FOS SOLO User Manual
Add to My manuals20 Pages
FOS Technologies Ltd. Solo
The Solo is a battery-powered, wireless DMX luminaire with a built-in rechargeable lithium-ion battery that can support 4.0 hours of working at full-color mode. It features 3 super bright RGBWA+UV hex color LEDs, which can create more vivid color-changing effects, and a wide range of color temperatures.
The Solo can be controlled with an infrared remote controller, which can help users to achieve all working functions. This highly compact luminaire has very small dimensions that can be used not only as an uplight but also as a truss warmer. Its tilt can manually move 25 degrees when needed. It is absolutely an ideal tool for mobile DJ or Band, wedding, exhibitions, ball room and hotel banquet halls etc.
advertisement
User’s Manual
Battery Powered
Wireless DMX
Luminaire
USER’S MANUAL
FOS Technologies Ltd.
--------------------------------------------------------------------------------------------------------
Before you operate this fixture read the manual carefully. Always make sure to include the manual if you pass/rent/sell the fixture to another user.
User’s Manual
TABLE OF CONTENT
1. Warning ………………………….……….……………………………………………….…………………………………………..2
1.1 Safety Instructions ………………………………………………….……………………………………………………….2
1.2 Rigging …………………………………………………………………………………………………………………….….…3
2. Product Introduction … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … . … … … … … 3
2.1 Items Included in the Package …………………………………….…….…….……..……………………..……..........3
2.2 Product Overview…………………………………………………………………….……………………………………….3
2.3 Fixture Temperature ………………………………………..………………….………..…….……………..……………….5
2.4 Storing the Fixture ……………………………….........……………………….…….……….………………………………5
2.5 Mounting ………………………………………………………………………………………….………..……………………6
2.6 Specifications………………………………………………..………………………………….………..…………………… 7
3. Battery Charging ………………………………………………………………………………………….…………………………8
4. Product Setup ………….…………....……………………………………………………………...…………………………………8
4.1 OLED Display Setup …………………………………………………………………………………………..…………………8
4.2 Menu Navigation ………………………………………………………………………………………..………………….9
4.3 DMX Addressing ………………………………………………………………………….…………………………………9
4.4 Wireless DMX Setup ……………………………………………………………………………………………………………10
5. Operation …………………………………………………………………………………………………………………………….11
5.1 DMX Control Mode………………………………………………………………..…………….………………………………11
5.2 Auto Run Mode …………………………..……………………………………………………………………………………12
5.3 Sound Mode…………………………………………..……………………………………………………………………….12
5.4 Cusomized Colors………………………..………………………………………………………………………………………13
5.5 IR Remote Control ……………..………………………………………………………………………………………………13
6. Maintenance ………………………………………………………………………..………………………………….…14
6.1 General Maintenance ………………………………………………………………………………………………………14
6.2 Fuse Replacement ………………………………………………………………….………………………………………15
7. Warranty ………………………………………………………………………..……………………………………………16
1
User’s Manual
1. WARNING
1.1 Safety Instructions
This product guide contains important information about the safe installation and use of this product. Please read and follow these instructions carefully and keep this manual in a safe place for future reference.
When unpacking and before disposing of the carton, check there is no transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The product is for indoor use only. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids. The product is not designed or intended to be mounted directly on to inflammable surfaces.
The product is only intended for installation, operation and maintenance by qualified personnel.
The product must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not directly look into the led. It can cause harm to your eyes. Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output.
Do not attempt to dismantle and/or modify the product in any way.
Electrical connection must only be carried out by qualified personnel.
Before charging the fixture, ensure that the voltage and frequency of power supply match the power requirements of the product.
Do not directly look into the light beam. It can cause harm to your eyes. Do not look at the led with a magnifying glass or any other optical instrument that may concentrate the light output.
A rechargeable lithium ion battery is built inside this fixture. Please avoid bumping or plunging, it may cause fire or explosion. Never store the battery when fully drained. Always recharge immediately when empty.
Make sure to fully charge all fixtures before storing them. Partially charged batteries will lose capacity. Fully recharge every 6 months if not used.
When charging fixtures in flight case, always charge with the case open. It is recommended to charge at a temperature between 0°C and 35°C.
Please make sure the battery will be disposed of properly according to your local law when it runs out of its life, so that to protect the environment.
This product is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
If this fixture is operated in any other way other than the one said in this manual, this device may suffer damages and thus the warranty becomes void.
Always switch off the fixture when it is not in use or before cleaning it or before attempting any maintenance work.
2
User’s Manual
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the fixture.
1.2 Rigging
Concerning rigging, trussing for this fixture, please follow the European and national guidelines.
Only the qualified technicians are allowed for the device installation,
The fixture must never be mounted for a possible swinging position, and a safety cord attached must always be used.
2. PRODUCT INTRODUCTION
2.1 Items Included in the Package
After receiving the fixture, please carefully unpack the product and make sure the following parts are all included inside the package and are all in good condition.
The fixture x 4 pcs
Charger box x 1 pcs
Charging bag x 1 pcs
Infrared remote controller x 1 pcs
Power cable x 1 pcs
This manual x 1 pcs
In case the package is damaged from shipping, inform the carrier right away while keeping the damaged box or flight case for inspection. Failure to report damage to the carrier immediately may cause invalidity to your claim. The dealer or manufacture will not take any responsibilities for the damage.
In case there are parts missing from the package with a good condition, please contact your dealer or the manufacturer immediately by email or in other written form.
2.2 Product Overview
The fixture is a battery powered led luminaire with wireless DMX receiver. It features 3 super bright
RGBWA+UV hex color led, and can create more vivid color changing effects, and wide range of color temperatures.
The fixture has a rechargeable lithium-ion battery that can support 4.0 hours working at led full-color mode.
3
User’s Manual
The luminaire can continue working 7 hours to run its built-in programs and around 10 hours to run single color.
Its battery is fully protected against overcharging to maximize battery life span.
The fixture uses a very stable wireless DMX receiver (W-DMX Sweden compatible). The fixture can also be controlled with infrared remote controller. The IR controller can help users to achieve all working functions.
This highly compact luminaire has very small dimensions that can be used not only as an uplight but also as truss warmer. Its tilt can manually move 25 degrees when needed. It is absolutely an ideal tool for mobile
DJ/Bands, wedding, exhibitions, ball room and hotel banquet halls etc.
2.2.1 Fixture Elements and Connectors
1. OLED control panel
4. Bracket
7. Microphone
2. Wireless DMX antenna
5. Turning Knob
8. Power switch
3. DC charge input
6. Rubber foot
2.2.2 Fixture Control Panel
There are 4 touch buttons on the OLED control panel: < MENU >, < ENTER >, < UP > and < DOWN >.
4
User’s Manual
1. Menu To select the programming functions
2. Enter Enter the current menu or confirm the current function value
3. Up Scroll “UP” through the menu list to increase the value of the current function
4. Down Scroll “DOWN” through the menu list to decrease value of the current function
5. IR Infrared control sensor
6. Wireless DMX indictor
2.2.3 Fixture Dimensions
2.3 Fixture Temperature
The fixture has temperature protection function. You can easily check fixture temperature via the
OLED display information menu.
When fixture temperature is higher than 65 degrees, light output will decrease to 80%. When fixture temperature is higher than 65 degrees, light output will decrease to 60%. When fixture temperature is higher than 75 degrees, leds will go off automatically until temperature comes down to 55 degrees.
5
User’s Manual
2.4 Storing the Fixture
Make sure to fully charge all fixtures before storing. Partially charged batteries will lose capacity. Fully recharge every 6 months if not used.
Always remove battery fuse if fixture will be stored for long time (more than 1 month).
2.5 Mounting
The fixture can be mounted in several orientations.
2.5.1 The fixture has a highly compact housing, and can be fit inside 300x300mm truss as truss
warmer.
2.5.2 The fixture has 4 rubbber feet, and can sit on even and solid floor and work as an uplighter.
Make sure that the fixture is always placed on even and strong enough surface, and keep it
0.5m away from projection objects.
2.5.3 The fixture has multifunctional bracket. The fixture can be put on floor with various angles. It
can also be installed on crossbar and truss.
6
User’s Manual
When install the fixture to crossbar and truss, always use an extra safety cord (not supplied
with the fixture). Users also need to make sure the crossbar is stable or not moving, and can
support a weight of 16 kg (fixture net weight 1.6kg).
For the rest of safety installation, please always respect your local regulations.
2.6 Specifications
Electrical
Power input
100-240VAC 50/60Hz
Power consumption 35W
Power input/output connector DC input 12.8V 1.4A
Battery
Battery type Rechargeable lithium-ion battery
Charge time About 5.0 hours
Battery life 5 hours at full color from one full charge
5.5 - 6.0 hours full color at economy mode from one charge
8 hours at running preset programs
12 hours at running single color
Light sources
Led 3x10W, RGBWA+UV 6-in-1
Beam angle 25 o
Field angle 45 o
Led average life span 50,000 hours
Control
Control mode
DMX512, Master/Slave, Stand Alone; Wireless DMX, IR Remote
Control
DMX channel 6/8/12 channel selectable
Control panel OLED display with touch buttons
Physical & Construction
Housing Rigid metal
Housing color Black
Fixture dimensions 179 x 145 x 67.5mm
Net weight 1.6 kg
Working temperature -10 o
C - 45 o
C
Charging temperature 0 o
C - 45 o
C
IP rating IP20
Cooling Natural cooling, silent operation
7
User’s Manual
3. BATTERY CHARGING
The fixture has a rechargeable lithium battery and auto-ranging charger built in. Always store fixtures with full battery. Depleted batteries must be recharged immediately; otherwise fixture performance will suffer.
Battery runtime will decreased time by time. Battery runtime may be slightly shorter than predicted due to different working enviroments.
The fixture has a DC charging input. A normall charging time is about 4-5 hours.
Battery capacity can be easily seen on the OLED display.
It is recommended to charge the fixture at an ambient temperature between 0°C and 35°C.
If fixture is charged but not in operation, please always keep the power switch “Off”.
Note: The battery must be replaced with an original one from the manufacuturer only.
4. PRODUCT SETUP
Th is fixture has a built-in rechargeable lithium battery. After it is fully charged, switch on the fixture, it will start to run and can be controlled with wireless DMX desk or IR controller.
After operation, please switch off the fixture with its power switch.
4.1 OLED Display Protection
OLED display can be set to turn off in 10-60 second or always “On”.
Follow below steps:
- Continue pressing “Menu” till “Screensave” appears.
- Press “Enter” you will see , you can scroll up/down to set up how many
seconds the OLED display turns off, or always “On”
- Press “Enter” to save your setting.
8
4.2 Menu Navigation
User’s Manual
4.3 DMX Addressing
Each fixture must be given a DMX address so that the correct fixture responds to the correct control signals.
This DMX address is the channel number from which the fixture starts to “listen” to the digital control information being sent out from the controller.
This fixture has 3 DMX channel modes, 6, 8 and 12 DMX channels. To set up fixture DMX address, first select
DMX channel mode. The highest DMX address for this fixture is 512. To set up fixture DMX starting address, follow the steps below:
Switch on the fixture, press Menu till “ Channel” appears;
Press “Up” or “Down” button to select 6CH or 8CH or 12CH;
Press “Enter” to confirm your select.
Press “Menu” repeatedly to come back to “Address 001”;
Set up DMX address by scrolling “Up”/” Down” button.
Press “Enter” to save your setting.
-
9
User’s Manual
4.4 Wireless DMX Setup
This fixture can be controlled via wireless DMX system. Users need to pair the fixture to wireless DMX transmitter first.
There is one wireless DMX indicator near the OLED display. This indicator shows status of wireless DMX connection.
Indicator Status
Blue light on
Description
Fixture receiving wireless DMX signal from transmitter.
Blue light slow flashing
Blue light fast flashing
Fixture already connected to transmitter, but no signal coming from transmitter.
Fixture no connection to transmitter; fixture keeps. Wireless DMX memory from last pair.
Fixture no connection to transmitter, and no any wireless DMX memory. Bluelight off
4.4.1 Pairing n After fixture is switched on, and if there is no new transmitter, fixture will connect to the
old transmitter automatically, no need to re-pair it. n To clear wireless DMX memory, go to “menu” scroll up till you see “Wireless Reset”, press
Up/Down to select “Yes” and press “Enter” to reset wireless DMX. Then the blue light will turn off
in about 5 seconds. n To pair fixture and transmitter, after fixture wireless DMX is reset (make sure wireless DMX
indicator is Off), then press the pair button on the transmitter, fixture indicator will start to
fast flashing and then stay on, pair succeeds.
In optimal conditions, the master unit can operate up to 350m (visible distance) away from the slave units.
Please keep obstacles free between fixtures.
Once units have been linked to a specific transmitter, it will remain linked to that unit units it is linked to another one by clearing the intial wireless DMX signal.
To clear wireless DMX signal, set up your fixture as Slave first. Press "Enter", slave unit will start to erase all wireless DMX signal. Wireless DMX indicator will turn off in 5 seconds.
4.4.2 Wireless DMX Reset
To reset the fixture wirelss DMX signal , continue pressing “Menu” till “Wireless” a ppears. Press
Up/Down to select “Yes” or “No”, then press Enter to save your setup.
10
User’s Manual
5. OPERATION
5.1 DMX Control Mode
This function will allow users to control individual fixture with a standard DMX 512 console. Below is fixture
DMX Channel Chart.
Channel Mode Channel Function DMX Value Description
6 Ch
1
2
3
4
Red
Green
Blue
White
0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
8 CH
3
4
5
6
5
6
1
2
Amber
UV
Red
Green
Blue
White
Amber
UV
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
7 Dimming
12 CH
8
5
6
7
1
2
3
4
8
9
Strobe
Red
Green
Blue
White
Amber
UV
Dimming
Strobe white balance
0-255
0-15
16-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-10
11-255
0-10
11-30
31-50
51-70
111-130
131-150
151-170
171-200
201-205
0-100%
No function
Strobe from slow to fast
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
No function
Strobe from slow to fast
No function
R:100% G:0-100% B: 0
R: 100%-0 G100% B: 0
R:0 G:100% B: 0-100%
R: 0 G: 100%-0 B: 100%
R: 0-100% G:0 B: 100%
R: 100% G: 0 B: 100%-0
R: 100% G: 0-100% B: 0-100%
R: 100%-0 G:100%-0 B: 100%
R: 100% G: 100% B:100%
White 1
11
User’s Manual
12 CH
9
10
11
12
206-210
211-215
216-220
221-225
Colors macro
226-230
&
231-235 white balance
236-240
241-245
246-250
251-255
Auto run
0-10
11-40
41-70
71-100
101-130
Auto speed
Sound
131-160
161-190
191-220
221-255
0-255
0-10
11-255
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
No function
RGB color mixing
CMY color mixing
RGBA color mixing
RGBACMY color mixing
RGB color changing
CMY color changing
RGBA color changing
RGBACMY color changing
From slow to fast
No functioin
Sound mode
5.2 Auto Run Mode
The fixture has preset color mixing and fading programs that can be activated from the OLED control panel for auto running. To access this, follow below steps:
- Press button “Menu” until “ Program” appears.
- Press “Up” or “Down” to scroll up/down to select “Auto” and “Color”;
- Press “Enter” to confirm your run mode;
- Scroll “Up” or “Down” to select Auto programs (from 1 -5) or “Color” (from 1-30).
5.3 Sound Mode
The fixture can operate at sound mode to activate built-in programs with music.
Continue pressing “Menu” till “Program” appears. Press “Up” or “Down” to scroll up/down to select “Sound”.
Press “Enter” to save the setting.
12
User’s Manual
Press “Up” or “Down” to adjust sound sensitivity from high to low (from 1 to 9).
5.4 Customized Colors
Users are allowed to program their own color effects and save to your fixture. Follow the steps below:
- Press button “Menu” until “Color Custom 1” appears.
- Press “Enter”, you will see R (Red) is flashing, this means you now can program red color, press again
“Enter” and scroll “Up” or “Down” to adjust red intensity, press “Enter” again to save your setup.
- To select other colors “Up” or “Down” and press “Enter” to confirm the color you selected.
- Then scroll “Up” or “Down” to adjust the color intensity, and press “Enter” to save it
5.5 IR Remote Control
This operation mode allows users to control the fixture with an infrared remote controller. The remote controller can help you to achieve almost all functions.
To activate IR remote control, press “Menu” until “ IR” appears, press “Up” or “Down” button and select “ On”. Press “Enter” to save the setting.
To control the fixture with this IR remote controller, make sure to point the controller directly to the IR receiving sensors on the product. Make sure there are no objects between the controller and the fixture.
1 - Set the fixture into blackout (LED on/off).
2 - Adjust auto, strobe & fade speed, sound sensitivity, DMX
address, DMX channel, brightness etc.
3 - Run auto mode, use “Speed” button followed by the buttons to adjust auto speeds.
13
User’s Manual
4 – Run sound program, use
5 – Run strobe program, use bottons to adjust sound sensitivity. buttons to adjust strobe speed.
6 – Set auto/fade speed, Press this button followed by
7 – Set the fixture into master or slave mode.
8 – Run fade mode. Use “Speed” button followd by buttons to adjust program speed. buttons to adjust fade speed.
9 - Set DMX address. Pressthis button followed by
button again followed by to set up DMX address. Press this
to select DMX channel.
10 – Set the fixture in full brightness. Press this button followed by
brightness.
buttons to adjust
11 – Set the fixture in ECO mode.Press this button followed by buttons to turn ECO mode on/off.
12 – Set static color. This fixture has RGBA leds, so “White” and “UV” buttons are invalid.
6. MAINTENANCE
6.1 General Maintenance
The operator has to make sure that the safety-related and machine-technical installations are to be inspected by an expert once a year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be inspected by a skilled person once a year.
The following points have to be considered during the inspection:
- Make sure connections are clean and totally dry before linking equipments or supplying electric
power.
- All screws used for installing the fixture or parts of the fixture have to be tightly connected and must not be corroded.
The fixture has optical lenses; users should clean the lenses periodically to optimize light output. The cleaning frequency depends on the environment in which the curtain system is installed. Damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the lenses. Even in a clean type of surroundings, it is suggested to clean the lens and housing at least once a month. It is suggested to use a soft cloth using normal glass cleaning fluid.
14
User’s Manual
The following points have to be considered during the maintenance:
- Switch off the fixture before cleaning.
- Clean the lens with a mild solution of glass cleaner or isopropyl alcohol, and a soft, lint free cotton
cloth or a lens cleaning tissue.
- Gently polish the external glass surfaces until they are free of haze and lint.
6.2 Fuse Replacement
The fixture has an internal replaceable fuse built in the base.
In case fuse is blown, you need to replace it. Unplug the fixture from power, remove the 4 screw from the housing to find the fuse holder. Open the fuse holder by turning it anticlockwise; remove the blown fuse from the holder and replace it with the exact same type and rating one. Close the fuse holder by turning it clockwise to tighten it. Screw back the base to the housing.
Always replace a blown fuse with another of the same type and rating.
15
User’s Manual
7.
WARRANTY
The manufatuere, hereby warrants, to the original purchaser, our products to be free of manufacturing defects in material and workmanship for a period of one year (365 days) from the date of purchase. It is the owner's responsibility to establish the data and place of purchase by acceptable evidence, at the time service is sought. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner that the manufatuere concludes, after inspecting, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the manufatuere unless prior written authorization was issued to purchaser by the manufatuere. If the product is damaged because not properly maintained as set forth in the instruction manual. No warranty, whether expressed or implied, is given or made with respect to any accessory supplier with products described above. The consumer's and or
Dealer's sole remedy shall be such repair or replacement as is expressly provided.; and under no circumstances shall the manufatuere be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to the manufatuere. Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. The manufatuere reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
16
User’s Manual
MEMO :
17
User’s Manual
No content in this page
18
User’s Manual
Battery Powered
Wireless DMX
Luminaire
USER’S MANUAL
FOS Technologies Ltd.
Dealer info:
Copyright reserved
Manual version: Ver 1.0
Date: 20180512
19
advertisement
Key Features
- Rechargeable lithium-ion battery with 4.0 hours of working time at full-color mode
- 3 super bright RGBWA+UV hex color LEDs for vivid color-changing effects and a wide range of color temperatures
- Infrared remote controller for easy control of all working functions
- Highly compact design for use as an uplight or truss warmer
- Manual tilt adjustment of 25 degrees