11
66
Z103
Coupler
1
67
9101-12080-DX8.8
Hex Bolt M12x80
2
68
LSP25-00015-DX
Thick Washer Ø12
2
69
9101-12090-DX8.8
Hex Bolt M12x90
1
70
9306-06000-DX
Lock Washer Ø6
6
71
9901-17X2.5
O Ring Ø17x2.5
2
72
9101-08030-DX8.8
Hex Bolt M8x30
4
73
9404-04036-DX
Cotter Pin Ø4x36
2
74
9206-14000-DX
Nylon Lock Nut M14
1
75
/
Gear Pump Flat Key
1
76
/
Engine Flat Key
1
19
ATTACH THE LOG CRADLE TO THE BEAM WITH THE Ø12 FLAT WASHERAND
M12 LOCK NUT.
LOG CRADLE
Ø12 FLAT WASHER
M12 LOCK NUT
20
ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY
The use of any equipment, including this one, involves the potential risk of injury. Apart from any warranty
claim that might be presented for a claimed defect in material or workmanship of the product, you accept
and assume full responsibility for any and all injuries, damages (both economic and non-economic), and
losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers,
employees, officers, directors, associates, and agents from any and all claims, demands, damages,
rights of action, or causes of action, present or future, whether the same be known or unknown,
anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
This equipment must be used with care by capable and competent individuals under supervision,
if necessary.
WARNING
Do not overfill! Mower should be level
when checking oil in gear box.
some activities might be able to cause
electric shock
Sharp objects may be involved.
Use protective cover during maintenance.
TITAN LIMITED WARRANTY: TERMS, EXCLUSIONS AND LIMITATIONS OF REMEDIES
This product comes with a one (1) year limited warranty that can be found at
www.palletforks.com/warranty.html. Please review the same for all details regarding the
Titan Limited Warranty.
THE TITAN LIMITED WARRANTY FOUND AT WWW.PALLETFORKS.COM/WARRANTY.HTML
IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, EACH
OF WHICH IS HEREBY DISCLAIMED.
21
NEED HELP? CONTACT US FIRST.
1-800-605-7595
[email protected]
www.palletforks.com
© 2021 Titan Brands
22
">
