Asus PG191 User guide

PG191 LCD Monitor

User Guide

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS

OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR

ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND

SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY

OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,

INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Table of contents

Notices ................................................................................................. v

Safety information .............................................................................. vi

Care and cleaning ............................................................................... vii

Package contents ............................................................................... ix

Chapter 1: Product introduction

1.1

Welcome! .............................................................................. 1-2

1.2

Features ............................................................................... 1-2

1.3

Monitor introduction ............................................................. 1-3

Chapter 2: Setup

2.1

Connecting the cables .......................................................... 2-2

2.2

Turning on the monitor ........................................................ 2-3

2.3

Adjusting the tilt .................................................................. 2-3

Chapter 3: General Instruction

3.1

OSD (On-Screen Display) menu ............................................ 3-2

3.1.1

How to reconfigure ................................................. 3-2

3.1.2

OSD function introduction ...................................... 3-2

3.2

Using the built-in webcam .................................................... 3-4

3.2.1

Hardware ................................................................ 3-4

3.2.2

Software ................................................................. 3-4

3.3

LifeFrame software .............................................................. 3-5

3.3.1

Introduction and installation instructions ............... 3-5

3.3.2

Main screen ............................................................. 3-6

3.3.3

Preview mode ......................................................... 3-7

3.3.4

Status bar ............................................................... 3-7

3.3.5

Operating area ........................................................ 3-8

3.3.6

Enhance .................................................................. 3-9

3.3.7

Effects .................................................................. 3-10

3.3.8

Setup - basic setup .............................................. 3-11

3.3.9

Setup - capture format ........................................ 3-12

3.3.10 Setup - capture mode .......................................... 3-13

Chapter 4: Appendix

Appendix I SRS TruSurround XT™ ................................................ 4-2

Appendix II Troubleshooting (FAQ) .............................................. 4-3

Appendix III PG191 specification summary ................................... 4-4

Appendix IV Supported operating modes ...................................... 4-6

Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Safety information

• Before setting up the monitor, carefully read all the documentation that came with the package.

• To prevent fire or shock hazard, never expose the monitor to rain or moisture.

• Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.

• Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided.

• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

• Use the appropriate power plug which complies with your local power standard.

• Do not overload power strips and extention cords. Overloading can result in fire or electric shock.

• Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.

• Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.

• Never push objects or spill liquid of any kind into the slots on the monitor cabinet.

• To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC.

• If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.

Care and cleaning

• Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.

• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner.

• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the LCD. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.

• The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.

• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

• When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.

• When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself!

complete a task.

when trying to complete a task.

task.

Refer to the following sources for additional information and for product and software updates.

1 .

A S U S w e b s i t e s

The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com

2 .

O p t i o n a l d o c u m e n t a t i o n

Your product package may include optional documentation, such as warranty card, that may have been added by your dealer. These documents are not part of the standard package.

Package contents

Check your PG191 LCD package for the following items:

LCD monitor

Quick Start Guide

Support CD

1 x Power cord

1 x VGA-Audio-Microphone-USB 4-in-1 cable

1 x DVI cable

If any of the above items is damaged or missing, contact your retailer immediately.

xxxxx

Chapter 1

the ASUS PG191 LCD monitor. The chapter lists the monitor features including introduction on the front/rear panels as well as the side view.

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

1.1

Welcome!

Thank you for purchasing the ASUS ® PG191 LCD monitor!

The LCD monitor features high-quality audio technology, including a detachable 15W ASUS Power Bass System and the most advanced SRS

TruSurround XT™ sound effect which help provide vivid melody, enhancing your audio enjoyment while you watch movies, play games, or listen to music! The built-in 1.3 megapixel webcam on top of the LCD panel has both video recording and snapshot functions, allowing you to capture images, create videos, or hold a video conference! Besides, a host of user-friendly funcitons such as the rotating swivel, adjustable tilt, and smart touch sensor buttons facilitate the usage of the monitor, upgrading your work efficiency.

With these features, you enjoy the convenience and delightful audio-visual experience that the PG191 brings you!

1.2

Features

19" TFT LCD Monitor

True resolution: 1280 X 1024 (SXGA)

2ms (gray-to-gray) quick response time

5W x2 stereo speakers

15W Power Bass System (detachable)

SRS TruSurround XT™ sound effect (See Appendix I)

3 USB 2.0 ports

Built-in 1.3 megapixel webcam

SPLENDID™ Video Intelligence Technology

5 SPLENDID™ video preset modes switched by hotkey

3 skin-tone selections

5 sound preset modes switched by hotkey

Touch sensor controls

Both VGA and DVI-D Inputs

Headphone output & microphone input

Microsoft ® Windows ® 2000/XP compliance

VESA Display Data Channel DDC2B compliance

VESA wall mount compliance (100 x 100 mm)

EPA ENERGY STAR ® and ergonomic design

RoHS compliance

1.3

Monitor introduction

The touch sensors are sensitive. Slightly touch the item you want to enable. Do not press the front panel too hard to prevent damage to the panel and the sensors.

1.

• Use this hotkey to switch to any of the five sound preset modes

(Standard Mode, Fighting Game Mode, Strategic Game Mode,

Theater Mode, Music Mode).

2.

S e n s o r :

• Touch this sensor to activate the OSD (On-Screen Display) main menu.

• Touch this sensor to enter/select the item (function) highlighted

while the OSD menu is activated.

3.

• Touch this sensor to increase the value of the function selected

or move to the next function.

• This is also a hotkey for Brightness adjustment.

4.

S e n s o r :

• Touch this sensor to decrease the value of the function selected

or move to the previous function.

• This is also a hotkey for Volume adjustment.

• Use this hotkey to switch to any of the five video preset modes

(Standard Mode, Theater Mode, Game Mode, Night View Mode,

Scenery Mode) with SPLENDID™ Video Intelligence Technology.

• Exit the OSD menu or go back to the previous menu as the OSD

menu is active.

• Automatically adjust the image to its optimized position, clock,

and phase by touching the sensor for 2-3 seconds.

6.

P o w e r s e n s o r / L E D i n d i c a t o r

• Touch this sensor to turn the monitor on/off

Blue

Amber

OFF

Power ON

Standby mode

Power OFF

1 S R S O n / O f f b u t t o n . sound effect.

2.

U S B 2 . 0 p o r t s . available for connecting USB 2.0 devices.

3.

M i c r o p h o n e p o r t .

(3.5mm).

4.

H e a d p h o n e p o r t . mini-plug (3.5 mm).

The headphone and the microphone are purchased separately.

3 4 5 6 7

1. AC-in port

2. DVI port

3. VGA port

4. Audio-input port

5. Woofer port

6. Microphone-output port

7. USB port (Upstream)

Chapter 2

This chapter provides setup instruction on how to correctly connect cables and properly adjust the monitor to a comfortable viewing angle via tilt and swivel functions.

2.1

Connecting the cables

Connect the cables as shown:

2 3

1. Power cord

2. DVI cable

3. VGA cable

4. Audio cable (gray)

5. Woofer cable

6. Microphone cable (red)

7. USB cable

6 7

• To connect the USB cable:

USB cable to the monitor’s USB port (as the above drawing shows), the other end to the computer’s.

• To connect the microphone/audio cables: end (red/gray) of the microphone/audio cables to the monitor’s microphone-out/audio-in ports, the other end (red/green) to the computer’s microphone-in/audio-out ports.

• To connect the VGA/DVI cables: a. Plug the VGA/DVI connectors to the monitor’s VGA/DVI

ports.

b. Connect the other end of the VGA/DVI cables to your

computer’s VGA/DVI ports.

c. Tighten the two screws to secure the VGA/DVI connectors.

• T o c o n n e c t t h e p o w e r c o r d : power cord securely to the monitor’s AC input port, the other end to a power outlet.

• T o c o n n e c t t h e w o o f e r c a b l e : the monitor’s woofer port.

The supplied VGA-audio-microphone-USB 4-in-1 cable combines the

VGA cable, audio cable, microphone cable, and USB cable.

2.2

Turning the monitor on

Gently touch the power sensor . See page 1-3 for the location of the power sensor. The power indicator lights up in blue to show that the monitor is ON.

2.3

Adjusting the monitor

This monitor can be adjusted within the angles as shown:

We recommend that you adjust the viewing angle of the monitor based on the height of your desk and chair to prevent the light from reflecting to your eyes.

1.

Grasp the top of the monitor and adjust the tilt within -5º to 25º.

-5º~25º

2.

The swivel base allows you to turn the monitor left/right up to 120º.

120º

Chapter 3

This chapter introduces the general instruction, including how to use the

OSD (On-Screen Display) menu and activate the LifeFrame utility.

3.1

OSD (On-Screen Display) menu

3.1.1

How to reconfigure

1.

Touch the sensor to activate the OSD menu.

2.

Touch and to navigate through the functions. Highlight and activate the desired function by touching the sensor. If the function selected has a sub-menu, touch and again to navigate through the sub-menu functions. Highlight and activate the desired sub-menu function by touching the sensor.

3.

Touch and to change the settings of the selected function.

4.

To exit the OSD menu, touch the sensor. Repeat step 2 and step 3 to adjust any other function.

3.1.2

OSD function introduction

See the table on the next page for details.

• Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal disturbances.

• Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional.

O S D m e n u t a b l e :

M a i n S u b - m e n u 1 S u b - m e n u 2 D e s c r i p t i o n

Scenery Mode

Standard Mode

Theater Mode

Game Mode

Night View Mode

Brightness

Contrast

Sharpness

Saturation

Position

(For VGA only)

Focus

(For VGA only)

Color Temp.

Skin Tone

Preset Mode

H-Position

V-Position

Phase

Clock

Cool

Normal

Warm sRGB

User Mode

Reddish

Natural

Yellowish

Standard Mode

Fighting Game Mode

Strategic Game Mode

Theater Mode

Music Mode

On/Off SRS TSXT

True Bass

Balance

Equalizer

Melody On/Off

Power key

Function key

VGA/DVI

Video preset mode for viewing scenery

Video preset mode for generic windows use

Video preset mode for watching movies

Video preset mode for playing games

Video preset mode for displaying night views

Adjusts brightness of the image

Adjusts contrast of the image

Adjusts sharpness of the image

Adjusts saturation of the image

Adjusts horizintal position of the image

Adjusts vertical position of the image

Reduces the horizontal-line noise of the image

Reduces the vertical-line noise of the image

The image appears bluer. (9300ºK)

Normal image color. (7500ºK)

The image appears redder. (6500ºK)

The image appears sRGB standard color for multimedia designers

Adjusts Red/Green/Blue levels of the image

Selects reddish skin stone

Selects natural skin stone

Selects yellowish skin stone

Sound preset mode for generic windows use

Sound preset mode for playing fighting games

Sound preset mode for playing strategic games

Sound preset mode for watching movies

Sound preset mode for listen to music

Turns on/off the SRS TSXT sound effect

Adjusts the TruBass bass level while SRS TSXT is on

Adjusts the balance between right and left channel sounds

Adjusts 5 bands (100Hz, 300Hz, 1KHz, 3KHz, 10KHz)

Turns on/off the melody function

Selects a power on/off melody

Selects a function key melody

Selects a preferred input source

OSD Setup

Language

Information

Reset

H-Position

V-Position

OSD Timeout

No/Yes

Adjusts horizontal position of the OSD

Adjusts vertical position of the OSD

Adjusts OSD timeout

Selects a preferred language

Shows the resolution,H/V frequency and input port of current inputtiming

Recalls default setting

3.2

Using the built-in webcam

This built-in webcam allows you to take photos and make videos; while talking to friends via Internet-based communication tools, you can use the webcam to show your vivid image.

3.2.1

Hardware

• The 1.3 megapixel webcam transmits images to your PC through the USB ports. Therefore, make sure that you have connected the USB plugs of the supplied 4-in-1 cable before you use the webcam.

• The webcam is adjustable upward and downward as shown.

-30º ~ 30º

Warning: Do not turn the webcam upward or downward over 30º; doing so might damage the webcam.

3.2.2

Software

1. Close all other applications first.

2. Insert the support CD into the optical drive and run the

The default webcam resolution is 640 x 480. If you want to change the default resolution to meet different kinds of application programs, go to named LifeCam to modify the settings based on your needs.

• The default webcam captured video format is VGA (640 x 480) mode in order to increase the transmission efficiency via all kinds of

Internet commmunication tools.

• Before using the webcam, you need to install the webcam driver into your PC.

• The webcam driver only supports Microsoft ® Windows 2000/XP operating system with Microsoft ® Direct X.

3.3

LifeFrame software

3.3.1

Introduction and installation instructions

To capture snapshots or video clips, ASUS PG191 provides an easy-to-use LifeFrame that can work with the built-in webcam, allowing users to create their own photos or video clips.

• LifeFrame only supports Microsoft ® Windows ® 2000/XP operating systems.

• Before starting to use this software, install LifeFrame into your PC.

• The LifeFrame software is bundled in the PG191 support CD.

1. A personal computer with Pentium ® III 800 MHz or higher processor

2. Microsoft ® Windows ® 2000/XP operating systems

3. Minimum 200 MB free hard disk space to run the program

4. 128 MB of RAM or above

5. A display card supporting 16-bit high color mode

1. Close all other applications.

2. Insert the support CD into the optical drive and run the

LifeFrame program.

3. Follow the on-screen instructions to complete the installation

Make sure that you connect the USB plug of the supplied 4-in-1 cable to the USB port at the back of the LCD monitor; otherwise, the built-in webcam and LifeFrame will not be activated.

3.3.2

Main screen

The main screen shows the following function areas:

1.

P r e v i e w w i n d o w

3.4.3 for details.

2.

S t a t u s b a r mode. See section 3.4.4 for details.

3.

O p e r a t i o n a r e a .

snapshot mode, continue capture, interval

capture, auto motion detective capture

4.

I m a g e d i s p l a y a r e a . thumbnails listed in descending order according to image creation time.

5.

A p p l i c a t i o n a r e a your saved images: mode switch, email, save, and delete. Refer to the next page for details.

modes.

to send as an attachment.

You can select multiple files to delete.

3.3.3

Preview mode

Click the thumbnail you wish to preview.

1.

Click the movie recorder icon on the lower right corner.

2.

Click the thumbnail to preview.

3.

Buttons will appear. Use these buttons to play the video.

pause play stop progress

3 . 3 . 4 Status bar

The status shows the following information.

HD space/file size

3.3.5

Operating area

- Enhance

- Effects

- Setup

1.

M u t e .

2.

V i d e o m o d e .

3.

R e c o r d .

4.

S n a p s h o t m o d e .

5.

C o n t i n u e c a p t u r e .

6.

I n t e r v a l c a p t u r e :

7.

A u t o m o t i o n d e t e c t i o n c a p t u r e .

“Stop” to end

• To add sound to your video clips, ensure that you connect a microphone to the monitor.

• The microphone is purchased separately.

3 . 3 . 6 Enhance

There are several options to enhance the quality of your captures.

3.3.7

Effects

Enrich your images with special effects.

3.3.8

Setup - basic setup

There are three pages: Basic Setup, Capture Format, and

Capture Mode.

kinds of picture rotating angles.

3.3.9

Setup - capture format

Many options for output size, image format/quality, and video format/quality.

176x144, 320x240, 352x288, 640x480, 1280x1024

You can adjust the capture mode with the following three items: recording time limited, auto capture sensitivity, and capture interval setting.

the maximum will be 120 minutes; default maximum time limit is 30 seconds. One single file size should not be bigger than 2 GB.

detect.

the default value is 5 seconds.

Chapter 4

This appendix provides the introduction of

SRS TruSurround XT™, troubleshooting

(FAQ), specification summary, and supported operating modes.

Appendix I.

SRS TurSurround XT™

SRS TruSurround XT is a novel audio technology which provides an enhanced listening experience. Utilizing proprietary algorithms from SRS

Labs, TruSurround is intended to regenerate a realistic audio environment, where users feel like being surrounded by sound.

TruSurround XT is a combination of four distinct and patented processing techniques from SRS Labs:

• disturbance derived from multichannel and improves the dialog clarity of movies, PC games, on-line chats, etc.

• multichannel formats, allowing you to enjoy virtual surrounding sound experience.

• techniques, the TruBass technology restores low-frequency tones by augmenting harmonics.

• the sound space in both the horizontal and vertical planes, trully providing a 3D stereo experience.

Appendix II.

Troubleshooting (FAQ)

Screen image is blurry or fuzzy

No sound or sound is low

P r o b l e m

Power LED is not ON

The Power LED lights amber and there is no screen image

Screen image is too light or dark

Screen image is not centered or sized properly

Screen image bounces or a wave pattern is present in the image

Screen image has color defects (white does not look white)

Webcam is not working

USB devices work abnormally

ASUS Power Bass

System is not working

P o s s i b l e S o l u t i o n

• Touch the sensor to check if the monitor is in the ON

mode.

• Check if the power cord is properly connected to the

monitor and the power outlet.

• Check if the monitor and the computer are in the ON mode.

• Make sure the signal cable is properly connected the

monitor and the computer.

• Inspect the signal cable and make sure none of the pins are

bent.

• Connect the computer with another available monitor to

check if the computer is properly working.

• Adjust the Contrast and Brightness settings via OSD.

• Touch the sensor for two seconds to automatically

adjust the image.

• Adjust the H-Position or V-Position settings via OSD.

• Make sure the signal cable is properly connected to the

monitor and the computer.

• Move electrical devices that may cause electrical

interference.

• Inspect the signal cable and make sure that none of the

pins are bent.

• Perform Reset via OSD.

• Adjust the R/G/B color settings or select the Color

Temperature via OSD.

• Touch the sensor for two to three seconds to

automatically adjust the image.

• Adjust the Phase and Clock settings via OSD.

• Ensure that the audio cable is properly connected to the

monitor and the computer

• Adjust the volume settings of both your monitor and

computer.

• Ensure that the computer sound card driver is properly

installed and activated.

• Ensure that you install the webcam driver which is in the

support CD.

• Make sure that you connect the USB plugs of the supplied

4-in-1 cable to both the LCD monitor and your computer.

• Make sure that you connect the USB plugs of the supplied

4-in-1 cable to both the LCD monitor and your computer.

• Check with your PC manufacturer whether your PC supports

USB2.0 or USB1.1.

• If your PC only supports USB1.1, the image transmission is

much slower.

• Make sure that the woofer cable is securely connected to the

monitor.

Appendix III. PG191 specification summary

TFT LCD

19.0”

SXGA + 1280 x 1024

0.294 mm

300cd/m 2

800:1

160º/160º

16.2M

2ms (GTG)

Yes

5 Modes (by hotkey)

3 Skin-tones

5 Modes (by hotkey)

Yes (by hotkey)

Cool/Normal/Warm/sRGB/User Mode

24-Pin DVI-D & 15-Pin D-Sub

3.5mm Mini-jack

3.5mm Mini-jack

3.5mm Mini-jack

Black + Silver

5W x 2 (Stereo) + 15W Power Bass System

Blue (ON)/ Amber (Standby)

+25º ~ -5º

+60º ~ -60º

(continued on the next page)

100 x 100 mm

Yes

AC: 100-240V~, 50Hz-60Hz

Power On: < 90W, Standby: < 2W,

10.5 Kg (approx.)

444.9 mm (W) x 463.4 mm (H) x 240.0 mm (D)

VGA-Audio-Microphone-USB 4-in-1 cable, DVI cable, Power cord, Support CD (LifeFrame bundled), Quick Start Guide

Energy Star ® , UL/cUL, CB, CE, FCC, CCC, BSMI,

Gost-R, C-Tick, VCCI, RoHS, MIC

***** Specifications are subject to change without notice.

Appendix IV.

Supported operating modes

DOS

VGA

SVGA

720 x 400 31.47KHz

640 x 480 31.47KHz

640 x 480 37.90KHz

640 x 480 37.50KHz

800 x 600

800 x 600

800 x 600

35.16KHz

37.90KHz

48.10KHz

70Hz 28.32MHz

60Hz

72Hz

75Hz

25.18MHz

31.50MHz

31.50MHz

56Hz

60Hz

72Hz

36.00MHz

40.00MHz

50.00MHz

XGA

SXGA

800 x 600

1024 x 768

1024 x 768

1024 x 768

1280 x 1024

1280 x 1024

46.90KHz

48.40KHz

56.50KHz

60.02KHz

64.00KHz

78.00KHz

75Hz

60Hz

70Hz

75Hz

60Hz

75Hz

49.50MHz

65.00MHz

75.00MHz

78.75MHz

108.00MHz

135.00MHz

VESA 1152 x 864 67.50KHz

75Hz 108.00MHz

* Modes not listed in the table may not be supported. For optimal resolution, we recommend that you choose a mode listed in the table above.