BenQ E1460 Camera User Guide
Annonce
Annonce
E1460_UM - EN.book Page 1 Thursday, September 23, 2010 6:43 PM
E1460 Series
Digital Camera
User Manual
Welcome
E1460_UM - EN.book Page 2 Thursday, September 23, 2010 6:43 PM
Copyright
Copyright 2010 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of this company to notify any person of such revision or changes.
All other logos, products, or company names mentioned in this manual may be the registered trademarks or copyrights of their respective companies, and are used for informational purposes only.
Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.
This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handing it over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For more information about recycling of this equipment, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.
CE Regulatory Notice
Hereby, BenQ Corp. declares under our responsibility that the product is in conformity with the requirements set out in the Council Directive on the Approximation of the Laws of the Member
States relating, Electromagnetic Compatibility Directives (2004/108/EC) and Low Voltage Directive
(2006/95/EC).
A “Declaration of Conformity” in accordance with the above Directives has been made and is available from BenQ Corp. upon request.
E1460_UM - EN.book Page 3 Thursday, September 23, 2010 6:43 PM
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
E1460_UM - EN.book Page 4 Thursday, September 23, 2010 6:43 PM
Safety warning and notice
Before operating the camera, please make sure that you read and fully understand the content in this section. If you ignore and violate all safety warning notices indicated in this section, the camera warranty may be void. Meanwhile, not only the camera but also you and all other people and things around you may be severely damaged, injured, or even placed in danger of death.
For your safety
• Keep the camera and its accessories out of the reach of babies, toddlers, and children. In particular, small parts such as memory cards and batteries could be easily dismantled and swallowed by them.
• Use only the original accessories to avoid possible risks to health and property, and thus meet all related legal regulations.
• Do not dismantle the camera under any circumstances.
• When using the flash, do not go too close to human eyes (particularly for babies, toddlers, and children) or animal eyes. Otherwise, when the flash fires, the light may cause damage to human eyes or irritate animals.
• Batteries could explode, for instance. All batteries can cause property damage, injury or burns if a conductive material such as jewelry, keys or beaded chains touch exposed terminals. The material may complete an electrical circuit and become quite hot. Exercise care in handling any batteries, particularly when placing it inside your pocket, purse, or other container with metal objects. Do not dispose of batteries in fire as they may explode.
• To prevent electric shock, do not attempt to disassemble or repair your camera by yourself.
• Some camera models accept non-rechargeable batteries. When using these batteries, do not charge them. Otherwise, dangers such as explosion and fire may occur.
Warranty
• Warranty is void if damage or system failure occurred due to outside factors such as collision, fire, flood, dirt, sewage, earthquake, and other force majeure events as well as incorrect usage of electricity or use of non-original accessories.
• It is the sole responsibility of the user if problems (such as data loss and system failure) occurred due to non-factory installed software, parts, and/or non-original accessories.
• Do not change the camera. Any changes to the camera invalidate the warranty.
Taking care of your camera
• Always keep the camera in the accompanying leather case or pouch for better protection against splashes, dust, and collision.
• The only way of replacing the battery and the memory card is to open the Battery / Memory cover.
• Dispose of unwanted batteries and cameras as permitted by the laws in your countries.
• Water may cause a fire or electric shock. Therefore, store your camera in a dry place.
• If your camera becomes wet, wipe it with a dry cloth as soon as possible.
• Salt or seawater may cause severe camera damage.
• Do not drop, knock, or shake the camera. A rude behavior of using the camera may damage the internal electronic circuit board, deform the lens shape, or make the lens unretractable.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the camera.
• Finger grease may be left on the camera lens and will result in unclear images or videos. To avoid this problem, be sure to clean the camera lens before taking pictures or recording videos. You should also clean the camera lens on a regular basis.
• If the lens is dirty, use a lens brush or soft cloth to clean the lens.
• Do not touch the lens with your fingers.
E1460_UM - EN.book Page 5 Thursday, September 23, 2010 6:43 PM
• If a foreign substance or water gets in your camera, please turn the power off immediately and disconnect the batteries. Next, remove the foreign substance or water and send it to the maintenance center.
• Whenever there is data in the internal memory or the external memory card, you should make a backup copy to a computer or disc. So, you can have a backup solution if data loss occurs.
• If the lens cannot retract into the camera, please replace the batteries first (usually this is because of drained batteries). Then the lens should retract automatically. If the lens still cannot retract, please contact your dealer.
• Under no circumstances should you push the lens back manually as this may damage the camera.
• All original accessories are designed only for use with this camera model you purchased. Do not use these accessories with other camera models or cameras of other brands to avoid unpredictable danger or damage.
• Before initial use of a memory card, always use the camera to format the card first.
• Remember to slide the write-protect tab (if available) to the unlock position. Otherwise, all data
(if any) on the memory card is protected and the card cannot be edited or formatted.
Operating environment
• Do not use or store your camera in the environments listed below:
• Direct sunlight
• Dusty places
• Next to an air conditioner, electric heater or other heat sources
• In a closed car that is in direct sunlight
• Unstable locations
• Do not use your camera outdoors when it is raining or snowing.
• Do not use your camera in or near water.
• The camera operating temperature is between 0 and 40 degrees Celsius. It is normal for the operating time to be shortened when the temperature is low.
• The capacity of your camera batteries will reduce each time it is charged/emptied.
• Storage at too high or low temperatures will also result in a gradual capacity loss. As a result, the operating time of your camera may be considerably reduced.
• It is normal for the camera to become warm during operation, because the camera casing can conduct heat.
E1460_UM - EN.book Page 6 Thursday, September 23, 2010 6:43 PM
Do not hold the camera by excessive force. Plus, be sure to protect the camera from strong impacts.
To avoid accidental falling, please attach the hand strap to the camera and always hold the camera by keeping the hand strap around your wrist.
If the battery suddenly depleted and caused the lens fail to retract, please carefully protect the lens to avoid collision and insert a battery with full power ASAP.
When the camera is not in use, always turn the power off and make sure the lens has retracted successfully before storing the camera in its case. If you do not intend to use the camera for a long time, please remove the battery from the camera and store the battery carefully.
Keep your camera away from sharp objects and avoid collision.
When the camera is not in use, please place it in a steady place. Plus, always keep your camera away from pressure or any other similar environment
(for example, in a pant pocket) to avoid possible damage.
E1460_UM - EN.book Page 1 Thursday, September 23, 2010 6:43 PM
Table of Contents
Touring the camera ......................................................................... 1
Preparing the camera for use .......................................................... 3
Operating the camera ...................................................................... 8
Capture mode .................................................................................. 9
More capture options in the Function menu ................................................ 10
Auto Exposure Bracketing (AEB) .................................................................. 22
Setting sharpness, saturation and contrast .................................................... 23
E1460_UM - EN.book Page 2 Thursday, September 23, 2010 6:43 PM
Other settings ................................................................................. 28
Playback mode ............................................................................... 31
Working with computer and AV system ...................................... 39
Connecting the camera to a computer .......................................................... 39
Connecting the camera to an AV system ....................................................... 39
Troubleshooting and service information ................................... 41
Specifications ................................................................................. 43
E1460_UM - EN.book Page 1 Thursday, September 23, 2010 6:43 PM
Touring the camera 1
Touring the camera
Checking the package contents
Carefully unpack your kit box and ensure that you have the following items.
1. User Manual or
Quick Guide
2. Digital camera
3. USB cable
4. Battery
5. Hand strap
6. Software & User
Manual CD
7. Leather case
8. AC power adapter
• All pictures, screen captures, and icons used in this manual are for illustration only. Actual and available products, accessories, as well as their appearance may vary depending on sales region.
• If any items are missing or damaged, contact your dealer.
• Save the packaging for future shipment or storage.
E1460_UM - EN.book Page 2 Thursday, September 23, 2010 6:43 PM
2 Touring the camera
Camera
Front view and bottom view
1.
T (Tele) - Zoom-in or turn on the Shooting mode description
2. Shutter button
3.
W (Wide) - Zoom-out, turn off the Shooting mode description, or enter the thumbnail view (Playback mode)
4. Power button
5. S.S.F. (Super Shake-Free) button
6. Flash
7. AF Assist Lamp / Self-timer LED indicator
8. Lens
9. Microphone
10. Speaker
11. Tripod mount
12. USB / AV port
13. Battery / Memory card cover
Rear view
1. LCD display
2. Status LED
3. Mode switch - Toggle among Capture
(photo), Capture (movie), and Playback modes
4. Strap eyelet
5. Multifunctional buttons (including a
4-way control and a button)
6. Function / Delete button -
Activate the function menu (Capture mode) or delete photos (Playback mode)
7. MENU button previous menu
or return to the
E1460_UM - EN.book Page 3 Thursday, September 23, 2010 6:43 PM
Preparing the camera for use 3
Indicator
Status LED
State
No light
Solid green
Blinking green
Description
The digital camera is off.
• The digital camera is ready to capture images.
• The digital camera is powering on, or is in the power-saving mode.
• The digital camera cannot focus.
• The digital camera is capturing a video clip.
• The flash is charging, or the USB communication/ transfer is in progress.
The self-timer function is activated.
Self-timer LED Blinking red
• It is normal for the camera to become warm during operation, because the camera casing can conduct heat.
• The LCD display on this camera is manufactured with sophisticated technology, and more than 99.99% of the pixels on the LCD display meet standard specifications. Yet, it is possible that less than 0.01% of the pixels on the LCD display may have some light spots or show unusual colors. This is normal and does not indicate display malfunction, nor will this affect the pictures you take with the camera.
• The LCD monitor looks darker in strong sunlight or bright light. This is not a malfunction.
• To prevent your images from being blurred while pressing the shutter button, always hold the camera steady. This is especially important when you are shooting under low lighting conditions, under which your camera may reduce the shutter speed to ensure your images are properly exposed.
A
B
Preparing the camera for use
Use only the specified battery for the camera, and always turn off the camera before removing the battery.
To install the battery:
1. Open the battery cover (A).
2. Insert the battery in the correct direction by matching the + - label on the battery slot (B).
3. Push the battery all the way down.
4. Close the battery cover (D).
E1460_UM - EN.book Page 4 Thursday, September 23, 2010 6:43 PM
4 Preparing the camera for use
C To remove the battery:
1. Open the battery cover.
2. Pull the battery out (C).
3. Close the battery cover (D).
D
Charging the battery
The battery charge status affects the camera performance. To maximize the performance and the battery life, fully charge the battery using the camera and a wall outlet (or a computer), and then fully discharge it through normal use at least once.
To charge the battery via a wall outlet:
1. Turn off the camera.
2. Insert the battery into the camera.
3. Connect one end of the USB cable to the camera.
4. Connect the other end of the USB cable to the power adapter.
5. Plug in the power adapter to a wall outlet. The battery will start charging immediately.
To charge the battery via a computer:
1. Turn on the computer.
2. Turn off the camera.
3. Insert the battery into the camera.
4. Connect one end of the USB cable to the camera.
5. Connect the other end of the USB cable to your computer. The battery will start charging immediately.
You need to follow the instructions above to ensure successful charging.
E1460_UM - EN.book Page 5 Thursday, September 23, 2010 6:43 PM
Preparing the camera for use 5
• Turn off the camera before removing the battery.
• Please fully charge the Li-ion battery before using it for the first time.
• When the battery is being charged, the status LED indicator flashes in green. When the battery is fully charged, the status LED indicator is off.
• Use only the specified battery type. Using other types of battery may damage the camera and invalidate the warranty.
• Ensure that the Li-ion battery is inserted into the product with correct polarity. Incorrect polarity may damage the camera or cause fire.
• Download all pictures and remove the battery from the camera if you are going to store the camera for a long time.
• Damage caused by the use of an incorrect power adapter is not covered under the warranty.
• The battery may be warm after being charged or used. This is normal and not a malfunction.
• When using the camera in a cold environment, keep the camera and its battery warm by holding it inside your jacket or another warm protective environment.
Using multifunctional buttons
You can choose camera settings by pressing the 4-way control or the
1.
Left/Focus :
• Scrolls left in menus.
• Toggles between different focus modes.
2.
Up :
• Scrolls up in menus.
• Turns on/off Face Tracking. See "Face Tracking" on page
• Rotates an image. See "Rotating an image" on page 32
for details.
3.
Right/Flash :
• Scrolls right in menus.
• Selects a flash mode.
4.
Down :
• Scrolls down in menus.
5.
: Confirms a chosen setting.
button.
E1460_UM - EN.book Page 6 Thursday, September 23, 2010 6:43 PM
6 Preparing the camera for use
Using an SD card
The camera comes with internal memory for storing captured images, video clips, or audio files. You can also add an SD card to store more files.
To install an SD card:
1. Make sure the camera is turned off.
2. Open the memory card cover.
3. Insert an SD card in the correct direction.
4. Close the memory card cover.
To remove an SD card:
1. Make sure the camera is turned off.
2. Open the memory card cover.
3. Lightly press the edge of the memory card to eject.
4. Close the memory card cover.
Before initial use of an SD card, please format the card first by pressing
Manage Memory > > .
> >
E1460_UM - EN.book Page 7 Thursday, September 23, 2010 6:43 PM
Initial setting 7
Initial setting
You will be prompted to set up the language and the date and time when the camera is turned on for the first time.
Setting language
Selects the language version shown on the screen.
To select a language:
1. Press > initial setting is done.)
. (Step 1 is needed only after the
2. Press or to locate , SET
OK
MENU and then press or .
3. Press
4. Press
, , , or
to set the language.
to locate the language you want.
Setting date and time
When first time using the camera or the battery has been removed from the camera for a long time, you need to set the date and time. They are used to record when a file was captured.
To set date and time:
1. Press > initial setting is done.)
. (Step 1 is needed only after the
2. Press or to locate Date/Time , and then press or .
Polski
Română
3. Press or to select date and time and date format. Press move to another column as needed.
4. Press to set the date and time.
or to
E1460_UM - EN.book Page 8 Thursday, September 23, 2010 6:43 PM
8 Operating the camera
Operating the camera
The procedure below is a general guideline for basic operation. It is particularly useful if you are new to the camera.
1. Press the Power button to turn the power on.
2. Slide the mode switch to and press > , , , or to locate desired options (under two different tabs: make selections.
and ), and then press or to
Remember to follow the on-screen display or slide to for instructions (wherever available). Next, press corresponding buttons to access and set more options. At any time, you can cancel the current operation by pressing to return to your previous step.
3. Slide to to zoom-in or to zoom-out.
4. Press the shutter halfway to set automatic focus. Once the focus is set, the focus frame color will turn from white (unfocused) to green (focused). If the focus frame color is red and you press the shutter down, it might result in a blurred photo.
5. Press the shutter down fully to capture.
6. Release the shutter.
7. Slide the mode switch to and enter the Movie Record mode. Next, adjust the optical zoom as needed and press the shutter down to start video recording (press the shutter again to stop video recording).
8. Slide the mode switch to and view captured images or recorded videos. You can press , or to move to different images/videos, slide to press or out a captured image, or slide to to view 9 images on the screen.
to zoom-in/
• During zoom-in/out, there is a separator in the zoom bar between and best image quality, it is recommended to use optical zoom only by keeping the
. For magnification within and the separator.
• Flash is automatically turned off in the Movie Record mode.
• The Movie Record mode records both sound and video. The recording time is continuous, but recording will stop once the memory card space is full.
• In the Movie Record mode, sound is temporarily muted during zoom-in/out.
• At any time, you can press the Power button to turn off the camera.
• In Capture or Playback mode, press screen.
to decide what information to show on the
Digital Zoom
Optical Zoom
E1460_UM - EN.book Page 9 Thursday, September 23, 2010 6:43 PM
Capture mode
P
Capture mode 9
Item Description
6
7
4
5
1
2
3
Shooting mode
Flash mode
Focus mode
Drive mode
AEB
S.S.F.
Number of shots available
8
9
Image size
Image quality
10 Face Tracking
11 ISO
12 White Balance
13 AE metering
14 Exposure value (EV)
15 AF area
16 Histogram
17 Battery status
18 Camera shake warning
A
Page reference
--
--
--
--
E1460_UM - EN.book Page 10 Thursday, September 23, 2010 6:43 PM
10 Capture mode
• In the Capture mode, press to toggle among 5 display modes (standard, complete, none, rule of thirds, and Help Screen).
• Use the rule of thirds display mode to improve your composition by placing subjects on at least one of the intersections of these 4 imaginary lines.
• Help Screen diagram provides a quick overview to the major functions of camera buttons.
• While the shutter is pressed halfway, the shutter speed and the aperture are also shown on the screen (not available in the Movie Record mode).
• While the shutter is pressed down halfway, the AF area color changes to yellow-green, camera shake warning (appears only if the camera itself detects possible shaking), aperture, shutter speed and ISO setting are also shown on the screen.
More capture options in the Function menu
Press the Function button to access more capture options. Depending on your settings, the displayed option icons in the Function menu may vary.
Resolution
Image Quality
My Mode
(the 6 most recent record modes, in the order used)
Exposure Value
(EV)
White Balance
ISO
Metering
Effect
To use the Function menu:
1. Press to enter the Function menu and currently selected setting shows.
2. Press
3. Press
, to go to another option, or press
to confirm the setting.
or to select a setting.
E1460_UM - EN.book Page 11 Thursday, September 23, 2010 6:43 PM
Capture mode 11
Flash mode
The flash offers an additional light source (usually used in a low-light environment). You can capture an image using one of the following flash modes.
Icon Mode Description
Auto Flash
Auto Anti Red-eye
Force On
Slow Sync
Force Off
The flash fires automatically based on the photographic conditions.
Reduces the red-eye phenomenon when capturing natural-looking images of people and animals in low-light conditions. Be sure to ask the subject to look at the camera lens or get as close to the camera as possible.
The flash fires automatically based on the photographic conditions.
The flash always fires regardless of the surrounding lighting conditions. Select this mode when capturing images with high contrast (backlighting) and deep shadows.
Fires the flash immediately at the beginning of exposure with a longer shutter speed, so balanced ambient lighting of the foreground subject and background scene can be reached in a low-light environment.
The flash does not fire. Select this mode when flash photography is prohibited, or when the distance to the subject is beyond the effective range of the flash.
To select a flash mode:
1. Go to the Capture mode.
2. Keep pressing to toggle among different flash modes and select a desired option.
Face Tracking
Focuses on the position of faces (max. 10 faces) simultaneously. While using the Face
Tracking function, point the camera to where the people (your subjects) are located. Focus frames of Face Tracking will automatically detect faces (maximum 10) and show on the
LCD screen.
• Due to environmental factors such as lighting, the number of detected faces might be different from that of the actual faces.
• To achieve the best result, ask your subjects not to turn their faces partially away from the lens.
E1460_UM - EN.book Page 12 Thursday, September 23, 2010 6:43 PM
12 Capture mode
Focus mode
Icon Mode
Auto focus
Macro
Pan Focus
Infinity
Description
Adjusts focus automatically.
Used when capturing images at a close distance.
Used when you want to capture the subjects in a certain focus range.
Used when capturing images at long distance.
To select the focus mode:
1. Go to the Capture mode.
2. Keep pressing to toggle between Auto focus and focus modes.
Image size
Icon Description
14 megapixels (4320 x 3240)
Icon Description
3 megapixels (2048 x 1536)
3:2 (14 megapixels; 4320 x 2880)
8 megapixels (3264 x 2448)
5 megapixels (2592 x 1944) --
HD 16:9
(1920 x 1080 in full HD format)
VGA (640 x 480)
--
To select an image size:
1. Press .
2. Press or to select a setting.
Image quality
Icon Mode
Super Fine
Fine
Normal
Description
Best image quality with the lowest compression rate. File size is the largest.
Better image quality with medium compression rate. File size is medium.
Good image quality with the highest compression rate. File size is the smallest.
E1460_UM - EN.book Page 13 Thursday, September 23, 2010 6:43 PM
Capture mode 13
To select an image quality level:
1. Press Quality .
2. Press
3. Press
or to select a setting.
to confirm setting.
Setting EV
EV (Exposure Value) lightens or darkens the entire image. Adjust EV when the brightness between the subject and the background is not balanced, or when the subject occupies only a small part of the picture.
To select an EV:
2. Press or to select an EV from the EV bar. The preview result based on the currently selected EV is shown in the middle thumbnail.
3. Press to confirm setting.
Currently selected EV
Middle thumbnail
White Balance
Compensates for color temperatures in different lighting conditions, so white and other colors can display properly when you capture images.
Icon Mode Description
Auto Adjusts white balance automatically.
Daylight
Cloudy
Tungsten
Fluorescent H
Fluorescent L
Used in bright daylight conditions.
Used in twilight or shady conditions.
Used when subjects lit by tungsten (incandescent) lighting.
Adjusts for fluorescent lighting. Corrects the green hue of fluorescent lighting. Ideal for indoor photos under fluorescent lighting without a flash.
Manual Used when you want to manually adjust white balance in a particular lighting condition.
E1460_UM - EN.book Page 14 Thursday, September 23, 2010 6:43 PM
14 Capture mode
To select White Balance:
1. Press .
2. Press or to select a white balance option. The preview result based on the currently selected white balance is shown in the middle thumbnail. (When selecting the manual mode, you must first point the adjustment frame shown on the screen at a blank sheet of white paper or something similar, and press the Shutter for the camera to detect proper colors.)
3. Press to confirm setting.
ISO
ISO configures the camera’s sensitivity to light. The higher the ISO value, the brighter picture you can take in a low-light environment. Yet, you may see more noise in the picture as you increase the ISO value.
Icon Description
Automatically sets the ISO value.
Equivalent to color ISO 100/200 film. Used for outdoor photography in bright sunlight.
Equivalent to color ISO 400/800/1600/3200/6400 film. Used it in a low-light environment or where the flash light is not allowed.
• ISO 3200 for resolution of 3M or under only
• ISO 6400 for resolution of 3M or under only
To select an ISO value:
2. Press or to select an ISO Value.
3. Press to confirm setting.
AE metering
Icon Mode Description
Matrix Detects the exposure based on multiple points in the subject area.
Cent. Weight (Center Weight) Detects the exposure of the entire shooting screen, but gives more importance to the values near center.
Spot Detects the exposure based on the center spot in the subject area.
To select an AE metering option:
1. Press .
2. Press
3. Press
or to select an AE metering option.
to confirm setting.
E1460_UM - EN.book Page 15 Thursday, September 23, 2010 6:43 PM
Capture mode 15
Effect
Adds color filter effects to the image or video you want to capture.
Icon Mode Description
Normal No effects are added.
LOMO
Vivid
(For Movie Record only) Creates a lomo-like effect by adding over saturated colors, dark corners, and so on.
Adds an effect with very clear and bright color tones.
Sepia Adds an effect with dark reddish brown color tones, so the image or video looks as if it is old.
B/W (Black and White) Adds an effect with monochromatic color tones.
Vivid Red The image becomes reddish.
Vivid Green
Vivid Blue
The image becomes greenish.
The image becomes bluish.
Color Accent (Red) Highlights the subjects by keeping the red color domain of an image only while making other regions black and white.
Color Accent (Green) Highlights the subjects by keeping the green color domain of an image only while making other regions black and white.
Color Accent (Blue) Highlights the subjects by keeping the blue color domain of an image only while making other regions black and white.
Before After - when Color Accent (Red) is applied
E1460_UM - EN.book Page 16 Thursday, September 23, 2010 6:43 PM
16 Capture mode
After - when Color Accent (Green) is applied After - when Color Accent (Blue) is applied
To select an effect:
2. Press or to select an Effect option. The preview result based on the currently selected effect is shown in the middle thumbnail.
3. Press to confirm setting.
Shooting mode
Select one of the following shooting modes to fit your shooting condition.
Icon Mode Description
Auto Mode The camera automatically decide most settings, so you can capture images with ease.
Smart Scene Automatically selects a shooting mode based on the current shooting environment.
Program You can set the shooting parameters manually.
Aperture Priority You can choose an aperture value, while the shutter speed is automatically determined by the lighting condition of the subject.
E1460_UM - EN.book Page 17 Thursday, September 23, 2010 6:43 PM
Shutter Priority
Capture mode 17
You can choose a shutter speed, while the aperture value is automatically determined by the lighting condition of the subject.
Manual Lets you set both aperture and shutter speed manually.
Smile Catch Automatically takes a shot when a smile is detected.
Blink Detector Warns of eye blinks if detected & lets you decide whether to save the image file.
Portrait
Landscape
Sports
Backlight
Makes the subject (usually a person) stand out with smooth and natural-looking skin tones.
Captures a scene in the distance with the focus area set to infinity and a lower aperture value. The maximum depth of view can also be achieved.
Uses a high shutter speed to capture objects in motion.
Increases exposure (by turning on the flash) when light illuminates the subject from behind.
E1460_UM - EN.book Page 18 Thursday, September 23, 2010 6:43 PM
18 Capture mode
Night Scene Captures photos in a low-light environment, such as in the evening or at night.
Night Portrait
Self Portrait
Shoots night scenes and portraits clearly. Please keep the camera steady or use a tripod while using this mode.
Takes a self portrait with at least one face in a confined area.
Love Portrait Takes a self portrait with at least two faces in a confined area.
Pre-composition Captures the background first, so the helper can use it to take the final shot.
HDR Increases the dynamic range and enhances the details of dark areas.
LOMO
Fisheye
Creates a lomo-like effect by adding over saturated colors, dark corners, and so on.
Simulates a fisheye lens effect and creates a distorted hemisphere-like image.
E1460_UM - EN.book Page 19 Thursday, September 23, 2010 6:43 PM
Snow
Capture mode 19
Used under a very bright light environment such as snow scenes.
Fireworks
Building
Adds exposure time to shoot firework trails.
Please keep the camera steady or use a tripod while using this mode.
Enhances lines & contracts to highlight the sense of the three dimensions (3D) for a building.
Soft Flowing Water Uses a low shutter speed for motion blur. Please keep the camera steady or use a tripod while using this mode.
Web Auction Reduces the file size for faster internet upload.
Beauty Enhancer Enhances the tone of skin so that the facial skin appears smooth.
Food Captures food by enhancing color brightness and giving more vivid colors.
Candle Light Makes a picture look warm, and thus captures the mood under candle light source. Flash is always off.
E1460_UM - EN.book Page 20 Thursday, September 23, 2010 6:43 PM
20 Capture mode
Party Captures the party atmosphere usually under indoor light source.
Text
Child
Improves clarity & contrast when taking a close-up picture of documents.
Increases sensitivity and emphasizes children's skin tones.
Foliage
Sunset
Takes a clear and vivid picture of flowers or plant leaves by emphasizing their saturation and sharpness.
Captures the warmth and atmosphere
(represented by hue) of sunrise or sunset.
Voice Rec. (Voice
Record)
Captures background sound only (no images or videos). When listening to the captured audio file later, you can see a unique icon that appears on the screen and indicates that this is an audio file.
• ISO, Metering, and White Balance are not available in some shooting modes like Auto
Mode. You must select another mode like Manual to enable these options.
• When S.S.F. is turned on, adjusting ISO is unavailable no matter which shooting mode you select.
To select a shooting mode:
E1460_UM - EN.book Page 21 Thursday, September 23, 2010 6:43 PM
Capture mode 21
1. Press > ode > .
2. The currently selected shooting mode shows. Press desired option.
or to locate another
When you are selecting from different shooting modes, slide to for detailed explanation of each shooting mode. Slide to you are done.
3. Press to confirm setting.
to close the shooting mode description when
Aperture Priority
Aperture priority is often used when shooting static subjects or emphasizing the depth of field. In general, use a smaller aperture if a greater depth of field is needed.
To adjust aperture value:
1. Go to the Capture mode with Aperture Priority mode selected.
2. Press .
3. Press
4. Press
/ to adjust the aperture value.
to confirm setting.
Shutter Priority
Shutter priority is often used when shooting moving subjects. In general, use a shorter shutter speed to catch a fast-moving object.
To adjust shutter speed in Shutter Priority:
1. Go to the Capture mode with Shutter Priority mode selected.
2. Press .
3. Press
4. Press
/ to adjust the shutter speed.
to confirm setting.
Manual mode
You can choose the aperture value and shutter speed in Manual mode.
To adjust values in Manual mode:
1. Go to the Capture mode with Manual mode selected.
2. Press .
3. Press speed.
4. Press
/ to adjust the aperture value, or
to confirm setting.
/ to adjust the shutter
When toggling between Av/Tv, press the shutter halfway for exposure metering.
E1460_UM - EN.book Page 22 Thursday, September 23, 2010 6:43 PM
22 Capture mode
Drive mode
Icon Mode
Off (Single)
Description
Takes one picture at a time.
Self-timer
Double
Burst
Speedy Burst
Automatically takes a picture after 2 or 10 second delay.
This mode is useful when you want to be part of the picture.
Performs delay and capture twice:
1. Performs a 10-second delay, then captures the image.
2. Performs another 2-second delay then captures the image again.
Continuously takes pictures as long as you keep pressing the Shutter. The flash is always off in this mode.
Press and release the shutter. When the photo size you select is VGA, Speedy Burst will shoot continuously at the speed of 30 shots per second. This will stop after 1 second or when the memory card is full.
To select a drive mode:
1. Go to the Capture mode.
2. Press > .
3. Press or , and then select a desired option.
Auto Exposure Bracketing (AEB)
The AEB function automatically takes 3 pictures with slightly different settings in the shutter speed or the aperture value.
To turn on/off AEB:
1. Go to the Capture mode.
2. Press
3. Press or , and then select or .
AF area
Icon
Wide
Mode
Center
Description
Focuses on a wide range of multiple objects.
Focuses on the center area of the objects.
E1460_UM - EN.book Page 23 Thursday, September 23, 2010 6:43 PM
Capture mode 23
To select an automatic focus area:
1. Press > .
2. Press or , and then select a focusing area.
AF Assist Lamp
This function emits red light allowing the camera to focus easily when half pressed the
Shutter button.
To turn on/off AF Assist Lamp:
1. Go to the Capture mode.
2. Press > .
3. Press or , and then select or .
Setting sharpness, saturation and contrast
Adjusts how colors appear in the pictures by setting sharpness, saturation, and contrast.
To set sharpness, saturation, or contrast:
1. Press > , and then select Sharpness , Saturation or Contrast .
2. Press or , and then select High , Normal , or Low .
Digital Zoom
The digital zoom enlarges or shrinks the image using a software process.
Icon Mode Description
Wise Zoom Reduces the image size, and thus increases the effective zoom length without sacrificing image quality.
Digital Zoom Turns on the digital zoom feature.
OFF Turns off the digital zoom feature.
To select a digital zoom:
1. Press > .
2. Press or , and then select a digital zoom type or .
Date Stamp
Imprints the date when a picture was taken on the picture itself.
E1460_UM - EN.book Page 24 Thursday, September 23, 2010 6:43 PM
24 Capture mode
To set the date stamp:
1. Press > .
2. Press or , and then select Date , Date & Time , or .
Instant Review
This feature displays the still image that just recorded for 1 second.
To set the Instant Review:
1. Press > .
2. Press or , and then select or .
During instant review, half press the shutter to return to the capture mode.
Smart Scene
Automatically selects the best shooting mode from Portrait
, Backlight , Backlight Portrait , Night Portrait
, Landscape
, Night Scene
, Sunset
,
Snow , Text , Foliage , Macro environment and while the camera is held still).
, and Tripod (used in a low-light
1. Press > and select Smart Scene .
2. Press the shutter halfway to set automatic focus. The selected shooting mode is displayed in the top left corner of the screen.
3. Press the shutter to capture an image.
Blink Detector
Automatically detects blinking when you capture an image.
1. Press > and select Blink Detector .
2. Press the shutter to capture an image. If blinking is detected, a warning message appears on the screen.
3. Press / to save or discard the image, and then press to confirm.
Love Portrait
Takes a self portrait of at least two faces.
1. Press > and select Love Portrait .
2. Once faces are detected, the camera will automatically take a picture after a two-second countdown.
During the countdown, you can press the shutter to cancel the countdown. The camera will then start detecting faces again.
E1460_UM - EN.book Page 25 Thursday, September 23, 2010 6:43 PM
Capture mode 25
3. The camera continues to detect faces and take more pictures by repeating Step 2. This face tracking will automatically stop if no faces are detected.
Pre-composition
Captures the background first for positioning the final image. Ideal for asking others to take your photo.
1. Press > and select Pre-composition .
2. Press the shutter to capture the background. The bottom section of the screen displays the captured background image in a semi-transparent region.
3. Use the captured background image to frame the composition, and press the shutter to capture the final image.
Smile Catch
Captures an image when the subject smiles.
1. Press > and select Smile Catch .
2. The camera is tracking the face of your subject (a white frame shows).
3. Once a smile is detected, the camera instantly takes a picture.
4. The camera continues to detect smiles and takes more pictures (Step 3 is repeated).
Face tracking (one face only) is always on in the Smile Catch mode.
LOMO
Creates a lomo-like effect by adding over saturated colors, dark corners, and so on.
1. Press > and select LOMO .
2. Take a picture. (The LOMO effect will be applied to this picture immediately.)
When the LOMO effect is applied, color shift (changes in colors) might occur.
Before After
Fisheye
Simulates a fisheye lens effect and creates a distorted hemisphere-like image.
1. Press > and select Fisheye .
2. Take a picture. (The Fisheye effect will be applied to this picture immediately.)
E1460_UM - EN.book Page 26 Thursday, September 23, 2010 6:43 PM
26 Capture mode
Before After
Web Auction
Combines maximum 4 shots into one single image at the VGA (640 x 480) size, so it can be quickly used in situations such as Internet auctions.
1. Press > and select Web Auction .
2. Press or to move to the number of shots you want to take, and then press
Icon Mode Description
1 shot Takes one picture only.
.
2 shots Takes two pictures based on the numeric order shown below:
3 shots Takes three pictures based on the numeric order shown below:
4 shots Takes four pictures based on the numeric order shown below:
3. Press the shutter to take one picture.
4. If you are satisfied with the this picture, press to take the next one. (If you want to retake the previous picture, press and repeat Step 3.)
5. Once you have finished taking all pictures, the camera will automatically combine these images into one.
E1460_UM - EN.book Page 27 Thursday, September 23, 2010 6:43 PM
Capture mode 27
Movie Record mode settings
Icon Description
Video Format: HD 720p (16:9; 1280 x 720), VGA (640 x 480), QVGA
(320 x 240), or Web sharing (640 x 480).
• Video recording will automatically stop when the video file size reaches 4 GB.
• Video recording at HD 720p (16:9; 1280 x 720) will automatically stop when the video file size reaches 4 GB or the total recording time is near 29 minutes.
• Recording a video at HD 720p (16:9; 1280 x 720) requires a Class 6 or above SDHC card.
• Videos captured in Web sharing mode are stored under the
XXXUTUBE directory (XXX are numbers) with the file size limited to 1
GB or 10 minutes per video file (video recording will automatically stop).
White Balance: Auto, Daylight, Cloudy, Tungsten, Fluorescent H,
Fluorescent L, or Manual. See "White Balance" on page 13 for more
details.
AE metering: Matrix, Center, Spot. See "AE metering" on page 14 for
more details.
Effect: Normal, LOMO, Vivid, Sepia, B&W, Vivid Red, Vivid Green, Vivid
Blue, Color Accent (Red), Color Accent (Green), Color Accent (Blue).
See "Effect" on page 15 for more details.
Pre-record: On and Off
When Pre-record is on , the camera repeats recording a short video clip for a 3-second duration before you press the shutter. Once you press the shutter, the previous 3-second video clip will be combined into the current video you are shooting.
Only the latest 3-second video clip is stored temporarily on the memory.
To select a Movie Record option:
1. Slide the mode switch to
2. Press
and enter the
, and then select an option.
Movie Record mode.
3. Press
4. Press
or to select a setting.
to confirm setting.
E1460_UM - EN.book Page 28 Thursday, September 23, 2010 6:43 PM
28 Other settings
Battery status
Icon
Battery power is full.
Description
Battery power remains adequate.
Battery power is low.
Battery power is very low. You should replace the battery ASAP.
Other settings
Press > , and then select an option.
Option
Sounds
Power Saving
[Startup]
[Shutter]
[Operation]
[Volume]
[1 min.]
Description
Sets a type of the startup sound.
Sets the shutter sound on and off.
Sets the operation sound on and off.
Adjusts the volume of the shutter sound, startup sound, operation sound and playback sound.
For power conservation, the camera automatically enters the standby mode after it has been idle for a period of time. (Press any key to resume.)
[3 min.]
LCD Saving
Date/Time
[5 min.]
[Off]
The camera remains on when idle.
[On]
For power conservation, the LCD screen is automatically dimmed after the camera has been idle for 20 seconds. (Press any key to resume.)
[Off]
The LCD screen remains bright when the camera is idle.
Sets the date and time.
Select a language for display menus and other information.
E1460_UM - EN.book Page 29 Thursday, September 23, 2010 6:43 PM
File Numbering
TV Format
LCD Brightness
Manage Memory
Reset All
Other settings 29
[Series]
[Reset]
Stores the most recently used file number regardless of deleted files or a change of memory card. This is useful for avoiding the file name duplication when images are downloaded to a computer.
Resets file numbering each time the memory card is changed.
You can review images on a television with an AV cable.
[NTSC]
America, Japan, Taiwan and others
[PAL]
China, Europe, Oceania, and others
TV Format should be set to either NTSC or PAL depending on your region. For details about which system should be used, check with your local authorities.
[Auto]
[High]
The LCD brightness is automatically set based on the surrounding environment.
The LCD brightness is increased.
[Normal]
The LCD brightness remains at the default value.
[Format]
Formats the internal memory or the memory card.
Card]
[Copy to
Copies files from the internal memory to the memory card.
Resets the entire menu and button operation settings to initial default.
The following settings do not change after Reset All:
Date & Time setting
Language setting
TV Format setting
E1460_UM - EN.book Page 30 Thursday, September 23, 2010 6:43 PM
30 Other settings
Auto Rotation
[On]
[Off]
Automatically changes the image orientation (for viewing on the camera only; actual image content is not changed) as you change the camera holding position.
For example, if an image was taken when the camera was held horizontally, the image will still be displayed horizontally (its original orientation) during playback when the camera is held vertically.
E1460_UM - EN.book Page 31 Thursday, September 23, 2010 6:43 PM
Playback mode 31
Playback mode
Slide the mode switch to and enter the Playback mode.
IMG 0064.JPG
1.25MB
1/200 F2.8
12M
EV
2.0
While pausing video playback, you can press the shutter to capture the video frame as a still image in the VGA format.
Item
6
7
8
9
4
5
1
2
3
Description
Indicates that the camera is in the Playback mode.
Indicates that the file is protected and cannot be deleted.
Indicates this file has a voice memo or the file is an audio file.
Indicates the file is marked for printing.
Displays the shooting parameters when you took the picture or playback controls. Press between different displayed information.
to toggle
Date and time when the file was created.
File number
Histogram
File name, file size, shutter speed, and aperture value
Page reference
--
--
--
--
--
--
--
E1460_UM - EN.book Page 32 Thursday, September 23, 2010 6:43 PM
32 Playback mode
Options for playback and editing
When the camera is in the Playback mode, press , or to move to different files. You can also select any of the following options.
Enlarging an image
Magnifies an image, so more details can be seen.
To enlarge an image:
1. Slide the mode switch to .
2. Press or to move to the image you want to enlarge.
3. Press to zoom-in or to zoom-out.
4. Press
5. Press
, , , or to move to the area you want to see.
to return to the normal viewing size.
Rotating an image
You can press time.
to change the orientation of an image at 90 degrees clockwise at a
For each rotation, the image file in the new orientation is automatically saved.
Viewing multiple files at a time
Shows up to 9 files at a time on the screen.
To view multiple files:
1. Slide the mode switch to
2. Slide to
.
. In this mode, maximum 9 files (shown in thumbnails) are displayed on the
or screen. Press , , , or to select a file, and then press
to view it in its normal viewing size.
3. Slide to . In this mode, all files are arranged by dates. Press , , , or
to select a file, and then press or to view it in its normal viewing size.
If there are more than 9 thumbnails, you can press repeatedly until the scroll bar is highlighted. Then you can press to move to the previous 9 thumbnails or to move to the next 9 thumbnails. To cancel highlighting the scroll bar, just press .
E1460_UM - EN.book Page 33 Thursday, September 23, 2010 6:43 PM
Playback mode 33
Playing back video clips
View recorded video clips in the playback mode.
To view a video clip:
1. Slide the mode switch to .
2. Press or to move to the video clip you want to view.
3. Start playing back.
• Press to start playing the video clip.
• Press to resume.
to stop the video clip, or press to pause it. Press again
• During video playback, press to fast forward or press to rewind.
• While pausing video playback, you can press the shutter to capture the video frame as a still image in the VGA format.
• While pausing video playback, you can view the video frame by frame. Press to fast forward one frame, or press to rewind one frame. Press and hold to fast forward frame by frame continuously, or press and hold to rewind frame by frame continuously.
Adjusting the playback volume
Increase or decrease the volume of video clips, audio clips, or voice memos.
To adjust the playback volume:
1. Turn the power on, and set the camera to the playback mode.
2. Press or to select a video clip, audio clip, or voice memo that you want to playback.
3. Adjust the volume.
• Slide to to increase the volume.
• Slide to to decrease the volume.
The volume can be set during playback, but not during rewind, fast forward, or pause.
Slideshow
Sets the time interval for presenting a series of captured image and video files (first frame only).
To play a slideshow:
1. Slide the mode switch to .
2. Press > > or .
3. Change the slideshow settings.
• Use the four-way control to set one of the following slideshow effects:
• Applies a transition effect from left to right.
• Applies a transition effect from upper-left side to lower-right side.
E1460_UM - EN.book Page 34 Thursday, September 23, 2010 6:43 PM
34 Playback mode
•
•
Applies a horizontal transition effect.
Applies a vertical transition effect.
• Applies a horizontal transition effect by intersecting an image.
• You can set the interval between 1/3/5/10 seconds.
4. Select whether you want to repeat the slideshow.
5. Select Start and press to play the slideshow.
If you want to pause it at any time, press stop the slideshow, press .
. Press again to resume playback. To
Deleting files
Removes selected or all files.
To delete files:
1. Slide the mode switch to .
2. Press or .
3. Select whether to delete this selected file, other selected, all files, or voice memo only, and then press .
Protecting files
Prevents selected files from accidental removal.
To protect files:
1. Slide the mode switch to .
2. Press > > or .
3. Select whether to protect this selected file, other selected, or all files, and then press
You will then see the icon indicating the file is protected.
.
You can remove the protection anytime by following the same procedure as shown above.
Note that in Step 2 the on-screen instruction will ask you how you want to remove the protection.
Red-eye Removal
The Red Eye Correction function is used to reduce red eye in captured images. This function is only available for still images. Red eye correction can be applied to an image several times, but the quality may gradually deteriorate.
1. Slide the mode switch to .
2. Press or to move to the image you want to apply Red-eye Removal.
3. Press
4. Press
> > or .
to confirm the change and save the image file.
Voice memo
Inserts a voice annotation to an image file.
E1460_UM - EN.book Page 35 Thursday, September 23, 2010 6:43 PM
To record a voice memo:
1. Slide the mode switch to .
2. Press or to move to the image you want to add a voice memo.
3. Press > >
4. Select Start >
5. Select Stop > to stop recording.
or
to start recording your voice.
.
To play back a voice memo:
1. Press to play the voice memo.
2. Press to pause the playback.
3. Press
4. Press
to resume the playback.
to exit playback.
Photo Effect
You can add special effects to your images.
Icon Option
Normal
Description
No effect is added to the image.
Playback mode 35
Sepia
B / W
Recorded image will be stored in a sepia tone.
Convert image to black & white.
Negative
Mosaic
Colors become the opposite of what they were in the original image.
Applies a mosaic tile effect to the image.
Vivid Red The image becomes reddish.
Vivid Green The image becomes greenish.
Vivid Blue The image becomes bluish.
To add a special effect to an image:
1. Slide the mode switch to .
2. Press or to move to the image you want to add an effect to.
3. Press > > or .
4. Press , or to select the effect. The preview result based on the currently selected effect is shown in the middle thumbnail.
E1460_UM - EN.book Page 36 Thursday, September 23, 2010 6:43 PM
36 Playback mode
5. Press to confirm the change and save the image file.
Trimming
Crops part of an image file, reduces the image size, and overwrites the image file or saves it as another new file.
To trim an image:
1. Slide the mode switch to .
2. Press or to move to the image you want to trim.
3. Press
4. Slide to reduce.
or
or .
to select the target image size (8M, 5M, 3M, VGA) to which you want to
5. Press
6. Press
, , , or to locate the area to trim.
to confirm the change and save the image file.
You cannot trim images in the size of 3:2, 16:9, or VGA.
Resizing
Changes an image file to a smaller size, and overwrites the image file or saves it as another new file.
To resize an image:
1. Slide the mode switch to .
2. Press or to move to the image you want to resize.
3. Press > > or .
4. Press
5. Press
or to select the target image size to which you want to reduce.
to confirm the change and save the image file.
E1460_UM - EN.book Page 37 Thursday, September 23, 2010 6:43 PM
Playback mode 37
Startup image
Sets the welcome screen when the camera is powering on.
To select a startup image:
1. Press > > or .
• To use the default startup image, select Default .
• To use a custom image, select My Photos and press
• To disable the startup image, select Off .
2. Press .
or to select an image.
DPOF
The Digital Print Order Format (DPOF) setting allows you to select images on the memory card for printing and specify the number of print copies in advance using the camera. This is extremely convenient for sending the images to a photo developing service or for printing on a direct print function compatible printer.
To set up DPOF:
1. Press
2. Press or and select one of the following options.
• To set the DPOF setting for one image in a time, select One . and press select an image.
• To set the DPOF setting for all images in a time, select All .
• To clear all DPOF settings to initial default, select Reset .
3. Press
4. Press
5. Press .
or to specify the number of copies.
to decide whether you want to turn the date stamp on.
Radial Blur
Applies a rotating motion effect to give a feel of speed.
To apply a Radial Blur effect:
1. Slide the mode switch to .
or to
2. Press > >
3. Press
4. Press
or
or .
and select a degree of Radial Blur.
to confirm the change and save the image file.
E1460_UM - EN.book Page 38 Thursday, September 23, 2010 6:43 PM
38 Playback mode
Active Display
When Active Display is on and the camera is in the playback mode, you can shake the camera clockwise (when the camera is held horizontally) to move to the previous file. To move to the next file, just shake the camera counterclockwise (when the camera is held horizontally).
To enable/disable Active Display:
1. Slide the mode switch to .
2. Press > > or .
3. Select On to enable Active Display or Off to disable Active Display.
4. Press .
Clockwise: move from the current file (No. 3) to the previous file (No. 2).
Counterclockwise: move from the current file
(No. 3) to the next file (No. 4).
E1460_UM - EN.book Page 39 Thursday, September 23, 2010 6:43 PM
Working with computer and AV system 39
Working with computer and AV system
Bundled software
The camera offers the following programs on a CD.
ArcSoft
PhotoImpression 5
ArcSoft
VideoImpression 2
Combines photo editing with creative enhancement and sharing tools that maximize your digital media experience.
Creates multimedia presentations by combining photos and video clips with audio, text and scene transitions.
To install these programs, see the information supplied with the CD.
Connecting the camera to a computer
You can connect the camera to a PC or notebook to transfer, view, print, or edit files as well as charge the camera.
To connect the camera to a computer:
1. Connect the end of the smaller plug of the USB cable to the camera.
2. Turn on the camera.
3. Connect the other end of the USB cable to an available USB port on your computer.
4. Select Computer and wait for the connection.
5. A Removable Disk icon appears in My Computer . Click this icon to access the files in your camera.
• When connecting the camera to a computer, it is necessary to install a battery into the camera.
• When connecting the camera to a computer, please use the original accessory of the
USB cable to avoid possible system conflicts and damage to the camera.
Connecting the camera to an AV system
You can play files in your camera from an AV system such as TV or projector.
To connect the camera to an AV system:
1. Connect the end of the smaller plug of an AV cable to the camera.
2. Connect the yellow video plug and the white audio plug of the AV cable to a video-input jack and an audio-input jack (left channel) on your AV system.
3. Turn on the AV system, and then switch to the AV source connecting to the camera.
4. Turn on the camera.
5. Follow the on-screen instructions to operate the camera via the TV or projector screen.
Printing images
In addition to printing images by connecting the camera to a printer via a computer or bringing the memory card (if available) to a photo-processing center, you can choose to print using PictBridge.
Printing with PictBridge
You can directly print images by connecting your camera to a PictBridge-compatible printer without using a computer.
E1460_UM - EN.book Page 40 Thursday, September 23, 2010 6:43 PM
40 Working with computer and AV system
To print images from a PictBridge-compatible printer:
1. Connect the end of the smaller plug of the USB cable to the camera.
2. Connect the other end of the USB cable to an available USB port on your printer.
3. Turn on the printer. Wait for a while until it finishes starting up and is ready to print.
4. Turn on the camera.
5. Select Printer and wait for the connection.
6. Select one of the following options:
• To print one image in a time, select Print One , and press or to select an image.
• To print all images in a time, select All .
• To print all images (shown by thumbnails) in a time, select Index .
7. Press .
• The above procedure may vary depending on the printer type you are using.
• If you connect the camera to your printer while the printer is still starting up, the camera will be automatically turned off.
• Failure to follow the above procedure will make the camera show an error message.
Please disconnect the camera and the camera will be automatically turned off.
E1460_UM - EN.book Page 41 Thursday, September 23, 2010 6:43 PM
Troubleshooting and service information 41
Troubleshooting and service information
If your camera cannot operate normally, see the frequently encountered problems and solutions listed below. If the problem persists, contact your nearest service center or technical support.
Problem Cause Solution
The camera cannot power up.
The battery power is draining quickly.
There is no battery or the battery is not inserted correctly.
Insert the battery correctly.
The battery has no power.
Replace the battery.
The external temperature is extremely low.
Many shots are being captured in dark places, requiring a flash.
--
--
The battery or camera is warm.
The camera or flash was used continuously over a long period of time.
The flash does not fire or recharge.
The camera flash is turned off.
The light source is sufficient.
Even though the flash fired, the image is dark.
The distance to the subject is greater than the flash's effective range.
The image is too bright or too dark.
I cannot format a memory card.
I cannot download images from the camera to my computer.
The exposure is excessive or inadequate.
The memory card is writeprotected.
End of the memory card life.
The free space on the hard disk of your computer is insufficient.
There is no power being supplied to the camera.
--
Set the flash to Auto Flash.
--
Get closer to the subject and shoot.
Reset exposure compensation.
Remove the write protection.
Insert a new memory card.
Ensure that the hard disk has enough space for running Windows and that the drive for loading image files has free space equal to or greater than the memory card in the camera.
Replace the battery.
E1460_UM - EN.book Page 42 Thursday, September 23, 2010 6:43 PM
42 Troubleshooting and service information
The camera does not shoot even when pressing the shutter button.
The battery is running low.
The camera is not in the Capture mode.
Replace the battery.
Switch to the Capture mode.
The shutter button was not pressed all the way down.
Press the shutter button all the way down.
The internal memory or memory card does not have any free space.
Load a new card or delete unwanted files.
I cannot print images with
PictBridgecompliant printers.
The flash is recharging.
Wait until the flash mode icon, indicated on the screen, stops flashing.
The camera does not recognize the memory card.
Format the memory card before the initial use or before using with another camera.
The camera is connected to the printer when the camera is powered off.
Connect the camera to the printer, turn on the camera, and then select
Printer .
Technical support
For technical assistance, free driver updates, product information, and news releases, visit the following web site:
http://www.BenQ.com
E1460_UM - EN.book Page 43 Thursday, September 23, 2010 6:43 PM
Specifications 43
Specifications
Sensor
Zoom
Lens
Focus Range
LCD
Image Resolution
Movie Mode
Shutter Speed
White Balance
Sony 14 Mega Pixels, 1/2.3 inch CCD
Optical: 4X
Digital: Up to 5X (Preview) / Up to 12X (Playback) f = 5.05 (W) ~ 20.2 (T) mm
F: 2.8 (W) ~ 6.3 (T) f = 28 mm ~ 112 mm, 35 mm equivalent
Normal: W= 12 cm ~ Infinity
Macro: W= 12 cm ~ 100 cm
2.7” LCD 230k pixels
• 14M (4320 x 3240)
• 3:2 (4320 x 2880)
• 8M (3264 x 2448) / 5M (2592 x 1944) / 3M (2048 x 1536) /
HD 16:9 (1920 x 1080 in full HD format) / VGA (640 x 480)
HD 720p (16:9; 1280 x 720), VGA (640 x 480), QVGA (320 x 240), or
Web sharing (640 x 480)
30 fps
Continuous recording with sound
1/2000 ~ 1 sec (Fireworks 2 sec.; Manual, Night Scene 15 sec.)
Auto, Daylight, Cloudy, Tungsten, Fluorescent H, Fluorescent L,
Manual
-2 ~ +2 EV (0.3EV / step) Exposure
ISO
Flash
Drive mode
Power Source
• Auto / 100 / 200 / 400 / 800 / 1600
• ISO 3200 for resolution of 3M or under only
• ISO 6400 for resolution of 3M or under only
Auto Flash / Auto Anti Red-eye / Force On / Slow Sync / Force Off
Off (Single) / 10 sec. (Self-timer) / 2 sec. (Self-timer) / Double / Burst /
Speedy Burst
700mAh rechargeable Li-ion battery
CIPA approximately 160 based on bundled Li-ion battery
Storage Type
File Format
Built-in approx. 11.5 MB
4GB SD / 32GB SDHC card compatible
Still Image: JPEG (EXIF 2.2 compatible); DCF compatible
Supported file formats:
• Video: MJPEG
• Audio: WAV
Dimensions / Weight 91.6 x 57.8 x 16.6 mm
100 g (w/o battery & SD card)
Interface Digital output: USB 2.0 compatible
Audio / Video output (NTSC/PAL)
PictBridge compatible
E1460_UM - EN.book Page 44 Thursday, September 23, 2010 6:43 PM
44 Specifications
Accessories USB Cable / Software & User Manual CD / User Manual or Quick
Guide / Hand Strap / Leather case / Li-ion battery / AC power adapter
Available accessories depend on the actual items shipped and may vary from the list above.
All information, designs, and specifications are subject to change without prior notice.
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce
Nøglefunktioner
Compact camera 14 MP CCD Silver
Image sensor size: 1/2.3"
Optical zoom: 4x Digital zoom: 5x
Video recording 1280 x 720 pixels HD
Built-in microphone PictBridge
Lithium-Ion (Li-Ion)