Fisher & Paykel RS6121VR2K1 Integrated Column Wine Cabinet Installation Guide
Reklama
Reklama
INTEGRATED COLUMN
REFRIGERATOR & FREEZER
RS6121S, RS6121SH, RS7621S, RS7621SH
RS4621F, RS6121F & RS7621F
REFRIGERATOR-FREEZER
RS6121W & RS7621W
WINE CABINET
RS6121V
INSTALLATION GUIDE
NZ AU UK IE EU SG HK
Safety and warnings
Integrated refrigerator & freezer
Integrated refrigerator-freezer
Integrated wine cabinet
Supplied parts
Required parts
Door panel kit
Handle kit
Hinge change kit
Wine display accessories
Tools
Product dimensions
Cabinetry dimensions — Single installation
Cabinetry dimensions — Multiple installation
Stainless steel Door panel dimensions — Single installation
Custom Door panel dimensions — Single installation
Custom Door panel dimensions — Multiple installation
Toe kick dimensions
Installation options
Door clearance
Drawer clearance
Electrical and plumbing
Custom door panel install dimensions
Before installation
Cavity preparation
20
21
21
22
16
17
18
19
23
28
30
12
13
14
15
9
10
11
11
7
8
6
6
4
5
CONTENTS
Appliance preparation
Door panel preparation — Stainless steel panel
Door panel preparation — Custom panel
Door panel preparation — Wine cabinet only
Power and water supply connection
Single installation — Align appliance into cabinetry
Single installation — Secure appliance into cabinetry
Door panel installation
Toe kick installation
Grilles installation
Carbon filter installation
Air flow divider installation
Door covers & Trims installation
Top trim & hinge pocket covers installation
Multiple installation — Appliance preparation
Multiple installation — Join products
Multiple installation — Roll into cabinetry
Multiple installation — Level and secure
Grilles installation
Multiple installation — Top trim & hinge pocket covers installation
Multiple installation — Install trims
Wine display for wine cabinet
Change the door hinges (optional)
Final checklist
47
47
48
49
40
41
43
46
31
33
34
35
37
38
54
55
56
57
50
51
52
53
58
63
3
4
WARNING!
Electric Shock Hazard
Failure to follow this advice may result in electrical shock or death.
• Read and follow the safety and warnings outlined in this User guide before operating this appliance.
WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: panel edges may be sharp.
• Do not put fingers in the drawers when closing.
WARNING!
Tip Hazard
• This product may tip until it is fully installed.
Keep children away and take care. Failure to follow this advice may result in injury.
• This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
To ensure that the appliance is stable under all loading conditions:
• The anti-tip bracket and fittings supplied must be installed by a professional installer according to the installation steps in this guide.
SAFETY AND WARNINGS
READ AND SAVE THIS GUIDE
WARNING!
z z z
To avoid hazard, follow these instructions carefully before Installing or using this appliance.
Please make this information available to the persons installing the appliance.
Assume all electrical parts are live.
Disconnect power supply before servicing and installation.
z z z z z z
BEFORE INSTALLATION
The appliance has front and rear rollers to easily move forward and backward. Do not move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher.
The appliance must be installed by a qualified installer, or Fisher and Paykel trained and supported service technician to avoid faulty electrical and plumbing connections.
All connections for electrical power and grounding must comply with local codes and ordinances and be made by licensed personnel when required.
Avoid installation of the appliance/s under a ground fault circuit interrupter (GFCI).
Ensure the appliance is installed properly. Improper installation that results in appliance failure is not covered under the appliance warranty.
z z z z z z z z
UNPACKING
The appliance is heavy and requires at least two persons to move and install.
Remove the installation kit (internal box) and trims kit (external box) while the product is still on the pallet.
Avoid scratching the surface of your appliance when moving or installing.
Keep the appliance stable and door closed to prevent tipping over when moving to the installation location.
Ensure the feet of the appliance are retracted before moving to the installation location.
If the appliance is damaged, contact your Fisher and Paykel dealer.
Ensure all components and accessories are complete. Refer to 'Before installation'.
Record the default Wifi password, and the model and registration numbers for future servicing or repair of your appliance.
z z
ELECTRICAL/PLUMBING
Alternatively, electrical and water supply connections for these appliances can be located in an adjacent area or unit (cabinet or cupboard) that are easily accessible in case of repair or disconnection.
Ensure an isolating switch is available if electrical connection is not accessible.
SAFETY AND WARNINGS
z z z z z z z z
INSTALLATION
The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load.
Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the appliance tipping forward when the door is open.
Ensure the door of the appliance is closed when rolling into the cabinetry.
Ensure the power cord is not run over or damaged when rolling the product into the cabinetry.
For flush installation, ensure the door panels are installed flush with cabinetry front surface. Ensure the appliance is properly is centreed.
All four corners of the appliance must be supported firmly on the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
Use low speed, low torque setting when using a powered driver for the screws when fixing or aligning the product.
Open the appliance door to remove the alignment brackets from both sides of the appliance, and then re-tighten the screws.
z z z
Stainless steel panel
Protect the finish of the Fisher and Paykel Stainless Steel door panels from any scratch or damage.
Remove the blue tape attached to inner edges of the door panels after the handles are installed.
We recommend to load the shelves in the appliance door with weights to ensure an accurate door panel gap width. Load 15kg for RS61 models, and 20kg for RS76 models.
z z z z
Custom panel
If using Custom door panels, ensure they are prepared as per 'Custom door panel install dimensions' section.
The thickness of the custom door panel can vary as long as the screws do not penetrate beyond the full depth of the door panel, and as long as the overall weight of door panel does not exceed the allowable weight. Refer to 'Door panel dimensions' for maximum door panel weight of your product.
Do not place the handle holes in marked areas to avoid clashing with panel attachment brackets.
Minimum panel thickness where screw hole is drilled must be 16mm.
z
Changing the door hinge (optional)
Door hinges are interchangeable for each model. A hinge change kit is available and can be purchased separately if you prefer to change from ‘right hinge door’ to ‘left hinge door’ or vice versa.
Freezer, 46cm
RS4621FLJK*
& RS4621FRJK*
INTEGRATED REFRIGERATOR & FREEZER
Freezer, 61cm
RS6121FLJK*
& RS6121FRJK*
Freezer, 76cm
RS7621FLJK*
& RS7621FRJK*
Refrigerator, 61cm
RS6121SLK*, RS6121SLHK*,
RS6121SRHK* & RS6121SRK*
Refrigerator, 76cm
RS7621SLK*, RS7621SLHK*,
RS7621SRHK* & RS7621SR*
Left or Right hinged door available for each model.
5
6
INTEGRATED REFRIGERATOR-FREEZER
Refrigerator-Freezer, 61cm
RS6121WLUK* & RS6121WRUK*
Refrigerator-Freezer, 76cm
RS7621WLUK* & RS7621WRUK*
INTEGRATED WINE CABINET
Wine Cabinet, 61cm
RS6121V2LK* & RS6121V2RK*
Left or Right hinged door available for each model.
INSTALLATION KIT (INTERNAL BOX)
Door panel attachment kit
SUPPLIED PARTS
TRIMS INSTALL KIT (EXTERNAL BOX)
Refrigerator or Freezer
Side bracket (12) Bracket slider (12)
Anti-tip bracket assembly
Side spacer bracket (12)
M5x12 Cross-head screw (44)
Door panel side cover (2)
Wine Cabinet
Anti-tip bracket (1) Masonry plug (5) 10-12x35mm crosshead screw (5)
Install fasteners kit
Door panel side cover (2)
Refrigerator-Freezer
Depth alignment gauge (4)
Miscellaneous parts
Barbed plug (2) 8Gx16 Countersunk screw (7)
Upper door panel side cover (2) Lower door panel side cover (2) Drawer top trim (1)
Hinge limiting pin (3) Air toe kick seal (1) Flow divider cap (1)
7
INTEGRATED COLUMN
REFRIGERATOR & FREEZER
RS6121S, RS6121SH, RS7621S, RS7621SH
RS4621F, RS6121F & RS7621F
REFRIGERATOR-FREEZER
RS7621W & RS7621W
WINE CABINET
RS6121V
INSTALLATION GUIDE
NZ AU UK IE EU SG HK
Installation guide
SUPPLIED PARTS
MISCELLANEOUS ITEMS (MI) PACK
SERVICE & WARRANTY
SERVICE ET GARANTIE
ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保 修 和 维 修
݉ଡ଼ڸߴঔ
Service & Warranty
INTEGRATED
REFRIGERATOR & FREEZER
INTEGRATED REFRIGERATOR
RS6121S, RS6121SH, RS7621SH & RS7621S
INTEGRATED FREEZER
RS4621F, RS6121F & RS7621F
USER GUIDE
NZ AU UK IE SG HK
User guide
WATER CONNECTION KIT
Supplied in models with Ice & Water function only
( RS6121SH, RS7621SH, RS4621F, RS6121F, RS7621F, RS7621W & RS7621W)
Water filter comes preinstalled on this product.
Air carbon filters (2)
#862755
For Wine Cabinet only
REQUIRED PARTS
STAINLESS STEEL TOE KICK PANEL
Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer.
Visit fisherpaykel.com for more information.
Toe kick panel (1)
Standard toe kick height is 102mm for standard stainless steel door panel.
For Custom door panel installation, a toe kick 50–152mm must be fitted and adjusted accordingly.
An extra bottom grille is required when you use 50mm toe kick height.
You can purchase the extra bottom grille (847542P) online at fisherpaykel.com.
INSTALL JOINER KIT
Used for combined installation of multiple appliances. Supplied in selected appliances only
(Freezer and Wine Cabinets). For other models, the joiner kit (AJ-RS84LR) can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.
Joiner fastener kit
Collet locking clip (1) 6mm Stainless steel braided hose with
7/16-24 UNS thread (1)
6.35mm Adaptor (2)
Joiner Sleeve (2) Screw WSH M6 (1) M6 Hex Nut (1) Bolt M5 HEX (2)
Flange Joiner Trim (2)
Aluminium center trim (1)
8
REFRIGERATOR OR FREEZER
Stainless steel door panel kit
RS46
RS61
RS76
RH
RD4621R4D
RD6121R4D
RD7621R4D
LH
RD4621L4D
RD6121L4D
RD7621L4D
DOOR PANEL KIT
REFRIGERATOR-FREEZER
Stainless steel door panel kit
RS61
RS76
RH
RD6121WRD
RD7621WRD
LH
RD6121WLD
RD7621WLD
WINE CABINET
Stainless steel door panel kit
RS61
RH
RD6121VR4
LH
RD6121VL4
Custom door panel
8Gx16 Mush washer screw (32)
Custom door panel
8Gx16 Mush washer screw (48) 8Gx16 Mush washer screw (32)
Custom door panel
The Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of the Wine Cabinet.
M5x12 Cross-head screw (44)
Included in Installation kit
M5x12 Cross-head screw (44)
Included in Installation kit
M5x12 Cross-head screw (44)
Included in Installation kit
Custom door panels must be supplied by the customer to match their cabinetry. Stainless steel door panels are not supplied and must be purchased separately through an authorised Fisher and Paykel dealer.
Take note of the part numbers above to ensure you are ordering the correct door panel set. Visit fisherpaykel.com for more information.
9
CONTEMPORARY
Aluminium/Black square fine handle set
Square fine handle
(1)
M5x25 Hex screw
(4)
MODEL
REFRIGERATOR/FREEZER
WINE CABINET
RS61 REFRIGERATOR-FREEZER
RS76 REFRIGERATOR-FREEZER
DESCRIPTION
AHD5-RDSF
AHD5RD6121W
AHD5RD7621W
HANDLE KIT
Stainless steel round flush handle set
PROFESSIONAL
Round flush handle
(1)
M5x25 Hex screw
(4)
MODEL
REFRIGERATOR/FREEZER
WINE CABINET
RS61 REFRIGERATOR-FREEZER
RS76 REFRIGERATOR-FREEZER
DESCRIPTION
AHP3-RDSF
AHP3-RD6121W
AHP3-RD7621W
Aluminium round handle set
Round handle
(1)
M5x25 Hex screw
(4)
MODEL
REFRIGERATOR/FREEZER
WINE CABINET
RS61 REFRIGERATOR-FREEZER
RS76 REFRIGERATOR-FREEZER
DESCRIPTION
AHSRDSF
AHSRD6121W
AHSRD7621W
Classic handle set
M5x25 Hex screw
(4)
MODEL
REFRIGERATOR/FREEZER
WINE CABINET
RS61 REFRIGERATOR-FREEZER
RS76 REFRIGERATOR-FREEZER
DESCRIPTION
AHCLRDSF
AHCLRD6121W
AHCLRD7621W
The handle kit is not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.
For Refrigerator-Freezer models, each handle kit includes two (2x) handles for door and drawer panels, and M5x25 hex screws (8x).
10
HINGE CHANGE KIT
Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer.
Visit fisherpaykel.com for more information. Select among the hinge change kit options below:
HINGE KIT
REFRIGERATOR OR FREEZER
48CM 61CM 76CM
WINE CABINET
61CM
REFRIGERATOR-FREEZER
61CM 76CM
WINE DISPLAY ACCESSORIES
Accessories are not supplied with the appliance. A wine display kit and a label kit are sold separately and can be purchased online at fisherpaykel.com.
Wine display kit
848186 848188 848190 864757P 848184P 848184P
2x 1x
Left to Right hinge
Handle assembly (1)
848185 848187 848189 864759P 848183P 848183P
Right to Left hinge
Cradle assembly (4)
Left to Right hinge kit
Top hinge pocket
RH (2)
Right to Left hinge kit
K05 bottom adaptor* bracket RH (1)
Top alcove bracket
RH (2)
K05 top adaptor* bracket RH (1)
Spacer (1)
Wine label kit
Top hinge pocket
LH (2)
K05 bottom adaptor* bracket LH (1)
Top alcove bracket
LH (2)
K05 top adaptor* bracket LH (1)
Label (14) Pencil (1)
Top grille (1)
Supplied in Hinge change kit for Refrigerator & Freezer and
Wine Cabinet only.
*Top and bottom adaptor brackets for Wine Cabinet different from illustration.
11
Required tools
Not supplied and must be provided by the installer.
Powered driver Flathead screwdriver Ruler
Cross-head screwdriver
Cutter (1) T20 star-head screwdriver
(Used for changing hinge)
8mm socket wrench
(Used for joiner bolts)
13mm socket wrench
(Used for drawer panel of
Refrigerator-Freezer model)
Hacksaw
(For cutting air flow divider to length)
TOOLS
Supplied tools
Spanner M4 hex key
10mm spanner
(Used for multiple installation)
3mm allen key
(Used for multiple installation)
Hand truck
12
REFRIGERATOR OR FREEZER
B C
PRODUCT DIMENSIONS
REFRIGERATOR-FREEZER
B C B
WINE CABINET
C
A A
E
D
PROFILE FRONT
PRODUCT DIMENSIONS
A Overall height
B Overall width
C Overall depth (excluding door panel)
D Depth of toe kick (measured from back of door panel)
E Height from floor to bottom of Stainless steel door/drawer panel
F Height from floor to top of drawer panel (Refrigerator-Freezer only)
G Gap between door and drawer panels (Refrigerator-Freezer only)
PRODUCT WEIGHT (WITHOUT PACKAGING)
Refrigerator or Freezer
Refrigerator-Freezer
Wine cabinet
46cm model for Freezer only. Wine Cabinet available in 61cm only.
FRONT
A
G
F
E
D
PROFILE
46CM
MM
2134
451
610
73–102
102
874
—
KG
101
—
—
FRONT
61CM
MM
2134
603
610
73–102
102
874
3
KG
117
142
152
E
D
PROFILE
76CM
MM
2134
756
610
73–102
102
874
3
KG
134
163
—
13
CABINETRY DIMENSIONS — SINGLE INSTALLATION
C
A
B
ISOMETRIC
CAVITY DIMENSIONS
A Overall height of cavity
B Overall width of cavity
C Minimum overall depth of cavity* d Minimum gap from edge of door panel to cabinetry e Minimum required finished return
*Assumes a door panel thickness of 19mm.
14 Illustrations may differ from your purchased appliance.
E
D
UNFRAMED
Aligns appliance with cabinetry
Flush with front of cabinetry
PLAN
E
D
FRAMED
Aligns appliance with frame of cabinetry
46CM
MM
2134
457
635
3
102
61CM
MM
2134
610
635
3
102
76CM
MM
2134
762
635
3
102
DUAL INSTALL
CAVITY DIMENSIONS
A Overall height of cavity
B Overall width of cavity
C Minimum overall depth of cavity*
*Assumes a door panel thickness of 19mm.
TRIPLE INSTALL
CAVITY DIMENSIONS
A Overall height of cavity
B Overall width of cavity
C Minimum overall depth of cavity*
*Assumes a door panel thickness of 19mm.
A
DUAL INSTALL
CABINETRY DIMENSIONS — MULTIPLE INSTALLATION
TRIPLE INSTALL
C C
A
B
B
107CM
MM
2134
1067
635
168CM
MM
2134
1677
635
122CM
MM
2134
1220
635
183CM
MM
2134
1829
635
137CM
MM
2134
1372
635
152CM
MM
2134
1524
635
198CM
MM
2134
1982
635
213CM
MM
2134
2134
635
229CM
MM
2134
2286
635
Illustrations may differ from your purchased appliance.
15
STAINLESS STEEL DOOR PANEL DIMENSIONS — SINGLE INSTALLATION
REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER
A
B
C
DOOR PANEL DIMENSIONS
A Height of door panel
C Width of door panel
C Depth of door panel*
*Excluding handle
DOOR PANEL WEIGHT
Weight of Refrigerator or Freezer door panel
Weight of Wine cabinet door panel
A
A
46CM
MM
2029
451
19
B
61CM
MM
2029
603
19
C
46CM
KG
20
—
61CM
KG
25
8
B
76CM
MM
2029
756
19
76CM
KG
30
—
DOOR PANEL DIMENSIONS
A Height of top door panel
B Height of bottom drawer panel
C Width of door panel
D Depth of door panel*
*Excluding handle
DOOR PANEL WEIGHT
Weight of top door panel
Weight of bottom drawer panel
C
D
61CM
MM
1254
772
603
19
61CM
KG
9
6
76CM
MM
1254
772
756
19
76CM
KG
10
7
16 Illustrations may differ from your purchased appliance.
CUSTOM DOOR PANEL DIMENSIONS — SINGLE INSTALLATION
REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER
A
A
A
B
B
B
C
C C D
DOOR PANEL DIMENSIONS
A Height of door panel
C Width of door panel
C Depth of door panel*
*Excluding handle
46CM
MM
1978–2080
451 min 16–max 25
61CM
MM
1978–2080
603 min 16–max 25
76CM
MM
1978–2080
756 min 16–max 25
DOOR PANEL DIMENSIONS
A Height of top door panel
B Height of bottom drawer panel
C Width of door panel
D Depth of door panel*
*Excluding handle
61CM
MM
1254
721–822
603 min 16–max 25
76CM
MM
1254
721–822
756 min 16–max 25
DOOR PANEL WEIGHT
Weight of Refrigerator or Freezer door panel
Weight of Wine cabinet door panel
46CM
KG max 20
—
61CM
KG max 25 max 25
76CM
KG max 30
—
DOOR PANEL WEIGHT
Weight of top door panel
Weight of bottom drawer panel
61CM
KG max 15 max 9
76CM
KG max 18 max 11
For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance.
For all models, maximum panel weight must not be exceeded.
Illustrations may differ from your purchased appliance.
17
CUSTOM DOOR PANEL DIMENSIONS — MULTIPLE INSTALLATION
DUAL INSTALL
The illustrations below are examples of custom door panels of different combinations for dual installation. Minimum gaps of 3mm must be retained between door panel side edges and cabinetry regardless of door panel widths.
TRIPLE INSTALL
The illustrations below are examples of custom door panels of different combinations for triple installation. Minimum gaps of 3mm must be retained between door panel side edges and cabinetry regardless of door panel widths.
C C C C C C C
C C
A
A
DIMENSIONS
A Height of door panel
C Width of door panel c Minimum clearance between door panels and cabinetry
*Excluding handle
B B
46CM
MM
2029
452
3
61CM
MM
2029
605
3
76CM
MM
2029
757
3
DIMENSIONS
A Height of door panel
C Width of door panel c Minimum clearance between door panels and cabinetry
*Excluding handle
B B B
46CM
MM
2029
454
3
61CM
MM
2029
605
3
76CM
MM
2029
757
3
18 Illustrations may differ from your purchased appliance.
TOE KICK DIMENSIONS
Custom toe kick options
A
A
B
SINGLE INSTALL
SINGLE INSTALL
STAINLESS STEEL/CUSTOM PANEL
A Height of toe kick*
B Width of toe kick
DUAL INSTALL
STAINLESS STEEL/CUSTOM PANEL
A Height of toe kick* b Width of toe kick
TRIPLE INSTALL
STAINLESS STEEL/CUSTOM PANEL
A Height of toe kick*
B Width of toe kick
*Standard toe kick height is 102mm for any install options.
B
DUAL INSTALL
46CM
MM
102
454
92CM
MM
50–152
912
168CM
MM
50–152
1674
A
B
TRIPLE INSTALL
61CM
MM
102
606
183CM
MM
50–152
1826
76CM
MM
102
759
107CM 122CM
MM MM
50–152
1064
50–152
1216
213CM
MM
50–152
2131
73mm–102mm toe kick clearance measured from rear of door panel
102mm toe kick height
152mm toe kick height
51mm toe kick height
(with extra lower grille attached)
137CM
MM
50–152
1368
152CM
MM
50–152
1521
229CM
MM
50–152
2283
Illustrations may differ from your purchased appliance.
19
SINGLE INSTALL
WALL WALL
INSTALLATION OPTIONS
MULTIPLE INSTALL
WALL WALL WALL WALL
100mm
WALL WALL WALL WALL
WALL WALL
60mm
WALL WALL
WALL WALL
WALL WALL
The illustrations above show acceptable installation options with reference to the door opening range and partition (optional). Be aware of clashing (circled) of doors or handles when opening at the same time.
If installing a partition between the appliances, ensure there is enough clearance to avoid doors/handles from interfering with each other when opening or closing.
If necessary, use a hinge limiting pin to restrict door opening rotation to 90°. Refer to 'Door clearance' for more information.
20 Illustrations may differ from your purchased appliance.
DOOR CLEARANCE DRAWER CLEARANCE
These dimensions apply to Refrigerator-Freezer models only.
C
B
LIMITED INTERNAL ACCESS
Wall
A
A
FULL INTERNAL ACCESS
Insert hinge limiting pin
Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top and bottom door hinges.
The hinge limiting pin limits door swing to 90°.
For Refrigerator-Freezer models, the hinge limiting pins are inserted into the boreholes of the top and bottom hinges of top door.
DIMENSIONS
A Width of door (90° open) measured from front of door
B Minimum door clearance to adjacent wall*
(115°—full internal access)
C Minimum door clearance* to adjacent wall*
(90°—reduced internal access)
A
46CM
MM
508
292
110
61CM
MM
660
356
110
76CM
MM
813
419
110
DIMENSIONS
A Maximum drawer extension when open
(including handle)*
B Maximum drawer extension when open
(excluding handle)
*Assumes handle depth of 41mm
B
61CM
MM
461
420
76CM
MM
461
420
Illustrations may differ from your purchased appliance.
21
A
ELECTRICAL AND PLUMBING
Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall.
C
Alternative locations for connection at rear of cavity
SUPPLY AREA DIMENSIONS
A Overall height of supply area
B Overall depth of supply area
C Width of notch in supply area (both sides)
D Height of sides of supply area (both sides)
ELECTRICAL SPECIFICATIONS
Supply
Service
230 VAC, 50 Hz
10 amp circuit
Socket 3-pin earthing-type
PLUMBING SPECIFICATIONS
Supply 12.7mm BSP Stainless steel braided hose with adaptor
Pressure min 150kPa–max 827kPa @ 20°C
22 Illustrations may differ from your purchased appliance.
D B
A
C
MM
229
25
13
127
POWER CORD
A Total length exiting from left side of appliance (excluding plug)
B Total length exiting from right side of appliance (excluding plug)
WATER HOSE
C Total length exiting from left side of appliance
D Total length exiting from right side of appliance
46CM
MM
1385
1411
46CM
MM
2271
1956
B
D
61CM
MM
2196
1878
61CM
MM
1809
1835
76CM
MM
1733
1759
76CM
MM
1733
1759
CUSTOM DOOR PANEL INSTALL DIMENSIONS
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation, download the folder from http://thekitchentools.fisherpaykel.com.
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
33
226 88
51
18x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets
451
46CM FREEZER
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
23
33
203
302
88
51
CUSTOM DOOR PANEL INSTALL DIMENSIONS
203
33
378
88
51
22x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets.
24
603 single install
605 dual install
61CM REFRIGERATOR OR FREEZER
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
756 single install
758 dual install
76CM REFRIGERATOR OR FREEZER
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
CUSTOM DOOR PANEL INSTALL DIMENSIONS
For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance.
203
33
302
88
51
22x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets.
603 single install
605 dual install
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
61CM WINE CABINET
415
25
CUSTOM DOOR PANEL INSTALL DIMENSIONS
z
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
33
203
302
88
51
10x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets.
33
203
302
83
51
603 single install
605 dual install
61CM REFRIGERATOR-FREEZER
TOP DOOR PANEL
603 single install
605 dual install
61CM REFRIGERATOR-FREEZER
DRAWER PANEL
Cutouts in the hanging bracket are applicable for
Fisher and Paykel handles only.
If locating a custom handle in the shaded area shown above, ensure handle screw heads are countersunk into the back of the door panel to avoid interference with the hanging bracket.
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
26
CUSTOM DOOR PANEL INSTALL DIMENSIONS
z
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
203
33
378
756 single install
758 dual install
76CM REFRIGERATOR-FREEZER
TOP DOOR PANEL
88
51
10x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Ensure handle is mounted
65mm from edge of panel to the centre—this will avoid interference with bracket.
33
203
378
83
51
756 single install
758 dual install
76CM REFRIGERATOR-FREEZER
DRAWER PANEL
Cutouts in the hanging bracket are applicable for
Fisher and Paykel handles only.
If locating a custom handle in the shaded area shown above, ensure handle screw heads are countersunk into the back of the door panel to avoid interference with the hanging bracket.
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
27
BEFORE INSTALLATION
Checking your cabinetry
Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity dimensions' for the correct measurements.
z z z z z z z
Check the power supply and water connections
Ensure that there is a separate power socket for each appliance.
Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance.
For power requirements, refer to the information on the serial plate.
Ensure your appliance is properly grounded.
Connect your appliance to an electrical supply with the fitted plug and lead.
If power connection is located behind the appliance, we recommend to install an isolating switch to a location that is easily accessible to the user for repair or disconnection.
Follow local codes and ordinances when installing the appliance.
Checking your appliance
Unpack your appliance following the steps printed on the packaging box. Ensure your appliance is the correct model as your order. Ensure components and install kits are complete.
Remove the trims kit from the back of the appliance. Refer to 'Supplied parts'
— Trims install kit for parts included in the box.
TED C
INTEGRA
164B 1 GB EU
Remove the installation kit and miscellaneous items kit from inside the appliance.
28 Illustrations may differ from your purchased appliance.
Removing pre-installed parts
BEFORE INSTALLATION
Moving your appliance
Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. You need at least two persons to move this appliance.
Top trim
Disengage one end of the top trim from dual lock strips on the non-hinge side of the appliance.
Slide the top trim out from the hinge pocket of the appliance.
Top door extrusion
Unclip the trim caps of the top extrusion carefully from both ends of the top of the door.
Ensure the magnet remains in place and not damaged as this will affect the operation of the appliance.
1 Remove the brackets from the non-hinge side of the pallet.
Top grille*
Open the door and remove hinge pocket cover using a flat head screwdriver in the slot.
Open the water filter hatch on the bottom grille and unscrew the #8x16 screw.
Remove the bottom grille by unscrewing the #8x16 screws from both ends of the grille.
*Top grille for Refrigerator-Freezer different from illustration.
Bottom grille
The bottom grille is detachable via magnets.
2
Hand truck
Tilt the appliance slightly forward and insert the hand truck between pallet and appliance.
3
Strap
Restrain the appliance with strap and remove the remaining brackets. Use corner posts while strapping to avoid pinching of side trims.
Toe kick mounting plate
Remove the screws to detach the toe kick mounting plate.
Air flow divider
Remove the screw to detach the air flow divider.
Set aside all the removed parts to reuse later.
4
Tilt backward to load the appliance onto the hand truck and set aside the pallet.
Push the hand truck to the installation location.
Illustrations may differ from your purchased appliance.
29
CAVITY PREPARATION
Anti-tip bracket assembly kit
Attaching the anti-tip bracket
Anti-tip bracket (1x)
Masonry plug (4x)
#10x40 cross-head screw
(4x)
Tools
1 overhead cabinetry
A back wall
4 z
Measure the height ( A ) of the attachment location from the floor to the alcove return.
The height ( A ) must not exceed
2138mm to ensure the appliance does not tip over during installation.
5
Cross-head screwdriver
Floor
PROFILE VIEW
Powered drill
2
Pencil
3 min
197mm
30 Illustrations may differ from your purchased appliance.
bracket
B z
Mark a horizontal line ( B ) at the back wall.
Ensure there is a stud behind the wall.
Place the bracket to the backwall. Align the undersurface of the bracket along the marked line.
Mark screw hole locations, and drill screw holes with powered drill.
For solid wall installation
Drill holes suitable to the size of the masonry plugs.
Hammer 10x30mm masonry plugs into wall until flush. Fix bracket to wall with
#10x40mm cross head screws, and screw tightly.
For plaster board wall
Fix the anti-tip bracket to the wall with
#10x40mm cross head screws, and screw tightly with a screwdriver. z
When rollng the appliance into the cabinetry, ensure the anti-tip bracket overlaps the back edge of the appliance.
The bracket must overlap the appliance by a minimum 180mm for a secure hold. z
If minimum 180mm overlap cannot be achieved, install a solid spacer to the wall stud behind the bracket.
Be careful not to run over the power cord when rolling in the appliance.
APPLIANCE PREPARATION
Tools
M8 hex key
13mm spanner
Removing the hanging brackets
M8 washer
13mm socket wrench
1
M8 nut
Remove the M8 nut and M8 washer from the M8 screw at the top of the door using the supplied hex key and spanner.
3
3mm
M8 screw
Loosen the M8 screws by 3mm.
2 Remove the hanging bracket and set aside to use later.
4
For Refrigerator-Freezer:
Repeat steps 1 – 3 to remove the bracket of the drawer. Use a socket wrench to loosen the
M8 nut.
Illustrations may differ from your purchased appliance.
31
Install fasteners kit
Attaching the barbed plugs
Barbed plugs (2x)
Cabinet depth alignment gauge
(4x)
Tools
Cross-head screwdriver
Attaching the depth alignment gauges
APPLIANCE PREPARATION
Before rolling into the cavity, insert a barbed plug into the large holes at the top right and left sides of the appliance.
The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance.
Loosen the right and left screws at the top and bottom sides of the door.
Locate the alignment gauges at correct orientation to the right and left screws.
Left Right z
Place the alignment gauge by inserting the screw head through the keyhole of the gauge.
Push the alignment gauge down to lock the position.
Tighten the screw just enough to firmly hold the gauge.
The alignment gauges are only temporary and must be removed after installation.
For multiple product installation information, refer to page 50.
32 Illustrations may differ from your purchased appliance.
Door handle kit
M5x25 Hex screw
(4x)
Door panel attachment kit
DOOR PANEL PREPARATION — STAINLESS STEEL PANEL
Attaching the brackets Attaching the handle
Remove the protective film around the handle attachment area before installing the handle. Protect the finish of the door panel to avoid damage or scratches to the surface.
hanging bracket side bracket
For Refrigerator/Freezer/Wine cabinet
Remove the plastic plugs from handle holes (4x) of the door panel.
Align the handle to the holes and secure with M5x25 hex screws.
Side bracket
(12x)
Bracket slider
(12x)
Bracket spacer
(12x)
Door panel kit
8Gx16 Mush washer screw (32x)
Tools
Powered driver
For Refrigerator-Freezer
Remove the plastic plugs from handle holes (4x) of the top door panel.
Align the handle to the holes and secure with M5x25 hex screws.
Secure the handle to the handle holes of the drawer door panel with M5x25 hex screws. z z
For Refrigerator/Freezer/Wine cabinet
Secure the top hanging bracket to the screw holes of the door panel with 8Gx16
Mush washer screws.
6x screws for 46cm Column
10x screws for 61cm or 76cm Column
Secure the bracket spacer, side bracket and bracket slider (in order as illustrated) to the screw holes on both sides of the door and drawer panels with 8Gx16 mush washer screws. The side bracket should be able to move freely horizontally and vertically.
bracket spacer side bracket bracket slider right side of panel left side of panel top hanging bracket side bracket bottom hanging bracket
For Refrigerator-Freezer z
Secure the top hanging bracket to the screw holes of the door panel with 8Gx16
Mush washer screws.
10x screws for 61cm or 76cm Column
Secure the bottom hanging bracket to the screw holes of the drawer door panel with
8Gx16 Mush washer screws.
Secure the bracket spacer, side bracket and bracket slider (in order as illustrated) to the screw holes on both sides of the door and drawer panels with 8Gx16 mush washer screws.
Remove the blue tape attached to the inner edges of the door panel after the handles are installed.
Illustrations may differ from your purchased appliance.
33
Door handle kit
M5x25 hex screw
(4x)
Door panel attachment kit
Side bracket
(12x)
Bracket slider
(12x)
Bracket spacer
(12x)
DOOR PANEL PREPARATION — CUSTOM PANEL
Attaching the handle
Refer to 'Custom Door panel dimensions' for correct screw hole positions on the door panel.
Attaching the brackets
Refer to 'Custom Door panel dimensions' for correct screw hole positions on the door panel. marked line top hanging bracket side bracket
For Refrigerator/Freezer/Wine cabinet
Secure the door handle to the handle holes of door panel with M5x25 hex screw .
For all models
Mark a line across the centre of the custom door panel.
Align the ‘V’ notch at the top of the bracket to the centreline.
Secure the top hanging bracket to the screw holes of the refrigerator custom door panel with M5x12 cross-head screws.
For Refrigerator-Freezer
Secure the handle to the handle holes of the top door panel with M5x25 hex screw .
M5x12 cross-head screw (44x)
Tools
Powered driver
Secure the handle to the handle holes of the drawer door panel with M5x25 hex screw.
top hanging bracket side bracket
Bottom hanging bracket
For Refrigerator-Freezer
Secure the bottom hanging bracket to the screw holes of the drawer door panel with
M5x12 cross-head screws.
Ensure the door and drawer handles do not interfere when attaching the side attachment brackets.
34 Illustrations may differ from your purchased appliance.
Installation kit
DOOR PANEL PREPARATION — WINE CABINET ONLY
Attaching the long glass trims
Glass trims are attached to cover the gap between the Stainless steel door panel and glass panel.
Long trim (2x)
Tools
Cutter
1 long trim red protective film
Peel off a small portion of red protective film from one end of the long trim.
2 hanging bracket
Do not exceed past this line long trim z
Attach the peeled portion of the trim starting from the top of the flange on one side of the door panel cutout.
Ensure the trim does not overlap the hanging bracket.
Align the trim flush with inside edge of the flange.
flange
3
Cut excess length of trim along this line
Continue attaching the long trim for the length of the door panel cutout, peeling off the film as you go.
Cut-off the excess length of the bottom end of the long trim.
Repeat all steps on the other side of door panel cutout.
Illustrations may differ from your purchased appliance.
35
Installation kit Attaching the short glass trims
DOOR PANEL PREPARATION — WINE CABINET ONLY
1
Place the short trim along the length of the top of door panel cutout across the top ends of the long trims. ( A )
3
Short trim (2x)
Tools
Cutter long trim
2
Cut both ends of the short trim to length.
Peel off a small portion of red protective film from the short edge.
4 short trim short edge long edge short trim
Attach the peeled portion starting from one end of flange perpendicular to top end of long trim.
long trim
Continue attaching the short trim for the length of the top of door panel cutout, peeling off the film as you go.
Ensure the trim is aligned flush to inside edge of flange.
Attach the remaining peeled portion of short trim to the flange perpendicular to top end of the other long trim.
Repeat steps 1–4 to the bottom of door panel cutout.
36 Illustrations may differ from your purchased appliance.
Water fittings kit
Collet locking clip (1x)
POWER AND WATER SUPPLY CONNECTION
Connecting to water supply
Ensure the door of the appliance is closed before rolling into the cabinetry. Push the appliance carefully towards the front of the cabinetry close enough to allow access at the back for power and water connection. Ensure an isolating tap is available if water supply is not easily accessible.
1 braided hose
Connect one end of a braided water hose to the water tap.
Flush water through the hose prior to connection to the appliance to remove any debris in the hose.
1/2 BSP Stainless steel braided hose with 7/16-24 UNS thread (1x)
2
Insert the other end of the braided hose through a hole at the rear of the plinth and push all the way to the front of the appliance.
5
Insert the tube end of the adaptor fully into the PLV at the bottom front of the appliance.
16mm Adaptor (2x) PLV
3 Pull the hose to the front of the appliance.
6 locking clip
Secure the connection with a locking clip between the PLV and hose end of the adaptor.
4
Connecting to power supply
Connect an 6mm adaptor to the braided hose. z
At the back of your appliance, connect the power plug to the power outlet
(115VAC, 60Hz).
You will hear a chime sound when the appliance is powered on.
When powered on for the first time, your appliance will default to
Install mode. z
Once installation is complete, unlock the control panel and hold Compartment button for four seconds to start cooling.
Refer to your ‘User guide’ for more information on activating your appliance.
Illustrations may differ from your purchased appliance.
37
Tools
Cross-head screwdriver
Ruler
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY
For multiple product installation information, refer to page 50.
Pushing into the cabinetry
180mm z z
Roll the appliance carefully into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance.
Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold.
Be careful not to run over the water hose and power cord when rolling in the appliance.
Pencil
Aligning the depth gauges z
On the 'Cabinet depth alignment' side of the depth gauges, mark the step on both sides of the door based on the thickness of the door panel.
Example illustration show the door panel thickness 25.4mm marked on the gauges.
Left Right
Check if the gaps between appliance and cabinetry side walls are even on left and right sides.
38 Illustrations may differ from your purchased appliance.
Tools
Cross-head screwdriver
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY
Adjusting the alignment in the cabinetry
Powered driver
(optional)
1
Front foot adjustment screw
Rear foot adjustment screw
Foot
Clockwise turn of the front and rear adjustment screws raise the height of the appliance.
Counter-clockwise turn of the adjustment screws lower the height of the appliance.
2
Front feet
Rear feet
Turn the front and rear adjustment screws clockwise to extend the front feet and rear feet until they engage the floor and the top bracket reaches the cabinetry ceiling.
3 Check the depth gauges while adjusting the screws to maintain alignment of the appliance.
Illustrations may differ from your purchased appliance.
39
Install fasteners kit
Securing the top brackets
SINGLE INSTALLATION — SECURE APPLIANCE INTO CABINETRY
8Gx16 Countersunk screw (6x)
Tools
Fix the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws.
Cross-head screwdriver
Powered driver
(optional)
Securing the side brackets
Fix the side brackets (2x) to the lower right and left sides of the cabinetry with 8Gx16 countersunk screws.
Once the appliance is secured to the cabinetry, remove the alignment gauges and re-tighten the side screws.
40 Illustrations may differ from your purchased appliance.
DOOR PANEL INSTALLATION
Tools
Cross-head screwdriver
M4 hex key (1x)
Hanging the door panel
1
13mm spanner (1x)
13mm socket wrench
Hold the door panel at an angle from the top of the door and lower the screw holes of the hanging bracket onto the adjustment screws. .
3
2
Align the door panel straight with the door and slide-in the side brackets to the side screws of the door,
Tighten the side screws loosely to temporarily secure the door panel.
Screw the M8 washer and nut to the adjustment screw and loosely tighten.
For Refrigerator-Freezer
Repeat steps 1 – 3 for the top door and drawer panels.
Use a 13mm socket wrench to tighten or loosen the M8 nut in the drawer panel.
Illustrations may differ from your purchased appliance.
41
Tools
Cross-head screwdriver
M4 hex key (1)
13mm spanner (1x)
DOOR PANEL INSTALLATION
Adjusting the width of the door panel Adjusting the height of door the panel
Ensure the side brackets are loosely screwed when adjusting the height of the door panel. Do not adjust the door panel height when the side brackets are screwed tight. This can generate friction which causes the hanging brackets to bend. z
Turn the adjustment screw to raise or lower the height of the door panel relative to the door.
Continue adjustment until gap with cabinetry is more than 3mm.
Do not adjust the adjustment screw higher than 1/4" (6.5mm) from its fully down position.
To adjust the door panel further, loosen the M8 washer and nut and slide the door panel to suit. If further adjustment is still required, remove the door panel then loosen the fixing screws of the hanging bracket and move bracket sideways to suit.
Adjust the depth of door panel
Loosen side screws on the side brackets, and slide door panel forward/backward.
Re-tighten once satisfied.
Once satisfied with door panel position, fully tighten M8 washer and nut to adjustment screw.
42 Illustrations may differ from your purchased appliance.
DOOR PANEL INSTALLATION
Installing locking bracket Tools
Cross-head screwdriver
Cutter
M4 hex key (1x)
13mm spanner (1x)
1
REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR—FREEZER
Loosen the screw at the bottom of the door, and slide the locking bracket out until it touches the panel.
Refrigerator-Freezer
The locking bracket is located at the bottom of the top door panel.
2
B
Fix the locking bracket to the door panel with 8Gx16 countersunk screw.
3 Re-tighten the screw at the bottom of the door.
TOE KICK INSTALLATION
Adjusting mounting plate brackets
1
2 cap screw adjustment brackets
Loosen the cap screws of the adjustment brackets on both sides of the plinth with a hex key.
Adjust the brackets to the desired depth by moving it forward/backward.
Re-tighten the cap screws once satisfied.
Illustrations may differ from your purchased appliance.
43
Miscellaneous components
Attaching the mounting plate
Air toe kick seal (1x)
Toe kick install kit
Toe kick panel (1x)
Magnets (4x)
8Gx16 Mush washer screws (4x)
Tools
1
Cross-head screwdriver
M4 hex key (1x) 2
Powered driver
44 Illustrations may differ from your purchased appliance.
TOE KICK INSTALLATION
Stainless steel toe kick
Purchased separately. Visit fisherpaykel.com for information.
Single installation
Custom toe kick
Suppplied by customer to match cabinetry.
Stainless steel panel
Custom panel
Dual installation
Re-attach the toe kick mounting plate to the plinth using same screws that were set aside previously.
If toe kick depth is less than 92mm, attach an air toe kick seal to the mounting plate.
Peel off the adhesive tape of air toe kick seal and attach to the middle of the back side of the mounting plate.
Press firmly to ensure the tape adheres to the mounting plate.
Triple installation
Stainless steel panel
Stainless steel panel
Custom panel
Custom panel
toe kick mounting plate
1
2
STAINLESS STEEL TOE KICK
TOE KICK INSTALLATION
magnet attachment area magnet fixing location toe kick mounting plate
1 spacers screws magnets
2
CUSTOM TOE KICK
magnet attachment area magnet fixing location screws magnets
3 3
45
GRILLES INSTALLATION
Tools
Cutter
Cross-head screwdriver
Attaching the top grille top grille
Refrigerator or Freezer/
Wine Cabinet
Open the door, and secure both ends of the grille and behind the water filter hatch with #8x16 screws.
Attaching the bottom grille
Refrigerator or Freezer/
Wine Cabinet
Re-attach the bottom grille via magnets. bottom grille
For toe kick heights 114–127mm, shorten the bottom grille by cutting along the vertical ribs.
46 Illustrations may differ from your purchased appliance.
top grille
Refrigerator-Freezer
Reattach the top grille with
#8x16 screws.
bottom grille
Refrigerator-Freezer
Re-attach the bottom grille via magnets.
CARBON FILTER INSTALLATION
The carbon filter is used for Wine Cabinet models only, Ensure the cover is completely closed to prevent hatch or filter from being damaged. Replacement filters (862755) can be purchased online from fisherpaykel.com or by calling Fisher & Paykel Customer Care.
AIR FLOW DIVIDER INSTALLATION
The air flow divider blocks the air flow from bypassing the front of the bottom grille.
1
Remove the packaging of the filter.
2
3
4
Push-open latch
Open the cover of filter housing by pushing the latch.
Housing
1
REFRIGERATOR & FREEZER / WINE CABINET REFRIGERATOR—FREEZER
Remove the adhesive layer off the air flow divider.
Insert the carbon filter in the hatch.
2
Press the flow divider firmly against the bottom of the door/drawer panel.
Ensure the adhesive layer side of the divider contacts the door panel.
Secure the air flow divider to the panel with screw.
Push the filter gently into the hatch until flush, and then close the cover until it locks to the latch.
3 Attach a flow divider cap to the flow divider.
Illustrations may differ from your purchased appliance.
47
Trims install kit
Top door panel side extrusion (2x)
Bottom drawer panel side extrusion (2x)
DOOR COVERS & TRIMS INSTALLATION
Re-installing the top cover (for all models)
Remove the backing film of dual adhesive strips pre-attached to the top of the door. Ensure the magnet is in place before installing the top cover.
trim cap top cover notch
1 magnet housing trim cap
Align the top cover to the top of the door.
Clip the notch into the magnet housing, and the trim caps on top of the adhesive strips.
2
Press down both ends of the top cover to engage the trim caps on the adhesive strips.
Ensure the magnet remains in place and not damaged as this will affect the operation of the appliance.
Bottom drawer top trim (1x)
Installing the door side covers
Refrigerator, freezer and wine cabinet Refrigerator-freezer
1
Insert door side covers into the gaps on the right and left sides of the drawer and slide downwards to clip into place. Press firmly to secure.
1
Insert the drawer side covers into the panel gaps on the right and left sides of the drawer.
Ensure the cabinet is centered to prevent the side covers from interfering with the cabinet.
2
Align top trim to drawer and press down firmly to secure within panel bracket clips.
2 Ensure side cover is aligned with the top door panel extrusion.
3 Ensure top trim is aligned with the drawer side covers.
48 Illustrations may differ from your purchased appliance.
2
3
TOP TRIM & HINGE POCKET COVERS INSTALLATION
installing the top trim (for all models) top trim installing the hinge pocket covers (for all models)
Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
1
Slide one end of the top trim into the hinge pocket of the appliance.
Press the other end to engage the dual lock strips on the non-hinge side of the appliance.
Place the hinge pocket cover to the hinge pocket, matching the studs on the cover to the slots in the hinge pocket.
Slide the cover inside the pocket.
Press the pocket cover to ensure the cover clips into the pocket.
Your Integrated Installation is now complete!
Illustrations may differ from your purchased appliance.
49
Install fasteners kit
MULTIPLE INSTALLATION — APPLIANCE PREPARATION
Attach barbed plugs and depth alignment gauges Add flange joiner
Barbed plugs (2)
Cabinet depth alignment gauges
(4)
1 barbed plugs depth gauges locations
Insert the barbed plugs into large holes on the top right and left sides of both appliances.
The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance.
Flange joiners (2)
Tools
2
Loosen the right and left screws at the top and bottom sides of the door.
Locate the alignment gauges at correct orientation to the right and left screws.
Remove alcove trims
Cross-head screwdriver
Powered driver
(optional)
3mm Allen key
3
Left Right z
Place the alignment gauge by inserting the screw head through the keyhole of the gauge.
Push the alignment gauge down to lock the position.
Tighten the screw just enough to firmly hold the gauge.
The alignment gauges are only temporary and must be removed after installation.
50 Illustrations may differ from your purchased appliance.
Remove bolts from the locations marked via the green labels on your appliance. Add the flange joiners, and tighten using a 3mm
Allen key to secure.
Remove alcove trims between adjacent products.
Joiner fastener kit Fit lower joiner bracket
Joiner Sleeve (2)
Bolt M5 HEX (2)
M6 Hex Nut (1)
1
Screw WSH M6 (1)
2
MULTIPLE INSTALLATION — JOIN PRODUCTS
Fit upper joiner bracket
Carefully roll both products halfway into cabinetry.
Take note of the upper and lower joiner locations illustrated.
1
2
Clamp the lower brackets together using the supplied M6 screw and
Nut. Secure using a 4mm Allen key and 10mm spanner.
Ensure brackets are clamped tightly before proceeding.
3
Clamp the upper brackets together by fitting the first the supplied
M5 bolt and joiner sleeve. Tighten using a 8mm socket and Phillips screwdriver until the sleeve sits flush.
Handle to handle installations:
Fit the second supplied M5 bolt and joiner sleeve.
For handle to handle install, use two bolts from both sides.
For handle to hinge, only one joiner bolt from handle side be inserted.
Ensure the flange joiners contact the adjacent product as shown.
Illustrations may differ from your purchased appliance.
51
Tools
Ruler
MULTIPLE INSTALLATION — ROLL INTO CABINETRY
Pushing into the cabinetry and aligning the depth gauges adjacent cabinetry depth gauge
1 Carefully roll both products into cabinetry.
2 Mark the step of depth gauge on the cabinetry sides of the doors based on the thickness of door panel.
Align the marked line flush with the front surface of the adjacent cabinetry.
52 Illustrations may differ from your purchased appliance.
Install fasteners kit
MULTIPLE INSTALLATION — LEVEL AND SECURE
Adjusting alignment of appliance in cabinetry Securing the top brackets
8Gx16 Countersunk screw (6)
Tools
1
Front foot adjustment screw
Rear foot adjustment screw
Foot
Turn the front and rear adjustment screws clockwise to raise height of the appliances and counter-clockwise to lower the height.
Left top bracket
Cross-head screwdriver
Powered driver
(optional)
Ruler
2 Rear foot
1
Beginning with the outside feet, turn the right hand screw to adjust the rear of the product followed by the lefthand screw to adjust the front. Once product is set in cavity, adjust the central feet.
Ensure feet engage with the floor and the upper bracket touches the alcove.
Securing the side brackets
2
Front foot
Right top bracket
Left lower side bracket ruler
Fix the left and right top brackets to the ceiling surface of the cabinetry with
8Gx16 countersunk screws.
Fix one lower side bracket to the cabinetry side surface with 8Gx16 countersunk screws.
3
Check the alignment gauges while adjusting the screws to maintain the alignment of the appliance.
Using a ruler, check if the gaps between appliance and cabinetry side wall are even.
Illustrations may differ from your purchased appliance.
53
Tools
Cutter
Cross-head screwdriver
Attaching the top grille
GRILLES INSTALLATION
Refrigerator or Freezer/
Wine Cabinet
Open the door, and secure both ends of the grille and behind the water filter hatch with #8x16 screws.
Attaching the bottom grille
Refrigerator or Freezer/
Wine Cabinet
Re-attach the bottom grille via magnets. bottom grille
For toe kick heights 114–127mm, shorten the bottom grille by cutting along the vertical ribs.
54 Illustrations may differ from your purchased appliance.
Refrigerator-Freezer
Reattach the top grille with #8x16 screws.
Refrigerator-Freezer
Re-attach the bottom grille via magnets.
bottom grille
2
3 installing the top trim (for all models)
MULTIPLE INSTALLATION — TOP TRIM & HINGE POCKET COVERS INSTALLATION
top trim
Slide one end of the top trim into the hinge pocket of the appliance.
Press the other end to engage the dual lock strips on the non-hinge side of the appliance.
installing the hinge pocket covers (for all models)
Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
1
Place the hinge pocket cover to the hinge pocket, matching the studs on the cover to the slots in the hinge pocket.
Slide the cover inside the pocket.
Press the pocket cover to ensure the cover clips into the pocket.
Your Integrated Installation is now complete!
Illustrations may differ from your purchased appliance.
55
Tools
Aluminium centre trim (1x)
Install the centre trim
1
MULTIPLE INSTALLATION — INSTALL TRIMS
Position centre trim between products.
3 Push trim into the lower bracket.
2 Push trim up into the upper bracket.
4 centre trim
Press the centre trim to fix the position.
56
WINE DISPLAY FOR WINE CABINET
Handle assembly
Retainer blocks are pre-assembled at the bottom of both ends of the handle.
Cradle assembly
A retainer block is pre-assembled at the bottom of each cradle. Use a spacer to correctly position the cradle and avoid wine bottles being too upright resulting in bottles tipping over.
1
Loosen the screws until the retainer blocks can be inserted between slats of display rack.
1
Insert retainer block at desired location between slats of display rack. Do not tighten.
2
3
Align handle to the front end of display rack.
Rotate retainer block to lock position and tighten screw to lock handle in place.
2
3
Place ‘cradle guide’ on the slats behind the handle..
Align cradle on spacer based on size and type of wine bottle.
Rotate the retainer block to lock position, and tighten screw.
Remove cradle guide from the rack after use.
Wine label kit
1 Write the name or type of wine on the label.
3 Wipe the labels with a damp cloth to erase.
2 Fit label over front edge of rack to match displayed wine.
57
CHANGE THE DOOR HINGES (OPTIONAL)
You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door.
Detach the door
1
REFRIGERATOR & FREEZER / WINE CABINET REFRIGERATOR—FREEZER
‘0’
Release the hinge spring by turning the
T20 screw in the hinge to the ‘0’ position.
Close the door and lay the appliance on its back on the pallet.
2
REFRIGERATOR & FREEZER / WINE CABINET REFRIGERATOR—FREEZER
M6x10 hex screws
Top hinge bottom/middle hinge
Detach the door from the appliance by unscrewing the door hinge M6x10 hex screws (4x) at the top hinge and bottom/ middle hinge.
T20 screw
58
Detach the top door hinge f
D b
A
CHANGE THE DOOR HINGES (OPTIONAL)
C
E
1 Rotate the top hinge ( A ) outwards and remove the top hinge pocket cover ( B ) using the flat head screwdriver in the slot of the cover.
2 Unscrew M6x16 countersunk screws ( C ) to remove top hinge, and set aside to use later.
3 Unscrew M6x16 countersunk screws ( D ) from hinge pocket to remove hinge pocket and top alcove bracket.
4 E ) to remove top hinge bracket and spacer.
For the non-hinge side, remove the top alcove bracket by unscrewing the M6x16 countersunk screws ( F ).
Detach the bottom door hinge — For Refrigerator & Freezer / Wine Cabinet a
E
Do not remove!
B d
C
E
F
1 Rotate the bottom hinge ( A ) outwards and remove bottom hinge pocket cover ( B ) using a flat head screwdriver in the slot.
2 Remove the hinge by unscrewing the
M6x16 countersunk screws (2x) ( C ).
3 Open the water filter hatch on the bottom grille and unscrew the
#8x16 screw ( D ) while holding the grille in place.
4 unscrewing the #8x16 screws ( E ) from the bottom left and right of the grille.
5 Remove bottom hinge bracket by unscrewing M6x16 countersunk screws ( F ).
IMPORTANT!
Do not remove plinth-to-cabinet retention brackets!
Detach the middle door hinge — For Refrigerator-Freezer
A
B
C 1 Rotate the middle hinge ( A ) and unscrew M6x16 countersunk screws ( B ) to remove middle hinge, and set aside to use later.
2 screws ( C ) to remove top hinge bracket and spacer.
59
Move the sensor housing
CHANGE THE DOOR HINGES (OPTIONAL)
1
2
3
Unclip the hall sensor from the housing.
4
Unhook the interceptor board harness from sensor housing so harness is loose.
Remove the #8x16 screws (2x) from the sensor housing.
Move the sensor housing to align the opposite hall sensor clip with the centre of the cabinet.
5
6
Reinstall the sensor housing using #8x16 screws (2x) into the pre-drilled holes in the cabinet top panel.
F
Clip the hall sensor into the sensor housing in the pocket closest to the centreline of the cabinet.
7
Press the harness from the interceptor board into the forks on the sensor housing.
Re-attach the top door hinge c
A
CHANGE THE DOOR HINGES (OPTIONAL)
D e b f
1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws ( A ) on the new hinge side at the other side of the appliance.
Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M6x16 countersunk screws ( B ).
z
The new hinge pocket and top alcove bracket are supplied with the hinge kit.
Install the new hinge in the new hinge pocket by screwing M6x16 countersunk screws (2x) ( C ).
4 D ) and clip the top hinge pocket cover ( E ) to the top hinge pocket.
5 non-hinge side ( F ).
Re-attach the bottom door hinge — Refrigerator or Freezer / Wine Cabinet
C
A
B
D
E d
D
1 Install a new lower hinge bracket on the new hinge side with M6x16 screws (2x) ( A ).
2 Ensure that the tab on the top of the bracket inserts into the slot in the plinth front bracket.
3 Use the hinge that was removed from the top of the appliance and insert the tabs into the hinge lower bracket.
Rotate the hinge into place and fix with
M5x12 countersunk screws (2x) ( B ).
4 C top grille assembly.
), and install the new
5
( D ).
One each at the bottom left and right of the grille and one behind the water filter hatch.
6 the new hinge pocket ( E ).
Re-attach the middle door hinge — wRefrigerator-Freezer
B
C
A
1 Reinstall the middle hinge bracket and spacer with M5x12 countersunk screws ( A ).
2 Open the middle hinge ( B ) and reinstall the hinge with M6x16 countersunk screws ( C ).
61
Change the top door brackets
A b
CHANGE THE DOOR HINGES (OPTIONAL)
Reinstall the door
1 Unscrew the M5x10 screws (4x) to remove the top adapter bracket from the top of the door ( A ).
2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) ( B ).
M6x10 hex screws
Top hinge
1 Secure the door to the top hinge and bottom/middle hinge with M6x10 hex screws (4x).
use new top adaptor bracket
Bottom/middle hinge
Change the bottom door bracket c use new bottom adaptor bracket and spacer d e f use existing locking bracket
62
1 Remove the door panel locking bracket and washer from the bottom of the door by unscrewing M6x25 screw (1x) ( C ).
and spacer from the bottom of the door by unscrewing M6x25 screws (2x) and M5x30 screw (1x) ( D ).
and existing spacer to the other side of the door with M6x25 screws (2x) and
M5x30 screw (1x) ( E ).
bracket and washer to the other side of the door with M6x25 screw (1x) ( F ).
T20 screw
‘I’
2 Activate the hinge spring by turning the star T20 screws to the I position.
3 Return the appliance to the upright position, and reinstall all covers and trims.
FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
All models
Cabinet Level: Ensure the appliance is level and dimensions accurate.
Refer to 'Cabinetry Dimensions', pages 14–15.
Anti-tip: Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Refer to 'Cavity preparation', page 30.
Door panel/and toe kick: Ensure door panel/s and toe kick are attached securely and properly aligned; Refer to 'Door panel installation', pages 41–43, and 'Toe kick installation', pages 43-45.
Doors closing freely: Ensure the door/drawer can open and close freely with no resistance from surrounding cabinetry or product. Refer to 'Door clearance' and
'Drawer clearance', page 21.
Hinge pin: Ensure hinge limiting pin is fitted for 90° door swing. Refer to
'Door clearance', page 21.
Vent clearance: Ensure the cabinet installation provides the minimum vent clearance required. Check that the gap between the bottom of the door panel and the ground is at least 50mm. Refer to 'Product Dimensions', page 13.
Installation trims: Check all Installation Trims are present and fitted securely.
Door opening sensor: Ensure magnets and sensors are correctly installed by checking that the door alarm is not beeping and that compartment lights are on when door is opened.
Packaging: Ensure all internal and external packaging has been removed. Refer to
'Before installation', page 28.
Fault codes: Ensure no error codes are shown.
Installation mode: Ensure the Installation Mode is de-activated (hold on Compartment
button for 4 sec. Refer to 'Power and water supply connection', page 37.
User guide: Check the User Guide is inside the product in a visible area for the customer.
For products with water only or Ice and water function
Ice maker: Turn ice maker ON. Force a manual ice maker cycle by pressing the (alarm symbol), - & + buttons together for 4 seconds then close the door(s). The ice tray will fill and empty into the bin below, dry the bin and return it correctly. Refer to page 19 of your User Guide.
Dispenser: Ensure the water is flowing through the system using the dispenser pad.
Refer to page 18 of your User Guide.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
63
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2022. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.
866170B 04.22
Stáhnout
Veřejný odkaz aktualizován
Veřejný odkaz na váš chat byl aktualizován. You may view and manage your chat links after registration here.
Veřejný odkaz na dokument
Reklama