Hyundai - IMDS Information Pages - International Material Data

HyundaiㆍKia IMDS Guidance

Version. 8.2

Revision

IMDS 3.1

IMDS 4.0

IMDS 5.0

IMDS 6.0

IMDS 7.0

IMDS 7.1

IMDS 7.1-1

IMDS 8.0

IMDS 8.1

IMDS 8.2

Korean

2005.7.15

2006.6.1

2007.5.28

2008.7.9

2009.9.1

2010.6.1

2011.4.15

2012.6.22

2013.5.27

2014.5.13

English

2006.2.21

2006.5.17

-

-

-

-

-

2012.6.22

2013.5.27

2014.5.13

Changes

Recipient, IMDS service center

Applied plant, Recipient, Change terms

Hyundai,Kia IMDS(International Material Data System) Guidance is the minimum requirement when creating MDS (Material Data Sheet) submitted by suppliers. It is used as the acceptance criteria for accepting or rejecting MDS, and suppliers sending MDS are responsible for disadvantage caused from noncompliance with this guidance. It is prohibited to distribute this guide with arbitary revision

Summary

1. Please be well-informed of basic IMDS instructions from following documents before read this guidance

1) General system instruction

: http://mdsystem.com

→ See ‘Online user manual’ in System Login screen

2) How to create materia

: http://mdsystem.com

→ See ‘How to create a material MDS’ in System Login screen

3) How to create component

: http://mdsystem.com → See ‘How to create a component MDS’ in System Login screen

4) IMDS Recommendations

: http://mdsystem.com → System Login → See ‘Recommendation’ of the ‘Help’ in main

screen

2. This guidance is written based on IMDS Recommendations and if guidance and

Recommendations have discord, please follow this guidance.

3. MDS recipient should be based on corresponding vehicle manufacturing plant. MDS sent to other recipient is not valid even if it is accepted (refer to 3.1.1 of this guidance)

Company Plant MDS org. unit ID Recipient

HMC

All Domestic Plant, Czech

Plant(HMMC), India Plant (HMI),

Turkey Plant(HAOS)

Alabama Plant(HMMA)

71405

119671

HYUNDAI MOTOR COMPANY

HYUNDAI MOTOR ALABAMA

(HMMA)

KMC

All Domestic Plant,

Slovakia Plant(KMS)

Georgia Plant(KMMG)

71406

119673

KIA MOTOR CORPORATION

KIA MOTOR GEORGIA (KMMG)

1

4. Please call to followings for any questions about system

- Hyundai, Kia Motor (reject reason, MDS acceptance criteria, ISIR related etc)

Work Scope Responsibility Phone Number Email

General

Kim, Young chul +82 31 8036 3577 [email protected]

Hyundai

Motor

Park, Hye Young +82 31 8036 3579 [email protected]

Kia Motors

Kim, Hye Joung +82 31 8036 3578 [email protected]

- IMDS Service Center (access authority / instructions / IMDS Recommendations etc)

Region

Korea

Europe

North

America

France

Japan

China

Service Hour

(Mon~Fri, local time)

9:00am - 05:00pm

8:00am - 4:30pm

8:00am - 5:00pm

8:00am - 4:30pm

9:00am - 5:00pm

9:30am - 5:00pm

Phone Number

+82 2 2199 0203~4

+36 1 778 9821

+1 972 403 3607

+33 1 57 32 4856

+81 3 4530 9270

+86 27 8743 1668

Email [email protected]

[email protected]

[email protected]

[email protected]

[email protected]

[email protected]

2

- Table of Content -

1. Check Point before creating MDS

1.1 Background of IMDS

1.1.1 IMDS Operation Backgroud

1.1.2 IMDS Acces Authority Request

1.1.3 Access IMDS

1.2 Timing of Sending MDS and Application Scope of IMDS

1.2.1 Timing of Sending MDS

1.2.2 Application Scope

1.3. Input Conformity

1.3.1 IMDS Recommendations

1.3.2 HyundaiㆍKia IMDS Guidance

1.4. Understanding Basic Property of MDS

1.4.1 How to Express Elements of Part as Characters and Tree Structure

1.4.2 Understanding Part and Data Flow through supplier chains

1.4.3 Measuring Part Weight and Analysis of Substances in Material

1.5. 4 Heavy Metals Threshold / Material Marking

1.6. IMDS-ISIR Work Flow

2. How to Create MDS

2.1 ID / Version Management

2.2 Description and Part / Item Number input

2.3 Material Classification Selection

2.3.1 Condition of containing Basic Substance for Material Classification

2.3.2 Chemical Non-Content Condition for each Material Classification

2.4 Material Name Input

2.5 Parts Composition

2.5.1 Creating Tree Structure

2.5.2 Part Composition including Direct-Purchased parts

2.5.3 Creating Material Data at each Material Characteristics

2.6 Ranged Values

2.7 Weight Tolerance of MDS

2.8 Basic Substance Information

2.9 4 Heavy Metals and their Application Code

2.10 Material Marking

2.11 Contact Person Assignment

3. Sending MDS and Feedback

3.1. Sending MDS

3.1.1 Choice of Recipient

3.1.2 Input Supplier Code

3.2 Feedback after Sending MDS

3.2.1 How to modify rejected MDS

3.2.2 When part changes occurs


HyundaiㆍKia IMDS Guidance

1. 1 Backgrouds of IMDS

1.1.1 IMDS (International Material Data System) Operation Backgrouds

It is a web-based system developed and operated by automobile manufacturer and solution company, HP in order to cope with global chemical regulations, and it secures and controls chemicals as well as weight information of automobile parts through supply chain (raw material supplier  tier 2 nd  tier 1 st  automobile manufacturers)

1.1.2 IMDS Access Authority Request

- If your company access to IMDS for the first time

: You can take the access authority through the online registration in homepage blow

※ Webpage http://mdsystem.com

→ New to IMDS → ‘Company Registration’ → follow

registration procedure after click ‘ Online Registration ’

- If Your company already registered to IMDS

: Request access authority to your client manager

※ But, please check with IMDS service center for your registration (refer to ‘Summary’ of this

guidance for inquiry)

1.1.3 Access IMDS

http://mdsystem.com → click ‘Login’ → Input User ID and Password → After change password (8~12 digits combining alphabet and number), the service is available

1.2 Timing of Sending MDS and Application Scope

1.2.1 Timing of Sending MDS

- Without specified, MDS input and acceptance should be completed one month prior to M stage

of corresponding vehicle development stage.

＊ MDS (Material Data Sheet) : IMDS data input unit

- If specifications of part are decided after M stage, MDS of the parts should be input right after specification decision.

- Since it takes a while in preparing MDS, processing and modification, please send it with sufficient

time and keep in mind MDS processing takes average of 3~5 days after recieved by us

3



1.2.2 Application Scope

Category Application Scope

Vehicle Type Passenger Car and Truck below the total weight of 3.5 ton

Target Part

• All the ISIR target parts (end-item base)

- New developed parts applying to new car and F/L

- Upgrade parts which has been applied to existing velicles

• When there is change of Engineering Order , material and weight change

(over 3% of total weight), previousely approved MDS should be revised and

re-approved

• When HMC / KMC request MDS additionally to comply with various

environmental regulations

※ MDS which is not the ISIR target or not requested by HMC /KMC does

not need to be sent

Region

All domestic plants, Hyundai Czech plant(HMMC), Hyundai Turkey Plant(HAOS),

Hyundai India Plant(HMI), Kia Slovakia plant(KMS).

but it can be changed according to global policy of HMC / KMC

• Raw material supplier : send MDS to tier n

• Tier 2/3/4/..n : send MDS to upper level through supply chain

Supplier

• Tier 1 : Creating MDS after collecting from lower level supply chain

→ send it to HMC /KMC

• How to input Assembly part including direct purchased part *

- Input all the data except direct purchased part, but follows our rule

regarding direct purchased part (refer to 2.5.2)

Chemicals

Input basic substances only existing in final products

: Except in-process materials during part manufacturing and materials created

in-process but excluded in the final products

* Direct purchased part : Developed between a supplier and HMC/KMC independently, But it goes

to another tier 1 and assembled with other sub-parts. Then the assembly is going to HMC/KMC.

1.3 Input Conformity

1.3.1 IMDS Recommendations

- Since IMDS recomendations were written by mutual agreement between IMDS Steering Committee

and members and are common operation standards for all automobile manufacturers worldwide who

are operating IMDS, users should conform to them with fully understanding when writing MDS in

order not to cause any disadvantage due to input error.

- But, each car manufacturer can request different rules in the Recommendations or additional rules

besides these Recommendations depending on their internal situation.

4



1.3.2 HyundaiㆍKia IMDS Guidance

- All of the suppliers sending MDS to HMC / KMC should follow ‘HyundaiㆍKia IMDS

Guidance’ and guidances by all automobile manufacturers including Hyundai, Kia can be inquired from http://mdsystem.com > IMDS Information pages > Help > FAQ > OEM specific information

1.4 Understanding Basic Property of MDS

1.4.1 How to Express Elements of Part as Characters and Tree Structure

① Parts in IMDS are expressed as icon as following and should be observed when creating MDS

Category Term Description Icon Sample

Component

Define assemly part or sub-part consisting assembly part

Semi-component

Used in semi-product need to proceed additional process step (cutting, stamping).

The addition of dimensional data (g/m3, kg/m, kg/m2) is possible.

Material

Material composing components and is consisted of basic substances

Basic substances

Chemicals composing materials and minimum unit with material characteristics

② Part assembly structure is expressed as tree structure in IMDS and should be conform to actual part

composition when creating MDS.

<Part Composition>

Bolt-washer assy

(BOLT + WASHER)

Striker

Screw

Striker & witch assy

Switch assy

(BRACKET + SWITCH)

<MDS composition with tree structure>

5



③ MDS should be created in conforming with part composition, quantitiy, material and surface treatment

in drawing

<Part Composition in Drawing>

Conform to part composition

(1개)

(1개)

(1개)

(1개)

(1개)

<MDS Composition & sQuantity of sub-parts>

Material/ surface treatment conformity

<Material and Surface Treatment in BOM>

<Material Surface Treatment in MDS>

1.4.2 Understanding Part and Data Flow through supplier chains

Check part and data flow through tier 1/2/3/4

- Classfying as ordinary parts and direct purchased parts

- Figuring out responsible person of each suppliers and data trasmission and reception path

1.4.3 Measuring Part Weight and Analysis of Substances in Material

- Figure out the weight of assembly and sub-parts, and reflect them to data sheet

- Figure out all materials composing parts (major material, additives, other fillers and stiffners etc) and

reflecting results to data sheet after analyzing substances at each material through authorized

analysis agency or own analysis

- Published data by raw material suppliers in IMDS can be used, but material composition in

published data should be conform to your material composition

6



1.5 4 Heavy Metals threshold / Material Marking

- If 4 heavy metals are existed, check whether it is below the threshold. If not, check whether it

is allowed followed by Permission for exceptional use of heavy metals in MS201-02

(refer to Hyundai,Kia Material standard MS201-02 ” Prohibition and

reporting the use of harmful

substances-

parts and materials”)

※ Maximum concentration value ( wt% represents weight percentage)

Maximum concentration value in homogeneous material wt%* (ppm)

MS201-02

Lead, Mercury, Hexavalent Chrome 0.09 (900)

Cadmium 0.009 (90)

- Check material marking for plastic and rubber materials.

(refer to Hyundai, Kia Material standards MS 201-01 “Marking of materials for automotive parts”)

7



1.6 IMDS – ISIR Work Flow

MDS for ISIR target parts (developed part or changed part) should be approved according to

following work flow and the first page of approved MDS should be captured and submitted to

the ISIR Supervision Department

※ MDS which is sent to wrong recipient or not approved is not valid (refer to 3.1.1)

Sending MDS

IMDS Recommandations

HMC / KMC IMDS Guidance

MS201-01

MS201-02

Suppliers

I M D S

Check regulation and input guide conformity

Rejected

No

Data

Accuracy? supplier / Raw Material Supplier

/ Oversea supplier

Approved

No

No

Yes

Satisfy heavy metal ban?

Accept/

Reject

Yes

Basic part

Information?

Yes

Eco Technology

Research Team

[Hyundai] [Kia]

Part Informaion Matching

BOM

Capture the first page of approved

MDS screen and submit

(Hyundai, Kia) ISIR Supervision

Department

ISIR Final Approval

8

2. How to create MDS


2.1 ID / Version Management

- What is ID / Version?

ID is the number created automatically when creating MDS and Version means change history

of data sheet. Basically, the same ID is used for the same part number.

(Version)

(ID)

[ID / Version]

- MDS sent to HMC / KMC should be conformed to following rules.

● Creating data sheet with new ID : In case of the first IMDS input part, new developed part,

changed part number of part

● Modified with same ID and version-up : When already created MDS is changed (EO change,

material change, total weight change of +-3%, color change and request of MDS re-entry

due to regulation related issue)

※ Even approved MDS should be reapproved after reflecting changes when material, weight,

component, color etc changes

New part

Number

New ID

GADSL

Change

Material

Change

Part Weight

Change

Version up with same ID request of MDS re-entry due to regulation related issue

[ID / Version management rules when creating data sheet]

9



※ Reference : How to select ‘Copy’ option of existing data sheet

- After click copy button,

: Choose ‘New Version’ → Existing data sheet is modified with the same ID and version-up

(Example : 114918315/

0.01

→ 114918315/

0.02

)

: Choose ‘Copy’ → Data sheet is created with new ID

(Example : 11491831

5

/0.01 → 11491831

6

/0.01)

10



2. 2 Description and Part / Item No. Input

- Description field should be ‘conform’ or ‘similar’ to part name in HMC / KMC BOM (Bill of Materials) and be written with English capital letter

- Part/Item No. should be ‘conform’ to part number in HMC / KMC BOM.

● Description

- Input part name “conform” or “similar” to HMC / KMC BOM

- Part name should be written with English capital letter

Nonconform Case ASM-KIA-MG SEAT BELT ASSY-FR P/T 3PT, LH → Reject

Similar Case I.S.C ACTUATOR IDLE SPEED CTL ACTUATOR → Accept

● Part/Item No.

- Should be followed to the typical format of HMC / KMC BOM

※ HMC / KMC part No. format : 12345-67890 ☜ insert ‘-’ between number 5 digit and 5 digit.

No word spacing necessary

- If same part number but differnt color only, adding color mark with alphabet combination or

alphabet-number combination after part number is possble.

Example) 56900-3L100

WK

, 37160-2G000

T3

- If part number is different for the same part name , each part number should be transmitted

separately.

Example) 88870/88880-1E000 → 88870-1E000 (transmit), 88880-1E000 (transmit)

- Since directly supplied materials such as lubricant, fuel, paint, sealant, etc do not have

their part number, supplier’s internal part number can be available

11



2.3 Material Classification Selection

Since material classification is the key for matreial marking, application codes of heavy metals and

recycle information, it should be properly selected according to material characteristics.

(refer to below material content condition table at each material classification)

2.3.1 Chemical Content Condition for each Material Classification

- It should satisfy chemical content condition according to material classification

Clssif icatio n No.

1.1

Classification Name

Steels / cast steel / sintered steel

1.1.1 unalloyed, low alloyed

1.1.2 highly alloyed

1.2

1.2.1

Cast iron

Cast iron with lamellar graphite / tempered cast iron

1.2.2

Cast iron with nodular graphite / vermicular cast iron

1.2.3 Highly alloyed cast iron

2.1 Aluminum and aluminum alloys

2.1.1 Cast aluminum alloys

2.1.2 Wrought aluminum alloys

2.2

2.2.1 Cast magnesium alloys

2.2.2 Wrought magnesium alloys

2.3

Magnesium and magnesium alloys

Must contain

*

Iron (Fe) ≥ 50%

Iron (Fe) ≥ 65%

Iron (Fe) ≥ 30%

Iron (Fe) ≥ 50%

Iron (Fe) ≥ 70%

Iron (Fe) ≥ 55%

Iron (Fe) ≥ 14%

Aluminum (Al) ≥ 50%



Sum of Mg and Magnesium powder (stabilized) ≥ 50%



Titanium (Ti) ≥ 50%

CAS No. or

Substance Group

7439-89-6

7439-89-6

7439-89-6

7439-89-6

7439-89-6

7439-89-6

7439-89-6

7429-90-5

7429-90-5

7429-90-5

Chk : Magnesium

Chk : Magnesium

Chk : Magnesium

7440-32-6

3.1

3.2

3.3

3.4

3.5

Titanium and titanium alloys

Copper (e.g. copper amounts in cable harnesses)

Copper alloys

Zinc alloys

Nickel alloys

Lead

Copper (Cu) ≥ 93%

Copper (Cu) ≥ 48%

Sum of Zinc substances ≥ 70%

Nickel (Ni) ≥ 50%

Lead (Pb) ≥ 50%

7440-50-8

7440-50-8

Chk : Zinc

7440-02-0

7439-92-1

* Corresponding chemicals should be contained more than written content.

(Ex) Material Class, 1.1 Steels / cast steel / sintered steel should contain over 50% of iron (Fe).

12


<Continue>

Clssif icatio n No.

4.1

4.2

5.1.a

5.1.b

5.2

5.3

5.4

5.4.1

5.4.2

5.4.3

6.1

Classification Name

Platinum / rhodium

Other special metals filled Thermoplastics unfilled Thermoplastics

Thermoplastic elastomers

Elastomers / elastomeric compounds

Duromers

Polyurethane

Unsaturated polyester

Other duromers

5.5.1

Plastics

(in polymeric compounds)

Lacquers

Must contain

*

Sum of platinum and rhodium ≥ 50%

Other metals or their sum ≥ 50%

Sum of substances containing …poly… in their names excluding sum of Basic

Duromers ≥ 23%

Sum of substances containing

…poly…in their names excluding sum of Basic Duromers ≥ 25%

Sum of substances containing

…poly…in their names excluding sum of Basic Duromers ≥ 25%

Sum of Basic Rubbers or substances containing …poly… in their names excluding Basic Polymers and Basic

Duromers and ≥ 10%


Polymers ≥ 15%

Sum of substances containing …poly… in their names ≥ 25%


Polymers ≥ 15%


Polymers ≥ 15%

Sum of substances containing …poly… in their names ≥ 25%

Sum of Basic Duromer or …poly ≥

25%


CAS No. or Substance

Group

Chk: Platinum / Rhodium

Special metals

Chk: Named *poly* w/o duromers

Chk: Named *poly* w/o duromers

Chk: Named *poly* w/o duromer

Chk: Named *poly* + elastomer w/o polym./durom.

Chk: Named *poly* w/o polymers

Chk: Named *poly*



Chk: Named *poly*

Chk: Named *poly* and duromers

13



2.3.2 Chemical Non-Content Condition for each Material Classification

- When creating data sheet, following selected material classification should satisfy corresponding

chemical non-content condition

Materi al

Class

5.5.2

6.2

6.3

7.1

7.2

9.1

9.2

9.3

9.4

9.5

9.6

9.7

9.8

Material Classification

Name

Must not contain

*

Textiles

(in polymeric compounds)

Adhesives, , sealants

Underseal

Sum of substances corresponding to material classification 1~4 ≥ 50%



Modified organic natural materials (e.g. leather, wood, cardboard, c...


Ceramics / glass

Fuels

Lubricants

Brake fluid

Coolant / other glycols

Refrigerant

Washing water, battery acids




Sum of substances corresponding to material classification 1~4 ≥

50%




Preservative

Other fuels and auxiliary means



CAS No. or Substance

Group

Chk: Classification 1-4













* Corresponding chemicals should not be contained over written content

(Ex) In material classification 5.5.2 Textiles (in polymeric compounds), sum of substances corresponding

to material classification 1~4 should not be contained over 50%

14



2.4 Material Name Input

- Name to defining material should be used but commercial

name should not be used

: Material name writing should follow below standards

① Steel : EN10027, JIS Standard (ex. STM-C 540)

② Aluminum Alloy : EN 573, JIS Standard (ex. AI-Si12)

③ Copper Alloy : ISO Standard (ex. CuAl5)

④ Plastic : ISO 1043-1~4 (ex. PE-LD)

⑤ Rubber : ISO 1629 (ex. ACM)

⑥ TPE (Thermoplastic Elastomers) : ISO 18064

(ex. TPA-ES)

- If 4 heavy metals are included, material names considering the

exception defined by ELV Directives should be used (ex. SOLDER etc)

<Material Name Input Screen>

2.5 Parts Composition

2.5.1 Creating Tree Structure

- MDS should be created with tree type by combination of component, semi-component, material

and basic substance. See the correct examples as refernece

● Correct Tree Structure (example

● Incorrect Tree Structure (example)

Material ( ) must be

Loacated between component and substances

Material ( ) must be

Loacated between semicomponent and substances

Same level component ( ) and material( ) can’t come together

15



- Same materials ( ) should be composed by integration with one material

Tube assy holder

DC04;St 4; St14 carbon manganese phosphorus sulphur

Iron

2.5.2 Part Composition including Direct-Purchasing parts

- When Direct-Purchasing parts are included in Assembly, input all the data except Direct-

Purchasing parts. In case, Direct-Purchasing parts should be expressed as DUMMY PART

※ Except above case, dummy part can’t be used

[Example] Assembly having Direct-Purchasing parts

LEVEL

1

2

2

2

Part Name

WHEEL-ALUMINUM

NUT-TPMS

VALVE-TPMS

Part No.

MODULE-WHEEL & TPMS 52909-2S320

52910-2S200

52930-2F000

4700-1X000

QT

-

1

2

2

Remark

-

-

-

Direct Purchasing part

If VAVLVE-TPMS is Direct-Purchasing parts, express it as dummy part (refer to below)

● How to make DUMMY PART

- For details of component, input below values for all the dummy part

►

Description → ‘DUMMY PART’

► Measured weight per Item → ‘1g’

► Part/Item No. and Quantity→ actual quantity and part number

(1)

(2)

DUMMY PART (2)

16



● How to add Dummy material to DUMMY PART

① Search published data by HMC / KMC (

ID : 251168843

) and attach it to DUMMY PART

② Weight : ‘

1g’

DUMMY PART

Weight : ‘ 1g ’

Search with ID ‘

251168843

’ in published search field

2.5.3 Creating Material Data at each Material Characteristics

- General method to create material data sheet follows IMDS Recommendation 001. In adddition, the

material data sheet data according to each material characteristics follows MDS Recommendation

002~023.

- But, next cases should follow below rule

① Each material data sheet should be created seperately for layer with consisted of two or more

different materials

Sliding layer

BEARING SHELL

Al alloy

Steel back

Sliding layer

Al alloy

Steel back

[(Ex) Part composed with layer type by 3 different materials]

3 materials composed separately

17



② Since plastics are composed of polymer and subordinate materials (pigment, filler, flame

retardant, other additives), it can not be composed with single substance only and particularly

for PVC (polyvinylchloride), all contained substances should be written.

③ Basic substances in material should be input for materials remained at final product stage and

exlcude basic substances not remained at final products (Ex : when solvents contained in paint,

ink are evaporated at final product)

2.6

Ranged Values

- Allowable ranges of component, Component, Semi-coponent/Material and Basic substance

● weight or content can be input selectively with range, Fix, Rest and when choose‘range’, below

allowable range values are appliede according to ‘IMDS Recommendation 001’

[alllowable range values]

item

Subcomponent

Content Rate (From X % to Y %)

0 < x ≤ 100%

Tolerance (M = Y % – X %)

Follows tolerances in drawing

Semicomponent/

Material

0 < x ≤ 100% M ≤ 20 %

0 ≤ x ≤ 7.5 M ≤ 3 %

Basic substance 7.5 < x ≤ 20 M ≤ 5 %

20 < x ≤ 100 M ≤ 10 %

<Ranged value of material>

<Ranged value of basic substance>

● Other exceptional tolerance of ranges should follow ‘IMDS Recommendations’

● Semi-components or materials published by IMDS committee can be allowable even if they

exceed tolerance

18



2.7 Weight Tolerance of MDS

- Weight tolerance (deviation between measured weight and automatically calculated weight per item)

of the top-level component (total weight of MDS) can not exceed 3%

[The highest Level Component Weight Tolerance Input]

2.8 Basic Substance information

- Only basic substances con-tained in the final material are to be reported (example: cured adhesives

or paint coatings are entered without the evaporating solvents).

- Basic substances registered to GADSL * should be input. In addition, since GADSL is continuously

updated due to related regulation revision, the latest GADSL should be checked before creating

data sheet ( http://www.gadsl.org

)

* GADSL : Global Atomotive Declarable Substance List

※ If SVHC * not included to GADSL are used, they should be input and not allowed to use wild cards

or confidential

* SVHC : Substance of Very High Concern

● Use of Confidential Substances

Due to corporate confidence, data can be concealed not letting others read it and it can be used

within 10% in homogeneous material

Confidential substances

(30%)

(70%)

(10%)

(3%)

(15%)

(30%)

(42%)

19



If confidential substances are to use inevitably over 10%, MDS can be transmitted after designating

‘Trust user’ and in this case, only trust user and data creator can see substance information.

※ Trust User: it is designated when corporate confindential substance composition is open to

particular addressee only. Trust user can not use data for other purposes other than data

evaluation.

★ Trust User

Hyundai Kia Motors. Eco Technology Research Team Park Hye Young

● Wild cards

- It is used for very high confidential and can not be exceeded over 10% in homogeneous material.

(refer to ‘IMDS Recommendation 001’ for the kinds of wild card and how to use them)

But, published material having wild cards by IMDS committee is allowed even though over 10%

of wild cards are used in homogeneous material

- Basic substances included in GADSL should not allowed as wild cards. If substance is processed

as wild cards and it is included in GADSL due to revision of GADSL, data sheet should be revised

without wild cards and reapproved within 6 months after GADSL revision.

※ Since GADSL is continuously changed due to new regulation or revision about

chemical regulations , Confidential substance is rather recommended than wild cards for

better history control.

<Wild Cards List>

1. Flame retardant, not to declare

2. Further additives, not to declare

(60%)

(40%)

3. Impact modifier, not to declare

4. Inorganic ingredient, not to declare

5. Misc. not to declare

6. not yet specified, not to declare

7. Organic ingredient, not to declare

(60%)

(5%)

(35%)

8. Pigment portion, not to declare

9. Plasticizer, not to declare

[Wild cards allowed within 10% in homogeneous material]

20



● Gas / liquid

Gas / liquid not existed in final product (Ex: plating solvent, paint solvent, preprocessing cleaner) are

excluded when creating MDS. If gas / liquid are included in final product, input data as selecting

material classification 9.x (refrigerant, brake oil, lubricant, battery liquid, etc)

(20%)

(5%)

(66%)

(17%)

(10%)

(3%)

(70%)

(7%)

(2%)

Exclude water not included in final product

● Process chemicals

Process chemicals used in the production of a material/part that are not con-tained in the end

material/part must not be reported. But if they remain more than 0.1wt% in final materials,

application of chemical should be chosen.

If process chemicals contained over 0.1wt%, choose one of ‘Intended use’, Reaction residue’, ‘Impurity’

21



2.9 4

Heavy Metals and their Application Codes

- Lead (Pb), Cadimum (Cd), Mercury (Hg), Hexavalent Chrome (Cr

6+

) and their compounds should

not be used exceeding defined allowable value. And even small content of them should be input in

data sheet There is the threshold and exceptional permission of Heavy metals in HMC /KMC Material

Specification ‘MS 201-02’ (refer to 1.5 of this manual for heavy metal allowable value)

- Exceptionally, in some applications those heavy metals are still tolerated (refer to MS201-02 for

exceptional allowance). In this case proper application code should be choosen

※ Application code per material inquiry : http://mdsystem.com → IMDS Information Pages → Help

→ FAQ → ‘Is there any further explanation as to how to selected an Application ID?’ in ‘MDS

Ingredient Screen’

(Ex)

When prohibited material “Lead” is included, application code tab is created automatically in material information

Arbiary application code is automatically designated in the system. Creator should check and revise it to the proper code with reference to MS201-02 if wrong application code is selected.

22



2.10 Material Marking

- When materials composing component fall under material classification 5.x, material marking

information should be written to component details

※ It should be written after checking whether material is marked in actual component according

to HMC /KMC Material Specification ‘MS201-01 Marking of materials for automotive parts’

[Material Classification 5.x]

[Check whether material is acutally marked]

Select when material is marked

Select when material is not marked

Select when material marking is

Impossible due to shape limitation or surface character or weight

23



2.11 Contact Person Assignment

- Contact person of supplier should be assigned before transmitting MDS. Contact person should

be is assigned to the personnel who is responsible all business related to IMDS and can

communicate with Hyundai·Kia.

- When existing contact person is resigned / transfered, new personnel should be assigned among

employees presently involved with IMDS

Assign personnel who can be communication window related to

IMDS with Hyundai Kia

24



3.1

Sending MDS

3.1.1 Choice of Recipient

- Created MDS should be transmitted to the plant of model to which corresponding part

are applied and organization unit ID of our plants should be refered at below table.

(Example) Part applied to model produced in India Plant → 71405

Part applied to model produced in Georgia Plant → 119673

★ Please be carefule that MDS transmitted to wrong recipient will be rejected.

In addition, it is not valid even though it is sent to wrong recipient and approved

Company Model Plant Organz. ID Addressee Unit

HMC

All Domestic Plant, Czech

Plant(HMMC), India Plant

(HMI), Turkey Plant(HAOS)

71405

HYUNDAI MOTOR COMPANY

Alabama Plant (HMMA)

119671

HYUNDAI MOTOR ALABAMA

(HMMA)

KMC

All Domestic Plant,

Slovakia Plant(KMS)

71406

KIA MOTOR CORPORATION

Georgia Plant (KMMG)

119673

KIA MOTOR GEORGIA (KMMG)

● How to assign recipient add Addressee apply Addressee

(Continue at next page)

25


HyundaiㆍKia IMDS Guidance transmit MDS to designated addressee

3.1.2 Input Supplier Code

- When send MDS to Hyundai Kia, ‘Part / Item number’ and ‘Supplier Information’ should be

input to written MDS.

- Supplier Code : Vaatz code input

3.2 Feedback after Sending MDS

3.2.1 How to modify rejected MDS

- MDS should be revised and re-transmitted according to reject reason

- If any futher question about reject reason, please contact HMC / KMC contact person

(refer to ‘Summary’ of this instruction)

3.2.2 When part change occurs

- When part change occurs in already approved MDS (EO change, material change, addition / deletion of

sub-part, weight change (over 3% of total weight), color change, etc), MDS should be revised (version

-up with same ID) and appoved again

26

Hyundai - IMDS Information Pages - International Material Data

HyundaiㆍKia IMDS Guidance

Summary

1. Please be well-informed of basic IMDS instructions from following documents before read this guidance

2. This guidance is written based on IMDS Recommendations and if guidance and

Recommendations have discord, please follow this guidance.

3. MDS recipient should be based on corresponding vehicle manufacturing plant. MDS sent to other recipient is not valid even if it is accepted (refer to 3.1.1 of this guidance)

4. Please call to followings for any questions about system

- Hyundai, Kia Motor (reject reason, MDS acceptance criteria, ISIR related etc)

- IMDS Service Center (access authority / instructions / IMDS Recommendations etc)

- Table of Content -

1. 1 Backgrouds of IMDS

1.2 Timing of Sending MDS and Application Scope

1.4 Understanding Basic Property of MDS

1.5 4 Heavy Metals threshold / Material Marking

1.6 IMDS – ISIR Work Flow

Suppliers

Eco Technology

Research Team

(Hyundai, Kia) ISIR Supervision

Department

ISIR Final Approval

2.1 ID / Version Management

2. 2 Description and Part / Item No. Input

2.3 Material Classification Selection

2.4 Material Name Input

2.5 Parts Composition

2.6

2.7 Weight Tolerance of MDS

2.8 Basic Substance information

Confidential substances

2.9 4

2.10 Material Marking

2.11 Contact Person Assignment

3.1

3.2 Feedback after Sending MDS

Key Features

Related manuals

LG

GR-B662QVC

Frequently Answers and Questions

What is this document for?

What is IMDS?

What is a Material Data Sheet (MDS)?

What are the heavy metal regulations?

How do I submit my MDS?

What happens if my MDS is rejected?