Smawave Technology MGL6201A User Manual

MGL6201A
User Manual
Index
1 Getting Started................................................................................................................................. 4
1.1
Welcome to the Module.............................................................................................. 4
1.2
Computer Configuration Requirements......................................................................4
1.3
Logging In to the Web Management Page................................................................. 6
2
Overview..................................................................................................................................... 8
2.1
Viewing Current Connection...................................................................................... 8
2.2
Viewing LTE Status.................................................................................................... 8
2.3
Viewing WAN Status.................................................................................................. 8
3
Statistics...................................................................................................................................... 9
3.1
Viewing CPU Usage................................................................................................... 9
3.2
Viewing Memory Usage........................................................................................... 10
3.3
Viewing APN List..................................................................................................... 10
3.4
Viewing Throughput Statistics..................................................................................11
3.5
Viewing Device List..................................................................................................11
4
Update....................................................................................................................................... 12
4.1
Version Manager....................................................................................................... 12
Viewing Version Info........................................................................................................ 12
Version Upgrade................................................................................................................12
4.2
Auto upgrade.............................................................................................................13
5
Settings......................................................................................................................................14
5.1
Viewing the Device Information.............................................................................. 14
Viewing the Version Information......................................................................................15
Viewing LAN Status......................................................................................................... 15
5.2
Viewing Network...................................................................................................... 16
LTE Settings......................................................................................................................16
Scan Mode.........................................................................................................................18
APN Management.............................................................................................................19
PIN Management.............................................................................................................. 20
SIM Lock.................................................................................................................................. 22
LAN Setting...................................................................................................................... 22
DMZ Settings....................................................................................................................24
Static Route....................................................................................................................... 25
5.3
Parental Controls.......................................................................................................26
Parental Controls Manager............................................................................................... 26
Parental Controls List....................................................................................................... 26
5.4
Firewall..................................................................................................................... 27
Setting Firewall................................................................................................................. 27
MAC Filtering...................................................................................................................28
IP Filtering.........................................................................................................................31
URL Filtering.................................................................................................................... 34
Port Forwarding................................................................................................................ 36
UPnP................................................................................................................................. 39
DoS....................................................................................................................................39
5.6 VPN............................................................................................................................................. 40
5.7 IPv6............................................................................................................................................. 40
Status......................................................................................................................................... 40
IPv6 WAN Settings................................................................................................................... 41
IPv6 LAN Settings.................................................................................................................... 41
5.8 System......................................................................................................................................... 42
5.8.1 Maintenance..................................................................................................................... 42
Reboot............................................................................................................................... 42
Reset..................................................................................................................................42
Backup Configuration File................................................................................................43
Upload Configuration File................................................................................................ 43
5.8.2 TR069...............................................................................................................................44
5.8.3 Date & Time.....................................................................................................................45
5.8.4 DDNS...............................................................................................................................47
5.8.5 Diagnosis..........................................................................................................................48
Ping................................................................................................................................... 48
Traceroute..........................................................................................................................49
5.8.6 Port Mirror....................................................................................................................... 50
5.8.7 Syslog...............................................................................................................................51
Local..................................................................................................................................51
Network.............................................................................................................................51
5.8.8 WEB Setting.....................................................................................................................52
5.8.9 Account............................................................................................................................ 53
5.8.10 Logout............................................................................................................................ 54
6
FAQs..........................................................................................................................................54
1 Getting Started
1.1Welcome to the Module
This Module needs to be installed on a specific backplane, 12V power supply, and an external
antenna.The Module support B2/4/5/8/12/13/14/25/26/66/38/41/42/43/48/53.
And its tx power is 23±2.
Carefully read the following safety symbols to help you use your Module safely and correctly:
Additional information
Optional methods or shortcuts for an action
Potential problems or conventions that need to be specified
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
The customer does not have permission to modify the parameters of the device.
The device usage scenario is 20cm away from the human body.
No professional installation of equipment is required.
MGL6201A has built-in rich network protocols, integrates multiple industry standard interfaces, and
supports multiple drivers and software functions (for USB drivers under Windows 7/8 / 8.1 / 10, Linux,
Android and other operating systems), greatly expanding The application scope of MGL6201A, such as
CPE, router, data card, tablet PC, automotive, security and industrial PDA, etc.
1.2Computer Configuration Requirements
For optimum performance, make sure your computer meets the following requirements.
Item
Requirement
CPU
Pentium 500 MHz or higher
Memory
128 MB RAM or higher
Hard disk
50 MB available space
Operating system

Microsoft: Windows XP, Windows Vista, or Windows 7

Mac: Mac OS X 10.5 or higher
Display resolution
1024 x 768 pixels or higher
Browser

Internet Explorer 7.0 or later

Firefox 3.6 or later

Opera 10 or later

Safari 5 or later

Chrome 9 or later
1.3Logging In to the Web Management Page
Use a browser to log in to the web management page to configure and manage the Module.
The following procedure describes how to use a computer running Windows XP and Internet
Explorer 7.0 to log in to the web management page of the Module.
1.
Connect the Module properly.
2.
Launch Internet Explorer, enter http://192.168.1.1 in the address bar, and press Enter. As
shown in Figure 1-1.
Figure 1- 1
3.
Enter the user name and password, and click Log In.
4.
You can log in to the web management page after the password is verified. As shown in Figure
1-2.
Figure 1- 2
The default user name and password are both admin. If you want to view or configure
the CPE more, you should use the super account to log in to the web management page.
The default super user name is superadmin, and the password is admin.
To protect your CPE from unauthorized access, change the password after your first
login.
The CPE supports diagnostic function. If you encounter problems, please contact
customer service for the specific using method.
To ensure your data safety, it is recommended that you turn on the firewall, and
conserve your login and FTP password carefully.
2 Overview
2.1Viewing Current Connection
To view the current connection, perform the following steps:
Choose Overview;
In the Current Connection area, view the connection status, such as DL/UL Data Rate and
Online time. As shown in Figure 2-1.
Figure 2- 1
2.2Viewing LTE Status
To view the LTE network status, perform the following steps:
1. Choose Overview;
2. In the LTE Status area, view the information about Connect status, Mode, Cell ID, Signal
quality and so on. As shown in Figure 2-3.
2.3Viewing WAN Status
Figure 2- 3
To view the WAN status, perform the following steps:
1. Choose Overview;
2. In the WAN Status area, view the information about Connect Mode, IP, Subnet Mask,
DNS Server and so on. As shown in Figure 2-4.
Figure 2-4
3 Statistics
3.1Viewing CPU Usage
To view the CPU usage, perform the following steps:
1. Choose Statistics;
2. In the CPU Usage area, view the CPU usage information, such as Current CPU usage, Max
CPU usage, Min CPU usage. As shown in Figure 3-1.
3.2Viewing Memory Usage
Figure 3- 1
To view the memory usage, perform the following steps:
1. Choose Statistics;
2. In the Memory Usage area, view the memory usage information, such as Total memory,
Current memory usage, Max memory usage and Min memory usage. As shown in Figure
3-2.
3.3Viewing APN List
Figure 3- 2
To view the APN list, perform the following steps:
1. Choose Statistics;
2. In the APN List, view the information about APN information. As shown in Figure 3-3.
Figure 3- 3
3.4Viewing Throughput Statistics
To view the Throughput Statistics, perform the following steps:
1. Choose Statistics;
2. In the Throughput Statistics area, view the throughput statistics, such as APN throughput
and LAN throughput.
3. In this area, also you can choose and click the button Reset to empty the throughput
statistics. As shown in Figure 3-4.
3.5Viewing Device List
Figure 3- 4
To view the device list, perform the following steps:
Choose Statistics;
In the Device List area, view the device information which connect to the CPE, such as
Device name, Mac address, IP address and Lease time. As shown in Figure 3-5.
Figure 3- 5
4 Update
4.1 Version Manager
This function enables you to upgrade the software version of the CPE to the latest version. It is
recommended that you upgrade the software because the new version, certain bugs have been
fixed and the system stability is usually improved.
Viewing Version Info
To view the version info, perform the following steps:
1. Choose Update>Version Manager.
2. In the Version Info area, you can view the product name and software version. As shown in
Figure 4-1.
Version Upgrade
Figure 4- 1
To perform an upgrade successfully, connect the CPE to your computer through a network cable,
save the upgrade file on the computer, and make sure the CPE is not connected to anything other
than a power adapter and the computer.
To perform an upgrade, perform the following steps:
1. Choose Update>Version Manager.
2. In the Version Upgrade area, click Browse. In the displayed dialog box, select the target
3.
4.
5.
software version file.
Click Open. The dialog box choses. The save path and name of the target software version
file are displayed in the Update file field.
Click Submit.
The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the
new software version. As shown in Figure 4-2.
During an upgrade, do not power off the CPE or disconnect it from the
computer.
4.2Auto upgrade
Figure 4-2
To perform a ftp auto upgrade successfully, make sure the CPE is connected to the Internet.
To perform a ftp auto upgrade, perform the following steps:
Choose Update>Auto upgrade.
Enable auto upgrade.
If you want to check new firmware after connect to Internet, you need to
enable the item of Check new firmware after connect to Internet.
Set a ftp address to the Upgrade folder box.
Set Version file.
Set User name and Password.
Set the Interval of checking new firmware.
Set Start time.
Set Random time.
Click Submit. As shown in Figure 4-3.
The CPE will automatically upgrade according to the setting. During an upgrade,
do not disconnect the power supply or operate the CPE.
Figure 4- 3
5 Settings
5.1 Viewing the Device Information
To view the System Information, perform the following steps:
Choose Settings;
In the System Information area, view the system status, such as Running time. As shown in
Figure 5-1.
Figure 5- 1
Viewing the Version Information
To view the Version Information, perform the following steps:
1. Choose Settings;
2. In the Device Information area, view the device information, such as Product name, Product
Module, Hardware Version, Software version, UBoot version and CPE SN . As shown in
Figure 5-2.
Viewing LAN Status
Figure 5- 2
To view the LAN status, perform the following steps:
Choose Settings;
In the LAN Status area, view the LAN status, such as Mac address, IP address and Subnet
mask. As shown in Figure 5-4.
Figure 5- 4
5.2Viewing Network
Network Mode
To set the network mode, perform the following steps:
Choose Network >WAN Settings;
In the Network Mode area, select a mode between NAT and ROUTER;
Click Submit. As shown in Figure 5-5.
Figure 5- 5
LTE Settings
Settings
To set the LTE network, perform the following steps:
1. Choose Network >LTE Settings;
2. In the Settings area, you can set the configuration of LTE network;
3. In the Status area, you can view the LTE network connect status, such as Frequency, RSSI,
RSRP, RSRQ, CINR, SINR, Cell ID and so on. As shown in Figure 5-7.
Connect Method Setting
Figure 5- 7
To set the connect method, perform the following steps:
1. Choose Network > LTE Settings;
2. In the Setting area, Select a connect method between Auto and Manual. As shown in Figure
5-8.
Figure 5- 8
Auto Connect LTE Network
To set the CPE automatically connect to the internet, perform the following steps:
1. Choose Network > LTE Settings;
2. In the Setting area, set the connect method as Auto, when the LTE network is ready, the CPE
will be connected automaticity. As shown in Figure 5-9.
Figure 5- 9
Manual Connect Mobile Network
To set the mobile network manual connect to the internet, perform the following steps:
1.
2.
Choose Network > LTE Settings;
In the Setting area, set the connect method as Manual, when the LTE network is ready, you
can set the CPE connect to the LTE network or disconnect from the LTE network. As shown
in Figure 5-10.
Scan Mode
Figure 5- 10
To set the lte network scan mode, perform the following steps:
choose Network>Scan mode;
You can choose full mode, a band the CPE supported
Click Submit.
Setting Frequency (Earfcn)
To set the frequency, perform the following steps:
1 Choose Network>Scan Mode.
2 In the Scan Mode area, choose Frequency Lock.
3 In the Frequency Lock area, you can choose a band, then click Add list to
choose a Earfcn Number.
4 Click Submit. As shown in Figure 5-11.
APN Management
Figure 5- 11
To set and manage APN, perform the following steps:
Choose Network>APN Management.
In the APN Management area, you can set the APN.
Choose a APN number which you want to set.
In the APN Setting area you can set the APN parameters, such as enable or disable the apn,
apn name, username, password and so on.
If you want set a APN as default gateway, you should check that is enabled.
Click Submit. As shown in Figure 5-12.
PIN Management
Figure 5- 12
To manage the PIN, you can perform the following operations on the PIN Management page:
 Enable or disable the PIN verification.
 Verify the PIN.
 Change the PIN.
 Set automatic verification of the PIN. As shown in Figure 5-13
Figure 5- 13
Viewing the Status of the USIM Card
To view the status of the USIM card, perform the following steps:
1 Choose Network >PIN Management.
2 View the status of the USIM card in the USIM card status field.
Enabling PIN Verification
To enable PIN verification, perform the following steps:
1 Choose Network >PIN Management.
2 Set PIN verification to Enable.
3 Enter the PIN (4 to 8 digits) in the Enter PIN box.
4 Click Submit.
Disabling PIN Verification
To disable PIN verification, perform the following steps:
1 Choose Network >PIN Management.
2 Set PIN verification to Disable.
3 Enter the PIN (4 to 8 digits) in the Enter PIN box.
4 Click Submit.
Verifying the PIN
If PIN verification is enabled but the PIN is not verified, the verification is required. To verify the
PIN, perform the following steps:
1 Choose Network >PIN Management.
2 Enter the PIN (4 to 8 digits) in the PIN box.
3 Click Submit.
Changing the PIN
The PIN can be changed only when PIN verification is enabled and the PIN is verified.
To change the PIN, perform the following steps:
1 Choose Network>PIN Management.
2 Set PIN verification to Enable.
3 Set Change PIN to Enable.
4 Enter the current PIN (4 to 8 digits) in the PIN box.
5 Enter a new PIN (4 to 8 digits) in the New PIN box.
6 Repeat the new PIN in the Confirm PIN box.
7 Click Submit.
Setting Automatic Verification of the PIN
You can enable or disable automatic verification of the PIN. If automatic verification is enabled, the
CPE automatically verifies the PIN after restarting. This function can be enabled only when PIN
verification is enabled and the PIN is verified.
To enable automatic verification of the PIN, perform the following steps:
1.
Choose Network > PIN Management.
2.
Set Pin verification to Enable.
3.
Set Remember my PIN to Enable.
4.
Click Submit.
Verifying the PUK
If PIN verification is enabled and the PIN fails to be verified for three consecutive times, the PIN will
be locked. In this case, you need to verify the PUK and change the PIN to unlock it.
To verify the PUK, perform the following steps:
Choose Network> PIN Management.
Enter the PUK in the PUK box.
Enter a new PIN in the New PIN box.
Repeat the new PIN in the Confirm PIN box.
Click Submit.
SIM Lock
If you want to connect a specify network, and the CPE can’t connect other network, you can set a
SIM lock.
To set the SIM lock, perform the following steps:
1. Choose Network>SIM Lock.
2. Enter the PLMN in the PLMN box.
3. Click Submit. As shown in Figure 3-9.
LAN Setting
Figure 3- 9
Setting LAN Host Parameters
By default, the IP address is 192.168.0.1 with a subnet mask of 255.255.255.0. You can change the
host IP address to another individual IP address that is easy to remember. Make sure that IP
address is unique on your network. If you change the IP address of the CPE, you need to access
the web management page with the new IP address.
To change the IP address of the CPE, perform the following steps:
1. Choose Network>LAN Settings.
2. In the LAN Host Settings area, set IP address and subnet mask.
3. In the DHCP Setting area, set the DHCP server to Enable.
4. Click Submit. As shown in Figure 5-14.
Figure 5- 14
Configuration the DHCP Server
DHCP enables individual clients to automatically obtain TCP/IP configuration when the server
powers on. You can configure the CPE as a DHCP server or disable it. When configured as a DHCP
server, the CPE automatically provides the TCP/IP configuration for the LAN clients that support
DHCP client capabilities. If DHCP server services are disabled, you must have another DHCP server
on your LAN, or each client must be manually configured.
To configure DHCP settings, perform the following steps:
1.
Choose Network Setting > LAN Settings.
2.
3.
Set the DHCP server to Enable.
Set Start IP address.
This IP address must be different from the IP address set on the LAN Host Settings area, but
they must be on the same network segment.
4.
Set End IP address.
This IP address must be different from the IP address set on the LAN Host Settings area, but
they must be on the same network segment.
5.
Set Lease time.
Lease time can be set to 1 to 10,080 minutes. It is recommended to retain the default
value.
6.
Click Submit. As shown in Figure 5-15.
Figure 5- 15
DMZ Settings
If the demilitarized zone (DMZ) is enabled, the packets sent from the WAN are directly sent to a
specified IP address on the LAN before being discarded by the firewall.
To set DMZ, perform the following steps:
1.
2.
3.
4.
Choose Network > DMZ Settings.
Set DMZ to Enable.
(Optional) Set ICMP Redirect to Enable.
Set Host address.
This IP address must be different from the IP address set on the LAN Host
Settings page, but they must be on the same network segment.
5.
Click Submit. As shown in Figure 5-18.
Figure 5- 18
Static Route
Add Static Route
To add a static route, perform the following steps:
Choose Network Setting>Static Route.
Click Add list.
Set the Dest IP address and Subnet mask.
Select an Interface from the drop-down list.
If you select LAN as the interface, you need set a Gateway.
Click Submit. As shown in Figure 5-19.
Modify Static Route
Figure 5- 19
To modify an access restriction rule, perform the following steps:
1. Choose Firewall>Static Route.
2. Choose the item to be modified, and click Edit.
3. Repeat steps 3 through 5 in the previous procedure.
4. Click Submit. As shown in Figure 5-20.
Delete Static Route
Figure 5- 20
To delete a static route, perform the following steps:
Choose Firewall>Static Route.
Choose the item to be deleted, and click Delete.
5.3 Parental Controls
This page describes how to set the Parental Controls. If you enable or disable the Parental
Controls, you can modify the configuration.
Parental Controls Manager
Choose Parental Controls Manager, Choose Enable ,and then click Submit Enabled the Choose
Parental function. As shown in Figure 5-4-1.
Figure 5-4-1.
Parental Controls List
This page is set the Parental Controls List. If this function is enabled, you can add some users. If
someone in this List , he was forbidden from the Internet. If you want to allow him to access the
Internet, you can remove it from this Parental Controls List. As shown in Figure 5-4-2、5-4-3
Figure 5-4-2
Figure 5-4-3
5.4 Firewall
Setting Firewall
This page describes how to set the firewall. If you enable or disable the firewall, you can modify
the configuration.
To set the firewall, perform the following steps:
Choose Firewall>Firewall Setting.
Choose Enable or Disable to modify the configuration.
Click Submit. As shown in Figure 5-30.
Figure 5- 30
If you choose enable the firewall, you can modify the configuration about firewall, such as Mac
filter, IP filter, URL filter and so on. If you choose disable, you can’t modify any configurations
about the firewall.
MAC Filtering
This page enables you to configure the MAC address filtering rules.
Enabling MAC Filter
To enable MAC address filter, perform the following steps:
1. Choose Firewall>MAC Filtering
2. Set MAC filtering to Enable.
3. Click Submit. As shown in Figure 5-31.
Disabling MAC Filter
Figure 5- 31
To disable MAC address filter, perform the following steps:
1. Choose Firewall>MAC Filtering
2. Set MAC filtering to Disable.
3. Click Submit. As shown in Figure 5-32.
Figure 5- 32
Setting Allow access network within the rules
To set allow access network within the rules, perform the following steps:
1. Choose Firewall>MAC Filtering.
2. Set Allow access network within the rules.
3. Click Submit. As shown in Figure 5-33.
Figure 5- 33
Setting Deny access network within the rules
To set deny access network within the rules, perform the following steps:
1. Choose Firewall>MAC Filtering.
2. Set Deny access network within the rules.
3. Click Submit. As shown in Figure 5-34.
Figure 5- 34
Adding MAC Filtering rule
To add a MAC filtering rule, perform the following steps:
Choose Firewall>MAC Filtering.
Click Add list.
Set MAC address.
Click Submit. As shown in Figure 5-35.
Figure 5- 35
Modifying MAC Filtering rule
To modify a MAC address rule, perform the following steps:
1. Choose Firewall>MAC Filtering.
2. Choose the rule to be modified, and click Edit.
3. Set MAC address.
4.
Click Submit. As shown in Figure 5-36.
Figure 5- 36
Deleting MAC Filtering rule
To delete a MAC address filter rule, perform the following steps:
Choose Firewall>MAC Filtering.
Choose the rule to be deleted, and click Delete. As shown in Figure 5-37.
IP Filtering
Figure 5- 37
Data is filtered by IP address. This page enables you to configure the IP address filtering rules.
Enabling IP Filtering
To enable IP Filtering, perform the following steps:
1. Choose Firewall>IP Filtering.
2. Set IP Filtering Enable.
3.
Click Submit. As shown in Figure 5-38.
Disabling IP Filtering
Figure 5- 38
To disable IP Filtering, perform the following steps:
1. Choose Firewall>IP Filtering.
2. Set IP Filtering Disable.
3. Click Submit. As shown in Figure 5-39.
Figure 5- 39
Setting Allow access network outside the rules
To set allow access network, perform the following steps:
1. Choose Firewall>IP Filtering.
2. Set Allow access network outside the rules.
3. Click Submit. As shown in Figure 5-40.
Figure 5- 40
Setting Deny access network outside the rules
To set allow access network, perform the following steps:
1. Choose Firewall>IP Filtering.
2. Set Deny access network outside the rules.
3.
Click Submit. As shown in Figure 5-41.
Adding IP Filtering rule
Figure 5- 41
Add an IP address filtering rule, perform the following steps:
1. Choose Firewall>IP Filtering.
2. Click Add list.
3. Set Service.
4. Set Protocol.
5. In the Source IP Address Range box, enter the source IP address or IP address segment to
be filtered.
6. In the Source port range box, enter the source port or port segment to be filtered.
7. In the Destination IP Address Range box, enter the destination IP address or IP address
segment to be filtered.
8. In the Destination port Range box, enter the destination port or port segment to be
filtered.
9. In the Status box, choose a status the rule will be executed.
10. Click Submit. As shown in Figure 5-42.
Modifying IP Filtering rule
Figure 5- 42
To modify an IP filtering rule, perform the following steps:
1.
2.
3.
4.
Choose Firewall > IP Filtering.
Choose the rule to be modified, and click Edit.
Repeat steps 3 through 9 in the previous procedure.
Click Submit. As shown in Figure 5-43.
Figure 5- 43
Deleting IP Filtering rule
To delete an IP address filtering rule, perform the following steps:
1.
2.
Choose Firewall > IP Filtering.
Choose the rule to be deleted, and click Delete. As shown in Figure 5-44.
URL Filtering
Figure 5- 44
Data is filtered by uniform resource locator (URL). This page enables you to configure URL
filtering rules.
Enabling URL Filtering
To enable URL Filtering, perform the following steps:
3. Choose Firewall>URL Filtering.
4. Set URL Filtering to Enable.
5. Click Submit. As shown in Figure 5-45.
Disabling URL Filtering
Figure 5- 45
To disable URL Filtering, perform the following steps:
1. Choose Firewall>URL Filtering.
2. Set URL Filtering to Disable.
3. Click Submit. As shown in Figure 5-46.
Figure 5- 46
Adding URL Filtering list
To add a URL filtering list, perform the following steps:
Choose Firewall>URL Filtering.
Click Add list.
Set URL.
Click Submit. As shown in Figure 5-47.
Modify URL Filtering list
Figure 5- 47
To modify a URL filtering rule, perform the following steps:
1. Choose Firewall>URL Filtering.
2. Choose the rule to be modified, and click Edit.
3. Set URL address.
4. Click Submit. As shown in Figure 5-48.
Deleting URL Filtering list
Figure 5- 48
To delete a URL list, perform the following steps:
1. Choose Firewall>URL Filtering.
2. Choose the item to be deleted, and click Delete. As shown in Figure 5-49.
Figure 5- 49
Port Forwarding
When network address translation (NAT) is enabled on the CPE, only the IP address on the WAN side
is open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for
example, work as an FTP server), port forwarding is required so that all accesses to the external
server port from the Internet are redirected to the server on the LAN.
Adding Port Forwarding rule
To add a port forwarding rule, perform the following steps:
Choose Firewall > Port Forwarding.
Click Add list.
Set Service.
Set Protocol.
Set Remote port range.
The port number ranges from 1 to 65535.
Set Local host.
This IP address must be different from the IP address that is set on the LAN
Host Settings page, but they must be on the same network segment.
Set Local port.
The port number ranges from 1 to 65535.
Click Submit. As shown in Figure 5-50.
Figure 5- 50
Modifying Port Forwarding rule
To modify a port forwarding rule, perform the following steps:
1.
Choose Firewall > Port Forwarding.
2.
Choose the item to be modified, and click Edit.
3.
Repeat steps 3 through7 in the previous procedure.
4.
Click Submit. As shown in Figure 5-51.
Figure 5- 51
Deleting Port Forwarding rule
To delete a port forwarding rule, perform the following steps:
Choose Firewall > Port Forwarding.
Choose the item to be deleted, and click Delete. As shown in Figure 5-52.
Figure 5- 52
Access Restriction
Figure 5-53
Add Access Restriction
To add a access restriction rule, perform the following steps:
1. Choose Security>Access Restriction.
2. Click Add list.
3. Set Access Restriction to Enable.
4. Set Access Restriction Name.
5. Set Device MAC address or IP address.
6. Set Weekdays and time.
7. Click Submit.
Modify Access Restriction
To modify a access restriction rule, perform the following steps:
1. Choose Security>Access Restriction.
2. Choose the item to be modified, and click Edit.
3. Repeat steps 4 through 6 in the previous procedure.
4.
Click Submit.
Delete Access Restriction
To delete a access restriction rule, perform the following steps:
1. Choose Security>Access Restriction.
2. Choose the item to be deleted, and click Delete.
UPnP
On this page, you can enable or disable the Universal Plug and Play (UPnP) function.
To enable UPnP, perform the following steps:
1. Choose Firewall > UPnP.
2. Set UPnP to Enable.
3. Click Submit. As shown in Figure 5-54.
DoS
Figure 5- 54
On this page, you can enable or disable the Denial of service (DoS) function.
1 Choose Firewall > DoS.
2 Set UPnP to Enable.
3 Click Submit. As shown in Figure 5-55.
Figure 5- 55
5.6 VPN
This function enables you to connect the virtual private network (VPN).
To connect the VPN, perform the following steps:
Choose VPN.
In the VPN Settings area, enable VPN.
Select a protocol from Protocol drop-down list.
Enter Username and Password.
Click Submit.
You can view the status in VPN Status area. As shown in Figure 5-55.
Figure 5- 55
5.7 IPv6
Internet Protocol version 6 (IPv6) is the most recent version of the Internet Protocol (IP). Every
device on the Internet is assigned a unique IP address for identification and location definition.
Status
The status page shows IPv6 information. As shown in Figure 5-56.
Figure 5-56
IPv6 WAN Settings
In this page, user can enable or disable IPv6 function. Meanwhile, user can set WAN Connection
Type and the type of DNS.As shown in Figure 5-27
Figure 5-57
IPv6 LAN Settings
In this page, user can chose the AutoConfiguration Type. As shown in Figure 5-58.
Figure 5-58
5.8 System
5.8.1 Maintenance
Reboot
This function enables you to restart the CPE. Settings take effect only after the CPE restarts. To
restart the CPE, perform the following steps:
1. Choose System>Maintenance.
2. Click Reboot. As shown in Figure 5-59.
The CPE then restarts.
Reset
Figure 5- 59
This function enables you to restore the CPE to its default settings.
To restore the CPE, perform the following steps:
1. Choose System>Maintenance.
2. Click Factory Reset. As shown in Figure 5-60.
The CPE is then restored to its default settings.
Figure 5- 60
Backup Configuration File
You can download the existing configuration file to back it up. To do so:
1. Choose System>Maintenance.
2. Click Download on the Maintenance page.
3. In the displayed dialog box, select the save path and name of the configuration file to be
backed up.
4. Click Save. As shown in Figure 5-61.
The procedure for file downloading may vary with the browser you are using.
Figure 5- 61
Upload Configuration File
You can upload a backed up configuration file to restore the CPE. To do so:
1. Choose System>Maintenance.
2. Click Browse on the Maintenance page.
3. In the displayed dialog box, select the backed up configuration file.
4. Click Open.
5. The dialog box choses. In the box to be right of Configuration file, the save path and name
of the backed up configuration file are displayed.
6. Click Upload. As shown in Figure 5-62.
The CPE uploads the backed up configuration file. The CPE then automatically restarts.
Figure 5- 62
5.8.2 TR069
TR-069 is a standard for communication between CPEs and the auto-configuration server (ACS). If
your service provider uses the TR069 automatic service provision function, the ACS automatically
provides the CPE parameters. If you set the ACS parameters on both the CPE and ACS, the network
parameters on the CPE are automatically set using the TR-069 function, and you do not need to set
other parameters on the CPE.
To configure the CPE to implement the TR-069 function, perform the following steps:
1.
Choose System>TR069.
2.
Set acs URL source. There are two methods, such as URL and DHCP.
3.
In the ACS URL box, enter the ACS URL address.
4.
Enter ACS user name and password for the CPE authentication.
To use the CPE to access the ACS, you must provide a user name and
password for authentication. The user name and the password must be the
same as those defined on the ACS.
5.
If you set Periodic inform to Enable, set Periodic inform interval.
6.
Set connection request user name and password.
7.
Click Submit. As shown in Figure 7-5.
5.8.3 Date & Time
Figure 5- 63
You can set the system time manually or synchronize it with the network. If you select Sync from
network, the CPE regularly synchronizes the time with the specified Network Time Protocol (NTP)
server. If you enable daylight saving time (DST), the CPE also adjusts the system time for DST.
To set the date and time, perform the following steps:
1.
Choose System > Date & Time.
2.
Select Set manually.
3.
Set Local time or click Sync to automatically fill in the current local system time.
4.
Click Submit. As shown in Figure 5-64.
Figure 5-64
To synchronize the time with the network, perform the following steps:
1.
Choose System > Date & Time.
2.
Select Sync from network.
3.
From the Primary NTP server drop-down list, select a server as the primary server for time
synchronization.
4.
From the Secondary NTP server drop-down list, select a server as the IP address of the secondary
server for time synchronization.
5.
If you don’t want to use other NTP server, you need to enable Optional ntp server, and set a
server IP address.
6.
Set Time zone.
7.
Click Submit. As shown in Figure 5-65.
To set DST, perform the following steps:
1.
Choose System>Date&Time.
2.
Set DST enable.
3.
Set Start Time and End Time.
4.
Click Submit. As shown in Figure 5-66.
Figure 5- 65
Figure 5-66
The CPE will automatically provide the DST time based on the time zone.
5.8.4 DDNS
Dynamic Domain Name Server (DDNS) service is used to map the user's dynamic IP address to a fixed
DNS service.
To configure DDNS settings, perform the following steps:
1.
Choose System > DDNS.
2.
Set DDNS to Enable.
3.
In Service provider, choose DynDNS.org or oray.com.
4.
Enter Domain name and Host name. For example, if the domain name provided by your service
provider is test.customtest.dyndns.org, enter customtest.dyndns.org as Domain name, and test
as Host name.
5.
Enter User name and Password.
6.
Click Submit. As shown in Figure 5-67.
Figure 5-67
5.8.5 Diagnosis
If the CPE is not functioning correctly, you can use the diagnosis tools on the Diagnosis page to
preliminarily identify the problem so that actions can be taken to solve it.
Ping
If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To
do so:
Choose System>Diagnosis.
In the Method area, select Ping.
Enter the domain name in the Target IP or domain field, for example,
www.google.com.
Set Packet size and Timeout.
Set Count.
Click Ping. As shown in Figure 5-68.
Wait until the ping command is executed. The execution results are displayed in the Results box.
Traceroute
Figure 5-68
If the CPE fails to access the Internet, run the Traceroute command to preliminarily identify the
problem. To do so:
1.
Choose System>Diagnosis.
2.
In the Method area, select Traceroute.
3.
Enter the domain name in the Target IP or domain field. For example, www.google.com.
4.
Set Maximum hops ad Timeout.
5.
Click Traceroute. As shown in Figure 5-69
Wait until the traceroue command is executed. The execution results are displayed in the Results
box.
5.8.6 Port Mirror
Figure 5-69
Port mirroring is used on a network switch to send a copy of network packets seen on one
switch port.To do so:
1.
Choose System>Port Mirror.
2.
Enable Port Mirror.
3.
Select the WAN Interface which you want a copy.
4.
Type the Monitor IP, where the copy will send to.
5.
Click Sbumit. As shown in Figure 5-70.
Figure 5-70
5.8.7 Syslog
The syslog record user operations and key running events.
Local
To set the syslog to local, perform the following steps:
1.
Choose System>Syslog.
2.
In the Setting area, set the method to Local.
3.
In the Level drop-down list, select a log level.
4.
Click Submit. As shown in Figure 5-71.
Figure 5-71
Viewing local syslog
To view the local syslog, perform the following steps:
In the Keyword box, set a keyword.
Click Pull, the result box will display.
Network
To set the syslog to network, perform the following steps:
1.
Choose System>Syslog.
2.
In the Setting area, set the method to Network.
3.
In the Level drop-down list, select a log level.
4.
In the Forward IP address box, set a IP address.
5.
Click Submit. As shown in Figure
5-72.
The syslog will transmit to some client to display through network.
5.8.8 WEB Setting
Figure 5-72
To configure the parameters of WEB, perform the following steps:
1. Choose System> WEB Setting.
2. Set HTTP enable. If you set HTTP disable, you will can’t login the web management page
with the HTTP protocol from WAN side.
3. Set HTTP port. If you want to change the login port, you can set a new port in the box, the
default HTTP port is 80.
4. Set HTTPS enable. If you want to login the web management page with the HTTPS protocol
from WAN side, you need to enable the HTTPS.
5. If you want to login the web management page form the WAN, you need to Enable
Allowing login from WAN.
6. Set the HTTPS port.
7. Click Submit. As shown in Figure 5-73.
5.8.9 Account
Figure 5-73
This function enables you to change the login password of the user. After the password changes,
enter the new password the next time you login.
To change the password, perform the following steps:
1. Choose System>Account.
2. Select the user name, if you want to change the password of normal user, you need to set
Enable User enable.
3. Enter the current password, set a new password ,and confirm the new password.
4. New password and Confirm password must contain 5 to 15 characters.
5. Click Submit. As shown in Figure 5-74.
5.8.10 Logout
Figure 5-74
To logout the web management page, perform the following steps:
Choose System and click Logout
It will back to the login page.
6 FAQs
The POWER indicator does not turn on.
 Make sure that the power cable is connected properly and the Module is powered on.
 Make sure that the power adapter is compatible with the Module.
Fails to Log in to the web management page.
 Make sure that the Module is started.
 Verify that the Module is correctly connected to the computer through a network cable. If
the problem persists, contact authorized local service suppliers.
The Module fails to search for the wireless network.



Check that the power adapter is connected properly.
Check that the Module is placed in an open area that is far away from obstructions, such as
concrete or wooden walls.
Check that the Module is placed far away from household electrical appliances that generate
strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes.
If the problem persists, contact authorized local service suppliers.
The power adapter of the Module is overheated.
The Module will be overheated after being used for a long time. Therefore, power off the
Module when you are not using it.
Check that the Module is properly ventilated and shielded from direct sunlight.
The parameters are restored to default values.
If the Module powers off unexpectedly while being configured, the parameters may be
restored to the default settings.
After configuring the parameters, download the configuration file to quickly restore the
Module to the desired settings.
FCC Certification Requirements.
According to the definition of mobile and fixed device is described in Part 2.1091(b), this
device is a mobile device.
And the following conditions must be met:
1. This Modular Approval is limited to OEM installation for mobile and fixed applications only.
The antenna installation and operating configurations of this transmitter, including any applicable
source-based time- averaging duty factor, antenna gain and cable loss must satisfy MPE categorical
Exclusion Requirements of 2.1091.
2. The EUT is a mobile device; maintain at least a 20 cm separation between the EUT and the
user’s body and must not transmit simultaneously with any other antenna or transmitter.
3. A label with the following statements must be attached to the host end product: This device
contains FCC ID: 2AU8HMGL6201A.
4.To comply with FCC regulations limiting both maximum RF output power and human
exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed:
❒ <4.22dBi
5. This module must not transmit simultaneously with any other antenna or transmitter
6. The host end product must include a user manual that clearly defines operating
requirements and conditions that must be observed to ensure compliance with current FCC RF
exposure guidelines.
For portable devices, in addition to the conditions 3 through 6 described above, a separate
approval is required to satisfy the SAR requirements of FCC Part 2.1093
If the device is used for other equipment that separate approval is required for all other
operating configurations, including portable configurations with respect to 2.1093 and different
antenna configurations.
For this device, OEM integrators must be provided with labeling instructions of finished
products. Please refer to KDB784748 D01 v07, section 8. Page 6/7 last two paragraphs:
A certified modular has the option to use a permanently affixed label, or an electronic label.
For a permanently affixed label, the module must be labeled with an FCC ID - Section 2.926 (see 2.2
Certification (labeling requirements) above). The OEM manual must provide clear instructions
explaining to the OEM the labeling requirements, options and OEM user manual instructions that
are required (see next paragraph).
For a host using a certified modular with a standard fixed label, if (1) the module’s FCC ID is
not visible when installed in the host, or (2) if the host is marketed so that end users do not have
straightforward commonly used methods for access to remove the module so that the FCC ID of
the module is visible; then an additional permanent label referring to the enclosed
module:“Contains Transmitter Module FCC ID: 2AU8HMGL6201A” or “Contains FCC ID:
2AU8HMGL6201A” must be used. The host OEM user manual must also contain clear instructions
on how end users can find and/or access the module and the FCC ID.
The final host / module combination may also need to be evaluated against the FCC Part 15B
criteria for unintentional radiators in order to be properly authorized for operation as a Part 15
digital device.
The user’s manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. In cases where the manual is
provided only in a form other than paper, such as on a computer disk or over the Internet, the
information required by this section may be included in the manual in that alternative form,
provided the user can reasonably be expected to have the capability to access information in that
form.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
To ensure compliance with all non-transmitter functions the host manufacturer is responsible
for ensuring compliance with the module(s) installed and fully operational. For example, if a host
was previously authorized as an unintentional radiator under the Declaration of Conformity
procedure without a transmitter certified module and a module is added, the host manufacturer is
responsible for ensuring that the after the module is installed and operational the host continues to
be compliant with the Part 15B unintentional radiator requirements.
">