Dataplex DPX-213 User manual

PDF

เอกสาร

โฆษณา

DPX-213

LOW POWER DATA MODEM

USER MANUAL

2400/1200/300bps MNP-5 Data

Leased Line & Dial Network Modem

WARNING

When operating the DPX213 from a DC supply ensure that any devices that are connected to the DPX213 have a common NEGATIVE ground or are powered from an isolated source. It is recommended that the supply be connected via a disconnection device or an over-current protection device.

SAFETY

The 48V free standing unit is fitted with a 2m power supply cable with bare wire ends. This power supply cable must be connected to the power source via a disconnection device or an over-current protection device. A circuit breaker rated

1A, 100 VDC will satisfy both requirements. Observe correct polarity:

• Red wire to positive;

• Black wire to negative.

COPYRIGHT

This manual cannot be reproduced in any form without the prior written consent of Dataplex Pty. Ltd. No patent liability is assumed with respect to the use of the information contained in this manual.

TRADEMARKS

DPX-213 is a trademark of Dataplex Pty. Ltd.

DATAPLEX is a trademark of Dataplex Pty. Ltd.

II Document No 113-213-01 Rev 1.0

1.0 INTRODUCTION

1.1 Features of the DPX-213

1.2 Requirements

1.3 About the Manual

1.4 The DPX-213 Modem

2.0 INSTALLATION

2.1 Setting the Internal Jumpers

2.2 Connecting the DPX-213 to the Telephone Line

2.3 Connecting a Terminal or Computer to the DPX-213

2.4 Front Panel Indicators

2.5 Testing Your Connections

2.6 Setting Your PC for Speed and Character Format

2.7 Making a Connection

2.8 Closing a Connection

2.9 Call Establishment Sequence

2.10 Trouble Shooting

3.0 BEFORE YOU START

3.1 Command Structure

3.2 Communications Software

3.3 Manual and Automatic Calling

3.4 Dial-up Line and Leased Line Support

3.5 Speed Matching

3.6 Flow Control

3.7 Escape Sequence

3.8 Advanced Features

4.0 COMMAND SET

4.1 Command Line and Command Entry

4.2 Attention Code Syntax

4.3 DPX-213 Operating States

4.4 AT Command Set

1-1

1-1

1-2

1-3

2-3

2-1

2-1

2-2

2-3

2-4

2-5

2-6

2-7

3-1

3-1

3-2

3-3

4-2

4-1

4-1

4-3

4-6

Document No 113-213-01 Rev 1.0 2008 III

5.0 APPLICATIONS

5.1 Resetting the Modem

5.2 Operating Modes

5.3 Asynchronous Modes

5.4 Synchronous Modes

5.5 Leased Line Operation

5.6 Extended Character Formats

5.7 PABX Operating Problems

5.8 Low Power/Standby Mode

5.9 Alarm Mode

5.10 Password Mode

5.11 Remote Configuration

6.0 DATA TRANSFER

6.1 Error Control

6.2 Flow Control

6.3 Flow Control Buffers

6.4 Microcom Networking Protocol

6.5 Error Free or Not At All

6.6 Constant Speed Interface

6.7 File Transfer Restrictions

6.8 Software Compatibility

7.0 TESTING AND DIAGNOSTICS

7.1 Operator Initiated Tests

7.2 Local Analog Loopback (ALB)

7.3 Remote Loopback Response

7.4 Remote Digital Loopback (RDLB)

8.0 S-REGISTERS

9.0 TECHNICAL SPECIFICATIONS

Models Available

10.0 WARRANTY AND REPAIRS

Warranty Information

Installation and Service Record

8-1

9-1

10-1

6-1

6-1

6-2

6-4

6-5

6-6

5-1

5-1

5-2

5-3

5-4

5-5

5-6

5-7

7-1

7-1

7-2

7-3

Document No 113-213-01 Rev 1.0 2008 IV

APPENDICES

Appendix A

Appendix B

Appendix C

Appendix D

Appendix E

Problem Report Sheet

S Register Summary

ASCII Conversion Table

Interface Connections

AT Command Set Summary

FIGURES

Figure 2.1

Figure 2.2

Figure 2.3

Figure 5.1

Figure 6.1

Figure 7.1

Figure 7.2

Figure D.1

TABLES

Table 2.1

Table 2.2

Table 4.1

Table 4.2

Table 5.1

Table 5.2

Table 5.3

Table 8.1

Table D.1

Rear Panel Layout

DPX-213 Jumper Locations

Front Panel Layout

Telecom 604 Plug

Flow Control Buffers

Local Analog Loopback

Remote Digital Loopback

RJ-11 Connector Wiring

Front Panel Indicator Names and Functions

Valid Character Formats

CCITT and Bell Selection

Response Codes

Mode 0 Asynchronous

Mode 1 Asynchronous

Mode 2 Synchronous

Table for Converting 8 Bit Binary to Decimal

V.24 Interface Connectors

2-1

2-2

2-3

5-5

6-2

7-2

7-3

D-1

2-3

2-4

4-7

4-14

5-2

5-3

8-1

D-2

Document No 113-213-01 Rev 1.0 2008 V

T HIS PAGE INTENTIONALLY LEFT BLANK .

VI Document No 113-213-01 Rev 1.0

INTRODUCTION Section 1

1.0 INTRODUCTION

Welcome to the Dataplex DPX-213. Whether you are familiar with dial network modems or not, you will find the DPX-213 simple to operate. The modem offers advanced features only found in quality high-end products and opens the door to a new world of data communications. Congratulations on your purchase of the DPX-213.

1.1 Features of the DPX-213

This low power dial network and leased line data modem is designed for advanced business and professional applications. A wide range of useful features allow many different types of networks to be configured with the one compact unit. MNP 4 error correction and MNP 5 data compression permit error free transmission of data at up to four times the throughput of basic 2400 bps modems.

The DPX-213 supports five international speed standards for both synchronous and asynchronous communications.

1.2 Requirements

To operate the DPX-213, it is assumed that the user is reasonably familiar with data communications concepts and personal computers. If you are unfamiliar with data communications or personal computers, please refer to the relevant texts or user manuals.

Before you can operate the modem, ensure you have the following equipment:

1. An asynchronous terminal. This can be a personal computer with an RS-232

serial port or a dumb asynchronous terminal. Once configured, synchronous

devices may be used.

2. Data communications software.

3. A DTE (Data Terminating Equipment) cable.

Copyright (C) Dataplex Pty Ltd 1-1

INTRODUCTION

1.3 About the Manual

Section 1

The manual is organised to explain increasingly more advanced operations. Novice users should read all sections, in particular, Section 3 on modem basics and Section 7 on

Applications. The manual is divided into 12 sections as follows:

Section 1 Introduction describes the DPX-213 features and explains how to use this manual.

Section 2 Installation explains the purpose of each indicator, switch and connector plus how to connect your modem to the computer and telephone line.

Section 3 Before You Start covers the command method, dialling, answering, matching dissimilar speeds, leased line and dial network operation.

Section 4 Command Set is probably the most important Section. It explains in detail the function of each AT command for both fax and normal modem operation.

Section 5 Applications offers some quick start information on a range of common uses including password security, synchronous support, leased line operation, extended character set support and remote configuration.

Section 6 Data Transfer describes advanced features such as error correction, data compression, flow control and speed matching. This Section also gives some warnings on set-up conflicts to be avoided.

Section 7 Testing and Diagnostics covers the loopbacks and test patterns available to help isolate any problem in your cable, modem or phone line.

Section 8 S-Registers covers the software registers used to store the DPX-213 configuration options. Instructions are given to enable reading and altering the S-Register values.

Section 9 Technical Specifications gives the performance specifications of the DPX-

213 and lists the other models available.

Section 10 Warranty and Repair allows you to record the installation configuration.

Also included is warranty information and a field service request form.

Appendices The appendices contain a problem report sheet, interface signal leads/connections information, an ASCII code table (in decimal, binary and hex), an S-registers summary table and the AT Command Set Summary.

1-2 Copyright (C) Dataplex Pty Ltd

Section 1 INTRODUCTION

1.4 The DPX-213 Modem

The DPX-213 is designed and built in Australia and offers:

• Low Power: Standby current < 100uA.

Operating current < 100mA

•

Wake up on DTE RxD, Ring or Raise of

DTR.

• Led operation link selectable.

• DTR wake-up link selectable.

• Alarm/Dialback function.

• Password security/dialback.

• Remote configuration.

• Async/Sync link selectable.

• Power from DB25, IDC or Power

Connector.

• Small size.

• MNP error correction & data compression.

• Constant speed interface from 300 to 9,600 bps.

• Automatic terminal speed detection from

300 to 9,600 bps.

•

Data operation at 300, 1200, and 2400 bps.

Auto-ranging on originate and answer at

300, 1200 and 2400 bps.

• CCITT standards V.21, V.22, and V.22bis.

• Bell 103 and Bell 212 support.

• A rugged plastic case.

• Front panel indicators.

• Stored number dialling for up to ten numbers.

• DTR raise and AT command dialling.

• Help screens for configuration, S-registers and AT prompts.

• Manufactured to ISO-9002/AS-3902 quality standards.

• Austel approved.

• RFI compliant to AS-3458 and CISPR-22 class A.

1-3

INTRODUCTION

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 1

1-4 Copyright (C) Dataplex Pty Ltd

INSTALLATION Section 2

2.0 INSTALLATION

Read this Section in order to correctly install your modem. It includes information on connector pinouts, front and rear panel details and a simple test of your setup.

Before operation is possible, the modem must be setup, either to the factory defaults or with special S-register values to suit your own configuration.

Most communications software packages issue a default command string to set up the modem. Before altering this default setup, check the software operations manual and

Section 4, Command Set.

Figure 2.1 Rear Panel Layout

The rear panel of the DPX-213 has a single RJ-11 connector for line, together with a 25

Pin V.24/28 DCE connector. The supplied line cord connects from the RJ-11 of the DPX-

213 to the telephone wall socket. A description of the RJ-11 connectors is given in

Appendix D.

2.1 Setting the Internal Jumpers

The DPX-213 contains a number of internal jumpers which have to be set before operation. The figure over page shows the location of the various jumpers.

Copyright (C) Dataplex Pty Ltd 2-1

INSTALLATION Section 2

RESET

Figure 2.2 DPX-213 Jumper Locations

J4: Removing this jumper reduces current consumption by disabling the front panel

LEDs.

J5: Removing this jumper stops the V.24 DTR input which controls the standby mode of the DPX-213. Without this jumper set, the unit will not wake up on raise of DTR and will not be held active by the DTR when the unit is placed in standby mode.

J8: This jumper enables the sync clocks on the V24 interface. When Pins 1 and 2 are shorted no sync clocks will be present at the interface. When Pins 2 and 3 are selected, both Rx and Tx sync clocks will be placed on Pins 17 and 15 of the DB25 connector.

2.2 Connecting the DPX-213 to the Telephone Line

Remove your telephone from its wall socket (you may need a flat bladed screwdriver for this) and plug one end of the supplied cable into the socket labelled "J2 LINE" on the rear of the DPX-213 and plug the other end into the wall socket. The terminal prompts will give call progress indication.

NOTE: 1. Dataplex does NOT recommend the use of double adaptors to connect your telephone in parallel with the DPX-213. Should the handset be lifted when the modem is online, noise and errors will be injected into the data stream.

2. If the handset draws power from the telephone line (for example, to keep stored numbers intact or to run a clock display) the battery charging current can be a source of noise and errors in the data during long modem sessions. A long data call may cause the telephone memory battery to discharge and lose the stored numbers.

2-2 Copyright (C) Dataplex Pty Ltd

Section 2

2.3 Connecting a Terminal or Computer to the DPX-213

INSTALLATION

The DPX-213 uses the industry standard 25 Pin "D" connector as its data interface, with the signals defined in the CCITT V.24, V.28 and EIA RS-232C for modems. The DPX-

213 operates as Data Circuit-terminating Equipment (DCE).

If you wish to connect the DPX-213 to a terminal or computer with a serial port configured as Data Terminal Equipment (DTE), then a "straight through" cable connecting corresponding pins of the serial ports should work. If the computer serial port is configured as a DCE, then you must use a "cross over" or "null modem" cable. Most personal computers and terminals have their serial interface configured for DTE operation. The connections needed for dumb terminals, PC's and asynchronous operation are described in

Appendix D.

NOTE: When connecting the RS-232 cable to the PC, DO NOT connect the cable to the

DB25 female connector on the rear of the PC. This is the parallel port and connection may cause damage to your PC. At the PC end, the cable should be connected to a male connector (serial port) for correct operation.

The terminal cable to the modem should be less than 15 meters in length and restrained with screw locks at both ends to avoid placing too much strain on the cable. Round cable is recommended. Ribbon cables MUST be kept as short as possible to minimise clock and data interference in the ribbon.

2.4 Front Panel Indicators

The front panel of the DPX-213 contains 4 LED's (Light Emitting Diodes), which are used to indicate modem and line status.

Figure 2.3 Front Panel Layout

2-3

INSTALLATION

Table 2.1

Name Function

Transmit Data

Receive Data

Carrier Detect

Off Hook

Front Panel Indicator Names and Functions.

Colour Status

Yellow Off for mark, On for space, flickering for data

Green On when CD active, Off when CD inactive.

(See AT&C command)

Red On when modem is on line (Off hook). Off when modem is off line (On-hook).

When the modem is in Loop modes this LED flashes.

Section 2

2.5 Testing Your Connections

With your terminal or computer connected and operating, the DTR LED should light. You can now perform a quick test to determine if you have setup the DPX-213 correctly.

After connecting your terminal or PC to the modem, power the system up and start your communications or terminal emulation package. To check that keyboard characters are reaching the DPX-213, the TD LED must flash with every keystroke.

Press the

K

key. Each time you press the key, the TD LED should flash briefly. If no data is reaching the DPX-213, check that:

1. The correct COM port is being used on your PC;

2. The terminal is in the ON-LINE state and not the LOCAL Mode state, or,

3. The correct cable is being used and the cable pinouts are correct.

2.6 Setting Your PC for Speed and Character Format

2-4

The DPX-213 uses the attention request ('AT' prefix) to automatically detect terminal speeds at all standard baud rates up to 9,600 baud.

For initial configuration, the terminal used must be a ten bit ASCII device operating at one of the standard speeds, for example, 300, 1200, 2400, 4800, 9600 or 19,200 bps. The AT command processor and Constant Speed Interface accept character formats of 10 bits in total.

For example:

Section 2 INSTALLATION

Table 2.2 Valid Character Formats

Start Bit

Data Bits Parity

Mark

Even

Odd

Space

None

Stop Bits

Total Bits

2.7 Making a Connection

Make sure the cable and terminal software are correct, then type

atK

. This allows the modem to sense the terminal speed and calculate the parity being used. After this has been successfully decoded, the DPX-213 will reply with:

"OK"

NOTE: If the modem fails to issue the "OK" response, and you are certain the cable, terminal speed and parity are all correct, refer to the Section on Testing and

Diagnostics.

The DPX-213 comes with a default configuration suitable for many applications. As a

"soft" configured product, it is possible to make errors by loading a conflicting configuration, causing unpredictable operation. If you suspect this has happened, turn the power off, wait about ten seconds, and then turn the power back on. Force the modem back to the factory default setup by typing

at&fK

Otherwise, type

ath1K

to force the modem to go Off Hook (equivalent to lifting the handset). Typing the command line

athK

ath0K

will terminate the call.

Dial a number by typing the command line:

atd 1234567K

(Fictitious Number Only)

The above command tells the modem to dial (ATD) the number 1234567. Where nonstandard dial tones are used, such as with some PABX's, the modem may not be able to detect dial tone. In this case select the appropriate pulse or tone dialling method with the

ATDP or ATDT commands respectively and ensure the modem "blind dials" by using the

ATX0 or the ATX2 command.

When dialling a number, you should see various prompts on your terminal.

Copyright (C) Dataplex Pty Ltd 2-5

INSTALLATION

2.8 Closing a Connection

Section 2

There are several ways to abort a call. If the call has been answered by a modem and both are on-line, typing any key will now send that character to the attached modem. Aborting the call in this case must be done from the on-line interactive state which is entered by typing the escape sequence of 'pause'

+++

'pause' followed by

athK

The abort timer (S-Register 7) will also abort the call if the originating modem has not established a call before S7 times out. This is normally 45 seconds but can be between 1 and 255 seconds.

Basically, a call can be terminated in several ways :

• Hitting any key on the terminal;

• Detection of busy tone by the DPX-213;

• Time-out of the modem (S-Register 7);

• Loss of carrier;

• Typing the escape sequence ('pause'

+++

'pause') then

ath0K

Additionally, a call will be terminated when either Busy tone (engaged) is detected or loss of power is applied to the modem by switching off or removing the power cord.

NOTE: If data is present, then one of the Dumb modes should be used (AT*D2).

2.9 Call Establishment Sequence

The modem placing the call is termed the originating modem and the modem at the other end is termed the answering modem. When instructed to place a call, the originating modem will go off-hook and the OH LED will illuminate. Typically, the originating modem listens briefly for dial tone before dialling, places the call, and then listens for answer tone from the answering modem. If no tone is received within a preset time (stored in S-Register 7), the call is aborted.

The originating modem is usually silent during this initial call set-up phase, but a calling tone can be enabled (via the AT*G command) which transmits an interrupted tone so the called party can distinguish a data call from a voice call and activate the modem if required.

At the answering end, the modem detects the incoming ring, counts up to the preset number of rings (stored in S-Register 0) and then goes off-hook. It transmits an answer tone to the calling modem. Once this tone is detected by the calling modem the training sequences begins. Therefore, it usually takes a few seconds before data transfer actually begins.

2-6 Copyright (C) Dataplex Pty Ltd

Section 2 INSTALLATION

The called modem will turn on the ring indicator with each incoming ring (Pin 22). It will usually output the word "RING" to the terminal with each incoming ring unless this feature has been disabled with the ATQ or ATV commands.

The DPX-213 can be configured so it will:

• Answer at a particular ring count (typically, the answering modem will be set to answer on the first or second ring;

• Never answer;

• Answer if the data terminal ready lead (Pin 20) is asserted.

2.10 Trouble Shooting

If you are sure you have the correct cables, terminal speed and ASCII character format, but are unable to get the OK response from typing AT, the DPX-213 may have an invalid setup string stored in the NVRAM.

A Master Reset should eliminate this problem. A Master Reset will erase all stored numbers, passwords and configuration information. To initiate the Master Reset, turn the

DPX-213 power off, remove the lid and short the reset pads on the PCB while turning the power back on. Wait a few seconds before removing the short

Now type

atK

as before. If you still experience problems, consult Section 7 on

Testing and Diagnostics or call your modem supplier for assistance. Details of the

Warranty and Service contacts are given in Section 10.

Copyright (C) Dataplex Pty Ltd 2-7

INSTALLATION

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 2

2-8 Copyright (C) Dataplex Pty Ltd

BEFORE YOU START Section 3

3.0 BEFORE YOU START

The DPX-213 is a combined soft-strapped and link selectable modem. There are number of internal links which can be used to select Async/Sync operation, DTR wakeup and LED operation. All other parameters are set by software commands from an attached asynchronous terminal and then stored in Non Volatile Random Access Memory

(NVRAM). These setups or configurations are stored in 'S-registers'.

3.1 Command Structure

In general, commands entered into the modem are prefixed with 'AT' and end with a carriage return (

K

The modem automatically determines the terminal speed and parity from the AT characters, loads the command into a buffer as you type it, and executes the command when you hit the carriage return.

The factory defaults assume you are going to use the modem for asynchronous operation on the dial network at the fastest speed the line or modem can accommodate. The character format is assumed to be 10 bit ASCII, consisting of 1 start bit, 8 data bits and 1 or more stop bits. For 8 to 11 bit configurations, read Section 5 on Applications and Section 8 on S-

Registers.

3.2 Communications Software

The software used to configure the DPX-213 can range from simple dumb terminal emulators to advanced communications systems. The DPX-213 is compatible with virtually all communications software packages. If using a smart communications package, ensure it supports the AT command set. Most packages also send an initialisation string.

This should be checked for correctness before using the modem.

3.3 Manual and Automatic Calling

Calls can be initiated by raising DTR from the terminal and typing an AT command string.

Calls can be answered by the same methods.

Copyright (C) Dataplex Pty Ltd 3-1

BEFORE YOU START

3.4 Dial-up Line and Leased Line Support

Section 3

The DPX-213 cannot share the same line as your normal telephone. It can only be used in isolation.

NOTE: Telephones with Mode 3 connectors should not be used with this equipment.

Contact Telecom if you are trying to use the modem on a small business key system such as a Commander, as these hand sets often signal to the PABX electronics with non standard tones and voltages. Damage to either the PABX or the modem could result from incorrect connection. A direct line from the local exchange may be needed in these situations.

Leased lines are special services providing a dedicated link between two sites. No switching is involved and hand sets are rarely provided. The DPX-213 can be configured to operate on two wire leased lines in synchronous or asynchronous modes. Special care has been taken with the design to ensure reliable operation in leased line mode, particularly with line changes caused by circuit re-routing. Section 5, Applications, details the recommended set-up strings for this use. Leased line also requires modifications to the line connector as shown in Appendix D.

3.5 Speed Matching

There are several forms of speed matching used in the DPX-213. The autobaud feature automatically senses the terminal speed from the typed AT commands and sets the modem interface speed to match the terminal. The autoranging feature automatically senses the line speed of the remote modem and adjusts to it in both originate and answer modes.

Additionally, there is a Constant Speed Interface (CSI) on the DPX-213 modem which allows your terminal to remain at the same speed, say 9,600 bps, for all 300, 1200 or 2400 bps full duplex calls. This simplifies operation with mini-computer systems provided you support flow control and avoids data loss if there is a speed mismatch in the system.

3.6 Flow Control

3-2

Flow control is needed whenever one device in the system runs faster or slower than another, or there are delays in transmission while errors are corrected. Flow control can be

In-band using Xon and Xoff characters or Out-of-band using Request To Send (RTS) and

Clear To Send (CTS). These are also referred to as software handshaking or hardware handshaking. It is legitimate to have different flow control techniques at each end of the link. The Xon and Xoff characters are user programmable in the DPX-213 and are stored in S-Registers 32 and 33 respectively.

Section 3

3.7 Escape Sequence

BEFORE YOU START

While off-line, the DPX-213 is in the Command State and all characters typed at your keyboard are scanned by the command interpreter awaiting AT commands. Once on-line, whatever is typed is sent to the remote modem. In order to get back in touch with the local command interpreter, perhaps to hang up or to change parameters, an escape sequence must be sent.

The industry standard "+++" escape sequence does not hang up the line or interfere with other settings and is entered by pausing for a few seconds, typing pausing again. Do not press

+++

, and then

K

(Carriage Return or Enter). Typing the escape sequence returns you to the On-line Interactive State where the AT commands are active. For example, typing

athK

will hang up the call.

3.8 Advanced Features

The DPX-213 has MNP-4 error correction and MNP-5 data compression software. These are disabled in the factory defaults and must be specifically enabled if required. The

Constant Speed Interface is active by default and allows terminal speeds from 300 to 9,600 bps to be automatically supported. The modem will normally attempt to establish all calls at 2,400 bps unless commanded otherwise or the remote modem cannot support this speed.

The modem automatically adjusts the transmit or receive speed to match the modem at the other end of the link. The line speed of the connection is displayed as the modem goes online.

The Constant Speed Interface facility, error correction and data compression are powerful features, but can result in problems if your terminal does not support flow control. If you are obtaining errors, or characters are garbled or missing whenever these features are invoked, it is likely there is a flow control problem. Check your communications software manual, the flow control sections (see Index) and the relevant AT commands of this manual.

To reduce the risk of unauthorised entry to your system, the DPX-213 features password verification. A password may be stored in the DPX-213 permanently and only those calls meeting the incoming password challenge are allowed access to the host.

The DPX-213 also contains an alarm feature that will dial a remote modem when an external device indicates that an event has occurred. The modem will connect with the remote modem and attempt to send a previously stored string.

Copyright (C) Dataplex Pty Ltd 3-3

BEFORE YOU START

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 3

3-4 Copyright (C) Dataplex Pty Ltd

AT COMMAND SET Section 4

4.0 AT COMMAND SET

This Section contains some useful information about entering commands into the DPX-

213, the 'AT' command syntax and the different operating states. The Section also contains a complete alphabetical listing of all commands.

4.1 Command Line and Command Entry

The DPX-213 uses the common AT command set which Dataplex has extended to cover additional features. The attention code, the letters 'AT', must precede all command lines to the DPX-213. This code may be in either upper or lower case. The modem uses the AT characters to detect the baud rate and character format of the incoming data. In this way, each command line can be at a different baud rate if desired. Once the AT sequence has been entered, the baud rate and character format are fixed for the remainder of that command line.

Typing AT while off-line will alert the internal control processor, but while on-line, the

'pause'

+++

'pause' escape sequence must be entered.

Some AT commands act on S-Registers. These are storage locations where various operating parameters are stored. These parameters control various modem features, such as the number of rings to count before answering an incoming call, the delay after dialling and before carrier detect, and so on. Refer to Section 8 for a full description of the S-

Registers used in the DPX-213.

A command line to the DPX-213 consists of an attention code, one or more commands, and a carriage return (

K

). A command line may contain up to 129 characters

(including the attention code and the carriage return). Should you enter more than 129 characters, the DPX-213 will abort the command and return an ERROR code. Re-enter the command sequence in two smaller command lines.

Commands may be concatenated to save time. For example

at&fs0= 5d1234567K

causes the DPX-213 to recall the factory configuration, set S0=5 (answer telephone on 5th ring) and then dial 1234567.

Do not type AT more than once on any line or the AT character will be interpreted as command and not Attention.

For example you can enter commands separately:

1. Entering

atx3K

will cause the modem to blind dial (not wait for dial tone).

2. Entering

ats0=4K

will cause the modem to answer on the fourth ring.

Copyright (C) Dataplex Pty Ltd 4-1

AT COMMAND SET Section 4

3. Entering

ats7=60K

will cause the modem to wait 60 seconds for carrier from the answering modem.

4. Entering

atdn5K

will cause the modem to dial the number stored in location 5.

Or type one concatenated string:

atx3 s0=4 s7=60 dn5 K

which has the same effect (spaces between commands are ignored and are optional).

The above command descriptions have numeric modifiers to allow selection from one of several command options. These are usually shown as parameters 0 to 9. Where a numeric selection is omitted, the command processor assumes a zero (0) has been entered. For example AT*W is interpreted as AT*W0.

Commands take a variable time to execute, depending on the length of the command line and the type of command. The DPX-213 also takes a short period (750 microseconds) after the end of one command (the transmission of the result code) before it is ready to accept the next command. During this time the DPX-213 is resetting its internal registers in preparation for the next command. If communications equipment sends an 'AT' sequence during this 750 microsecond period, the 'AT' and subsequent command will be ignored.

4.2 Attention Code Syntax

It is possible to disable the AT command sequence by using the AT*D1 (Dumb Mode) command. In this mode, the unit will not respond to any AT sequence. The only way to reset the unit from this state is to carry out a power up reset (if not stored in NVRAM).

A description of the syntax for entry of AT commands follows:

Carriage Return

Command lines end with the carriage return character

K

. The value of this character is stored in Status register S3, and may be changed if desired. The default value of the carriage return is ASCII code 13 {0D HEX}.

4-2

Backspace

If an incorrect entry is made in a command line before key (

K

is depressed, the backspace

E

) can be used to erase the mistake. The backspace key will erase all characters up to, but not including the attention code (AT). The backspace character is stored in Status register S5. The default value is ASCII code 8.

Section 4

Repeat Command

AT COMMAND SET

When the DPX-213 is in Local Command State (waiting for an attention code), entering the characters

a/

will cause the DPX-213 to repeat the last command line. The 'A' character can be in either upper or lower case. If an

a/

on the power, the modem will return an ERROR code.

is entered directly after turning

Command Parameters

Most commands to the DPX-213 have several parameters. These parameters select the various options for each command. Should the parameter be missing for a particular command, the modem will substitute the value 0. Should a parameter be outside the defined range, the modem will return an ERROR code.

Result Codes

After the DPX-213 has executed each command line, it returns a result code to show the status of the command. The result is in the form of digits (0 to 233) or text. Results displayed in digit format are often used when the modem is being controlled by a computer. Results displayed in the text format are suited to terminal control. Result codes can be disabled by setting Quiet Mode (ATQ1).

Status Registers

Configurations are stored in the Status Registers, called 'S-registers'. The DPX-213 has 24

Status Registers (of which, some are reserved for future expansion or used to maintain compatibility with the DPX-224). Most commands in the DPX-213 alter values in the status registers.

4.3 DPX-213 Operating States

There are four distinct operating states for the DPX-213:

1. Idle State

2. Command State

3. Data State

4. On-line command State

A description of each operating states follows.

Copyright (C) Dataplex Pty Ltd 4-3

AT COMMAND SET Section 4

1. Idle State

This state is entered shortly after power is applied to the modem and the power-up self test has been passed. It can also be entered after the modem has executed a nondialling command line. In this state, the modem is waiting to autobaud an AT sequence from the DTE or awaiting a ringing signal from the telephone line. If a valid 'AT' entry is detected, the modem enters the Command State.

If a valid ringing signal is detected the modem will send a RING message to the

DTE at the last autobaud speed. If set to answer (S-Register 0 not set to 0) the modem will go off-hook and enter the Data State after a predetermined number of rings (S0).

2. Command State

During the Command State, the modem buffers command characters from the DTE until a carriage return (

K

) character is received. The modem will buffer up to

48 characters not including the initial 'AT' characters. If more than 48 characters are received the modem will insert a carriage return character and return an ERROR message signifying buffer overflow. If no overflow is detected and a carriage return character is received the modem will start to sequentially execute commands in the buffer until one of the following:

1. Carriage Return Detected

If this is part of a dial command, the DPX-213 will execute the following sequence: go off-hook, look for dial tone (unless set to blind dial) and then proceed to place the call.

2. Illegal Command Encountered

The modem will execute the following sequence: send an ERROR message to

DTE, empty the command buffer and return to idle state.

3. Answer (ATA) or On-line (ATO) Command Received

The modem will enter the Data State.

4-4 Copyright (C) Dataplex Pty Ltd

Section 4 AT COMMAND SET

3. Data State

After an ATA (Answer) or ATO (Originate) command, the modem enters the Data

State. The modem will attempt to handshake with the remote modem or if already connected will enter begin to exchange data.

The normal Data State is transparent and all characters issued by the DTE are passed to the remote end. Sometimes you may need to abort the operation and regain control of the local modem instead of the remote DTE. This is possible in the

On-line Command State and is selected with the escape sequence.

Several other interface or line events that will cause the modem to drop out of transparent data transmission (Data State) to local control (On-line Command State) are described as follows:

1. Escape Sequence Detected ('pause'

+++

'pause')

The modem will leave the data state and execute the following sequence: send an "OK" message to the DTE, clamp transmit data to mark, disable receive data to DTE and enter the On-line Command State.

2. Loss of Carrier Detected (provided S10 is not set to 255)

The modem will execute the following sequence: send a "NO CARRIER" message to the DTE, go on-hook and returns to Idle State.

3. DTR Dropped (provided DTR is not forced on and AT&Dn is set)

The modem will execute the following sequence: send a "NO CARRIER" message to the DTE, go on-hook and return to Idle State.

4. DTR Dropped (provided DTR is not forced on and AT&D2 or AT&D3 is set)

The modem will execute the following sequence: send a 'NO CARRIER' message to the DTE, go on-hook and return to Idle State.

Copyright (C) Dataplex Pty Ltd 4-5

AT COMMAND SET Section 4

4. On-line Command State

This state is entered after a 'pause'

+++

'pause' escape sequence has been detected. The modem link is preserved and the user communicates with the local modem and not the remote DPX-213. All data sent by the remote modem is ignored but carrier is still monitored and the message "NO CARRIER" will be issued if loss of carrier is detected. Additionally, some RTS, DTR, or make busy control changes are acted upon. Any normal command that can be issued in command state can now be issued in the On-line Command State while a call is active. However, some commands have no meaning such as ATA, and will return ERROR. The most common use of the On-line Command State is to issue the ATH command to hang up the call. Other options to exit the On-line Command State are:

1. ATH Command Received

The modem will execute the following sequence: send an "OK" message to the

DTE, go on-hook (hang-up) and return to Idle State.

2. ATZ Command Received

The modem will execute the following sequence: reset the configuration to the customer stored value, go on-hook (hang-up), send an "OK" message to the

DTE and return to Idle State.

3. ATO Command Received

The modem will execute the following sequence: send a "CONNECT" message, unclamp received and transmitted data, and returns to the Data State.

4.4 AT Command Set

The remainder of this Section contains an alphabetical listing of all commands, including full syntax and details of use. For each command, parameters, default settings (or AT&F) and the Status Register (S-register) bits that store the present command setting are provided. If the value in a status register effects the operation of a command, the register with its default value is shown. For example: S7 (45 seconds).

4-6 Copyright (C) Dataplex Pty Ltd

Section 4

A/ Repeat Last Command

Parameters : None

Default : None

AT COMMAND SET

A/ is the only command that must not be preceded by an "AT" or terminated with a carriage return (

K

). This command will repeat the preceding command string. This is useful for redialling a previously engaged phone number.

ATA ANSWER

Parameters : None

Default : None

Causes the modem to answer an incoming call (go off-hook), try to train on the incoming signal and then go on-line. There will be a 2.1 second delay to pass STD beeps, billing meter pulses and the modem's answer tone. If the modem fails to detect carrier within the time stored in register S7 (45 seconds), the modem will go on-hook and return to Local

Command State. The modem ignores all commands in a command line following the

Answer command.

ATB BELL/CCITT Select

Parameters : 0 or 1

Default : 0 (CCITT Modulation)

This command selects CCITT or BELL modulation format for signaling to line. In conjunction with the ATFn command, the user can force the line speed and modulation to a predetermined format instead of relying on the autoranging capabilities of the DPX-213.

The command is useful when placing international calls to Bell modems. Refer to the ATF command description for full details on autoranging and other settings. The Bell 103 Mode is only available when the Constant Speed Interface is disabled via the AT&I0 command.

Table 4.1 CCITT and Bell Selection

SPEED

ATB0

ATB1

300

ATF1

V.21

Bell 103

1200/75

ATF3

V.23

1200

ATF4

V.22

Bell 212

2400

ATF5

V.22bis

CCITT

Bell

Copyright (C) Dataplex Pty Ltd 4-7

AT COMMAND SET Section 4

4-8

ATD DIAL

Parameters : Dial String

Default : None

Causes the modem to go off hook and originate a telephone call. After dialling, the modem will wait for an answer tone from the remote modem, try to train on the incoming signal, and go online. If the modem fails to detect an answer tone after the time in register S7 (45 seconds), the modem will return to the Local Command State and send the "NO

ANSWER" message.

The modem will dial all 10 pulse digits or 12 standard tone pairs. These digits may be separated by spaces. Certain modifiers will effect the way the number is dialled and are listed below. The dial string consists of telephone number digits and dial modifiers.

Acceptable dial digits are the numbers 0-9 (zero through to nine) and the symbols * # (for tone dialling only). Acceptable dial modifiers are Nn P T and , (comma).

The DPX-213 ignores any other characters in the dial command. These can be freely used to improve readability.

atd1234567K

is equivalent to:

atd (03) 123-4567K

Entering the dial string with no parameters causes the modem to try to establish a connection without dialling any digits. This can be used in leased line Mode in conjunction with the Answer command to make a connection.

Dial Modifiers

Dial modifiers are used with the dial command to instruct the modem to perform different dialling features. They can be placed anywhere in the dial string.

Nn Dial stored number where n = 0 to 9.

P Set pulse dialling.

Set tone dialling.

Pause for time in status register S8 (Default = 2).

Nn - Dial Stored Number

The ATDN command, followed by a number from 0 to 9 instructs the modem to dial the number stored in that memory location. The numbers are stored into the memory locations by the AT&Z command. AT&N will display all 10 stored numbers. If n = 0 or no number is given, the modem dials the number in location N1.

Section 4 AT COMMAND SET

P - Set Pulse Dialling

Normally the DPX-213 will automatically sense whether to use tone or pulse dialling.

Using this modifier causes any further digits in the dial string and if ATX3 is set, dial commands, to be dialled with decadic pulses. Thus, pulse and tone dialling may be mixed in the same telephone number. The default setting is for check for tone dialling. If ATX4

(check for dial tone) is set, the DPX-213 will dial the first digit of a dial string in tone mode and recheck for dial tone. If dial tone is still present, the entire number will be dialled in pulse mode, otherwise, the rest of the number will be dialled in tone mode.

T - Set Tone Dialling

Causes any further digits in the dial string (provided ATX3 is set) or dial commands to be dialled with DTMF tones. Pulse and tone dialling may be mixed in the same telephone number. If ATX4 (check for dial tone) is set, the DPX-213 will dial the first digit of a dial string in tone mode and recheck for dial tone. If dial tone is still present, the entire number will be dialled in pulse mode, otherwise the rest of the number will be dialled in tone mode. A 'T' or 'P' command in a dial string will override the automatic tone/pulse selection.

, (comma) - Pause

Causes the modem to wait for the time in register S8 (2 seconds) before continuing.

Sometimes used after dialling the STD codes before dialling the rest of the telephone number. For example:

atd03,1234567K

ATDn DIAL Stored Number

Parameters : 0 to 9

Default : 0 (act on Number in location zero)

The ATDNn command causes the DPX-213 to go off-hook and dial the number stored in location n. It is equivalent to typing ATD followed by the valid dialling characters stored in location n.

ATE Command ECHO

Parameters : 0 or 1

Default : 1 (Echo Enabled)

The ATE command controls the echoing of characters from the DTE in local command state.

ATE0 - Disable Local Echo.

ATE1 - Enable Local Echo. The modem echoes all characters from the local DTE.

Copyright (C) Dataplex Pty Ltd 4-9

AT COMMAND SET

ATF FORCE Line Speed

Parameters : 0 to 6

Default : 0 (Auto Speed)

Section 4

This command lets you select the transmission speed and modulation format independent of the DTE interface speed. Use this command in conjunction with the ATB command.

This allows you to go on-line at 300, 1200 or 2400 bps but keep your terminal speed fixed at some other speed.

ATF0 - Modem autoranges for both originate and answer. The Constant Speed Interface

operates from 300 to 9,600 bps. The DPX-213 will accept incoming calls at

300,1200 or 2400 bps.

ATF1 - Selects 300 bps. CCITT or Bell selected by ATB.

ATF2 - Not used. Responds with ERROR.

ATF3 - Not used. Responds with ERROR.

ATF4 - Selects V.22 or Bell 212A 1200. Speed fixed at 1200 bps.

ATF5 - Selects V.22bis. Speed fixed at 2400 bps.

ATF6 - Similar to ATF0 except that once a connection is established, forces DTE speed to

line.

The DPX-213 will autorange on both answer or originate. Set ATF0 at the answering modem and it will adjust speed automatically to accommodate the incoming call. If the

Constant Speed Interface (AT&I1) is set, the DTE speed will be the last autobaud speed

(except when ATF6 is used).

ATH HOOK Control

Parameters : 0 or 1

Default : 0 (modem On-hook)

Controls the hook relay, connecting and disconnecting the modem from the telephone line.

ATH with no numeric suffix is interpreted as ATH0 and causes the modem to hang up (go on-hook) and return to the Idle State.

ATH0 - Forces the modem to go on-hook and return to Idle State.

ATH1 - Forces the modem to go off-hook (on-line).

4-10

ATI IDENTIFICATION

Parameters : 0 to 3

Default : 0 (Display "DPX-213")

Returns the modem identification codes to your terminal.

ATI0 - Return modem product code. The DPX-213 sends "DPX-213".

ATI1 - Return ROM checksum.

ATI2 - Return result of checksum verification. The DPX-213 sends "OK" if the checksum verifies.

ATI3 - Return software revision number.

Section 4

ATNn&Z Store String in NVRAM

Parameters : 0 to 9

Default : None

AT COMMAND SET

This command allows up to 44 characters to be stored in each of the ten NVRAM locations for later recall.

NOTE: Location zero and location one are the ONLY locations that can be dialled on the rise of DTR.

Locations may hold Alarm Mode text strings (2,3,4), Passwords (5,6,7,8,), numbers to dial on the raise of DTR (0,1) and number to dial with the ATDNn command for security callback after a password match (any location). For example:

LOCATION CONTENTS

DTR / n0 Dial Number.

Alternate DTR / n1 Dial Number

Alarm Mode Connect String / n2 Dial Number

DTR Raised String / n3 Dial Number

Keyboard Activity Alarm String / n4 Dial Number

Password Storage / n5 Dial Number

Password Storage / n6 Dial Number

Password Storage / n7 Dial Number

Password Storage / n8 Dial Number

Password String / n9 Dial Number

When a stored number is recalled via the ATDNn command, the command processor effectively enters ATD, fetches location n and then dials the digits in the order it finds them.

ATO On-line, ORIGINATE and Retrain

Parameters : 0

Default : 0

If the modem is already online, this command causes the modem to return to the Data

Transfer State. If the modem is not online, the modem will attempt to originate a call (go off hook and wait for answer tone). The modem ignores all commands in a command line following the Originate command.

ATO0 - Return to On-line State or originate a call.

Copyright (C) Dataplex Pty Ltd 4-11

AT COMMAND SET Section 4

ATP Set PULSE Dialling

Parameters : None

Default : None

If ATX3 (do not listen for dial tone) is set, ATP causes the DPX-213 to dial any further dial commands with decadic pulses. If ATX4 (check for dial tone) is set, then regardless of the state of the ATP command, the DPX-213 will dial the first digit of a dial string in tone mode and recheck for dial tone. If dial tone is still present, the entire number will be dialled in pulse mode, otherwise the rest of the number will be dialled in tone mode.

ATQ QUIET Mode

Parameters : 0 or 1

Default : 0 (Enable dialling messages)

This command controls whether or not the modem sends messages and result codes (such as "OK") to the DTE as it executes commands (some software packages may not recognise call progress messages); the AT command itself will still be echoed (unless ATE0 is active).

ATQ0 - Enables command and call progress messages to be sent to the DTE.

ATQ1 - Enables Quiet Mode and ensures no messages are passed during call placement.

When ATQ1 is in use, sufficient time must be allowed for each command issued to

be executed or closely spaced commands may be misinterpreted by the modem.

ATSr? Read STATUS Register Contents

Parameters : r = 0 to 53

Default : 0 (Display Register 0)

This command will return a three digit decimal value of the selected S register, r. The display is always in decimal, even for bit mapped registers.

4-12 Copyright (C) Dataplex Pty Ltd

Section 4 AT COMMAND SET

ATSr=n Set STATUS Register Contents

Parameters : r = 0 to 53, n = 0 to 255.

Default : r = 0, n = 0

The ATSr=n command allows the user to change the modem configuration parameters by altering the values stored in the S registers. You must first convert a binary bit mapped register into decimal before attempting to set it. Use the S register descriptions and

Appendix B to get the correct bit number. This command should be used with care, as loading incorrect results into the S registers can produce unpredictable results. Type

at&fK

to reload the factory default settings if the S registers become corrupted.

ATT Set TONE Dialling

Parameters : None

Default : None

This command enters the tone dial mode and awaits the next ATDnnnn command. Typing

attK

is a valid entry. Additionally, typing 'T' within a dial string such as the following command string:

atdt 1234567K

is acceptable. This command overrides the automatic tone/pulse dialling selection only when used as a dial modifier.

ATV Set VERBOSE Response Codes

Parameters : 0 or 1

Default : 1 (Verbose Mode)

Determines whether the DPX-213 returns result codes from commands to the DTE in text format or digit/numerical format (Verbose or Terse). Most communications programs use digit responses to determine command status.

ATV0 - Selects digit (terse) responses; digit code is followed by a carriage return.

ATV1 - Selects verbose or text responses; word code is preceded and followed by a

carriage return character (S-register 3) and a line feed character (S-register 4).

Copyright (C) Dataplex Pty Ltd 4-13

AT COMMAND SET Section 4

4-14

ATX Call Progress Control

Parameters : 0 to 3

Default : 3

The ATX command controls the level of call progress detection when originating or answering a telephone call. The table on the following page shows the result codes returned.

ATX0 - Enables response codes 0-4, 8, 12-14 modem will blind dial.

ATX1 - Enables response codes 0-4, 6-8, 12-14 modem needs dial tone.

ATX2 - Enables response codes 0-5, 8-10, 12-21 modem needs dial tone.

ATX3 - Enables response codes 0-10, 12-21 modem will blind dial.

The term 'blind dialling' refers dialing without trying to detect a dial tone. This is useful when the dial tone is a low level or non-standard dial tone as found with some PABX's.

The auto tone or pulse dial detection feature of the DPX-213 is only enabled when the modem is not blind dialling and when it is configured to detect dial tone.

The available response codes that are selected by the ATXn command are shown below.

Table 4.2 Response Codes

Digit Code Description

CONNECT

RING

NO CARRIER

ERROR

CONNECT 1200

NO DIAL TONE

BUSY

NO ANSWER

10 CONNECT 2400

12 LOOP GRANTED

13 RDL DENIED

14 RDL ACCEPTED

16 CONNECT 1200/REL

17 CONNECT 2400/REL

18 LOOP GRANTED/REL

19 CONNECT 1200/REL

20 CONNECT 2400/REL

21 ABORTED

Command executed without error.

Modem connected at any speed if ATX0 enabled.

Incoming call detected.

Carrier not detected after S7 timeout or carrier lost.

Illegal command or buffer overflow.

Modem connected at 1200 bps.

Dial tone not detected.

Busy signal detected, call aborted.

Remote did not answer.

Modem connected at 2400 bps.

Reserved

Local or remote modem in loop.

Remote modem has refused RDL request.

Local modem has accepted RDL request.

Modem connected at 1200 MNP 2-5.

Modem connected at 2400 MNP 2-5.

Local or remote modem in loop with MNP.

Modem connected at 1200 MNP 2-4.

Modem connected at 2400 MNP 2-4.

Connection attempt aborted by operator.

Section 4

ATZ Modem Reset

Parameters : 0,1

Default : None

AT COMMAND SET

Entering ATZ0 resets the modem and copies the user stored NVRAM configuration to the active RAM. It restores all user controlled settings to previously stored values. If the

NVRAM contains an invalid configuration, typing ATZ will merely copy the bad data from NVRAM to active RAM. You must use AT&F (load factory configuration from

ROM to RAM) followed by AT&W (write RAM configuration to NVRAM) to recover from this.

If the modem is in the On-line Command State this command will terminate the call and the modem will return to the Idle State after the command is processed. See also the AT&F command which copies the factory defaults from ROM into the active RAM.

If ATZ1 is entered, the unit will be placed in the very low power standby mode (depending upon DTR level and setting of jumper J5). The modem may be woken from this state by either raising the DTR, activity on DTE Txd, Ring detection or power cycle. When the modem is in standby mode the unit is effectively switched off. If a unit is on line the connection will be lost.

AT&C CARRIER Detect Control

Parameters : 0 or 1

Default : 0 (CD Pin 8 always High)

This command controls the status of both the CD lead (Pin 8) in the V.24/RS-232 interface and the front panel CD LED.

AT&C0 - V.24 Pin 8 CD and LED always forced on.

AT&C1 - V.24 Pin 8 CD and LED follows phone line data carrier.

AT&D DTR Control

Parameters : 0 to 3

Default : 0 (DTR Always On)

This command controls events on the fall of DTR (Data Terminal Ready). See the AT&M command for interactions on the rise of DTR. When this command is enabled, the DTR lead must be high for the modem to operate correctly.

AT&D0 - DTR input ignored.

AT&D1 - Modem set to Command State when DTR drops (as for escape sequence).

AT&D2 - Modem set to on-hook and returns to Command State when DTR drops

(ATH).

AT&D3 - Modem initializes (executes ATZ) when DTR falls.

Copyright (C) Dataplex Pty Ltd 4-15

AT COMMAND SET

AT&E ERROR Correction

Parameters : 0 or 1

Default : 0 (MNP disabled)

Section 4

AT&En enables or disables error correction and data compression in the DPX-213. When used with the AT&I1 Constant Speed Interface command, the terminal can operate at 4800 bps to 9,600 bps to take full advantage of data compression. Error control or data compression is not supported at V.21 (300 bps) speeds and in one of the two leased line modes.

AT&E0 - Error control/data compression disabled.

AT&E1 - MNP-2 to MNP-4 error correction enabled. The highest level automatically

negotiated by modems. If no remote MNP is found, the modem will fall back to

Constant Speed Interface mode or disconnect if AT&I0 is set.

When MNP modems connect, one of the modems must send a request packet (MNP) to initiate the negotiation. By convention, this is normally the originating modem. If the modem is connected to a non MNP modem this request will appear as corrupt characters to the DTE on the non MNP modem. Therefore, the default setting is MNP off.

NOTE: If MNP is to be used, both modems must support it and at least one modem must request it.

4-16

AT&F Load FACTORY Configuration

Parameters : None

Default : None

This command copies the factory defaults from fixed EPROM into working RAM. This is useful for restoring the modem to a preset configuration. To use the factory defaults in normal operation, type

at&fK

then make them permanent by typing

at&wK

AT&G GUARD Tone Control

Parameters : 0 or 1

Default : 0 (no Guard Tone)

Guard tone is typically used to disable echo cancellers within the U.K. It is only active in

1200 bps and 2400 bps operation. The modem sends guard tone to line to disable echo suppressors. Echo suppressors are desirable for voice lines where one party talks and the other listens, but undesirable for full duplex data lines where both ends are transmitting simultaneously. Echo suppressors are rarely used in Australia. Guard tones are only active when operating in V.22bis mode, and only on the answering modem.

AT&G0 - No Guard Tone.

AT&G1 - 1800Hz or 550Hz Guard Tone (depends on Bell setting, ATB0 enables 1800Hz).

Section 4

AT&H HELP

Parameters : 0 to 4

Default : None

AT COMMAND SET

This command displays several levels of help screens to reduce the need for a handbook to enter field changes.

AT&H0 - General help Summary.

AT&H1 - Extended help Summary.

AT&H2 - Help on Dial Modifiers.

AT&H3 - Help on Test Commands.

AT&H4 - Help on S-Registers.

AT&I Constant Speed INTERFACE

Parameters : 0 or 1

Default : 1 (enable Constant Speed Interface)

The AT&I command allows the data rate of the DTE to be at a uniform rate, regardless of the rate determined by the communication format (specified by ATFn). This is useful if the

DTE can only operate at a single speed and when error correction is enabled. It can also control whether a connection will be established or rejected if the MNP negotiations fail.

AT&I0 - Disable Constant Speed Interface. The modem will autobaud on the DTE rate

before the call, but will change the interface speed to that of the actual line

connection as soon as the call is established. For example, if your terminal is set

for 2400 bps and the DPX-213 can only establish a link at 1200 bps, the

message "CONNECT 1200" will be displayed at the 2400 bps autobaud rate and

then the interface will change to 1200 bps. Therefore, the terminal speed must be

changed to continue without errors. Some communications packages read the

"CONNECT XXXX" message and can be instructed to change your DTE speed

automatically. Also, the 'pause'

+++

'pause' escape sequence will need to

be sent at 1200 bps to be recognised.

AT&I1 - Enable Constant Speed Interface. The data to and from the terminal will be at the

last autobaud speed regardless of the actual connection speed. DTE speeds above

2400 bps (or faster than the actual on-line rate) can cause data to enter the

modem faster than it can be sent to line. Therefore, unless the AT&K and AT&U

flow control commands are set, data may be lost in buffer overflows.

The AT&I1 command in conjunction with AT&E1 or AT&E2 (MNP-4 or MNP-5) ensures a dial link will be established regardless of whether or not the remote modem can support

MNP.

Copyright (C) Dataplex Pty Ltd 4-17

AT COMMAND SET

AT&K DTE Flow Control

Parameters : 0 to 3

Default : 1 (Select Xon/Xoff Flow Control)

Section 4

This command selects the method of handshaking between the DTE and the modem during error correction, data compression or whenever the Constant Speed Interface is set at a different rate to the line speed.

NOTE: Xon/Xoff flow control should NOT be used when passing binary, command or executable files since they may contain Xoff characters without matching Xon characters. The modem may appear to 'lock up' and Xoff characters may be introduced or lost, thus corrupting the file. Use hardware flow control (RTS/CTS) for binary file transfers.

AT&K0 - Disable flow control. The DTE must be careful not to overflow the buffers or

data will be lost.

AT&K1 - Xon/Xoff ( ###

q

/ ###

s

) enabled. The modem can control the flow of

data by issuing an Xoff to the DTE. The Xon and Xoff characters can be altered

from their defaults and are stored in locations S33 and S32 respectively. Both

the modem and the DTE must halt whenever they receive an Xoff character and

not restart until they receive an Xon character.

AT&K2 - Enables RTS/CTS hardware flow control. When set, the modem drops Clear To

Send (CTS) whenever the buffers are almost full. The DTE may also flow

control the modem by dropping RTS.

AT&K3 - Enables both RTS/CTS and Xon/Xoff flow control. This is equivalent to

issuing the commands AT&K1 and AT&K2. Be sure to terminate RTS and CTS

correctly when using this command.

NOTE: Whenever AT&K2 or 3 are invoked, the RTS and CTS leads must be correctly driven and not left floating in the interface cable.

4-18 Copyright (C) Dataplex Pty Ltd

Section 4

AT&L LEASED Line Select

Parameters : 0 or 1

Default : 0 (Dial Network)

AT COMMAND SET

The CCITT V.22bis recommendation is primarily concerned with dial network operation.

Leased line operation with different manufacturers products may not be entirely successful. The DPX-213 supports leased line operation at 1200 and 2400 bps in both

AT&L0 and AT&L1 modes. Data transfer at 300 bps is only supported in AT&L1 mode and data transfer at 1200/75 V.23 is not supported in either leased line mode.

AT&L0 - Dial Network Mode.

AT&L1 - Enable speeds 300, 1200 and 2400 bps only. MNP/V42 and the Constant Speed

Interface are disabled in this Mode. Synchronous or Asynchronous Mode is

selected via the AT&Mn commands. The AT&D0 (ignore DTR) effectively

overrides the DTR Pin on the interface. Setting AT&D0 with AT&L1 forces the

DPX-213 on-line immediately regardless of the DTR status. This is the

recommended mode for interworking with the DPX-224 or TEL-424 modems.

Configure the modem for leased line operation as follows:

1. Set AT&D1 mode.

2. Issue the AT&L1 command to select Leased Line Mode.

3. Set register S0=0 at one end to force Originate Mode.

4. Set register S0=1 at the other end to force Answer Mode.

5. Enter AT&M1 mode.

6. Raise DTR at both ends to establish the link.

Once connected the escape sequence 'pause'

+++

'pause' is entered, control may be regained and allow entering the ATH command if needed. Alternatively, the DTR may be dropped to return to Command Mode. In synchronous (AT&M2 or AT&M1) Mode, dropping DTR will terminate the call. In asynchronous (AT&M3) Mode, dropping DTR will follow the AT&Dn command.

All keystrokes are ignored during leased line call establishment phase.

NOTE: The line interface cable must be modified as shown in Appendix D for correct operation in leased line modes.

Copyright (C) Dataplex Pty Ltd 4-19

AT COMMAND SET

AT&M Synchronous/Asynchronous MODE Selection

Parameters : 0 to 3

Default : 0 (Async)

Section 4

The AT&M command selects asynchronous or synchronous terminal modes of operation.

This command also provides for the manual and automatic dialling of a stored number under DTR control. See the AT&D command for actions taken on the fall of DTR.

AT&M0 - Asynchronous Mode 0. Type ATDnnn to dial.

AT&M1 - Synchronous Mode 1. DTR dial asynchronous. Enabling this Mode will cause

the modem to dial the number in location zero on raise of DTR. AT&Dn must

be correct.

AT&M2 - Synchronous Mode 2 (with asynchronous terminal dialling). Use an

asynchronous terminal to place the call and then change to Synchronous Mode

once the call is placed.

AT&M3 - Synchronous Mode 3. DTR dial synchronous. Enabling this mode will cause

the modem to dial the number stored in location zero on raise of DTR.

AT&N Display/Clear Dialling Directory

Parameters : None or 99

Default : None

AT&N will display the 10 telephone number storage locations with their contents. Any numbers which require alteration can be updated individually with the ATNn&Z command.

The AT&N99 command erases all 10 locations.

4-20

AT&P PULSE Dial Make/Break Ratio

Parameters : 0,1

Default : 1 (CCITT Make/Break Ratio)

This command allows the user to select the pulse dialling make to break ratio.

AT&PO - Bell Make/Break Ratio (US setting).

AT&P1 - CCITT Make/Break Ratio (Australian setting).

Section 4

AT&T TEST Modes

Parameters : 0 to 6

Default : 0 (No Tests in Progress)

AT COMMAND SET

This command enables and disables several local and remote loopback tests, and tests with the internal test pattern generator.

AT&T0 - Terminate test in progress.

AT&T1 - Initiate Local Analog Loopback.

AT&T4 - Enable Remote Digital Loopback response.

AT&T5 - Disable Remote Digital Loopback response.

AT&T6 - Initiate Remote Digital Loopback

AT&U USER Flow Control

Parameters : 0 to 3

Default : 0 (Flow Control off)

This command affects flow control in the modem. AT&Un is only active while MNP /V42 is disabled and while the Constant Speed Interface is enabled. If MNP/V42 is enabled then

AT&U can remain at the defaults. Refer to the Data Transfer Section (Section 6) for more details. The commands AT&En, AT&Kn, AT&In and AT&Un all influence flow control and must be correctly set for your application.

Whenever AT&Un is invoked, Xon/Xoff characters may be inserted in the data stream and corrupt a binary file transfer. Alternately, an Xoff character encountered in a binary file transfer will halt the modem. Select AT&U0 (off) for binary file transfers.

AT&U0 - Pass through off, line flow control off.

AT&U1 - Pass through enabled, line flow control off.

If Xon/Xoff flow control is active (AT&K1 or AT&K3), Xon/Xoff characters

through from the DTE to the line side buffers of the modem - after being acted

upon.

AT&U2 - Pass through off, line flow control on.

This selection is only valid if RTS/CTS handshaking (AT&K2) is selected. In

this mode, any flow control characters detected in the data received from line

will be acted upon by the line buffer but not passed to the DTE buffer.

AT&U3 - pass through on, line flow control on.

This selection is usually used with DTE flow control set to RTS/CTS, AT&K2.

Flow control characters received at the line buffer will be acted upon and then

passed to the DTE via the DTE buffer. The DTE will be operating in a mode

that enables it to respond to both RTS/CTS and Xon/off flow control. In this

way both the local modem and the remote DTE may flow control the far modem

and DTE.

Copyright (C) Dataplex Pty Ltd 4-21

AT COMMAND SET Section 4

Pass through means that, if Xon/Xoff flow control is enabled, the controlling character detected will be acted upon by any buffer it encounters, and then passed through to the next buffer in the link. Disabling pass through means that any Xoff character received by a buffer will be obeyed but the Xoff character will then be discarded. If line flow control is enabled, the receiving modem line buffers will be susceptible to flow control characters in the received data stream.

AT&W WRITE Active Configuration to NVRAM

Parameters : None

Default : None

Whenever power is applied to the DPX-213, or the modem is reset (ATZ), the status registers are loaded with values saved in the non volatile RAM. AT&W allows a particular configuration to be saved in the non volatile RAM and then reloaded the next time power is applied to the modem or the reset (ATZ) command is issued. The interface speed is also saved and becomes the default speed for the subsequent incoming calls (and after power cycling).

AT&Z Store Telephone Number

Parameters : Dial String

Default : N/A

This command stores a dial string in non volatile RAM for dialling later with the ATDNn command. Any valid dial string (see the ATD command) can be stored and up to a maximum length of 36 characters. Any characters after this will be ignored. The storage location to be overwritten by the AT&Z command is set by the ATN command.

4-22

To invoke the dial string type

atdnK

with no other characters. Dialling by pulse or tone dial will be by the default or the last used method. The more general storage/access command is ATNn&Z, which gives access to all 10 storage locations.

Section 4

**AT*A Alarm/Alert Mode**

Parameters : 0 to 3

Default : 0 (Alarm off)

AT COMMAND SET

This command enables the Alarm function on the DPX-213.

AT*A0 - Alarm function disabled.

AT*A1 - Enabling this command will cause the modem to dial the number stored in

location 0 upon "wake up". When connected, the modem will send the string

stored in location 1. If the modem is woken by DTR, it will send the string stored

in location 2; if woken by TxD, it will send the string stored in location 2 and if

woken by Ring, the modem will ignore ring and then dial and send strings in

locations 1 and 4 respectively.

AT*A2 - The modem will "wake up" on any Ring, raise of DTR or TxD from DTE. By

invoking the AT&M command, the unit will dial the number stored in location 0

on rise of DTR and send the relevant alarm string on connection. Otherwise, the

modem will wait for an AT command or Answer when the ring limit is reached.

If the AT command originates the call then the alarm string is sent on call

connection, however, if the modem has answered the call then no alarm string is

sent.

AT*A3 - Reserved for future use.

See applications section for full description of this function.

**AT*C Configuration Status**

Parameters : None

Default : None

The AT*C command will display the active modem configuration. The table below shows the default (AT&F) configuration.

CONFIGURATION

B Bell/CCITT

E Echo

F Format

T/P Tone or Pulse

X Result Code

&C DCD Option

&D DTR Option

&E Error Control

&G Guard Tone

&I Constant Speed

&K DTE Flow Control

&L Leased Line

STATUS CONFIGURATION

&M Sync/Async

&P Pulse Ratio

&T RDLB Enable

&U DCE Flow Control

*A Alarm Mode

*D Dumb Mode

*E Compression

*G Calling Tone

*P Password

*R Remote configuration

*Y Break Handling

STATUS

Copyright (C) Dataplex Pty Ltd 4-23

AT COMMAND SET Section 4

**AT*D DUMB Mode**

Parameters : 0 to 3

Default : 0 (Disabled)

To prevent modem "lock up", it is advised that the escape sequence 'pause'

+++

'pause' be disabled when using the Dumb Mode (see Register S2 description for more details).

AT*D0 - Allows the DPX-213 to respond to normal AT command and attention sequences.

AT*D1 - Disables AT command acceptance and echo. Once the modem is configured, AT

commands can no longer gain control of the DPX-213. The modem will still

abort connect sequence if a key is pressed during the training sequence.

AT*D2 - Disables call placement abort on DTE activity. If characters are sent to the

modem during call connect sequence the modem will ignore them.

AT*D3 - Equivalent to activating both AT*D1 and AT*D2.

**AT*E Data Compression**

Parameters : 0 or 1

Default : 0 (Data compression disabled)

AT*E controls the data compression feature of the modem during error corrected connections. The AT*E command must be used in conjunction with the AT&E command.

AT*E0 - MNP 2-5 data compression disabled.

AT*E1 - MNP 2-5 error correction and data compression enabled. The highest level is

determined by modem negotiation. The modem will fall back to CSI or disconnect

if no remote MNP is detected.

4-24

**AT*G Calling Tone**

Parameters : 0 or 1

Default : 0 (Disabled)

AT*G enables the CCITT recommended V.25 calling tone. This is an intermittent 1300Hz tone generated by the originating modem during the connection phase of a call.

AT*G0 - Causes the DPX-213 to be silent when calling.

AT*G1 - Enables an interrupted 1300 Hz tone to be sent by the calling DPX-213 after

dialling and before the remote modem carrier is detected.

Section 4

**AT*P Password Security**

Parameters : 0 to 2

Default : 0 (Password Disabled)

AT COMMAND SET

The AT*Pn command enables several levels of password and dial back security in the

DPX-213. Refer to Section 5, Applications, for more information.

AT*P0 - Disable password checking.

AT*P1 - Enable password checking. Password prompt can be programmed by placing the

required string in location 9. If no password prompt is specified, the DPX-213

issues a "PASSWORD ? :" prompt for incoming caller. Passwords can be

placed in locations 5 to 8. If no passwords are present, the unit will not connect.

If a passwords are specified, the call originator has 20 seconds per attempt to enter

the correct string. Once 3 attempts have been made, the modem will disconnect.

AT*P2 - Password will dialback.

NOTE: Password security is not available in non CSI/MNP modes (AT&I0 and AT&E0)

**AT*R Remote Configuration**

Parameters : 0 or 1

Default : 0 (Disabled)

This command enables and disables the remote configuration option. When remote configuration is enabled a remote user can modify the configuration on the DPX-213 using the 'pause'

---

'pause' escape sequence or view configuration/setups of the remote modem. Any AT command which does not hang up the modem can be issued in remote configuration Mode.

AT*R0 - Disable remote configuration.

AT*R1 - Enable remote configuration.

NOTE: While in Remote Configuration, the user will be prompted with an ROK> every 20 seconds by the remote modem if no commands are issued.

**AT*Y Break Mode Control**

Parameters : 0 or 1

Default : 0

The AT*Y command controls the processing of break characters from the DTE when the modem is on-line. Refer to the break handling in non-MNP/V42 and non-CSI operation.

AT*Y0 - Pass break immediately to the other end. Leave data in modem buffers at each

end intact. Expedited Non-destructive Break Handling.

AT*Y1 - Pass break immediately to other end but flush all data buffer. Expedited

/Destructive Break Handling.

Copyright (C) Dataplex Pty Ltd 4-25

AT COMMAND SET

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 4

4-26 Copyright (C) Dataplex Pty Ltd

APPLICATIONS Section 5

5.0 APPLICATIONS

This Section describes some essential information about configuring the DPX-213 to operate under various applications.

5.1 Resetting the Modem

Remove the lid from the box and short reset pads while switching the power on. This executes a MASTER RESET which totally clears all stored numbers, stored commands, passwords and S-registers from NVRAM and then loads the factory defaults from

EPROM.

5.2 Operating Modes

There are 4 operating modes on the DPX-213. The first two are asynchronous only and the remaining two are synchronous operating modes.

NOTE: There is some interaction between the Data Terminal Ready (DTR) AT&Dn commands and the AT&Mn operating Mode commands (as shown in the AT&Mn command description tables).

The DPX-213 supports synchronous operation at 1200 bps in both CCITT and Bell Modes, and 2400 bps in CCITT V.22bis Mode (to disable synchronous clocks, short J8 Pin 1 and

2). Before synchronous operation can be established, the correct AT commands must be loaded with using an asynchronous terminal and the subsequent configuration stored in

NVRAM (EEPROM). The DPX-213 does not support V.25bis dialling methods. To enable synchronous clocks, place a jumper across Pins 2 and 3.

Some special conditions exist for the two synchronous modes, AT&M2 and AT&M3. If

AT&D1 to AT&D3 is set, answering takes place when both the ring count and the DTR high condition is reached. If the DTR lead is raised before the count stored in register S0, the modem will go on-line in Originate Mode. If DTR is raised after S0 is reached (but before the 8 second reset period stored in S0) the modem will go on-line in Answer Mode.

For all Synchronous Modes, the suggested starting values and sequences are: AT&F,

AT&C1, AT&D2, AT&M2 or AT&M3

Copyright (C) Dataplex Pty Ltd 5-1

APPLICATIONS

5.3 Asynchronous Modes

Section 5

Mode 0 Asynchronous

This is the standard default Asynchronous Operating Mode. Enter ATDnnnnnn to dial and go on-line. DTR modes refer only to actions performed on the falling edge. Dialling is performed exclusively by AT dial commands. If AT&D0 is set, answering a call takes place as soon as the ring count in S0 is reached. If DTR is left high, the modem will answer on the number of rings stored in S0, or, as determined by the AT&D1-3 modes.

ASYNC MODE

AT&M0&D0

AT&M0&D1

DTR RISE

Ignore DTR.

DTR FALL DTR LOW

AT&M0&D2

AT&M0&D3

Ignore DTR.

On-line Command

State.

Hangup and go to

Command State.

Execute ATZ & hang up.

Ignore DTR.

Do not answer.

Table 5.1 Mode 0 Asynchronous

Mode 1 Asynchronous

This mode allows the DPX-213 to dial the number stored in location zero on the rise of

DTR. If no dialling is desired, the user should ensure location zero is empty for the originating modem or have R stored (for reverse mode) in location zero at the answering end. After a call has been placed by the rise of DTR, the remote modem may disconnect and the local modem may then be in the DTR high, but in the Off-line State. If this is the case, the modem will answer after S0 rings.

If DTR is low and the phone is ringing, the "RING" message will be output to the DTE. If

DTR is raised while the phone is ringing, the modem will go on-line in Originate Mode

(provided the S0 count has not been reached), or alternatively, go on-line in Answer Mode if the S0 value has been passed.

ASYNC MODE

AT&M1&D0

AT&M1&D1

DTR RISE

Ignore DTR.

DTR FALL

Ignore DTR.

DTR LOW

Ignore DTR (answer on S0).

Do not answer.

AT&M1&D2

AT&M1&D3

Dial number.

Table 5.2

On-line Command

State.

Hang up and go to

Command State.

Execute ATZ and hang up.

Mode 1 Asynchronous

Do not answer.

5-2 Copyright (C) Dataplex Pty Ltd

Section 5

5.4 Synchronous Modes

APPLICATIONS

Mode 2 Synchronous

This is useful for setting up a synchronous auto-answer system or setting up a synchronous link with an asynchronous terminal and then switching over to a synchronous DTE with an

A/B switch once the call is established.

With AT&M2 set, the DPX-213 allows asynchronous dialling (for example

ATDP1234567). After call establishment (the modem issues the "CONNECT" message), the modem enters Synchronous Mode and turns on the clocks. It then waits the period stored in Register S25 before examining the DTR line. This allows time to switch over to a synchronous DTE. If DTR is high (ON) when S25 expires, the DPX-213 continues in

Synchronous Mode with clocks at the speed of the connection. If DTR is low (OFF), then the modem takes the action specified by the AT&D setting.

After a call has been placed by the rise of DTR, the remote modem may disconnect and the local modem may then be in the DTR high but off-line state. If this is the case, it will answer after S0 rings. If DTR is low and incoming ring is detected, the "RING" message will be output to the DTE. If DTR is raised while the phone is ringing, the modem will go on-line in Originate Mode (provided the S0 count has not been reached), or go on-line in

Answer Mode if the S0 value has been passed.

In all other synchronous modes, the AT&D command is ignored and if DTR is on, the modem is on-line. If DTR is off, the modem will not answer. To allow for auto answer with DTR down, use the AT&D0 command (Ignore DTR). The modem will then answer after S0 rings. To allow manual answer on the rise of DTR or answer with DTR high, use

AT&D2 (hang up on fall of DTR). The modem will then answer after S0 rings if DTR is up, or when DTR rises, provided it is down.

ASYNC/SYNC MODE DTR RISE

ATM2&D0

AM2&D1

DTR FALL DTR LOW

Ignore DTR.

Do not answer.

AT&M2&D2

AT&M2&D3

Ignore DTR.

Table 5.3

Ignore DTR.

On-line Command

State.

Hang up and go to

Command State.

Execute ATZ and hang up.

Mode 2 Synchronous

Do not answer.

Mode 3 Synchronous

This mode is the as the AT&M2 mode (as detailed above) except that when the modem connects it will switch to slave synchronous mode. In this mode, the Tx clock is internally connected (slaved) to the Rx clock.

Copyright (C) Dataplex Pty Ltd 5-3

APPLICATIONS

5.5 Leased Line Operation

Section 5

The DPX-213 supports leased line operation. This mode (AT&L1) follows the CCITT recommendations for V.22 and V.22bis and is useful for sync and async applications with many manufacturers products. The AT&L1 command does not support Constant Speed

Interface or MNP operation. The AT&L1 mode provides a controlled carrier mode based on the RTS interface lead (AT&K1) which can be made permanent carrier with the AT&D0 command. V.22bis modems have long equalisation and training times (2+ seconds) and are not suitable for multi-drop operation or fast polling.

This leased line configuration is fully compatible with the CCITT V.22 and V.22bis recommendations for both synchronous and asynchronous leased line operation. The modem gains synchronisation on the data stream without requiring a full V.22bis retrain sequence, making this mode compatible with other V.22bis modems such as the TEL-424.

V.22bis, V.22 and V.21 recommendations are supported in Asynchronous Leased Line

Mode with synchronous operation available at 1200 and 2400 bps. The following set-up string is provided as a guide (spaces included for clarity):

AT&F F5 &M1 &L1 S0=0 &E &I &W where

COMMAND DESCRIPTION

AT&F

&M1

Factory default to define start values.

Force 2400 bps speed.

Select Synchronous Mode.

&L1

S0=0

Leased Line mode.

Make this end originate.

No MNP/V42.

No CSI.

Write configuration.

5-4

The originate end must have S0=0 and the answer end must have S0 set to any value except zero (typically S0=1 at the answer end). To set the speed of operation enter the above set-up with the terminal set to 2400 bps. For synchronous operation, use AT&M1 or

AT&M3.

Once on-line, the unit may be returned to Command Mode by issuing an asynchronous

'pause'

+++

'pause' escape sequence. When in Command Mode, the leased line configuration can be deleted by an AT&F&W or via a Master Rest.

Section 5

5.6 Extended Character Formats

APPLICATIONS

Both MNP and AT protocols specify ten bit characters made up of one start bit, eight data bits and one stop bit. The data bits may be seven data bits and one parity bit or eight data bits with no parity bit. The V.22bis standard allows for character lengths from eight to eleven bits including start and stop bits. The DPX-213 supports 8 to 11 bit characters through the use of register S30. The Constant Speed Interface (CSI) and MNP /V42 features only support ten bit characters. Whenever eight, nine or eleven bit character support is required, MNP and CSI must be turned off.

To operate with character lengths other than ten bits, the DPX-213 must be initially configured with a 10 bit ASCII terminal, S30 needs to be set for the appropriate character length, and then the modem will switch to the extended character format at the time a connection is made. The 'pause'

+++

'pause' escape sequence must also be entered in ten bit format.

The following command string is an example of the use of this facility.

AT&M1 S30=182 N0 &Z 1234567.

This sets the modem up to dial 1234567 when DTR is raised and then pass eleven bit characters once the connection is established.

NOTE: See S30 settings in Appendix B to ensure that other bits are not corrupted unnecessarily (MNP/CSI is disabled by setting S30 bits 0,1,2 to 0).

5.7 PABX Operating Problems

The modem needs only two wires connected to the exchange to operate, tip and ring.

These are connected to Pins 2 and 6 of the Telecom 605 plug as shown in Figure 5.1.

Business PABX and other handsets such as Telecom Commander systems often have extra facilities on the handsets and non-standard wiring.

Using a modem on these circuits could cause unexpected results and possibly damage.

PABX makers follow their own design and wiring practices and it is unlikely one universal cable will ever suit all applications. If any troubles are experienced with obtaining dial tone, dialling out or receiving calls with the DPX-213, remove all extra wires from the cable, leaving only Pins 2 and 6 active, and try again. If problems still persist contact your

PABX supplier for connection information.

Figure 5.1 Telecom 604 Plug

Copyright (C) Dataplex Pty Ltd 5-5

APPLICATIONS

5.8 Low Power/Standby Mode

Section 5

The DPX-213 has a low power feature that allows the unit to be placed in a state where it will draw no current.

There are 2 methods of entering this state, namely:

• Using the ATZ1 command, or,

• Placing a value other than 0 in the inactivity timer registers S36/37, and allowing the unit to sit in offline Idle Mode until the inactivity timeout is reached.

To enter standby mode in both instances, the DTR must be disabled or held inactive. The modem will wake up on rise of DTR (if DTR is enabled), ring detection, activity on the

DTE TxD input, or power cycle.

5.9 Alarm Mode

Alternate number dialling. In alarm mode, when an alarm call is made, the unit will dial the number in location 0. If the call is unsuccessful the unit will attempt to dial the number contained in location 1. If this does not exist, the modem will revert to location 0. For every attempt (or pair of attempts if location 1 contains a number) the modem checks if the redial count (S50) has been reached and gives up if this occurs.

Alarm detection while on line. If the DTR is raised while on line or during disconnection the modem will detect the raised DTR and generate another alarm.

5.10 Password Mode

On answering a call the unit will respond with a password prompt (location 9 string) or

PASSWORD ? if location 9 is not programmed. The modem will then wait for 20 seconds and allow 3 attempts to enter a correct password. Is a correct password is seen the unit will connect (AT*P1) or disconnect and attempt to dial-back the user. If the unit is in dial back mode and a correct password is entered which does not have a dial back number, the caller will not gain access even though the modem indicates a correct password entry.

Storage locations 5-8 may be used for password storage.

Passwords are stored in the following format. For example:

\password,password\number

\fred\t2225555\jim\\sid\t5554444

\ian,sigmund,kylie\t4365879\terry\

5-6 Copyright (C) Dataplex Pty Ltd

Section 5

5.11 Remote Configuration

APPLICATIONS

In remote configuration mode, any valid AT command which does not drop the line can be issued (but without the AT prefix) to reconfigure a remote modem. Typically the command is left disabled and is temporarily enabled at the remote site by entering the escape sequence ('pause'

+++

'pause') then AT*R1 if on-line, or simply AT*R1 if off-line.

Holding down the LOOP button at the instant power is applied will also temporarily enable remote configuration.

The central site can then call in and examine S-registers with the AT*C command or reconfigure the DPX-213. The central site should execute AT*R0 before it hangs up or the remote modem should be turned off and back on again to disable the remote configuration option. Password protection (AT*P) is recommended to guard against malicious reconfiguration.

Copyright (C) Dataplex Pty Ltd 5-7

APPLICATIONS

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 5

5-8 Copyright (C) Dataplex Pty Ltd

DATA TRANSFER Section 6

6.0 DATA TRANSFER

6.1 Error Control

In synchronous applications, typically with mainframe computers, communications software running in the front end processor and terminal is responsible for error control. In asynchronous communications with mini, micro, and personal computers, there is usually no link level error control and users occasionally experience corrupted data in keyboard interactive sessions. For file transfers, most async communications packages support an error correcting protocol such as Xmodem. This protocol, and others such as Ymodem,

Zmodem and Sealink offer error correction only during the file transfer phase. Problems will still be experienced on noisy lines during the set-up phase if the link is not error protected.

MNP (Micro Networking Protocol) provides continuous error control during keyboard interactive sessions and file transfers. When these error corrected protocols are active,

ASCII file transfers are sufficient and invoking the additional error protection of Xmodem is often unnecessary and only serves to slow down file transfer.

Error Control is achieved by building packets of characters from the sending terminal, then calculating and appending a Cyclic Redundancy Check (CRC) character. This information is transmitted over the communications channel which will often have noise (electrical interference). This noise will corrupt the data and produce errors. At the receiving terminal, the packet is analysed by the same CRC algorithm and the CRC is locally computed. If the two CRCs do not match then an error has occurred and a Negative

Acknowledgment (NAK) is sent and the block is requested again. If the CRCs match, a

Positive Acknowledgment (ACK) is sent and the next block is sent. Retransmission takes place repeatedly until the block is received error free. Once the block is received error free, the next block is sent.

In simpler block-at-a-time protocols, such as Xmodem, a block is sent and then the sender pauses until an ACK or NAK is received. On satellite or long delay links this seriously reduces throughput and therefore go-back-n or sliding window protocols are preferred.

Such protocols number each block and send blocks repetitively until either the preset maximum is reached or an ACK or NAK is received from the remote modem. An ACK signal contains the number of the last successfully received block. In the event of an error, all blocks that followed the block in error are retransmitted. In very sophisticated systems,

Selective Block Retransmission sends only the block in error and the receiving device resequences the data stream before releasing it to the terminal.

The DPX-213 features extended MNP allowing selective retransmission when connected to another DPX-213 modem for higher throughput.

Copyright (C) Dataplex Pty Ltd 6-1

DATA TRANSFER

6.2 Flow Control

Section 8

Flow Control refers to the method used to stop data flow whenever the terminal or the modem needs time to retransmit blocks in error or prevent a buffer overflow. The DPX-

213 supports both RTS/CTS (Hardware or Out-of-Band) and Xon/Xoff (Software or In-

Band) flow control. Flow control is needed whenever the terminal and line speeds are different, or whenever MNP/V42 is active.

When file transfer is taking place, data flows into the DPX-213 and is sent to line in packets. When a line error occurs, the block is retransmitted. This takes a small amount of time and during this time, more data is received from the terminal and must be buffered in the modem RAM. If the line errors are substantial, or the data is continuous or faster than the line can accommodate, the modem RAM will eventually fill and either CTS is dropped, or Xoff is issued at 85% memory capacity to indicate to the terminal to stop sending while the backlog of characters in the modem are cleared. When the buffers fall to 30% full, CTS is asserted or the Xon character is sent allowing normal transfer of data to resume.

Any "error free" modem link can lose data if the terminal does not respond to Xoff quickly and over-runs the buffer, or if the modem is interrupted or loses power at either end before the data in RAM is transferred. The DPX-213 uses DC1 (11/91 HEX or ###

q

) as Xon and DC3 (13/93 HEX or ###

s

) as Xoff. Flow control (AT&Kn and AT&Un) and error control (AT&En) are separate tasks and need to be individually set within the DPX-213 according to your application needs.

6.3 Flow Control Buffers

There are eight modem buffers plus the buffers residing in your computer and terminal which must all be correctly driven or data may be lost in some conditions.

6-2

Figure 6.1 Flow Control Buffers

Referring to the figure above, buffers 1, 3, 6 and 8 are the DTE buffers controlled by the

AT&K command. Buffers 2, 4, 5 and 7 are the modem (or line side) buffers controlled by the AT&U command. If MNP/V42 is enabled and both terminals can accommodate the full data rate without issuing Xoff to the modem then flow control issues are handled for you and no data will be lost.

Section 6 DATA TRANSFER

There may be instances when the Constant Speed Interface is used without MNP/V42 and where the DTE issues Xoff (or drops RTS) to the modem. In this case, data may be lost unless AT&U is enabled.

For example, assume that the modems have Constant Speed Interface enabled

(AT&I1) and MNP/V42 disabled (AT&E0), the local terminal is set for 9600 bps with Xon/Xoff flow control and the remote terminal is set for 1200 bps with

RTS/CTS flow control. In this case, AT&U2 or AT&U3 must be used. Binary files cannot be transmitted unless Zmodem or a similar protocol is used.

Data from the local terminal (DTE A) flows into the local modem (Modem A) faster than it can be sent to line and buffer 1 will soon need to stop DTE A or data will be lost. Buffer 1 issues Xoff to DTE A by placing the Xoff character in the outbound data stream of buffer 3 and the terminal stops with no loss of data.

The data is now moved down the line from buffer 2 to buffer 5. It arrives at buffer

5 faster than buffer 6 can take it since the output speed to the terminal is only 1200 bps. Buffer 6 is in danger of an overrun and so issues Xoff to buffer 5.

Buffer 5 may now overrun and so it places an Xoff in the output stream of buffer 7 to halt the flow from the sending modem. The Xoff is received at buffer 4 and passed across to buffer 2 to halt the data flow. If AT&U3 is enabled (pass through), the Xoff character is output to buffer 3 and the DTE A. If AT&U2 is enabled (no pass through) the Xoff character is passed to buffer 2 but not output via buffer 3.

Consider another example, where both terminals operate at 4800 bps and the line speed is 2400 bps. Xon/off at the local end and RTS/CTS at the remote. The remote

DTE in this example is slow and frequently drops RTS to keep up. If AT&U0

(default) is invoked in this example, data will be lost.

In this case data flows into buffer 1 until an Xoff stops it. Data is passed to buffer 2 then to 3 and finally flows to buffer 6. The DTE has RTS low quite often and eventually buffer 6 fills. Dropping RTS at the remote end suspends output from buffer 8 causing buffers 5 and 2 to eventually overrun and lose data.

Copyright (C) Dataplex Pty Ltd 6-3

DATA TRANSFER

6.4 Microcom Networking Protocol

Section 8

MNP (Microcom Networking Protocol) is a suite of sophisticated sliding window block retransmission error control and data compression protocols. The DPX-213 has MNP to level 5 with enhanced throughput from selective block retransmission in the event of an error. This protocol offers excellent error control and achieves data throughput up to 4800 bps on good lines and 2400 bps with zero errors on noisy lines. An internal 8k buffer handles short term data overruns and either RTS/CTS or Xon/Xoff flow control ensures no data is lost.

The MNP protocol starts with a short negotiation sequence at the beginning of transmission where both modems decide on the highest level of error correction they both support. This negotiation can take several seconds (approximately 5 seconds) therefore, if your modem appears to hang after raising the CD signal, and before sending the

CONNECT message, it may be attempting to negotiate an error corrected link with the remote modem. If no MNP support is found, the DPX-213 either hangs up or enters the transparent data mode where data is transparently passed with no error correction or compression enabled.

When a 2400 bps phone line rate connection is established at MNP, the DPX-213 issues the message "CONNECT 2400/REL".

If one end of the link has MNP turned off (or does not support it) and the other does, the non MNP end will receive the MNP negotiation packets and display them as garbage on the screen. These packets, or patterns, may in some circumstances, lock up the answering device and make the link appear inoperative.

When using a DPX-213 at both ends of the link, it is recommended you set your asynchronous terminal to 9600 bps and invoke Constant Speed Interface (AT&I1, AT&E1, and AT*E1). Since there is the possibility of re-transmissions taking place to correct line errors, you must enable some form of flow control, either RTS/CTS or Xon/Xoff (default) flow control. Either RTS/CTS or Xon/Xoff flow control may be activated by the software you are using.

6-4

A minimal error protection file transfer method should be used when uploading (sending) or downloading (receiving) files. With MNP enabled, the modem link is error protected and overlaying another error control mechanism can only add delay and reduce throughput.

Section 6

6.5 Error Free or Not at All

DATA TRANSFER

In some applications you may need to be sure you connect with error control invoked. It may be desirable not to connect at all if you cannot establish a reliable link. Setting AT&E1 and AT&I0 achieves this. If the remote modem cannot support MNP, the DPX-213 will terminate the call immediately after the MNP negotiation sequence.

If AT&E1 and AT&I1 are set, the DPX-213 will negotiate with the remote modem for the highest level of MNP that both support and if no MNP support is found, the modem will enter the Transparent Data Mode and remain on-line.

6.6 Constant Speed Interface

A Constant Speed Interface on the DPX-213 can be invoked to ensure your terminal always functions at the same speed, regardless of the line speed the modem connects at.

If you want the interface speed to change with each different line speed, use the AT&I0 command. For example, with AT&I0 set, if you have your terminal set at 4800 bps then call a 1200 bps modem, the DPX-213 will issue the message "CONNECT 1200" at the initial bit rate of 4800 bps and then immediately switch to 1200 bps for the remainder of the call. To make any sense of the data you must quickly change your terminal speed to

1200 bps.

Some software packages, such as Telix, can read the CONNECT (speed) message and automatically adjust the PC com ports while in other packages you must manually reset the

PC com port speed. If the interface constant speed rate is set at 4800 bps for example, the

"CONNECT 2400" message could incorrectly instruct your software into changing the terminal speed to 2400 bps when the correct speed is 4800 bps. We recommend the use of the Constant Speed Interface provided your terminal can employ either hardware of software flow control.

6.7 File Transfer Restrictions

File transfer restrictions exist when using Xon/Xoff flow control. For example, when transferring pure binary files, where the data bytes in the file may be any combination of 8 bits, there is a possibility there will be some stray Xon or Xoff characters. If Xon/off flow control (AT&K1) or AT&U1,2 or 3 is enabled, any stray Xoff characters will command the

DPX-213 to stop sending data.

For such applications, the DPX-213 should be set to RTS/CTS flow control with the

AT&K2 command. This command will work for text or binary files provided your communications software correctly drives RTS and respond to CTS. MNP still works with binary files and ignore any embedded Xon/Xoff characters. Alternatively, a file transfer program such as Zmodem (that removes the Xon/Xoff characters at the sending end and adds them back at the receiving end) is required.

Copyright (C) Dataplex Pty Ltd 6-5

DATA TRANSFER Section 8

The ZMODEM or Ymodem-G protocol is ideal for all types of file transfer over an error protected channel. ZMODEM is a "sliding window" protocol that allows for long path delays such as through multiplexer channels, packet switched networks or ARQ modems.

ZMODEM searches for control characters such as Xon and Xoff which may be embedded in the file. Such characters are converted to an escape sequence which will not confuse the

MNP flow control. ZMODEM with either RTS/CTS or Xon/Xoff flow control allows

*.EXE, *.BIN, *.COM and all other files to be sent over the DPX-213 while retaining the benefits of error correction. ZMODEM is error protected so there is a small additional overhead, but it is a very efficient protocol compared to XMODEM.

•

6.8 Software Compatibility

The DPX-213 modem operation is compatible with most popular communication programs that use the AT dialling protocol. When the modem is using MNP, there are some software restrictions described above which must be understood. Zmodem or Ymodem-G is recommended for file transfers whenever MNP or V42 is active. The use of small block, half duplex protocols such as Xmodem will slow down file transfers considerably and not take full advantage of the in built error control.

The DPX-213 modem is compatible with all communications programs that use the 'AT' dialling protocol. Listed below is an incomplete list of the software tested with the DPX-

213. Consult Dataplex for more specific details.

Smartcom Version 2.1;

Magicsoft MTEZ;

Crosstalk XVI Version 3.6;

Procomm Version 3.2;

Supercomm Version 2 & 3;

PCTalk;

Telix (Versions 2 & 3);

Dataplex FleetCom, and,

Mirror II.

6-6 Copyright (C) Dataplex Pty Ltd

Section 7

7.0 TESTING AND DIAGNOSTICS

TESTING and DIAGNOSTICS

Dataplex have designed the DPX-213 to provide years of trouble free service. However, abuse, component failure or external high voltages will damage the unit. All Dataplex products are subjected to 72 hour burn-in and extensive testing before leaving the factory to ensure professional quality and reliability.

The DPX-213 uses professional grade components and includes the minimum number of mechanical components which can degrade with age. There are no customer maintainable components in the DPX-213.

In the event of a confirmed hardware failure the purchaser must return the modem to a

Dataplex authorised service center, after first obtaining a Return to Manufacturer

Authorisation (RMA) number.

The DPX-213 has facilities for enabling remote and local loops for modem and line testing.

NOTE: If bit error rate tests are performed with MNP enabled, line errors will be corrected but a false bit error rate reading will be given. The Constant Speed

Interface allows test equipment to run faster or slower than the line can accommodate and either data will be lost or flow control characters may appear as errors during a bit error rate test. Always ensure MNP is disabled and the test equipment is running at the true line rate when performing any tests.

7.1 Operator Initiated Tests

Operator initiated tests cover local and remote loopback tests. Testing a remote modem assumes that the local modem is fully CCITT V.22bis compliant or is another DPX-213.

Whenever a local or remote test is in progress, the OH LED will be flashing. Tests initiated with the AT&Tn commands are:

AT&T0 - Terminate test in progress.

AT&T1 - Initiate Local Analogue Loopback (LALB).

AT&T4 - Enable Remote Digital Loopback (RDLB) response.

AT&T5 - Disable Remote Digital Loopback (RDLB) response.

AT&T6 - Initiate Remote Digital Loopback (RDLB).

Tests AT&T1 and AT&T6 execute until the user enters the AT&T0 command or the power is disconnected.

Copyright (C) Dataplex Pty Ltd 7-1

TESTING and DIAGNOSTICS

7.2 Local Analog Loopback (ALB)

Section 7

Local Analog Loopback will test the analog and digital performance of the DPX-213 modem up to the line interface hybrid. Analog Loopback is controlled with the AT&T1 command.

If the DPX-213 is configured for switched network operation, the modem must be off-line for this test to work properly. If you are on-line the modem will not go into loop but will issue "CONNECT 2400" and revert to the On-line Data Mode (equivalent to typing ATO).

To enter the Analog Loopback, type the command string

at&t1K

In synchronous or asynchronous operation, the modem will respond with an asynchronous

"LOOP GRANTED" message. All characters from your keyboard will be echoed back to you. To disable the messages in synchronous Mode, use the ATQ1 command. Exit the test by typing the 'pause'

+++

'pause' escape sequence then AT&T0.

Figure 7.1 Local Analog Loopback

7.3 Remote Loopback Response

When power is applied, Remote Loopback is disabled. Therefore, your modem cannot be put into loop from the remote end nor can the command AT&T6 be issued locally.

To enable Remote Loopback, type the command string

at&t4K

AT&T5 or AT&F disables Remote Loopback.

7-2 Copyright (C) Dataplex Pty Ltd

Section 7

7.4 Remote Digital Loopback (RDLB)

TESTING and DIAGNOSTICS

This test will verify the receive and transmit sections of both DPX-213 modems and the phone line in both switched network and leased line operation.

The Remote Digital Loopback test is initiated by typing the escape sequence followed by the command

at&t6K

In asynchronous modes, you will now get one of two messages on your screen: "LOOP

GRANTED" if the remote modem is able to support loopback testing or "RDL DENIED" if the remote modem either cannot support RDLB or has previously issued the AT&T5 command.

The DPX-213 modem which is in RDL mode will display "RDL ACCEPTED" if an RDL request has been received or one or more "RDL DENIED" messages if an RDL request was received but AT&T5 was set.

During loops, the OH LED will flash. Once the loop is established, all data sent by the local DPX-213 will be echoed by remote modem and appear on your terminal.

Exit the test by issuing

+++

escape sequence then entering

at&t0K

Return to the data state with the ATO command.

Figure 7.2 Remote Digital Loopback

7-3

TESTING and DIAGNOSTICS

PAGE INTENTIONALLY LEFT BLANK .

Section 7

7-4 Copyright (C) Dataplex Pty Ltd

S REGISTERS Section 8

8.0 S REGISTERS

The "S" registers, or status registers store the modem configuration parameters. The S registers (particularly the bit mapped registers) are usually only altered using the AT commands, but in exceptional circumstances may require alteration via the ATSr=n command. S registers should be altered with care, as it is possible to configure the modem with conflicting parameters producing unpredictable results. Should altering the S registers produce erratic operation, reload the factory default settings using the AT&F command.

The DPX-213 uses 24 "S" registers.

This Section contains information on the bit mapped registers used in the DPX-213. These registers are set and reset by the various AT commands.

To change the contents of a bit-mapped register, you must change the appropriate bits, recalculate the decimal value to reflect those changes and then set to the new value to initiate the changes. Changing a bit-mapped S-Register involves the following steps:

1. The binary notation system is used in the following example. A simple system for

converting 8 bit binary representations into their decimal equivalents is given

here. In order to perform the following steps, you will need a copy of the table

given below.

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 BIT:

Current Setting :

New Setting : TOTAL

Decimal Equivalent

Underline for bits set to '1'

128 64 32 16 8 4 2 1

Table 8.1 Table for Converting 8 Bit Binary to Decimals

2. Use the ATSr? command to display the particular S-register value you wish to

change (where r equals the S-reg value you wish to display between 0 and 34).

3. From the display, determine the corresponding 8 bit representation. Insert the bit

values in the row 'Current Setting' using the table given above.

4. Determine those bits you need to change by changing the bit values as

appropriate. To achieve this, you will need to refer to the appropriate S-register

description. Insert the new bit values in the row 'New Setting' using the table

given above. The new binary number should include those bit values which have

not changed.

Copyright (C) Dataplex Pty Ltd 8-1

S REGISTERS Section 8

5. Wherever a '1' appears in the 'New Setting' row, perform the conversion by

underlining the decimal equivalent for that particular bit value and then

ADDING together the underlined decimal numbers. Place this result in the

TOTAL cell.

6. You can now change the contents of the S-register by assigning the derived

TOTAL decimal value to the S-register. This is performed by the ATSr=n

command, where r equals the S-reg value you have changed (between 0 and 50)

and n equals the new decimal value (between 0 and 255).

For example, to change the value of Register S30 such that MNP 2-4 error control and

MNP 2-5 data compression is enabled and the Constant Speed Interface is disabled, you would do the following:

1. Display the current setting of the bit register by entering

ats30?K

2. In the factory default condition, the contents of S30 will read 10111100 in

binary format and 243 in decimal format {BC HEX}. Refer to the appropriate

page of this Section for a description of each bit value for S30. To enable Error

Control and Data Compression and disable Constant Speed Interface, you need to

change bit 0, 1 and 2 respectively.

Using the steps outlined previously would yield the following table:

BIT:

Current Setting :

New Setting :

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Decimal equivalent if bit set to 1 (0 otherwise)

128 64 32 16 8

TOTAL

187

3. Finally, to assign the new decimal value to the register contents you would type

ats30=187K

. The changes are now in affect.

8-2 Copyright (C) Dataplex Pty Ltd

Section 8

S0

Default

Range

Rings to Answer

: 2 (Answer on second ring)

: 0 to 255 (Stored in NVRAM)

S REGISTERS

Establishes the number of rings that the modem must receive before the auto answer sequence is started. Values of 0 ensure the DPX-213 never answers (the value for

Originate Mode) while values from 1-255 will enable auto answer.

NOTE: When in leased line Mode, S0=0 forces the DPX-213 into Originate Mode and

S0=(1-255 but not zero) forces the DPX-213 into Answer Mode. For a point to

point leased line application, you must set ATS0=0 at one end and ATS0=1 to

255 at the other end; n must NOT be 0 at both ends.

S1

Default

Range

Ring Count

: 0

: 0 to 255

S1 is a read only register that is incremented every time an incoming ring signal is detected. This register is automatically cleared if no ring is received within an 8 second interval.

S2

Default

Escape Code Character

: 43 Decimal (

+

; {2B HEX})

: 0-255 Range

S2 contains the ASCII value of the escape code character. The escape code allows the user to exit the on-line state and return to local command state.

S3

Default

Carriage Return Character

: 13 Decimal (###

m

; {0D HEX})

: 0-255 Range

S3 contains the ASCII value of the Carriage Return character. This character serves as the command line terminator.

S4

Default

Line Feed Character

: 10 Decimal (###

j

; {0A HEX})

: 0-255 Range

S4 contains the ASCII value of the Line Feed character. The Line Feed character is output after the Carriage Return character if full word (verbose) results are enabled (ATV1 command).

Copyright (C) Dataplex Pty Ltd 8-3

S REGISTERS

S5

Default

Back Space Character

: 8 Decimal (###

h

; {08 HEX})

: 0-255

Section 8

Range

S5 contains the ASCII value of the Back Space character. When a character matching the

Back Space character is received any time during a command entry, the modem performs the following :

1. The Back Space Character is echoed.

2. A Forward Space {20 HEX} is output to the DTE.

3. Another Back Space Character is output to the DTE.

If the user tries to backspace past the attention code ('AT') the modem will ignore the backspace characters.

S6

Default

Range

Wait for Dial Tone

: 2 Decimal

: 2 to 255 Seconds (Stored in NVRAM)

S6 contains the time (in seconds) that the DPX-213 will wait before dialling a phone number. This delay allows for the delay in dial tone after going off-hook. S6 will be ignored if ATX3 or ATX4 is enabled. If S6 is set to a value less than 2 seconds the DPX-

213 will ignore the value and wait a minimum of 2 seconds.

S7

Default

Range

Wait for Carrier after Dial

: 45 Decimal

: 0 to 255 Seconds (Stored in NVRAM)

S7 contains the time (in seconds) that the DPX-213 will wait for carrier after dialling is completed. In the answer mode S7 is the time that the modem waits for carrier after sending answer tone.

S8

Default

Range

Dial Pause Time

: 2 Decimal

: 0 to 255 Seconds (Stored in NVRAM)

S8 contains the time (in seconds) that the DPX-213 will wait when a comma is encountered in the dial string. This feature is used to insert a pause during dialling to allow for PABX exchange delays.

8-4 Copyright (C) Dataplex Pty Ltd

Section 8

S10

Default

Range

Carrier Loss Response Time

: 40 Decimal (0.04 Seconds)

: 0 to 255 (in 0.02 Second increments, Stored in NVRAM)

S REGISTERS

S10 establishes the delay between loss of carrier to the time that the DPX-213 disconnects.

By increasing this time, the modem will become less susceptible to line dropouts. By setting register S10 to 255 the DPX-213 will ignore the carrier status and function as if carrier were always present.

S12

Default

Range

Escape Code Guard Time

: 50 Decimal (1 Second)

: 0 to 255 (Stored in NVRAM)

S12 contains the value (in 20 millisecond intervals) of the Escape code guard time. The escape code guard time is the time that the modem must see steady MARK (idle, no key strokes) before and after the escape code sequence before the sequence is recognized. It is also the maximum amount of time that the escape code characters can be spaced apart. If the escape guard time = 0, the '

+++

' feature is disabled.

S14

Default

Range

Echo, Quiet, Leased Line and Dialling

: 14 Hex

: 0 to 255 (Stored in NVRAM)

S14 contains a bit map of certain internal states of the modem. This register is a read only register and writing to this register may cause unpredictable results.

BIT

1 0

VALUE(S) AT

COMMAND

0 0

0 1

1 0

1 1

AT&D0

AT&D1

AT&D2

AT&D3

ATE0

ATE1

ATQ0

ATQ1

ATV0

ATV1

AT&L0

AT&L1

ATDT

ATDP

Not Used

DESCRIPTION

Ignore DTR input.

On DTR fall enter On-line Command.

On DTR fall hang up call.

On DTR fall initialize modem.

No command echo.

Command echo.

Result code enabled.

Result code disabled.

Numeric result codes.

Verbose result codes.

Dial network.

Leased line mode.

Tone dial default.

Pulse dial default.

NZ dialling (enables N+1 dialling).

Copyright (C) Dataplex Pty Ltd 8-5

S REGISTERS

S21

Section 8

Default

Range

: 0

: 0 to 255 (Stored in NVRAM)

This register is read only and writing to this register may cause unpredictable results.

BIT

2 1

4 3

6 5

DTR Control, Dumb Mode, Alarm Mode, Password

1 0

1 1

0 0

0 1

1 0

1 1

0 0

0 1

1 0

VALUE(S) AT

COMMAND

0 0

0 1

AT&C0

AT&C1

AT*D0

AT*D1

AT*D2

AT*D3

AT*A0

AT*A1

AT*A2

AT*A3

AT*P0

AT*P1

AT*P2

AT*R0

AT*R1

DESCRIPTION

CD always asserted.

CD follows line carrier.

Disable dumb mode.

Ignore AT commands.

Ignore abort options.

Ignore AT and abort key operations.

Alarm mode disabled.

Full alarm mode enabled.

Partial alarm mode enabled.

Reserved.

Password security disabled.

Password security enabled.

Password with dialback.

Remote configuration disabled.

Remote configuration enabled.

S23

Default

Range:

Modulation,CCITT\Bell,Parity,Guard Tone,Calling Tone

: 18 Hex

: 0 to 255 (Stored in NVRAM)

This register is read only and writing to this register may cause unpredictable results.

BIT

2 1 0

5 4

VALUE(S) AT

COMMAND

0 0 0 ATF0

0 0 1

0 1 0

0 1 1

1 0 0

ATF1

ATF2

ATF3

ATF4

1 0 1

0 0

0 1

1 0

1 1

ATF5

ATB0

ATB1

Not Applicable

DESCRIPTION

Line speed set by terminal speed.

300 bps.

Not used.

V.22 or Bell 212A 1200 bps.

V.22bis 2400 bps.

Disable Bell Mode.

Enable Bell Mode.

Even parity.

Space parity.

Odd parity.

Mark parity.

AT&G0

AT&G1

AT*G0

AT*G1

No Guard tone.

Guard tone enabled.

No calling tone.

Calling tone enabled.

8-6 Copyright (C) Dataplex Pty Ltd

Section 8

S30

Default

Range

BIT

S REGISTERS

MNP, CSI, Result Codes, Pulse Ratio, Character Size

: BC Hex

: 0 to 255 (Stored in NVRAM)

4 3

7 6

0 0

0 1

1 0

1 1

VALUE(S) AT

COMMAND

0 0

0 1

1 0

1 1

AT&E0

AT&E1

AT*E0

AT*E1

AT&I0

AT&I1

ATX0

ATX1

ATX2

ATX3

AT&P0

AT&P1

DESCRIPTION

MNP 2-4 error control disabled.

MNP 2-4 error control enabled.

MNP 2-5 compression disabled.

MNP 2-5 compression enabled.

Disable Constant Speed Interface.

Enable Constant Speed Interface.

Result code settings.

U.S.A. pulse dial make ratio.

CCITT ratio.

Not Applicable 8 bit character length.

9 bit character length.

10 bit character length.

11 bit character length.

S31

Default

Range

Flow Control, Pass Through, Break Handling,

Sync\Async and Remote Loop Disable

: 01 hex

: 0 to 255 (Stored in NVRAM)

BIT

1 0

3 2

6 5

0 0

0 1

1 0

1 1

VALUE(S) AT

COMMAND

0 0

0 1

AT&K0

AT&K1

1 0

1 1

0 0

0 1

AT&K2

AT&K3

AT&U0

AT&U1

1 0

1 1

AT&U2

AT&U3

AT*Y0

AT*Y1

AT&M0

AT&M1

AT&M2

AT&M3

AT&T5

AT&T4

DESCRIPTION

Disable flow control.

Enable Xon/Xoff flow control.

Enable RTS/CTS flow control.

Enable both.

Pass through OFF, modem flow OFF.

Pass through ON, modem flow OFF.

Pass through OFF, modem flow ON.

Pass through ON, modem flow ON.

Expedited/non destructive.

Expedited/destructive.

Async mode normal.

Async dial stored number.

Async dial sync connect.

Async dial slave sync connect.

Disable remote loops.

Enable remote loops.

8-7

S REGISTERS

S32 Modem Flow Control Xoff Character

Default : 19 decimal (###

s

13 HEX)

Range : 0 to 255 (Stored in NVRAM)

Stores the ASCII 8-bit value of the modem (AT&K) flow control X-off character.

Section 8

8-8

S33 Modem Flow Control Xon Character

Default : 17 decimal (###

q

- 11 HEX)

Range : 0 to 255 (Stored in NVRAM)

Stores the ASCII 8-bit value of the modem (AT&K) flow control X-on character.

S36 &

S37 Inactivity Timer Duration

Default

Range

: 0 Decimal

: 0 to 65535 Seconds (Stored in NVRAM)

This register pair (high byte and low byte) contain the timer duration for line or DTE inactivity. The value placed in these S registers is used to determine if the modem has been inactive for a given period of time and subsequently causes the modem to disconnect the call. To calculate registers S36 and S37, use the following equations:

S37 = (Inactivity Timer Duration divided by 256) - Whole Number Only

S36 = Remainder of above equation.

For example, setting the inactivity timer duration to 1 minute and 30 seconds (or 90 seconds) would involve setting register S37 to 0 (as 90 divided by 256 yields 0) and setting register S36 to 90 (as the remainder of the previous equation is 90). In other words, when the duration of the inactivity timer is less than 256 then S37 will be 0 and S36 will be the duration. Alternatively, setting the inactivity timer duration to 5 minutes (300 seconds) would involve setting register S37 to 1 (as 300 divided by 256 yields 1) and setting register

S36 to 44 (as the remainder of the previous equation is 44). In other words, when the duration of the inactivity timer is greater than 256, then S37 will store the multiples of 256 and S36 the remainder.

If the inactivity timer is employed, the modem will attempt to go into the low power/standby mode (provided the modem is left off-line in the command state for greater than the inactivity period). The actual time in seconds is ((256 x S-Register S37) + S-

Section 8 S REGISTERS

S50 Redial Attempts

Default

Range

: 5 Decimal

: 0 to 256 Seconds (Stored in NVRAM)

If a call is made in AT*A mode and the message is not successfully sent, the unit will attempt to redial the number of times stored in this register before giving up. This takes into account alternate number dialling. In this scenario, the modem attempts to connect using the number stored in location 0 and then the number stored in location 1 on failure to send an alarm message. For example, if alternate numbers are provided and S50 is set to four then both numbers will be dialed four times before the units stops. If S50 is set to zero unit will attempt to dial indefinitely and S51 should be set to 3 to comply with Austel

Permit.

S51 Delay Before Redialling

Default

Range

: 3

: 1 to 256 Seconds (One minute increments)

If the unit is attempting to dial after dropping a previously raised telephone line, the unit will wait for a interval of S51mins before raising the line again and attempting to dial. If no alternate number is provided then the unit will wait 2*S51 minutes before redialling.

Attempting to set this value to 0 will result in a default delay of 3 minutes. To comply with

Austel Permit the unit should not be allowed to dial more than 10 times in 30 minutes. It is recommended that this register should not be changed from the default value.

S52

Default

Delay Before Alarm Message

: 0

Range : 0 to 256 Seconds (Increments of 100mS)

This register provides control of the delay before the modem outputs an alarm message to line. This value in only valid in Constant Speed Interface mode as in MNP modes the modem monitors the MNP level activity to guarantee reception of the message by the called party.

S53

Default

MNP Autoreliable Delay

: 0

Range : 0 to 256 Seconds (One second increments)

This delay is the period that the modem will attempt to provide an MNP connection before dropping through to Constant Speed Interface or Disconnecting. When set to 0 then modem will use a standard 8 second period.

Copyright (C) Dataplex Pty Ltd 8-9

S REGISTERS

T HIS PAGE INTENTIONALLY LEFT BLANK .

Section 8

8-10 Copyright (C) Dataplex Pty Ltd

Section 9 TECHNICAL SPECIFICATIONS

9.0 TECHNICAL SPECIFICATIONS

The DPX-213 is a multi standard modem, with high reliability and low power consumption. The modem features an extended AT command set, error correction, data compression, pulse and tone dialling, automatic adaptive equalisation, synchronous and asynchronous capability, leased line and dial network support and numerous other features.

Compatibility & Modulation 2400 bps QAM - CCITT V.22bis.

1200 bps DPSK - CCITT V.22, and Bell 212A.

300 bps FSK - CCITT V.21, and Bell 103.

Data Format Asynchronous - 8-11 bit character format including parity and stop bit.

Synchronous - serial, binary, bit synchronous; protocol independent.

Interface Speeds

Line Speeds

Asynchronous 300, 1200, 2400, 4800, 9600.

Synchronous 1200 and 2400 bps.

Asynchronous 300, 1200, 2400 bps.

Synchronous 1200, 2400 bps.

Operation

Equalisation

Full duplex over two wire switched and leased lines.

Automatic or manual originate and answer.

Auto-adaptive equaliser.

Transmit Timing

Transmit Level

Internal or external +.01%, loop timing.

-10dBm.

Guard Tone Frequency

Loss of Carrier Disconnect 0.04 Seconds (Programmable).

Answer Tone Frequency

550 Hz, 1800 Hz, or none.

CCITT 2100Hz, Bell 2135 Hz.

Receiver Dynamic Range

Carrier Detect

Hysteresis

Ring Detection

-6 dBm to -45 dBm.

ON at -43 dBm.

OFF at -48 dBm.

Greater than 2dB.

Level = 35 to 150 V RMS.

Frequency = 13 to 55 Hz.

DTE Interface

VF Interface

Power Requirements

CCITT V.24/V.28; EIA RS-232-C, DB-25-S (female).

RJ-11 jack with mode 3 wiring.

7.5 - 18VDC 600mW.

Copyright (C) Dataplex Pty Ltd 9-1

TECHNICAL SPECIFICATIONS

Environmental

Physical

Temperature 0 to 85 degrees C.

Relative humidity < 95%, non-condensing.

Height - 20 mm.

Width - 127.8 mm.

Depth - 130 mm.

Weight - 0.6 kg.

MODELS AVAILABLE

DPX-213-01 240VAC Standard Mains Operation

DPX-213-02

DPX-213-03

7-20VDC Standard DC Operation

20-70VDC Standard DC Operation

Standard Accessories Supplied

Four wire VF line cord RJ-11 to Telecom 605 plug

Optional or Replacement Items

023-0008-1 RS232C Data Cable

023-0091-2 Adapter, RJ-11 to Telecom 610

Section 9

9-2 Copyright (C) Dataplex Pty Ltd

Section 10

10.0 WARRANTY AND REPAIRS

WARRANTY and REPAIRS

Dataplex warrants the DPX-213 to be free from defective materials or workmanship for a period of 3 months from the date of purchase. This warranty is extended to 12 months from date of purchase for users who return the warranty registration card within 30 days from the date of purchase. This warranty does cover equipment damaged by accident, abuse, unauthorised modifications, or improper use. When subjected to normal, proper and intended usage, Dataplex agrees to repair or replace, at their option, any defective material without cost, provided:

1. You promptly notify Dataplex of any defect.

2. You return the equipment, freight prepaid, to the Dataplex office that you

purchased the equipment from.

3. Dataplex's inspection of the equipment shows that any defect was not caused by

accident, misuse, negligence, alteration, improper installation, unauthorised

repair or improper testing.

Dataplex will return the equipment, freight prepaid, after repair or replacement within a reasonable time.

Dataplex shall not be responsible or liable for any consequential damages or loss of profits which may arise as a result of any defect in its products during use.

Dataplex warrants all repairs and upgrades performed at its factory for 90 days after completion unless an off-site repair maintenance agreement is .

Out of warranty repairs will be performed at ruling time and materials rates. Before returning any equipment, you must phone Dataplex Pty. Ltd. and obtain a Return Material

Authorisation (RMA) number from Customer Service.

All returns must be shipped freight prepaid. Check the latest telephone directory for the number of your local Dataplex Customer Service center.

Dataplex Pty Ltd.

PO BOX 901

L 2, 71 Epping Rd ,

NORTH RYDE , NSW, 2 113 AUSTRALIA

DPX: (02) 9869 2500

FAX: (02) 9869 2600

Copyright (C) Dataplex Pty Ltd 10-1

WARRANTY and REPAIRS Section 10

INSTALLATION and SERVICE RECORD

Equipment : Dataplex DPX-213 Modem

Serial No. : _____________________

Revision. : _____________________

Purchase Date : _____________________

Contract No. : _____________________

Renewal Date(s) : _____________________

Service Contact : _____________________ Phone : (02) 9869 2500

[head office]

Service History:

____________________________________________________________

Notes:

____________________________________________________________

10-2 Copyright (C) Dataplex Pty Ltd

PROBLEM REPORT SHEET Appendix A

PROBLEM REPORT SHEET

Use this form to list any problems which you find in the modem, then mail or fax it to Dataplex

Fax No. (02) 9869 2500.

SOFTWARE REVISION NO.: __________________ (USE ATI3 TO FIND OUT)

MODEL NO.: DPX-213 DATE OF PURCHASE: ____________

SERIAL NO.: ______________________

PROBLEM/BUG:

_________________________________________________________________

'AT' CONFIGURATION USED BY MODEM

(USE AT*C and print screen dump TO FIND OUT):

_________________________________________________________________

USER IDENTIFICATION:______________________

NAME: ___________________________________________________________

DEPARTMENT/TITLE: ______________________________________________

COMPANY: _______________________________________________________

ADDRESS: ________________________________________________________

__________________________________________ P/CODE: _______________

TELEPHONE (_____) ______________________ DATE: __________________

THANK YOU FOR YOUR HELP

PRODUCT MANAGER DPX-213

DATAPLEX Pty Ltd

Copyright (C) Dataplex Pty Ltd A-1

Appendix B S REGISTER SUMMARY

S REGISTER SUMMARY

Register

S10

S12

S14

S21

S23

S30

S31

S32

S33

S36,37

S50

S51

S52

S53

Brief Description Defaults (Decimal unless stated)

2 ® Rings to answer.

Ring count.

® Escape code character.

® Carriage return character.

® Line feed character.

® Back space character.

® Wait for dial tone.

® Wait for carrier after dial.

® Dial pause time for comma.

® Loss of carrier response time.

® Escape code guard time.

® Echo response codes verbose leased line dialling. 14 Hex

® CD control, dumb alarm mode, password, remote configuration.

® Modulation, parity, guard tone, calling tone.

® MNP, CSI, result codes, make/break

18 Hex

08 Hex

® Flow control, break, pass through, remote loop. 01 Hex

19 ® Xoff character.

® Xon character.

® Inactivity duration.

® Redial attempts.

® Delay before redialling.

® Delay before alarm message.

® MNP autoreliable delay.

NOTE:

®

indicates the S-register contents are stored in non-volatile memory.

B-1 Copyright (C) Dataplex Pty Ltd

Appendix B

T HIS PAGE INTENTIONALLY LEFT BLANK .

S REGISTER SUMMARY

Copyright (C) Dataplex Pty Ltd B-2

Appendix C ASCII CONVERSION TABLE

ASCII CONVERSION TABLE

KEY: DEC BINARY

HEX ASCII/CTRL

Please Note: ASCII or character equivalents are given only for the first 127 entries (as ASCII is a

7 bit code). Also, control (Cntrl) sequences exist for the first 32 entries only.

0 00000000 16 00010000 32 00100000 48 00110000 64 01000000 80 01010000 96 01100000 112 01110000

00 NUL ^@ 10 DLE ^P 20 SPACE 30 0 40 @ 50 P 60 ` 70 p

1 00000001 17 00010001 33 00100001 49 00110001 65 01000001 81 01010001 97 01100001 113 01110001

01 SOH ^A 11 DC1 ^Q 21 ! 31 1 41 A 51 Q 61 a 71 q

2 00000010 18 00010010 34 00100010 50 00110010 66 01000010 82 01010010 98 01100010 114 01110010

02 STX ^B 12 DC2 ^R 22 " 32 2 42 B 52 R 62 b 72 r

3 00000011 19 00010011 35 00100011 51 00110011 67 01000011 83 01010011 99 01100011 115 01110011

03 ETX ^C 13 DC3 ^S 23 # 33 3 43 C 53 S 63 c 73 s

4 00000100 20 00010100 36 00100100 52 00110100 68 01000100 84 01010100 100 01100100 116 01110100

04 EOT ^D 14 DC4 ^T 24 $ 34 4 44 D 54 T 64 d 74 t

5 00000101 21 00010101 37 00100101 53 00110101 69 01000101 85 01010101 101 01100101 117 01110101

05 ENE ^E 15 NAK ^U 25 % 35 5 45 E 55 U 65 e 75 u

6 00000110 22 00010110 38 00100110 54 00110110 70 01000110 86 01010110 102 01100110 118 01110110

06 ACK ^F 16 SYN ^V 26 & 36 6 46 F 56 V 66 f 76 v

7 00000111 23 00010111 39 00100111 55 00110111 71 01000111 87 01010111 103 01100111 119 01110111

07 BEL ^G 17 ETB ^W 27 ' 37 7 47 G 57 W 67 g 77 w

8 00001000 24 00011000 40 00101000 56 00111000 72 01001000 88 01011000 104 01101000 120 01111000

08 BS ^H 18 CAN ^X 28 ( 38 8 48 H 58 X 68 h 78 x

9 00001001 25 00011001 41 00101001 57 00111001 73 01001001 89 01011001 105 01101001 121 01111001

09 HT ^I 19 EM ^Y 29 ) 39 9 49 I 59 Y 69 i 79 y

10 00001010 26 00011010 42 00101010 58 00111010 74 01001010 90 01011010 106 01101010 122 01111010

0A LF ^J 1A SUB ^Z 2A * 3A : 4A J 5A Z 6A j 7A z

11 00001011 27 00011011 43 00101011 59 00111011 75 01001011 91 01011011 107 01101011 123 01111011

0B VT ^K 1B ESC ^[ 2B + 3B ; 4B K 5B [ 6B k 7B {

12 00001100 28 00011100 44 00101100 60 00111100 76 01001100 92 01011100 108 01101100 124 01111100

0C FF ^L 1C FS ^\ 2C , 3C < 4C L 5C \ 6C l 7C |

13 00001101 29 00011101 45 00101101 61 00111101 77 01001101 93 01011101 109 01101101 125 01111101

0D CR ^M 1D GS ^] 2D - 3D = 4D M 5D ] 6D m 7D }

14 00001110 30 00011110 46 00101110 62 00111110 78 01001110 94 01011110 110 01101110 126 01111110

0E SO ^N 1E RS ^^ 2E . 3E > 4E N 5E ^ 6E n 7E ~

15 00001111 31 00011111 47 00101111 63 00111111 79 01001111 95 01011111 111 01101111 127 01111111

0F SI ^O 1F US ^- 2F / 3F ? 4F O 5F _ 6F o 7F DEL

C-1 Copyright (C) Dataplex Pty Ltd

ASCII CONVERSION TABLE Appendix C

ASCII CONVERSION TABLE

128 10000000 144 10010000 160 10100000 176 10110000 192 11000000 208 11010000 224 11100000 240 11110000

80 90 A0 B0 C0 D0 E0 F0

129 10000001 145 10010001 161 10100001 177 10110001 193 11000001 209 11010001 225 11100001 241 11110001

81 91 A1 B1 C1 D1 E1 F1

130 10000010 146 10010010 162 10100010 178 10110010 194 11000010 210 11010010 226 11100010 242 11110010

82 92 A2 B2 C2 D2 E2 F2

131 10000011 147 10010011 163 10100011 179 10110011 195 11000011 211 11010011 227 11100011 243 11110011

83 93 A3 B3 C3 D3 E3 F3

132 10000100 148 10010100 164 10100100 180 10110100 196 11000100 212 11010100 228 11100100 244 11110100

84 94 A4 B4 C4 D4 E4 F4

133 10000101 149 10010101 165 10100101 181 10110101 197 11000101 213 11010101 229 11100101 245 11110101

85 95 A5 B5 C5 D5 E5 F5

134 10000110 150 10010110 166 10100110 182 10110110 198 11000110 214 11010110 230 11100110 246 11110110

86 96 A6 B6 C6 D6 E6 F6

135 10000111 151 10010111 167 10100111 183 10110111 199 11000111 215 11010111 231 11100111 247 11110111

87 97 A7 B7 C7 D7 E7 F7

136 10001000 152 10011000 168 10101000 184 10111000 200 11001000 216 11011000 232 11101000 248 11111000

88 98 A8 B8 C8 D8 E8 F8

137 10001001 153 10011001 169 10101001 185 10111001 201 11001001 217 11011001 233 11101001 249 11111001

89 99 A9 B9 C9 D9 E9 F9

138 10001010 154 10011010 170 10101010 186 10111010 202 11001010 218 11011010 234 11101010 250 11111010

8A 9A AA BA CA DA EA FA

139 10001011 155 10011011 171 10101011 187 10111011 203 11001011 219 11011011 235 11101011 251 11111011

8B 9B AB BB CB DB EB FB

140 10001100 156 10011100 172 10101100 188 10111100 204 11001100 220 11011100 236 11101100 252 11111100

8C 9C AC BC CC DC EC FC

141 10001101 157 10011101 173 10101101 189 10111101 205 11001101 221 11011101 237 11101101 253 11111101

8D 9D AD BD CD DD ED FD

142 10001110 158 10011110 174 10101110 190 10111110 206 11001110 222 11011110 238 11101110 254 11111110

8E 9E AE BE CE DE EE FE

143 10001111 159 10011111 175 10101111 191 10111111 207 11001111 223 11011111 239 11101111 255 11111111

8F 9F AF BF CF DF EF FF

Copyright (C) Dataplex Pty Ltd C-2

Appendix D INTERFACE CONNECTIONS

INTERFACE CONNECTIONS

The following Section applies to the DPX-213 only. There are two cables required for use with the DPX-213, one cable for the phone line and another cable that is connected between the modem and the terminal. The wiring for these cables is described in this

Section.

Line and Phone Connector

The phone and line connector are both RJ-11 type connectors. The Line Connector has mode 3 connections in addition to the standard tip and ring connections. See the Figure below for details.

PIN LINE

2

3

4

5

6 Leased Line

Not Used

Tip

Ring

Not Used

VIEW LOOKING AT

Leased Line

DPX-213 REAR PANEL

Figure D.1 RJ-11 Connector Wiring

D-1 Copyright (C) Dataplex Pty Ltd

Appendix D

V.24/28 Interface Wiring

INTERFACE CONNECTIONS

The DPX-213 uses the industry standard V.24 (RS-232) 25 Pin interface configured for a modem (DCE - female). It is unlikely that the DPX-213 and your computer will need all the pins shown, some are used only in synchronous operation, while other pins are needed only by certain software packages.

The DPX-213 modem will operate with only three (3) active leads in the cable, transmit data, receive data and ground on Pins 2, 3, and 7.

Table D.1 V.24 Interface Connectors

Pin Function

Protective Ground

Transmit Data

Receive Data

Request to Send

Clear to Send

Data Set Ready

Signal Ground

Carrier Detect

Supply

Reserved

Transmit Clock

Receive Clock

Data Terminal Ready

107

102

109

CCITT

Number

101

103

104

105

106

114

115

108

Direction

(Modem In / Out)

Not Used

Out

Common to Both

Out

SEE NOTE

(Below)

NOTES: 1. Minimum signals for set-up & operation of the DPX-213.

2. Required for RTS/CTS flow control.

3. Optional for the DPX-213, may be needed by your communications package

in asynchronous mode, also needed to access some DPX-213 features such as

DTR dialling and so on.

4. Only required for synchronous operation, best left out of the cable for

asynchronous operation.

5. DC +12VC.

6. These wires are used to extend an internal serial bus out the DB25 connector

and should remain disconnected.

Copyright (C) Dataplex Pty Ltd D-2

Appendix E

E-1

AT COMMAND SET SUMMARY

AT COMMAND SET SUMMARY

Command

ATX

ATZ

AT&C

AT&D

AT&E

AT&F

AT&G

AT&H

AT&I

AT&K

AT&L

AT&M

AT&N

AT&P

AT&T

AT&U

ATA

ATB

ATD

ATDn

ATE

ATF

ATH

ATI

ATNn&Z

ATO

ATP

ATQ

ATSr?

ATS=n

ATT

ATV

Brief Description Section

Repeat command - NO AT prefix

Answer

Bell/CCITT select

Dial command

4-7

4-8

Dial stored number

Echo command

4-9

Communication format/force line speed 4-10

Hook command - hang up 4-10

Identify modem 4-10

Store string in location n

On line, originate and retrain

Pulse dial modifier

Result code & quiet mode

S register inquire

S register set command

Tone dial modifier

Verbose or terse control

4-11

4-12

4-13

Response codes - blind dialing

Modem reset

Carrier detect & DSR options

DTR control

MNP/V42

Load factory defaults from ROM

Guard tone selection

Help screen

Constant Speed Interface

DTE flow control

Leased line control

Sync/Async, dialed stored number

Display or clear dialling directory

Pulse dial make/break ratio

Test modes

Modem flow control

4-17

4-18

4-19

4-20

4-21

4-14

4-15

4-16

4-17

Appendix E

AT COMMAND SET SUMMARY

AT COMMAND SET SUMMARY

Command

AT&W

AT&Z

AT*A

AT*C

AT*D

AT*E

AT*G

AT*P

AT*R

AT*Y

Brief Description Section

Write active configuration to NVRAM 4-22

Store phone number to NVRAM 4-22

Alarm mode.

Configuration screen

4-23

Dumb mode

Data compression.

Interrupted calling tone.

Password security

Remote configuration

4-24

4-25

4-25 Break handling

Dial Modifiers (See ATD command)

Dial stored number

Pulse dial

Tone dial

Pause (S8 seconds)

4-8

4-9

Copyright (C) Dataplex Pty Ltd E-2

INDEX

Accessories

Answering a call

number of rings

Alarm/alert mode

delay

Applications

ASCII conversion table

Asynchronous communication mode

mode

AT commands

description

ignore

NO 'AT' response

remote entry

summary

Attention code

Autobaud

Autoranging

Automatic

answer/originate

calling

line rate detection

tone/pulse selection

Back space character

Baud rate (changing)

BELL/CCITT select

Bit mapped registers

Blind dialling

Break mode control

Cabling requirements

Calling

automatic and manual

establishing & terminating

tone

Carriage return character

Carrier detect

control

loss of carrier (response time)

CCITT/BELL selection

Characters

ASCII table

back space

carriage return

escape

extended character format

flow control

line feed and length

Clock source (asynchronous control)

Command

entry, structure and format

parameters and states

remote entry

repeat

state

summary

Communication software

Compatibility (hardware / software)

Configuration

async and sync modes

default (factory)

displaying and writing

remote

Connecting the modem

Connectors

RS-232

RJ-11

Constant speed interface

9-2

2-6,4-7

8-3

4-23,5-6,8-6

8-9

5-1

C-1 to C-2

4-20,5-2 to 5-3,6-1

4-20,8-7

4-6

4-1

8-6

2-7

See Remote configuration

E-1 to E-2

4-2 to 4-3

3-2

3-2,4-10

3-3,4-11,8-13

3-1

4-10

4-9,4-12,4-13,8-5

4-2,8-4

See Data transfer rate

4-7,8-6,

8-5 to 8-9

4-14

4-25,8-7

1-1

3-1

2-5,2-6

4-24,8-6

4-2,8-3

4-15,8-4,8-5

8-5

4-7,8-6

C-1 to C-2

4-2,8-4

4-2,8-3

3-3,8-3

5-5

8-8

8-3,8-7

5-3,8-7

3-1,4-1 to 4-3

4-3 to 4-6

See Remote configuration

4-3,4-7

4-4, see Escape sequence

E-1 to E-2

3-1,6-6

6-6

6-1 to 6-3,5-2 to 5-3

2-5,4-16,5-1

4-22,4-23

4-25,5-7,8-6

2-1 to 2-7

D-1

4-15,D-2

2-1,D-1

Data compression

Data bits (setting)

Data format (setting)

Data transfer rate (speed)

Data transfer state

Default configuration

Diagnostics

power on and reset

testing

Dial command

pause time

tone

Dial modifiers

Dialling

call progress

directory (clear and display)

leased lines/dial-up operation

stored/storing numbers

tone/pulse selection

DTMF tone duration

DTR (Data Terminal Ready) control

Dumb mode control

Echo (enable/disable)

Error

control

correction

Escape sequences and character

guard time

Extended character formats

Factory configuration

Features

advanced and summary

Flow control

buffers

characters

modem

RTS/CTS

user

Xon/Xoff

Front/rear panel

indicator name / functions

Guard time (escape code)

Guard tone

Handshake

Help (AT Command)

Hook command/control

Idle state

Inactivity timer

Initiating self tests

Initialisation string

Installation

making/closing a connection

service record

setting the PC and testing

trouble shooting

Interface connections

3-2,4-7,4-10,4-17,6-5,8-

4-16 to 4-18,6-4,8-7

2-5,3-1,5-5

2-4,4-10

2-4,4-10,6-1,8-6,8-7

4-5

2-5,4-16,5-1

4-15,7-1

See Testing

4-8 to 4-9, See Dialling

4-9,8-4

2-5,2-6,4-9,8-5

4-8 to 4-9

4-14

4-20

3-2,4-19,5-4,8-5

4-9,4-11,4-22,5-6

4-9,4-12,4-13,8-5

4-9

4-15,8-5,8-6

2-6,4-2,4-24,8-6

4-9,8-5

3-2,4-24,6-1 to 6-5,8-7

4-24,4-16,6-1 to 6-5,8-7

3-3,8-3

8-5

5-5

2-5,4-16,5-1

See Specifications

1-1,3-3,35

3-2,6-2 to 6-6,8-7

6-2

8-8

8-7

4-18,4-21,8-7

4-21

See Xon/Xoff flow control

2-1,2-3

2-3

8-5

4-17,8-6

See Data transfer

4-17

4-10

4-4

8-8

7-1

3-1

2-1,2-2

2-5,2-6

10-2

2-4

2-7

D-1,See also Connectors

INDEX

Jack type selection

Jumper locations/setting

Leased line / dial up operation

modes

LED (front panel indicators)

Line feed character

Lines

dial-up

leased lines

Loading default configuration

Local analogue loopback test

Low power mode

Make / break ratio

Manual calling / dialling

Master reset

MNP

error control

data compression

delay (autoreliable)

Modem

basics

resetting

testing

Modifiers (dial)

Network operation

New Zealand dialing

Non volatile memory (NVRAM)

Null modem cable connection

See Connectors

2-2

3-2,4-19,5-4

8-5

2-3,7-1,7-3

8-3

3-2

3-2,4-19,5-4

See Configuration

4-21,7-2

5-6

4-20

3-2

2-7

6-4

3-2,4-18,4-21,6-2 to 6-6

4-16 to 4-18,6-4,8-7

8-9

3-1

2-5,4-15,4-16,5-1

See Testing

4-8 to 4-9

See Leased line / dial up

8-5

2-1,3-1,4-16,4-22

2-3

Off-hook

Online command state

Operating states or modes

leased line

PABX operation

Parity (changing)

Password protection

enabling

Pause modifier (,)

Pinouts

Problem report sheet

Protocols

Pulse dialling

make/break ratio

Quiet mode

2-6,8-4

4-6

4-3,5-1

3-2,4-19,5-4,8-5

2-5,3-2,4-14,5-5,8-4

2-5,5-5,8-6

3-3,4-11,4-25,5-6,8-6

4-11,4-25

4-10,8-4

See Connectors

A-1

See Section 6

4-9,4-12,4-13,8-5

4-20

4-12

Recalling a command string

Redial attempts and delay

Registers (status)

Remote configuration

Remote digital loopback test

Remote loopback response

Repairs and warranty

Repeat command

4-8,4-13

8-8,8-9

See S Registers

4-25,5-7,8-6

4-21,7-2

10-1 to 10-2

4-3,4-7

Requirements (software and hardware) 1-1

Resetting the modem 2-5,4-15,5-1

Result codes

enabling/disabling

4-3

4-13,4-14,8-5,8-7

table

text/numerical format

Retrain

Ring answer and count

4-14

4-13,8-5,8-7

4-11

8-3

RTS/CTS

flow control 4-18,4-21,8-7

S Registers

configuration

format

setting, retrieving and displaying

summary table

Safety

Security

Sending data

Servicing (DPX-213)

Software compatibility

Specifications (technical)

Speed

connect speed

CSI (Constant Speed Interface)

3-1,4-1,4-3,8-1

8-1,8-2

8-2

4-12,4-13,4-23,8-2

B-1

See Password protection

See Applications

See Warranty and repairs

6-6

9-1 to 9-2

4-10

See Constant speed int

matching and setting (baud/ bps) See Data transfer rate

Standby mode 5-6

States (operating)

Status registers

4-3,4-19,5-1,5-4,8-5

See S Registers

Start / stop bits (changing)

Storing strings in NVRAM

Summary

See Parity

4-11,4-22

AT commands

S registers

Synchronous communication mode

E-1 to E-2

B-1 to B-2

4-20,5-1,5-3

Tables

Telephone

connection

dialling

line connection

storing a number

Test / Dial button

Testing

connections

for 'AT' response

types (modes)

Tone dialling

Transmission speeds

altering

Transmit level

Troubleshooting

no 'AT' response

V.42

V.25bis

V.25

V.24 test lead control

Verbose (response codes)

Wait for dial tone

Wait for carrier

Warranty

See CONTENTS at front

of manual

See Installation

See Dialling

See Installation

See Dialling

See Front Panel

7-1,8-7,

2-4

2-7

4-21

4-9,4-12,4-13,8-4 to 8-6

See Data transfer rate

9-1

2-7,See aslo Testing

See MNP

5-1

4-24

D-2

4-13,4-14,8-5,8-7

4-14,8-4

10-1

XModem

Xon/Xoff flow control

characters

YModem

ZModem

6-1 to 6-6

4-18,4-12,6-2 to 6-6,8-7

8-7

6-1 to 6-6

D a t a p l e x P t y. L t d.

Incorporated in NSW A.C.N. 003 053 343

Level 2, 71 Epping Rd, NORTH RYDE NSW 2113

AUSTRALIA

DPX: (612) 02 9869 2500

FAX: (612) 02 9869 2600 www.dataplex.com.au

[email protected]

สวัสดี! ฉันคือแชทบอท AI ที่ได้รับการฝึกฝนมาโดยเฉพาะเพื่อช่วยเหลือคุณเกี่ยวกับ Dataplex DPX-213 User manual ฉันได้ตรวจสอบเอกสารอย่างละเอียดและสามารถช่วยคุณค้นหาข้อมูลที่ต้องการได้อย่างแม่นยำ หรืออธิบายเนื้อหาด้วยคำศัพท์ที่ชัดเจนและเรียบง่าย ไม่ว่าคุณกำลังมองหาคำแนะนำเกี่ยวกับคุณสมบัติเฉพาะ ขั้นตอนการแก้ไขปัญหา หรือการใช้งานทั่วไป โปรดถามคำถามของคุณได้อย่างอิสระ ยิ่งคุณให้รายละเอียดเกี่ยวกับข้อกังวลหรือความต้องการของคุณมากเท่าไหร่ ฉันก็จะสามารถช่วยเหลือคุณได้อย่างแม่นยำและมีประสิทธิภาพมากขึ้นเท่านั้น!

ผู้ช่วยกำลังพิมพ์

ผู้ช่วยไม่ได้อยู่ที่คีย์บอร์ด โปรดลองอีกครั้งในภายหลัง

ดูเหมือนว่าคุณจะเข้าถึงเอกสารที่เขียนด้วยหลายภาษา รวมถึงภาษาที่ไม่ใช่ภาษาแม่ของคุณ คุณสามารถใช้ลิงก์ต่อไปนี้เพื่อซ่อนหน้าต่างๆ ที่ไม่มีภาษาที่คุณต้องการชั่วคราว

โฆษณา