Konig & Meyer 19713 Quick Manual

19713 iPad mini stand holder
- Great Appearance! The best way to present your iPad mini.
- The mount securely holds the iPad mini.
- At the same time it is suitable for the stage, home and studio.
- Thanks to the 3/8"(5/8")-thread, it can be mounted to each microphone stand.
- It is easy to clip the iPad mini onto the specially adapted holder.
- It can be set to any position (vertical/horizontal) and format (portrait/landscape).
Thank you for choosing this product. The instructions provide directions
to all of the important set up and handling steps. We recommend you
keep these instructions for future reference.
SAFETY NOTES
- Only use suitable stands: Stability, 3/8"(5/8")-thread;
- preferably K&M microphone stands or microphone holders ASSEMBLY
- Carefully clip the iPad mini onto the mounting plate and
PLACEMENT & REMOVAL of the IPAD MINI
- ensure that the iPad fit is secure
Volume Control
- Careful handling; especial when changing the
- position/format
On / Off
- Specially adjusted to the iPad mini
Camera (Back)
Switch
Lightning
connector
SET UP INSTRUCTIONS
ASSEMBLY
Assembly of the iPad mini holder is simple.
The prerequisite is a suitable stand
(see above SAFETY NOTES).
1 Turn the knurled washer (3/8") until it cannot go any
1 further onto the thread of the stand.
2 This is followed by screwing on the mount
3 Tighten the mount and knurled washer
4 Tighten the wing nut
Placement of the IPAD MINI
5 Place the iPad mini according to the HOME-Button
5 Symbol (is embossed on one side of the holder)
6 First PLACE the iPad mini into the bottom area and then...
7 ...and CLIP it into the top.
The disassembly is carried out in a reversed order.
Microphone
Speaker
Microphone
Camera (Front)
3,5 mm
connector
Home-Button
(the holder is embossed with information on where the iPad mini is to be placed)
(false placement results in the embossed user elements being covered up! Please note)
top
CLIP ON
Lift up
the hook
bottom
PLACE
Remove
USAGE NOTES
The iPad mini holder can be adjusted according to the
position and format. The iPad mini does not have to be
removed from the holding plate to make the adjustments.
POSITION
The iPad mini can be placed in any vertical / horizontal
position, the final position can be set. To do this:
10 Hold the iPad mini and loosen the wing nut somewhat
11 Pick the position (vertical / horizontal) and
12 Re-tighten the wing nut.
POSITION
Final Position
- horizontal
- as far as it will go
FORMAT
The holder is equipped with a 90°- rotating function.
This allows the presentation of the iPad mini in the
FORMAT
portrait and landscape positions.
13 Turn the holding plate either in the portrait or landscape
13 position - or it can be tilted.
- Hitches within the mount limit how far the holder can be
- turned.
- In addition, the holding plate clicks into place for both final
- positions, which means, that a the iPad mini will stay in the
Final Position
- selected position.
- landscape
FAULT FINDING (F) & REPAIR (R)
F: Holder is unstable
F: R: Check that it is properly screwed into the stand, if
F: R: needed tighten the screws 1-3
F: R: Tighten the wing nuts 4
F: iPad mini is not positioned in the holder properly
F: R: Place the iPad mini into the holder correctly 6 and click
F: R: it into place 7
F: R: If needed, carefully bend the holding plate inwards
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19713-300-55 Rev.6 / 19712-500-55 Rev.4 03-80-106-00 6/13
- click into place
Incline Position:
- tilted (0-90°)
- select any position (Secure position
- by tightening the wing nut)
Incline Position:
- tilted
- does not click into place but it
- does stay in the selected position
Final Position
- vertical
- as far as it
- will go
Final Position
- portrait
- click into place
TECHNICAL DATA
Swivel Bearing: Polyamid PA-6
Holding Plate: PP
Screws, nuts, washers, springs: steel galvanized
Max. load
iPad mini
208,7 x 89,6 x 143,7 mm
Dimensions
Box: 235 x 90 x 171 mm
Weight
net 0.49 kg, gross 0.67 kg
Material
19713
iPad mini stand holder
Product variant
19713-300-55 - black 3/8"
Data
Bearing plate
208.7 x 143.7 mm
Material
plastic
Max. load capacity
0.75 kg
Special features
to be screwed on to 3/8" threaded bolts;
iPad mini is easily clipped into the holder;
lightning connector and headphone jack are
accessible;
freely rotates 90°;
suitable for iPad mini 1st generation
Suitable for
3/8" thread
Swivel
90 º
Type
black 3/8"
Weight
0.49 kg
A clever way to show off your iPad mini. The mount is guaranteed to hold the iPad mini effectively and safely. For use on stage,
in the rehearsal room or at home - the 3/8" internal thread means the holder can be attached to any microphone stand easily and
quickly. The iPad mini is clipped in and out of the holder effortlessly. An easy-to-use wing nut adjusts the tilt so the user can
easily find a position to suit them. The iPad mini switches rapidly between the vertical and horizontal format without slipping.
">