advertisement
▼
Scroll to page 2
of
8
Model # 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed AFGSP = Glazed Spice finish AFCAF = Caffè finish Assembly Instructions IMPORTANT NOTES: For normal household use only. Not recommended to use this unit in a commercial setting. Unload items before you move this unit. Do not overload the drawers. Before you load or move this unit, tighten all screws and supports. Before you begin your project, completely read the Assembly Instructions. Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that range from 40°F to 90°F (not on a cold and possibly damp cement floor). Periodically inspect your furniture for any loose glue joints, screws or any other problem that might affect the stability of your furniture. Tighten or repair as needed. This assembly requires two people. WARNING Congratulations! This fine piece of furniture will make a gorgeous addition to your home. For the best results, read the Assembly Instructions before you begin your project. Notice to California Customers California Prop 65 requires consumer goods to be labeled if any one of 850+ different chemicals or substances, including wood dust, is present even in trace amounts. Drilling, sawing, sanding or machining wood products generates wood dust, a substance known to the State of California to cause cancer. Warning: This product contains a chemical or substance known to the State of California to cause cancer, birth defects or other reproductive harm. California Health and Safety Code Section 25249.6 DESIGN SUBJECT TO CHANGE WITHOUT NOTICE. CALL US FIRST! Do not return this item to the store. Service Policy: We will replace any part that is defective, missing or damaged during assembly. For a replacement part, contact Whittier Wood Products customer service department by phone, fax, mail or email. To Order: Provide the finish and furniture model number (upper portion of this page), the part letter, production code, quantity needed, reason for replacement and your full name, address and telephone number. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You may leave a message 24 hours a day, seven days a week. Parts ship from our Eugene, Oregon factory within one or two business days from the time we receive your request. Please allow five to ten business days for delivery 800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: 541-687-2060 www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A. Production Code: P.O. Box 2827 Eugene, OR 97402 USA VN 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Parts List Please identify the parts and check that quantities received match those on this list. If you need to replace a part, refer to the following letter and part name. 1455AFGSPa; 1455AFCAFa Headboard/Footboard Kit (x1) Part Description Quantity A Headboard Assembly 1 B Footboard Assembly 1 D 5/16" x 2-1/4" Hex Bolt 8 E 5/16" Flat Washer 8 F 1/4" x 80mm Hex Bolt 2 G 1/4" x 1-3/4" Hex Bolt 12 H 1/4" Flat Washer 12 I Barrel Nut 2 J 3/8" x 1" Wood Dowel 2 K Angle Bracket (attached) L #6 x 3/4" Flat Head Screw S U Hex Wrench Hanger Bolt (attached) 1 6 V ZA 5/16" x 3/4" Insert Nut (inserted) #6 x 1-1/4" Black Pan Head Screw (inserted) 14 92 ZF Adjustable Glide with Hex Nut (installed) 6 ZG Assembled Foot 6 1452AFGSPb_1452AFCAFb — Page 2 — 12/13 2 12 (6 inserted) 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Parts List 1453AFGSPb; 1453AFCAFb Pedestal Kit (x2) Part Description Quantity N Pedestal Kit 1 O Drawer Box (inserted) 3 P Drawer Face (attached) 3 R Drawer Slides (pre-installed sets) 3 T T-Nut (inserted) 9 X ZA #7 x 1-1/2" Black Pan Head Screw (inserted) #6 x 1-1/4" Black Pan Head Screw (inserted) 79 12 ZB #8 x 20mm Pan Head Screw (inserted) 12 ZC Small Angle Bracket (attached) 4 ZD #6 x 1/2" Philtruss Screw (inserted) 42 ZE #6 x 3/4" Philtruss Screw (inserted) 18 ZI #8 x 7/8" Black Lo-Profile Screw (inserted) 18 1452AFGSPb_1452AFCAFb — Page 3 — 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Assembly Instructions This assembly requires two people. Tools Required: Hex Wrench (provided), Phillips Screwdriver, Slotted Screwdriver, 1/2" Wrench, 7/16" Wrench, Tape Measure, Rubber Mallet or Padded Hammer, Wood Glue 1. Remove the Drawers (O) from the Pedestal Kits (N). To remove the drawers, pull up on the left Drawer Release Lever while pushing down on the right Drawer Release Lever. See Figures 1 and 1a. Note where each drawer came from to ensure correct re-installation. Positions are marked on the drawer bottoms. O Fig. 1a Fig. 1 Drawer Release Lever 2. To protect your flooring and the surface of the unit, place the Pedestal Kits (N) face-down on top of opened and unfolded 1453 cartons as shown in Figure 2. (When you join the pedestals, carpet fibers can get caught in between the middle supports.) Place twelve 1/4" Washers (H) over twelve 1/4" x 1-1/4" Hex Bolts (G) and thread each through a pre-drilled hole and into a T-Nut in the middle support found on each pedestal. Finger tighten each bolt, making sure the pedestals line up with each other. Afterwards, use a 7/16" wrench to securely tighten each bolt. See Figure 2. G T Unfolded 1453 cartons T G x 12 H x 12 T H N T T Fig. 2 1452AFGSPb_1452AFCAFb — Page 4 — 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Assembly Instructions This assembly requires two people. 3. Rotate the Adjustable Glides with Hex Nut (ZF) so that the Assembled Feet (ZG) are 4-1/2" tall as shown in Figure 3a. Attach the six Assembled Feet (ZG) as shown in Figure 3. ZF ZG 4-1/2" x6 ZG Fig. 3a Fig. 3 4. This step requires two people to move the bed to its upright horizontal position. Rotate the bed so the deck boards face up. DO NOT PLACE UNDUE PRESSURE ON THE ASSEMBLED FEET. See Figure 4. Fig. 4 1452AFGSPb_1452AFCAFb — Page 5 — 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Assembly Instructions This assembly requires two people. 5. Spread a thin film of glue in the dowel holes at one end of the top cap of the bed. Insert two dowels (J) and gently tap with a rubber mallet. Quickly wipe away any excess glue. See Figures 5 and 5a. J x2 J Top Cap J J Fig. 5a Fig. 5 6. Position the Footboard (B) against the end of the pedestal assembly and insert the dowels (J) into the oval holes in the top cap of the footboard. Place four 5/16" Washers (E) over four 5/16" x 2-1/4" Hex Bolts (D) and thread the washer/bolts through the predrilled holes in the Pedestal Assembly and into the Footboard. Tighten the bolts with a 1/2" wrench. See Figures 6, 6a and 6b. J Fig. 6a D x4 E x4 J Top Cap B Fig. 6 D E J Fig. 6a DE 1452AFGSPb_1452AFCAFb — Page 6 — 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Assembly Instructions This assembly requires two people. 7. Position the Headboard (A) against the end of the pedestal assembly. Place four 5/16" Washers (E) over four 5/16" x 2-1/4" Hex Bolts (D) and thread the washer/bolts through the predrilled holes in the Pedestal Assembly and into the Headboard. Tighten the bolts with a 1/2" wrench. See Figure 7. D x4 E x4 Fig. 7 E 8. D Secure the pre-attached Angle Brackets (K) on the Headboard to the Pedestal Assembly with six #6 x 3/4" Flat Head Screws (L). See Figures 8 and 8a. Insert one Barrel Nut (I) into the predrilled holes on the bottom of the left pedestal rail. Using a slotted screwdriver, line up the hole in the Barrel Nut to the hole in the Headboard. Insert one 1/4" x 80mm Hex Bolt (F) into the predrilled hole in the Headboard and tighten with the provided Hex Wrench (S). Repeat for the right side. See Figures 8 and 8b. F I Fig. 8b F x2 I x2 L x6 F Fig. 8 L K 1452AFGSPb_1452AFCAFb — Page 7 — 12/13 1452AFGSPb; 1452AFCAFb Pacific King Storage Bed Assembly Instructions This assembly requires two people. 9. Place your bed into its final position; verify that all 6 Assembled Feet (ZG) are touching the floor and carrying weight, if needed, use a 1/2" wrench to adjust the Adjustable Glides (ZF) on the bottoms of the Assembled Feet (ZG). See Figure 9. Carefully align the drawer slides and gently insert the six drawers into their correct positions. Sleep well and enjoy! Fig. 9 ZG ZF 1452AFGSPb_1452AFCAFb — Page 8 — 12/13
advertisement